PSI Laser Printer Programming Guide

Programming Guide

for PSi Laser Printers

PP 3034 and PP 4050/60

2

Preface

The printer supports the PJL Printer Job Language and PCL5 Printer Language.

All the printes unique feature and funcons can be controlled by the applicaon soware via PJL or PCL5

commands.

The features described below refer to the Firmware Revision V2.xx of the printer.

Note: For more informaon regarding PJL and PCL5 programming please refer to the

• PJL Printer Job Language (5961-0704)

• PCL5 Printer Language Technical Reference Manual (5961-0509)

published by Hewle-Packard ® Company.

3

Content

Preface ....................................................................................................................................... 2

1 Support of Printer Specic Features and Funcons ............................................................... 4

2 List of Supported PJL Control Funcons ................................................................................. 7

3 List of Supported PCL5 Control Funcons ............................................................................ 13

3.1 Job Control Commands ................................................................................................. 13

3.2 Page Control Commands ............................................................................................... 14

3.3 Cursor Posioning Commands ...................................................................................... 15

3.4 Font Selecon Commands ............................................................................................ 16

3.5 Font Management Commands .............................................................................. ........ 17

3.6 Macro control Commands ............................................................................................. 18

3.7 Graphic Commands ....................................................................................................... 18

3.8 Status Readback Commands ......................................................................................... 19

4 Support of Semigraphics for SAP/R3 .................................................................................... 20

5 Barcode Programming .......................................................................................................... 21

5.1 Resident Barcode Font Code 39 HP Compable ........................................................... 21

5.2 Resident Barcodes Controlled by Private Command Sequences ................................... 22

5.3 Barcode Progamming Examples .................................................................................... 30

6 Symbol Sets .......................................................................................................................... 37

6.1 Roman-8 ....................................................................................................................... 37

6.2 ISO 8859/1 Lan 1 ......................................................................................................... 38

6.3 ISO 8859/2 Lan 2 ......................................................................................................... 39

6.4 ISO 8859/9 Lan 5 ......................................................................................................... 40

6.5 ISO 8859/15 Lan 9 ....................................................................................................... 41

6.6 PC-8 Code Page 437 ...................................................................................................... 42

6.7 PC-8 Danish/Norwegian ................................................................................................ 43

6.8 PC-850 Mullingual ...................................................................................................... 44

6.9 PC-852 Lan 2 ............................................................................................................... 45

6.10 PC-858 Mullingual ..................................................................................................... 46

6.11 PC-Turkish ................................................................................................................... 47

6.12 Windows 3.1 Lan 1 .............................................................................. ...................... 48

6.13 Windows 3.1 Lan 2 .............................................................................. ...................... 49

6.14 Windows 3.1 Lan 5 .............................................................................. ...................... 50

6.15 Desktop ....................................................................................................................... 51

6.16 PS text ......................................................................................................................... 52

6.17 Ventura Internaonal .................................................................................................. 53

6.18 Ventura US .................................................................................................................. 54

6.19 Microso Publishing ................................................................................................... 55

6.20 Math-8 ........................................................................................................................ 56

6.21 PSMath ........................................................................................................................ 57

6.22 PS MAth ....................................................................................................................... 58

6.22 PI FONT ....................................................................................................................... 59

6.23 LEGAL .......................................................................................................................... 60

6.24 ISO UNITED KINGDOM ................................................................................................ 61

6.25 ISO US ASCII ................................................................................................................ 62

6.26 ISO SWEDISH ............................................................................................................... 63

6.27 ISO ITALIAN .................................................................................................................. 64

6.28 ISO SPANISH ................................................................................................................ 65

4

Content

6.29 ISO GERMAN ............................................................................................................... 66

6.30 ISO NORWIAN ............................................................................................................. 67

6.31 ISO FRENCH ................................................................................................................. 68

6.32 Windows 3.0 Lan 1 .............................................................................. ...................... 69

6.33 Windows 3.0 BALTIC .............................................................................. ...................... 70

6.34 SYMBOL ....................................................................................................................... 71

6.35 WINDINGS ................................................................................................................... 72

6.36 MICR CMC7 ................................................................................................................. 73

6.36 MICR E13B .............................................................................. ..................................... 74

5

1 Support of Printer Specic Features and Funcons

The Fanfold Laser Printer provides programming support of Printer Specic Features and Funcons. The-

se Funcons are implemented with special Printer Job Language commands. The following hints show in

combinaon with applicaon examples how to use and program these funcons:

1.1 Proles

The printer can store up to 10 separate printer conguraon sengs called Proles. One prole

should be used for one specic applicaon. This applicaon may require a special seng for the

paper format, the paper path, fuser temperature, etc.

