Tascam 12 Manuale del proprietario

Marca: Tascam

Modello: 12

Categoria: Apparecchiature di registrazione

Tipo: Manuale del proprietario

042100800

Model 12

Multitrack Recording Console

OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

For U.S.A.

Declaration of Conformity

Model Number: Model 12

Trade Name: TASCAM

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1 Santa Fe Springs,

California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

INFORMATION TO THE USER

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to

try to correct the interference by one or more of the following

measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and

receiver.

c) Connect the equipment into an outlet on a circuit dierent

from that to which the receiver is connected.

d) Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modications to this equipment not expressly

approved by TEAC CORPORATION for compliance could void

the user’s authority to operate this equipment.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A

LA NORME NMB-003 DU CANADA.

This product complies with the European

Directives request and the other Commission

Regulations.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including ampliers)

that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not t into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specied by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing

isrequired when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus,

the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

• The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the

ON position.

• The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

• Caution should be taken when using earphones or

headphones with the product because excessive sound

pressure (volume) from earphones or headphones can cause

hearing loss.

• If you are experiencing problems with this product, contact

TEAC for a service referral. Do not use the product until it has

been repaired.

2 TASCAM Model 12

IMPORTANT SAFETY INSTRUCTIONS

WARNING

• To prevent possible hearing damage, do not listen at

high volume levels for long periods.

CAUTION

• Do not expose this apparatus to drips or splashes.

• Do not place any objects lled with liquids, such as vases,

on the apparatus.

• Do not install this apparatus in a conned space such as a

book case or similar unit.

• The apparatus should be located close enough to the AC

outlet so that you can easily grasp the power cord plug at

any time.

• If the product uses batteries (including a battery pack

or installed batteries), they should not be exposed to

sunshine, re or excessive heat.

• CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace only

with the same or equivalent type.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

(a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the

municipal waste stream via collection facilities designated

by the government or local authorities.

(b) By disposing of electrical/electronic equipment and

waste batteries/accumulators correctly, you will help save

valuable resources and prevent any potential negative

eects on human health and the environment.

and batteries/accumulators can have serious eects on the

environment and human health because of the presence

of hazardous substances in the equipment.

(d) The Waste Electrical and Electronic Equipment

(WEEE) symbols, which show wheeled bins that

have been crossed out, indicate that electrical/

electronic equipment and batteries/accumulators

must be collected and disposed of separately

from household waste.

If a battery or accumulator contains more than

the specied values of lead (Pb), mercury (Hg),

and/or cadmium (Cd) as dened in the Battery

Directive (2006/66/EC, 2013/56/EU), then the

chemical symbols for those elements will be

indicated beneath the WEEE symbol.

(e) Return and collection systems are available to end users.

For more detailed information about the disposal of old

electrical/electronic equipment and waste batteries/

accumulators, please contact your city oce, waste

disposal service or the shop where you purchased the

equipment.

Pb, Hg, Cd

TASCAM Model 12 3

IMPORTANT SAFETY INSTRUCTIONS

For China

“仅适用于海拔2000m以下地区安全使用”

“仅适用于非熱帯气候条件下安全使用”

“環境保護使用年限”

产品有毒有害物质或元素的名称及含量

机种: Model 12 有毒有害物质或元素

品名

铅

(Pb)

汞

(Hg)

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

1 CHASSIS部份 ○ ○ ○ ○ ○ ○

2 FRONT PANEL部份 ○ ○ ○ ○ ○ ○

3 螺丝部份 ○ ○ ○ ○ ○ ○

4 线材部份 ○ ○ ○ ○ ○ ○

5 PCB Assy部份 × ○ ○ ○ ○ ○

6 电源部份 × ○ ○ ○ ○ ○

7 附属品部份 × ○ ○ ○ ○ ○

8 LABEL部份 ○ ○ ○ ○ ○ ○

9 包装部份 ○ ○ ○ ○ ○ ○

○ ：表示该有毒有害物质在该部件所有均质材料中的含有量均在 GB/T26572 标准规定的限量要求以下。

× ：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GB/T26572标准规定的限量要求。

（针对现在代替技术困难的电子部品及合金中的铅)

4 TASCAM Model 12

Wireless equipment precautions

Compliance of radio transmitter and

interference

This product has the function of broadband transmitter using

2.4GHz Band.

Use frequency range: 2400 MHz - 2480 MHz

Maximum output power: Bluetooth® Class 2 (less than 2.5

mW) Please use only in the country where you purchased the

product. Depending on the country, restrictions on the use of

Bluetooth wireless technology might exist.

Model for USA

Declaration of Conformity

Responsible party: TEAC AMERICA, INC.

Address: 10410 Pioneer Blvd. Suite #1 Santa Fe

Springs, California 90670, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part.15 of FCC Rules. Operation is

subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Labeling of authorization

FCC ID: XEG-MODEL12

Model for Canada

Compliance of radio transmitter

This device complies with Industry Canada’s licence-exempt

RSSs.

Operation is subject to the following two conditions:

1) This device may not cause interference

2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

Labeling of authorization

IC: 1559C-MODEL12

Modèle pour le Canada

Conformité de l’émetteur radio

Ce dispositif est conforme à la norme CNR-210 d’Industrie

Canada applicable aux appareils radio exempts de licence. Son

fonctionnement est sujet aux deux conditions suivantes:

1) Le dispositif ne doit pas produire de brouillage

préjudiciable,et

2) Ce dispositif doit accepter tout brouillage reçu, y compris

un brouillage susceptible de provoquer un fonctionnement

indésirable.

Étiquetage d’autorisation

IC: 1559C-MODEL12

Compliance of interference

This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and RSS-102

of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But

it is desirable that it should be installed and operated keeping

the radiator at least 20 cm or more away from person’s body

(excluding extremities: hands, wrists, feet and ankles).

