Blackmagic Desktop Video Manuale utente

Desktop Video

DeckLink

UltraStudio

Intensity

September 2023

Installation and Operation Manual

Languages

To go directly to your preferred language, simply click on the hyperlinks listed in the

contents below.

English 3

日本語 80

Français 158

Deutsch 236

Español 315

中文 393

한국어 471

Русский 549

Italiano 627

Português 705

Türkçe 783

Welcome

We hope you share our dream for the television industry to become a truly creative industry by

allowing anyone to have access to the highest quality video.

Previously, high end television and post production required investment in millions of dollars of

hardware, however with Blackmagic Design video hardware, even Ultra HD 60p is now easily

affordable. We hope you get years of use from your new UltraStudio, DeckLink or Intensity and

have fun working with some of the world’s hottest television and design software!

This instruction manual should contain all the information you’ll need on installing your

Blackmagic Design video hardware. If you’re installing a PCI Express card, it’s always a good

idea to ask a technical assistant for help if you have not installed hardware cards into computers

before. As Blackmagic Design video hardware uses uncompressed video and the data rates

are quite high, you’ll need fast disk storage and a high end computer.

We think it should take you approximately 10 minutes to complete installation. Before you install

Blackmagic Design video hardware, please check our website at www.blackmagicdesign.com

and click the support page to download the latest updates to this manual and Desktop

Video driver software. Lastly, please register your Blackmagic Design video hardware when

downloading software updates. We would love to keep you updated on new software updates

and new features. Perhaps you can even send us your latest show reel of work completed

on your Blackmagic Design video hardware and any suggestions for improvements to the

software. We are constantly working on new features and improvements, so we would love to

hear from you!

Grant Petty

CEO Blackmagic Design

English

Contents

Getting Started 5

Introduction to Desktop Video 5

System Requirements 5

Connecting Power 5

Connecting Video Hardware 6

Installing the Desktop Video Software 10

Capturing and Playing Back Video 15

Blackmagic Desktop Video Setup 16

Introducing Blackmagic Desktop

Video Setup 16

Video Settings 17

Connector Mapping for DeckLink

Quad 2 22

Audio Settings 23

Conversions Settings 25

Setup 27

About 28

Teranex Mini Smart Panel 29

Attaching a Teranex Mini Smart Panel 29

Smart Panel Features 30

Using UltraStudio 4K Mini’s

Front Control Panel 31

Blackmagic Universal Rack Shelf 32

Contents 32

Mounting a Unit to the Rack Shelf 33

Attaching the 1/6 Blanking Panel 33

Attaching the Side 1/3 Width

Blanking Panel 33

DaVinci Resolve 34

Live Grading with DaVinci Resolve 34

Editing with DaVinci Resolve 35

Using your Favorite 3rd Party Software 36

Adobe After Eects CC 36

Adobe Photoshop CC 38

Adobe Premiere Pro CC 39

Adobe Character Animator CC 45

Final Cut Pro 46

Avid Media Composer 49

Blackmagic Media Express 56

What is Blackmagic Media Express? 56

Capturing Video and Audio Files 56

Playing back Video and Audio Files 61

Browsing Media 63

Editing Video and Audio Files to Tape 66

Capturing H.265 Video 67

H.265 Hardware Encoder 68

Capturing H.265 Video with

UltraStudio 4K Extreme 68

Blackmagic Disk Speed Test 69

Removing the Mezzanine Card

from DeckLink 4K Extreme 12G 72

Recovering a DeckLink Card

from an Interrupted Update 73

Help 75

Developer Information 76

Regulatory Notices 77

Safety Information 78

Warranty 79

4Desktop Video

Getting Started

Introduction to Desktop Video

This manual takes you through computer system requirements and installation instructions

for Blackmagic Design’s Desktop Video hardware and software, and how to use them with your

favorite third party software.

The software includes drivers, plugins and applications like the Blackmagic Desktop

Video Setup, and Blackmagic Media Express for fast capture and playback. Blackmagic

Desktop Video software works in conjunction with your UltraStudio, DeckLink, Intensity or

Teranex hardware.

System Requirements

Your computer requires at least 8GB of RAM to efficiently process video.

Mac OS

Blackmagic Desktop Video software runs on the latest versions of Mac OS.

Windows

Desktop Video runs exclusively on 64-bit versions of Windows 10 and 11 with the latest

Windows updates installed.

Linux

Desktop Video runs on 64-bit x86 computers running Linux 3.10 or higher, and on AArch64

computers running Linux 4.9.140 or higher. Please refer to the release notes for the latest list of

supported Linux distributions, package formats and software dependencies.

