Buffalo AirStation WLI-U2-KG54 Manuale utente

User Manual

Buffalo AirStation™

Wireless USB 2.0 Adapter

WLI-U2-KG54

www.buffalo-technology.com

2

Installation

Wireless USB 2.0 Adapter

Installation & Conﬁguration

1. Installing the Wireless USB 2.0 Adapter:

Insert the USB Adapter into your Laptop or Desktop PC as shown. USB ports

may be located on the rear, front or side of your PC depending on the design.

If there are multiple ports, choose the port that is free of interference to

maximize antenna reception.

3

2. Device Discovery:

Once inserted, Windows will automatically discover the presence of new

hardware. Various popup clouds will appear from the Windows taskbar.

During this time, allow Windows and the Wireless USB Adapter to communicate.

The process should take about one minute.

Click Next if the Found New Hardware Wizard appears as shown above.

Installation

4

Installation

3. Wireless Adapter Driver Installation:

In Windows XP or 2000, the following dialog box may appear as drivers are

installed. If so click Yes or Continue Anyway to ﬁnish installing the necessary

drivers.

Windows 98SE/ME/2000 users should skip to page 9.

5

Completing Installation on Windows XP

4. Completing Driver Installation for Windows XP:

When the driver has completed installing on a Windows XP PC click Finish.

If you wish to use Windows Wireless Zero Conﬁguration Service click No on the

next dialog box and go on to page 6. Otherwise, click Yes on the dialog box to

install Buffalo’s Client Manager and go on to page 10.

6

3. Conﬁguring Wireless Zero Conﬁguration

Service:

If the Wireless Zero Conﬁguration Service

is activated, Windows will scan for available

wireless access points once the Wireless PCI

Adapter is properly installed. If Windows detects

one or more access points, a networking icon

appears on the task bar. One or more wireless

networks are available appears as a caption

accompanying the icon.

Note: If the Wireless Zero Conﬁguration

Service is not functioning, select Start>Control

Panel>Administrative Tools>Services. Select

Automatic in the Startup Type ﬁeld of Wireless

Zero Conﬁguration Service to enable the

Wireless Zero Conﬁguration Service. The default

value of Wireless Zero Conﬁguration Service is

Automatic.

Right click the networking icon in the taskbar and

select View Available Wireless Networks to display

a list of available wireless networks. Select an

access point network name and click the Connect

button to establish a connection. You may need

to check the box indicating you are connecting

to an unsecured network. See Page 7 if you need

to enter an SSID network name or WEP/WPA

encryption key.

Using Wireless Zero Conﬁguration Service

7

Click the Advanced button to enter an SSID network name or WEP/WPA

encryption key, if either is necessary. To add an SSID network name that is

not available, click the Add button.

Using Wireless Zero Conﬁguration Service

8

Using Wireless Zero Conﬁguration Service

To conﬁgure a WEP/WPA encryption key, select

the appropriate wireless network and click the

Conﬁgure button.

From the pull down menu, select the appropriate

Network Authentication and Data Encryption for the

wireless network. Enter and conﬁrm the Network

Key and Key Index. Click the OK button when

ﬁnished.

Note: Buffalo Technology recommends that

users of the Wireless Zero Conﬁguration Service

upgrade to the latest version freely available at:

http://www.microsoft.com.

For advanced support in using Window’s XP’s

Wireless Zero Conﬁguration Service, refer to

the Buffalo Support Web Site: http://www.buffalo-

technology.com

Skip to Page 12 if you are not using Windows XP or prefer not to use Windows

XP's Wireless Zero Configuration Service.

9

Completing Installation on Windows 98SE/ME/2000

4. Completing Driver Installation for Windows 98SE/ME/2000:

When the driver has completed installing on a Windows XP PC click Finish.

Click Yes on the new dialog box that will appear to install Buffalo’s Client

Manager.

10

Client Manager

Use Client Manager to conﬁgure your wireless network. Use Client Manager

to survey and connect to available access points, enable and use WEP/WPA

encryption, and create connection proﬁles.

Note: Client Manager does not function properly if the Windows XP Wireless

Zero Conﬁguration Service is enabled.

Installing Client Manager

Once the InstallShield Wizard launches, click the Next button to begin the

software installation.