Cet équipement est conforme aux limites d’exposition aux

rayonnements énoncées pour un environnement non contrôlé

et respecte les règles les radioélectriques (RF) de la FCC

lignes directrices d’exposition et d’exposition aux fréquences

radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet

une énergie RF très faible qui est considérée conforme sans

évaluation de l’exposition maximale autorisée. Cependant, cet

équipement doit être installé et utilisé en gardant une distance

de 20 cm ou plus entre le dispositif rayonnant et le corps (à

l’exception des extrémités : mains, poignets, pieds et chevilles).

Conformité de brouillage

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Marquage d’autorisation

CAN ICES-3(B)/NMB-3(B)

Model for EEA (European Economic Area)

Hereby, TEAC Corporation declares that the

radio equipment type is in compliance with

Directive 2014/53/EU., and the other Directives,

and Commission Regulations.

The full text of the EU declaration of conformity is available at

the following internet address: Please contact us by e-mail.

http://tascam.eu/en/kontakt.html

EU Importer: TEAC Europe GmbH

Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany

Radiation Exposure requirements

This equipment meets the regulation, which is recognized

internationally, for the case of human exposure to radio waves

generated by the transmitter.

Statement of compliance

Model for USA

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio

frequency Exposure Guidelines.

Model for Canada

This equipment complies with IC RSS-102 radiation exposure

limits set forth for an uncontrolled environment.

Model for USA/Canada

This Class B digital apparatus complies with Canadian ICES-003.

This equipment complies with FCC/IC radiation exposure

limits set forth for an uncontrolled environment and meets

the FCC radio frequency (RF) Exposure Guidelines and RSS-102

of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But

it is desirable that it should be installed and operated keeping

the radiator at least 20 cm or more away from person’s body

(excluding extremities: hands, wrists, feet and ankles).

Model for EEA (European Economic Area)

This equipment complies with EN.62311; Assessment of

electronic and electrical equipment related to human exposure

restrictions for electromagnetic elds; the harmonised standard

of DIRECTIVE 2014/53/EU.

TASCAM Model 12 5

Contents

IMPORTANT SAFETY INSTRUCTIONS ...................................... 2

Wireless equipment precautions ............................................ 5

1 - Introduction ......................................................................... 8

Features ...................................................................................................... 8

Items included with this product ...................................................... 8

Conventions used in this manual ...................................................... 8

Trademarks ................................................................................................ 9

Precautions for placement and use .................................................. 9

Beware of condensation ....................................................................... 9

Cleaning the unit ..................................................................................... 9

About SD cards.......................................................................................10

Precautions for use .........................................................................10

SD card write protection ..............................................................10

Note about formatting .................................................................. 10

Bluetooth® ...............................................................................................10

Proles ................................................................................................. 10

Codecs ................................................................................................. 10

Content protection .........................................................................10

Transmission security ....................................................................10

Using the TEAC Global Site ................................................................11

Product registration .............................................................................11

About TASCAM customer support service ................................... 11

2 - Names and Functions of Parts .......................................... 12

Top panel ..................................................................................................12

Input channel mixing section-1 .................................................12

Input channel mixing section-2 .................................................13

Equalizer section .............................................................................14

Screen operation section .............................................................14

Monitoring section ......................................................................... 15

Analog output adjustment section ..........................................16

Rear panel ................................................................................................17

Home Screen ...........................................................................................18

Meters Screen ......................................................................................... 19

Meter Screen details.......................................................................19

Menu structure .......................................................................................20

Basic MENU screen operations ......................................................... 21

Menu operation procedures .......................................................21

3 - Preparation ........................................................................ 22

Connecting the power supply and other equipment ..............22

Connecting the power ..................................................................23

Connecting microphones ............................................................23

Connecting guitars, basses and similar instruments .........23

Connecting electronic devices and other audio

equipment ......................................................................................... 23

Connecting smartphones/portable audio players .............23

Connecting monitor speakers .................................................... 23

Connecting headphones ..............................................................23

Connecting a computer ................................................................23

Connecting with Bluetooth devices .........................................24

Inserting and removing SD cards .................................................... 24

Inserting SD cards ...........................................................................24

Removing SD cards.........................................................................24

SD card write protection switches ............................................ 24

Turning the power on and o ...........................................................24

Setting the built-in clock date and time .......................................25

Adjusting the display ...........................................................................26

Adjusting the display contrast ...................................................26

Adjusting the display brightness...............................................26

Preparing an SD card for use ............................................................. 26

4 - Managing Songs ................................................................ 27

Viewing the song list ............................................................................ 27

Song Operation ......................................................................................27

Creating a New Song ...........................................................................27

Loading Songs ........................................................................................28

Saving the current song ......................................................................28

Viewing song information .................................................................28

Clearing all marks .................................................................................. 28

Deleting songs .......................................................................................28

Protecting/unprotecting songs .......................................................29

Editing song names ..............................................................................29

Editing text ........................................................................................29

Loading songs created on dierent TASCAM Model series

products ...................................................................................................30

5 - Basic recording .................................................................. 31

Selecting the input source ................................................................. 31

Setting the MODE switch ...................................................................31

Setting phantom power .....................................................................31

Monitoring ...............................................................................................31

SIG indicators and level meters ........................................................ 32

Recording ................................................................................................. 32

Undoing operations .............................................................................33

Undoing the previous operation ............................................... 33

Using the built-in eects ....................................................................33

Setting the built-in eect .............................................................33

Using the library ..............................................................................34

6 - Recorder functions ............................................................ 35

Locate function ......................................................................................35

Changing the playback position ...............................................35

Using the direct locate function to locate ..............................35

Repeat playback function ..................................................................35

Punch in/out function .........................................................................35

Using the footswitch to punch in/out .....................................35

Automatic punch in/out function ................................................... 36

Setting the punch in/out points ................................................ 36

Setting a pre roll point ..................................................................36

Rehearsing punching in and out ............................................... 36

Using automatic punching in and out ....................................37

7 - Track editing ...................................................................... 38

Clearing tracks ........................................................................................ 38

Importing tracks ....................................................................................38

Swapping tracks ....................................................................................39

Stereo mix export function ................................................................39

8 - Mark functions ................................................................... 40

Using mark functions ...........................................................................40

Adding marks .........................................................................................40

