Nortel Networks 2382 Manuale utente

Marca: Nortel Networks

Modello: 2382

Tipo: Manuale utente

Questo manuale è adatto anche per

Nortel WLAN—Security Switch 2300 Series

Document number: NN47250-300

Document status: Standard

Document version: 02.01

Part Code: 320655-E

Release Date: October 2007

Nortel WLAN - Security Switch 2300 Series

Quick Start Guide

NN47250-300 (320655-E Version 02.01)

The information in this document is subject to change without notice. The statements, configurations, technical data, and rec-

ommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty.

Users must take full responsibility for their applications of any products specified in this document. The information in this

document is proprietary to Nortel Networks.

Trademarks

*Nortel, Nortel Networks, the Nortel logo, and the Globemark are trademarks of Nortel Networks.

All other products or services may be trademarks, registered trademarks, service marks, or registered service marks of their

respective owners.

The asterisk after a name denotes a trademarked item.

International Regulatory Statements of Conformity for the WSSs

This is to certify that the Nortel WLAN Security Switch 2300 series switches are evaluated to the international regulatory stan-

dards for electromagnetic compliance (EMC) and safety and was found to have met the requirements for the following interna-

tional standards:

• EMC - Electromagnetic Emissions – CISPR 22, Class A

• EMC - Electromagnetic Immunity – CISPR 24

• Electrical Safety – IEC 60950, with CB member national deviations

• Further, the equipment has been certified as compliant with the national standards as detailed below.

National Electromagnetic Compliance (EMC) Statements of Compliance

FCC statement (USA only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the

instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case users will be required to take whatever measures

may be necessary to correct the interference at their own expense.

ICES statement (Canada only)

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (WLAN Security Switch 2300 series switches) does not exceed the Class A limits for

radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des

Communications

Cet appareil numérique (WLAN Sécurité Changement 2300 changements de la série) respecte les limites de

bruits radioélectriques visant les appareils numériques de classe A prescrites dans le Règlement sur le brouillage

radioélectrique du ministère des Communications du Canada.

CE marking statement (Europe only)

EN 55022 statements

This is to certify that the Nortel WLAN Security Switch 2300 Series switches are shielded against the

generation of radio interference in accordance with the application of Council Directive 89/336/EEC.

Conformity is declared by the application of EN 55022 Class A (CISPR 22).

 Warning: This is a Class A product. In a domestic environment, this product may cause radio interference,

in which case, the user may be required to take appropriate measures.

 Achtung: Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb

dieses Gerätes Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende

Gegenmaßnahmen verantwortlich ist.

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

 Attention: Ceci est un produit de Classe A. Dans un environnement domestique, ce produit risque de créer

des interférences radioélectriques, il appartiendra alors à l’utilisateur de prendre les mesures spécifiques

appropriées.

EN 55024 statement

This is to certify that the Nortel WLAN Security Switch 2300 Series switches are shielded against the suscepti-

bility to radio interference in accordance with the application of Council Directive 89/336/EEC. Conformity is

declared by the application of EN 55024 (CISPR 24).

European Union and European Free Trade Association (EFTA) notice

All products labeled with the CE marking comply with the Electromagnetic Compliance (EMC) Directive

(89/336/EEC) and the Low Voltage Directive (73/336/EEC) issued by the Commission of the European

Community.

Compliance with these directives implies comformity to the following European Norms (ENs). The

equivalent international standards are listed in parenthesis.

• EN 55022 (CISPR 22)–Electromagnetic Interference

• EN 55024 (IEC 61000-4-2, -3, -4, -5, -6, -8, -11)–Electromagnetic Immunity

• EN 61000-3-2 (IEC 610000-3-2)–Power Line Harmonics

• EN 61000-3-3 (IEC 610000-3-3)–Power Line Flicker

VCCI statement (Japan/Nippon only)

This is a Class A product based on the standard of the Voluntary Control Council for Interference (VCCI) for

information technology equipment. If this equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective actions.

BSMI statement for Nortel WLAN Security Switch 2300 Series switches

(Taiwan only)

This is a Class A product based on the standard of the Bureau of Standards, Metrology and Inspection (BSMI) CNS

13438, Class A.

MIC notice (Republic of Korea only)

This device has been approved for use in Business applications only per the Class A requirements of the Republic of

Korea Ministry of Information and Communications (MIC). This device may not be sold for use in a non-business

application.

Observe the Regulatory Marking label on the back or bottom of each switch for specific certification information

pertaining to this model. Each model in the WLAN Security Switch 2300 Series is approved for shipment to/usage in

Korea and is labeled as such, with all appropriate text and the appropriate MIC reference number.

