Silca Smart Software Manual

Marca: Silca

Modello: Smart

Tipo: Software Manual

SMART

Remote Programmer

So ware Guide

vers. 1.2

SMART Remote Programmer

Fig./Abb.1

Fig./Abb.2

Fig./Abb.3

3Copyright Silca S.p.A. 2017

SMART Remote Programmer

Fig./Abb.4

Fig./Abb.5

Fig./Abb.6

SMART Remote Programmer

This manual has been drawn up by Silca S.p.A.

without the approval of Silca S.p.A.

Edition: February 2017

by SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italy

La stesura di questo manuale è stata curata da Silca S.p.A.

Tutti i diritti sono riservati. Nessuna parte della pubblicazione può essere riprodotta o diffusa con un mezzo qualsiasi (fotocopie,

microﬁ lm o altro) senza il consenso di Silca S.p.A.

Edizione: Febbraio 2017

Da SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italia

Dieses Handbuch wurde von Silca S.p.A. herausgegeben.

S.p.a.

Ausgabe: Februar 2017

von SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italie

Ce mode d’emploi a été rédigé par SILCA S.p.A.

Tous les droits sont réservés. Aucune partie de cette publication ne pourra être reproduite ou divulguée quel que soit le moyen

utilisé (photocopies, microﬁ lm ou autre) sans le consentement écrit préalable de SILCA S.p.A.

Edition: Février 2017

par SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italie

Este manual ha sido redactado por Silca S.p.A.

Reservados todos los derechos. Ninguna parte de la publicación puede ser reproducida o difundida con cualquier medio fotocopias,

microﬁ lm u otro) sin el permiso de Silca S.p.A.

Edición: Febrero 2017

Por SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italia

Este manual foi redigido pela Silca S.p.A.

microﬁ lmes ou outro) sem a autorização da Silca S.p.A.

Edição: Fevereiro 2017

pela SILCA S.p.A.

Via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Itália

Deze handleiding werd opgesteld door de ﬁ rma Silca S.p.A.

Alle rechten zijn voorbehouden. Geen enkel deel van deze publicatie mag vermenigvuldigd of verspreid worden, door gelijk welk

hulpmiddel (fotokopieën, microﬁ lms of andere hulpmiddelen), zonder toestemming van de ﬁ rma Silca S.p.A.

Editie: Februari 2017

door SILCA S.p.A.

via Podgora, 20 (Z.I.) 31029 VITTORIO VENETO (TV) - Italië

SMART Remote Programmer

English

5Copyright Silca S.p.A 2017

OPERATING GUIDE  SOFTWARE FEATURES

WARNINGS

1 - FOR PROPER AND RELIABLE OPERATION, KEEP THE SMART REMOTE PROGRAMMER AWAY FROM ANY

SOURCES OF RADIO INTERFERENCE, SUCH AS:

- CORDLESS PHONES

- ELECTRIC MOTORS

- NEON LIGHTS

- WI-FI MODEMS

2 - BEFORE INSTALLING “SMART REMOTE PROGRAMMER SOFTWARE” APP, MAKE SURE THE USB CABLE

IS NOT CONNECTED TO PC

PC PROGRAM

SMART Remote Programmer So ware Program has been developed to allow interfacing the SMART Remote

programmer device with informa on released by Silca.

The program can be freely downloaded from www.silca.biz/www.ilco.us website, and it run on Windows®

Vista, 7, 8 and 10.

The ﬁ rst  me the program is run, SMART Remote programmer device must be connected to PC, using a wizard

(see sec on “First program start”). Device must be connected to PC, at every program start.

FIRST PROGRAM START

Before star ng applica on: make sure SMART Remote Programmer device is connected to PC through a

special USB cable (supplied with the device).

USB driver installation procedure:

- For Windows 8 and Windows 10 ® Opera ng systems, connec ng your PC to the internet, drivers are auto-

ma cally installed by the opera ng system.

