Celestron 91531 Manuale utente

INSTRUCTION MANUAL

Model #91531

EQUATORIAL MOUNT AND TRIPOD

2 | ENGLISH

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Polar Align the Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Basic Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Precise Polar Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Motion Range in Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Adjusting the Mount for Very High or Low Latitudes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

AUX Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Autoguide Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

NexStar+ Hand Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Object Catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Slewing to an Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

CGX Main Menu Tree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Appendix A: Upgrading the Firmware in Your Mount and Hand Control . . . . . . . . . . . . . . . . . . . 25

Appendix B: Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Appendix C: PWI Telescope Control Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Celestron Two Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

ENGLISH | 3

Introduction

The CGX-L German Equatorial Mount and Tripod was

designed to support your telescope for both visual

observation and astrophotography. When used correctly,

the CGX-L serves as a steady platform, with accurate

pointing and tracking for your telescope. Please review

these instructions to familiarize yourself with the mount and

to get started.

Warning

• Never look directly at the Sun with the naked eye or

with a telescope (unless you have the proper solar ﬁlter).

Permanent and irreversible eye damage may result.

• Never use your telescope to project an image of the Sun

onto any surface. Internal heat build-up can damage the

telescope and any accessories attached to it.

• Never use an eyepiece solar ﬁlter or a Herschel

wedge. Internal heat build-up inside the telescope can

cause these devices to crack or break, allowing unﬁltered

sunlight to pass through to the eye.

• Never leave the telescope unsupervised. Make sure

an adult who is familiar with the correct operating

procedures is with your telescope at all times, especially

when children are present.

System Requirements

• The CGX-L requires 12 volts of DC power with at

least 3 amperes of current. An AC to 12VDC 5A

power supply is available from Celestron and includes

a threaded barrel connector which is recommended.

Portable 12 volt ﬁeld batteries also make suitable power

supplies. The mount includes a DC power cable with a

cigarette lighter plug.

• The telescope must have a dovetail mounting bar that

is either the CG-5/Vixen or CGE/Losmandy D format.

CGX-L can ﬁt either of these sizes on the dovetail saddle.

• For best performance, the total telescope payload

should not exceed 75 lbs (34 kg), not including

counterweights.

• Windows 7 or 10 for use with the telescope

control software.

• USB cable with the standard A connector when

plugged into the USB port on the mount (for PC

use only).

Parts List

Box 1: 91530-1 CGX-L Equatorial Mount

CGX-L Equatorial Mount Head

8mm Allen Wrench (captive in rear handle of mount head)

Counterweight Shaft and Stop Nut

3 x 8mm socket hex head screws (attaches head to tripod)

12VDC Power Cable

NexStar+ Hand Control

Box 2: CGX-L Tripod

Tripod

Accessory Tray

Tripod Support (threaded onto central column

of tripod)

Nut and Washer

Hand Control Holster

Box 3: Counterweight

10kg (22lbs) Counterweight

4 | ENGLISH

Overview

Figure 1.1 Overview

Leg Height Adjustment Lock Levers

Dovetail Lock Knobs

Carry Handle

DEC Clutch Lock Lever

R.A. Clutch Lock Lever

Counterweight Shaft

Counterweights

Counterweight Stop Nut

Tripod

Hand Control Holster

Accessory Tray

Hand Control

Dovetail Saddle

Aux 1 & Aux 2 Ports for Hand Control and Accessories

Power Input

Altitude Adjustment Knob

Azimuth Adjustment Knobs

Carry Handle

On/Off Switch

See ﬁgure 1.2

Altitude Lock Knobs (One on each side)

AUX 3 and 4, and Autoglider

See ﬁgure 1.3

8 mm Allen Wrench

(Located under carry handle)

ENGLISH | 5

Figure 1.3 Overview

Figure 1.2 Overview

Belt Drive Windows

Autoguide Port

USB Port

Latitude Scale

AUX 3 and 4

Power Input

AUX 1 and 2

Autoguider

USB Port

6 | ENGLISH

Assembly

Unpack all of the contents and follow these steps to

assemble your mount. If you purchased the CGX-L by itself,

the kit includes one 22lbs counterweight. If you purchased

the CGX-L with a large optical tube, more weights may be

included to achieve balance.

Note: The included 8mm Allen wrench is contained under

the rear handle of the mount as shown in Figure 1.1.

Setup the Tripod

1. Stand the tripod upright and pull the tripod legs apart

until each leg is fully extended.

2. Remove the Tripod Support Nut and Washer from

the central column attached to the top of the tripod

(Figure 1.2).

3. Place the accessory tray over the central column so

that each of the three arms of the tray is supporting

a tripod leg.

4. Thread the nut and washer back onto the threaded column

and ﬁrmly tighten into place. The accessory tray should not

be able to move against the tripod.

5. Adjust the height of the tripod by loosening the lock levers

on the end of each tripod leg. Then adjust the leg height

as needed and retighten the lock levers, one leg at a time.

Attach the Mount to the Tripod

1. Place the head onto the tripod so that it seats securely

into the mating surface.

2. For best stability, orient the mount so that the counter-

weight shaft is directly over a tripod leg as shown in

Figures 1.1 and 1.2. Note that you can orient the mount

so the counterweight shaft is between two of the tripod

legs (which can be useful in low latitudes), allowing the

counterweights to have more clearance from the tripod.

3. Using the captive 8mm Allen wrench (Figure 3), tighten

the 3 attachment bolts onto the mount.

Figure 2.1 Tripod setup

Figure 2.2 Tripod setup

Figure 3 Attaching the mount to the tripod

Accessory Tray

Central

Column

Allen

Wrench

Tripod Support

Nut and Washer

Attachment

Bolts

ENGLISH | 7

Roughly Polar Align the Mount

Before more weight is added to the mount and tripod,

roughly position the mount so that it’s pointing north

(or south if in the southern hemisphere), and set to your

latitude. Loosen the two altitude lock knobs and turn the

altitude adjustment knob (Figure 1.1) until you are roughly

set to your latitude indicated on the latitude scale (Figure

1.2), then retighten the altitude lock knobs. The scale is

intended for rough polar alignment only. A more precise

polar alignment can be achieved later with the assistance

of the computerized hand control.

Add the Counterweight(s)

Remove the stop nut at the end of the counterweight shaft,

add the counterweight(s), then thread the stop nut back on.

Keep the Counterweight shaft pointed downward.

Attach the Telescope to the Mount

1. Make sure both R.A. and Dec clutch levers are tightened.

2. Loosen the dovetail saddle lock knobs enough to allow

the dovetail to ﬁt into the saddle. Note the arrow should

be pointing to the same side as the handle labeled

“Celestron” (Figure 4).

3. Slide the telescope’s dovetail bar into the dovetail saddle

of the mount. Tighten the telescope in place with the two

lock knobs (Figure 5).

