Spektrum Focal DVR FPV Headset Manuale utente

1

SPMVR2520 Instruction Manual

SPMVR2520 Bedienungsanleitung

SPMVR2520 Manuel d’utilisation

SPMVR2520 Manuale di Istruzioni

2

NOTICE

All instructions, warranties and other collateral documents are subject to change

at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit

horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various

levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of

property damage, collateral damage, and serious injury OR create a high probability

of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of

physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical

property damage AND a little or no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the

features of the product before operating. Failure to operate the product

correctly can result in damage to the product, personal property and cause

serious injury.

This is a sophisticated hobby product. It must be operated with caution and common

sense and requires some basic mechanical ability. Failure to operate this Product in a

safe and responsible manner could result in injury or damage to the product or other

property. This product is not intended for use by children without direct adult supervi-

sion. Do not attempt disassembly, use with incompatible components or augment

product in any way without the approval of Horizon Hobby, LLC. This manual contains

instructions for safety, operation and maintenance. It is essential to read and follow all

the instructions and warnings in the manual, prior to assembly, setup or use, in order

to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS

Thank you for purchasing a genuine Spektrum product. Always purchase from a

Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum

product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not

limited to, compatibility and performance of counterfeit products or products claiming

compatibility with DSM or Spektrum technology.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-

controlled vehicles and aircraft. Horizon Hobby disclaims all liability outside of the intended

purpose and will not provide warranty service related thereto.

WARRANTY REGISTRATION

Visit www.spektrumrc.com/registration today to register your product.

3

Box Contents

Headset Carry Case

Headset

Cleaning Cloth

Product Speciﬁ cations

IMPORTANT: Consult local laws and ordinances before operating FPV (ﬁ rst person

view) equipment. In some areas, FPV operation may be limited or prohibited. You are

responsible for operating this product in a legal and responsible manner.

Focal® FPV Wireless Headset (SPMVR2520)

Field of View: 32 deg diagonal

Aspect Ratio: 4:3 or 16:9 selectable

IPD distance: 59 to 69 mm (adjustable)

Input power: 7–13V (2S–3S Li-Po)

Battery: 7.4V 1800mAh Li-Po battery with USB charger

Video Receiver: 5.8GHz (32 channels available)

Weight: 307 g

5.8GHz Antenna

Faceplate Foam and

Hook and Loop Material

7.4V 1800mAh

Li-Po Battery with USB charger

Needed to Complete

• Micro USB cable is required for charging (not included)

• Micro SD card is required for DVR recording (not included)

4

• NEVER LEAVE CHARGING BATTERIES

UNATTENDED

• NEVER CHARGE BATTERIES

OVERNIGHT

• By handling, charging or using the

included Li-Po battery, you assume all risks

associated with lithium batteries.

• If at any time the battery begins to balloon

or swell, discontinue use immediately. If

charging or discharging, discontinue and

disconnect. Continuing to use, charge or

discharge a battery that is ballooning or

swelling can result in ﬁ re.

• Always store the battery at room

temperature in a dry area for best results.

• Always transport or temporarily store the

battery in a temperature range of 40–120º

F (5–49° C). Do not store the battery or

model in a car or direct sunlight. If stored

in a hot car, the battery can be damaged or

even catch ﬁ re.

• Always charge batteries away from

ﬂ ammable materials.

• Always inspect the battery before charging.

• Always disconnect the battery after charging,

and let the charger cool between charges.

• Always constantly monitor the temperature

of the battery pack while charging.

• ONLY USE A CHARGER SPECIFICALLY

DESIGNED TO CHARGE LI-PO BATTERIES.

Failure to charge the battery with a

compatible charger may cause a ﬁ re

resulting in personal injury and/or property

damage.

• Never discharge Li-Po cells to below 3V

under load.

• Never cover warning labels with hook and

loop strips.

• Never charge batteries outside

recommended levels.

• Never charge damaged batteries.

• Never attempt to dismantle or alter the

charger.

• Never allow minors to charge battery

packs.

• Never charge batteries in extremely hot

or cold places (recommended between

40–120° F [5–49° C]) or place in direct

sunlight.

Charger Warnings

CAUTION: All instructions and warnings must be followed exactly. Mishandling

of Li-Po batteries can result in a ﬁ re, personal injury and/or property damage.