Connecting Power

If your Desktop Video hardware includes an external power supply, simply connect it to the unit

and switch on the power.

5Getting Started

TIP DeckLink 4K Extreme 12G can also be connected to additional power using

the power adapter cable included with the card. DeckLink 4K Extreme 12G is very

powerfuland we are always looking for ways to provide additional features, such as

mezzanine cards for expanded connectivity. For this purpose, we have included a

power adapter cable so you can plug in additional power if future hardware expansion

on your DeckLink card draws more power than your computer’s PCIe slot can provide.

If you need to supply external power to your DeckLink 4K Extreme 12G you can easily use the supplied

power adapter cable. Simply disconnect the power from your graphics card and plug it into the

adapter cable. The plug willonly connect to one end so there’s no way to connect it incorrectly.

Connecting Video Hardware

There are three types of connectors your Blackmagic Desktop Video hardware may use

toconnect to your computer depending on your model. These connection types include

Thunderbolt, USB 3.0, or PCIe.

Connecting via Thunderbolt

Blackmagic UltraStudio 4K and UltraStudio 4K Extreme feature two Thunderbolt™ 2 ports so

ifyour computer only has a single Thunderbolt port, you can use the additional port to attach

aRAID or other device.

Blackmagic UltraStudio 4K Extreme 3 has two Thunderbolt™ 3 ports and UltraStudio HD Mini

has one Thunderbolt 3 port, for up to 40Gb/s data speeds. When connecting via Thunderbolt

3, connect your Blackmagic Desktop Video hardware directly to the Thunderbolt 3 port on your

6Getting Started

computer using a Thunderbolt 3 cable. Connecting to a Thunderbolt 2 port on your computer

via a Thunderbolt 3 to Thunderbolt 2 adapter is not supported on bus-powered products like

UltraStudio HD Mini.

Make sure your computer is Thunderbolt 3 compatible by looking for the

Thunderbolt icon near its USB-C connector, as shown on the right.

Connecting via USB 3.0

Connect a SuperSpeed USB 3.0 cable into the USB 3.0 port on the unit. Plugthe other end of

the cable into your computer’s USB 3.0 port.

HDMI IN Y IN Pb IN Pr IN S-VIDEO IN VIDEO IN L

AUDIO IN

AUDIO OUT

VIDEO OUT

S-VIDEO OUT

Pr OUT

Pb OUT

Y OUT

HDMI OUT

R

Connecting a SuperSpeed USB 3.0 cable to Intensity Shuttle

Connecting via PCIe

Blackmagic Design PCIe cards plug into a PCIe slot in your computer. Check the information

printed on your card’s box to determine the number of PCIe lanes your card requires.

Forexample, depending on your PCIe card, it will require a x1, x4 or x8 PCIe slot.

It’s worth noting that you can insert PCIe cards into higher capacity slots than they require.

Forexample, a x4 lane PCIe card can be inserted into a x16 lane PCIe slot, though not the other

way around.

If you can’t find the information you need on the box, you can find the number of lanes

yourcard requires, plus other helpful information about your card, in the tech specs at

www.blackmagicdesign.com/products

7Getting Started

Install a Blackmagic Design PCIe card in a spare PCIe slot. If your card

includes an HDMI bracket, it can be installed in any spare PCIe mount and

connects to the rear of the card with the supplied HDMI cables.

Please be careful when installing your DeckLink PCIe card

toavoiddamaging delicate components on the card.

If your card includes a breakout cable, simply plug it into your card’s breakout cable connector.

8Getting Started

Connecting UltraStudio 4K Extreme via PCIe

UltraStudio 4K Extreme and UltraStudio 4K Extreme 3 can also connect to your

computer via PCIe using a PCIe adapter card and cable. Both UltraStudio 4K Extreme

and UltraStudio 4K Extreme 3 need to be connected to a PCIe Gen 2 slot in your

computer. The Blackmagic PCIe Cable Kit contains a PCIe cable and the PCIe adapter

card and is available from your nearest Blackmagic Design reseller.

For the original UltraStudio 4K Extreme, you can use either the Blackmagic PCIe Cable

Kit, or purchase a standard PCIe adapter card from your nearest computer store.

UltraStudio 4K Extreme features a PCIe port for connection to an

external PCIe adapter card that is installed in your computer

The PCIe adapter card is inserted into a PCIe Gen 2 slot inside your computer

Connect the other end of the PCIe cable to the

PCIe port located at the back of your computer

9Getting Started

Installing the Desktop Video Software

Applications, Plugins and Drivers

The Blackmagic Design Desktop Video software includes all the drivers, plugins and

applications needed to use your Desktop Video hardware. Below is a list that shows all the

software items that are installed on your computer.

