Griven Parade L3 White Light Manuale del proprietario
- Categoria
- Stroboscopi
- Tipo
- Manuale del proprietario
Parade User Manual
L1 - L2- L3 - L4 Rev. 6.0
Date: 23/09/2023
page 1 of 8
Griven S.r.l. - Via Bulgaria, 16
46042 Castel Goredo
Mantova - Italy
© Copyright Griven 2020 - GRIVEN S.r.l. is continuously
developing and improving all its products.
We reserve the right to change specifications without
prior notification
Tel. +39.0376.779483
E-mail: [email protected]
Web: www.griven.com
551091
Parade L1 Parade L2 Parade L3 Parade L4
Code AL5060 - AL5061 (PE) AL5065 - AL5066 (PE) AL5070 - AL5071 (PE) AL5075 - AL5076 (PE)
Power consumption
Consumo di energia
20W (RN) 19W (DW)
19W (W)
38W (RN) 38W (DW)
37W (W)
58W (RN) 57W (DW)
56W (W)
79W (RN) 76W (DW)
75W (W)
Nominal current
Corrente nominale 0.1A (RN) 0.1A (DW)
0.1A (W) @230Vac
0.17A (RN) 0.17A (DW)
0.17A (W) @230Vac
0.26A (RN) 0.26A (DW)
0.25A (W) @230Vac
0.35A (RN) 0.34A (DW)
0.34A (W) @230Vac
Power supply
Alimentazione elettrica 220-240VAC 50/60Hz
Inrush current
Corrente di spunto 23.42 A @240VAC, 25°C 27.5 A @240VAC, 25°C
Power factor
Fattore di potenza cos.φ= 0.87 cos.φ= 0.94 cos.φ= 0.95 cos.φ= 0.97
Electrical class
Classe elettrica I
Weight / Peso 2.1 Kg 3.1 Kg 4.4 Kg 5.6 Kg
Operating temperature
Temp. funzionamento -40°C to +50°C ( -40°F to 122°F )
IP rating / Grado IP IP67
IK rating / Grado IK IK09 IK10 IK09 IK10
914 mm [36”]
70 mm
1219 mm [48”]
610 mm [24”]
318 mm
70 mm
76 mm
[12.5”]
[2.7”]
[3”]
[2.7”]
Parade L1
Parade L2
Parade L3
Parade L4
Dimensions / Dimensioni
Parade L - Rev. 6.0
page 2 of 8
Important notices - Avvisi importanti
- This product must be installed in accordance with applicable national and local
electrical and construction codes by a person familiar with the construction and
operation of the product and the hazards involved. Failure to comply with the
following installation instructions may result in death or serious injury.
- Do not stare at the operating light source.
- The fi xture might be damaged by excess voltage. The installation of an overvolta-
ge protection device on the electrical system (SPD) is recommended for
reduce the risk of damage.
- The use of an adequate magnetothermic switch along the power supply line is
recommended.
-Connect the fi xtures to each other only when disconnected from mains.
- Never leave cables and connectors unconnected or unprotected for long periods.
- Disconnect power before installing or servicing to avoid electrical shock.
- Disconnect power before any connection operation.
- Check voltage and frequency before powering the fi xture. Do not exceed fi xture
specifi ed voltage.
- Do not handle the unit with wet hands or in wet environments.
- Apply to qualifi ed staff for any maintenance service not described in this instruc-
tions manual.
- Do not exceed the maximum quantity of fi xtures per line in order to avoid power
surges.
- Before powering the unit, ensure to use cables and connectors with proper
section and length, according to its power consumption.
- Fix the projector by using screws, hooks or other adequate supports that can
bear its weight.
- If the external fl exible cable of this appliance is damaged, it must only be repla-
ced by the manufacturer, its assistance service or equivalent qualifi ed personnel in
order to avoid hazards.
- Integrated temperature control, the projector reduces power when Ta >35°C.