In an system environment where the applicaon can not use a driver to select the applicaon speci-

c parameters a prole can be selected by means of a specic PJL command which has to be sent to

the printer before sending the print data.

Example:

ESC%-12345X@PJL DEFAULT PROFILE = 5

ESC%-12345X

1.2 Paper Size Select

The printer supports paper format A4, Leer and CUSTOM. With paper format CUSTOM the page size

can be set by PJL commands. These PJL commands have to be sent to the printer before sending the

print data. In the following example (with PJL SET) the paper format selecon is only valid for one PCL

applicaon le. Aer a power o or PJL reset the USER DEFAULT environment variables are valid:

Example:

ESC%-12345X@PJL SET PAPER = CUSTOM

@PJL SET PAGELENGTH = 11 1/3

@PJL SET IMAGEWIDTH = 7.15

@PJL ENTER LANGUAGE = PCL

ESCE......PCL applicaon le.....ESCE

1.3 Paper Path Control

The paper path for the printer can be controlled by soware. This can be done either by PJL or by PCL

commands which have to be sent at the beginning of an applicaon le.

Note: The acceptance of PJL or PCL commands to select the paper format and paper path depends on

the conguraon of PAPER SELECTION and PAPER PATH SELECT.

1.4 Semigraphics Support under SAP R/3

To increase the printer performance when the printer is running under SAP R/3 PSi provides a printer

specic SAP R/3 device type. These device type makes use of the special semigraphic line draw ele-

ments. (see chapter A-4 Support of Semigraphics for SAP/R3)

The SAP R/3 device type ZPSI4050.PRI including installaon descripon can be downloaded from the

PSi Laser homepage:hps://www.psi-laserdrucker.de

6

6 Symbol Sets 37

1.5 EURO Symbol Support

The printer supports prinng of the EURO symbol as printer resident character within the following

code tables (see also Appendix B):

• ISO 8859 / 15 LATIN 9

• PC - 858 Mullingual

• SYMBOL

• WINDINGS

Note: The EURO symbol is supported in combinaon with a restricted number of printer typefaces

1.6 Support of Logical Pages and Physical Pages

One Physical Page can be spit up into a number of Logical Pages by the parameter LENGTHFACTOR.

The page length must be congured or programmed according to the physical length of one page to

ensure proper funcon of the aached stacker. Up to 20 logical pages can be placed on one physical

page. The length limit for an aached stacker (minimum page length is 8 inch) is only valid for the

physical page length. Two Logical Pages of 6 inch can be printed on physical paper with 12 inch length

by seng LENGTHFACTOR = 2.

The following example shows the PJL commands for an applicaon with image width = 8.5 inch and a

logical page length of 3 inch to be printed on a physical page length of 12 inch:

Example:

ESC%-12345X@PJL SET PAPER = CUSTOM

@PJL SET IMAGEWIDTH = 8.5

@PJL SET PAGELENGTH = 12

@PJL SET LENGTHFACTOR = 4

@PJL ENTER LANGUAGE = PCL

ESC E....PCL le page 1....FF....page 2....FF

....page3....FF ESC E....

Note: PJL or PCL commands which are related to the physical page like paper source, number of co-

pies, and cut force a feeding of the paper to the top of the next physical page.