The CGX-L ﬁts the large Celestron CGE-style dovetail

and the smaller CG-5-style dovetail, also common to the

Losmandy D(1) and Vixen-style(2) dovetail.

1: Test ﬁt your Losmandy dovetail bar before securing your telescope to the mount.

Sizes and dovetail angles across different manufacturers can vary.

2. Test ﬁt your Vixen dovetail bar before securing your telescope to the mount. Be

aware that some of the Vixen-style dovetails are not ﬂat and have different heights

along the bar. Depending on the length of the ﬂat, it can affect the ﬁt onto the

dovetail saddle of the mount.

Balance the Mount

Right Ascension Axis:

Carefully unlock the clutch lever for R.A. and position the

counterweight shaft so that it’s horizontal. Without letting

go of the telescope, check to see which side the balance is

in favor of. Slide the counterweights as needed so the R.A.

axis does not move when the clutch is unlocked.

Declination Axis:

With the counterweight shaft still positioned horizontally,

carefully unlock the clutch lever for Dec and check which

way the optical tube is balanced. Slide the optical tube

forward or backward as needed to achieve balance. For

large and heavy telescopes, return the telescope to the

home position before loosening the dovetail saddle lock

knobs (Figure 6).

Figure 4 Attaching the mount to the tripod

Figure 5 Telescope dovetail securely in place

Figure 6 Balancing the mount

Dovetail

Orientation Arrow

Dovetail

Lock Knobs

8 | ENGLISH

4. Using the direction keys, center the star in the eyepiece of

your telescope and press ALIGN.

5. Select a second star from the list and repeat the process

from steps 2-4. When prompted to add a Calibration Star,

you can either press BACK to complete the alignment, or

for best results, proceed to add a calibration star.

For best results, add at least one Calibration Star. This

will improve the pointing accuracy of your mount.

6. When prompted to “Add Calibration Star”, choose a star

from the list and press ENTER. The mount will slew to the

other side of the meridian to add a calibration star.

7. Center the star in the viewﬁnder and press ENTER, then

center the star in your eyepiece and press ALIGN.

8. When prompted to add another calibration star, you may

continue to add more, or press BACK to complete the

alignment.

Selecting Objects

Select from the object database categorized by Solar

System, Stars, or Deep Sky. Within these menus (on

keypad numbers 1, 2, and 3), you can select by object

name or popular catalog number (such as M42 for

Messier 42).

Keypad 6 and 9 (up and down) allows you to scroll

through any list in the hand control. Press ENTER to go

to the selected object the list.

Example of selecting and slewing to Messier M42 deep

sky object:

• Press DEEP SKY then ENTER

• Scroll down (keypad 9) to Messier and press ENTER

• Press “0-4-2” on the keypad and press ENTER

The SkyTour (keypad 5) is a great way to explore the sky

without consulting a star chart. The Tour function will

generate a list of the most interesting objects to observe

for your time and location.

Figure 8 Polar alignment adjustment

Attach the Hand Control Holster

Wrap the hook & loop strap and holster around the tripod

leg and place the hand control in the holster.

Plug in the Hand Control

Plug the supplied NexStar+ hand control into one of the

Aux ports.

Warning: Do not plug the hand control into the

Autoguide Port. Damage to the mount or hand control

could occur. Similarly, do not plug an autoguider cable

into the Aux port or damage could occur.

Home Position

The mount is in the “home” position when the counterweight

shaft is pointing downward, and the telescope is pointing

along the polar axis of the mount as pictured in (Figure 7).

The mount’s internal switches will take the mount to its

home position when you power it on (more on that in

“Basic Usage”), but you can still manually position it before

powering on the mount. Simply unlock the two lock levers,

and move the telescope to the desired position.

Polar Align the Mount

The computerized go-to is capable of locating objects

even if the mount is not perfectly polar aligned. However,

polar alignment is necessary to achieve the best

tracking accuracy of your mount, and it’s essential to

astrophotography. When polar aligned, an Equatorial mount

tracks the sky in one motion, keeping the object centered in

the eyepiece or camera.

CGX-L’s polar alignment system consists of an altitude

adjuster and azimuth adjuster (Figure 8).

An optional polar alignment scope is available from Celestron

and attaches to the mount. The optional polar axis scope

does not pass through the R.A. axis because that area is used

for internal cabling. If you are not using the optional polar

alignment scope, you can achieve a rough polar alignment

by sighting through the viewﬁnder of your telescope, and

adjusting the mount until you center Polaris in the eyepiece

of your telescope. This will get you to within about three-

quarters of a degree within the North Celestial Pole (NCP).

Basic Usage

With your mount assembled and polar aligned, proceed to

startup the mount:

Powering the Mount

The CGX-L mount can be powered by the supplied car

battery adapter to a 12VDC battery source that can deliver

at least 3 amperes of current. Or you may use an optional

AC adapter that delivers at least 3 amperes of current.

AC power adapters with threaded barrel connectors are

available from Celestron.

Figure 7 Telescope in the home position

Altitude

Adjustment Knobs

Altitude

Lock Knobs

Azimuth

Adjustment Knobs

ENGLISH | 9

Home Position and Site Information

1. Plug the included NexStar+ Hand Control into one of the

Aux ports. You can plug into any of Aux 1 to 4 ports.

2. Plug the power cable into the power input port on the

mount. Be sure to secure the power cable with the

threaded barrel connector.

3. Turn the power switch on.

4. When the hand control displays “CGX-L Ready”, press

ENTER twice. The mount will proceed to move to the

home switch position.

5. Select City Database or Custom Site.

- In City Database, select the nearest city to your location.

- If you choose Custom Site, you will have to enter the

longitude, latitude and time zone of your location.

6. Once the location is selected, proceed to enter the date

and time. The CGX-L has a Real-Time Clock (RTC) which

stores the date, time and location information for the next

time you use the mount.

Alignment

Prerequisite: The mount must be roughly polar aligned,

with the date, time and location information correctly

entered as outlined before this step.

1. For best alignment results, choose Two Star Align and

press ENTER. You can also choose from Solar System,

One Star, Last Align, or Quick Align. The Scroll buttons

6 and 9 on the keypad are used to scroll through any list

selection in the hand control.

2. Select the ﬁrst star from the named star list. Use the

Scroll buttons 6 (up) and 9 (down) on the keypad to scroll

through the star names. They consist of the brightest

and easiest stars to ﬁnd. Press ENTER when you have

selected a suitable star. If your mount is at least roughly

polar aligned, the mount will slew to the approximate

location of the star.

The default selection of stars is on the west side of the

meridian. If your sky is obstructed in the west or you wish

to choose from stars on the east side of the meridian,

press the MENU button on the keypad.

3. Using the direction keys, slew the telescope to the

selected named star and center it in the viewﬁnder of your

telescope, then press ENTER.

