Abit Fatal1ty F-190HD Manuale utente

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

F-I90HD

Motherboard

Socket 775

User’s Manual

For more information:

www.abit.com.tw

 LGA775 Micro ATX

 NB: ATI Radeon Xpress 1250

SB: ATI SB600

 1066/800MHz FSB

 Dual Channel DDR2

800/667/533

 ATI Radeon Xpress 1250

Integrated Graphics

 PCI Express Slot

 HDMI Support

 PCIE Gigabit LAN

 4x SATA 3Gb/s RAID

 7.1-Channel HD Audio

ii F-I90HD

F-I90HD

User’s Manual

English + Multilingual QIG

P/N: 4310-0000-83

Rev. 2.00, April 2007

Copyright and Warranty Notice

The information in this document is subject to change without notice and does not represent a

commitment on part of the vendor, who assumes no liability or responsibility for any errors that may

appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality,

accuracy or fitness for any particular part of this document. In no event shall the manufacturer be

liable for direct, indirect, special, incidental or consequential damages arising from any defect or

error in this manual or product.

Product names appearing in this manual are for identification purpose only and trademarks and

product names or brand names appearing in this document are the property of their respective

owners.

No part of this manual may be reproduced, transmitted or transcribed without the expressed written

permission of the manufacturer and authors of this manual.

If you do not properly set the motherboard settings, causing the motherboard to malfunction or fail,

we cannot guarantee any responsibility.

The Fatal1ty name, Fatal1ty logos and the Fatal1ty likeness are trademarks of Fatal1ty,

All other trademarks are the property of their respective owners.

The Following Information is Only for EU-member States:

Directive 2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE): The use of the symbol indicates that this product may not be

treated as household waste. By Ensurin

g

this product is disposed of correctly,

you will help prevent potential ne

g

ative consequences for the environment

and human health, which could otherwise be cause by inappropriate waste

handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal

service or the shop where you purchased the product.

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

F-I90HD iii

Introduction

FATAL1TY STORY

Who knew that at age 19, I would

be a World Champion PC gamer.

When I was 13, I actually played

competitive billiards in professional

tournaments and won four or five

games off guys who played at the

highest level. I actually thought of

making a career of it, but at that

young age situations change rapidly.

Because I’ve been blessed with

great hand-eye coordination and a

grasp of mathematics (an important

element in video gaming) I

gravitated to that activity.

GOING PRO

I started professional gaming in 1999 when I entered the CPL (Cyberathlete Professional

League) tournament in Dallas and won $4,000 for coming in third place. Emerging as one of

the top players in the United States, a company interested in sponsoring me flew me to Sweden

to compete against the top 12 players in the world. I won 18 straight games, lost none, and

took first place, becoming the number one ranked Quake III player in the world in the process.

Two months later I followed that success by traveling to Dallas and defending my title as the

world’s best Quake III player, winning the $40,000 grand prize. Since then I’ve traveled the

globe to compete against the best in the world, winning prizes and acclaim, including the 2005

CPL World Tour Championship in New York City for a $150,000 first place finish.

LIVIN’ LARGE

Since my first big tournament wins, I have been a “Professional Cyberathlete”, traveling the

world and livin’ large with lots of International media coverage on outlets such as MTV, ESPN

and G4TV to name only a few. It's unreal - it's crazy. I’m living a dream by playing video

games for a living. I’ve always been athletic and took sports like hockey and football very

seriously, working out and training hard. This discipline helps me become a better gamer and

my drive to be the best has opened the doors necessary to become a professional.

A DREAM

Now, another dream is being realized – building the ultimate gaming computer, made up of the

best parts under my own brand. Quality hardware makes a huge difference in competitions…a

couple more frames per second and everything gets really nice. It's all about getting the

computer processing faster and allowing more fluid movement around the maps.

My vision for Fatal1ty hardware is to allow gamers to focus on the game without worrying

about their equipment, something I’ve preached since I began competing. I don’t want to

worry about my equipment. I want it to be there – over and done with - so I can focus on the

game. I want it to be the fastest and most stable computer equipment on the face of the

planet, so quality is what Fatal1ty brand products will represent.

iv F-I90HD

FATAL1TY PARTNERS

This is just the beginning. We’re already in development for several new products, and I’m

really grateful to all my Fatal1ty partners for helping make my dreams a reality.