These sengs are valid unl a PJL RESET condion. ( PJL SET command)

7

6 Symbol Sets 37

1.7 Support of Job Separaon

Every print job can be separated by a cut operaon at the end of the print job. If the parameter JOB-

SEPARATION = ON is set either by conguraon or by PJL command every PJL EOJ command triggers

a cut operaon. The following example shows how to program the automac separaon of two PCL

jobs by seng the parameter JOBSEPARATION to ON and using the PJL JOB and PJL EOJ commands at

the beginning and end of every PCL job:

ESC%-12345X@PJL DEFAULT JOBSEPARATION = ON

ESC%-12345X@PJL JOB

@PJL ENTER LANGUAGE = PCL

ESC E......PCL job 1.....ESC E

ESC%-12345X@PJL EOJ

ESC%-12345X@PJL JOB

@PJL ENTER LANGUAGE = PCL

ESC E......PCL job 2.....ESC E

ESC%-12345X@PJL EOJ

1.8 Convenons

The following convenons are used in the command lisngs:

Code Descripon

ESC • Escape (1/B), introduces an escape sequence

@• Introduce a PJL command

P1 (Pn)

• Numeric parameter, or number of units that specify a dis-

tance or quanty pertaining to the escape sequence, cont-

rol funcon or control string. Accepted values are 0...9999.

If the parameter is in normal notaon like „200“ the pro-

gramming in hex-code is according to a ASCII table. („200“ =

32,30,30 in hex).

<SP> • Spaces may appear between characters in sequence for cla-

rity; they are not part of the format. A Space character (hex

20) is indicated by <SP>.

<CR> • Carriage Return (hex 0D)

<LF> • Line Feed (hex 0A)

8

2 List of Supported PJL Control Funcons

The Fanfold Laser Printer provides limited support of Printer Job Language (PJL). PJL topics which are de-

scribed in this chapter are:

Basic Rules for PJL Programming

• PJL Environments

• List of supported PJL Commands

• List of supported PJL Variables and Values

• List of supported PJL Variables and Values for PCL Personality

For more informaon on topics covered in this secon, please refer to the

Printer Job Language Technical Reference Manual from Hewle-Packard, Inc.

2.1 Basic Rules for PJL Programming

Printer Job Language (PJL) command sequences are used to dene all specic parameters for one

print job. PJL commands provide the following major funcons:

• Printer language switching between jobs

• Job separaon

• Printer conguraon

• Status readback from the printer to the host

At the beginning of every print job the UEL command ( ESC % - 1 2 3 4 5 X ) is used to switch from the

print emulaon (PCL, Postscript, HEXDUMP...) to the PJL command level.

2.1.1 PJL Syntax Rules

• Use only uppercase characters

• All parts of a PJL command line must be separarted by a <SP> (Space)

• Every PJL command line must start with the prex @PJL.

• Every PJL command line must end with <LF> (Line Feed)

Exsample of typical PJL command line:

@PJL <SP>DEFAULT<SP> LPARM : PCL <SP> PTSIZE = 12<LF>

PREFIX <SP> COMMAND <SP> Com. Modier : Value <SP> Variable = Value<LF>

Note: The st PJL command aer the UEL must start with @PJL....! (no <SP>)

9

2 List of Supported PJL Control Funcons

2.1.2 PJL Environments

The factory default is stored in the

ash memory of the printer and can

not be changed by the user

Aer ....

• Power on

• RECALL FACTORY

• @PJL INITIALIZE

the printer default sengs are copied

from the Factory Defaults Environ-

ment into the User Default Environ-

ment

The User Default Environment set-

ngs are modied using the operator

panel keys and/or the @PJL DEFAULT

command

When a PJL reset occurs, the User De-

fault Environment sengs are loaded

into the PCL Current Environment

The PCL commands as part of the ap-

plicaon data streams changes the PJL

Current Environment sengs using

the @PJL SET command sengs

A language reset (ESC E or @PJL EN-

TER LANGUAGE) loads the PJL Current

Environment sengs into the Modi-

ed Print Environment

10

2 List of Supported PJL Control Funcons

2-1-3 List of Supported PJL Commands

PJL COMMAND DESCRIPTION

@PJL COMMENT [”text”] • The COMMENT command is used for adding a line of infor-

maon or a comment within a set of PJL commands.

@PJL JOB [NAME= ”text”]

[START= #] [END = #]

• Denes the name and pages of a PCL print job.

• NAME = le name (ASCII text)

• START = rst page, range 1 to 214783647

• END = last page, range 1 to 214783647

@PJL EOJ [NAME=”job name”]

• The EOJ command marks the end of the job which was star-

ted with the previous JOB command. It resets the PJL Cur-

rent Environment to the User Default Environment. The JOB

and EOJ commands should always be used in pairs. Do not

use one without the other.

