ESAB A6 TFE1 / TFE2 / TGE1 Manuale utente

Marca: ESAB

Modello: A6 TFE1 / TFE2 / TGE1

Categoria: Sistema di saldatura

Tipo: Manuale utente

Valid for serial no. 725--xxx--xxxx0456 503 001 2004--12--02

A6 Mastertrac

A6 TFE1/A6 TFE2/A6 TGE1

101103105107109111102021110025108024042106023061104022041100020040060001

Bruksanvisning

Brugsanvisning

Bruksanvisning

Käyttöohjeet

Instruction manual

Betriebsanweisung

Manuel d’instructions

Gebruiksaanwijzing

Instrucciones de uso

Istruzioni per l’uso

Manual de instruções

Ïäçãßåò ÷ñÞóåùò

-- 2 --

Rätt till ändring av specifikationer utan avisering förbehålles.

Ret til ændring af specifikationer uden varsel forbeholdes.

Rett til å endre spesifikasjoner uten varsel forbeholdes.

Oikeudet muutoksiin pidätetään.

Rights reserved to alter specifications without notice.

Änderungen vorbehalten.

Sous réserve de modifications sans avis préalable.

Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.

Reservado el derecho de cambiar las especificaciones sin previo aviso.

Specifiche senza preavviso.

Reservamo--nos o direito de alterar as especificações sem aviso prévio.

Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.

SVENSKA 5..............................................

DANSK 22................................................

NORSK 39................................................

SUOMI 56................................................

ENGLISH 73..............................................

DEUTSCH 90.............................................

FRANÇAIS 107.............................................

NEDERLANDS 124.........................................

ESPAÑOL 141..............................................

ITALIANO 158..............................................

PORTUGUÊS 175..........................................

ÅËËÇÍÉÊÁ 192.............................................

FÖRSÄKRAN OM ÖVERENSSTÄMMELSE

Esab Welding Equipment AB, 695 81 Laxå, Sweden, försäkrar under eget ansvar att

svetsautomat A6 T F E1/TF E2/TGE1 från serienummer 725 är i överensstämmelse

med standard EN 60292 enligt villkoren i direktiv 89/392/EEG med tillägg.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

OVERENSSTEMMELSEERKLÆRING

Esab Welding Equipment AB, 695 81 Laxå, Sweden garanterer under eget ansvar,

at svejseautomat A6 TF E1/TFE2/TGE1 fra serienummer 725 er i overensstemmelse

med standard EN 60292 ifø lge betingelserne i direktiv 89/392/EEC med tillægg.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

FORSIKRING OM OVERENSSTEMMELSE

Esab Welding Equipment AB, 695 81 Laxå, Sweden, forsikrer på eget ansvar at

sveiseautomat A6 TFE1/TFE2/TGE1 med serienummer 725 er i samsvar med stan-

dard EN 60292 i overensstemmelse med bestemmelsene i direktiv 89/392/EØF med

tillegg.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

VAATIMUSTENMUKAISUUSVAKUUTUS

Esab Welding Equipment AB, 695 81 Laxå, Sweden, vakuuttaa omalla vastuullaan,

että hitsausautomaatti A6 TFE1/TFE2/TGE1 sarjanumerosta 725 täyttää standardin

EN 60292 vaatimukset direktiivin 89/392/EEC ja sen lisäyksen mukaisesti.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

DECLARATION OF CONFORMITY

Esab Welding Equipment AB, 695 81 Laxå, Sweden, gives its unreserved guarantee

that automatic welding machine A6 TFE1/TFE2/TGE1 from serial number 725 com-

plies with standard EN 60292, in accordance with the requirements of directive

89/392/EEA and addendum.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

KONFORMITÄTSERKLÄRUNG

Esab Welding Equipment AB, 695 81 Laxå Sweden, versichert hiermit auf eigene

Verantwortung, daß der Schweißautomat A6 TF E1/TFE2/TGE1 ab Serien--Nr 725

mit der norm EN 60292 gemäß den Bedingungen der Richtlinien 89/392/EWG mit

der Ergänzung in Übereinstimmung steht.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