I know there is a business side to all of this, but for me the true reward is making products that

are so good I can win with them – and making them available to fellow gamers. Gaming is my

life, and many fellow gamers around the world are also some of my best friends, so giving back

to the gaming community is really important to me.

Johnathan “Fatal1ty” Wendel

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

F-I90HD v

Contents

1. Hardware Setup ............................................................... 1-1

1.1 Specifications............................................................................... 1-1

1.2 Motherboard Layout ..................................................................... 1-2

1.3 Choosing a Computer Chassis ....................................................... 1-3

1.4 Installing Motherboard ................................................................. 1-3

1.5 Checking Jumper Settings............................................................. 1-4

1.5.1 CMOS Memory Clearing Header and Backup Battery .............. 1-4

1.6 Connecting Chassis Components ................................................... 1-6

1.6.1 ATX Power Connectors......................................................... 1-6

1.6.2 Front Panel Switches & Indicators Headers ........................... 1-7

1.6.3 FAN Power Connectors ........................................................ 1-7

1.7 Installing Hardware...................................................................... 1-8

1.7.1 CPU Socket 775................................................................... 1-8

1.7.2 DDR2 Memory Slots........................................................... 1-10

1.8 Connecting Peripheral Devices .................................................... 1-11

1.8.1 Floppy and IDE Disk Drive Connectors ................................ 1-11

1.8.2 Serial ATA Connectors ....................................................... 1-12

1.8.3 Additional USB 2.0 Port Headers......................................... 1-13

1.8.4 Internal Audio Connector ................................................... 1-14

1.8.5 Front Panel Audio Connection Header ................................. 1-14

1.8.6 PCI and PCI Express X16, X1 Slots ..................................... 1-16

1.8.7 TV-OUT Header................................................................. 1-16

1.9 Onboard Indicators and Buttons.................................................. 1-17

1.9.1 LED Indicators................................................................... 1-17

1.10 Connecting Rear Panel I/O Devices ........................................... 1-18

2. BIOS Setup....................................................................... 2-1

2.1 SoftMenu Setup ........................................................................... 2-2

2.2 Standard CMOS Features.............................................................. 2-3

2.3 Advanced BIOS Features .............................................................. 2-6

2.4 Advanced Chipset Features........................................................... 2-9

2.5 Integrated Peripherals................................................................ 2-10

2.6 Power Management Setup .......................................................... 2-13

2.7 PnP/PCI Configurations .............................................................. 2-15

2.8 PC Health Status ........................................................................ 2-16

2.9 Load Fail-Safe Defaults............................................................... 2-18

2.10 Load Optimized Defaults........................................................... 2-18

2.11 Set Password ........................................................................... 2-18

2.12 Save & Exit Setup..................................................................... 2-18

2.13 Exit Without Saving .................................................................. 2-18

3. Driver & Utility ................................................................. 3-1

3.1 CD-ROM AUTORUN ...................................................................... 3-1

vi F-I90HD

3.2 ATi South Bridge Driver ................................................................ 3-2

3.3 Microsoft.NET Framework............................................................. 3-2

3.4 ATi VGA Driver............................................................................. 3-3

3.5 Realtek LAN Driver....................................................................... 3-3

3.6 Realtek Audio Driver (ATi HDMI)................................................... 3-4

3.7 ATi RAID Driver ........................................................................... 3-6

3.8 USB 2.0 Driver ............................................................................. 3-6

3.9 abit EQ........................................................................................ 3-7