The mount will automatically adjust the motor speed for

ﬁne centering.

4. Using the direction keys, center the star in the eyepiece of

your telescope and press ALIGN.

5. Select a second star from the list and repeat the process

from steps 2-4. When prompted to add a Calibration Star,

you can either press BACK to complete the alignment, or

for best results, proceed to add a calibration star.

For best results, add at least one Calibration Star. This

will improve the pointing accuracy of your mount.

6. When prompted to “Add Calibration Star”, choose a star

from the list and press ENTER. The mount will slew to the

other side of the meridian to add a calibration star.

7. Center the star in the viewﬁnder and press ENTER, then

center the star in your eyepiece and press ALIGN.

8. When prompted to add another calibration star, you may

continue to add more, or press BACK to complete the

alignment.

Selecting Objects

Select from the object database categorized by Solar

System, Stars, or Deep Sky. Within these menus (on

keypad numbers 1, 2, and 3), you can select by object

name or popular catalog number (such as M42 for

Messier 42).

Keypad 6 and 9 (up and down) allows you to scroll

through any list in the hand control. Press ENTER to go

to the selected object the list.

Example of selecting and slewing to Messier M42 deep

sky object:

• Press DEEP SKY then ENTER

• Scroll down (keypad 9) to Messier and press ENTER

• Press “0-4-2” on the keypad and press ENTER

The SkyTour (keypad 5) is a great way to explore the sky

without consulting a star chart. The Tour function will

generate a list of the most interesting objects to observe

for your time and location.

Figure 8 Polar alignment adjustment

10 | ENGLISH

Precise Polar Alignment

Celestron’s All-Star Polar Alignment allows you to precisely

polar align your mount without using Polaris or a polar axis

ﬁnder. This software-assisted polar alignment allows you to

choose a convenient star.

Prerequisite: The CGX-L must ﬁrst be aligned with a

Two Star, One Star, or Solar System Align.

1. Select a suitable bright star from the NexStar hand

control’s database. Slew the telescope to the star.

2. Press the ALIGN button. Select “Polar Align” then

“Align Mount” from the list.

3. The telescope will then re-slew to the alignment star

and ask you to center it in the eyepiece in order to

“sync” on the star. Press ENTER, center the star with

the arrow keys, then press ALIGN to sync on the star.

4. Press ENTER and the telescope will slew to the

position that the star should be if it were accurately

polar-aligned. At this point, do not use the hand

control to center the star.

5. Use the mount’s altitude and azimuth adjustments

to center the star in the eyepiece.

6. Press the ALIGN button.

The mount is now precisely polar aligned. You may

proceed to use the mount without a new go to alignment.

Motion Range in Mount

Sofware Range

The CGX-L employs software controlled limit sensors which

detect when the mount has nearly reached its mechanical

range limit. Once the mount reaches the sensor, the motor

will decelerate to a stop and a “Limit Switch” warning

message will appear. The mount will no longer slew in the

direction of the limit switch until you reverse directions.

Mechanical Range

The CGX-L uses internal cabling so the mount is designed

not to move more than a certain range. Both axes are

limited by a hard stop built into the mount. This limited

range can also help prevent unintentional interference

between your telescope and the mount or tripod. If for any

reason the mount exceeds the software limit switch (or if

the clutch is unlocked and the mount is manually moved),

the mount will halt at the hard stop.

R.A. limit (Figure 9.1) allows you to track 20º past the

meridian. If you leave the mount unattended while it’s

tracking, it will automatically stop before reaching the

mechanical hard stop. Dec limit (Figure 9.2) contains

enough slew range to reach any portion of the sky.

Figure 9.1 One side of R.A. mechanical limit

Figure 9.2 One side of DEC mechanical limit

ENGLISH | 11

Adjusting the Mount for Very High or

Low Latitudes

The EQ head can be set on the tripod in three different positions to

optimize the center of balance over the tripod, or to provide more

clearance when needed at lower latitudes. Additionally, the EQ head can

be positioned so that the counterweight shaft is directly above a tripod

leg (recommended default), or rotated so that the counterweight shaft is

between two of the tripod legs for additional low latitude clearance.

1. Remove the head from the baseplate by removing the 4 socket-

head screws.

2. Carefully remove the 8 socket head screws located under the head.

Once they are removed, the altitude adjustment mechanism will be the

only thing securing the bottom plate of the EQ head (Figure 10.1).

3. Turn the altitude adjuster knob until the threaded holes on the bottom

of the mount align with the new set of holes on the bottom plate. Shift

the plate forward (towards the counterweight shaft side) if you wish to

use at lower latitudes. Shift the plate backward (towards the altitude

adjustment knob) if you wish to use at higher latitudes (Figure 10.2).

USB Port on the Mount

The USB port on the CGX-L is used to interface with your PC for

use with the dedicated telescope control software. Simply connect a

standard USB B type cable into the USB port on the mount, and plug

into your PC. The mount should automatically install and assign a COM

port to your devices.

The USB port on the mount is not intended to be used with ASCOM or

third party telescope control software. To control the mount via ASCOM,

connect your PC to the NexStar+ hand control’s mini USB port.

Mini USB Port on the NexStar+ Hand Control

The mini USB port on the hand control can be used to connect to your

PC for these purposes:

1. To update the hand control and motor control board ﬁrmware.

2. To interface with third-party software that uses ASCOM.

Aux Ports

Aux 1 and Aux 2 can be used for the NexStar+ hand control, as well as

optional accessories such as the StarSense AutoAlign and SkyPortal

WiFi module.

The CGX-L is equipped with two additional Aux ports located under the

dovetail saddle. You can use any of the same accessories in these Aux

ports. They move with the declination axis of the mount, and depending

on your cable conﬁguration, it can be a convenient location to plug in

your accessories.

Autoguide Ports

The autoguide port should only be used for autoguide camera relays.

CAUTION: Never plug the NexStar+ hand control or other accessory

into the autoguide port. Damage could result.

The CGX-L is equipped with a redundant autoguider port, located next

to Aux 3 and Aux 4 near the dovetail saddle. You can only use one

autoguide port. The redundant port is intended to provide you with the

best option that suits your particular cable conﬁguration.

Figure 10.2 Changing the mount position on the tripod head

DEFAULT POSITION

BACK POSITION

FRONT POSITION

Figure 10.1

Socket Head Screws

Securing Baseplate

Baseplate

12 | ENGLISH

NexStar+ Hand Control

1. Liquid Crystal Display (LCD) Window: Red

backlighting for comfortable nighttime viewing of

telescope information and scrolling text. Remove the

clear protective tape from the screen before use.

2. Align: Instructs the telescope to begin the default alignment

procedure. It is also used to select star or object as an

alignment position.