@PJL ENTER LANGUAGE = personality • Supported personality opons are PCL , HEXDUMP

@PJL RESET

• The RESET command resets the PJL Current Environment va-

riables to their User Default Environment values (see Figure

on page before for a descripon of PJL Environments).

@PJL INITIALIZE

• The INITIALIZE command resets the PJL Current Environment

and the User Default Environment variables to their Factory

Default Environment values.

@PJL DEFAULT [LPARM : personality]

Variable = value

• The DEFAULT command sets the User Default Environment

value for a specied variable.

• Personality : PCL, HEXDUMP

• For supported variables and values see table: A-2.1.4 PJL

Variables and Values

@PJL SET [LPARM : personality]

Variable = value

• The SET command allows the user to change the value of

PJL Current variables for the length of a PJL job, or unl a PJL

reset condion returns the value to is default.

• Personality : PCL, HEXDUMP

• For supported variables and values see table: A-2.1.4 PJL

Variables and Values

@PJL RDYMSG [„text of message”]

• Display a message in the 1st line of the printes operator pa-

nel

• The message length is at max. 16 characters

• The printer remains online

@PJL RDYMSG [„”] • Clear the message on the printes operator panel

@PJL OPMSG [„text of message”]

• Display the message in the 1st line of the printes operator

panel

• The message length is at max. 16 characters

• The printer gets o line

• Aer prompng of this status by pushing the oine/on-

line buon, the printer goes ONLINE again

11

2 List of Supported PJL Control Funcons

PJL COMMAND DESCRIPTION

@PJL INQUIRE [ LPARM : personality ]

Variable

• Requests the default value for an environment variable.

• personality = PCL, HEXDUMP

• port =

• For supported variables and values see table: A-2.1.4 PJL

Variables and Values

@PJL DINQUIRE [ LPARM : personality ]

Variable

• Requests the default value for an environment variable.

• personality = PCL, HEXDUMP

• port =

• For supported variables and values see table: A-2.1.4 PJL

Variables and Values

@PJL INFO category

• Requests specied category of printer informaon.

Supported categories are:

• ID : Printer ID is PP 4050

• CONFIG : Printer conguraon

• MEMORY : Printer memory

• STATUS : Printer status

• VARIABLES : List of Environment variables

• USTATUS : List of USTATUS variables

• PROFILES : List of PROFILES

@PJL ECHO [ words ] • Returns the ”words” to the host computer.

@PJL USTATUS

variable = value

• Allows the printer to send unsolicited status messages. Sup-

ported variables and values are:

• DEVICE = ON : send aer status change

• DEVICE = VERBOSE : same as ON + PJL errors

• DEVICE = OFF : no status change messages

• JOB = ON : send at job start / end

• JOB = OFF : no job start/end message

• PAGE = ON : send at page end

• PAGE = OFF : no page end message

• TIMED = 5...300, 0 : send status aer me

@PJL USTATUSOFF • Turns o all unsolicited status messages

2.1.4 List of Supported PJL Variables and Values

The following variables can be programmed by the PJL commands:

• @PJL SET ”variable” = ”value”

• @PJL DEFAULT ”variable” = ”value”

PJL SET VARIABLE VALUES

PROFILE • 1, 2, 3, ....., 10

PAPER • A4, LETTER, CUSTOM

PAGELENGTH • 3, 3 1/6, ....., 20 in steps of 1 / 6 or 1 / 4 inch

Note: value 3 1/6 programming is 3<SP>1/6

12

2 List of Supported PJL Control Funcons

PJL SET VARIABLE VALUES

LENGTHFACTOR • 1, 2, 3, ...., 20

IMAGEWIDTH • 0.5, 0.55, ....., 16 in steps of 0.05 inch

PAPERSOURCE • LOWER,

• UPPER

PAPERDESTINATION

• BOTTOM

• TOP (PP 4050XP only)

• BOTTOMCUT

LENGTHFACTOR • 1, 2, 3, ...., 20

ORIENTATION • PORTRAIT

• LANDSCAPE

LANDSCAPEMODE • REVERSE

• PCLCOMPATIBLE

ORIENTATIONMODE • FIXED

• AUTOMATIC

PAPEREXTENDED • NO

• YES

PAPERSELECT

• RECOGNIZE

• ONLYPJL

• IGNORE

PATHSELECT • RECOGNIZE

• IGNORE

FUSERTEMP

• LOW

• MIDDLE

• HIGH

DENSITY

• LOW (MICRLOW)