Client Manager

11

Client Manager

Once the Installer Wizard launches, click the Next button to begin the software stallation.

Press I Agree to accept the license agreement and continue the installation process.

12

Client Manager

Press the OK button to ﬁnish and close

the installation program.

Press the Exit button to exit the Client Manager installation utility.

◗ The Buffalo Client Manager is now installed and running, right clicking on its

icon (the black notebook icon) will allow you to begin using it.

13

Client Manager Conﬁguration

Use Client Manager to conﬁgure your wireless network. To assist in conﬁguring your

wireless network, Client Manager consists of the Status page, the Survey page, and

the Proﬁles page. You can access each page by clicking the corresponding button

on Client Manager. In addition to these pages, several dialog boxes are available to

meet specialized conﬁguration needs. You can access the Edit Proﬁle dialog box,

New Proﬁle dialog box, IP Conﬁguration dialog box, or WEP Conﬁguration dialog box

using the Client Manager pages.

Status Page

Click the Status button to open this page.

By default, this page is displayed when

you start Client Manager. This page

displays the status of the connection

between the wireless adapter and

another wireless device. This page only

displays connection information no

changes to the connection can be made

from this screen.

This page includes the following

components:

• Network Type – Displays what mode

the network device is in. Ad-Hoc or

Infrastructure are the available modes.

Client Manager Conﬁguration

14

Client Manager Conﬁguration

• Rate – The speed that the two wireless clients are communicating at. If the

Client Manager is not connected to a remote wireless device (access point or

another client) then no rate will be displayed.

• Channel – The channel that the two wireless clients are communicating at.

If the Client Manager is not connected to a remote wireless device (access

point of another client) then no channel will be displayed. The available

channels for use are 1-11.

• Security– The type of encryption that the two wireless clients are

communicating with. If the Client Manager is not connected to a remote

wireless device (access point of another client) then ‘No Encryption’ will be

displayed.

• IP Address – The IP address of the machine the Client Manager is installed on.

If the Client Manager is not connected to a remote wireless device (access

point of another client) or is not connected to a network with DHCP, then no

IP address will be displayed.

• MAC Address – The MAC address of the wireless client device inside the

computer Client Manager is installed on. If no wireless device is present in

the computer, then no MAC Address will be displayed.

• Signal Strength – Displays the strength of the signal. Signal Strength is based on

the peak signal level the wireless adapter receives from the wireless device

to which it is connected. Next to the signal level is the wireless hardware

type that the computer has available.

15

Client Manager Conﬁguration

Survey Page

Click the Survey button to open this page. Use this page to survey the area,

display available access points, and connect to available access points.

This page includes the following

components:

• Wireless SSID – Displays the SSID

associated with each available

access point. The SSID is the

unique network name that functions

as an identiﬁer for your wireless

devices. All wireless devices on a

network must use identical SSIDs

to successfully associate with other

devices on the network. buffalo_test

is an example of a valid SSID.

• Mode – Displays the mode/rate set that

the remote wireless device is offering.

• Key – Displays whether the wireless network is using any sort of encryption.

Press the ‘Connect’ button to connect to a listed SSID, or press the ‘Refresh’

button to perform another survey and update the survey list.

16

Client Manager Conﬁguration

Once the ‘Connect’ button is pressed, you will be prompted to enter any

encryption related information.

The ‘Acquire IP automatically’ checkbox

tells the client device to obtain an IP

automatically from a DHCP server. This is

the recommended setting.

The ‘Encryption’ drop down list allows you

to select the type of encryption for the

network. By default the proper encryption

type should already be selected. In the

event that no encryption is used, leave the

‘No Encryption’ option selected.

by the wireless network must be inputted. Please consult your wireless access

point or router’s documentation for proper input of the encryption keys. Some

wireless networks may require you to enter multiple keys, in this event, four

separate ﬁelds are available for encryption keys.

The ‘Save settings as a proﬁle’ option will store this wireless network in your

proﬁles. This means you will automatically connect to this network when

inside its range. This settings is recommended if you plan on using this

wireless network more than once.

