1480K03H
OPERATION MANUAL
FOR DISPLAYS OF SERIES
DT-203NP, DT-105NP AND DT-110NP
Index
1 INTRODUCTION ........................................................................................................................... 1-1
2 GENERAL CHARACTERISTICS. ................................................................................................. 2-1
2.1 Electrical characteristics of the displays ............................................................................... 2-1
2.1.1 Electrical characteristics of the DT-203 displays. ............................................................. 2-1
2.1.2 Electrical characteristics of the DT-105 displays. ............................................................. 2-1
2.1.3 Electrical characteristics of the DT-110 displays. ............................................................. 2-1
2.2 Display Weight and power consumption. ............................................................................. 2-2
2.3 Dimensions of the displays ................................................................................................... 2-3
3 INSTALLATION. ............................................................................................................................ 3-1
3.1 Power supply. ....................................................................................................................... 3-1
3.2 Connecting to the Profibus line............................................................................................. 3-2
3.3 Characteristics of temperature & humidity probe. (Option) .................................................. 3-2
3.4 Wiring of temperature & humidity probe (Option) ................................................................. 3-2
3.5 Reset button ......................................................................................................................... 3-2
4 OPERATION ................................................................................................................................. 4-1
4.1 Initial Start Up. ...................................................................................................................... 4-1
4.2 Leds Profibus module. .......................................................................................................... 4-1
4.3 Set parameters. .................................................................................................................... 4-2
4.3.1 Enter to modify parameters. ............................................................................................. 4-2
4.3.2 Exit modify parameters. .................................................................................................... 4-2
4.3.3 Function of each parameter. ............................................................................................. 4-2
4.4 Memory message programming ........................................................................................... 4-3
4.5 Profibus protocol. .................................................................................................................. 4-4
4.5.1 Block Structure ................................................................................................................. 4-4
4.5.2 Valid characters. ............................................................................................................... 4-5
4.5.3 DW1 Register ................................................................................................................... 4-5
4.5.4 Message and variable management ................................................................................ 4-7
4.5.5 Variable control register .................................................................................................... 4-7
4.5.6 Register DW1-A = 1. Functions of bytes B, C and D of register DW1. ............................ 4-7
4.5.7 Message text. ................................................................................................................... 4-8
4.5.8 Register DW1-A = 2. Control commands. ........................................................................ 4-8
4.6 GSD module installation. ...................................................................................................... 4-9
CHAPTER 1
INTRODUCTION
1-1
DT-203NP, DT-105NP and DT-110NP display series
1 INTRODUCTION
The alphanumerical displays for series DT-203NE, DT-105NE and DT-110NE, are industrial displays
for control by Profibus network.
The selection of the parameters and the communication protocol is done using two buttons
with a system of easily programmable menu.
One of its main characteristics is the height of the characters:
DT-203NP of 30mm, readable from up to 15m.
DT-105NP of 50mm, readable from up to 25m.
DT-110NP of 100mm, readable from up to 50m.
As with other display series, the DT-NP series is also available in one or two-sided versions,
which provides multiple solutions and installation possibilities.
It is surface mounted, with fixtures to a wall or partition wall, or suspended by the side
anchoring.
The application field of these displays is very wide in all types of industrial applications utilising
the advantages of the Profibus network. They can be used to display Scada program values, counter
values from a PLC, warning messages, advertisements.
CHAPTER 2 GENERAL CHARACTERISTICSINTRODUCTION 2-1
DT-203NP, DT-105NP and DT-110NP display series
2 GENERAL CHARACTERISTICS.
2.1 Electrical characteristics of the displays
2.1.1 Electrical characteristics of the DT-203 displays.
Supply Voltage ........................................... 88 to 264 VAC 47 to 63Hz. Option 24VDC.
Consumption ............................................. Read chapter 2.2.
Display ....................................................... 7x5 Dot matrix of 30mm high.
..................................................................... Red Led colour. Visibility 15 meters.
Parameter memory .................................... Eeprom.
Watch calendar .......................................... Second / Minute / Hour / Day / Month / Year.
Communication ......................................... Profibus DP slave
..................................................................... Auto detection baud rate. Max.12MHz.
Communication protocol .......................... Profibus and TDL. Selection by parameters.
