Waring Commercial WFP16SCDK Manuale utente

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto,

siempre lea las instrucciones cuidadosamente antes de usarlo.

An que votre appareil vous procure en toute sécurité beaucoup

de satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

Lees alle instructies zorgvuldig door, alvorens u het product gebruikt,

zodat uw veiligheid en gebruiksgemak gewaarborgd worden.

Zu Ihrer eigenen Sicherheit und für langfristige Freude an diesem Produkt,

lesen Sie vor der Benutzung immer sorgfältig die Gebrauchsanweisung.

Per un funzionamento sicuro e duraturo di questo prodotto

leggere sempre le istruzioni prima dell’uso.

Para sua segurança e usufruto contínuo deste produto,

ler sempre atentamente o manual de instruções antes de usar.

В целях обеспечения безопасности и надлежащего использования электроприбора

просьба тщательно ознакомиться с руководством по эксплуатации.

WFP16SCDE / WFP16SCDK

3.75L FOOD PROCESSOR

PROCESADOR DE ALIMENTOS DE 3,75 L

ROBOT MULTIFONCTION DE 3,75 L

KEUKENMACHINE 3,75 LITER

3.75L KÜCHENMASCHINE

MIXER CON CAPACITÀ DI 3,75 L

3,75L PROCESSADOR DE ALIMENTOS

КУХОННЫЙ КОМБАЙН С ОБЪЕМОМ ЧАШИ 3,75 Л

2

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should

always be taken including the following:

1. READ ALL INSTRUCTIONS.

2. Unplug from outlet when not in use, before putting on

or taking off parts, before removing food from work

bowl, and before cleaning. To unplug, grasp plug when

pulling from electrical outlet. Never pull cord.

3. Unplug from outlet prior to handling or cleaning the unit.

4. Blades are sharp. Handle carefully.

5. This product is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge.

6. Your Waring® Commercial food processor is a piece of

kitchen equipment, and like all other kitchen equipment,

extreme care must be used when operating it. Although

training requirements are minimal, only responsible and

prudent individuals should be allowed to operate this food

processor. It should not be used by or near children or

individuals with certain disabilities.

7. To avoid injury, never place cutting blade or disc on base

without rst having put the bowl properly in place.

8. Keep hands as well as spatulas and other utensils away

from moving blades or discs while processing food to

prevent the possibility of severe personal injury or damage

to the food processor. A plastic scraper may be used, but

must be used only when the food processor is not running.

9. To protect against risk of electrical shock, do not put base in

water or other liquids.

10. Avoid contact with moving parts. Never feed food by hand

when slicing or shredding. Always use food pusher.

11. Make sure motor has completely stopped before removing

the cover.

3

12. Do not operate any appliance with a damaged cord or plug,

or after appliance has been dropped or damaged in any

manner. Return appliance to the nearest authorized service

facility for examination, repair or adjustment.

13. The use of attachments not recommended or sold by

Waring Commercial may cause re, electric shock or injury.

14. Do not use outdoors.

15. Do not let cord hang over edge of table or counter, or touch

hot surfaces.

16. This product is ETL listed for household use. Use it only for

food preparation as described in this book.

17. Do not attempt to disable the cover interlock mechanism.

18. Be certain cover is securely locked in place before operating

appliance.

19. If the machine malfunctions for any reason, discard any food

being processed at that time.

20. Children should be supervised to ensure that they do not

play with the appliance.

21. Caution: Do not use dicing application (WFP16S13) with

220-240V CE-approved versions.

22. Be careful if hot liquid is poured into the food processor or

blender as it can be ejected out of the appliance due to a

sudden steaming. This food processor is not intended to be

used for hot recipes.

SAVE THESE INSTRUCTIONS

4

TYPE F PLUG

(GERMANY, AUSTRIA, NETHERLANDS,

SWEDEN, NORWAY, FINLAND,

PORTUGAL, SPAIN, EASTERN EUROPE)

This grounded plug has two round prongs and

there are two grounding clips on the side of the

socket. This plug is non-polarized so the plug can

be inserted in either direction into the socket.