Mac OS Windows Linux

Blackmagic

Desktop Video drivers

Blackmagic

Desktop Video drivers

Blackmagic

Desktop Video drivers

Blackmagic Desktop Video Setup Blackmagic Desktop Video Setup Blackmagic Desktop Video Setup

Blackmagic Design LiveKey Blackmagic Design LiveKey –

Blackmagic Media Express Blackmagic Media Express Blackmagic Media Express

Blackmagic Disk Speed Test Blackmagic Disk Speed Test –

Adobe Premiere Pro CC,

AfterEffects CC, PhotoshopCC

presets and plug-ins

Adobe Premiere Pro CC,

After Effects CC, PhotoshopCC

presets and plug-ins

–

Final Cut Pro plug-ins – –

Avid Media Composer plug-in Avid Media Composer plug-in –

NOTE For Linux, Blackmagic Media Express is only supported on x86-64 systems.

Automatic Updates

After installing the Desktop Video software and once your computer restarts, it will check the

internal software on your Desktop Video hardware. If it doesn’t match the version installed on

your computer, the software will prompt you to update. Click ‘ok’ to start the update and restart

your computer to complete the process.

NOTE If your DeckLink card is not working after an interrupted update, refer to

the section near the end of this manual called ‘recovering a DeckLink card from an

interrupted update’.

The remainder of the Getting Started section will show you the Desktop Video software

installation process for Mac OS, Windows and Linux.

10Getting Started

Mac OS Installation

Make sure you have administrator privileges before installing any software.

1 Download the newest Desktop Video driver installer from

www.blackmagicdesign.com/support

2 Launch the Desktop Video installer.

3 Click the ‘continue’, ‘agree’ and ‘install’ buttons to install the software. If you are installing

Desktop Video for the first time, installation has a few extra steps that are described below.

4 Restart your computer to enable the new software drivers.

Desktop Video Installer for Mac

Installing on Mac OS for the First Time

When installing Desktop Video on a Mac for the first time, you will need to enable your Mac to

use your Desktop Video equipment during the installation process.

1 When instructed, click on ‘open security preferences’ or open ‘system preferences’

and click on ‘security and privacy’.

11Getting Started

2 In the ‘security and privacy’ preferences, click ‘allow’ to enable the Desktop Video software

on your computer.

Click ‘allow’ in the security and privacy preferences to

enablethe Desktop Video software on your computer

3 When instructed to restart, click ‘not now’.

4 Back in Desktop Video Installer, complete the software installation by clicking‘restart’.

Resetting System Security Policy on an M1 Mac

From Desktop Video 12.2 or later, it is no longer necessary to have ‘reduced security’ enabled

as your Mac’s system security policy. If you had ‘reduced security’ set when installing previous

versions of Desktop Video, it is now advisable to reset your M1 Mac’s security policy to

‘fullsecurity’.

To do this, follow these steps:

1 Start the computer by pressing and holding the power button until you see ‘loading startup

options’ displayed.

12Getting Started

2 Click ‘security policy’.

3 Select ‘full security’.

4 Click OK.

5 A notification will appear informing you that your computer is applying the security policy.

When the notification disappears, you can restart your computer normally.

Windows Installation

1 Ensure you have the very latest driver. Visit www.blackmagicdesign.com/support

2 Open the “Desktop Video” folder and launch the “Desktop Video” installer.

3 The drivers will now be installed on your system. An alert will appear: “Do you want to allow

the following program to install software on this computer?” Click ‘yes’ to continue.

4 You will see a dialog bubble saying “found new hardware” and the hardware wizard

will appear. Select “install automatically” and the system will find the required Desktop

Video drivers.

5 After all drivers have been installed, a dialog bubble will appear saying “your new hardware

is ready for use.” Restart your computer to enable the new software drivers.

Desktop Video Installer for Windows

13Getting Started

Linux Installation

1 Download the latest Desktop Video software for Linux from

www.blackmagicdesign.com/support

2 Open the Desktop Video folder and navigate to the packages required for your distribution

and architecture. Note that ‘amd64’ refers to Intel and AMD 64 bit processors. There are

three sets of packages provided:

– The desktopvideo package provides the core drivers and API libraries.

– The desktopvideo-gui package provides the Desktop Video Setup software.

– The mediaexpress package provides a simple capture and playback utility. This is

supported on x86-64 systems only.

3 Double click the packages you wish to install and follow the onscreen instructions. Ifyou

see any messages about missing dependencies, ensure they are installed first and then

rerun the Desktop Video installer.