Cooling Fan

Connector

Charging the Headset Battery Pack

1. Connect a Micro USB cable

to your power supply and the

battery. A 2-amp power supply is

recommended, which will result

in approximately 1 hour charge

time. A 500mA USB supply will

take approximately 4 hours

to complete a full charge.

2. The red LED next to the USB

port will illuminate when the

battery is charging, and it will turn off when the battery is fully charged.

NOTICE: The cooling fan connector is not a battery balance lead. Do not connect the cooling

fan connector to a balance port on a charger.

5

Focal FPV Wireless Headset Functions

LED Power Meter

Test Button

7.4V 1800mAh Li-Po battery

with Power Meter

Antenna Connection

Fan

Cooling Fan Button

Top

Fan Power Port

Power In

AV In/Out

Right Side

Data Port

(wired head tracking)

VRX Power Switch

Video Receiver

Compartment

IPD Adjustment

Headphone Jack

Bottom

Head Tracker Reset

5-Way Video

Display Control

Channel Select

5-Way DVR Control

Volume

Mini HDMI

®

Video

Input

Battery Connection

The included 7.4V 1800mAh Li-Po battery has

an integrated LED power meter. Press the button

on the side of the battery and a series of 4 LEDs

will illuminate to indicate charge status. When

only one LED is illuminated, charge the battery

before use.

1. Connect the battery to the headset as shown.

2. Press the cooling fan button to turn the fan

on. The fan will run for approximately 10

minutes and then powers off automatically

3. Use of the cooling fan is optional, but is

recommended to prevent the headset from

fogging during use.

6

Controls

Mini HDMI

®

Input

HIGH-DEFINITION MULTIMEDIA INTERFACE

®

Brightness and contrast control: Pressing the 5-way video display control left

increases the display contrast, pressing right will decrease contrast. Pressing forward

will increase brightness and pressing back will decrease brightness.

Display mode selection: Press down vertically on the 5-way video display control to

sequence through the following modes: Analog 16:9, Analog 4:3, Analog 3D, HDMI 2D,

and HDMI 3D.

Low battery warning: The headset will emit increasingly frequent audio warning

beeps if the input voltage drops below 6.8V. If the low voltage warning begins while

ﬂ ying, land immediately. If the voltage warning is ignored, the headset will eventually

shut off and stop displaying the video signal.

Volume control: Each press of the button steps the volume up or down.

AV Output/Input: The same connector is used for either video input or output. It will

operate as an output if the cable is connected to an external monitor. To use as an

input, connect the cable to an analog video source. Ensure the video receiver module is

powered off and the DVR is not in playback mode.

IPD Adjustment: Adjust the sliders for optimal alignment.

The Mini HDMI port can be

connected to HDMI devices

by using an HDMI cable with

a Mini HDMI connector or

Mini HDMI adaptor.

1. Connect an HDMI cable

to the HDMI device and

the headset.

2. Power on the video source.

3. Power on the headset.

Disconnect the battery when

switching between devices to

clear the settings.

The video receiver module needs to be powered off or removed when operating in

HDMI mode for proper operation.

Tip: Most HDMI connectivity issues are due to either incorrect display settings at the

video source, or a faulty HDMI cable. Before assuming the HDMI feature is defective, try

with alternative HDMI sources and alternative cables. HDMI cables may fracture over

time at connector ﬂ ex points.

7

Faceplate Foam Installation

Diopter Inserts (Optional)

1. The Focal

®

DVR headset includes two foam options you can try for optimal ﬁ t.

Experiment with these options and select your preference before installing the

hook and loop material. It is difﬁ cult to remove the foam from the hook and loop

material without damage.

2. Start applying the adhesive backed hook and loop material at the center and work

your way outward to ensure the material lays down properly on the faceplate.

3. Apply the foam to the hook and loop material and press it into place.

For users who require

prescription glasses, Fat

Shark offers a set of inserts

which include -2,-4, and -6

diopters, (FSV1601).

For specialized diopters, a

web search for “Fat Shark

custom diopter” will return

results leading to aftermarket

prescription inserts.

8

F7

5860

Video Receiver Module

Selecting Band

1. Press and hold the receiver display button for a moment to enter the analyzer mode

and to change bands. The video receiver display will show a frequency analyzer and

sweep through all the channels on the band, showing each channel’s signal strength. It

will continue to cycle through the frequencies until you press the button again.