Grounding is accomplished when the clip on the

socket meets the contact on the plug. Ensure that

the plug is fully inserted.

TYPE G PLUG

(UNITED KINGDOM, IRELAND,

CYPRUS, MALTA, MALAYSIA,

SINGAPORE AND HONG KONG)

This grounded plug has three rectangular prongs

that form a triangle. Line up the prongs to the

socket and ensure that the plug is fully inserted.

This plug is also fuse-protected for power surges.

Correct Disposal of this product

This marking indicates that this product should

not be disposed with other household wastes

throughout the EU. To prevent possible harm to the

environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote

the sustainable reuse of material resources. To

return your used device, please use the return and

collection systems or contact the retailer where the

product was purchased. They can take this product

for environmentally safe recycling.

TO ENSURE PROPER USE OF THIS UNIT, PLEASE SEE

IMPORTANT GROUNDING INSTRUCTIONS BELOW. PRIMARY

COUNTRIES USING THE DIFFERENT PLUG TYPES ARE LISTED

FOR REFERENCE ONLY. REFER TO THE ACTUAL UNIT TO

DETERMINE WHICH PLUG TYPE IS APPLICABLE.

5

INTRODUCTION

Waring® Commercial food processors are the most versatile in

their class, featuring a seal system that enables processing of

large volumes of liquid without leakage and eliminates the need to

remove the S-blade while pouring. These professional machines

are prime examples of Waring’s seventy-ve years of industry

food service experience, as well as seventy-ve years of food

processing experience.

This comes with a sealed work bowl (also known as a batch

bowl) and a sealed/locked cutter blade (or S-blade) to CHOP,

GRIND, PURÉE and MIX. The patented seal system allows for

processing large volumes of liquids with no leakage. Additional

discs provided allow for shredding, slicing and whipping directly

in the sealed batch bowl. For large volume processing, this food

processor includes a continuous feed chute. This option allows

anything processed with an accessory disc to be processed

directly into a separate container.

Size, power and convenience

The wide feed tube makes processing high volumes of larger

sized foods convenient and easy. The motor shaft is built for

durability. The housing, work bowl, chute, covers and pushers are

all made from durable polycarbonate for heavy-use conditions

and easy cleanup. The clear bowl and processing covers are

convenient for viewing food processing and are made of

heavy-duty material to withstand heavy-duty use.

6

THE PARTS

The Waring® Commercial food processor consists of the

following standard parts and accessories:

1. Die-cast motor base with vertical heavy-duty shaft

2. Three control buttons

a. OFF

b. ON

c. PULSE

3. Safety interlock (not shown). Prevents machine from

operating until cover is in place

4. Sealed clear 3.75L work bowl

5. Sealed clear work bowl cover

a. Small pusher used within the large pusher for smaller

vegetables, pepperoni, etc.

b. Large pusher with full-size and reduced-size feed

options

c. Large feed tube for maximum use of cutting surface

Note: This combination pusher allows use of the entire feed

tube for large foods and provides controlled processing for

small-diameter foods such as carrots, celery and pepperoni.

6. Sealed S-blade (cutter blade) to chop, grind, purée and mix:

Locks in place for liquid processing and easy pouring

7. Adjustable slicing disc

8. Reversible shredding disc

9. Sealed whipping disc

10. Detachable disc stem for use with adjustable slicing disc and

reversible shredding disc

11. Cleaning brush (not shown)

12. Continuous feed chute

13. Continuous feed chute cover

14. Slinger

7

1

4

5

6

7

9

10

8

12

13

14

5a.

5c.

22a. 2b. 2c.

5b.

8

ASSEMBLY OF BATCH BOWL PARTS

We will use the terms work bowl, batch bowl and cutter bowl

interchangeably throughout this instruction book. They mean the

same thing.

Prior to First Use:

• Clean and sanitize the motor base. Wash, rinse, and sanitize

the work bowl, cover, food pusher, food pusher insert and

accessories.

• Place base on a counter or table near an electrical outlet.

Position it so you look at the front of the unit and can see the

control panel. Do not plug in the cord until the processor is

completely assembled.

• Pick up the transparent work bowl, holding it in both hands with

the handle toward you.