3. Direction Keys: Allow complete control of your telescope

in any direction. Use the direction keys to center objects in

the eyepiece or to manually slew your telescope.

4. Catalog Keys: Allow direct access to each of the main

catalogs in the database of thousands of objects.

Your telescope contains the following catalogs in its database:

• Solar System- All 7 planets in our Solar System plus

the Moon, Sun and Pluto.

• Stars- Custom lists of all the brightest stars, double

stars, variable stars, constellations and asterisms.

• Deep Sky- Custom lists of all the best Galaxies,

Nebulae and Clusters, as well as the complete

Messier and select NGC objects.

5. Identify: Searches your telescope’s database and

displays the name and offset distances to the nearest

matching objects.

6. Menu: Displays setup and utilities functions, such as

tracking rate, user deﬁned objects and others.

7. Option (Celestron Logo): Works similar to the SHIFT

key on a keyboard and can be used in combination with

other keys to access more advanced features and

functions to be added with later ﬁrmware updates.

8. Enter: Pressing ENTER allows you to select any of your

telescope’s functions, accept entered parameters and

slews the telescope to displayed objects.

9. Back: Pressing BACK will take you out of the current

menu and display the previous level of the menu path.

Press BACK repeatedly to get back to a main menu or

use to erase data entered by mistake.

10. Sky Tour: Activates the tour mode, which seeks out all

of the best objects in the sky and automatically slews

your telescope to those objects.

11. Scroll Keys: Used to scroll UP and DOWN within any of

the menu lists. A double arrow symbol on the right side

of the LCD indicates that the scroll keys can be used to

view additional information. The buttons have an angled

shape to make it easier to locate without looking.

1

9

8

13

4

12

2

3

4

5

6

7

15

11

10

14

12. Motor Speed: Similar to the Rate Button on the original

NexStar hand control, it allows you to change the motor’s

speed when the direction keys are pressed.

13. Object Info: Displays coordinates and valuable

information about objects selected from your

telescope’s database.

14. Mini Usb Port (cable not included): Links to PC

to control telescope with desktop or to perform

ﬁrmware updates.

15. Help Menu: In future ﬁrmware updates, this button will

offer troubleshooting tips. For your convenience, it

currently functions as a shortcut to the Messier Catalog.

Figure 11

14

Figure 11.2

ENGLISH | 13

Selecting an Object

Once the telescope is properly aligned, you can choose

an object from any of the catalogs in the NexStar+ hand

control’s database. The hand control has a key designated

for each category of objects in its database; Solar System

objects, Stars and Deep Sky objects.

• Solar System – The Solar System catalog will display

all of the planets (and Moon) in our solar system that

are currently visible in the sky. To allow the Sun to be

displayed as an option in the database, see Allow Sun

option in the Database Setup section of the manual.

• Stars – The Stars catalog displays custom lists of all

the brightest stars, double (binary) stars, variable stars,

constellations and selected asterisms.

• Deep Sky – The Deep Sky catalog displays a list of all

of the best galaxies, nebulae and clusters, as well as the

complete Messier and select NGC objects. There is also

an alphabetical list of all deep sky objects in order by

their common name.

Use the SCROLL keys to scroll through the catalogs to

ﬁnd the object you wish to view. When scrolling through

a long list of objects, holding down either the UP or

DOWN key will allow you to scroll through the catalog

at a rapid speed.

Slewing to an Object

Once the desired object idisplayed on the hand control

screen, you have two options:

• Press the OBJECT INFO Key. This will give you useful

information about the selected object such as magnitude,

constellation and extended information about the most

popular objects.

- Use the UP/DOWN arrow buttons to scroll through

the displayed object info.

- Use the BACK button to return to the object database.

• Press the ENTER Key. This will automatically slew the

telescope to the coordinates of the object displayed on

the hand control. While the telescope is slewing to the

object, the user can still access many of the hand control

functions (such as displaying information about the object).

NOTE: The Messier, NGC and SAO catalogs require

the user to enter a numeric designation. Once you have

selected the appropriate catalog button and selected the

Messier, NGC or SAO catalog, you will see a ﬂashing

cursor indicating you are in numeric entry mode.

Enter the catalog number for the object you want to view.

Press ENTER to command the telescope to slew to the

object, or hold the OPTION button (the Celestron logo)

and press OBJECT INFO to see information about the

object you selected.

CAUTION: Never slew the telescope when someone is

looking into the eyepiece. The telescope can move at fast

slew speeds and may hit an observer in the eye.

Motor Speed Button

The MOTOR SPEED button, similar to the Rate button on

the original NexStar hand control, allows you to instantly

change the speed rate of the motors from high speed

slew rate to precise guiding rate or anywhere in between.

Each rate corresponds to a number on the hand control

key pad. The number 9 button is the fastest rate

(approximately 3.5° per second, depending on the mount)

and is used for slewing between objects and locating

alignment stars. The number 1 button on the hand

control is the slowest rate (half sidereal) and can be used

for accurate centering of objects in the eyepiece.

To change the speed of the motors:

• Press the MOTOR SPEED key on the hand control.

The LCD will display the current motor speed.

• Press the number on the hand control that corresponds

to the desired speed.

The hand control has a “double button” feature that allows

you to instantly speed up the motors without having to

choose a speed. To use this feature, simply press the arrow

button that corresponds to the direction that you want

to move the telescope. While holding that button down,

press the opposite direction button. This will increase the

speed to the maximum slew rate.

When using the hand control’s up and down direction

buttons, the slower slew rates (6 and lower) move the

motors in the opposite direction than the faster slew rates

(7- 9). This is done so that an object will move in the

appropriate direction when looking into the eyepiece (i.e.

pressing the UP arrow button will move the star upwards

in the ﬁeld of view of the eyepiece). However, if any of the

slower slew rates (rate 6 and below) are used to center

an object in the StarPointer, you may need to press the

opposite directional button to make the telescope move

in the correct direction.

14 | ENGLISH

The Hand Control Menu

The “Hand Control” menu allows you to customize certain

features of the NexStar+ hand control. To access this menu,

press the MENU button (#7 on the keypad) and use the

scroll buttons to select “Hand Control” and press ENTER.

Use the scroll buttons to select from the following options:

• Lights Control: Independently adjust the brightness of the

number keypad and the LCD.

• Scrolling Menu: Adjust how fast words move across the

face of the LCD.

• Toggle Bold Font: Change the format of the font displayed

on the LCD from normal to boldface.

• Set Contrast: Use the scroll keys to adjust the contrast

of the LCD.

• Set Language: Change the displayed language on

the LCD.

NOTE: The Set Language feature may also appear the

ﬁrst time you use your new hand control. You may also

initiate it at any time by holding down the Option button (the

Celestron logo) for 10 seconds while powering up

the telescope.