Moving between marks ......................................................................40

Clearing individual marks...................................................................40

9 - Other functions .................................................................. 41

Metronome functions ..........................................................................41

Setting the click sound ..................................................................41

Making metronome settings ......................................................42

Setting the count in function .....................................................43

Starting and stopping the metronome manually ............... 43

Function button setting ................................................................43

MIDI functions ........................................................................................ 44

Setting MIDI time code operation ............................................44

Setting MIDI CLOCK/SPP ...............................................................44

Mixer functions ......................................................................................45

Selecting the positions that recording signals are sent

from each channel ..........................................................................45

6 TASCAM Model 12

Contents

Setting the phase of each channel ...........................................45

Changing the positions that signals are sent to the AUX 1

bus from each channel ..................................................................46

Setting the solo function for all channels ..............................46

Footswitch functions ...........................................................................47

Setting up the footswitch ............................................................47

Setting the footswitch polarity ..................................................47

DAW CONTROL .......................................................................................47

10 - Settings and Information ................................................ 48

Viewing information ............................................................................48

CARD Screen .....................................................................................48

SONG Screen .....................................................................................48

FIRMWARE Screen ........................................................................... 48

Setting the song name format .........................................................48

Setting the WORD item ................................................................. 48

Restoring factory default settings ...................................................49

Formatting SD cards .............................................................................49

Playing WAV les on SD cards (SD PLAY mode) ..........................50

11 - Using a computer to transfer data ................................. 51

Connecting with a Computer ...........................................................51

Disconnecting ..................................................................................52

Loading WAV les from a computer ...............................................52

12 - USB audio interface functions ........................................ 53

Installing the dedicated software ...................................................53

Installing the Windows dedicated software .......................... 53

Installing the Mac dedicated software .................................... 54

Working with Gatekeeper ............................................................ 54

Uninstalling the dedicated software ..............................................55

Uninstalling the Windows dedicated software ....................55

Uninstalling the Mac dedicated software ..............................55

Opening the Settings Panel...............................................................55

Windows .............................................................................................55

Mac ....................................................................................................... 55

Settings Panel overview......................................................................56

Notication function ............................................................................56

Setting Sound Properties ...................................................................56

Simultaneous ASIO/WDM playback ...............................................57

USB audio mode .................................................................................... 57

13 - MIDI Implementation Chart ............................................ 58

14 - Messages .......................................................................... 59

15 - Troubleshooting .............................................................. 61

16 - Specications ................................................................... 62

General ......................................................................................................62

Inputs and outputs ............................................................................... 62

Analog audio input and output ratings .................................. 62

Control input/output .....................................................................62

Computer system requirements ...................................................... 63

Windows .............................................................................................63

Mac ....................................................................................................... 63

iOS device ..........................................................................................63

Supported audio drivers ...............................................................63

Audio performance ..............................................................................63

Bluetooth .................................................................................................64

Other ..........................................................................................................64

Dimensional drawings .........................................................................64

Block diagram ......................................................................................... 65

Level diagram .........................................................................................66

TASCAM Model 12 7

1 - Introduction

Thank you very much for purchasing the TASCAM Model 12

Multitrack Recording Console.

Before using this unit, read this Owner’s Manual carefully so that

you will be able to use it correctly and enjoy working with it for

many years. After you have nished reading this manual, please

keep it in a safe place for future reference.

You can also download this Owner’s Manual from the TEAC

Global Site (http://teac-global.com/).

Features

o TASCAM Ultra-HDDA mic preamps built-in (for channels 1–6)

o 10 input digital mixer with 10 line and 8 mic inputs

o Multitrack recording and playback with 12-track recording

(input channels 1–6, 7/8, 9/10 and MAIN MIX L/R bus

channels 11–12)

o USB audio interface functions built-in

i 12 tracks (10 input channels and MAIN MIX L/R bus) can

be input to the computer

i 10 track outputs and computer outputs can be assigned

to channel inputs (channels 1–6, 7/8, 9/10)

i Supports USB 2.0 audio with resolutions up to 24-bit and

48kHz sampling frequency

o Digital compressors included on channel 1–6, 7/8 and 9/10

inputs

o 60mm faders enable precise adjustments

o MIC/LINE (BAL)/INST TRS input jacks support high impedance

(Hi-Z) on every channel

o Channel inserts (INSERT) on channels 1-2

o Multiple buses include stereo main (MAIN MIX L/R bus), sub

(SUB L/R bus) and AUX (AUX 1 and AUX 2/FX)

o 2 AUX sends (AUX 1/AUX 2)

o Input channels have 3-band semi-parametric EQs with

adjustable mid frequencies

o 4-band semi-parametric equalizer for output

o 16 TASCAM preset eects can be used for a variety of

applications

o Multitrack recording and playback possible using SD cards

o Bluetooth® audio playback and recording supported

o Punching in and out function per track (including punching

in and out automatically and with footswitches)

o SD/SDHC cards and SDXC cards (Class 10 or more)

o Multiple footswitch functions available (select play/pause,

eect muting or punch in/out)

o 2 built-in PHONES outputs (level adjustment and SOLO L/R

bus monitoring can be enabled separately)

o DAW control with HUI/MCU emulation supported by major

DAWs

o CLICK output that supports TAP TEMPO

o MIDI input and output connectors enable connection with

keyboards and other MIDI devices

Items included with this product

This product includes the following items.

Take care when opening the package to avoid damaging the

items. Keep the packing materials for transportation in the

future. Please contact the store where you purchased this unit

if any of these items are missing or have been damaged during

transportation.

o Main unit .................................................................................................x 1

o AC adaptor (TASCAM PS-M1524A) ................................................. x 1

o Cord for AC adapter (JAPAN USA/EUROPE/AUSTRALIA) ........ x 3

o Owner’s Manual (this document) including warranty ............ x 1

ATTENTION

Always use the included AC adapter (PS-M1524A) and AC

adapter power cord with this unit. Never use the included AC

adapter or AC power cord with any other device. Doing so

could cause damage, re or electric shock.