• Place the bowl on the base, tting its central tube over the

motor shaft on the base and placing its handle slightly to the

left of back-center (at about a 7 o’clock position).

• Press the bowl down so the lower rim ts around the circular

platform. Turn the bowl counterclockwise as far as it will go. It

will lock into position with the tabs on the sides of the

platform.

Read this if assembling the batch bowl parts to use S-blade

(cutter blade) or whipping disc.

• Pick up the S-blade or whipping disc, noting the diagram on

the top of the plastic center. It matches the shape of the motor

shaft.

• Place the S-blade or whipping disc over the tip of the motor

shaft, lining up the inside of the hub with the shaft. Press it

down rmly, rotating the center hub until the blade or disc

assembly is fully seated. It should easily drop into place. Push

rmly to lock and seal S-blade or whipping disc hub in place.

Be sure it is pushed down as far as it will go. If it is not all the

way down, it may become damaged and liquid may leak.

Push only on the center section (plastic part); never touch

the cutting blade, as it is extremely sharp.

• Check to be sure the blade or disc is all the way down by

turning it back and forth while gently pushing it down. If

properly installed and fully seated, the lower blade will be

positioned just above the inside bottom of the bowl.

9

• If processing food with the S-blade or whipping disc, now is the

time to add the food or liquid to the work bowl.

• Do not ll liquid over MAX LIQUID FILL LINE. If too much

liquid is used, it will overow. In this case, stop operation,

remove liquid to below MAX LIQUID FILL LINE and continue

processing.

Read this if assembling batch bowl parts to use accessory

discs in batch bowl.

To assemble the adjustable slicing disc (WFP16S10), you must

remove bowl cover. Position the disc stem over the drive shaft

securely. Next, select the desired thickness setting on your

adjustable slicing disc. There are 16 different positions ranging

from 1–6mm in thickness. Once you’ve set the thickness, position

the plastic receptacle over the disc stem securely. Do not turn on

the unit until the batch bowl is properly assembled with the cover.

To assemble the reversible shredding disc (WFP16S12), you must

remove bowl cover. Position the disc stem over the drive shaft

securely. Next, select the desired shredding blade size. Your

reversible shredding disc has ne shredding blades on one side

and medium shredding blades on the other. Be sure the desired

blade size is facing up, and position the disc on the disc stem

securely. Do not turn on the unit until the batch bowl is properly

assembled with the cover.

NEVER ATTEMPT TO START THE FOOD PROCESSOR

WITHOUT THE COVER LOCKED INTO POSITION.

Two pushers for feed tube

There is a large food pusher and small food pusher. The large

pusher is for processing larger foods. The small pusher nests in

the large pusher and can be used for smaller products, guiding

long thin vegetables for more precise cuts, or for jobs like slicing

pepperoni. Insert the small food pusher into the large food pusher

opening. Now you are ready to insert the large pusher into the

feed tube opening.

NOTE: There is a long pin on the front side of the large pusher.

The food processor will not operate until the pin is properly

activating the interlock system.

10

DISASSEMBLY OF BATCH BOWL PARTS

ALWAYS UNPLUG THE UNIT BEFORE DISASSEMBLING.

• Remove the large food pusher from the feed tube. Remove the

small pusher from the large pusher.

Disassembly when removing the S-blade or

whipping disc

• Remove the work bowl from the unit by rotating clockwise

(left) to disengage the tabs on the bottom of the bowl platform

from the work bowl. When the bowl handle is on the left

(about 7 o’clock position), you can gently lift the bowl straight

up and out.

It is recommended that you remove the bowl from the motor

base before you remove the S-blade or whipping disc.

NOTE: REMOVE ALL FOOD AND LIQUID BEFORE REMOVING

S-BLADE OR WHIPPING DISC, OR BOWL WILL LEAK.

• To remove the blade or disc, keep a slight downward pressure

on the top center hub of the blade or disc while removing the

bowl from the motor base. This will form a seal to prevent food

particles from spilling into the center tube of the bowl and onto

the motor base or the work surface. Remove all contents from

the batch bowl. Then remove the S-blade or whipping disc

from the bowl by pulling upward to unlock the seal. Handle the

S-blade with caution; the blades are extremely sharp.