2. A short press will enable you to change to the next band and then sweep through

the channels on that band to show signal strength.

3. Select the current band by pressing and holding the receiver display button for a

moment. Use the Headset channel control buttons on the top of the headset to

change to a speciﬁ c channel within the selected band.

Selecting Channel

1. Press and release the receiver display button to enter channel auto-select. The

receiver will sweep the selected band and select the strongest channel.

2. The channel selection buttons on top of the headset enable you to take manual

control of channel selection at any time. The headset emits an audio beep upon

changing the channel. A long beep sounds at the high and low channel limits and

no change will take place.

3. The headset will remain on the last channel in use after a power cycle.

Receiver Power Switch: The receiver

module power is independently

controlled from the small switch on the

bottom of the headset. If a module is

inserted, but the desired video source

is via the AV cable or HDMI cable, the

receiver module must be turned off to

avoid image conﬂ ict.

Receiver

Display

Button

Band

Channel

Frequency

Receiver Module Display

RSSI Indicator

Receiver Display Button: A small button next to the display on the receiver controls

the frequency analyzer, band selection and channel auto-select.

9

BAND CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

F Fat Shark 5740 5760 5780 5800 5820 5840 5860 5880

R RaceBand 5658 5695 5732 5769 5806 5843 5880 5917

E Band E 5705 5685 5665 5645 5885 5905 5925 5945

A Band A 5865 5845 5825 5805 5785 5765 5745 5725

Video Receiver Module

Antenna Selection

The included linear antenna is an excellent selection for aircraft with a linear antenna,

such as the Inductrix

®

FPV quadcopter. If your aircraft has a circularly polarized (CP)

antenna, we recommend changing the antenna on your headset to a SPMVX5802

(right hand), or SPMVX5812 (left hand). For a premium antenna option, consider the

SPMVX5851 (right hand) or SPMVX5861 (left hand). Always use the same rotation

direction (both right or both left hand) on the video transmitter and receiver when using

CP antennas.

Antennas with a standard SMA connector are required. Antennas with an RP-SMA

connector are not compatible without an adaptor, which is not recommended due to

associated RF losses.

Alternative Video Receiver Modules

The included video receiver is modular and may be

replaced with other modules. Fat Shark offers several

video receiver modules to suit your needs, and after-

market modules are also available. Operation is only

recommended for genuine Fat Shark receiver modules.

Module Replacement

1. Remove the antenna.

2. Pry off the video receiver module door.

3. Gently grasp the video receiver module and pull

straight out to remove.

4. Insert the replacement module, being sure to align the pins.

5. Press the door back into location until it snaps into place.

6. Use an appropriate antenna for your selected video frequency.

Some aftermarket module systems require the user to open the headset for installation.

Separating the top and bottom halves of the headset to install a wire harness for a

receiver installation will void the headset warranty.

Available Frequencies

10

Turning On The DVR

A red LED between the displays serves

as an indicator for DVR functions. After

powering on the headset, wait for the

red LED to cycle on and then off before

attempting to power on the DVR. Ensure

the SD card is inserted and then power

on the DVR by pressing and holding the

5-way DVR control button for 1 full second. The red LED should now show solid.

Recording

The DVR is only capable of recording analog video; it is not capable of recording HDMI

input.

Press and release the 5-way DVR control button to start recording. The headset will emit

a beep and the red LED will slowly ﬂ ash when the DVR is recording.

Press and release again to stop the recording. The headset will emit 2 beeps and the

red LED turns solid. Always stop recording before powering off headset. The headset

has a feature to stop recording if power is removed, but it is best to stop the recording

manually before powering off to ensure your recorded video doesn’t get corrupted.

DVR Operation

Micro SD Card

1. Do not place alternative ﬁ les you

want to keep on the SD card being

used to record video. The DVR may

not recognize the ﬁ le space and

may write over your ﬁ les. Use a

dedicated SD card.

2. The SD card should be formatted

before use to ensure stable

recording.

3. Insert the micro SD card (not included) with the labeling facing up and the

contacts facing down.

4. Press the SD card gently into place until it clicks into position and stays inserted.

5. Remove the SD card by pressing in with a ﬁ nger tip until the card clicks and releases.

Tip Entering the DVR menu and Playback requires turning off or removing the video

receiver module and removing any other video input sources to prevent conﬂ ict with the

DVR menu and playback.