NN47250-300 (320655-E Version 02.01)

National Safety Statements of Compliance

EN 60950 statement

This is to certify that the Nortel WLAN Security Switch 2300 Series switches are in compliance with the

requirements of EN 60950 in accordance with the Low Voltage Directive. Additional national differences for all

European Union countries have been evaluated for compliance.

NOM statement (Mexico only)

The following information is provided on the devices described in this document in compliance with the safety

requirements of the Norma Oficial Méxicana (NOM):

Información NOM (unicamente para México)

La información siguiente se proporciona en el dispositivo o en los dispositivos descritos en este documento, en

cumplimiento con los requisitos de la Norma Oficial Méxicana (NOM):

Exporter: Nortel Networks

4655 Great America Parkway

Santa Clara CA 95054 USA

Importer: Nortel Networks de México, S.A. de C.V.

Avenida Insurgentes Sur #1605

Piso 30, Oficina

Col. San Jose Insurgentes

Deleg-Benito Juarez

México D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Input Model 2350 (with external power supply)

48V dc, 830mA, 40W

External Power Supply AC Input

100-240V ac, 50-60Hz, 1.0A

Input Model 2360 (single power supply)

100-240V ac, 50-60Hz, 2.0A

Model 2361 (with redundant supply)

100-240V ac, 50-60Hz, 2.0A

Input Model 2380 (single power supply)

100-240V ac, 50-60Hz, 8.0/3.5A

Model 2380 (with redundant supply)

100-240V ac, 50-60Hz, 8.0/3.5A

Input Model 2382 (with redundant supply)

100-240V ac, 50-60Hz, 1.0/0.5A

Exportador: Nortel Networks

4655 Great America Parkway

Santa Clara, CA 95054 USA

Importador:Nortel Networks de México, S.A. de C.V

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Denan Statement (Japan/Nippon only)

Importador: Nortel Networks de México, S.A. de C.V.

Avenida Insurgentes Sur #1605

Piso 30, Oficina

Col. San Jose Insurgentes

Deleg-Benito Juarez

México D.F. 03900

Tel: 52 5 480 2100

Fax: 52 5 480 2199

Entrada Modele 2350 (con suministro de corriente externo)

48V CC, 830mA, 40W

AC el suministro de Power externo

100-240V CA, 50-60Hz, 1,0A

Entrada Modele 2360 (solo suministro de corriente)

100-240V CA, 50-60Hz, 2,0A

Modele 2361 (con suministro redundante)

100-240V CA, 50-60Hz, 2,0A

Entrada Modele 2380 (solo suministro de corriente)

100-240V CA, 50-60Hz, 8,0/3,5A

Modele 2380 (con suministro redundante)

100-240V CA, 50-60Hz, 8,0/3,5A

Entrada Modele 2382 (con suministro redundante)

100-240V CA, 50-60Hz, 1,0/0,5A

NN47250-300 (320655-E Version 02.01)

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Contents

This document contains the following information:

•

Introduction (page 9)

— Audience (page 9)

— How to get help (page 9)

— Precautions (page 10)

• Preventing electrostatic damage in new cable installations (page 11)

— Planning a WLAN installation (page 13)

— Gathering required information (page 14)

— Preventing electrostatic discharge damage (page 10)

• Quick Start — Physical Installation (page 15)

— Installing the Nortel WLAN Security Switch (page 15)

— Installing a new power supply (page 17)

— Powering on the Nortel WLAN Security Switch (page 17)

— Powering on a 2382 (page 18)

— Connecting to the network (page 19)

• Quick Start — Basic Configuration (page 23)

— WSS startup algorithm (page 23)

— WSS sample network configuration (page 24)

— Configuring the Nortel WLAN Security Switch (page 24)

— Creating a scope on the DHCP server (page 25)

— Accessing the WSS CLI quickstart wizard (page 26)

— Installing and using WMS (page 28)

— Configuring WSS using WMS (page 31)

— Test the solution (page 35)

— Where to go next (page 35)

NN47250-300 (320655-E Version 02.01)

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Introduction

This Quickstart Guide provides basic instructions on how to install the hardware and perform basic configuration of a

Nortel WLAN Security Switch (WSS).

Audience

The Quickstart Guide is intended for experienced installers.

How to get help

This section explains how to get help for Nortel products and services.