Alignment Procedures

In order for the telescope to accurately point to objects in the

sky, it must ﬁrst be aligned with known positions (stars) in the

sky. With this information, the telescope can create a model

of the sky, which it uses to locate any object with known

coordinates. There are many ways to align your telescope

with the sky depending on what information the user is able

to provide:

• Two Star Align uses the entered time/location information

and allows the user to select which two alignment stars the

telescope will automatically slew to.

• One Star Align uses the same time/location information

but only uses one star for alignment.

• Solar System Align will display a list of visible

daytime objects (planets and the Moon) available to

align the telescope.

• Quick-Align will ask you to input all the same information

as you would for the Two Star Align procedure. However,

instead of slewing to the alignment stars for centering and

alignment, the telescope bypasses this step and simply

models the sky based on the information given.

• Last Alignment restores your last saved star alignment

and switch position. Last Alignment also serves as a good

safeguard in case the telescope should lose power.

Two Star Align

Two-Star Align allows the user to select two stars on which

to align the telescope. To align your telescope using the

Two-Star Align method:

1. Select Two-Star Align from the alignment choices given.

Based on the date and time information entered, the hand

control will automatically select and display a bright star

that is above the horizon.

• Press ENTER to select this star as your ﬁrst alignment star.

• If for some reason the chosen star is not visible (perhaps

behind a tree or building), press BACK to have the hand

control automatically select the next brightest star.

• Or you can use the Up/Down keys to browse the entire

Named Star list and select any one of over two hundred

alignment stars.

2. Once the telescope is ﬁnished slewing to your ﬁrst

alignment star, the display will ask you to use the arrow

buttons to align the selected star with the cross hairs in

the center of the ﬁnderscope. When centered in the ﬁnder,

press ENTER. The display will then instruct you to center

the star in the ﬁeld of view of the eyepiece. When the star

is entered, press ALIGN to accept this star as your ﬁrst

alignment star.

3. After the ﬁrst alignment star has been entered, the hand

control will automatically select a second alignment star

and have you repeat this procedure for that star. When

the telescope has been aligned on both stars, the display

will ask you if you wish to add additional calibration stars.

Calibration stars are used to improve the pointing

accuracy of your telescope by compensating for subtle

opto-mechanical misalignments between the telescope

optics and the mount. Therefore, it is usually a good idea

to add at least one additional calibration star to improve

the mount’s all-sky pointing accuracy.

4. Press ENTER to select a calibration star. Select a star the

same way you did with the ﬁrst two alignment stars and

press ENTER. You will notice that all the calibration stars

displayed are located on the opposite side of the side of

the sky (Meridian) as the original alignment stars. This is

essential for an accurate calibration of the mount. Finally,

you can choose to continue to add additional calibration

stars or Press BACK to complete the alignment.

Note: East/West Filtering – In order to ensure the best

possible full-sky pointing accuracy, your computerized mount

automatically ﬁlters and chooses its initial alignment stars so

that the ﬁrst two alignment stars are located on one side of

the Meridian and any calibration stars are on the opposite

side of the Meridian, as indicated by the “W” or “E”

displayed in the upper-right corner of the LCD. East/West

ﬁltering can be changed simply by pressing the MENU

button at any time during the alignment process.

ENGLISH | 15

Tips for Adding Calibration Stars:

• Although for casual observing it is not necessary to add

calibration stars, it is recommended that you add as many

as three calibration stars for optimal point accuracy.

• Choosing calibration stars that are near the celestial

equator offer the better results than stars near the

celestial poles.

• Although it is not necessary to use calibration stars if the

telescope mount has not been moved since its original

alignment/calibration, it may be necessary to recalibrate

the telescope if the optical tube has been removed for

any reason.

Note: Meridian – The Meridian is an imaginary line in the

sky that starts at the North celestial pole and ends at the

South celestial pole and passes through the zenith. If you are

facing south, the meridian starts from your Southern horizon

and passes directly overhead to the North celestial pole.

Quick-Align

Quick-Align uses all the date and time information entered at

startup to align the telescope. However, instead of slewing to

the alignment stars for centering and alignment, the telescope

bypasses this step and simply models the sky based on the

information given. This will allow you to roughly slew to the

coordinates of bright objects like the Moon and planets and

provides the telescope with information needed to track

objects in any part of the sky (depending on accuracy of

polar alignment). Quick-Align is not meant to be used to

accurately locate small or faint deep-sky objects or to track

objects accurately for astroimaging.

To use Quick-Align, simply select Quick Align from the

alignment options and press ENTER. The telescope will

automatically use the entered date/time parameters to align

itself with the sky and display Alignment Successful.

Note: Once a Quick-Align has been done, you can use

the Re-alignment feature (see below) to improve your

telescope’s pointing accuracy.

Last Alignment

The Last Alignment method will automatically recall the last

stored index positions to continue using the alignment that

was saved when the telescope was last powered down.

This is a useful feature should your telescope accidentally

lose power or be powered down.

Re-Alignment

The mount has a re-alignment feature which allows you to

replace any of the original alignment stars with a new star or

celestial object. This can be useful in several situations:

• If you are observing over a period of a few hours, you may

notice that your original two alignment stars have drifted

towards the west considerably. (Remember that stars are

moving at a rate of 15° every hour). Aligning on a new star

that is in the eastern part of the sky will improve your pointing

accuracy, especially on objects in that part of the sky.

• If you have aligned your telescope using the Quick-Align

method, you can use Re-Align to align on actual objects

in the sky. This will improve the pointing accuracy of your

telescope without having to re-enter additional information.

• If you have used the computer-assisted polar alignment

method and have manually moved the mount, it may

be necessary to re-align the mount for improved

pointing accuracy.

To replace an existing alignment star with a new alignment star:

1. Select the desired star (or object) from the database and

slew to it.

2. Carefully center the object in the eyepiece.

3. Once centered, press the BACK button until you are at

the main menu.

4. With CGX Ready displayed, press the ALIGN key on

the hand control to select Alignment Stars from the list

of options.

5. The display will then ask you which alignment star you

want to replace. Use the UP and Down scroll keys to

select the alignment star to be replaced. It is usually best

to replace the star closest to the new object. This will

space out your alignment stars across the sky.

6. Press ALIGN to make the change.

16 | ENGLISH

Object Catalog

Selecting an Object

Once the telescope is properly aligned, you can choose

an object from any of the catalogs in the NexStar+ hand

control’s database. The hand control has a key designated

for each category of objects in its database; Solar System

objects, Stars and Deep Sky objects.

• Solar System – The Solar System catalog will display

all the planets (and Moon) in our Solar System that are

currently visible in the sky. To allow the Sun to be displayed

as a selectable object in the database, see the Sun Menu

option in Scope Setup Menu.

• Stars – The Stars catalog displays custom lists of all

the brightest stars, double (binary) stars, variable stars,

constellations and selected asterisms.