11

DVR Operation

Menu Navigation

1. After turning on the DVR, and while the DVR

is not recording (indicated by a solid red

LED), press and hold the 5-way DVR control

button for 1 second to enter the menu.

2. Press forward or backward on the 5-way

DVR control button to navigate the menu.

The selection is highlighted in orange.

3. Press right on the 5-way DVR control button

to make a selection. Pressing left from the main menu exits the menu.

Playback Controls

When Playback is selected, the video will display a preview shot with the ﬁ le number.

1. Press up or down to change ﬁ le selection.

2. Press right to play the video.

During Playback

1. Pressing up will speed up the video and display the speed on screen.

2. Pressing down will slow down playback and enable you to reverse playback as

well.

3. Pressing the button to the right will pause or play the video.

4. Pressing the button to the left will exit back to the main menu.

Formatting the Memory Card

From the main menu and with Format selected, press right on the 5-way DVR control

button to begin the formatting process for the memory card. After one press, the

display will ask if you want to execute the format. Press right to again to format the

memory card. Press left to cancel the formatting.

Recording Options

The main menu displays the current record in the right column next to record. With

Record selection, press right on the DVR button to open a sub menu with the following

options.

1. Default: Requires turning on the DVR and manually pressing record.

2. Auto start: DVR powers on and starts to record automatically on power up. Stops

recording if the card is full.

3. Auto start continuous: DVR powers on and starts to record automatically on power

up. Overwrites content on card and continues to record if the card is full.

12

Head Tracking

The Trainer FPV function found in Spektrum AirWare™ radios with wireless trainer

enables you to control your FPV camera with head-tracking in either wireless or

wired mode. All Spektrum computer radios equipped with wireless buddy box can be

upgraded to include this feature by registering your radio at SpektrumRC.com and

downloading the newest updates.

Wireless Head Tracker Conﬁ guration in Spektrum Airware

1. Select Wireless Trainer from the Trainer

menu, in the system menu.

2. Change the trainer mode from Inhibit to FPV.

3. Select the switch you wish to use for

the head tracker, then select NEXT.

4. Select the Output Channel where the

head tracker servo is connected.

5. Change Mode: Master to Mode: Slave.

6. Select Input Channel.

(see default channel assignments)

7. Select bind and press the scroll wheel to

put the Transmitter into bind mode.

8. Power on the headset and it will attempt

to bind to the wireless buddy box function

in the transmitter. The Transmitter should

report DSMX 11ms after a successful bind.

9. After binding, the Transmitter will return to the

main menu. To test the head tracker movement,

use the channel monitor. Move the assigned

head tracker switch to the On position, and

press the Head tracking button on the headset

to initialize the head tracker, then rotate the

headset. The

assigned head tracker channels should follow headset movements.

10. Conventional reverse and travel functions do not work for head tracking output

channels, so there are special features in the FPV trainer menu to accommodate

this. Adjust the Scale value to change the amount of travel. If the camera moves

in the wrong direction, change the Direction option from Normal to Reverse.

11. Every time the headset is powered up it will attempt to bind to

a wireless trainer equipped Spektrum transmitter. If it does not

bind during the ﬁ rst several seconds, the headset will attempt to

connect to the previous wireless trainer it was bound to.

13

Head Tracking

IMPORTANT: All wireless buddy box equipped Spektrum transmitters can function with

up to 20 channel input for this functionality in the FPV trainer mode.

TIP: The receiver power switch must be in the On position for the wireless trainer

to operate. If you wish you use an external video source and wireless head tracking,

remove the video receiver module and leave the power switch in the On position.

Default Channel Assignments:

• CH17 Frequency • CH18 Pan • CH19 Tilt • CH20 Roll

Head Tracker Center Position

The Head Tracker senses a neutral

position for pan when you initialize the

head tracker by pushing the HT button.

If you need to reset the center position:

1. Move the headset to the desired

camera center position.

2. Quickly press the Head

Tracker (HT) button to save

the new center position.

Tip:

Resetting the center position only affects pan. Tilt and roll functions are

always set to re-center at a level position and cannot be adjusted. Adjust servo

center positions at the servo horn to affect the neutral point of tilt and roll axis.