CERTIFICAT DE CONFORMITÉ

Esab Welding Equipment AB, 695 81 Laxå Sweden, certifie sous sa propre respon -

sabilité que la appareil d e soudage automatique A6 TF E1/TF E2/TGE1 à par tir du

numéro de serié 725 répond aux normes de qualité EN 60292 conformément aux

directives 89/392/EEC avec annexe.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

OVEREENKOMSTIGHEIDSVERKLARING

Esab Welding Equipment AB, 695 81 Laxå Sweden, verklaart op eigen verantwoor-

delijkheid dat lasautomaat A6 TFE1/TFE2/TGE1 van serienum m er 725 overeenkomt

met norm EN 60292 volgens r ichtlijn 89/392/EEG van de Raad me t toevoeging.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

DECLARACIÓN DE CONFORMIDAD

Esab Welding Equipment AB, 695 81 Laxå, Sweden, declara, asumiendo toda res -

ponsabilidad, que la equipo par a soldadura automática A6 T FE1/TFE2/TGE1 desde

el número de serie 725 está fabricada de conformidad con la normativa EN 60292

según los requisitos de la directiva 89/392/EEC con el suplemento.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

DICHIARAZIONE DI CONFORMITA

Esab Welding Equipment AB, 695 81 Laxå Sweden, dichiara sotto la propria respon-

sabilità che la saldatrice automatica A6 TFE1/TFE2/TGE1 dal numero di serie 725 è

conforme alla norma EN 60292 ai sensi dei requisiti previsti dalla direttiva

89/392/CEE e successive integrazioni nella direttiva.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

DECLARAÇÃO DE CONFORMIDADE

Esab Welding Equipment AB, 695 81 Laxå Sweden, certifica, sob a sua própria res -

ponsabilidade que, a equipamento automático para soldadura A6 T FE1/TFE2/TGE1

desde número de série 725 está em conformidade com a norma EN 60292, segun-

do os requisitos constantes na directiva 89/392/EEC e com o suplemento.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

ÂÅÂÁÉÙÓÇ ÓØÌÖÙÍÉÁÓ

Ç E sab Welding Equipment AB, 695 81 Laxå Sweden, âåâáéþíåé ìå äéêÞ ôçò åõèýíç

oôé ç áõôüìáôò óõãêïëëçôÞò A6 TFE1/TFE2/TGE1 áðü ôïí áñéèìü óåéñÜò 725

âñßóêåôáé óå óõìöùíßá ìå ôï óôáíôáñô ÅÍ 60292 óýìöùíá ìå ôïõ üñïõò ôçò

ïäçãßáò 89/392/ÅÅC êáé ôçí ðñïóèÞêç.

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Paul Karlsson

Managing Director

Esab Welding Equipment AB

695 81 LAXÅ

SWEDEN Tel: + 46 584 81176 Fax: + 46 584 12336

Laxå 97--04--15

ENGLISH

TOCe

-- 7 3 --

1SAFETY 74...........................................................

2 INTRODUCTION 76...................................................

2.1 General 76..................................................................

2.2 Technical data 76............................................................

2.3 Welding method 77...........................................................

2.4 Horizontal Welding or Welding on an Inclined Plane 77............................

2.5 Equipment 78................................................................

3 INSTALLATION 80....................................................

3.1 General 80..................................................................

3.2 Connections 80..............................................................

4 OPERATION 82.......................................................

4.1 General 82..................................................................

4.2 Starting work 82..............................................................

4.3 Refilling with flux powder (submerged--arc welding) 87............................

4.4 Conversion of A6 TFE1 (Submerged--arc welding) to MIG/MAG welding 87..........

4.5 Conversion of A6 TFE1 / A6 SFE2 (Submerged--arc welding) to Twin--arc 87.........

5 MAINTENANCE 88....................................................

5.1 General 88..................................................................

5.2 Daily 88.....................................................................

5.3 Regularly 88.................................................................

6 TROUBLESHOOTING 89..............................................

6.1 General 89..................................................................

6.2 Possible faults 89............................................................

7 ORDERING OF SPARE PARTS 89......................................

WEAR COMPONENTS 211..............................................