Environmental Conditions ........................ Operation Temperature: -20 to 60ºC.
..................................................................... Storage temperature: -30ºC to 70ºC.
..................................................................... Humidity: 5-95% without condensation.
..................................................................... Maximum environmental illumination: 1000 lux.
..................................................................... Sealing: IP41, IP54 and IP65.
2.1.2 Electrical characteristics of the DT-105 displays.
Supply Voltage ........................................... 88 to 264 VAC 47 to 63Hz. Option 24VDC.
Consumption ............................................. Read chapter 2.2.
Display ....................................................... 7x5 Dot matrix of 50mm high.
..................................................................... Red Led colour. Visibility 25 meters.
Parameter memory .................................... Eeprom.
Watch calendar .......................................... Second / Minute / Hour / Day / Month / Year.
Communication ......................................... Profibus DP slave
..................................................................... Auto detection baud rate. Max.12MHz.
Communication protocol .......................... Profibus and TDL. Selection by parameters.
Environmental Conditions ........................ Operation Temperature: -20 to 60ºC.
..................................................................... Storage temperature: -30ºC to 70ºC.
..................................................................... Humidity: 5-95% without condensation.
..................................................................... Maximum environmental illumination: 1000 lux.
..................................................................... Sealing: IP41, IP54 and IP65.
2.1.3 Electrical characteristics of the DT-110 displays.
Supply Voltage ........................................... 88 to 264 VAC 47 to 63Hz. Option 24VDC.
Consumption ............................................. Read chapter 2.2.
Display ....................................................... 7x5 Dot matrix of 100mm high.
..................................................................... Red Led colour. Visibility 50 meters.
Parameter memory .................................... Eeprom.
Watch calendar .......................................... Second / Minute / Hour / Day / Month / Year.
Communication ......................................... Profibus DP slave
..................................................................... Auto detection baud rate. Max.12MHz.
Communication protocol .......................... Profibus and TDL. Selection by parameters.
Environmental Conditions ........................ Operation Temperature: -20 to 60ºC.
..................................................................... Storage temperature: -30ºC to 70ºC.
..................................................................... Humidity 5-95% without condensation.
..................................................................... Maximum environmental illumination: 1000 lux.
..................................................................... Sealing: IP41, IP54 and IP65.