- For Vista and Windows 7 ® Opera ng systems, you will have to manually install USB drivers stored in the

Program File folder...\ Silca So ware\Silca SMART Remote Programmer\driver.

The first time the program is run, the following actions are required:

1. Program conﬁ gura on;

2. Device mandatory registra on;

3. Device conﬁ gura on;

SMART Remote Programmer

English

PROGRAM CONFIGURATION

The following window allows you to conﬁ gure the program.

Following informa on should be entered:

Language: This is the language of the program

Preferred region:favourite area for displaying auto-selectable models (AMERICA, ASIA, EUROPE)

Brand: ILCO/SILCA reference mark for displaying ar cle codes and remote control part code to be used

In Area 1, bu ons are available to allow you to move forward or backward within windows during the ﬁ rst

conﬁ gura on of the program.

HOW TO EDIT SOFTWARE PREFERENCES

Once you have set so ware preferences, you can change them by selec ng the icon and by clicking in

the Save bu on

you can save all entered se ngs.

SMART Remote Programmer

English

7Copyright Silca S.p.A 2017

HOW TO REGISTER AND CONFIGURE YOUR DEVICE

1. REGISTRATION

To proceed to the next step, you need to REGISTER your device via web through the icon .

Make sure your pc has a reliable Internet connec on before proceeding.

Please ﬁ ll out the form with the required data and send it back.

You will receive a veriﬁ ca on email containing a link that you’ll need to click or tap to conﬁ rm.

2. CONFIGURATION

“RegistraƟ on status”: shows whether the device is registered.

“About the device”: contains all the informa on about the device.

- So ware Guide: bu on for direct access to the so ware guide;

- News: bu on for access to the news, if available.

- Serial number: connected device serial number

- Firmware: ﬁ rmware version installed on your device

- Database: database version inside your device

- So ware: SRP program version installed

Note: if no data is displayed, please make sure the device is connected to PC via USB.

In Area 1, bu ons are available to allow you to move forward or backward within windows during the ﬁ rst

conﬁ gura on of the program.

In Area 2, three Update bu ons are available to allow you upgrading ﬁ rmware of your device and upda ng

program database, and the program itself, with the latest version available online.

SMART Remote Programmer

English

LAUNCHING A PROGRAM

In Area 1 bu ons are available to allow you to access the various func ons displayed in Area 2.

Area 1 descrip on bu ons:

This bu on leads you to the start view of the program;

This bu on leads you to the search func on vehicle models and the related remote control

programming (see sec on "Search your vehicle model");

This bu on leads you to the program conﬁ gura on func on (see sec on "Program Conﬁ gu-

ra on”);

This bu on leads you to SMART remote programmer device informa on (see sec on “In-

forma on”);

This bu on leads you to programming history display func on (see sec on “Historic

Report”);

This bu on leads you to measuring remote control frequency;

This bu on leads you to close the program;

SMART Remote Programmer

English

9Copyright Silca S.p.A 2017

SEARCH YOU VEHICLE MODEL

This page allows you to search your car model whose remote control need to be preset:

This page includes 3 Areas:

Area 1: display ﬁ lters input area applied to this list in Area 2;

Area 2: Informa on display area that meets ﬁ lters entered in area1.

Area 3: commands area associated with this page.

In area 1 some informa on is available to be entered to search models, that will be displayed in area 2

Area 1 - there are the following ﬁ lters:

- Brand: car brand list in the database;

- Model: car model list for the selected brand;

- Year: reference year of the selected car model;

- Area: car models reference area se ng to be displayed (you can ﬁ nd the default value ﬁ eld se ngs in the

“Program Conﬁ gura on” page;

- Chassis code: chassis reference number;

- FCC: FCC cer ﬁ ca on reference ID of the original remote control;

- Number of bu ons: the number of bu ons available in the original remote control;