SPARE PARTS LIST 215................................................

-- 7 4 --

ffa8safE

1SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety precautions

must meet the requirements that apply to this type of welding equipment. The following recommen-

dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

S its operation

S location of emergency stops

S its function

S relevant safety precautions

S welding

2. The operator must ensure that:

S no unauthorised person is stationed within the working area of the equipment when it is

started up.

S no--one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose

S be free from draughts

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.

S Work on high voltage equipment may only be carried out by a qualified electrician.

S Appropriate fire extinquishing equipment must be clearly marked and close at hand.

S Lubrication and maintenance must not be carried out on the equipment during operation.

Welding on an Inclined Plane -- In the T ravel Direction or Sideways

Mind the following:

S That the freewheel clutch of the gear shall be in locked position.

S That, if the operator leaves the machine, it shall be parked with blocks in front of the wheels, in

order to prevent the machine from moving unintentionally.

S Make sure that the automatic welding machine is not unstable before start.

S That the placement of the welding head and the wire reel influence the centre of gravity of the

machine.

Too high a centre of gravity means an unstable welding machine.

S That the consumption of wire and flux results in displacement of the weight distribution during the

welding.

-- 7 5 --

ffa8safE

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-

TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE

BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.

S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

S Insulate yourself from earth and the workpiece.

S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.

S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.

S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

-- 7 6 --

ffa8d1ea

2 INTRODUCTION

2.1 General

The A6 TFE1 automatic welding machine is mounted on a self--propelled trolley

and is designed for submer ged--arc welding of butt and fillet welds.

The A6 TFE2 automatic welding machine, with two welding heads, is mounted on

a self--propelled trolley and is designed for submerged--arc welding of butt welds.

The A6 TGE1 automatic welding machine is mounted on a self--propelled trolley

and is designed for MIG/MAG welding of butt and fillet welds.

All other uses are prohibited.

The automatic welding machines are used in conjunction with ESABÕs control box

A2--A6 Process Controller (PEH).

The supply voltage to the control box and to the welding machine m otors is provided

by ESAB’s welding power sources LAF and TAF.

The position of welding head can be set horizontally and vertically with the linear

slides. Angular movement is adjusted with the angular slide.

2.2 Technical data

A6 TFE1 A6 TFE2 A6 TGE1

6 Mastertrac

Submerged--arc MIG/MAG

Supply voltage 42 V AC 42 V AC 42 V AC

Rated load 100 % 1500 A DC/AC 1500 A DC/AC 600 A DC

Electrode dimensions:

solid single wire 3.0--6.0 mm 3.0--6.0 mm 1.0--2.4 mm

flux--cored wire 3.0--4.0 mm 3.0--4.0 mm 1.6--3.2 mm

twin wire 2x2.0--3.0 2x2.0--3.0mm -- --

Electrode feed rate, max. 4m/min 4m/min 16 m/min

Brake drum braking torque 1.5 Nm 1.5 Nm 1.5 Nm

Speed of travel 0.1--2.0 m/min 0.1--2.0 m/min 0.1--2.0 m/min

Electrode weight, max. 30 kg 2x15kg 30 kg

Flux hopper capacity

(Must not be filled with preheated flux)

10 l 10 l -- --

Weight (excluding electrode and flux) 110 kg 158 kg 100 kg

Continuous A weighted sound pressu-

68 dB 68 dB 83 dB

-- 7 7 --

ffa8d1ea

2.3 Welding method

Submerged--arc welding

For submerged--arc welding, an A6 Mastertrac of type A6 TF is used, which is

available in several different versions:

S Submerged--arc Light duty

Submerged--arc light duty, with a ∅ 20 mm connector, which permits a load of up

to 800 A (100%) or 1000 A (60%).