2-2 GENERAL CHARACTERISTICS CHAPTER 2
DT-203NP, DT-105NP and DT-110NP display series
2.2 Display Weight and power consumption. Exterior option use column h(VA)
Reference
Weight
(kg)
Power
(VA)
Power
h (VA)
Reference
Weight
(kg)
Power
(VA)
Power
h (VA)
DT-105/1S-6
4
12
25
DT-110/1S-6
6,5
12
25
DT-105/1D-6
4
16
46
DT-110/1D-6
7,5
16
46
DT-105/1S-13
5,5
16
46
DT-110/1S-13
10,5
16
46
DT-105/1D-13
6
28
90
DT-110/1D-13
13
28
90
DT-105/1S-20
7
22
68
DT-110/1S-20
14,5
22
68
DT-105/1D-20
8
38
134
DT-110/1D-20
18
38
134
DT-105/1S-26
9
28
90
DT-110/1S-26
19
28
90
DT-105/1D-26
10
50
179
DT-110/1D-26
23,5
50
179
DT-105/1S-33
10,5
34
112
DT-110/2S-6
9
16
48
DT-105/1D-33
12
60
222
DT-110/2D-6
11,5
28
90
DT-105/1S-40
12
38
136
DT-110/2S-13
15
28
90
DT-105/1D-40
14
72
266
DT-110/2D-13
20
50
178
DT-105/2S-6
5
16
48
DT-110/2S-20
21
38
134
DT-105/2D-6
5,5
28
90
DT-110/2D-20
28
72
266
DT-105/2S-13
7
28
90
DT-110/2S-26
27
50
180
DT-105/2D-13
8
50
178
DT-110/2D-26
36,5
92
354
DT-105/2S-20
9
38
134
DT-110/3S-6
12
22
68
DT-105/2D-20
10,5
72
266
DT-110/3D-6
15,5
38
112
DT-105/2S-26
11
50
180
DT-110/3S-13
20
38
136
DT-105/2D-26
13,5
92
354
DT-110/3D-13
27
72
244
DT-105/2S-33
13,5
60
220
DT-110/3S-20
27,5
55
200
DT-105/2D-33
16
115
442
DT-110/3D-20
38,5
105
376
DT-105/2S-40
15,5
72
266
DT-110/3S-26
35,5
72
266
DT-105/2D-40
19
138
530
DT-110/3D-26
49,5
138
510
DT-105/3S-6
5,5
22
68
DT-110/4S-20
34
72
268
DT-105/3D-6
6,5
38
112
DT-110/4D-20
48,5
138
486
DT-105/3S-13
8,5
38
136
DT-110/5S-20
41
88
330
DT-105/3D-13
10
72
244
DT-110/5D-20
58
170
600
DT-105/3S-20
11
55
200
DT-110/6S-20
47,5
105
400
DT-105/3D-20
13,5
105
376
DT-110/6D-20
68,5
204
700
DT-105/3S-26
13,5
72
266
DT-110/7S-20
53,5
120
465
DT-105/3D-26
17
138
510
DT-110/7D-20
78,5
240
820
DT-105/3S-33
16
90
332
DT-110/8S-20
60
140
530
DT-105/3D-33
20,5
170
640
DT-110/8D-20
88,5
280
930
DT-105/3S-40
18,5
105
400
DT-203/2S-20
6
35
----
DT-105/3D-40
24
205
770
DT-203/2D-20
6,5
60
----
DT-105/4S-20
12,5
72
268
DT-203/2S-40
9
60
----
DT-105/4D-20
16
138
486
DT-203/2D-40
10,5
120
----
DT-105/5S-20
14,5
88
330
DT-203/4S-20
7,5
60
----
DT-105/5D-20
18,5
170
600
DT-203/4D-20
9
120
----
DT-105/6S-20
16,5
105
400
DT-203/4S-40
12
120
----
DT-105/6D-20
21,5
204
700
DT-203/4D-40
15
240
----
DT-105/7S-20
18
120
465
DT-203/6S-20
9
90
----
DT-105/7D-20
24
240
820
DT-203/6D-20
11,5
180
----
DT-105/8S-20
20
140
530
DT-203/8S-20
11
120
----
DT-105/8D-20
27
280
930
DT-203/8D-20
14
240
----
CHAPTER 2 GENERAL CHARACTERISTICSINTRODUCTION 2-3
DT-203NP, DT-105NP and DT-110NP display series
2.3 Dimensions of the displays
A
B
C
D
E
F
G
P1
P2
P3
DT-105/1S(D)-6
375
118
109
X
X
X
358
O
X
X
DT-105/1S(D)-13
680
118
109
X
X
X
663
O
X
X
DT-105/1S(D)-20
985
118
109
X
X
X
968
O
X
X
DT-105/1S(D)-26
1290
118
109
X
X
X
1273
O
X
X
DT-105/1S(D)-33
1595
118
109
X
X
X
1578
O
X
X
DT-105/1S(D)-40
1900
118
109
X
X
X
1883
O
X
X
DT-105/2S(D)-6
375
230
112
X
X
X
358
O
X
X
DT-105/2S(D)-13
680
230
112
X
X
X
663
O
X
X
DT-105/2S(D)-20
985
230
112
X
X
X
968
O
X
X
DT-105/2S(D)-26
1290
230
112
X
X
X
1273
O
X
X
DT-105/2S(D)-33
1595
230
112
X
X
X
1578
O
X
X
DT-105/2S(D)-40
1900
230
112
X
X
X
1883
O
X
X
DT-105/3S(D)-6
375
338
X
72
186
X
358
X
O
O
DT-105/3S(D)-13
680
338
X
72
186
X
663
X
O
O
DT-105/3S(D)-20
985
338
X
72
186
X
968
X
O
O
DT-105/3S(D)-26
1290
338