• Deep Sky – The Deep Sky catalog displays a list of all

the best galaxies, nebulae and clusters, as well as the

complete Messier and select NGC objects. There is also

an alphabetical list of all deep sky objects in order by their

common name.

Use the scroll keys to scroll through the catalogs to ﬁnd the

object you want to view.

When scrolling through a long list of objects, holding down

either the UP or DOWN key will allow you to scroll through

the catalog rapidly.

Slewing to an Object

Once the desired object is displayed on the hand control

screen, you have two options:

• Press the OBJECT INFO Key. This will give you useful

information about the selected object such as magnitude,

constellation and extended information about the most

popular objects.

• Use the UP/DOWN arrow buttons to scroll through the

displayed object info.

• Use the BACK button to return to the object database.

• Press the ENTER Key. This will automatically slew the

telescope to the coordinates of the object displayed on the

hand control. While the telescope is slewing to the object,

the user can still access many of the hand control functions

(such as displaying information about the object).

NOTE: The Messier, NGC and SAO catalogs require the

user to enter a numeric designation. Once you have

selected the appropriate catalog button and selected the

Messier, NGC or SAO catalog, you will see a ﬂashing

cursor indicating you are in numeric entry mode. Enter the

catalog number for the object you want to view. Press ENTER

to command the telescope to slew to the object or hold the

OPTION button (the Celestron logo) and press OBJECT

INFO to see information about the object you selected.

CAUTION: Never slew the telescope when someone

is looking into the eyepiece. The telescope can

move at fast slew speeds and may hit an observer

in the eye.

SkyTour Button

The CGX-L mount includes a tour feature which allows

you to choose from a list of interesting objects

based on the date and time in which you are observing.

The automatic tour will display only those objects that are

within your set catalog ﬁlters limits. To activate the Tour

feature, press the SKY TOUR key on the hand control.

1. Press the SKY TOUR button on the hand control.

2. Use the SCROLL buttons to select Best of Tonight.

3. The CGX-L mount will automatically slew in azimuth to its

starting position which will help minimize the chance of

wrapping the power cord during the tour.

4. The hand control will display the best objects to observe

that are currently in the sky.

• To see information and data about the displayed object,

press the OBJECT INFO key. Press it once to display

the coordinates of the object. Press it again to display

the text description. Press BACK to return to the

previous screen.

• To slew to the object displayed, press ENTER.

• To see the next tour object, press the DOWN key.

Identify Button

Pressing the IDENTIFY button will search the mount’s da-

tabase catalogs and display the name and angular distances

to the nearest matching objects from the telescope’s current

location. This feature can serve two purposes. First, it can be

used to identify an unknown object in the ﬁeld of view of your

eyepiece. Additionally, Identify Mode can be used to ﬁnd

other celestial objects that are close to the objects you are

currently observing.

For example, if your telescope is pointed at the brightest

star in the constellation Lyra, choosing Identify will no doubt

return the star Vega as the star you are observing. However,

the Identify feature will also search its NGC and Solar

System databases and display any planets or Deep Sky

objects that are close by. In this example, the Ring Nebula

(M57) would display as being approximately 6° away.

The brightness and proximity of the objects displayed

can be deﬁned by the user using the Identify Filter under

Telescope Setup.

ENGLISH | 17

Direction Buttons

The hand control has four direction buttons in the center

of the hand control which control the telescope motion in

altitude (up and down) and azimuth (left and right). The

telescope can be controlled at nine different speed rates.

1 = 1/2x 6 = .3° / sec 64x

2 = 1x 7 = 1° / sec

3 = 4x 8 = 2° / sec

4 = 8x 9 = 3° / sec

5 = 16x

Motor Speed Button

Pressing the MOTOR SPEED button (12) allows you to

instantly change the speed rate of the motors from high

speed slew rate to precise guiding rate or anywhere in

between. Each rate corresponds to a number on the hand

controller key pad. The number 9 is the fastest rate and is

used for slewing between objects and locating alignment

stars. The number 1 on the hand control is the slowest rate

(2x sidereal) and can be used for accurate centering of

objects in the eyepiece. To change the speed rate of the

motors:

• Press the MOTOR SPEED key on the hand control.

The LCD will display the current speed rate.

• Press the number on the hand control that corresponds

to the desired speed.

The hand control has a “double button” feature that allows

you to instantly speed up the motors without having to

choose a speed rate. To use this feature, simply press the

arrow button that corresponds to the direction that you want

to move the telescope. While holding that button down,

press the opposite directional button. This will increase the

speed to the maximum slew rate.

When using the UP and DOWN buttons on the hand control,

the slower slew rates (6 and lower) move the motors in the

opposite direction than the faster slew rates (7- 9). This is

done so that an object will move in the appropriate direction

when looking into the eyepiece (i.e., pressing the up arrow

button will move the star upwards in the ﬁeld of view of the

eyepiece). However, if any of the slower slew rates (rate 6

and below) are used to center an object in the starpointer,

you may need to press the opposite directional button to

make the telescope move in the correct direction.

Help Button

In future ﬁrmware updates, this button will offer troubleshooting

tips. For your convenience, it currently functions as a shortcut

to the Messier Catalog.

Menu Button

The CGX mount contains many user-deﬁned setup

functions designed to give the user control over the

telescopes many features. All of the setup and utility features

can be accessed by pressing the MENU key and scrolling

through the options below.

Tracking Menu

Tracking Mode – This allows you to change the way the

telescope tracks depending on the type of mount being used

to support the telescope. The telescope has three different

tracking modes:

• EQ North – Used to track the sky when the telescope is

polar aligned in the Northern Hemisphere.

• EQ South – Used to track the sky when the telescope

is polar aligned in the Southern Hemisphere.

• Off – When using the telescope for terrestrial (land)

observation, the tracking can be turned off so that the

telescope never moves.

Tracking Rate – In addition to being able to move the

telescope with the hand control buttons, your telescope

will continually track a celestial object as it moves across

the night sky. The tracking rate can be changed depending

on what type of object is being observed:

• Sidereal – This rate compensates for the rotation of the

Earth by moving the telescope at the same rate as the

rotation of the Earth, but in the opposite direction. When

the telescope is polar aligned, this can be accomplished

by moving the telescope in right ascension only.

• Lunar – Used for tracking the Moon when observing the

lunar landscape.

• Solar – Used for tracking the Sun when solar observing

with the proper ﬁlter.

View Time-Site Menu

This menu displays the current time and longitude/latitude

downloaded from the optional SkySync GPS receiver.

It will also display other relevant time-site information like

time zone, daylight saving and local sidereal time. Local

sidereal time (LST) is useful for knowing the right ascension

of celestial objects that are located on the Meridian at that

time. View Time-Site will always display the last saved time

and location entered while it is linking with the GPS. Once

current information has been received, it will update the

displayed information. If GPS is switched off or not present, the

hand control will only display the last saved time and location.