- Key proﬁ le: ILCO/SILCA key ar cle used in car models;

- Transponder: type of transponder used in car models;

- Frequency: transmission frequency used by the original remote control;

- Modula on: Transmission modula on used by the original remote control;

The list available in

area 2 contains informa on about models that meets ﬁ lters entered in Area 1; the list with

all models will contain the following columns:

Brand: vehicle brand;

Model: vehicle model;

Year: informa on validity start date of the vehicle model;

Year: informa on validity end date of the vehicle model;

Area: vehicle model reference area (America, Asia, Europe);

Frequency: reference frequency of the original remote control;

Number of bu ons: the number of bu ons available in the remote control;

Remote Control Reference: ILCO/SILCA remote control code

SMART Remote Programmer

English

By selec ng, with the mouse, the line rela ng to a model, some addi onal informa on about it will appear,

such as:

-Vehicle informa on (Brand, Model; Term of validity; Geographical area; Chassis Code)

-Original remote control informa on (Frequency, number of bu ons; bu ons func on; Image)

-ILCO/SILCA remote control informa on (Remote control code; Number of bu ons; Type;Transponder to be

used for programming and/or cloning; setup code to be used for mechanical duplica on )

Addi onal notes:

The bu on func ons shown below are also available:

This bu on applies ﬁ lters entered in Area 1 to display items in Area 2;

This bu on resets all the ﬁ lter values in the area 1;

This bu on leads to start the programming stage of the remote control according to the

selected row in Area 2;

Bu on for viewing a blow-up of the radio control image or technical drawing;

This bu on allows you to view the manual procedure;

Icon indica ng that the radio control or transponder can be programmed with the diagnos c

device

Icon indica ng that the radio control/transponder is programmed automa cally

Icon indica ng that the radio control or transponder CANNOT be programmed with the di-

agnos c device

Icon indica ng that a request can be made for the manual procedure to be used to

programme the radio control

Icon indica ng that the radio control/transponder can be programmed.

See IQ (Info Quest) for conﬁ rma on

Note: please do not move the remote control during programming.

SMART Remote Programmer

English

11Copyright Silca S.p.A 2017

REMOTE CONTROL PROGRAMMING

By pressing the bu on from the “vehicle model search” page we proceed to the remote control pro-

gramming for the selected model, and the following page will appear.

To proceed to place the remote control in the device area, as shown in the image below:

and press any bu on on the remote control.

SMART Remote Programmer

English

Detec ng remote control, the program will automa cally start the programming procedure, and the

following page will appear:

Upon comple on of the procedure, a message will appear indica ng that the process is complete, and the

remote control will be enabled for the next vehicle programming.

By pressing the bu on

on the page the opera on is cancelled, and the program goes back to the

previous page.

SMART Remote Programmer

English

13Copyright Silca S.p.A 2017

INFORMATION

Device informa on is available on these pages:

Window 1: In the event that the device is not connected, we recommend connec ng it to your PC and update

the status of the connec on using

bu on;

Once the devices is connected, appears:

Window 2:

“RegistraƟ on status”: shows whether the device is registered.

“About the device”: contains all the informa on about the device.

- So ware Guide: bu on for direct access to the so ware guide;

- News: bu on for access to the news, if available.

- Serial number: connected device serial number;

- Firmware: ﬁ rmware version installed on your device;

- Database: database version inside your device;

- So ware: SRP program version installed;

Note: if no data is displayed, please make sure the device is connected to PC via USB.

In Area 1, three Update bu ons are available to allow you upgrading ﬁ rmware of your device and upda ng

program database, and the program itself, with the latest version available online.

In Area 2 , a bu on is available: Send log, enables you to send a log-ﬁ le to the remote server.

SMART Remote Programmer

English

HISTORIC REPORT

On this page you can consult the programming history performed by the user on a pc.

Area 1: display ﬁ lters input area applied to this list in Area 2;

Area 2: Informa on display area that meets ﬁ lters entered in area1.