S Submerged--arc Heavy duty

Submerged--arc heavy duty, with a ∅ 35 mm connector, which permits a load of

up to 1500 A.

Both versions can be equipped with feed rollers for single or twin wire welding

(twin--arc). A special knurled feed roller is available for flux--cored wire, which

guarantees even wire feed without the risk of deformation due to high feed pressure.

For work in confined spaces, (smaller than 50 cm), a special welding head of type

A6 SFE1C is available, which can be installed on the Mastertrac as required.

Tandem welding (submerged--arc)

For tandem welding, a welding head of type A6 TFE2 is always used, which must be

connected to 2 welding power sources and 2 control boxes of type A2--A6 Process

Controller.

The tandem welding head includes 2 single welding heads ( A6 SF), each with its

own contact tip. Each contact tip has a maximum rated load of 1500 A.

MIG/MAG welding

For MIG/MAG welding, an A6 Mastertrac A6 TGE1 is used, which has a maximum

rated load of 600 A. The welding head is water cooled, with the cooling water

supplied by hoses from connections intended for the purpose.

2.4 Horizontal Welding or Welding on an Inclined Plane

The automatic welding machines are designed for horizontal welding in the first

place.

Read the section Welding on an Inclined Plane - In the Travel Direction or

Sideways, on page 74.

-- 7 8 --

ffa8d1ea

2.5 Equipment

Included in a complete welding head are a feed motor (A6 VEC) to feed in the wire

and contact equipment which supplies current to the wire and provides a good

contact.

Contact equipment is available in several different versions.

S A6 TF is used for submerged--arc welding.

S A6 TG is used for MIG/MAG welding.

Main components of the A6 TFE1 and A6 TFE2

1. Straightener.

2. Contact equipment which

consists of a contact tip,

connector and flux tube.

3. Angular slide

4. Slide (motor or handdriven)

5. Motor and gearbox (A6 VEC)

6. Wire drum

7. Flux hopper (may be

fitted with a cyclone)

8. --

9. Tr olley

10. Column

11. Disengagement lever

Main components of the A6 TGE1

1. Straightener.

2. Contact equipment which

consists of a connector, gas

nozzle and water hoses.

3. Angular slide.

4. Slide (motor or hand driven).

5. Motor and gearbox (A6 VEC).

6. Wire drum.

7. Fine wire straightener.

8. Wire guide.

9. Tr olley.

10. Column.

11. Disengagement lever.

-- 7 9 --

ffa8d1ea

Example of the A6 SFE1C, which can be mounted on an A6 Mastertrac

1. Straightener.

2. Contact equipment, which consists of a contact tip, connector and flux tube.

3. Slide (motor driven).

4. Motor and gearbox (A6 VEC).

5. Flux hopper (1 l).

For connection instructions for submerged--arc and MIG/MAG welding, see page 80.

-- 8 0 --

ffa8i1ea

3 INSTALLATION

3.1 General

The installatio n must be execu ted by a p rofessional.

WARNING

Rotating parts can cause injury, take great care.

3.2 Connections

3.2.1 General

S Connection of the control box A2--A6 Process Controller ( PEH) to the automatic

welding machine is carried out prior to delivery.

For further information, see instruction manual for the A2--A6 Process Controller

(PEH).

S Connect the A6 Mastertrac in accordance with the following diagrams.

3.2.2 Submerged--Arc Welding (SAW)

S Connect the control cable (7) between the welding power source (8) and the

control box PEH (2).

S Connect the return cable (11) between the welding power source (8) and the

work piece (9).

S Connect the welding cable (10) between the welding power source (8) and the

automatic welding machine (1).

S Connect the measuring cable (12) between the welding power source (8) and

the work piece (9).