X
72
186
X
1273
X
O
O
DT-105/3S(D)-33
1595
338
X
72
186
X
1578
X
O
O
DT-105/3S(D)-40
1900
338
X
72
186
X
1883
X
O
O
DT-105/4S(D)-20
985
436
X
72
292
X
968
X
O
O
DT-105/5S(D)-20
985
542
X
92
358
X
968
X
O
O
DT-105/6S(D)-20
985
648
X
112
424
X
968
X
O
O
DT-105/7S(D)-20
985
754
377
72
610
305
968
O
O
O
DT-105/8S(D)-20
985
860
430
72
716
358
968
O
O
O
DT-110/1S(D)-6
666
177
82,5
X
X
X
649
O
X
X
DT-110/1S(D)-13
1276
177
82,5
X
X
X
1259
O
X
X
DT-110/1S(D)-20
1886
177
82,5
X
X
X
1869
O
X
X
DT-110/1S(D)-26
2496
177
82,5
X
X
X
2479
O
X
X
DT-110/2S(D)-6
666
378
X
80
218
X
649
X
O
O
DT-110/2S(D)-13
1276
378
X
80
218
X
1259
X
O
O
DT-110/2S(D)-20
1886
378
X
80
218
X
1869
X
O
O
DT-110/2S(D)-26
2496
378
X
80
218
X
2479
X
O
O
DT-110/3S(D)-6
666
591
X
80
430
X
649
X
O
O
DT-110/3S(D)-13
1276
591
X
80
430
X
1259
X
O
O
DT-110/3S(D)-20
1886
591
X
80
430
X
1869
X
O
O
DT-110/3S(D)-26
2496
591
X
80
430
X
2479
X
O
O
DT-110/4S(D)-20
1886
805
403
80
646
322,5
1869
O
O
O
DT-110/5S(D)-20
1886
1018
509
80
858
429
1869
O
O
O
DT-110/6S(D)-20
1886
1232
616
80
1072
536
1869
O
O
O
DT-110/7S(D)-20
1886
1445
723
80
1286
643
1869
O
O
O
DT-110/8S(D)-20
1886
1654
830
80
1500
750
1869
O
O
O
DT-203/2S(D)-20
615
177
85
X
X
X
598
O
X
X
DT-203/2S(D)-40
1170
177
85
X
X
X
1153
O
X
X
DT-203/4S(D)-20
615
317
X
72
173
X
598
X
O
O
DT-203/4S(D)-40
1170
317
X
72
173
X
1153
X
O
O
DT-203/6S(D)-20
615
464
X
91
282
X
598
X
O
O
DT-203/8S(D)-20
615
611
X
112
387
X
598
X
O
O
See the draw on the next page
2-4 GENERAL CHARACTERISTICS CHAPTER 2
DT-203NP, DT-105NP and DT-110NP display series
Measures in millimetres. X = Not valid for these model.
P1, P2 and P3: Anchorage point. Used = O. Not used = X. Anchorage holes position on the
wall. See valid point (P1, P2 o P3) on the table in the previous page.
120
A
F
F
D D
CC
E
P1
P3
P2
P1
P3
P2
G
40
Ø5
B
F
F
CHAPTER 3
INSTALLATION
3-1
DT-203NP, DT-105NP and DT-110NP display series
3 INSTALLATION.
The installation of the DT-203, DT-105 y DT-110, is not particularly delicate but some
important considerations must be taken into account.
It must not be anchored to places subject to vibrations, nor should it be installed in
places which generally surpass the limits specified in the display characteristics, both in terms of
temperature and humidity.
The degree of protection of displays DT-203, DT-105 and DT-110 is IP41, meaning that
they are protected against penetration by solid foreign objects of a diameter of about 1mm and
against the vertical fall of water droplets. The DT-203f, DT-105f and DT-110f are IP54, which
mean that are more protected. DT-203e, DT-105e and DT-110e are IP65.
Displays DT-203, DT-105 and DT-110, should not be installed in places with illumination
level higher than 1000 lux. Neither should the display be placed in direct sunlight as visibility
would be lost. Displays DT-105h and DT-110h can be read in sunlight.
In the electrical installation, proximity to lines of high intensity circulation and high
voltage lines must be avoided, as well as proximity to High Frequency generators and U/F
converters for motors.
3.1 Power supply.
The power supply must be 88 to 264 VAC 47 to 63Hz or 24VDC with 24V option.
The power supply conductor section will be in line with consumption and the ground
conductor will be a minimum section of 1.5mm².