In area 1 the following items are available:

- Brand: car brands list;

- Model: car model list for the selected brand;

- Clear

: this bu on resets the entered ﬁ lters.

Depending on the values entered in area 1, model mee ng ﬁ lters will be displayed in area 2.

In area 2, a list with the following informa on is available:

- Brand: vehicle brand;

- Model: vehicle model;

- Year: informa on validity start date of the vehicle model;

- Year: informa on validity end date of the vehicle model;

- Area: vehicle model reference area (America, Asia, Europe);

- Number: number of programmed remote controls.

Double click on the chosen row to view the ‘prese ng’ window :

SMART Remote Programmer

English

15Copyright Silca S.p.A 2017

REPLACING / INSERTING BATTERIES

Li the ba ery housing cover (Fig. 6). Remove the exhausted ba eries and ﬁ t four new 1.5V alkaline ba eries

(AA), taking care to posi on the poles properly. Replace and close the cover.

WARNING: DANGER OF EXPLOSION IF THE BATTERY IS REPLACED WITH ONE OF THE WRONG TYPE

WASTE DISPOSAL

INFORMATION FOR USERS OF PROFESSIONAL EQUIPMENT

From “Actua on of Direc ve 2012/19/EU regarding Waste Electrical and Electronic Equipment (WEEE)”

The symbol of a crossed waste bin found on equipment or its packing indicates that at the end of the product’s

useful life it must be collected separately from other waste so that it can be properly treated and recycled .

In par cular, separate collec on of this professional equipment when no longer in use is organised and

managed :

a. directly by the user when the equipment was placed on the market before 31 December 2010 and

the user personally decides to eliminate it without replacing it with new equivalent equipment

designed for the same use

b. by the manufacturer, that is to say the subject which was the ﬁ rst to introduce and market new

equipment that replaces previous equipment, when the user decides to eliminate equipment

placed on the market before 31 December 2010 at the end of its useful life and replace it with an

equivalent product designed for the same use. In this la er case the user may ask the manufacturer

to collect the exis ng equipment;

c. by the manufacturer, that is to say the subject which was the ﬁ rst to introduce and market new

equipment that replaces previous equipment, if it was placed on the market a er 31 December

2010 ;

With reference to portable ba eries/accumulators, when such products are no longer in use the user shall

take them to suitable authorised waste treatment facili es.

Suitable separate collec on for the purpose of forwarding discarded equipment and ba eries/accumulators

for recycling, treatment or disposal in an environmentally friendly way helps to avoid possible nega ve eﬀ ects

on the environment and human health and encourages re-use and/or recycling of the materials making up

the equipment.

To remove ba eries/accumulators, consult the manufacturer’s speciﬁ c instruc ons: (see relevant chapter in

the users’ manual).

The sanc ons currently provided for by law shall apply to users who dispose of equipment, ba eries and

accumulators in unauthorised ways .

SMART Remote Programmer

English

FCC/IC INFORMATION

This device complies with Part 15 of the FCC Rules. Opera on is subject to the following two condi ons:

(1) This device not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired opera on. Changes or modiﬁ ca ons on not expressly

approved by the party responsible for compliance could void the user’s authority to operate the equipment.

“This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protec on against harmful inter-

ference in a residen al installa on. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instruc ons, may cause harmful interference to radio

communica ons. However, there is no guarantee that interference will not occur in a par cular installa on.

If this equipment does cause harmful interference to radio or television recep on, which can be determined

by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separa on between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀ erent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.”

ID FCC: 2AHH9-IRKEP1

Silca Smart Software Manual

Marca: Silca

Modello: Smart

Tipo: Software Manual

Scarica PDF

rapporto

in altre lingue

English: Silca Smart
Deutsch: Silca Smart

Silca Smart Software Manual

Silca Smart Software Manual

in altre lingue

Altri documenti