-- 8 1 --

ffa8i1ea

3.2.3 Gas Metal Arc Welding (MIG/MAG)

S Connect the control cable (7) between the welding power source (8) and the

control box A2--A6 Process Controller (PEH) ( 2).

S Connect the return cable (11) between the welding power source (8) and the

work piece (9).

S Connect the welding cable (10) between the welding power source (8) and the

automatic welding machine (1).

S Connect the gas pipe (5) between the reduction valve (6) and the gas valve o n

the automatic welding machine (13).

S Connect the hoses for cooling water (3) between the cooling unit (4) and the

automatic welding machine (1).

S Connect the measuring cable (12) between the welding power source (8) and

the work piece (9).

-- 8 2 --

ffa8o1ea

4 OPERATION

4.1 General

General safety regulations for the handling of the equipment can be found on

page 74. Read through before you start using the equipment!

S Select wire type and flux powder or shielding gas so that the weld m aterial is as

close as possible to the analysis o f the base metal. Select wire size and welding

data in accordance with the values recommended by the welding materials

supplier.

S Thorough preparation of the weld surfaces is necessary to achieve a good weld.

NOTE! The width of the weld joint gap must be uniform.

S To minimise the risk of heat crack formation, the width of the weld must be

greater than the penetration depth.

S Always carry out a test weld with the same joint type and sheet thickness as the

production work piece.

S For control and adjustment of the automatic welding machine and welding power

supply, see the instruction manual for the A2--A6 Process Controller (PEH).

S The trolley can be moved manually after disengaging the disengagement lever,

see the diagram on page 78.

S When changing consumables, see table on page 211.

4.2 Starting work

Loading the welding wire

S Remove the wire drum (1) from the brake hub (2)

and take off the side plate (3).

S Locate the wire reel on the wire drum (1).

S Cut off the binding wires from around the

wire reel.

S Replace the side plate ( 3).

S Replace the wire drum (1) on the brake hub (2).

Check that the carrier (4) is in the correct position.

NOTE! The maximum angle for the wire bobbin is 25¡.

At extr eme angles, wear will occur o n the brake hub locking

mechanism and the wire bobbin will slide off the brake hub.

WARNING

To prevent the reel sliding off the hub:

Lock the reel in place b y turning the r ed knob as shown

on the warning label attached next to the hub.

-- 8 3 --

ffa8o1ea

SAW MIG/MAG

S Check that the feed roller (1) and contact jaw or contact tip (3) are of the correct

dimension for the selected wire size.

S Pull the end of the wire through the straightener (2). For a wire diameter greater

than 2 mm; straighten out 0.5 m of wire and feed it by hand down through the

straightener.

S Locate the end of the wire in the feed roller (1) groove.

S Set the wire tension on the feed roller with the knob (7). Note! Do not tension

more than is required to achieve an even feed.

S The pressure screw (8) must not be dismantled. (Applies to Submerged--arc

Heavy duty).

S Feed the wire forward 30 mm by pressing on the control box

A2--A6 Process Controller.

S Direct the wire by adjusting the knob (6).

For fine wire, the special fine wire straightener (4) is used for both single and

twin wire.

Ensure that the straightener is correctly adjusted so that the wire emerges

straight out through the contact jaws or contact tip.

Always use a guide tube (5) to ensure even feeding of fine wire (1.6 -- 2.5 mm).

For MIG/MAG welding with wire sizes < 1.6 mm, use a guide spiral, which is

inserted in the guide tube (5).

-- 8 4 --

ffa8o1ea

Changing the feed roller

S Single wire

S Release the knobs (3) and (4).

S Release the hand wheel (2).

S Change the feed roller (1). They are marked with their

respective wire sizes.

S Twin wire (Twin--arc)

S Change the feed roller (1) with twin grooves in the same way as

for single wire.

S NOTE! Th e pressure roller (5) must also be changed. A special curved

pressure roller for twin wire replaces the standard pressure roller for single

wire.