4 When the installer has finished it is recommended that you restart your computer to

complete the installation process.

If you cannot find a native Desktop Video package for your Linux distribution, or if you prefer

toinstall from a command line, refer to the ReadMe file for detailed installation instructions.

Desktop Video software ready to be installed from the Ubuntu Software Center.

Updates

If you have not installed the setup software, you can check the internal software is up to date

using the BlackmagicFirmwareUpdater command line tool:

# BlackmagicFirmwareUpdater status

A message similar to the following will appear:

0: /dev/blackmagic/io0 [DeckLink SDI 4K] 0x73 OK

1: /dev/blackmagic/io1 [DeckLink 4K Extreme 12G] 0x0A PLEASE_UPDATE

In this case you could update the internal software with the following command:

# BlackmagicFirmwareUpdater update 1

See the ‘man’ page for a more detailed description of the command’s usage. e.g., for more info

on the internal software updater command, type “man BlackmagicFirmwareUpdater”.

That’s all there is to getting started! Now that you have installed your Blackmagic Desktop

Video hardware and software, you can start capturing and playing back video.

14Getting Started

Capturing and Playing Back Video

Once the Desktop Video hardware and software is installed, you can start capturing and

playing back clips straight away. First, plug your video source into the input on your Desktop

Video hardware, then connect a monitor to the output.

A quick way to begin capture and playback is to record a clip in Blackmagic Media Express,

which was installed on your computer when you installed the Desktop Video software.

Setting Up

1 Connect a monitor or TV to the video output of your Blackmagic Design hardware.

2 Connect a video source to the input of your Blackmagic Design hardware.

A B NTSC

PAL

Y

SDI OUT

HDMI OUT

REMOTE

SDI IN

ANALOG VIDEO IN

REF IN

CH 1 CH 2

ANALOG AUDIO IN

B-Y R-Y

SDI OUT

+ 12V

SDI IN

REF IN

TC IN

Ultra Studio HD Mini

URSA Mini Pro

HDTV

Connect a video monitor and source to your Blackmagic Design video hardware.

Testing Video Capture

1 Launch Blackmagic Media Express. Click on the ‘log and capture’ tab. Your input video

format is automatically detected and Media Express sets the project video format to match.

Your video source will appear in the Media Express preview pane.

2 Click ‘capture’ at the bottom of the ‘log and capture’ window to perform the capture test.

Click ‘capture’ again to finish the test. The captured clip is added to the media list on the left

side of Media Express.

15Capturing and Playing Back Video

Click the ‘capture’ button to commence recording.

Testing Video Playback

1 Click on the ‘playback’ tab.

2 Double click the test clip. The video and any present audio will be sent to the monitor

connected to your hardware’s output.

Blackmagic Desktop Video Setup

Introducing Blackmagic Desktop Video Setup

Blackmagic Desktop Video Setup provides a central location for configuring hardware

settings, plus a real time status display showing the video connected to your hardware’s inputs

and outputs.

To launch Blackmagic Desktop Video Setup:

– On Mac OS, click Blackmagic Desktop Video in ‘system preferences’ or you can launch

the utility from your ‘applications’ folder.

– On Windows 10 and 11, click the ‘start’ button>all programs>Blackmagic Design> Desktop

Video and click the Desktop Video Setup application. The Desktop Video setup

software also launches from the Windows 10 and 11 ‘control panel’.

– On Linux, go to ‘applications’ and then ‘sound and video’ and double click the

Blackmagic Desktop Video Setup application.

When you first open Blackmagic Desktop Video Setup, the home page displays your

connected hardware and provides an overview of all video activity on your hardware’s input

and output connections. If you are sending a video signal to your input, it will be automatically

detected and the format will be displayed under the Video Input icon.

If you have multiple Blackmagic capture and playback devices connected, you can cycle

through them by clicking the arrow buttons on the sides of the home page. To configure

settings, simply click on the hardware image, or the settings icon located below the hardware

name. The Desktop Video Setup utility only displays the settings that are relevant to your

selected hardware, so you don’t have to scroll through pages of menus to find the settings

you want.

16Blackmagic Desktop Video Setup

Blackmagic Desktop Video Setup home page

The following pages of this manual will show you how to adjust settings using Blackmagic

Desktop Video Setup.

Blackmagic Desktop Video Setup lets you adjust video and audio

input and output settings, apply up or down conversions during

capture and playback, and provides information about the driver.