Conventions used in this manual

In this manual, we use the following conventions:

o The four buttons under the display are called the function

buttons. From left to right, they are shown as buttons F1, F2,

F3 and F4. Moreover, the functions at the bottoms of the

screens will be shown after the button names.

Examples: F1 button, F4 button

o SD/SDHC/SDXC memory cards are referred to as “SD cards”.

o Computers, portable audio devices and other equipment

connected to this unit using Bluetooth are called “Bluetooth

devices”.

o Groups of recorded data are referred to as “songs”.

o The song that is currently selected is called the “current song”.

o Information shown on a computer display is written like this:

“ O K ”.

o As necessary, additional information is provided under TIP,

NOTE and CAUTION headings.

TIP

These are tips about how to use the unit.

NOTE

These provide additional explanations and describe special

cases.

ATTENTION

Failure to follow these instructions could result in damage to

equipment or lost data, for example.

CAUTION

Failure to follow these instructions could result in injury.

8 TASCAM Model 12

1 - Introduction

Trademarks

o TASCAM is a registered trademark of TEAC Corporation.

o SDXC Logo is a trademark of SD-3C, LLC.

o The Bluetooth® word mark and logo are the property of

Bluetooth SIG, Inc. and are used by TEAC Corporation with

permission.

o Microsoft, Windows and Windows Media are either registered

trademarks or trademarks of Microsoft Corporation in the

United States and/or other countries.

o Apple, Mac, macOS, App Store and iTunes are trademarks of

Apple Inc. in the United States and other countries.

o ASIO is a trademark of Steinberg Media Technologies GmbH.

o Other company names, product names and logos in this

document are the trademarks or registered trademarks of

their respective owners.

Information is given about products in this manual

only for the purpose of example and does not indicate

any guarantees against infringements of third-party

intellectual property rights and other rights related to

them. TEAC Corporation will bear no responsibility for

infringements on third-party intellectual property rights

or their occurrence because of the use of these products.

Properties copyrighted by third parties cannot be used for

any purpose other than personal enjoyment and the like

without the permission of the right holders recognized by

TEAC Corporation will bear no responsibility for rights

infringements committed by users of this product.

Precautions for placement and use

o The operating temperature range of this unit is 5 - 35 °C.

o Do not install this unit in the following types of locations.

Doing so could make the sound quality worse or cause

malfunction.

Places with signicant vibrations

Next to a window or in another location exposed to direct

sunlight

Near heaters or other extremely hot places

Extremely cold places

Very humid or poorly ventilated places

Very dusty places

o To enable good heat dissipation, do not place anything on

top of the unit.

o Do not place the unit on top of a power amplier or other

device that generates heat.

Beware of condensation

Condensation could occur if the unit is moved from a cold place

to a warm place, it is used immediately after a cold room has

been heated or it is otherwise exposed to a sudden temperature

change.

To prevent this, or if this occurs, let the unit sit for one or two

hours at the new room temperature before using it.

Cleaning the unit

Use a dry soft cloth to wipe the unit clean. Do not wipe

with chemical cleaning cloths, thinner, alcohol or other

chemical agents. Doing so could damage the surface or cause

discoloration.

TASCAM Model 12 9

1 - Introduction

About SD cards

This unit uses SD cards for recording and playback.

This unit can use SD cards that are Class 10 or higher and

compatible with SD, SDHC or SDXC standards.

A list of SD cards that have been conrmed for use with this unit

can be found on our web site. Please access to a product page of

this product from the TEAC Global Site (http://teac-global.com)

to nd the list or contact the TASCAM customer support service.

Precautions for use

SD cards are delicate media.

In order to avoid damaging SD cards, please take the following

precautions when handling them.

o Do not leave them in extremely hot or cold places.

o Do not leave them in extremely humid places.

o Do not let them get wet.

o Do not put things on top of them or twist them.

o Do not hit them.

o Do not remove or insert them during recording, playback,

data transmission or other access.

o When transporting them, put them into cases, for example.

SD card write protection

This unit writes track information to the media in order

to improve operation performance. Since, for example,

setting information cannot be written to SD cards that are

writeprotected, settings will not be retained when the unit is

restarted and performance will be otherwise aected.

Note about formatting

SD cards formatted by this unit are optimized to improve

performance during recording. Use this unit to format the SD

cards to be used with it. Errors might occur when recording with

this unit using an SD card formatted by a computer or other

device.

Bluetooth®

This unit has a built-in Bluetooth audio receiver, and can input

sound played on a computer or portable audio device that

supports Bluetooth (Bluetooth device).

ATTENTION

The Bluetooth function of this unit is not guaranteed to

enable connection or operation with all Bluetooth devices.

Proles

This unit supports the following Bluetooth proles.

o A2DP (Advanced Audio Distribution Prole)

In order to transfer audio by Bluetooth, the Bluetooth device

must support A2DP.

Even if a Bluetooth device supports the same proles, though,

its functions might dier according to its specications.

Codecs

This unit supports the following codecs. It will automatically

select one of them during audio transfer.

o SBC

o AAC

The unit will select the appropriate codec to use according

to the codec compatibility of the other Bluetooth device and

communication conditions.

NOTE

i You cannot select the codec to be used by pressing a button,

for example.

i Due to characteristics of Bluetooth wireless technology,

playback from this unit will be slightly delayed compared to

playback from the Bluetooth device.

Content protection

This unit supports SCMS-T as a form of content protection when

transmitting audio, so it can play protected audio.

Transmission security

This unit supports security functions during Bluetooth

transmission in accordance with the Bluetooth standard

specications, but it does not guarantee the privacy of such

transmissions.

TEAC CORPORATION will bear no responsibility should an

information leak occur during transmission by Bluetooth.

10 TASCAM Model 12

1 - Introduction

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global

Site:

http://teac-global.com/

In the TASCAM Downloads section, select the desired language

to open the Downloads website page for that language.

Product registration

Customers in the USA, please visit the following TASCAM

website to register your TASCAM product online.

https://tascam.com/us/

About TASCAM customer support

service

TASCAM products are supported and warrantied only in their

country/region of purchase.