Disassembly when removing an accessory disc

• Do not remove the work bowl until the accessory disc is

removed.

• To remove an accessory disc, place your ngers on the outer

edge of two opposite sides of the disc and lift. The disc should

come off the disc stem easily. If the disc stem stays attached

to the disc, hold the disc in one hand with the stem facing away

from your hand and pull out the disc stem. Be careful not to

scrape your hand on any sharp edges.

• Remove the work bowl from the unit by rotating clockwise (left)

to disengage the tabs on the bottom of the bowl platform

from the work bowl. When the bowl handle is on the left (about

7 o’clock position), you can gently lift the bowl straight up and out.

11

ASSEMBLY OF CONTINUOUS-FEED CHUTE PARTS

• Clean and sanitize the motor base, and wash, rinse, and sanitize

the continuous-feed chute, cover, slinger disc, food pusher,

food pusher insert and processing tools prior to initial use.

• Place the base on a counter or table near an electrical outlet.

Position it so that you are looking at the front of the unit and can

see the control panel. Be certain that the cord is unplugged.

Do not plug in the cord until the processor is completely

assembled.

• Pick up the continuous-feed chute, holding it in both hands with

the chute pointing in the 4-o’clock position and the handle at

the 10-o’clock position. Place the chute on the base, tting its

center opening over the motor shaft.

• Press the chute down so the round lower rim of the chute ts

around the circular platform. Rotate counterclockwise until it

clicks into place and engages the rear interlock.

• Place the slinger (or ejector disc) in the bowl, sliding it over the

metal motor shaft until it reaches the bottom of the chute.

• Select the appropriate accessory disc. Follow directions on

page 9 to attach stem to disc.

• Place the cover on top of the chute with cover locking tab at

left of locking tab on chute. Press down and rotate the cover

until it latches to the tab on the continuous-feed chute. This will

prevent the lid from rising up during processing.

• The interlock tab on the cover will slide into the interlock slot on

the cover and engage the magnetic safety interlock switch. The

interlock switch prevents operation of the machine unless the

cover is in the proper position. With this switch engaged, the

food processor will operate if the power is on and the controls

are turned to ON or PULSE.

NEVER ATTEMPT TO START THE FOOD PROCESSOR

WITHOUT THE CHUTE AND COVER LOCKED INTO

POSITION.

• Insert the small food pusher into the large food pusher opening.

Now you are ready to insert the large pusher into the feed tube

opening.

• Once feed chute is assembled, place separate container under

the feed chute.

12

DISASSEMBLY OF CONTINUOUS-FEED

CHUTE PARTS

ALWAYS UNPLUG THE CORD BEFORE DISASSEMBLING.

• Turn the cover clockwise until the safety interlock tab on the

cover is disengaged from the safety interlock switch on the

chute, and the tabs are clear of the tabs on the cover.

• Remove the large food pusher from the feed tube. Remove the

small pusher from the large pusher.

• Remove the continuous-feed chute from the motor base. If the

chute is pointing in the 4-o’clock position, just lift it up. If not,

rotate clockwise to disengage the tabs on the bottom of the

chute platform (motor base) from the slots on the bottom of the

continuous-feed chute.

• Use caution removing accessory discs, as the blades are

very sharp.

OPERATING THE CONTROLS

• Plug the machine into an electrical outlet.

• There are three control buttons on the base unit.

The three controls are: ON

OFF

PULSE

How they work: ON: Press the ON button to start

the motor.

OFF: Press the OFF button to stop

the motor.

PULSE: To pulse the motor, press the

PULSE button down, then

release. The motor will run as

long as you hold the button

down; it stops when you

release the button.

13

HOW TO USE

Continuous use

For continuous processing, use the ON button which is located in

the middle.

Pulsing

• For rapid ON/OFF operation, use the PULSE. The motor runs as

long as you hold the button down; it stops when you release the

button.

• You control the duration of each pulse by the amount of time

you hold the button down. You control the frequency of pulses

by the rate at which you press the button.

• Pulsing gives you greater control over consistency when

chopping, blending and mixing.