The Hand Control Menu

The “Hand Control” menu allows you to customize certain

features of the NexStar+ hand control. To access this menu,

press the MENU button (#7 on the keypad) and use the

scroll buttons to select “Hand Control” and press ENTER.

18 | ENGLISH

Use the scroll buttons to select from the following options:

• Lights Control: Independently adjust the brightness of

the number keypad and the LCD.

• Scrolling Menu: Adjust how fast words move across the

face of the LCD.

• Toggle Bold Font: Change the format of the font

displayed on the LCD from normal to boldface.

• Set Contrast: Use the scroll keys to adjust the contrast

of the LCD.

• Set Language: Change the displayed language on

the LCD.

NOTE: The Set Language feature may also appear the ﬁrst

time you use your new hand control. You may also initi-

ate it at any time by holding down the Option button (the

Celestron logo) for 10 seconds while powering up the

telescope.

Scope Setup Menu

Setup Time-Site – Allows the user to customize the

telescope’s display by changing time and location

parameters (such as time zone and daylight savings).

Anti-backlash – All mechanical gears have a certain

amount of backlash or play between the gears. This play

is evident by how long it takes for a star to move in the

eyepiece when the hand control arrow buttons are pressed

(especially when changing directions). The CGX-L

anti-backlash feature allows the user to compensate for

backlash by inputting a value which quickly rewinds the

motors just enough to eliminate the play between gears.

The amount of compensation needed depends on the

slewing rate selected; the slower the slewing rate the longer

it will take for the star to appear to move in the eyepiece.

There are two values for each axis, positive and negative:

• Positive is the amount of compensation applied when you

press the button in order to get the gears moving quickly

without a long pause.

• Negative is the amount of compensation applied when you

release the button, winding the motors back in the other

direction to resume tracking.

Normally, both values should be the same. You will need to

experiment with different values (from 0-99); a value between

20 and 50 is usually best for most visual observing, whereas

a higher value may be necessary for photographic guiding.

To set the anti-backlash value, scroll down to the anti-backlash

option and press ENTER. While viewing an object in the

eyepiece, observe the responsiveness of each of the four

arrow buttons. Note which directions you see a pause in the

star movement after the button has been pressed. Working

one axis at a time, adjust the backlash settings high enough

to cause immediate movement without resulting in a

pronounced jump when pressing or releasing the button.

Now, enter the same values for both positive and negative

directions. If you notice a jump when releasing the button but

setting the values lower results in a pause when pressing

the button, use the higher value for positive, but use the

lower value for negative. The telescope will remember these

values and use them each time it is turned on until they are

changed.

Filter Limits – When an alignment is complete, the telescope

automatically knows which celestial objects are above the

horizon. As a result, when scrolling through the database

lists (or selecting the Tour function), the hand control will

display only those objects that are known to be above the

horizon when you are observing. You can customize the

object database by selecting altitude limits that are appropriate

for your location and situation. For example, if you are

observing from a mountainous location where the horizon

is partially obscured, you can set your minimum altitude limit

to read +20°. This will make sure that the hand control only

displays objects that are higher in altitude than 20°.

TIP: If you want to explore the entire object database, set

the maximum altitude limit to 90° and the minimum limit

to –90°. This will display every object in the database

lists regardless of whether it is visible in the sky from your

location.

Direction Buttons – The direction a star appears to move

in the eyepiece changes depending on which side of the

Meridian the telescope tube is on. This can create confusion

especially when guiding on a star when doing astroimaging.

To compensate for this, the direction of the drive control keys

can be changed. To reverse the button logic of the hand

control, press the MENU button and select Direction

Buttons from the Utilities menu. Use the Up/Down arrow

keys (10) to select either the azimuth (right ascension) or

altitude (declination) button direction and press ENTER.

Select either positive or negative for both axes and press

ENTER to save. Setting the azimuth button direction to

positive will move the telescope in the same direction

that the telescope tracks (i.e., towards the west). Setting

the altitude buttons to positive will move the telescope

counterclockwise along the declination axis.

GoTo Approach – Lets the user deﬁne the direction that

the telescope will approach when slewing to an object. This

allows the user the ability to minimize the effects of backlash

when slewing from object to object. Just like with Direction

Buttons, setting GoTo Approach to positive will make the

telescope approach an object from the same direction

as tracking (west) for azimuth and counterclockwise in

declination. Declination GoTo approach will only apply while

the telescope tube is on one side of the Meridian. Once the

tube passes over to the other side of the Meridian, the GoTo

approach will need to be reversed.

To change the GoTo approach direction, simply choose

GoTo Approach from the Scope Setup menu, select either

Altitude or Azimuth approach, choose positive or negative

and press ENTER.

ENGLISH | 19

HINT: In order to minimize the affect of gear backlash on

pointing accuracy, the settings for Button Direction should

ideally match the settings for GoTo Approach. By default,

using the up and right direction buttons to center alignment

stars will automatically eliminate much of the backlash in the

gears. If you change the GoTo approach of your telescope,

it is not necessary to change the Button Direction as well.

Simply take notice of the direction the telescope moves

when completing its ﬁnal GoTo approach. If the telescope

approaches its alignment star from the west (negative

azimuth) and clockwise (negative altitude) then make sure

that the buttons used to center the alignment stars also move

the telescope in the same directions.

Autoguide Rate – Allows the user to set an autoguide

rate as a percentage of sidereal rate. This is helpful when

calibrating your telescope to a CCD autoguider for long

exposure astroimaging.

Meridian – This feature instructs the mount on how to

respond when it is slewing to objects that are accessible

from both sides of the Meridian. The Meridian feature allows

the telescope tube to remain on a desired side of the mount

when slewing, and continue to track according to the R.A.

slew limits the user has set. See R.A. Limits below. The

Meridian feature allows for four choices:

• Favor Current – Allows the mount to favor whatever side

of the mount that it is currently on when slewing to objects

close to the Meridian. For example, if your R.A. slew limits

are set to allow the mount to track 10° past the meridian,

then the telescope will continue to stay on its current side

of the Meridian when slewing to objects that are as far as

10° beyond your Meridian.

• Favor West – If the target object is accessible from both

sides of the mount, selecting “Favor West” instructs the

mount to point to the object as if it were on the west side

of the meridian. The optical tube will then be positioned on

the east side of the mount and pointing west.

• Favor East – If the target object is accessible from both

sides of the mount, selecting “Favor East” instructs the

mount to point to the object as if it were on the east side

of the meridian. The optical tube will then be positioned on

the west side of the mount and pointing east.

• Disable – This is the default setting, which instructs the

mount to always swing around to the other side of the pier

as required to view objects on the opposite side of the

Meridian. However, once at the desired object, the mount

will continue to track past the Meridian according to the

R.A. slew limits that have been set.