3.10 FlashMenu (BIOS Update Utility) ................................................. 3-8

3.11 SATA RAID Driver (for Windows Vista) ........................................ 3-9

3.12 SATA RAID Driver (for Windows XP, 2003, or 2000) ..................... 3-9

4. Multilingual Quick Installation Guide .............................. 4-1

4.1 Français//Guide d'Installation Rapide............................................. 4-1

4.2 Deutsch//Kurze Installationsanleitung............................................ 4-2

4.3 Italiano//Guida all’installazione rapida ........................................... 4-3

4.4 Español//Guía rápida de instalación............................................... 4-4

4.5 Português//Guia de instalação rápida ............................................ 4-5

4.6 Русский//Краткое руководство по установке .............................. 4-6

4.7 Eesti//Kiirpaigaldusjuhend ............................................................ 4-7

4.8 Latviski//Ātrās instalēšanas instrukcija........................................... 4-8

4.9 Lietuvių//Trumpas instaliavimo vadovas ........................................ 4-9

4.10 Polski//Instrukcja szybkiej instalacji........................................... 4-10

4.11 Magyar//Gyorstelepítési útmutató.............................................. 4-11

4.12 Türkçe//Hızlı Kurulum Kılavuzu.................................................. 4-12

4.13 اللغة العربية//دليل التركيب السريع....................... 4-13

4.14 فارسی// راﻩنمای نصب سریع............................................... 4-14

4.15 日本語//クイックインストールガイド ...................................... 4-15

4.16 한국어//빠른 설치 가이드 ....................................................... 4-16

4.17 Bahasa Malaysia//Panduan Pemasangan Ringkas ....................... 4-17

4.18 ไทย//คู่มือการติดตั้งอย่างย่อ ........................................................ 4-18

4.19 繁體中文................................................................................. 4-19

4.19.1 規格............................................................................... 4-19

4.19.2 快速安裝略說.................................................................. 4-20

4.20 简体中文................................................................................. 4-21

4.20.1 规格 ............................................................................... 4-21

4.20.2 快速安装略说.................................................................. 4-22

5. Appendix .......................................................................... 5-1

5.1 Troubleshooting (How to Get Technical Support?).......................... 5-1

5.1.1 Q & A ................................................................................. 5-1

5.1.2 Technical Support Form....................................................... 5-4

5.1.3 Contact Information............................................................. 5-5

Hardware Setup

F-I90HD 1-1

1. Hardware Setup

1.1 Specifications

CPU

• Designed for Intel Dual Core LGA775

processor with 1066/800MHz FSB

• Support Intel Core 2 Extreme, Core 2

Quad, Core 2 Duo, Pentium EE,

Pentium D, Pentium Dual Core, and

Pentium 4 Processor

Chipset

• NB: ATI Radeon Xpress 1250

• SB: ATI SB600

Memory

• 4x 240-pin DIMM slots support

maximum memory capacity up to 16GB

• Supports Dual Channel DDR2

800/667/533 Un-buffered ECC/Non-ECC

memory

Graphics

• ATI Radeon Xpress 1250 on-chip

(Radeon X700-based 2D/3D graphics)

HDMI

• Support HDMI

• Support High Definition Video Output

• Support 7.1-channel HD audio

LAN

• Onboard PCIE Gigabit LAN

Audio

• Onboard 7.1-channel HD audio

Serial ATA

• 4x SATA 3Gb/s supports SATA RAID 0,

1, and 0+1

Expansion Slots

• 1x PCI-E X16 slot

• 2x PCI-E X1 slots

• 1x PCI slot

Internal I/O Connectors

• 1x Floppy port

• 1x Ultra ATA 133 IDE connector

• 4x SATA 3Gb/s connectors

• 3x USB 2.0 headers

• 1x FP-Audio header

• 1x CD-In connector

• 1x TV-OUT header

Rear Panel I/O

• 1x PS/2 Keyboard connector

• 1x PS/2 Mouse connector

• 1x VGA connector

• 1x HDMI connector

• 1x Optical S/PDIF Out connector

• 1x 7.1-channel Audio connector

• 4x USB 2.0 connectors

• 1x RJ-45 Gigabit LAN connector

abit Engineered

• abit SoftMenu

™

Technology

RoHS

• 100% Lead-free process and RoHS

compliant

Miscellaneous

• Micro ATX form factor (244mm x

244mm)

※ Specifications and information contained herein are subject to change without

notice.

1-2 F-I90HD

1.2 Motherboard Layout

Hardware Setup

F-I90HD 1-3

1.3 Choosing a Computer Chassis

• Choose a chassis big enough to install this motherboard.

• As some features for this motherboard are implemented by cabling connectors on the

motherboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is a possibility of adopting some more hard drives, make sure your chassis has

sufficient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port configuration of this motherboard. You can find

an I/O shield specifically designed for this motherboard in its package.