• Pulsing is also useful in processing hard foods. Pulse the food

a few times to break it up into smaller parts. Then proceed with

continuous use after the pieces are broken up and easier to

process.

• Always use the PULSE button for pulsing. Never move the

bowl and cover assembly on or off to control pulses. It is less

efcient and could damage the machine.

Turning the machine off with the OFF button

• Always switch the food processor off by pressing and releasing

the OFF button. This assures that the power is not supplied to

the motor.

• Always switch the food processor off and wait until rotation

stops before removing the cover.

• While the safety interlock switch will turn the machine off if the

bowl is rotated clockwise or the cover is removed while running,

this should not be the means of turning the machine on or off.

• As a safety precaution, always make sure the machine is off by

pressing the OFF button before pushing down the lid.

14

FOOD PREPARATION

• Prepare all food items to be processed by washing and peeling

as required. Remove pits, stones, and large seeds.

• Cut vegetables, meats, cheeses, etc. into sizes that will t

into either the small or large feed tube for processing with

accessory discs.

• Preparation for slicing: Produce that is long and cylindrical such

as carrots, cucumbers and celery should be cut at at both

ends. This will provide a consistent slice for all food processed.

FOOD PUSHER SELECTION

The feed tube can be used for adding ingredients while the food

processor is running. However, it is recommended that the food

pushers be left in place whenever possible to prevent splashing

and avoid unwanted additions to the work bowl.

Small pusher

This pusher is typically used when inserting vegetables vertically

for smaller cuts. It should be used when slicing foods such as

carrots, celery, pepperoni, etc., when a consistent, at result is

desired.

Large pusher

This pusher is typically used when inserting vegetables

horizontally for longer cuts.

RESETTING THERMAL PROTECTION

This food processor is equipped with an automatic reset switch

to protect the motor from overheating.

If your food processor stops running under heavy use, press the

OFF button and unplug the power cord. Empty the work bowl of

all its contents and discard. Allow approximately 30 minutes for

the motor to cool down.

Reassemble unit, plug the power cord back into the outlet and

run rst with the bowl empty. Put food into the bowl and continue

processing.

15

If your food processor does not function properly following

this procedure, discontinue use and contact a Certied Waring

Customer Service Center.

USE INSTRUCTIONS FOR S-BLADE

(CUTTER BLADE)

• The sealed S-blade (cutter blade) is designed for chopping,

grinding, puréeing, blending, mixing or kneading.

• Assemble the bowl and blade as instructed in the section titled

“Assembly of Batch Bowl Parts” (page 8).

Chopping or mincing

• To chop or mince in the bowl, ll the bowl up to ¾ full.

• To chop or mince most effectively, use the PULSE function.

This allows for better control over consistency. Continue pulsing

until the desired consistency has been reached.

• If chopped foods are processed continuously, the food could

be processed unevenly, i.e., food on the bottom will be nely

chopped and food on the top will be more coarse.

Chopping meat

Cut meat into 1-inch (2.5 cm) pieces to ensure an even chop.

Process no more than 2.25 lb. (1 kg) of meat. Press the PULSE

button 3 or 4 times at a rate of 1 second on, 1 second off.

If the food is not chopped ne enough, let the processor run

continuously for a few seconds. If the machine has trouble

starting, reduce the amount of meat in the bowl and start again.

Chopping/grating hard cheese

To chop, put up to 2 lb. (910 g) of uniformly cut 1-inch (2.5 cm)

cubes of chilled cheese into the bowl and pulse. For grated

cheese, pulse until the cheese is in small chunks (pea size), then

allow the processor to run continuously until you have the degree

of grating desired. Cheese with high moisture content can ball up

if processed too long.

Chopping onions, celery, cabbage, etc.

Cut onions into quarters, and other vegetables into 1-inch

(2.5 cm) cubes. Put the cubed food into the work bowl up to

16

the top of the bowl’s inner tube, and pulse until you reach the

desired consistency.

Note: If you let the blade run too long, the ingredients on the

bottom will become puréed or give you uneven results.