To receive support after purchase, on the TASCAM Distributors

list page of the TEAC Global Site (http:// teac-global.com/),

search for the local company or representative for the

region where you purchased the product and contact that

organization.

When making inquiries, the address (URL) of the shop or

web shop where it was purchased and the purchase date are

required.

Moreover, the warranty card and proof of purchase might also

be necessary.

TASCAM Model 12 11

2 - Names and Functions of Parts

Top panel

a Input channel mixing section-1

Use this section to adjust the input levels of each channel.

b Input channel mixing section-2

Use this section to choose input sources for each channel,

adjust compressors and equalizers, and set levels sent to

each bus (MAIN MIX L/R, SOLO L/R, AUX1, AUX2/FX, SUB L/R).

(see “Input channel mixing section-2” on page 13)

c Equalizer section

Use this section to connect headphones and adjust the output

equalizer. (see “Equalizer section” on page 14)

d Screen operation section

Use this section to operate the meter, home and MENU

screens shown on the display. (see “Screen operation section”

on page 14)

e Monitoring section

Switch Bluetooth device input destinations, switch

monitoring destinations, and adjust AUX OUTPUT AUX 1/2

jack output levels. (see “Monitoring section” on page 15)

f Analog output adjustment section

Adjust the output levels of the built-in eects, and the

MAIN OUTPUT and SUB OUTPUT jacks. (see “Analog output

adjustment section” on page 16)

Input channel mixing section-1

1 GAIN knobs and SIG indicators (1-6, 7/8-9/10)

Use the GAIN knobs to adjust the input levels of each

channel.

its SIG indicator will light green when a signal is input (-40dB

or higher).

If a SIG indicator stays lit red continuously, lower the GAIN

knob.

2 LOW CUT switches (1-6, 7/8-9/10)

Turn this switch on (pushed in) to enable low cut lters that

cut noise and other sounds at low frequencies.

3 INST switches (1-6, 7/8-9/10)

Set according to the MIC/LINE (BAL)/INST TRS input jack input

sources.

Turn the INST switch on (pushed in) when connecting an

guitar, bass or other equipment with high output impedance.

Turn the INST switch o (not pushed in) when connecting

electronic instruments, audio devices, mics and other

equipment.

12 TASCAM Model 12

2 - Names and Functions of Parts

Input channel mixing section-2

4 MODE switches (1-6, 7/8-9/10)

Use these to select the input source for each channel. (see

“Setting the MODE switch” on page 31)

5 COMP knobs and indicators (1-6, 7/8-9/10)

Use these knobs to adjust the compression thresholds for the

signals input to each channel.

When compression is activated, the COMP indicators light.

6 EQ knobs (1-6, 7/8-9/10)

i Use these to boost and attenuate the HIGH, MID and LOW

bands of each channel.

Setting range: ±15 dB

i The central frequencies of the MID bands can be set.

Setting range: 100 Hz - 8 kHz (default: 600Hz)

7 AUX 1 knobs (1-6, 7/8-9/10)

Use these to adjust the levels of signals sent to the AUX 1 bus.

8 POST indicator (shared by all channels)

When this indicator is lit, signals are sent to the AUX 1 bus

after the channel faders. (see “Changing the positions that

signals are sent to the AUX 1 bus from each channel” on page

46)

9 AUX2/FX knobs (1-6, 7/8-9/10)

Use to adjust the levels of the signals sent to the AUX2/FX

bus.

0 PAN knobs (1-6, 7/8-9/10)

Use to adjust the stereo positions of the signals input to each

channel.

NOTE

i When PAN knobs are centered (C), signals are reduced by 3

dB and sent to both left and right MAIN MIX L/R buses.

i When a PAN knob is turned all the way to the left (L), that

channel signal is sent only to the left MAIN MIX L/R bus. It is

not sent to the right bus.

i When a PAN knob is turned all the way to the right (R), that

channel signal is sent only to the right MAIN MIX L/R bus. It is

not sent to the left bus.

q REC buttons and indicators (1-6, 7/8-9/10)

Use these to select the channels to record to the SD card.

w MUTE switches and indicators (1-6, 7/8-9/10)

When these switches are on (pushed in, MUTE indicator lit),

those channels are muted.

e Channel faders (1-6, 7/8-9/10)

Use these to adjust the send levels of channel signals.

r MAIN switches (1-6, 7/8-9/10)

Turn these switches on (pushed in) to send channel signals to

the MAIN MIX L/R bus.

t SUB switches (1-6, 7/8-9/10)

Turn these switches on (pushed in) to send channel signals to

the SUB L/R bus.

y SOLO switches (1-6, 7/8-9/10)

Turn these switches on (pushed in) to send channel signals to

the SOLO L/R bus.

When these switches are on, the sound of their channels can

be heard through the SOLO L/R bus with headphones.

When the SOLO MODE screen setting is INPLACE SOLO,

the signals of channels that are not on will be muted. (see

“Setting the solo function for all channels” on page 46)

TASCAM Model 12 13

2 - Names and Functions of Parts

Equalizer section

u MASTER SECTION EQ knobs

This 3-band semi-parametric equalizer aects signals output

from the MAIN OUTPUT and AUX OUTPUT AUX 1/2 jacks.

i / switch

This sets the acuteness of the MID band of the semi-

parametric equalizer.

Button Meaning

On ( )

The band is acute, making it aect a

narrower frequency band.

O ( )

The band is less acute, making it aect a

broader frequency band.

o PHONES jack (1/2)

Use this standard stereo jack to connect stereo headphones.

Use an adapter to connect headphones with a mini plug.

Use these to monitor signals from the MAIN MIX L/R, AUX 1,

AUX 2/FX and SOLO L/R buses. (see “Block diagram” on page

65)

p PHANTOM +48V switch and indicator

Use this switch to supply +48V phantom power to the 1–6,

7/8 and 9/10 XLR jacks on the back of the unit.