The power supply connector for 220VAC has 3 contacts and is situated in the lower part of the
unit. Connect the power wires following the schema below
The power supply connector for 24VDC has 4 contacts and is situated in the lower part of the
unit. Connect the power wires following the schema below
1
3
2
1- 24V
2- 0V
3- GND
4
1
321- 230V
2- 230V
3- GND
3-2 INSTALLATION CHAPTER 3
DT-203NP, DT-105NP and DT-110NP display series
3.2 Connecting to the Profibus line.
Profibus line connection is carried out using an DB-9 connector located in the lower part
of the unit.
The terminal resistances will be enabled on the ends of the network to adjust network
impedance The Profibus connectors include a switch to enable resistances.
Power lines that may generate electrical interference will be avoided where possible on the
network layout.
3.3 Characteristics of temperature & humidity probe. (Option)
Relative humidity
Resolution .......................................... Typical 1%.
Accuracy ............................................ ±3,5% between 30% and 70%.
Warm-up time .................................... 4s.
Temperature
Resolution .......................................... Typical 0,1°C.
Accuracy ........................................... ±0,5°C at 25°C.
Warm-up time .................................... 20s.
Range .................................................. From –20°C to +80°C.
3.4 Wiring of temperature & humidity probe (Option)
The temperature & humidity probe is delivered with 5m cable and a Sub-D9 connector
ready to use.
The wiring of connector probe is shown in the diagram (cable connector).
3.5 Reset button
If the computer has been out of power for many days, the battery may be discharged. If,
when the power is restored, the battery is not fully charged, it may be necessary to force the
device to be reset. The reset button is next to the power connector. The display must be
connected to the power supply for the reset to be operative.
1
2
4
5
6
3
7
DB9
Free plug
0V (White)
+5V (Brown)
SCK (Green)
Data (Yellow)
9
8
CONECTOR
PROFIBUS
OP : Modo Operación ST : Estado
Pin 1 : NC Pin 6 : +5V Bus Output
Pin 2 : NC Pin 7 : NC
Pin 3 : Línea B (+) Pin 8 : Línea A (-)
Pin 4 : RTS Pin 9 : NC
Pin 5 : GND Bus Carcasa : Malla
15
69
OP ST
DB-9
CHAPTER 4
OPERATION
4-1
DT-203NP, DT-105NP and DT-110NP display series
4 OPERATION
4.1 Initial Start Up.
Before connecting the display to the network, we must ensure that all of the connections have
been carried out correctly and that the display is firmly in place.
Every time the display is connected to the power supply there is an initial reset, which check
all points of the display. After the initial reset the version code is displayed.
Following the initial reset, the display reads the message memory and initialises the messages
table. The word “INICI” is shown until the display is prepared to receive messages.
Where the Profibus module has been initialised correctly, the ST led will light up green. If the
network is configured correctly and the display is connected to the network, the OP led will light up
green. When the initialisation process is finished, the display is ready to receive data. While waiting
for the first message the display shows a programmed message on the memory.
Protocol TDL: Display all memory messages.
Protocol Profibus: Display message 0.
4.2 Leds Profibus module.
The Profibus module has two leds to indicate the operation and status.
Led OP
Operation
Led ST
Status
Off
Not onlien / No power
Off
No power or not initialised
Green
On line, data Exchange
Green
Initialised
Flashing Green
On line, clear
Flashing
Green
Initialised, diagnostic event present
Flashing red
Service error
Red
Exception error
4-2 OPERATION CHAPTER 4
DT-203NP, DT-105NP and DT-110NP display series
4.3 Set parameters.
Before using the display the user must set the parameters:
The parameters are:
1- Menu language
2- Display address
3- Protocol.
4- Number of register DW.
5- Display’s date.
6- Display’s time.
7- Level of leds luminosity.
8- Test Profibus.
9- Connectors position.
10- Exit menu.
To set the parameters, the display has a pair of pushbuttons located at the bottom of the case.
The menu is in four languages.
4.3.1 Enter to modify parameters.
In order to enter the sequence to modify the parameters, the Advance key “*” must be pressed
and held for three seconds. After this, the first parameters will be displayed, with the digit flashing.
There are then two options:
Modify the parameter value
By pressing the Advance key "*", entry is gained to modify the parameter value.