1.4 Installing Motherboard

Most computer chassis have a base with many

mounting holes to allow the motherboard to be

securely attached, and at the same time, prevent

the system from short circuits. There are two

ways to attach the motherboard to the chassis

base: (1) with studs, or (2) with spacers.

Basically, the best way to attach the board is

with studs. Only if you are unable to do this

should you attach the board with spacers. Line up the holes on the board with the mounting

holes on the chassis. If the holes line up and there are screw holes, you can attach the board

with studs. If the holes line up and there are only slots, you can only attach with spacers. Take

the tip of the spacers and insert them into the slots. After doing this to all the slots, you can

slide the board into position aligned with slots. After the board has been positioned, check to

make sure everything is OK before putting the chassis back on.

※ Always power off the computer and unplug the AC power cord before adding or

removing any peripheral or component. Failing to so may cause severe damage

to your motherboard and/or peripherals. Plug in the AC power cord only after

you have carefully checked everything.

To install this motherboard:

1. Locate all the screw holes on the

motherboard and the chassis base.

2. Place all the studs or spacers needed on

the chassis base and have them tightened.

3. Face the motherboard’s I/O ports toward

the chassis’s rear panel.

4. Line up all the motherboard’s screw holes

with those studs or spacers on the chassis.

5. Install the motherboard with screws and

have them tightened.

※ To prevent shorting the PCB circuit,

please REMOVE the metal studs or

spacers if they are already fastened

on the chassis base and are without

mounting-holes on the motherboard

to align with.

Face the chassis’s rear panel.

1-4 F-I90HD

1.5 Checking Jumper Settings

• For a 2-pin jumper, plug the

jumper cap on both pins will

make it CLOSE (SHORT).

Remove the jumper cap, or

plug it on either pin

(reserved for future use) will

leave it at OPEN position.

SHORT OPEN

OPEN

• For 3-pin jumper, pin 1~2 or pin 2~3 can be

shorted by plugging the jumper cap in.

Pin 1~2 SHORT

Pin 2~3 SHORT

1.5.1 CMOS Memory Clearing Header and Backup Battery

The time to clear the CMOS memory occurs when (a)

the CMOS data becomes corrupted, (b) you forgot the

supervisor or user password preset in the BIOS menu,

(c) you are unable to boot-up the system because the

CPU ratio/clock was incorrectly set in the BIOS menu,

or (d) whenever there is modification on the CPU or

memory modules.

This header uses a jumper cap to clear the CMOS

memory and have it reconfigured to the default values

stored in BIOS.

• Pins 1 and 2 shorted

(Default): Normal

operation.

• Pins 2 and 3 shorted:

Clear CMOS memory.

To clear the CMOS memory and load in the default values:

1. Power off the system.

2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper

cap back to its default settings --- pin 1 and pin 2 shorted.

3. Power on the system.

4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS

setup menu right after powering on system.

5. Set the CPU operating speed back to its default or an appropriate value.

6. Save and exit the BIOS setup menu.

Hardware Setup

F-I90HD 1-5

CMOS Backup Battery:

An onboard battery saves the CMOS memory to keep the BIOS information stays on even after

disconnected your system with power source. Nevertheless, this backup battery exhausts after

some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS

checksum error” displays on monitor, this backup battery is no longer functional and has to

be renewed.

To renew the backup battery:

1. Power off the system and disconnect with AC power source.

2. Remove the exhausted battery.

3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its

positive polarity.

4. Connect AC power source and power on the system.

5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.

CAUTION:

※ Danger of explosion may arise if the battery is incorrectly renewed.

※ Renew only with the same or equivalent type recommended by the battery

manufacturer.

※ Dispose of used batteries according to the battery manufacturer’s instructions.

1-6 F-I90HD

1.6 Connecting Chassis Components

1.6.1 ATX Power Connectors

These connectors provide the connection from an ATX power supply. As the plugs from the

power supply fit in only one orientation, find the correct one and push firmly down into these

connectors.

ATXPWR1: ATX 24-Pin Power Connector

The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector.

Connect from pin-1 for either type. However, a 20-pin power supply may cause the system

unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W

or higher is recommended.

ATX12V1: ATX 12V 4-Pin Power Connector

This connector supplies power to CPU. The system will not start without connecting power to

this one.