Video Settings

Video Input

Click on a connector icon to set the ‘video input’ connection for your Blackmagic Design

hardware. Only the connectors that are built into your hardware will be shown. When a valid

video signal is detected, the input and video format will be displayed on the Blackmagic

Desktop Video Setup home page.

17Blackmagic Desktop Video Setup

Click on an icon to set your video input connection.

Use XLR Timecode

Select this setting to read timecode from the XLR input instead of the SDI stream.

Enable the checkbox to capture timecode from the dedicated XLR input

Analog Video Input Levels

Drag the ‘video’ and ‘chroma’ sliders to adjust the analog video input levels for component

orcomposite video. Dragging the video slider affects the luma gain and the chroma sliders

decrease or increase the color saturation. When using component video, you can adjust the

Cband Cr values independently. Click the ‘link’ icon to connect them if you want to adjust them

simultaneously.

Video Output

Select the video standard and adjust other settings for your video output.

General

Default Video Standard

To use broadcast monitoring with Final Cut Pro, set the output format to match your Final

Cut Pro project.

When Paused

Click to select whether to display a full frame or a single field on the output when paused.

Video Playback

Click to select whether to display a freeze frame or black output when not playing.

During Capture

Click to select whether the video output displays the playback video or input video during

capture. If you select the ‘video output displays playback video’ option, then your selection

in the ‘video playback’ section will dictate what is displayed on your output. If you select

the ‘video output displays input video’ option, then the input video will be displayed on

your outputs.

18Blackmagic Desktop Video Setup

During Playback

Some Desktop Video products are capable of converting Rec. 601 and Rec. 709 video

outputs to Rec. 2020 for TVs and video monitors that may require it. If your Desktop Video

hardware supports this feature, select ‘convert to Rec. 2020’ in the setup utility. Ifyour

video is already using the Rec. 2020 color space, or is displaying correctly, you can leave

this setting set to ‘keep default color gamut’.

Select what to display on the output when paused,

during video playback and during capture

SDI Output

Color Space

Click to select the color space to convert to. Options are 4:4:4 RGB video or Y, Cb, Cr 4:2:2.

3G-SDI Formats

Click to select whether to output 3Gb/s SDI signals as SMPTE Level A direct mapping or to

have 3Gb/s signals sent with Level B mapping.

1080p HD and 2K

Click to select whether 1080p HD and 2K are output as 1080p progressive video,

or as progressive segmented frame video.

Use the SDI Settings to control the output of your SDI video.

SDI Configuration

Select between single link, dual link and quad link for 3G, 6G or 12G-SDI output. Some

professional color grading monitors and projectors only accept high bandwidth signals like

2160p60 or DCI 4K 4:4:4 via quad link. UltraStudio 4K Extreme can output quad link 3G-SDI

and you can also get a Quad SDI add on card for DeckLink 4K Extreme 12G.

Choose whether to output via single link, dual link

orquad link for 3G, 6G and 12G-SDI video signals

19Blackmagic Desktop Video Setup

8K Formats

8K video is played back via quad link SDI and you can choose your desired quad link

output format.

The two options available are:

Square Division Quad Split – The 8K image is distributed as four quadrant 4K images in a

2 x 2 multi view configuration. Each 4K quadrant image is supplied via SDI using a quad link

connection and reconstructed at the destination to form a complete 8K image. This is also

the selection to use if you want to send each output to a separate display to create a video

wall of Ultra HD monitors.

Sample interleave – Alternate pixels from a single 8K image are distributed as four

separate 4K images via quad link SDI, then combined at the destination to form one

complete 8K image. Therefore, an added benefit of this format is the option to use any of

the four outputs as a down converted 4K image.

When using desktop video equipment for 8K playback,

set your desired quad link 8K output format

Set Analog Video Output

If your Blackmagic Design hardware has shared analog video connectors, you can choose

whether to output your video via ‘component’, ‘composite’ or ‘s-video’ by selecting between the

‘analog video output’ options.

HDMI 3D Output

This setting determines the 3D format for your HDMI monitoring.

Top and Bottom

Arranges both left and right eye images vertically with 50% compression.

Frame Packing

Combines left and right eye images into a single frame without compression.

Side by Side

Arranges both left and the right eye images horizontally with 50% compression.

Left Eye

Only the left eye image is displayed.

Line by Line

The left and right eye images are carried on alternate video lines without compression.

Right Eye

Only the right eye image is displayed.

Set your HDMI 3D Output format.

20Blackmagic Desktop Video Setup

La pagina sta caricando ...

Blackmagic Desktop Video Manuale utente

Blackmagic Desktop Video Manuale utente

in altre lingue

Documenti correlati

Altri documenti