S Assemble the pressure roller with special stub shaft

(order no. 146 253--001).

S Flux--cored wire (for knurled rollers)

S Change the feed roller (1) and pressure roller (5) as a pair for the wire size

to be used.

NOTE! A special stub shaft is required for the pressure roller

(order no. 2129 011--01).

S Tighten the pressure screw (4) with moderate pressure to ensure that the

flux--cored wire does not deform.

Contact equipment for submerged--arc welding

S For single wire 3.0 -- 4.0 mm. Light duty (D20)

Use the straightener (3), connector (1) D20 with contact tip

(2) (M12 thread).

S Tighten the contact tip (2) with a key in order to ensure

that a good contact is achieved.

S For single wire 1.6 -- 2.5 mm Submerged--arc.

Light duty (D20)

Use the straightener (3), connector (1) D20 with contact

tip ( 2) (M12 thread) and separate fine wire straightener (4)

with guide tube (6).

S Assemble the clamp (7) with guide tube (6) in the M12

hole on the straightener (3). The guide tube (6) should

bottom on the contact tip (2).

S If necessary, cut the guide tube (6) to length so that the

feed roller ( 5) runs freely.

S Assemble the fine wire straightener (4) on the upper

side of the clamp for the straightener (3).

-- 8 5 --

ffa8o1ea

S For single wire 3.0 -- 6.0 mm. Heavy duty (D35)

Use the straightener (3), connector (1) D35 with contact

jaws (2).

S Assemble one contact jaw with the M5 bolts provided, in

the fixed contact tip (a).

S Assemble the other contact jaw in the free half of the

two--piece connector ( b) under the bolt (8) and tighten

down hard to ensure that a good contact is achieved

between the contact jaws and the wire.

S For flux--cored wire 1.6 mm -- 4.0 mm (D20 and D35) (Accessories)

If contact jaws ( D35) are used, the contact jaws must not be tightened down to

hard in order to ensure that the flux--cored wire is not distorted. Ensure that good

contact is achieved with the wire.

S Adjustment of the wire for tandem welding

S The distance between the first and second wires must not be so great that

the slag has tim e to solidify between the wires.

S Ensure that good flux coverage is achieved between the first and second

wires.

S Fortwinwires2x2.0--3.0Heavy Twin (D35) (Accessories)

Use the straightener (3), connector (1) D35 with contact

jaws (2).

S Assemble the first contact jaw with the M5 bolts

supplied, in the fixed connector ( a).

S Assemble the other contact jaw in the free half of the

two--piece connector ( b) under the bolt (8) and tighten

down hard to ensure that a good contact is achieved

between the contact jaws and the wire.

-- 8 6 --

ffa8o1ea

S Fortwinwires2x1.2--2.0mm,LightTwin(D35)(Accessories)

Use the straightener (3), connector (1) D35 with twin adapter

(9) and 2 contact tips (2) (M6 threads) and separate fine wire

straightener (4) with two guide tubes (6). F or twin wires < 1.6

mm, a guide spiral, inserted into each guide tube, is used.

S Assemble the twin adapter (9) for M6 contact tips (2) with

the M5 bolts in the fixed half of the two--piece connector

(1).

S Assemble the clamp (7) with guide tube (6) in the M12

hole on the standard straightener (3). The guide tube

should bottom on the twin adapter (9) for the contact tip

(2).

S Tighten the contact tip (2) with a key to ensure that a good

contact is achieved.

S If necessary, cut the guide tube (6) to length so that the

feed roller ( 5) runs freely.

S Adjustment of the wires for Twin--arc welding:

S Position the wires in the joint so as to achieve optimal weld quality by

rotating the connector. The two wires can be rotated so that they are

positioned one after the other along the line of the joint, or in any position

up to 90¡ across the joint, i.e. one wire on each side of the joint.

Contact equip ment for MIG/MAG welding.