Hardware Setup

F-I90HD 1-7

1.6.2 Front Panel Switches & Indicators Headers

This header is used for connecting switches and

LED indicators on the chassis front panel.

Watch the power LED pin position and orientation.

The mark “+” align to the pin in the figure below

stands for positive polarity for the LED connection.

Please pay attention when connecting these

headers. A wrong orientation will only result in the

LED not lighting, but a wrong connection of the

switches could cause system malfunction.

• HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis

front panel.

• RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis

front panel.

• SPKR (Pin 13, 15, 17, 19):

Connects to the System Speaker cable of

chassis.

• SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there

is one) of chassis front panel.

• PWR (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

• PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

1.6.3 FAN Power Connectors

These connectors each provide power to the

cooling fans installed in your system.

• CPUFAN1: CPU Fan Power Connector

• SYSFAN1: System Fan Power

Connector

• AUXFAN1~2: Auxiliary Fan Power

Connector

.

※ These fan connectors are not

jumpers. DO NOT place jumper

caps on these connectors.

1-8 F-I90HD

1.7 Installing Hardware

※ DO NOT scratch the motherboard when installing hardware. An accidental

scratch of a tiny surface-mount component may seriously damage the

motherboard.

※ In order to protect the contact pins, please pay attention to these notices:

1. A maximum 20 cycles of CPU installation is recommended.

2. Never touch the contact pins with fingers or any object.

3. Always put on the cap when the CPU is not in use.

1.7.1 CPU Socket 775

※ The installation procedures vary with different types of CPU fan-and-heatsink

assembly. The one shown here is served for demo only. For detailed

information on how to install the one you bought, refer to its installation

guidelines.

1. Place the board so that the lever-hook of

the socket is on your left side. Use your left

thumb and forefinger to hold the lever hook,

pull it away from the retention tab. Rotate

the lever to fully open position.

2. Use your right-thumb to raise the load

plate. Lift it up to fully open position.

3. Use your right thumb and forefinger to

grasp the CPU package. Be sure to grasp on

the edge of the substrate, and face the Pin-1

indicator toward the bottom-left side. Aim at

the socket and place the CPU package

vertical down into the socket.

4. Visually inspect if the CPU is seated well

into the socket. The alignment key must be

located in the notch of package.

Hardware Setup

F-I90HD 1-9

5. Use your left hand to hold the load plate,

and use your right thumb to peel the cap off.

The cap plays an important role in

protecting contact pins. In order to

prevent bent pin, PUT ON the cap after

operation or testing.

6. Lower the plate onto the CPU package.

Engage the load lever while gently pressing

down the load plate.

7. Secure the lever with the hook under

retention tab.

8. Place the heatsink and fan assembly onto

the socket. Align the four fasteners toward

the four mounting holes on the motherboard.

9. Press each of the four fasteners down

into the mounting holes. Rotate the fastener

clock-wise to lock the heatsink and fan

assembly into position.

10. Attach the four-pin power plug from the

heatsink and fan assembly to the CPU FAN

connector.

※ A higher fan speed will be helpful for better airflow and heat-dissipation.

Nevertheless, stay alert to not touch any heatsink since a high temperature

generated by the working system is still possible.

1-10 F-I90HD

1.7.2 DDR2 Memory Slots

To reach the performance of Dual Channel DDR2, the following rules must be obeyed:

• For a 2-DIMM dual-channel installation:

Populate DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], or slots

[DIMM2]+[DIMM4].

• For a 4-DIMM dual-channel installation:

Populate 2 DIMM modules of the same type and size on slots [DIMM1]+[DIMM3], and

another 2 DIMM modules of the same type and size on slots [DIMM2]+[DIMM4].

※ [DIMM1] and [DIMM3] slots are made of the same color.

[DIMM2] and [DIMM4] are made of another same color.

※ Usually there is no hardware or BIOS setup required after adding or removing

memory modules, but you will have to clear the CMOS memory first if any

memory module related problem occurs.

※

This motherboard does not support DDR2 memory modules of X4 device

width.

To install system memory:

1. Power off the computer and unplug the

AC power cord before installing or

removing memory modules.