Purée or mix

To purée tomatoes, vegetables and fruits, make sauces, or mix

and blend ingredients, put the ingredients into the bowl, turn the

unit on and allow it to run continuously until you reach the

desired consistency. Do not let the machine run unattended.

If too much liquid is used, it will overow. In this case, stop

operation, remove liquid to below the MAX FILL LINE and

continue processing.

Do not ﬁll liquid past MAX LIQUID FILL LINE.

ACCESSORY DISC SELECTION AND USE

The food processor disc accessories are made to perform a

wide variety of food processing tasks: slicing, whipping,

shredding. Three (3) accessory discs are included. As of

this printing they are:

WFP16S10 - Adjustable Slicing Disc

WFP16S11 - Sealed Whipping Disc

WFP16S12 - Reversible Shredding Disc

SLICING OPERATION

• This food processor comes with an adjustable slicing disc.

The adjustable slicing disc allows you to slice foods anywhere

from 1 to 6mm thick using 16 different slicing positions!

Prior to mounting the disc onto the motor shaft (see page

9 for assembly instructions), use the knob to select desired

thickness. Once you have selected the thickness and mounted

the disc onto the unit, you may secure the cover onto the batch

bowl or continuous-feed chute and remove the pusher.

• Prepare all food items to be processed by washing and peeling

as required. Remove pits, stones, and large seeds. Be sure the

food will t into the proper feed chute. Foods such as carrots,

cucumbers, etc., should be cut at at both ends to provide a

consistent slice throughout the whole product.

• With foods like cabbage, lettuce or any product that has an

undesirable core, the core should be removed. Medium-size

17

cabbage or lettuce heads may be cut into thirds to t in the

feed chute. Larger heads may need to be quartered.

• When food preparation is complete, ll the chosen feed tube,

position the pusher, turn the machine on and monitor the

results. NOTE: Do not ll food over MAX FILL LINE on the

feed tube of the batch bowl lid when processing with the large

pusher.

• Never try to slice soft cheese. Use only hard cheese.

Mozzarella may be sliced only when well chilled to around 36˚F.

• When sliced food reaches nearly full capacity of the bowl,

remove all sliced food from the bowl.

SHREDDING OPERATION

• This food processor comes with a reversible shredding disc.

Both sides on this disc produce a perfect shred, one ne, the

other medium. When assembling the shredding disc, note that

the side facing up will be the size shred produced. When the

disc is secured, you may attach the cover on the batch bowl or

continuous-feed chute and remove the pusher.

• Prepare all food items to be processed by washing and peeling

as required. Remove pits, stones, and large seeds. Be sure the

food will t into the proper feed chute.

• NOTE: Do not ll food over MAX FILL LINE on the feed tube of

the batch bowl lid when processing with the large pusher.

• Select which feed tube to use. Horizontal placement of foods

such as carrots and zucchini will result in a longer shredded

product. Using the smaller chute and small pusher with food

inserted vertically will yield a shorter shredded product.

• Never try to shred soft cheese. Use only hard cheese.

Mozzarella may be shredded only when well chilled to about

36˚F. Always use PULSE operation when shredding cheese.

• When shredded food reaches nearly full capacity of the bowl,

remove all shredded food from the bowl.

SEALED WHIPPING DISC OPERATION

• This food processor comes with a sealed whipping disc. See

page 8 for assembly instructions to install the whipping disc.

Once assembled, you are ready to start adding in your favorite

ingredients!

18

• The whipping disc makes any whipping job easy and quick.

During the whipping process, air is added to the mixture. As air

is added, the mixture expands. Be sure that the mixture does

not expand beyond the MAX FILL LINE or it may leak through

the feed tube. If the mixture expands to the point where it leaks

out the feed tube, stop operation and reduce the contents of

the bowl to below the MAX LIQUID FILL LINE and continue

operation.

For whipped cream, simply add heavy cream and your choice

of avoring. Be sure the bowl is properly assembled with the

bowl cover. Press the ON button for continuous operation and

whip the cream until thick and uffy.

To make butter, add heavy cream and your choice of

seasoning into the batch bowl. Be sure the bowl is properly

assembled with the bowl cover. Press the ON button for

continuous operation and whip the cream until the moisture

has mostly separated from the cream.