To go back to displaying the parameter number, press “*”again.
To increase the parameter value, press the “+” key. After parameter EXIT it returns to
parameter LANGUAGE.
Select another parameter
In order to select another parameter, the parameter number must be made to flash using the
“*” key and then the new parameter may be selected using the “+” key.
4.3.2 Exit modify parameters.
In order to exit the sequence for modifying parameters, parameter EXIT must be selected then
press "*".
4.3.3 Function of each parameter.
4.3.3.1 Parameter 1: LANGUAGE or LA.
The language menu. There are four languages available: Catalan, Spanish, French and
English.
4.3.3.2 Parameter 2: ADDRESS or AD.
The display address in the Profibus network.
Valid values from 04 to 99.
4.3.3.3 Parameter 3: PROTOCOL or PR
The protocols available are:
PROFIBUS To be used with Profibus network
TDL To program the messages with TDLWin and RS-232 port.
CHAPTER 4
OPERATION
4-3
DT-203NP, DT-105NP and DT-110NP display series
4.3.3.4 Parameter 4: N.REGS DW or DW:
Number of DW registers to be read from PLC.
If the register number is equal 0, the number of registers to be read is indicated in paragraph
4.6 If the register number is greater than 0 it must be equal to the number assigned in the GSD
setup.
4.3.3.5 Parameter 5: DATA or DA
Allows you to modify the display date
4.3.3.6 Parameter 6: TIME or TM
Allows you to modify the display time.
The time, with seconds equal to 0, is set at menu exit.
4.3.3.7 Parameter 7: BRIGHTNESS or BRI
Allows you to modify the display brightness. Level 1 is the minimum brightness while level 8 is
the maximum brightness.
4.3.3.8 Parameter 8: TEST PROFIBUS or TP
Communications status with the network can be seen
The value 0 does not display the status. The value 1 displays the network status when
communications are not possible.
Where the Profibus module has been correctly started but there are no com munications with
the network, the following is displayed: Profibus = 10 or Pro=10. Any value from Profibus = 0 or
Pro=0 to Profibus = 9 or Pro=9corresponds to the Profibus module start up process. Where the
value Profibus = 10 or Pro=10 is not displayed 5 seconds after starting the start-up process, the
equipment must be repaired.
4.3.3.9 Parameter POS. CONNECTORS or CON
Selects the power and Ethernet connectors’ position. Depending on the installation, it may be more
convenient for the connectors to come out at the top or at the bottom of the display. This parameter
reverses the text if the display is installed in reverse position.
4.3.3.10 Parameter 10: END
To exit modify parameter menu, push advance key (“*”).
4.4 Memory message programming
Two forms of communications are possible with the Profibus-DP protocol:
1- By sending all the text to be displayed in ASCII format
2- By sending the code of a message previously saved on the display.
To use the second method, messages must be saved on the display using a PC and the
TDLWin programme version 1.5 or above, which allows for messages to be edited, saved and
transferred.
This programme must also be used to modify the message appearing when equipment start
up is complete (message 0).
4-4 OPERATION CHAPTER 4
DT-203NP, DT-105NP and DT-110NP display series
To transfer messages to the display, use a cable as indicated in Section 2.7, configure the
display parameter PROTOCOL = TDL and the TDLWin programme: 9600 Bauds, parity even, 8 data
bits, 2 stop bits.
In the display model, adjust the one with the same number of lines as the equipment to be
programmed.
4.5 Profibus protocol.
4.5.1 Block Structure
The length of the transmission block varies depending on the number of lines on the display.
The double word (DW) is the basic block unit. The following table indicates the number of double
words (DW) that must be sent, depending on the number of lines. The fact that the display has two
sides does not affect the frame because the same message is displayed on both sides.
By means of parameter N.REGS DW the number of registers to be read from PLC may be
modified. If N.REGS DW is equal to 0 the number of register to be read follows the table below.
Numbers of lines
1
2
3
4
5
6
7
8
Number of registers
6
11
16
21
21
21
21
21
The way in which the message, the values of the variables or the text is sent is coded in the
DW1 register.