S For single wire 1.6 -- 2.5 mm (D35)

Use the straightener (3), connector (1) D35 with contact

tip ( 2) (M10 thread).

S Tighten the contact tip (2) with a key to ensure that a

good contact is achieved.

S Assemble the clamp (7) with guide tube (6) in the M12

hole on the standard straightener (3). The guide tube (6)

should bottom on the contact tip (2).

S If necessary, cut the guide tube (6) to length so that the

feed roller ( 5) runs freely.

-- 8 7 --

ffa8o1ea

S For single wire < 1.6 mm (D35)

Use the straightener (3), connector (1) D35 with contact tip

(2) (M12 thread), fine wire straightener (4) with guide tube

(6) and guide spiral, which is inserted in the guide tube (6).

S Assemble the clamp (7) with guide tube (6) in the M12

hole on the standard straightener (3). The guide tube (6)

should bottom on the contact tip (2).

S If necessary, cut the guide tube (6) to length so that the

feed roller ( 5) runs freely.

S Assemble the fine wire straightener (4) on the upper side

of the clamp for the straightener (3).

S Connect the cooling water and gas (MIG/MAG welding).

4.3 Refilling with flux powder (submerged--arc welding)

S Close the flux valve on the flux hopper.

S Remove the cyclone on the flux r ecovery unit, if fitted.

S Fill with flux powder. NOTE! T he flux powder must be dry. Where possible

avoid using agglomerating flux powder outdoors and in damp environments.

S Position the flux tube so that it does not become kinked.

S Adjust the height of the flux nozzle above the weld so that the correct

amount of flux is delivered.

Flux coverage should be sufficient so that penetration of the arc does not

occur.

4.4 Conversion of A6 TFE1 (Submerged--arc welding) to MIG/MAG

welding

Assemble in accordance with the instructions accompanying the conversion

kit.

4.5 Conversion of A6 TFE1 / A6 SFE2 (Submerged--arc welding) to

Twin--arc

Assemble in accordance with the instructions accompanying the conversion

kit.

-- 8 8 --

ffa8u1ea

5 MAINTENANCE

5.1 General

NB! Before doing any kind of maintenance work, make sure the mains is

disconnected.

For the maintenance of the A2--A6 Process Controller (PEH), see the instruction

manual.

5.2 Daily

S Clean flux and dirt off moving parts of the welding machine.

S Check that the contact tip and all electrical cables are connected.

S Check that all bolted joints are tight and that guides and drive rollers are not

worn or damaged.

S Check the brake hub braking torque. It should not be so low, that the wire reel

continues to rotate when wire feed is stopped and it should not be so great that

the feed rollers slip. As a guide, the braking torque for a 30 kg wire reel should

be 1,5 Nm.

Adjusting the braking torque:

S Turn the red handle to the locked

position.

S Insert a screwdriver into the

springs in the hub.

Turn the springs clockwise to

reduce the braking torque

Turn the springs anticlockwise to increase the braking torque.

NB: Turn both springs through the same amount.

5.3 Regularly

S Check the wire feed motor brushes

once every three months.

Replace when they are worn

downto6mm.

S Eximine the slides and lubricate if

they bind.

S Inspect the wire guides, drive

rollers and contact tip on the wire

feed unit. Replace any worn or damaged

components, (see spare parts list on page 215).

S If the carriage travel becomes

jerky, check that hte chain is correctly tensioned. Tension the chain if necessary.

S To tension the chain undo the nut (*1) and turn the cam, then tighten the nut.

La pagina sta caricando ...

ESAB A6 TFE1 / TFE2 / TGE1 Manuale utente

Marca: ESAB

Modello: A6 TFE1 / TFE2 / TGE1

Categoria: Sistema di saldatura

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ESAB A6 TFE1 / TFE2 / TGE1 User manual

ESAB A6 TFE1 / TFE2 / TGE1 Manuale utente

ESAB A6 TFE1 / TFE2 / TGE1 Manuale utente

in altre lingue

Documenti correlati