IMPORTANT:

Head tracker sensors detect any movement, because of

this the operator needs to stay in-position during operation. The head

tracker will not work properly if you are in a moving vehicle.

NOTICE: As a default, the ﬁ rst four channels (Thr, Ail, Ele, and Rud) are set to

Master. Do not select Slave on ﬂ ight controls or ﬂ ight modes, or those channels will

be ﬁ xed at a neutral position when the wireless link is active. This could result in a

loss of control or an unexpected operation of throttle. For aircraft, always conﬁ rm

operation before ﬂ ight with propellers or rotor blades removed before testing a

new conﬁ guration. For surface vehicles, it is recommended to unplug the motor or

temporarily disengage the drive train to verify operation.

You may assign incoming head-tracker channels to any available output channel in the

transmitter.

14

Wired Head Tracking

Most radio systems will connect to the optional cables for wired head tracking, but

many lack the programming functions to have both head tracking and ﬂ ight controls

operating at the same time. Consult the radio system manual for information on trainer

or buddy box features.

Available option parts (not included) include FSV2113 for Spektrum/JR and FSV2112

for Futaba to connect the data port on the headset and the trainer port on common RC

control transmitters.

Wired Head Tracker Settings

NOTICE: For proper wireless head tracker operation, beep code menu points 1, 2, 3,

9 and 10 must be in a default state. If you are having problems with wireless head

tracking, restore the head tracker settings to factory defaults with menu point 11.

Head Tracking

Beep Code Menu Navigation

1. 1 short beep: Pan/Tilt/Roll on ch 5/6/7

2. 2 short beeps: Pan/Tilt/Roll on ch 6/7/8

3. 3 short beeps: Pan/Tilt only (no roll) output channel options

Long beep upon entering sub menu

1 short beep: Pan/Tilt only on ch 5/6

2 short beeps: Pan/Tilt only on ch 5/7

3 short beeps: Pan/Tilt only on ch 5/8

4 short beeps: Pan/Tilt only on ch 6/7

5 short beeps: Pan/Tilt only on ch 6/8

6 short beeps: Pan/Tilt only on ch 7/8

No selection: exit menu

One advantage of using Spektrum AirWare radios for head tracking is there is little

to no reason to use the head tracking menu in the headset. For most adjustments it

is easier to make the changes in the radio system. This also enables one common

conﬁ guration in the headset and individual model conﬁ guration needs are handled on

the radio side.

To enter the head tracking menu, hold the Head Tracking button (HT) while inserting the

battery connector and immediately release the button after barrel insertion. The head-

set emits a series of short and long beeps to indicate menu options. Follow along and

read the navigation menu as you listen to the beeps. Press the HT button immediately

after the tone indicates the menu point you wish to select.

Menu points with multiple options have a sub menu. Upon pressing the HT button at these

menu points, the headset will emit a long beep to indicate a sub menu has been selected

and then proceed with a short beep to indicate the ﬁ rst option in the sub menu.

15

4. 4 short beeps: servo reversing

Long beep upon entering sub menu

1 short beep: reverse pan direction

2 short beeps: reverse tilt direction

3 short beeps: reverse roll direction

No selection: exit menu

5. 1 long beep: adjust servo center point: press to gain manual control of the camera

with the headset. Adjust camera to desired center position and press button to set

new camera center. Servos must be mechanically centered before adjusting the

center point, or the servo travel may be limited.

6. 1 short beep: pan ratio options

Long beep upon entering sub menu

1 short beep: ratio = 1:1

2 short beeps: ratio = 1:1.5

No selection: exit menu

7. 2 short beeps: tilt ratio options

Long beep upon entering sub menu

1 short beep: ratio = 1:1

2 short beeps: ratio = 1:1.5

No selection: exit menu

8. 3 short beeps: auto pause on/off (if head tracker movement exceeds 90˚, this

selection puts Head Tracker in pause mode)

9. 4 short beeps: extended servo travel options *

Long beep upon entering sub menu

1 short beep: standard range = 1.04 ms – 2.0ms (center = 1.52ms +/- 0.48)

2 short beeps: extended range = 0.8ms – 2.24ms (center = 1.52ms +/- 0.72)

No selection: exit menu

10. 5 short beeps: cycle time*

Long beep upon entering sub menu

1 short beep: standard cycle (8CH PPM, 20ms)

2 short beeps: rapid cycle (3CH PPM, 8ms)

No selection: exit menu

11. 6 short beeps: restore factory defaults

12. 2 long beeps: no selection made, automatically exits menu

* May cause erratic behavior with some radio systems. Recommended for advanced

users only. Test thoroughly before use.