Finding the latest updates on the Nortel web site

The content of this documentation was current at the time the product was released. To check for updates or receive

technical support for Nortel products, check the Nortel Technical Support web site:

http://www.nortel.com/support

This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel

products. From this site, you can:

• download software, documentation, and product bulletins

• search the Technical Support Web site and the Nortel Knowledge Base for answers to technical issues

• sign up for automatic notification of new software and documentation for Nortel equipment

• open and manage technical support cases

Getting help over the phone from a Nortel Solutions Center

If you do not find the information you require on the Nortel Technical Support web site, and you have a Nortel

support contract, you can also get help over the phone from a Nortel Solutions Center.

In North America, call 1-800-4NORTEL (1-800-466-7835).

Outside North America, go to the following web site to obtain the phone number for your region:

http://www.nortel.com/callus

Getting help from a specialist by using an Express Routing Code

To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route

your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to:

http://www.nortel.com/erc

Getting help through a Nortel distributor or reseller

If you purchased a service contract for your Nortel product from a distributor or authorized reseller, contact the

technical support staff for that distributor or reseller.

NN47250-300 (320655-E Version 02.01)

Precautions

Protecting cables and connectors

• Support cables in order to prevent any stress on the connectors. If you have a high cable density configuration,

you need to install additional cable management equipment.

• Do not exceed the bend radius recommended for the type of cable installed.

• Fiber optic cables and connectors require special care.

• Protect connectors with rubber safety plugs when cables are not inserted.

• When installing or replacing cables, follow appropriate fiber-cleaning procedures.

• Do not exceed the bend radius recommended for fiber optic cable. The acceptable bend radius for fiber optic

cable is ten times its diameter, or between 2.5 and 5 cm (1 to 2 in.). Anything less than the recommendation can

cause a loss of integrity of data transmission. Loss of integrity because of incorrect bend radius is difficult to

diagnose.

Preventing electrostatic discharge damage

Electrostatic discharge (ESD) is a discharge of stored static electricity that can damage equipment and impair

electrical circuitry. These electrostatic voltages can result from friction, including, but not exclusive to, pulling

cabling through conduits, walking across carpeted areas, and building up of static charge in clothing. ESD damage

occurs when electronic components are improperly handled and can result in complete or intermittent failures.

While networking equipment is commonly designed and tested to withstand common mode ESD events, voltage

sometimes can be discharged to some connector pins but not others, or to some pins before others, which has the

potential to damage the networking equipment.

To protect Nortel equipment against ESD damage, take the following preventive measures before connecting any data

cables to the device:

• Always use anti-static wrist straps. Make sure the strap is adjusted to provide good skin contact.

• Ensure that work surfaces and equipment racks are properly grounded for protection against electrostatic

discharge. The common point must be connected to the building ground wire. In a properly wired building, the

nearest reliable ground is typically at the electrical outlet.

• Avoid contact between equipment and clothing. The wrist or ankle strap only protects the equipment from ESD

voltages on the body; ESD voltages on clothing can still cause damage.

• Avoid touching any connector pins.

• Do not remove the wrist or ankle strap until the installation is complete.

WARNING

Installation must be performed by qualified service personnel only. Read and

follow all warning notices and instructions marked on the product or included

in the documentation. Before installing the product, read Translated caution

statements, warning conventions and warning messages (page 36).

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Preventing electrostatic damage in new cable installations

With new cable installations, Nortel recommends to use ESD discharge cable to reduce the potential for damage from

static that can build up in cables. An example of such a cable is illustrated below.

Figure 1: ESD Cable example

Step - Action

1 Connect the ground lug on the ESD discharge cable to a safe and suitable

earth ground.

2 Briefly connect all RJ-45 cable connectors to the female RJ-45 connector of

the ESD discharge cable, and then connect each RJ-45 cable connector to

the switch.

3 Leave cables connected to the networking equipment. Once cables are

connected to networking equipment, the cables do not build up charge.

NN47250-300 (320655-E Version 02.01)

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Before you begin

Before installing and configuring the WSS, the following basic planning steps must be completed.

Planning a WLAN installation

The WLAN Management Software (WMS) can only be installed on a single computer. You must decide which

computer will be used to manage the WSS, and ensure that computer is accessible during the installation and

configuration process.

The WMS installation CD is distributed with a license certificate to specify the serial number and Nortel Support

email address. An email request must be sent to Nortel Support to receive the WMS license activation key as follows:

• WMS serial number — This serial number is listed on the license certificate included with the WMS CD.

• computer name — The computer name where WMS will be installed.

• company name — The name of your company.

A license activation key is required to use WMS, and must be available before you begin to configure the WSS.