The indicator lights when the PHANTOM +48V switch is set to

on (pushed in). (see “Setting phantom power” on page 31)

a SD card slot

Insert SD cards in this slot. (see “Inserting and removing SD

cards” on page 24)

s AUX 1/2/MAIN MIX switch

Set which output signals are aected by the equalizer.

AUX 1/2: Equalizer is applied to signals sent from the AUX

1 and AUX 2/FX buses.

MAIN MIX: Equalizer is applied to signals sent from the

MAIN MIX L/R bus.

NOTE

Also set the EQ IN/BYPASS switch to “EQ IN”.

d EQ IN/BYPASS switch

When this switch is EQ IN, the equalizer will aect the output

signals set with the AUX 1/2/MAIN MIX switch.

When set to BYPASS, the equalizer will not be applied

regardless of the AUX 1/2/MAIN MIX switch setting.

Screen operation section

f Display

Shows a variety of information.

g USB indicator

This lights when the USB connection is working.

h PFL/AFL indicator

This indicator lights when at least one channel SOLO switch

is on or when the AFL switch for the AUX 1 or AUX 2 knob or

the FX fader is on.

j Function buttons

The functions of these buttons change depending on the

screen shown on the display. The functions shown at the

bottom of the display are the currently assigned functions.

NOTE

For convenience, the four buttons under the display are

called the function buttons in this manual. From left to right,

they are called the F1, F2, F3 and F4 buttons.

k MULTI JOG dial

This dial functions as a dial when turned and as a button

when pressed.

Dial functions

i Turn when the Home Screen is open to move the le

playback position. (see “Locate function” on page 35)

i When a MENU Screen is open, turn to select items and

change setting values. (see “Basic MENU screen operations”

on page 21)

Button function

i Press when the Home Screen is open to designate a locate

point. (see “Locate function” on page 35)

i When a Menu Screen is open, press to conrm selections

and settings (ENTER button function).

l Output level indicators

These show the output levels of the MAIN OUTPUT jacks.

When the PFL/AFL indicator is lit, these show the output

levels from the SOLO L/R bus.

14 TASCAM Model 12

2 - Names and Functions of Parts

; m/, buttons

i When stopped and during playback, press and hold these

buttons to search backward/forward.

i When the Home Screen is open, press the m button

to locate to the beginning of the current song (00:00:00,

which is the zero point).

i When the Home Screen is open, press the , button to

locate to the end of the current song.

i If the current song has auto punch in or out points set, you

can also locate to those points.

i If the current song has marks set, these can also be used to

locate to them.

i While pressing the 8 button, press the m button to

locate to the point where recording last started.

i While pressing the 8 button, press the , button to

locate to the point where recording last stopped.

i When the SD PLAY Screen is in playback state, press to skip

a le. (see “Playing WAV les on SD cards (SD PLAY mode)”

on page 50)

z MENU button

i When the Meter Screen is open, press to open the Home

Screen.

i When the MENU Screen or a menu item settings screen is

open, press to return to the Home Screen.

i When the Home Screen is open, press to open the MENU

Screen. (see “Menu structure” on page 20) and (see “Basic

MENU screen operations” on page 21)

x 8 button/indicator

Press to stop playback or recording.

This button lights when stopped.

Press this button when paused to return to the beginning of

the song or le.

c 7/9 button/indicator

Press this button to start playback.

This button lights during playback and recording.

This button blinks when paused.

v 0 button/indicator

Press this button to start recording.

This button lights during recording.

Press this button during playback to start recording (Manual

punch in).

Monitoring section

b MUTE switch/indicator (AUX 1/AUX 2)

When MUTE switches are on (MUTE indicators lit), signals to

the AUX OUTPUT AUX 1/2 jacks are muted.

n AFL switches (AUX 1/AUX 2)

When these switches are on (pushed in), the AUX OUTPUT

AUX 1/2 jack output signals are sent to the SOLO L/R bus.

When these switches are on, the sound of the SOLO L/R bus

can be heard through headphones.

m PAIRING button and indicator

Press and hold this button to activate Bluetooth pairing

mode.

Press when pairing to end pairing mode. (see “Connecting

with Bluetooth devices” on page 24)

, ASSIGN switch

Sound from the Bluetooth device is sent to channels 9/10

when this switch is set to “9/10” or the MAIN MIX L/R bus

when it is set to “MAIN”.

. AUX 1/AUX 2 knobs

Use to adjust the output levels of the AUX OUTPUT AUX 1/2

jacks.

/ PFL/AFL MASTER knob

Use this to adjust the send level from the SOLO L/R bus.

! SD MAIN MIX RETURN switch

When this switch is on (pushed in), playback of stereo master

les recorded on the SD card is output from the MAIN

OUTPUT jacks.

ATTENTION

Be aware that when this switch is on (pushed in), the sound

of the MAIN MIX L/R bus is not output.

@ PHONES knob (1/2)

Use this to adjust the headphone output level.

CAUTION

Before connecting headphones, minimize the volume with

the PHONES knob. Failure to do so could result in a sudden

loud noise that could harm hearing, for example.

# AUX 1/2 /MAIN switch

Turn these switches on to monitor signals from the AUX 1

and AUX 2/FX buses.

TASCAM Model 12 15

2 - Names and Functions of Parts

Analog output adjustment section

$ MUTE switch and indicator (FX)

When the MUTE switch are on (pushed in, MUTE indicator lit),

the signal from the built-in eect is muted.

% MUTE switches and indicators (SUB, MAIN)

When MUTE switches are on (MUTE indicators lit), signals to

the SUB OUTPUT/MAIN OUTPUT jacks are muted.

^ TEMPO indicator

i This lights green when a song that has click sound output

set is loaded.

i When the metronome is operating, it lights or blinks as

follows. (see “Metronome functions” on page 41)

Indicator color Meaning

Red

This color lights on the rst beat of

the setting

Green This blinks at the set tempo

& CLICK button

i When the EFFECT screen is open, tap this button

repeatedly at the desired speed to set the delay of the

built-in eect. (see “Setting the built-in eect” on page

33)

i When the TAP TEMPO screen is open, tap this button

repeatedly at the desired tempo to set the metronome.