- The luminaire should be positioned so that prolonged observation of the luminaire
at a distance of less than 2 meters (6.56 ft) is not expected.
- Questo prodotto deve essere installato secondo le normative locali, da personale
specializzato. La mancata osservanza delle istruzioni di installazione può portare
a situazioni di pericolo all’incolumità della persone.
- Non fi ssare la sorgente luminosa durante il suo funzionamento.
- Apparecchiatura sensibile alle sovratensioni. Si consiglia l’installazione di un
dispositivo di protezione delle sovratensioni (SPD) sull’impianto elettrico per
attenuare l’intensità di questi fenomeni proteggendo gli apparecchi dal rischio che
vengano danneggiati.
- E’ consigliato l’uso di un adeguato interruttore magnetotermico/differenziale sulla
linea di alimentazione.
- Collegare tra loro i proiettori solo quando nessuno di essi è collegato alla rete
elettrica.
- Non lasciare mai per lungo tempo agli agenti atmosferici cavi e connettori non
collegati o non protetti.
- Togliere l’alimentazione prima di effettuare qualsiasi operazione all’interno
dell’apparecchiatura.
- Togliere l’alimentazione prima di effettuare qualsiasi operazione di connessione
tra gli apparecchi.
- Prima di connettere l’apparecchio alla rete elettrica, verifi cate la compatibilità di
tensione e frequenza.
- Non maneggiate il prodotto con mani bagnate o in presenza di acqua.
- Rivolgersi ad un tecnico qualifi cato per qualsiasi operazione di manutenzione
ordinaria non descritta nel presente manuale.
- Non superare il numero massimo specifi cato di apparecchi per linea per evitare
pericolori sovraccarichi di corrente.
- Prima di effettuare le connessioni verifi care la portata dei cavi / connettori e la
lunghezza dei cavi tenendo conto dell’assorbimento del prodotto.
- Fissare il proiettore con viti, ganci o altri supporti in grado di sostenerne il peso.
- Se il cavo fl essibile esterno di questo apparecchio vienne danneggiato, deve
essere sostituito esclusivamente dal produttore, dal suo servizio di assistenza o da
personale qualifi cato equivalente, al fi ne di evitare pericoli.
- Controllo della temperatura integrato, il proiettore reduce la potenza ad una
Ta >35°C
- l’apparecchio di illuminazione dovrebbe essere posizionato in modo che non sia
prevista un’osservazione prolungata dell’apparecchio ad una distanza inferiore a
2 metri.
CAUTION: Prolonged staring at the LED source should be
avoided by placing the xture in a proper position.
ATTENZIONE! Fissare la sorgente LED per un periodo prolungato va
evitato posizionando l’apparecchio nella posizione appropriata.
WARNING ! Fixing and connecting operations must
mandatorily be carried out by qualied personnel only !
ATTENZIONE ! Le operazioni di ssaggio e collegamento
devono essere eseguite solo e obbligatoriamente da perso-
nale qualicato!
WARNING ! Make sure that power supply is o before
connecting or disconnecting xtures !
ATTENZIONE ! Assicurarsi che l’alimentazione sia spenta
prima di collegare o scollegare i dispositivi!
Replaceable control gear by a professional Alimentatore sostituibile da un professionista
Replaceable (LED only) light source by a professional Sorgente luminosa (solo LED) sostituibile da un
professionista
La possibilità di riutilizzare alcune parti elettriche del disposi-
tivo è subordinata alla totale responsabilità dell’utilizzatore.
Nell’etichetta è stato riportato il simbolo indicato nel D.lgs n.49
del 14 Marzo 2014 che recepisce la direttiva 2012/19/UE, il quale
indica la necessità di smaltire il prodotto nei riuti dierenzia-
ti, nello specico nei riuti di tipo elettrico ed elettronico. Fare
riferimento al centro di raccolta riuti situato nella Vostra zona.