17

Proﬁles Page

Click the Proﬁles button to open this

page. Use this page to access your

proﬁles. Proﬁles allow you to save

the information associated with a

speciﬁc wireless network so you

can quickly and easily connect to

that network when you are in that

location. The Proﬁles page allows

you to add, delete, and edit your

proﬁles, as well as import and export

data.

• Connect – Click the Connect button to

connect to the selected proﬁle and

return to the ‘Status’ page.

• Edit – Click the Edit button to edit the selected proﬁle’s settings. The Edit

button also allows you to delete a proﬁle no longer used or required.

• Add – Click the Add button to add a proﬁle manually. You will need important

information such as SSID, encryption settings, and network type.

Client Manager Conﬁguration

18

New Proﬁle Dialog Box

Use this dialog box to create a new proﬁle.

Client Manager Conﬁguration

• Proﬁle Name – Enter the name you want to

associate with the new proﬁle.

• Network Type – Select the network mode you

want to associate with the new proﬁle. Select

Infrastructure if your network consists of both

wired and wireless devices that communicate

through a central device, such as an access

point. Select Ad-hoc if your network consists of

only wireless devices that communicate with

each other directly.

• Network Name SSID – Enter the SSID of your

must use identical SSIDs to successfully associate with other devices on the

network. myssid is an example of a valid SSID.

• Channel – Displays the channel associated with the new proﬁle. The channel

indicates what range of frequencies the radio waves emitted by the wireless

device are occupying. Devices that meet 802.11b and 802.11g standards can

use channels 1-11 within the 2.4 GHz spectrum.

• Encryption Type – Displays the types of encryptions available. Once selected,

you will be required to enter the Encryption Key Number and the Encryption Key

as well. For the Encryption Key Number, it is recommended to use 1 unless

speciﬁed to by an administrator.

19

Client Manager Conﬁguration

Advanced Proﬁle Options

• Network Tab – Displays the network information tab. A static IP can be

speciﬁed for this wireless proﬁle here. It is not recommended to change any

of these settings unless speciﬁed by an administrator.

• Browser Tab – Displays settings to change your browser preferences for this

wireless proﬁle. A speciﬁc home page can be speciﬁed when connected to

this wireless proﬁle as can speciﬁc proxy server addresses.

• Printers Tab – Displays the printers tab. A speciﬁc default printer can be

associated to this proﬁle. Thus, when connected to this proﬁle, a speciﬁc

printer will be used as the default printer.

• Network Tab – Displays the network information tab. A static IP can be

speciﬁed for this wireless proﬁle here. It is not recommended to change any

of these settings unless speciﬁed by an administrator.

• OK – Click the OK button to save your speciﬁcations and return to the Proﬁles

page.

• AOSS Icon – The AOSS icon is used to launch AOSS client requests

for AOSS communication. Inside your wireless client’s box, an

AOSS supplement guide is present. This guide leads to step-by-

step instructions on using the AOSS icon.

20

Wireless Zero Conﬁguration

Wireless Zero Conﬁguration Service (Windows XP)

Windows XP offers the Wireless Zero Conﬁguration Service to support 802.11b

and 802.11g wireless networking. This service automatically polls the area for

available wireless access points. If an available wireless access point is found,

Windows attempts to connect to the access point. If no available wireless

access points are found, you must manually add the access points.

Note: The Wireless Zero Conﬁguration Service and Client Manager do not

function properly together. If you want to use Client Manager, you must disable

the Wireless Zero Conﬁguration Service.

Enabling the Wireless Zero Conﬁguration Service

Select Start»Control Panel»Administrative Tools»Services to open the Services

window. Select Automatic in the Startup Type ﬁeld of Wireless Zero Conﬁguration

Service to enable the Wireless Zero Conﬁguration Service.

Note: The default Startup Type value of Wireless Zero Conﬁguration Service is

Automatic.

Disabling the Wireless Zero Conﬁguration Service

Select Start»Control Panel»Administrative Tools»Services to open the Services

window. Select Disabled in the Startup Type ﬁeld of Wireless Zero Conﬁguration

Service to disable the Wireless Zero Conﬁguration Service.

La pagina sta caricando ...

Buffalo AirStation WLI-U2-KG54 Manuale utente

Questo manuale è adatto anche per

Buffalo AirStation WLI-U2-KG54 Manuale utente

in altre lingue

Documenti correlati

Altri documenti