1 Line
DW1
DW2
DW3
DW4
DW5
DW6
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
V
W
X
Y
2 Line
DW7
DW8
DW9
DW10
DW11
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
V
W
X
Y
3 Line
DW12
DW13
DW14
DW15
DW16
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
V
W
X
Y
4 to 8 Line
DW17
DW18
DW19
DW20
DW21
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
V
W
X
Y
CHAPTER 4
OPERATION
4-5
DT-203NP, DT-105NP and DT-110NP display series
4.5.2 Valid characters.
Alphanumerical displays can display all the alphabet characters, numbers and some special
characters. The table in the next page shows all the valid characters. ASCII code in hexadecimal is
used.
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0
1
↑
↓
→
←
.
▲
▼
2
!
"
#
$
%
&
'
(
)
*
+
,
-
.
/
3
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
4
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
↑
←
6
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
7
p
q
r
s
t
u
v
w
x
y
z
£
¥
½
¯
⌂
8
Ç
ü
é
â
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
9
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
ø
£
Ø
€
ƒ
A
á
í
ó
ú
ñ
Ñ
ª
º
¿
¬
¡
«
»
B
↓
↑
→
←
→
←
─
─
C
=
D
E
α
β
F
±
≥
≤
º
4.5.3 DW1 Register
This is the most important register as it directs all the other registers in the frame. Each one of
the four bytes (A, B, C, D) forming it, has the following function:
DW1-A: Indicates the type of message
DW1-A = 0 To display the text of a message previously saved in the display memory. The
number is coded in bytes C and D.
DW1-A = 1 To indicate that the text of the message is sent within the rest of the frame.
Maximum 20 characters per line.
DW1-A = 2 The frame sent is a control command. This does not affect the text displayed.
4.5.3.1 Register DW1-A = 0. Function of bytes B, C and D of DW1 register.
If the register DW1-A is equal to 0, the text of a message previously saved in the display
memory is displayed using the TDLWin programme.
DW1-B: On displays with over 4 lines, an indication must be given as to whether the
information on the frame is for the 4 upper lines or the 4 lower.
DW1-B = 0 Data for the 4 upper lines and displays of 1 to 4 lines.
DW1-B = 1 Data for the 4 lower lines. Displays of 5 to 8 lines.
DW1-C: Heavy weight of the message number to be displayed. In hexadecimal
DW1-D: Light weight of the message number to be displayed. In hexadecimal
Example:
Enabling message 24 DW1-C = 0 DW1-D = 18
Enabling message 363 DW1-C = 1 DW1-D = 6B
4-6 OPERATION CHAPTER 4
DT-203NP, DT-105NP and DT-110NP display series
4.5.3.2 Register DW1-A = 0. Function of registers DW2, DW7, DW12 and DW17
Where the register DW1-A is equal to 0, the registers DW2, DW7, DW12 and DW17 indicate
how the variables are managed.
Remember that more or less registers are used depending on the number of lines on the
equipment.
For every line on the display, up to 16 variable characters can be managed. Each character is
assigned two control bits
CONTROL
REGISTER WITH THE VALUES
DW 2
DW 3
DW 4
DW 5
DW 6
DW 7
DW 8
DW 9
DW 10
DW 11
DW 12
DW 13
DW 14
DW 15
DW 16
Variable
DW 17
DW 18
DW 19
DW 20
DW 21
1
31-30 E
I
2
29-28 E
J
3
27-26 E
K
4
25-24 E
L
5
23-22 F
M
6
21-20 F
N
7
19-18 F
O
8
17-16 F
P
9
15-14 G
Q
10
13-12 G
R
11
11-10 G
S
12
9-8 G
T
13
7-6 H
V
14
5-4 H
W
15
3-2 H
X
16
1-0 H
Y
High
Low
Action
0
0
Clear the variable
0
1
Load the variable
1
0
Not modified
1
1
Not modified
Variable 1 is located in
the position which is
furthest left of the text.
The values of the
variables must be
coded in ASCII code.
CHAPTER 4
OPERATION
4-7
DT-203NP, DT-105NP and DT-110NP display series
4.5.4 Message and variable management
Two types of messages can be managed. Messages without variables and messages with
variables.
To display the text of messages without variables, the number of the message must be coded
in hexadecimal in bytes C and D of register DW1, with bytes A and B equal to 0.