The possibility of reusing some electrical parts of the devi-
ce is subject to the total responsibility of the user. The la-
bel shows the symbol indicated in Legislative Decree n.49
of 14 March 2014 which transposes Directive 2012/19 / EU,
which indicates the need to dispose of the product in sepa-
rate waste, specically in electrical waste. and electronic.
Refer to the waste collection center located in your area.
This product contains a light source of energy eciency
class:
Questo prodotto contiene una sorgente luminosa di classe
di ecienza energetica:
3000K 4000K Dynamic White RGBW 4000K
F F E F
Parade L - Rev. 6.0
page 3 of 8
“C” Type cable ( Hybrid cable + connectors )
POWER + DMX IN
POWER + DMX OUT
A=DMX-
B=DMX+
C=common
1=N
2=L
3=GND
“M” Type cable (Hybrid cable without connectors - DMX)
POWER + DMX IN
POWER + DMX OUT
Blue= N (Neutral)
Brown=L (Line)
Yellow/Green=GND
RED= DMX +
BLACK= DMX -
WHITE=COMMON
Blue= N (Neutral)
Brown=L (Line)
Yellow/Green=GND
RED= DMX +
BLACK= DMX -
WHITE=COMMON
POWER + DMX IN/OUT
POWER + DMX IN/OUT
“M” Type cable ( Hybrid cable without connectors - DALI) Blue= N (Neutral)
Brown=L (Line)
Yellow/Green=GND
GREY= DALI +
BLACK= DALI -
Blue= N (Neutral)
Brown=L (Line)
Yellow/Green=GND
GREY= DALI +
BLACK= DALI -
POWER + DALI OUT
POWER + DALI IN
Connection - Connessione
Parade L - Rev. 6.0
page 4 of 8
30
Ø6
-90°
+90°
Size 8 (ISO)
socked Hex key
Size 10 (ISO)
Hex key
Size 10 (ISO)
Hex key
Size 4 (ISO)
Allen key
This side to the wall
L1 = from 90 to 319
L2 = from 90 to 610
L3 = from 90 to 915
L4 = from 90 to 1220
The POLAR Edition is tted with a thermal glass which is particularly useful for outdoor applications.
In fact, by warming up, the glass melts ice and snow which might interfere with the projection.
When the projector is on, if required by the weather conditions, the glass is automatically warmed up.
WARNING: If the projection is to be started at a denite time, take care to defrost the glass in
advance so that the LEDs can be lit at the time required.
WARNING: At very low temperatures (below -20° C), it is recommended to let the xture always
powered and to switch on the LEDs when needed.
Polar features (only on Polar Edition xtures )
AB
For 3G applications, consider
the distances informed bellow:
Parade L-1 (A= 8cm, B= 8cm)
Parade L-2 (A= 15cm, B= 15cm)
Parade L-3 (A= 22,5cm , B= 22,5cm)
Parade L-4 (A= 30cm , B= 30cm)
Installation - Installazione
Parade L - Rev. 6.0
page 5 of 8
¹ WARNING ! In this mode, no other DMX control device must be present along the line.
² Only on wireless xtures
The xture must be congured only by using AL1321 IR remote control ( sold separately ) or via any
DMX-RDM compatible controller.
LOGIN
DMX MODE
DMX MODE SETTING
DMX ADDRESS SETTING
Enter the“IR” value on DMX chart
under “MODE” column ( eg: IR=4,
press button 4 ).
001~512 = OK
FLASH
FLASH FLASH FLASH
= OK
FLASH FLASH
= OK
MASTER/SLAVE
AUTOMATIC
MODE
TO BE USED ONLY
WITH DMX MODE #
1
AUTOMATIC/MASTER
5”→10”→20”→ 40”
40”→ 20”→ 10”→ 5”
001
SLAVE FIXTURE SETTING
= OK
FLASH FLASH FLASH
FLASH
2
xFLASH
3
xFLASH
4
xFLASH
4
xFLASH
3
xFLASH
2
xFLASH
FLASH
FIXED
COLOR
MODE
(RGB-RGBW-DW)
TO BE USED ONLY
WITH DMX MODE #1
1 = RED
2= GREEN
3 = BLUE
DIMMER
MODE
(Monochromatic)
TO BE USED ONLY
WITH DMX MODE #1
0%→100%
100%→0%
5’ inactivity = Automatic
LOGOUT
Green-Cyan-Blue-Magenta-
Red-Yellow-White.