(see “Making metronome settings” on page 42)

i Press this button when the metronome is stopped to start

it at the set tempo. Press this button when the metronome

is on to stop it. (see “Starting and stopping the metronome

manually” on page 43)

* FX fader

Use to adjust the levels of signals sent from the built-in eect

to the following buses.

i MAIN MIX L/R bus

i SOLO L/R bus

i AUX1 bus

i SUB L/R bus

( TO AUX 1 knob

Use these to adjust the levels of signals sent from the built-in

eects to the AUX1 bus.

) SELECT button

Open the EFFECT Screen and make built-in eect settings.

(see “Using the built-in eects” on page 33)

The built-in eect return signal is sent to the following buses.

i MAIN MIX L/R bus

i SOLO L/R bus

i AUX1 bus

i SUB L/R bus

Q MAIN switch (FX)

When this switch is on, signals from the built-in eect are

sent to the MAIN MIX L/R bus.

W SUB switch (FX)

When this switch is on, signals from the built-in eect are

sent to the SUB L/R bus.

E AFL switch (FX)

When this switch is on, signals from the built-in eect are

sent to the SOLO L/R bus.

When this switch is on, the sound of the SOLO L/R bus can be

heard with headphones.

R POST REC switch

Select the send position of the signal recorded to the SD

card.

When this switch is on, signals from after the MAIN fader are

recorded to the SD card.

T AUX 1 switch (FX)

When this switch is on, signals from the built-in eect are

sent to the AUX1 bus.

Y MAIN switch (SUB)

When this switch is on (pushed in), the SUB OUTPUT jack

output signal is sent to the MAIN MIX L/R bus.

U SUB fader

Use to adjust the output level of the SUB OUTPUT jacks.

I MAIN fader

Use to adjust the output level of the MAIN OUTPUT jacks.

16 TASCAM Model 12

2 - Names and Functions of Parts

Rear panel

O USB port

This is a USB Type-C port. Use a USB cable (Type-A to Type-C)

to connect the unit to a computer. (see “Connecting with a

Computer” on page 51)

ATTENTION

The unit should be connected directly to the computer, not

through a USB hub. Moreover, noise could be picked up if the

cable is too long.

P MAIN OUTPUT L/R jacks

These analog outputs are XLR jacks.

i XLR (1: GND, 2: HOT, 3: COLD)

A MUSIC/TALK jack (9/10, 4-pole mini jack)

This is a 4-pole mini input/output jack.

By using a cable with a 4-pole mini plug, the signals output

from the MAIN OUTPUT jacks can be sent to the smartphone

while simultaneously receiving input from the smartphone.

S MIC/LINE (BAL)/INST input jacks (7/8-9/10)

These analog inputs are XLR/TRS combo jacks.

i XLR (1: GND, 2: HOT, 3: COLD)

i TRS (Tip: HOT, Ring: COLD, Sleeve: GND)

The balanced XLR jacks are for XLR balanced mic input.

The TRS jacks are for standard TRS stereo line input. If only

the L jack in a pair is connected, the same signal was be sent

to both left and right channels.

When directly connecting a guitar, bass or other instrument,

set the INST switch to on (pushed in).

NOTE

Activating the INST switch only aects the L jack.

D MIC/LINE (BAL)/INST input jacks (1-6)

These analog inputs are XLR/TRS combo jacks.

i XLR (1: GND, 2: HOT, 3: COLD)

i TRS (Tip: HOT, Ring: COLD, Sleeve: GND)

The balanced XLR jacks are for XLR balanced mic input.

The TRS jacks are for standard TRS mono line input.

When directly connecting a guitar, bass or other instrument,

set the INST switch to on (pushed in).

F DC IN 15V connector

Connect the included AC adapter (PS-M1524A) here. (see

“Connecting the power” on page 23)

G STANDBY switch

Press to turn the unit on and o.

CAUTION

Before turning the unit on, lower the volumes of connected

equipment to their minimum levels.

Failure to do so might cause sudden loud noises, which could

harm your hearing or result in other trouble.

NOTE

Do not do this when the unit is operating (including

recording, playing back or writing data to an SD card). Doing

so could cause proper recording to fail and recorded data to

be lost.

H SUB OUTPUT L/R jacks

These standard TRS jacks are analog outputs.

i TRS (Tip: HOT, Ring: COLD, Sleeve: GND)

J AUX OUTPUT AUX 1/2 jacks

These standard TRS jacks are analog outputs.

i TRS (Tip: HOT, Ring: COLD, Sleeve: GND)

ATTENTION

When the AUX OUTPUT AUX 2 jack is in use, the built-in

eects cannot be used. (see “Using the built-in eects” on

page 33)

K CLICK jack

This outputs the metronome click sound. (see “Setting the

click sound” on page 41)

L FOOTSWITCH jack

This standard TRS jack is for connecting a footswitch.

i TRS (Tip: FOOTSW1, Ring: FOOTSW2, Sleeve: GND)

NOTE

i This unit was designed to be used with unlatched

(momentary) footswitches that have to be pushed to

function (shorted when pushed). (see “Setting the footswitch

polarity” on page 47)

i By using a commercially-available splitter cable, two

footswitches can be used.

: MIDI OUT connector

This 5-pin DIN is a standard MIDI output connector.

This outputs MIDI signals sent from the computer.

If the MIDI TIMECODE or MIDI CLOCK/SPP items are set to

ON on the MIDI screen, those will also be output. (see “MIDI

functions” on page 44)

Z MIDI IN connector

This 5-pin DIN is a standard MIDI input connector.

MIDI signals input through this connector will be sent to the

computer.

X INSERT jacks (1-2, standard)

Use these standard TRS jacks to connect external devices

(eects).

i TRS (Tip: SEND, Ring: RETURN, Sleeve: GND)

TASCAM Model 12 17

2 - Names and Functions of Parts

Home Screen

When the Meter Screen is open, press the MENU button to open

the Home Screen.

1 Repeat playback status

An icon appears when the repeat playback function is on.