• MIDDLE (MICRMIDDLE)

• HIGH, (MICRHIGH)

• ECOTOP

VERSHIFT • -50, -49, ....., -1, 0, 1, 2, ....., 50

HORSHIFT • -50, -49, ....., -1, 0, 1, 2, ....., 50

CUTSHIFT • -50, -49, ....., -1, 0, 1, 2, ....., 50

PERSONALITY • PCL

• HEXDUMP

AUTOFORMFEED • OFF, 1, 2, ....., 120

AUTOFORMCUT • OFF, 1, 2, ....., 120

TRACTORPOOL • ON,

• OFF

JOBSEPARATION • ON,

• OFF

13

2 List of Supported PJL Control Funcons

PJL SET VARIABLE VALUES

TRACTORCHANGECUT • ON,

• OFF

REPRINTLASTPAGE • ON,

• OFF

Note: All parameter which can be programmed with PJL Variables can also be congured by the

Operator Panel of the printer.

The following variables can be programmed by the PJL command:

• @PJL DEFAULT ”variable” = ”value”

PJL DEFAULT VARIABLE VALUES

POWERSAVE • OFF, 15, 30, 45, 60

KEEPTEMPHIGH • ALWAYS, 0.5, 1, ....., 60 (in steps of 0.5 sec)

ALARMBELL • ON,

• OFF

LANG

• ENGLISH

• GERMAN

• FRENCH

• SPANISH

MENUACCESS

• ALL

• PROFILESONLY

• NONE

Note: These variables can not be used by the PJL COMMAND SET.

14

3 List of Supported PCL5 Control Funcons

2.1.5 Supported PJL Variables and Values for PCL Personality

The following variables can be programmed by the PJL commands:

• @PJL SET LPARM : PCL ”variable” = ”value”

• @PJL DEFAULT LPARM : PCL ”variable” = ”value”

PJL VARIABLE VALUES

FONTNUMBER • 1, 2, 3, ....., 54

PITCH • 0.44, ....., 99.99 (in steps of 0.01)

SYMSET

• ROMAN8,

• ISOL1, ISOL2, ISO4, ISO6.ISOL5, ISOL9, SO11, ISO15, ISO17,

ISO21, ISO60, ISO69

• PC8, PC8DN, PC850, PC852, PC858, PC8TK

• WINL1, WINL2, WINL5, WIN30

• DESKTOP, PSTEXT,VNINTL, VNUS, MSPUBL

• MATH8, PSMATH, VNMATH, PIFONT, LEGAL,

LINESPACING • 1, 2, 3, ....., 48

TOPMARGIN • 0, 1, 2, ....., 999

LEFTMARGIN • 0, 1, 2, ....., 999

RIGHTMARGIN • 0, 1, 2, ....., 999, MAXIMUM

TEXTLENGTH • 0, 1, 2, ....., 999

PERFORATIONSKIP • OFF

• ON

DOLLARCOMMANDS • OFF

• ON

3 List of Supported PCL5 Control Funcons

3.1 Job Control Commands

JOB CONTROL COMMANDS VALUES

ESC % - 12345 X

• Universal Exit / Start of PJL

• Change to PJL Language Interpretaon Mode Reset

the printer like performing a Reset command

• Print all data received before the UEL command

15

3 List of Supported PCL5 Control Funcons

JOB CONTROL COMMANDS VALUES

ESC E

• Reset

• Reset to PJL Current Environment

• Prinng of any paral pages

• Deleng of all temporary download resources, as

macros, fonts, and paerns

ESC & l # X • Number of Copies

• Number of printed copies for each page

ESC & l # U

• Le Oset Registraon

• Posion of the logical page across the width of the

physical page

ESC & l # Z

• Top Oset Registraon

• Posion of the logical page along length of the phy-

sical page

ESC & u # D • Unit of Measure

• Measure for PCL unit cursor movements

ESC & l # G

(Private Command)

• Paper Exit Selecon

Parameters:

• # = 1 : Upper exit, each page is cut

• # = 2 : Lower exit (Stacker) without cung

• # = 12 : Lower exit, each page is cut

3.2 Page Control Commands

PAGE CONTROL

COMMANDS VALUES

ESC & l # A

(Private Command)

• Page Size

Denion of the paper size and in turn of the logical

page size. Parameters:

• # = 2 : Leer

• # = 26 : A4

• # = 101: Custom

ESC & l # O

• Orientaon

Dierent rotaons of the logical page

• # = 0: Portrait

• # = 1: Landscape

• # = 2: Reverse Portrait

• # = 3: Reverse Landscape

ESC & l # H

(Private Command)

• Paper Source

Designaon of the locaon for paper feeding or prinng

of the current page. Parameters:

• # = 0 : Print the current page

• # = 1 : Paper Feeding from the Upper Tractor

• # = 4 : Paper Feeding from the Lower Tractor

ESC & a # P

• Print Direcon

• Rotaon of the page coordinate system related to

the current posion in steps of 90°

16

3 List of Supported PCL5 Control Funcons

PAGE CONTROL

COMMANDS VALUES

ESC & a # L • Le Margin

• Seng to the le edge of the page (columns)

ESC & a # M • Right Margin

• Seng to the right edge of the page (columns)

ESC 9 • Clear Horizontal Margins

• Reseng of the right and le margin

ESC & l # E • Top Margin

• Seng the top of the text area in lines

ESC & l # F

• Text Length

• Number of prinng lines per page

• Seng of the boom margin

ESC & l # L

• Perforaon Skip

• # = 0 : Disable

• # = 1 : Enable

ESC & k # H • Horizontal Moon Index

• Width of the columns where # (x 1/120 inch)

ESC & l # C • Vercal Moon Index

• Height of rows where # (x 1/48 inch)

ESC & l # D

• Line Spacing

Number of lines printed per inch

• # = 1, 2, 3, ....., 48

3.3 Cursor Posioning Commands

CURSOR POSITIONING

COMMANDS VALUES

ESC & a # C • Horizontal Posion in Columns

ESC * p # X • Horizontal Posion in PCL Units

ESC & a # H • Horizontal Posion in Decipoints

ESC & a # R • Vercal Posion in Rows

ESC * p # Y • Vercal Posion in PCL Units

ESC & a # V • Vercal Posion in Decipoints

ESC = • Half Line Feed

ESC & k # G • Line Terminaon

ESC & f # S • Push / Pop Cursor Posion

17

3 List of Supported PCL5 Control Funcons

CURSOR POSITIONING

COMMANDS VALUES

ESC & k # G

• Line Terminaon

• # = 0 : CR = CR, LF = LF, FF = FF

• # = 1 : CR = CR+LF, LF = LF, FF = FF

• # = 2 : CR = CR, LF = CR+LF, FF = CR+FF

• # = 3 : CR = CR+LF, LF = CR+LF,

• FF = CR+FF

ESC & f # S

• Push / Pop Cursor Posion

• # = 0 : Push (Store)

• # = 0 : Pop (Recall)

ESC & s # C

• End-Of- Line Wrap

• # = 0 : Enable

• # = 1 : Disable

CR (hex 0D) • Carriage Return

SP (hex 20) • Space

BS (hex 08) • Backspace

HT (hex 09) • Horizontal Tab

LF (hex 0A) • Line Feed

FF (hex 0C) • Form Feed

3.4 Font Selecon Commands

FONT SELECTION

COMMANDS VALUES

ESC ( ID

• Symbol Set , primary *)

• ID = Code for Symbol Set, see Chapter 4

• Explanaon of Individual Items and here point SYM-

BOL SETS or a Printout of PCL TYPEFACE LIST

ESC ( s # P

• Spacing, primary *)

• # = 0 : Fixed Spacing

• # = 1 : Proporonal Spacing

ESC ( s # H • Pitch, primary *)

• # = Number of character per inch

ESC ( s # V • Height, primary *)

• # = Character height in point

ESC ( s # S

• Style, primary *)

• # = 0 : Upright

• # = 1 : Italic

ESC ( s # B

• Stroke Weight, primary *)

• # = 0 : Medium

• # = 3 : Bold

18

3 List of Supported PCL5 Control Funcons

FONT SELECTION

COMMANDS VALUES

ESC ( s # T

• Typeface, primary *)