4 = COLD WHITE
5 = WARM WHITE
RGBWRGB
DW
LOGOUT OK
RESET OK Reset to default settings
1 = RED
2= GREEN
3 = BLUE
4 = WHITE
WIRELESS
1 = Unlink
2= LED wireless status ON
3= LED wireless status OFF
¹
²
IR Remote Control operations / Operazioni del telecomando IR
Parade L - Rev. 6.0
page 6 of 8
When operating in DMX mode the xture can accept the
following RDM commands:
• Discovery: Upon request of the RDM controller, the xture
signals its own presence (the RDM controller will display
the xture on a list).
• DMX address reading and setting.
• Channels number reading and setting.
• On / O identication: This command is used to identify the
xture you want to get access to (the identication happens
by switching on all the LEDs at full intensity).
• Manufacturer: it displays the name of the manufacturer
(Griven).
• Model description: it displays the xture’s model.
• Software version description: it displays the current version
of the rmware.
• Temperature: it displays the LEDs operating temperature
value.
DMX Chart
RDM functions
Mode Channel Function Value
#1
IR=4
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
#2
IR=5
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
5 0→100% Dimmer 0-255
#3
IR=6
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
5
0% Dimmer 0-5
100-0% Dimmer 6-250
100% Dimmer 251-255
6
No Strobo 0-5
0-100% Strobo 6-250
100% Strobo 251-255
#4
IR=7
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
5
NO FUNCTION 0-5
2700K 6-7
2700K→3000K 8-40
3000K 41-42
3000K→3500K 43-75
3500K 76-77
3500K→4000K 78-110
4000K 111-112
4000K→4500K 113-145
4500K 146-147
4500K→5000K 148-179
5000K 180-181
5000K→5500K 182-214
5500K 215-216
5500K→6000K 217-249
6000K 250-255
6 0→100% Dimmer 0-255
#5
IR=8
1 0-100% Red 0-255
20-100% Red ne 0-255
3 0-100% Green 0-255
40-100% Green ne 0-255
5 0-100% Blue 0-255
60-100% Blue ne 0-255
70-100% White 0-255
80-100% White ne 0-255
RGBW
DW (Dynamic White)
Mode Channel Function Value
#1
IR=2
(Default)
10%→100% Warm white 0-255
20%→100% Cold White 0-255
#2
IR=3
10%→100% Warm white 0-255
20%→100% Cold white 0-255
3 0%→100% dimmer 0-255
#3
IR=3
1 0%→100% Warm white 0-255
2 0%→100% Warm white ne 0-255
30%→100% Cold white 0-255
40%→100% Cold White ne 0-255
Note: in absence of DMX signal the LEDs will remain ON.
Channel Function Value
1 0%→100% dimmer 0-255
Note: in absence of DMX signal the LEDs will remain ON.
Monochromatic version
Mode Channel Function Value
#6
IR=9
(Default)
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% Calibrated White
( Aects RGB channels ) 0-255
Note: in absence of DMX signal the LEDs will remain OFF.
Nelle versioni “Indipendent pixels” le funzioni citate nelle preceden-
ti tabelle vengono ripetute per il numero di moduli dell’apparec-
chio. Es. Parade L3 RGBW nella modalità #1 impegna 12 canali.
In the “Independent pixels” versions, the functions mentioned in
the previous tables are repeated for the number of modules in the
device. E.g. Parade L3 RGBW in mode #1 engages 12 channels.