Mount Settings – Once the mount settings have been

calibrated (see Utilities section below) the values are stored

and displayed in the hand control. It is not recommended

that the calibration values be changed. However each setting

can be changed if necessary to improve the performance of

the telescope.

• Cone Value – This is the cone error value set when

Utilities/Calibrate Mount/DEC Switch – Cone is carried out.

• DEC Index – This is the declination index error value that

is stored when calibration stars are added after your initial

star alignment.

• R.A. Index – This is the R.A. index error value set when

Utilities/Calibrate Mount/R.A. Switch is carried out.

R.A. Limits – Sets the limits that the telescope can slew or

track in Right Ascension (R.A.) before stopping. The slew

limits are represented in degrees and by default set to 0°,

being the position of the telescope when the counterweight

bar is extended out horizontally. However, the slew limits can

be customized depending on your needs. For example, if

you are using CCD imaging equipment that has cables that

are not long enough to move with the telescope as it slews

across the sky, you can adjust the slew limit on the side of

the mount that is restricted by the cables, and command the

mount the stop slewing before it reaches this point. Or if you

are taking an image of an object that has just crossed the

Meridian, you can set the limit to allow the mount to continue

tracking in the same direction past the Meridian without the

need to “ﬂip” the telescope around to the opposite side of

the mount (see Meridian feature above). Using the ﬁrst example

above, the user could slew the telescope in R.A. (azimuth)

until it reaches the point that the cables are extended to their

maximum. Then by displaying the telescope’s azimuth in this

position (by looking at Get Axis Position under the Utilities

menu) you can determine the telescope’s azimuth at its most

extended position. Enter this azimuth reading for either the

maximum or minimum azimuth slew limit to ensure that the

telescope will not slew beyond this point. The telescope slew

limits can be set to automatically stop anywhere between

40° above level to 20° below level. To set the R.A. slew limit

select the following:

• R.A. East Limit – Enter a number between +40° to -20°

to deﬁne the slew limit when the tube is on the east side of

the mount.

• R.A. West Limit – Enter a number between +40° to -20°

to deﬁne the slew limit when the tube is on the west side

of the mount.

• Disable Limits – This disables any pre-deﬁned values

that have been entered and allows the mount to track

the maximum amount pass the Meridian (i.e., -20° on

both sides)

20 | ENGLISH

WARNING: In order for the telescope to be able to slew

to a star from the direction that minimizes the amount of

backlash in the gears, it may be necessary for the telescope

to slew beyond the speciﬁed slew limit in order to approach

the star from the correct direction. This can limit your ability

to slew to an object by as much as 6° from the R.A. slew

limit set in the hand control. If this proves to be a problem,

the direction that the telescope takes to center an object can

be changed. To change the telescopes slewing direction, see

GoTo Approach under the Scope Setup menu.

Custom Rate 9 – This allows you to customize the speed at

which the mount slews to a target. You can set the R.A. and

Dec axes individually. The max speed of the CGX-L is 4°/

second (3°/second is default).

Utilities Menu

Scrolling through the MENU (9) options will also provide

access to several advanced utility functions within the

telescope such as; Calibrate Mount, Hibernate as well as

many others.

Calibrate Mount – In order to optimize the performance

and pointing accuracy of the telescope, the mount has

built-in calibration routines allowing it to compensate for

mechanical variation inherent in every German equatorial

mount. Each calibration is completely automatic and in

most cases only needs to be performed once. It is highly

recommended that you take a few minutes to go through

the mount calibration procedures.

• R.A. Switch – This procedure records the offset error

when the right ascension index mark is aligned at start-up.

Calibrating the R.A. Index will improve the accuracy of your

initial star alignments when aligning the telescope in the

future.

• GoTo Calibration – GoTo Calibration is a useful tool

when attaching heavy visual or photographic accessories

to the telescope. GoTo Calibration calculates the amount

of distance and time it takes for the mount to complete

its ﬁnal slow GoTo when slewing to an object. Changing

the balance of the telescope can prolong the time it takes

to complete the ﬁnal slew. GoTo Calibration takes into

account any slight imbalances and changes the ﬁnal GoTo

distance to compensate.

Home Position – The telescope’s “home” position is a

user-deﬁnable position that is used to store the telescope

when not in use. The home position is useful when storing

the telescope in a permanent observatory facility. By default

the Home position is the same as the index position used

when aligning the mount.

To set the Home position for your mount, simply use the

arrow buttons on the hand control to move the telescope

mount to the desired position. Select the Set option and

press Enter.

Select the GoTo option to slew the telescope back to the

Home position at any time.

Factory Settings – Returns the hand control to its original

factory settings. Parameters such as backlash compensation

values, initial date and time, longitude/latitude, along with

slew and ﬁlter limits will be reset. However, stored parameters

such as user deﬁned objects will remain saved even when

Factory Settings is selected. The hand control will ask you

to press the “0” key before returning to the factory default

setting.

Version – Selecting this option will allow you to see the

current version number of the hand control and motor

control. The ﬁrst set of numbers indicate the hand control

software version. For the motor control, the hand control

will display two sets of numbers; the ﬁrst numbers are for

azimuth and the second set are for altitude.

Get Axis Position – Displays the relative altitude and

azimuth for the current position of the telescope.

GoTo Axis Position – Allows you to enter a speciﬁc relative

altitude and azimuth position and slew to it.

Hibernate – Hibernate allows the telescope to be completely

powered down and still retain its alignment when turned

back on. This not only saves power, but is ideal for those

that have their telescope permanently mounted or leave their

telescope in one location for long periods of time. To place

your telescope in Hibernate mode:

1. Select Hibernate from the Utility Menu.

2. Move the telescope to a desire position and

press ENTER.

3. Power off the telescope. Remember to never move

your telescope manually while in Hibernate mode.

Once the telescope is powered on again, the display will

read Wake Up. After pressing Enter, you have the option of

scrolling through the time/site information to conﬁrm the

current setting. Press ENTER to wake up the telescope.

HINT: Pressing BACK at the Wake Up screen allows

you to explore many of the features of the hand control

without waking the telescope up from hibernate mode.

To wake up the telescope after BACK has been pressed,

select Hibernate from the Utility menu and press ENTER.

Do not use the direction buttons to move the telescope

while in hibernate mode.

Sun Menu

For safety purposes, the Sun will not be displayed as a

database object unless it is ﬁrst enabled. To enable the Sun,

go to the Sun Menu and press ENTER. The Sun will now

be displayed in the Planets catalog and can be used as an

alignment object when using the Solar System Alignment

La pagina sta caricando ...

Celestron 91531 Manuale utente

Questo manuale è adatto anche per

Celestron 91531 Manuale utente

in altre lingue

Documenti correlati

Altri documenti