• # = Code number for Typeface, see Printout of PCL

TYPEFACE LIST

ESC ( s # X • Font Selecon by ID #, primary *)

ESC ( 3 @ • Select Default Font as primary *)

*) All commands for primary with ?(? parenthesis can be used for secondary with ?)? parenthesis

3.5 Font Management Commands

FONT MANAGMENT

COMMANDS VALUES

ESC & d # D

• Enable Underline

• # = 0 : Fixed posion

• # = 3 : Floang posion

ESC & d @ • Disable Underline

ESC & p # X [data] • Transparent Print Data

ESC * c # D • Assign Font ID #

ESC * c # F • Font Control

ESC * c # R • User Dened Symbol Set ID Code

ESC ( f # W [data] • User Dened Symbol Set Data

ESC * c # S • User Dened Symbol Set Control

ESC ) s # W [data] • So Font Descriptor

ESC * c # E • So Font Character Code

ESC ( s # W [data] • So Font Download Character

ESC Y • Display Funcons Mode On

ESC Z • Display Funcons Mode O

Note: For detailled informaons see HP PCL 5 Technical Reference Manual.

19

3 List of Supported PCL5 Control Funcons

3.6 Macro control Commands

MACRO CONTROL

COMMANDS VALUES

ESC & f # Y • Macro ID

ESC & f # X

• Macro Control

• # = 0 : Start macro denion (last ID specied)

• # = 1 : Stop macro denion

• # = 2 : Execute macro (last ID specied)

• # = 3 : Call macro (last ID specied)

• # = 4 : Enable macro for automac overlay (last ID

specied)

• # = 5 : Disable automac overlay

• # = 6 : Delete all macros

• # = 7 : Delete all temporary macros

• # = 8 : Delete macro (last ID specied)

• # = 9 : Make macro temporary (last ID specied)

• # = 10 : Make marco permanent (last ID specied)

Note: For detailled informaons see HP PCL 5 Technical Reference Manual.

3.7 Graphic Commands

GRAPHIC

COMMANDS VALUES

ESC * v # N • Source Transparency Mode

ESC * v # O • Paern Transparency Mode

ESC * c # G • Area Fill ID

ESC * v # T • Select Current Paern

ESC * c # W [data] • Dene User Dened Paern

ESC * p # R • Set Paern Reference Point

ESC * c # Q • User Dened Paern Control

ESC * t # R • Raster Graphic Resoluon

ESC * r # F • Raster Graphic Presentaon

ESC * r # T • Raster Graphic Heigth

ESC * r # S • Raster Graphic Width

ESC * r # A • Start Raster Graphics

20

3 List of Supported PCL5 Control Funcons

GRAPHIC

COMMANDS VALUES

ESC * b # Y • Raster Graphic Y Oset

ESC * b # M • Raster Graphic Compression Mode

ESC * b # W [data] • Transfer Raster Graphic Data

ESC * B or ESC * C • End of Raster Graphic

ESC * c # A • Horizontal Rectangle Size, PCL Units

ESC * c # H • Horizontal Rectangle Size, Decipoint

ESC * c # B • Vercal Rectangle Size, PCL Units

ESC * c # V • Vercal Rectangle Size, Decipoints

ESC * c # G • Paern ID for Area Fill

ESC * c # P • Fill Rectangle Area

ESC * c # X • HPGL Horizontal Picture Frame Size

ESC * c # Y • HPGL Vercal Picture Frame Size

ESC * c 0 T • HPGL Picture Frame Anchor Point

ESC * c # K • HPGL Horizontal Plot Size

ESC * c # L • HPGL Vercal Plot Size

ESC % # B • Enter HPGL Mode

ESC % # A • Return from HPGL to PCL Mode

Note: For detailled informaons see HP PCL 5 Technical Reference Manual.

3.8 Status Readback Commands

STATUS READBACK

COMMANDS VALUES

ESC * s # T • Set Status Readback Locaon Type

ESC * s # U • Set Status Readback Locaon Unit

ESC * s # I • Set Status Readback Enty

La pagina sta caricando ...

PSI Laser Printer Programming Guide

PSI Laser Printer Programming Guide

in altre lingue

Altri documenti