Head Tracking, continued

16

NOTICE: Do not leave the headset video displays exposed to direct sunlight.

Sunlight is magniﬁ ed by the lens and will burn holes in the LCD color ﬁ lter

(appears as white open areas). LCD damage is not covered under warranty.

Keep the headset in its protective case

when not in use.

1. Attach the antenna to the headset.

2. Insert the battery into the slot on

the right of the headband. Insert the

barrel connector on the fully charged

battery into the socket on the side

of the headset. The headset powers on when connected and must be

unplugged to turn it off.

3. Most FPV events will assign frequencies, consult event organizers for fre-

quency information before powering on any video transmitter at an event.

4. If there are assigned frequencies, set your headset to the designated

frequency to conﬁ rm the channel is open. Clean channels will have a

consistent static background. Channels with interference will display hori-

zontal static lines. Do not power on a video transmitter if there is another

video signal on the designated frequency.

5. When operating alone, verify activity on the band ﬁ rst with the frequency

scanner feature on the video receiver.

6. After choosing a clean channel in the headset, select the same channel on

the video transmitter

and conﬁ rm you get a solid video reception.

7. Test all head tracking features and conﬁ rm all control surfaces on the

aircraft respond as desired.

8. Perform a range test before ﬂ ying.

9. Fly in open areas, away from people, trees, cars, and buildings. The range

of the system can be impacted by any obstructions blocking your signal. It

is normal to see break up in the video when going behind trees etc.

10. When the headset battery gets low, the headset will emit a beeping that

gets progressively more rapid as the battery voltage drops. Always land and

recharge the headset battery when you begin to hear the headset beep.

Using the Focal DVR FPV Wireless Headset

17

Spektrum FPV Troubleshooting

Problem Possible Cause Solution

No image, display is

completely dark

No power supplied to the

video transmitter or headset

Check the power

connections

Make sure the battery is fully

charged

No image, display is

glowing dark gray

Video receiver module power

switch is in the off position.

Ensure the video receiver

power switch is powered on

Static on all channels

Video transmitter power

is off

Make sure the video transmitter

is powered on and transmitting.

Transmitter and headset not

on the same band

Use the spectrum analyzer on

the video receiver module to ﬁ nd

the correct frequency/ band.

Horizontal lines in the

headset display

Digital interference on the

selected channel

Choose a cleaner channel

Blurry Image

Camera is out of focus

Rotate the lens slowly to focus

the camera

Users who require glasses

may need prescription

inserts

Consider diopter inserts to meet

your optical needs. See page 7

for more information.

Illegible DVR menu

Video receiver is powered

on

Turn off power switch to video

receiver on the bottom of the

headset

External AV source plugged

into headset

Remove external AV source

DVR not recording

SD card full

Format SD card. Move any ﬁ les

you want to keep off the SD

card before formatting.

SD card corrupted Replace the SD card

Attempting to power on

the DVR too soon before

the LED light cycles on and

back off

Power off the headset and

then back on. Wait for the LED

to turn off before turning on

the DVR.

Head tracker not

working

Programming errors in your

transmitter

Conﬁ rm channel assignments

and operation in the

transmitter servo monitor.

Head tracker not initialized

Conﬁ rm center position, then

press HT button to initialize

head tracker

Head tracker working

but not centering well

Leaning against a car or

other large metallic objects

can affect the magnetic

sensor in the head tracker

Select a location to operate

located away from large

metallic objects

18

1-YEAR LIMITED WARRANTY

What this Warranty Covers - Horizon Hobby, LLC, (Horizon) warrants to the original

purchaser that the product purchased (the “Product”) will be free from defects in materials

and workmanship for a period of 1 year from the date of purchase.