When planning to install a wireless Access Point (AP), be sure to record the model and serial number printed on the

back of the AP. This information is required when configuring WSS ports and Access Points (AP) using WMS. If the

AP is already physically installed in a difficult to access location, the model and serial numbers are also printed on

the box used to deliver the AP.

Some additional basic network information is also required before WMS configuration takes place, as described in

“Gathering required information” on page 14.

NN47250-300 (320655-E Version 02.01)

Gathering required information

Before installing or configuring the WSS, print a copy of this page and ensure that all value fields in Table 1 have

been filled in correctly. Keep this information close by during the configuration process.

Table 1: Required information

Information Description Values

Computer name Each WMS license is limited to a single computer.

WMS serial number The WMS serial number and instructions for

obtaining a license key are included on a sheet of

paper inside the WSS box.

WMS license key The WMS license activation key must be received

from Nortel.

IP subnet address The IP subnet address of the WLAN 2300 System.

DNS server IP address The IP address of the DNS server.

Domain name The domain name where the WLAN 2300 System is

located.

AP model number The AP model that is being used in your WLAN

2300 System.

AP serial number Each AP has a unique serial number on the bottom of

the AP. This serial number is required when

configuring the WSS.

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Quick Start — Physical Installation

This section describes how to physically install a WSS. For more information about physical installation, see Nortel

WLAN—Security Switch 2300 Series Installation and Basic Configuration Guide.

Installing the Nortel WLAN Security Switch

Estimated timing: 10 minutes

A WSS can be installed on either a tabletop surface or in an equipment rack. Table 2 outlines which installation

methods are available for each WSS model.

When choosing a location for the WSS, ensure that:

• The power outlet is within 1.82 m (6 ft) of the device.

• There is proper heat dissipation from and adequate ventilation around the

switch.

Tabletop Installation

Step Action

1 Ensure that the table surface supports at least 3 kg (6.6 lb).

2 Carefully turn the WSS upside down on a clean work surface with no debris.

3 Wipe the four placement locations for the rubber feet to clear away any oil or dust.

Each location area is marked with an ‘X’.

4 Attach the four rubber adhesive feet over the ‘X’s.

5 Turn the WSS right-side up, and place the switch in position on the table.

End

Equipment Rack Installation

Step Action

1 Remove the four bracket screws from each side of the WSS.

2 Align a bracket over the screw holes:

• For a front-mount equipment rack, align the bracket so that the bracket flange is

flush with the WSS front panel and away from the switch.

• For a center-mount equipment rack, align the bracket so that the bracket flange

is located near the center screw holes, as shown in Figure 2.

Table 2: Installation methods

WSS model Tabletop Front-mount rack Center-mount rack

2350 X

2360/2361 X X

2380 X X X

2382 X X X

NN47250-300 (320655-E Version 02.01)

Figure 2: 2380 Installation—Center-Mount Equipment Rack

3 Reinsert the screws to secure the brackets to the WSS.

4 Repeat for the other bracket.

5 Lift the WSS into position in the equipment rack.

6 Insert the bottom rack-mount screws into the bracket flanges to secure the WSS to the

equipment rack, then insert the top screws.

End

CAUTION

Nortel recommends that you ask someone to assist you with the

remaining steps. If you accidentally drop the WSS, you can be injured

and the switch can be damaged.

840-9502-0057

First, attach brackets to chassis.

Then, install chassis into rack.

Console

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Installing a new power supply

Estimated timing: 5 minutes

Some WSS models support secondary power supplies. To install a secondary power supply, complete the following

steps:

Step Action

1 Loosen the thumbscrew in an unused slot with a #2 Phillips-head screwdriver, and

remove the cover plate.

2 Remove the new power supply from its packaging and lift the supply by grasping the

front handle with one hand and supporting the supply from the bottom with the other

hand.

3 Insert the power supply into the slot as shown in Figure 3, pushing gently but firmly until

the supply is fully seated and flush with the switch’s front panel.

Figure 3: Inserting a Power Supply in a 2380 Switch

4 Tighten the thumbscrew using a #2 Phillips-head screwdriver.

End

Powering on the Nortel WLAN Security Switch

Estimated timing: 5 minutes

Powering on a 2350

Step Action

1 Plug the external power supply input AC cord into an AC power source.

2 Attach the external power supply DC output cable to the Power port on the 2350.

The 2350 begins booting as soon as you plug in the power cord.

3 Ensure that the external power supply LED and the 2350 power LED turn green to

verify that the external power supply is operating normally.

End

840-9502-0060

NN47250-300 (320655-E Version 02.01)

Powering on a 2360/2361

Step ActionStep

1 Attach the approved AC power cord to each Power port on the 2360 or 2361 (2 power

ports).