Indipendent pixels
Parade L - Rev. 6.0
page 7 of 8
Command # Description
1 O
2 Up (Fade rate)
3 Down (Fade rate)
4 Step Up ( Increment arc power level )
5 Step Down ( Decrement arc power level )
6 Recall MAX level
7 Recall MIN level
8 Step down and o ( Decrement arc power level if at min level turn down )
16...31 Go to scene 0...15
32 Reset ( DALI factory default parameters )
33 Store actual level in the DTR
42 Store DTR as MAX level
43 Store DTR as MIN level
45 Store DTR as Power On level
46 Store DTR as Fade Time
47 Store DTR as Fade Rate
64-79 Store DTR as Scene 0...15
80-95 Remove from Scene 0...15
96...111 Add to Group 0...15
112...127 Remove from Group 0...15
128 Store DTR as Short Address
144 Query Status
145 Query Ballast
151 Query Version Number
152 Query Content DTR
153 Query Device Type
154 Query Physical Minimum Level
155 Query Power Failure
160 Query Actual Level
161 Query Max level
162 Query Min level
163 Query Power On level
164 Query System Failure level
165 Query Fade Time/Fade Rate
176...191 Query Scene level
192 Query Groups 0...7
193 Query Groups 8...15
194 Query Random Address High
195 Query Random Address Middle
196 Query Random Address Low
DALI supported commands
DALI version: 1, Device Type: 6(LED), Physical Min Level: 1 (0.1%)
Parade L - Rev. 6.0
page 8 of 8
DMX Mode
Master-Slave / Automatic / Fixed color Mode
Master Addr. 001 Addr. 001
Example with xtures set at 4 DMX channels
Addr. 001 Addr. 005 Addr. ###
B
Power input
DMX
Power input
AL5169
AL5169
C
A
BD
EF
A
B
B
A
C
C
A
A
F
F
G
H
C
I
I
dmx
dmx
dmx
Copyright © 2020, GRIVEN S.r.l World Lighting Challenge - www.griven.com
Parade L-1 L-2 L-3 L-4 Codes: AL5060 AL5061 AL5065 AL5066
AL5070 AL5071 AL5075 AL5076
Rev. A-01
A - Power Input CE ver. 220-240 Vac - ver. 120 & 277 Vac
B - DMX/RDM Controller
C - Start Line Box - AL5058C with connectors / AL5058M without connectors
D - Parade L-1 , L-2 , L-3 , L-4 , L-2 Recessed , L-3 Recessed
E - Connection Cable - AL8264 L=1m AL8265 L=2m AL8266 L=3m AL8267 L=5m AL8268 L=10m
F - DMX Terminator - AL5169
G - Repower Box - AL5167C with connectos / AL5167M without connectors
H - DMX Junction Box - AL5059C with connectors / AL5059M without connectors
I - DMX Cable - AL0512
CE Colours
Brown
Blue
Yellow/Green
Red
Black
White
USE
Live
Neutral
Ground
DMX Data +
DMX Data -
DMX GND
Max. 10 A
per
daisy chain
Use a DMX repeater on each 32nd
the total DMX LINE length exceeds
1000 ft (300m)
Max. 10 A
per
daisy chain
Use a DMX repeater on each 32nd
the total DMX LINE length exceeds
1000 ft (300m)
( Only DMX Mode #1 )
Conguration examples / Esempi di congurazioni
Operating modes / Modalità operative
WARNING ! in this mode, no DMX control device must be present along the line.
ATTENZIONE ! in questa modalità non deve essere presente lungo la linea nessun altro dispositivo di controllo DMX.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Griven Parade L3 White Light Manuale del proprietario
- Categoria
- Stroboscopi
- Tipo
- Manuale del proprietario
in altre lingue
Documenti correlati
-
Griven Parade L3 Recessed Dynamic White Manuale del proprietario
-
-
-
-
-
-
Griven Moon wall Dynamic White Manuale del proprietario
-
-
-