What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic

damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial

use, or due to improper use, installation, operation or maintenance, (iii) modiﬁ cation of or

to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby

authorized service center, (v) Product not purchased from an authorized Horizon dealer, (vi)

Product not compliant with applicable technical regulations, or (vii) use that violates any

applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL

SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive

remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product

determined by Horizon to be defective. Horizon reserves the right to inspect any and all

Product(s) involved in a warranty claim. Service or replacement decisions are at the sole

discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND

EXCLUSIVE REMEDY.

Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN

CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF

LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Further, in no event shall the liability of Horizon exceed the individual price of the Product

on which liability is asserted. As Horizon has no control over use, setup, ﬁ nal assembly,

modiﬁ cation or misuse, no liability shall be assumed nor accepted for any resulting damage

or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you

as the purchaser or user are not prepared to accept the liability associated with the use of

the Product, purchaser is advised to return the Product immediately in new and unused

condition to the place of purchase.

Law - These terms are governed by Illinois law (without regard to conﬂ ict of law principals).

This warranty gives you speciﬁ c legal rights, and you may also have other rights which vary

from state to state. Horizon reserves the right to change or modify this warranty at any time

without notice.

WARRANTY SERVICES

Questions, Assistance, and Services - Your local hobby store and/or place of purchase

cannot provide warranty support or service. Once assembly, setup or use of the Product

has been started, you must contact your local distributor or Horizon directly. This will enable

Horizon to better answer your questions and service you in the event that you may need

19

any assistance. For questions or assistance, please visit our website at horizonhobby.com,

submit an inquiry to productsupport@horizonhobby.com or call the toll-free telephone

number referenced in the Warranty and Service Contact Information section to speak with a

Product Support representative.

Inspection or Services - If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in, please use the Horizon Online

Service Request submission process found on our website or call Horizon to obtain a Return

Merchandise Authorization (RMA) number. Pack the Product securely using a shipping

carton. Please note that original boxes may be included, but are not designed to withstand

the rigors of shipping without additional protection. Ship via a carrier that provides tracking

and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise

until it arrives and is accepted at our facility. An Online Service Request is available at http://

www.horizonhobby.com/content/_service-center_render-service-center. If you do not have

internet access, please contact Horizon Product Support to obtain a RMA number along with

instructions for submitting your product for service. When calling Horizon, you will be asked

to provide your complete name, street address, email address and phone number where you

can be reached during business hours. When sending product into Horizon, please include

your RMA number, a list of the included items, and a brief summary of the problem. A copy

of your original sales receipt must be included for warranty consideration. Be sure your

name, address, and RMA number are clearly written on the outside of the shipping carton.

Provided warranty conditions have been met, your Product will be serviced or replaced free

of charge. Service or replacement decisions are at the sole discretion of Horizon.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a

LiPo battery, please contact the appropriate Horizon Product Support ofﬁ ce.

Warranty Requirements- For Warranty consideration, you must include your

original sales receipt verifying the proof-of-purchase date.

Non-Warranty Service - Should your service not be covered by warranty, service will be

completed and payment will be required without notiﬁ cation or estimate of the expense

unless the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁ cation. Service estimates are

available upon request. You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition

you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as

well as Visa, MasterCard, American Express, and Discover cards. By submitting any item

to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our

website http://www.horizonhobby.com/content/_service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of

use and ownership. If received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging return shipment of the un-

serviced Product, through a carrier of the sender’s choice and at the sender’s

expense. Horizon will hold non-compliant Product for a period of 60 days from

notiﬁ cation, after which it will be discarded.

10/15

20

NOTICE: Modiﬁ cations to this product will void the user’s authority to

operate this equipment.

Warranty and Service Contact Information

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center

(Repairs and Repair

Requests)

servicecenter.horizon-

hobby.com/RequestForm/

4105 Fieldstone Rd

Champaign, Illinois,

61822 USA

Horizon Product Support

(Product Technical As-

sistance)

productsupport@

horizonhobby.com.

877-504-0233

Sales

websales@horizonhobby.

com

800-338-4639

FCC ID: BRWDXMTX10

This equipment has been tested and found to comply with the limits for Part 15 of

the FCC rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates uses

and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

IC: 6157A-BRWDXMT

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may notcause

interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operation of the device.”

La pagina sta caricando ...

Spektrum Focal DVR FPV Headset Manuale utente

Questo manuale è adatto anche per

Spektrum Focal DVR FPV Headset Manuale utente

in altre lingue

Documenti correlati

Altri documenti