2 Plug the power cord (s) into the AC power source (s).

The 2360 or 2361 begins booting as soon as you plug in the power cord(s).

3 On the 2360 ensure that the power supply LED turns green to verify that the power

supply is operating normally. On the 2361 observe each power supply. LED to verify

that both power supplies are operating normally.

Powering on a 2380

Step Action

1 Ensure that any removable power supply is fully seated in the 2380.

2 For each power supply that you are using on the 2380, attach a power cord.

3 Plug each power cord into an AC power source.

The 2380 begins booting as soon as you plug in the power cord(s).

4 On each 2380 power supply ensure that the power LED turns green to verify that the

power supply is operating normally. For the 2380 switch, wait a few seconds to verify

that the Mgmt LED is functioning (repeatedly flashing bright green, then fading).

End

Powering on a 2382

Step Action

1 Ensure that any removable power supply is fully seated in the 2382.

2 For each power supply that you are using on the 2382, attach a power cord.

3 Plug each power cord into an AC power source.

The 2382 begins booting as soon as you plug in the power cord(s).

4 On each 2382 power supply ensure that the power LED turns green to verify that the

power supply is operating normally. For the 2382 switch, wait a few seconds to verify

that the Mgmt LED is functioning (repeatedly flashing bright green, then fading).

End

Note: The WSS 2382 runs only on Version 6.0 software and later releases.

Software Versions prior to 6.0 will not run on this hardware.

Nortel WLAN - Security Switch 2300 Series Quick Start Guide

Connecting to a Serial Management Console

Estimated timing: 5 minutes

Step Action

1 Insert the serial cable into the PC port.

2 Insert the other end of the cable into the serial console port on the WSS.

3 Start a standard VT100 terminal emulation application on the PC, and configure the

modem settings listed in Table 3.

4 Open a terminal connection on a serial port.

If the WSS is already powered on, then the terminal connection will request a

password. Leave the password field blank, because the default password is not set.

5 Press Enter until the command prompt appears.

End

Connecting to the network

Estimated timing: 5 minutes

Connecting Access Points

Use the following procedure to connect a AP to the WSS or to another PoE-capable 10/100 ethernet device. For

information about the physical installation of APs, see Nortel WLAN—Access Point 2330A/2330B Quick Installation

Guide or Nortel WLAN—Series 2332 Access Point Quick Installation Guide.

Step Action

1 Connect an ethernet cable to the AP.

2 Connect the other end of the ethernet cable to the WSS port, or to the ethernet device.

• If connecting the AP to the WSS, the AP will not receive power until PoE is

enabled for that port.

Table 3: Communication protocol settings

Setting Value

Baud rate 9600 bps

Data bits 8 bits

Stop bits 1 stop

Parity No parity

Flow Control off or disabled

NN47250-300 (320655-E Version 02.01)

• If connecting the AP to an ethernet device other than the WSS, observe the

appearance of the AP LED for the port.

Table 4 describes the AP LED appearance and associated meaning.

End

Connecting other ethernet network devices

Use the following procedure to connect a WSS to other 10/100 Ethernet devices, or a gigabit Ethernet device.

Step Action

1 Insert a Cat-5 cable with a standard RJ-45 connector.

• Use a straight-through cable to connect to a router, Access Point (AP), or an end

station such as a PC, printer, or server.

• Use a crossover cable to connect to another switch.

2 If the cable is attached to a wired end station that uses AAA through the WSS to

access the network, set the port type for a wired authentication port to activate the link.

Table 4: AP LED indicator status

AP LED Appearance Meaning

Solid green For an AP active link, with PoE enabled, the following are

true:

• AP has booted. AP has received a valid configuration

from the WSS.

• Management link with an AP is operational.

• For an AP’s secondary link, the link is present.

Alternating green and amber AP is booting with an image received from the WSS.

Solid amber PoE is enabled, but the AP is not connected to the network.

Blinking amber AP is unresponsive or there is a PoE problem.

Unlit PoE is disabled.

Note: The 10/100 Ethernet ports on 2360/2361 switches provide automatic

MDI/MDX.

La pagina sta caricando ...

Nortel Networks 2382 Manuale utente

Marca: Nortel Networks

Modello: 2382

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Nortel Networks 2382 User manual
français: Nortel Networks 2382 Manuel utilisateur

Nortel Networks 2382 Manuale utente

Questo manuale è adatto anche per

Nortel Networks 2382 Manuale utente

in altre lingue

Documenti correlati

Altri documenti