2. Locate the DIMM slot on the board.

3. Hold two edges of the DIMM module

carefully, keep away from touching its

connectors.

4. Align the notch key on the module with

the rib on the slot.

5. Firmly press the module into the slots until the ejector tabs at both sides of the slot

automatically snap into the mounting notch. Do not force the DIMM module in with extra

force as the DIMM module only fits in one direction.

6. To remove the DIMM modules, push the two ejector tabs on the slot outward

simultaneously, and then pull out the DIMM module.

※ Static electricity can damage the electronic components of the computer or

optional boards. Before starting these procedures, ensure that you are

discharged of static electricity by touching a grounded metal object briefly.

Hardware Setup

F-I90HD 1-11

1.8 Connecting Peripheral Devices

1.8.1 Floppy and IDE Disk Drive Connectors

The FDC1 connector connects up to two floppy drives with a 34-wire, 2-connector floppy cable.

Connect the single end at the longer length of ribbon cable to the FDC1 on the board, the two

connectors on the other end to the floppy disk drives connector. Generally you need only one

floppy disk drive in your system.

※ The red line on the ribbon cable must be aligned with pin-1 on both the FDC1

port and the floppy connector.

Each of the IDE port connects up to two IDE drives

at Ultra ATA/100 mode by one 40-pin, 80-conductor,

and 3-connector Ultra ATA/66 ribbon cables.

Connect the sin

g

le end (blue connector) at the lon

g

er

length of ribbon cable to the IDE port of this board,

the other two ends (gray and black connector) at the

shorter length of the ribbon cable to the connectors

of your hard drives.

※ Make sure to configure the “Master” and “Slave” relation before connecting

two drives by one single ribbon cable. The red line on the ribbon cable must be

aligned with pin-1 on both the IDE port and the hard-drive connector.

1-12 F-I90HD

1.8.2 Serial ATA Connectors

Each SATA connector serves as one single channel to connect one SATA device by SATA cable.

The RAID 0/1/0+1 configuration is also possible by the combination of disk arrays through

these SATA connectors:

For more information on how to configure the function mode for SATA, please refer to the item

“OnChip SATA Mode” in the BIOS setup menu of “OnChip IDE Device”.

To connect SATA device:

1. Attach either end of the signal cable

to the SATA connector on

motherboard. Attach the other end to

the SATA device.

2. Attach the SATA power cable to the

SATA device and connect the other

end from the power supply.

※ The motherboard in this photo is served for DEMO only, and may not be the

same type or model as the one described in this user’s manual.

Hardware Setup

F-I90HD 1-13

1.8.3 Additional USB 2.0 Port Headers

Each header supports 2x additional USB 2.0 ports by connecting bracket or cable to the rear I/O

panel or the front-mounted USB ports of your chassis.

Pin Pin Assignment Pin Pin Assignment

1 VCC 2 VCC

3 Data0 - 4 Data1 -

5 Data0 + 6 Data1 +

7 Ground 8 Ground

10 NC

※ Make sure the connecting cable bears the same pin assignment.

1-14 F-I90HD

1.8.4 Internal Audio Connector

This connector connects to the audio output of internal CD-ROM drive or add-on card.

1.8.5 Front Panel Audio Connection Header

This header provides the front panel connection for HD (High Definition)

Audio, yet for AC’97 Audio CODEC connection, you must carefully check the

pin assignment before connecting from the front panel module. An incorrect

connection may cause malfunction or even damage the motherboard.

※ Please do not connect the “Ground” cable or “USB VCC” cable

from the front panel module to the Pin 4 “AVCC” of this header.

Pin Assignment

(HD AUDIO)

Pin Assignment

(AC’97 AUDIO)

1 MIC2 L 1 MIC In

2 AGND 2 GND

3 MIC2 R 3 MIC Power

4 AVCC 4NC

5 FRO-R 5 Line Out (R)

6 MIC2_JD 6 NC

7F_IO_SEN 7 NC

9 FRO-L 9 Line Out (L)

10 LINE2_JD 10 NC

La pagina sta caricando ...

Abit Fatal1ty F-190HD Manuale utente

Questo manuale è adatto anche per

Abit Fatal1ty F-190HD Manuale utente

in altre lingue

Documenti correlati

Altri documenti