For whipping cream do not use more than 6 cups of heavy

cream. If it overows, stop operation, remove liquid to below

MAX FILL LINE and continue.

GRATING OPERATION

Waring Commercial offers grating discs as an optional accessory.

For grating, use instructions below.

• Prepare all food items to be processed by washing and peeling

as required. Remove pits, stones, and large seeds. Be sure the

food will t into the proper feed chute.

• Never try to grate soft cheese. Use only hard cheese.

Mozzarella may be grated only when well chilled to

around 36° F.

• For grating cheese, it is recommended that a slight pulsating

pressure be applied with the pusher, alternating push/no push

until the cheese block is completely grated. Cheese grating

puts more strain on the food processor motor than other tasks

and may cause overheating if too much pressure is applied in

a continuous manner.

• You can typically expect to grate 10 pounds (4.5 kg) of cheese

in about ve (5) minutes.

• After ve (5) minutes of continuous cheese grating, allow the

machine to cool.

19

• It is recommended that you plan your food preparation in a

manner that will allow for ve minutes of grating, followed by

ve minutes of food preparation while the machine rests.

• When grated food reaches nearly full capacity of the bowl,

remove all grated food from the bowl.

TROUBLESHOOTING

This section describes potential problems and the correct

solutions for them. Problems that cannot be solved with the

guidelines listed below should be referred to one of the Waring

Authorized Service Centers for assistance. A listing of authorized

service agencies is supplied with each Waring food processor.

Unit does not start when assembled correctly

• Pull the plug and try plugging into another outlet.

• Make sure the bowl is properly positioned on the motor base,

that the bowl cover is attached properly, and that the safety

interlock tab on the cover has properly engaged the safety

interlock switch.

• Press ON button.

Unit stops running during processing

• The unit may have overheated. Refer to Resetting Thermal

Protection section (page 14).

• Turn unit off and unplug.

• Remove bowl attachment.

• Remove food being processed from inside the bowl and

discard.

• Allow unit to cool for 30 minutes.

• Reassemble unit, and run rst with the bowl empty, then put

food into the bowl and try again.

Unit jams or vibrates excessively

• Turn unit off and unplug.

• Disassemble the batch bowl/accessories.

• Make sure there is no food in S-blade hub (if applicable).

• Clean food off accessory discs (if applicable).

• Reassemble unit, and run rst with the bowl empty, then put

food into the bowl and try again.

20

Unit will not come up to full speed

• Bowl is overloaded – remove food being processed and reload

using smaller quantities.

If unit does not operate after you have followed the above

• Check outlet to be sure there is current.

• Check to be sure circuit breaker is on.

• Check to be sure the fuse is not blown if there are fuses on this

circuit.

• Call a local Waring service agency.

If food processor makes grinding noise

• Turn unit off, unplug, disassemble, check bowl and blade to

see if they have been rubbing together.

• If bowl and blade are rubbing, call your authorized Waring

service agency.

CLEANING AND MAINTENANCE

Clean the food processor and accessories prior to initial use and

after each use. Do not use harsh abrasive-type cleaners on any

part of the food processor. Cleaning must follow ETL sanitation

guidelines.

Wash the motor shaft with a small brush.

Wash, rinse, sanitize and dry the bowl, cover, small food pusher,

large food pusher, accessory discs, and S-blade prior to initial

use and after use, unless they will be used again immediately.

These items are all dishwasher safe, and may be cleaned and

rinsed in the dishwasher instead of manually in the sink.

Wash and rinse all of the above items after each use.

A stiff bristle brush will help to knock food particles out of the

crevices of the discs and blades before washing. Handle very

carefully as the blades are sharp.

For manual cleaning, it is recommended that you use washing

solutions based on non-sudsing detergents, and chlorine-based

sanitizing solutions that have a minimum chlorine concentration of

100 PPM. The following washing, rinsing, and sanitizing solutions,

or their equivalents, may be used:

La pagina sta caricando ...

Waring Commercial WFP16SCDK Manuale utente

Waring Commercial WFP16SCDK Manuale utente

in altre lingue

Documenti correlati

Altri documenti