Example:
In messages without variables, the other registers are not used but must also be configured
for the exchange of data with the Profibus network.
See 4.5 GSD module installation.
In messages with variables, the values of the variables must be coded as well as the message
code. In displays with 1 to 4 lines, the values of the variables of all the lines can be coded together,
although two steps must be taken in displays with 5 or more lines:
1– Code the values of the variables of lines 1 to 4 with DW1-B = 0
2– Code the values of the variables of lines 5 to 8 with DW1-B = 1 Where the display
does not have 8 lines, the variables not used are rejected.
Once the values have been loaded, those of one part (lines 1 to 4 or 5 to 8) can be modified
without having to modify those of the other (lines 1 to 4 or 5 to 8).
Example:
6-line display. A part counter that is constantly increasing is displayed in line 5. Lines 5
and 6 can be continuously updated without having to update lines 1 to 4.
4.5.5 Variable control register
The variable control register makes variable handling easier. 3 values can be coded for each
variable on each line.
Value = 00: Deletes the value of the variable on the display.
Value = 01: Loads the value of the variable in ASCII code.
Value = 10: Does not modify the value of the variable.
Value = 11: Does not modify the value of the variable.
4.5.6 Register DW1-A = 1. Functions of bytes B, C and D of register DW1.
If register DW1-A is equal to 1, the text sent in the data registers is displayed.
Maximum 20 characters per line.
DW1-B: On displays with over 4 lines, an indication must be given as to whether the
information on the frame is for the 4 upper lines or the 4 lower.
DW1-B = 0 Data for the 4 upper lines and displays of 1 to 4 lines.
DW1-B = 1 Data for the 4 lower lines. Displays of 5 to 8 lines.
DW1-C: Not used
DW1-D: Not used
High
Low
Action
0
0
Clear the variable
0
1
Load the variable
1
0
Not modified
1
1
Not modified
4-8 OPERATION CHAPTER 4
DT-203NP, DT-105NP and DT-110NP display series
4.5.7 Message text.
The texts of the messages on each line must be in ASCII code in registers DW2 to DW21. Depending
on the number of lines on the equipment.
Examples:
1 line display: DW1-B = 0. Data from DW2 to DW6
3 lines display: DW1-B = 0. Line 1 data from DW2 to DW6.
Line 2 data from DW7 to DW11.
Line 3 data from DW12 to DW16.
6 lines display: DW1-B = 0. Line 1 data from DW2 to DW6.
Line 2 data from DW7 to DW11.
Line 3 data from DW12 to DW16.
Line 4 data from DW17 to DW21.
DW1-B = 1 Line 5 data from DW2 a DW6.
Line 6 data from DW7 a DW11.
4.5.8 Register DW1-A = 2. Control commands.
Using the control commands, the internal clock can be adjusted and the brightness of the leds
can be modified.
DW1-B: The type of command is coded in byte DW1-B.
DW1-B = 1C (Hexadecimal) To adjust the internal calendar clock.
DW1-B = 22 (Hexadecimal) To adjust the brightness level of the leds.
DW1-C: Not used
DW1-D: Not used
4.5.8.1 Adjusting the internal calendar clock.
The data regarding the new time and date must be entered in registers DW2, DW3 and DW4 in the
following format:
The values must be in ASCII code.
The clock is updated by resetting the seconds to zero when the frame is received. Although
the frame is maintained, the clock is not updated until a change in any of the values is detected.
4.5.8.2 Modify the display brightness
To modify the display brightness use the first byte of DW2 register. The value must be in
ASCII code.
The value for the minimum brightness is 1.
The value for the maximum brightness is 8.
DW 2
DW 3
DW 4
D
D
Mo
Mo
Y
Y
H
H
Mi
Mi
D = Day H = Hour
Mo = Month Mi =
Minute
Y = Year
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
in altre lingue
- English: Ditel DT-NP
Altri documenti
-
YASKAWA VIPA System SLIO Manuale utente
-
VIPA CPU 013-CCF0R00 Manuale del proprietario
-
-
-
-
Datalogic DS6500 Series Guida di riferimento
-
-
Datalogic DS6300 Guida di riferimento
-
AVENTICS Bus module, PROFIBUS DP, BDC, B-design Manuale del proprietario
-