(see “Repeat playback function” on page 35)

2 Song format

This shows the current song le format.

44.1kHz, 16bit

44.1kHz, 24bit

48kHz, 16bit

48kHz, 24bit

NOTE

If no song is loaded, the operation format of the unit will be

shown like or .

3 Automatic punch in/out function on/o status

The icon appears when the automatic punch in/

out function is on. (see “Automatic punch in/out function” on

page 36)

4 SD card present status

When an SD card is loaded, the icon appears.

When an SD card is protected, the icon appears.

Since system les cannot be updated when the icon

appears, automatic punch in/out settings will not be retained

and previously loaded songs will not be loaded when the

unit is turned on again.

5 USB connection status

During USB connection, the icon appears.

6 Song name

This shows the name of the current song.

If a song is protected, an icon appears before the le name.

(see “Protecting/unprotecting songs” on page 29)

If a song has unsaved marks, an icon appears before the

le name. (see “Adding marks” on page 40)

7 Transport status

This icon shows the recorder operation status.

Indicator Meaning

Stopped at the beginning of the le

Paused

Recording

Playback

8 Playback position

The current playback position is shown by a bar.

9 Automatic punch in/out point setting status

When the automatic punch in/out function is on, these show

the status of automatic punch in/out point setting.

Punch in point

Punch out point

0 Remaining time

The remaining time available for recording on the SD card is

shown (in hours: minutes: seconds).

NOTE

The remaining recordable time on an SD card depends on

the number of recording channels and SD card capacity.

q Built-in eect status

When a built-in eect is on, the number of the eect in use is

shown.

When the built-in eect is o, the icon appears.

When the built-in eect cannot be used, the icon

appears. (see “Using the built-in eects” on page 33)

w Recorder time counter

This shows the elapsed time from the beginning of the song.

e Mark indicators

An icon is shown at each mark.

r Song length

This shows the length of the current song (in hours: minutes:

seconds).

t Function button functions

This shows the functions assigned to the function button on

the Home Screen.

i F1 button: This opens the Meter Screen.

i F2 button: This turns the repeat playback function

on/o.

i F3 button: This returns to the state before the

previous operation.

i F3 button: This restores the state after the previous

operation.

i F4 button: This adds/deletes marks.

i F4 button: Open the METRONOME screen where

metronome functions can be set. (see

“Function button setting” on page 43)

NOTE

i The F3 button and indicators appear when

those operations are possible.

i Set the F4 button function on the KEY FUNCTION screen.

(see “Using mark functions” on page 40) and (see “Function

button setting” on page 43)

18 TASCAM Model 12

2 - Names and Functions of Parts

Meters Screen

This shows the levels of the signals being input to the unit.

1 Transport status

This icon shows the recorder operation status.

2 Recorder time counter

This shows the elapsed time from the beginning of the song.

3 Track level meters

These show the signal levels of each channel.

NOTE

The channels show the MAIN MIX L/R bus levels.

4 Level meter guide

This provides guidance for level adjustment. The guide is

shown at the -12dB level.

5 Function button functions

This shows the functions assigned to the function button on

the Meter Screen.

i F1 Press to change the input sources shown on

the Meter Screen.

i F2 Press to show the level meters for channel

1-8 signals on the Meter Screen.

i F3 Press to show the level meters for channel

9/10 and signals on the Meter Screen.

Meter Screen details

When the Meter Screen is open, press the F1 button to

change the signal sources shown by the meters.

Channel input level screens

The levels of signals input on each channel are shown

depending on their MODE switch settings.

LIVE INPUT Screen

This shows the levels of signals being input to the input jacks.

PC RETURN Screen

This shows the levels of signals output from a computer when

used as a USB audio interface.

NOTE

Output from the computer, including from Windows Media

Player and iTunes, is sent to channels 1-2.

MTR RETURN Screen

This shows the playback signal levels of songs recorded on SD

cards.

Channels that have recording data in the song

Channels that do not have recording data in the

song

TASCAM Model 12 19

2 - Names and Functions of Parts

Menu structure

When the Home Screen is open, press the MENU button to open the MENU Screen.

The various menu items are as follows.

Menu item Function Page

SONG SONG Work with songs on an SD card page 28

CLICK

SETTING Set click sound operation and output destination page 41

METRONOME Make specic metronome settings page 42

COUNT IN Set the count in function page 43

MTR

TRACK EDIT

TRACK CLEAR Clear specic tracks or all tracks page 38

IMPORT Import chosen WAV les to song tracks page 38

TRACK SWAP Swap song recording les page 39

AUTO PUNCH Set the auto punch in/out function page 36

A.PUNCH PRE ROLL Set the pre-roll point page 36

MIDI

MIDI TIME CODE Set the MIDI time code page 44

MIDI CLOCK/SPP Set MIDI clock and song position pointer page 44

MIXER

MTR/USB SEND POINT Set when input signals are sent page 45

PHASE Set the phase of each channel page 45

AUX1 SEND Set the signal sent to the AUX 1 bus page 46

SOLO MODE Set the solo operation page 46

STEREO MIX EXPORT Use stereo mix export function page 39

SD PLAY Play WAV les on an SD card page 50

STORAGE SD cards can be accessed from a computer page 51

DAW CONTROLLER Set the DAW controller mode page 47

SYSTEM

INFORMATION View SD card information, song information and the rmware version page 48

DATE/TIME Date and time settings page 25

SONG NAME Set the song name format page 48

DISPLAY Adjust the display page 26

KEY FUNCTION Set the function of the function button

page 40

page 43

FOOTSW Make footswitch settings page 47

USB AUDIO Make USB audio settings page 57

INITIALIZE Restore factory default settings page 49

MEDIA FORMAT Format the SD card page 49

NOTE

The settings for all menu items are retained even when the unit is turned o.

20 TASCAM Model 12

La pagina sta caricando ...

Tascam 12 Manuale del proprietario

Marca: Tascam

Modello: 12

Categoria: Apparecchiature di registrazione

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Tascam 12 Owner's manual

Tascam 12 Manuale del proprietario

Tascam 12 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti