Tascam DP-24SD Manuale del proprietario

D01258820B

DP-24SD

Digital Portastudio

OWNER'S MANUAL

2

TASCAM DP-24SD

IMPORTANT SAFETY PRECAUTIONS

WARNING: TO PREVENT FIRE

OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

INFORMATION TO THE USER

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures.

a) Reorient or relocate the receiving antenna.

b) Increase the separation between the equipment and

receiver.

c) Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

d) Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipment not expressly

approved by TEAC CORPORATION for compliance could void

the user’s authority to operate this equipment.

For U.S.A.

For Canada

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

CET APPAREIL NUMERIQUE DE LA CLASSE B EST CONFORME A

LA NORME NMB-003 DU CANADA.

Declaration of Conformity

Responsible party: TEAC AMERICA, INC.

Address: 1834 Gage Road, Montebello,

California, U.S.A.

Telephone number: 1-323-726-0303

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

This product complies with the European

Directives request and the other

Commission Regulations.

TASCAM DP-24SD

3

IMPORTANT SAFETY INSTRUCTIONS

• The apparatus draws nominal non-operating power

from the AC outlet with its POWER or STANDBY/ON

switch not in the ON position.

• The mains plug is used as the disconnect device, the

disconnect device shall remain readily operable.

• Caution should be taken when using earphones or

headphones with the product because excessive

sound pressure (volume) from earphones or

headphones can cause hearing loss.

• If you are experiencing problems with this product,

contact TEAC for a service referral. Do not use the

product until it has been repaired.

CAUTION

• Do not expose this apparatus to drips or splashes.

• Do not place any objects filled with liquids, such as

vases, on the apparatus.

• Do not install this apparatus in a confined space

such as a book case or similar unit.

• The apparatus should be located close enough to

the AC outlet so that you can easily grasp the power

cord plug at any time.

• If the product uses batteries (including a battery

pack or installed batteries), they should not be

exposed to sunshine, fire or excessive heat.

• CAUTION for products that use replaceable lithium

batteries: there is danger of explosion if a battery is

replaced with an incorrect type of battery. Replace

only with the same or equivalent type.

WARNING

• Products with Class ! construction are equipped

with a power supply cord that has a grounding

plug. The cord of such a product must be plugged

into an AC outlet that has a protective grounding

connection.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliers) that produce heat.

9 Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are provid-

ed for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replace-

ment of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table

specied by the manufacturer, or sold with the appa-

ratus. When a cart is used, use caution when moving

the cart/apparatus combination to avoid injury from

tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

4

TASCAM DP-24SD

Safety Information

8

For European Customers

Disposal of electrical and electronic equipment

(a) All electrical and electronic equipment should be

disposed of separately from the municipal waste

stream via designated collection facilities appointed

by the government or the local authorities.

(b) By disposing of the electrical and electronic

equipment correctly, you will help save valuable

resources and prevent any potential negative effects

on human health and the environment.

(c) Improper disposal of waste equipment can have

serious effects on the environment and human health

as a result of the presence of hazardous substances in

electrical and electronic equipment.

(d) The crossed out wheeled dust bin symbol indicates

that electrical and electronic equipment must be

collected and disposed of separately from household

waste.

(e) The return and collection systems are available to

the end users. For more detailed information about

disposal of old electrical and electronic equipment,

please contact your city office, waste disposal service

or the shop where you purchased the equipment.

TASCAM DP-24SD

5

Contents

1 – Introduction ..............................................8

Features .................................................................................. 8

Items included with the product .................................. 8

Conventions used in this manual ..................................8

Trademarks ............................................................................ 9

Precautions for placement and use ..............................9

Beware of condensation ...................................................9

Cleaning the unit .................................................................9

About SD cards ....................................................................9

Precautions for use ...................................................... 9

Using the TEAC Global Site .............................................. 9

User registration ..................................................................9

2 - Quick Guide .............................................. 10

Playback and mixing ........................................................10

Preparation ................................................................... 10

Listening to the demo song ...................................10

Recording and mastering ..............................................11

Creating a new song .................................................12

Connecting and setting the input sources ....... 12

Setting the guitar as the recording source for

TRACK 1..........................................................................13

Adjusting and monitoring the input level ........13

Recording a guitar to TRACK 1 ..............................13

Playing back the recording ..................................... 14

Recording a guitar to TRACK 2 ..............................14

Recording a vocal to TRACK 3 ................................15

Mixing the tracks ........................................................ 16

Mastering a recording ..............................................16

Shutting down ...................................................................18

3 – Names and Functions of Parts ...............19

Top panel .............................................................................19

Front panel ..........................................................................22

Rear panel ............................................................................23

Home screen ....................................................................... 23

Menu structure ..................................................................24

Screen operations .............................................................25

4 – Preparation ..............................................26

Inserting and removing SD cards ................................26

Inserting an SD card ..................................................26

Removing the card ....................................................26

About write-protected SD cards ..........................26

Powering the unit .............................................................26

Changing the outlet plug ........................................26

Start-up & Shutdown .......................................................27

Starting up the unit ...................................................27

Shutting down ............................................................27

Setting the date and time .............................................. 27

Preparing an SD card for use ........................................28

Recorder modes ................................................................28

Connecting other equipment ......................................28

Front panel ...................................................................28

Rear panel .....................................................................29

Adjusting the contrast .....................................................29

5 - Song Management ..................................30

Editing names ..................................................................... 30

Loading a song ..................................................................30

Creating a new song ........................................................31

Saving a song .....................................................................31

Viewing song information .............................................32

Copying songs ...................................................................32

Erasing songs ......................................................................32

Protecting songs ...............................................................33

Deleting unnecessary audio data from a song ......33

Changing a song name ...................................................34

6 - Basic Recording........................................35

Selecting the input sources ........................................... 35

Assigning inputs ................................................................35

Assigning to a mono track ......................................35

Assigning to a stereo track .....................................35

Assigning to a stereo bus ........................................35

Checking the assignment .......................................35

Canceling an assignment ........................................35

Using phantom power ....................................................36

Monitoring...........................................................................36

Monitor selection .......................................................36

OL indicators and level meters ....................................36

Peak hold display .......................................................37

Setting the Mixer screen ................................................37

Using the input equalizer ........................................ 37

DIGITAL TRIM setting (Track only) ........................38

Sending signals to internal/external effects ....38

Enabling insert effects .............................................38

Setting the stereo position ..................................... 38

Changing the signal phase .....................................38

Checking the fader level .......................................... 39

Solo ........................................................................................39

Muting tracks ......................................................................39

Rehearsing the recording ..............................................39

Making the first recording .............................................39

Multitrack recording ........................................................40

Setting the tracks for recording ............................40

Setting track pan and level .....................................40

Input selection and assignment ...........................40

Setting input levels ....................................................40

Recording ......................................................................40

Undoing an operation .....................................................40

Undo feature settings ...............................................40

Undoing the last operation (single undo) ......... 41

Undoing older operations (multiple undo) ......41

6

TASCAM DP-24SD

Contents

7 - Recorder Functions ..................................42

Punching in and out.........................................................42

Using a foot switch to punch in/out .................... 42

Setting the foot switch .............................................42

Bouncing tracks .................................................................43

Performing the track bouncing ............................43

Checking the result ...................................................43

Direct Location Function................................................43

Locating directly a specified time ........................44

Locating directly a specified measure/beat .....44

Location marks ..................................................................44

Setting a location mark ............................................44

Skipping to location marks .....................................44

Deleting a location mark .........................................44

Returning to zero or the last recording position ...44

Fast forwarding and rewinding ...................................45

Cueing with the JOG/DATA dial ...................................45

Jogging while viewing a waveform ....................45

Jogging while listening to audio ..........................45

Repeat playback ................................................................45

Setting IN/OUT points ..............................................45

Using repeat playback ..............................................46

Jumpback playback .........................................................46

Checking cueing points (preview) ..............................46

Automatic punching in and out ..................................46

Setting punch-in/out points ..................................47

Checking punch-in/out points .............................. 47

Rehearsing with automatic punching ................47

Recording with automatic punching ..................48

Checking a take...........................................................48

Virtual tracks .......................................................................48

Recording to virtual tracks ......................................48

Assigning virtual tracks ............................................48

8 - Track Editing ............................................49

Overview of track editing...............................................49

Editing points ..............................................................49

Basic editing procedures .........................................49

Explanation of items .................................................49

COPY/PASTE ........................................................................50

COPY/INSERT ....................................................................... 50

MOVE/PASTE ....................................................................... 51

MOVE/INSERT .....................................................................51

OPEN (Insert Silence)........................................................51

CUT (Remove Part) ............................................................51

SILENCE (Erase Part) .........................................................52

CLONE TRACK (Track Duplication) ..............................52

CLEAN OUT (Delete Track) .............................................52

9 - Using Built-In Effects ...............................53

Dynamic effects .................................................................53

Inserting a dynamic effect ...................................... 53

Editing a dynamic effect ..........................................53

Guitar effects ......................................................................53

Inserting a guitar effect ...........................................53

Editing guitar effects ................................................53

Calling effects from the guitar effect library....54

Saving guitar effects in the library ....................... 54

Send effects ........................................................................54

Using send effects .....................................................54

Editing send effects ...................................................54

Calling the send effect library ...............................54

Saving send effects in the library ......................... 54

10 - Mixing Down and Mastering Tracks .....55

Mixing down tracks .......................................................... 55

Levels and balance ....................................................55

Fader group ..................................................................55

Stereo position (panning) .......................................55

Track equalizer ............................................................55

Send effects .................................................................56

Creating a master file .......................................................56

Setting the start and end points ..........................56

Creating a master file ................................................ 57

Exiting Mixdown mode ............................................ 57

Checking the master file ................................................57

Ending master file checking ...................................57

Finishing up a master file (mastering) .......................58

Mastering procedures ..............................................58

Using the mastering equalizer ..............................59

Using mastering compression ............................... 59

Using normalize ..........................................................60

Exiting Mastering mode ..........................................60

11 - Various Other Functions ........................61

Metronome .........................................................................61

Tuner function ....................................................................62

Setup (PREFERENCE) ........................................................62

Setting automatic power saving ..........................63

Setting automatic monitoring ..............................63

Setting the song name format ..............................63

Restoring the initial preference settings ..................63

Viewing information ........................................................64

12 - SD Card Management ............................65

Quick formatting an SD card ........................................65

Full formatting an SD card .............................................66

13 - Exchanging Data with a Computer .......67

Operating system requirements .................................67

Connecting to a computer ............................................67

Disconnecting .............................................................68

Track import and export ................................................. 68

TASCAM DP-24SD

7

Contents

Importing tracks .........................................................68

Exporting tracks .........................................................69

Deleting files from the AudioDepot folder .............70

14 – Troubleshooting ....................................71

15 – Messages ...............................................72

General messages .............................................................72

16 – Specifications ........................................75

Ratings ..................................................................................75

Input/output ratings ........................................................75

Analog audio input/output ratings .....................75

Control input/output ratings .................................75

Audio performance ..........................................................75

Operating requirements ................................................75

General .................................................................................76

Dimensional drawings ....................................................76

Block diagram.....................................................................77

Level diagram .....................................................................78

8

TASCAM DP-24SD

1 – Introduction

Thank you very much for purchasing the TASCAM DP-24SD

Digital Portastudio.

Before connecting and using the unit, please take time to read

this manual thoroughly to ensure you understand how to

properly set up and connect the unit, as well as the operation

of its many useful and convenient functions. After you have

finished reading this manual, please keep it in a safe place for

future reference.

You can also download the Owner's Manual from the TEAC

Global Site (http://teac-global.com/).

Features

This unit uses SD cards for multitrack recording of up to 8 tracks

and playback of up to 24 tracks simultaneously. Multiple tracks

can be mixed down to stereo to create a master file by using the

built-in mixer functions.

Master files can be transferred to a computer that is connected

via USB. Moreover, since transferring data between the unit and

a computer is possible, you can copy tracks and master files, and

back up song files to a computer.

• 24-track Digital Multitrack Recorder that uses SD cards as

recording media

• Supports SDHC standards for large capacity SD cards of up

to 32GB

• Multitrack recorder functions include simultaneous 8 track

recording + 24 track playback (44.1/48kHz, 16/24bit)

• 18+1 45mm faders (for track and master level adjustment)

• Each track has independent SELECT button and REC button

• +48V Phantom power supported mic input

• Eight balanced mic/line inputs (XLR/TRS combo jacks)

• High-impedance guitar input supported (INPUT H only:

6.3mm (1/4") TS phone jack)

• 3.5-inch large TFT color LCD display

• Independent 3-band equalizers for each input and playback

track

• Mixing down to a dedicated master file possible

• Included mastering effects can be used on mix downs of

master files

• Includes Reverb and various other effects that can be

independently adjusted for each playback track

• Auto punch in/out function

• Track bounce function

• Track editing functions include COPY INSERT, COPY PASTE,

MOVE INSERT, MOVE PASTE, OPEN, CUT, SILENCE, CLONE

TRACK, and CLEAN OUT

• Undo and redo functions, including history level setting

• Locate Mark function

• Tuner and metronome functions

• Song data and WAVE files can be copied and backed up to a

computer connected via USB2.0

• Punch in/out and other functions can be assigned to and

controlled by a foot switch (TASCAM RC-3F, sold separately)

Items included with the product

The DP-24SD package contains the following items.

Take care when opening the package to avoid damaging the

items. Keep the packing materials for transportation in the future.

Please contact the store where you purchased this unit if any of

these items are missing or have been damaged during transpor-

tation.

• Main unit ...............................................................................................×1

• AC adapter (PS-P1220E) ...................................................................×1

• SD memory card (inserted into the unit) ...................................×1

• Owner's Manual (this manual) .......................................................×1

The warranty is included at the end of this manual.

CAUTION

Always use the included PS-P1220E AC adapter with this

unit. Moreover, do not use the included AC adapter with

other equipment. Doing so could cause malfunction, fire or

electric shock.

NOTE

The included AC adapter (PS-P1220E) is shipped with

exchangeable outlet plugs. For details about changing the

outlet plug, see “Changing the outlet plug” on page 26.

Conventions used in this manual

The following conventions are used in this manual.

• Buttons, connectors and other physical parts of this unit are

written using a bold font like this: MENU button.

• Text displayed on the display of the unit appears like this:

MENU

.

• The four buttons beneath the LCD display (F1 to F4) are

function buttons. The functions displayed at the bottom of

each screen are sometimes shown after the button names

in parentheses.

Example: F1 (

TIMELINE

) button, F4 (t) button.

• SD and SDHC memory cards are called “SD cards”.

• Text displayed on a computer monitor appears like this: OK.

• Additional information is provided as necessary in tips,

notes and cautions

TIP

These are tips about how to use the unit.

NOTE

These include additional explanations and special cases.

CAUTION

Failure to follow these instructions could result in injury,

equipment damage or lost data, for example.

TASCAM DP-24SD

9

1 – Introduction

Trademarks

• TASCAM and PORTASTUDIO are trademarks of TEAC

Corporation, registered in the U.S. and other countries.

• SDHC Logo is a trademark of SD-3C, LLC.

• Windows, Windows XP, Windows Vista, Windows 7 and

Windows 8 are either registered trademarks or trademarks

of Microsoft Corporation in the United States and/or other

countries.

• iMac, Mac OS and OS X are trademarks of Apple Inc.

• Pentium and Intel are trademarks of Intel Corporation in the

U.S. and/or other countries.

• Other company names, product names and logos in this

document are the trademarks or registered trademarks of

their respective owners.

Any data, including, but not limited to information,

described herein are intended only as illustrations of such

data and/or information and not as the specifications for

such data and/or information. TEAC Corporation disclaims

any warranty that any use of such data and/or information

shall be free from infringement of any third party's intel-

lectual property rights or other proprietary rights, and

further, assumes no liability of whatsoever nature in the

event of any such infringement, or arising from or connected

with or related to the use of such data and/or information.

This product is designed to help you record and reproduce

sound works to which you own the copyright, or where you

have obtained permission from the copyright holder or the

rightful licensor. Please use the product appropriately.

Under no circumstances will TEAC Corporation be respon-

sible for the consequences of any illegal copying performed

using the recorder.

Precautions for placement and use

• The operating temperature should be between 5°C and

35°C (41°F and 95°F).

• Do not install in the following types of places. Doing

so could degrade the sound quality and/or cause

malfunctions.

Places with significant vibrations or that are otherwise

unstable

Near windows or other places exposed to direct sunlight

Near heaters or other extremely hot places

Extremely cold places

Places with bad ventilation or high humidity

Very dusty locations

• Make sure that the unit is mounted in a level position for

correct operation.

• Do not place any object on the unit for heat dissipation.

• Avoid installing this unit on top of any heat-generating

electrical device such as a power amplifier.

Beware of condensation

If the unit is moved from a cold to a warm place, or used after a

sudden temperature change, there is a danger of condensation;

vapor in the air could condense on the internal mechanism,

making correct operation impossible. To prevent this, or if this

occurs, let the unit sit for one or two hours at the new room

temperature before using.

Cleaning the unit

To clean the unit, wipe it gently with a soft dry cloth. Do not

wipe the unit with chemical cleaning cloths, paint thinner,

alcohol or other chemical agents because they could damage its

surface or cause discoloration.

About SD cards

This unit uses SD cards for recording and playback.

SD and SDHC cards that are at least 512 MB in size can be used.

A list of SD cards that have been confirmed for use with this unit

can be found on our web site. Please access to a product page of

this product from the TEAC Global Site (http://teac-global.com)

to find the list or contact the TASCAM customer support service.

Precautions for use

SD cards are delicate media. In order to avoid damaging a card

or the card slot, please take the following precautions when

handling them.

• Do not leave them in extremely hot or cold places.

• Do not leave them in extremely humid places.

• Do not let them get wet.

• Do not put things on top of them or twist them.

• Do not hit them.

• Do not remove or insert an SD card when the power is ON.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

In the TASCAM Downloads section, select the desired language

to open the Downloads website page for that language.

Product registration

Customers in the USA, please visit the following TASCAM

website to register your TASCAM product online.

http://tascam.com/

10

TASCAM DP-24SD

2 - Quick Guide

Playback and mixing

In this section, we will play back the demo song on the included

SD card.

When this unit is purchased new, the SD card with the demo

song on it is already installed in the unit, but we will start by

explaining how to insert an SD card using the procedures below.

Preparation

1. Insert the included SD card into the SD card slot on the rear

panel. Be careful not to forcibly insert the card in the wrong

direction. Doing so could damage the SD card slot or the SD

card.

2. Connect the supplied AC adapter (PS-P1220E) to the DC IN

12V jack on the rear panel.

AC outlet

DC plug

PS-P1220E

CAUTION

Always use the included PS-P1220E AC adapter.

Use of a different adapter could cause malfunction, fire or

electric shock.

3. Connect headphones to the PHONES jack on the front

panel.

Headphones

4. Press and hold the STANDBY/ON button for a few seconds

on the rear panel to turn the power ON. When the unit starts,

the Home screen appears on the display.

Start-up screen

Home screen

CAUTION

•

Do not remove or insert an SD card when the power is ON.

Always turn the power OFF (standby) before removing or

inserting an SD card.

•

When the power is on, do not cut the power to the unit by,

for example disconnecting the power cord. All settings made

since the last time you saved will not be saved. If you cut the

power while an SD card is being accessed, all recorded songs

and data may be damaged and cannot be recovered.

•

Before turning the power ON, minimize the headphones

volume and the volume on any monitoring system

connected to this unit.

TIP

If an amplifier or powered speakers are connected to the

MONITOR OUT jacks, you can monitor using speakers.

Listening to the demo song

The included SD card in the unit contains a demo song. We

will use this demo song to practice listening to and mixing a

recording.

1. Press the HOME button to open the Home screen.

TASCAM DP-24SD

11

2 - Quick Guide

2. When the recorder is stopped, press the MENU button to

open the

MENU

screen.

3. Use the JOG/DATA dial or the CURSOR (5/b/g/t)

buttons to select (green highlight)

SONG

, and then press

the F4 (t) button.

The

SONG LIST

screen appears.

4. Use the JOG/DATA dial or the CURSOR (5/b) buttons to

select

DEMO SONG

, and then press the F4 (t) button to

open a sub-menu.

5. Use the JOG/DATA dial or the CURSOR (5/b) buttons to

select

LOAD

, and then press the F4 (t) button.

The

SONG LOAD

pop-up window appears.

6. Press the F2 (

YES

) button to load the demo song.

The demo song is loaded and the display returns to the

SONG LIST

screen.

7. Press the HOME button to return to the Home screen.

8. Press the PLAY (7) button, and raise the TRACK 1 to 23/24

faders, the STEREO fader and the MONITOR LEVEL knob to

listen to the demo song.

The STEREO fader adjusts the overall volume of TRACK 1 to

23/24. The standard position of the STEREO fader is 0dB.

Use TRACK 1 to 23/24 faders to adjust the balance of the

tracks.

Use the MONITOR LEVEL knob to adjust the final

monitoring volume.

9. Press the MIXER button to open the

Mixer

screen.

10. 1Press the SOURCE button to select INPUT A to H, or press

the SELECT button to select a track to be set, and then use

the PAN knob to set the stereo signal position of each track.

TIP

•

Press the STOP (8) and REW (m) (TO ZERO) buttons at

the same time to return to the beginning of the song (ZERO

point) (TO ZERO function).

•

If you press the wrong button and open a different screen,

press the HOME button to return to the Home screen at any

time.

Recording and mastering

In this section we will practice multitrack recording.

Here we will explain how to connect an electric guitar and

rhythm guitar to INPUT H, and an external microphone to

INPUT B.

In the following example, we will explain how to record a

rhythm guitar part with an electric guitar to track 1 and a lead

guitar part to track 2. Then, we will use the external microphone

to record vocals to track 3. Finally, we will mix down the tracks

to stereo.

We will assume that you have already followed the instruc-

tions in the previous section, and that you have connected the

monitoring equipment, started the unit and inserted the SD

card.

12

TASCAM DP-24SD

2 - Quick Guide

Creating a new song

1. When the recorder is stopped, press the MENU button to

open the

MENU

screen.

2. Use the JOG/DATA dial or the CURSOR (5/b/g/t)

buttons to select (green highlight)

SONG

, and then press

the F4 (t) button.

The

SONG LIST

screen appears.

3. Press the F4 (t) button to open the sub-menu and then

use the JOG/DATA dial or the CURSOR (5/b) buttons to

select

CREATE

.

4. Press the F4 (t) button to open the

SONG CREATE

pop-up window.

The created song is given the name

SONG_0002

.

5. Change the name (title) of the song as necessary in the item

Name

. (See “Editing names” on page 30.)

6. Use the CURSOR (5/b) buttons to move the cursor (blue

highlight) to select

Bit

(Bit rate),

Hz

(Sampling frequency),

and then use the JOG/DATA dial to set.

7. Press the F2 (

YES

) button.

The currently loaded song is saved and a new song is

created.

8. Press the HOME button to return to the Home screen.

Connecting and setting the input sources

1. Connect an electric guitar to the MIC/LINE INPUTS H jack on

the rear panel.

Guitar

2. Set the LINE-GUITAR switch to GUITAR on the rear panel.

The GUITAR indicator lights.

GUITAR indicator

Now the guitar becomes the input source for INPUT H.

TIP

When connecting an electric-acoustic guitar with a built-in

preamp or an active-type electric guitar, or when using an

effects pedal, for example, between the guitar and this unit,

set the LINE-GUITAR switch to LINE on the rear panel.

TASCAM DP-24SD

13

2 - Quick Guide

Setting the guitar as the recording source

for TRACK 1

When you press the ASSIGN button to open the Assign screen,

the default screen setting for the recording source is

A

(INPUT

A) for TRACK 1,

B

(INPUT B) for TRACK 2,

C

(INPUT C) for TRACK

3, and so on for

D

to

H

(INPUT D to H) for TRACK 4 to 8. (See

“Assigning inputs” on page 35.)

Since initially the input source of the INPUT H is set as the

recording source of the TRACK 8, you must change the recording

source to TRACK 1.

Follow the procedure below to change the recording source of

the TRACK 1.

1. Press the ASSIGN button to open the Assign screen.

2. Use the CURSOR (5/b/g/t) buttons or press the

SELECT button for TRACK 1 and align the cursor (frame) on

the Assign screen with

TRACK 1

.

3. Use the JOG/DATA dial or the SOURCE button for INPUT H

to set the recording source of TRACK 1 to

H

.

Adjusting and monitoring the input level

1. Press the HOME button to return to the Home screen.

2. Press the REC button for TRACK 1.

The REC button flashes and the unit enters recording

standby.

3. Use the TRIM knob for INPUT H to adjust the guitar input

level. Set the TRIM knob so that the OL indicator for INPUT H

does not light even when the loudest sound to be recorded

is input.

If the OL indicator continues to light even when the TRIM

knob is turned down, the guitar signal itself is too loud. In

this case, lower the output level on the guitar.

OL indicator

When you play the guitar, the input level is shown by the

level meter for

1

(TRACK 1) on the display.

When you raise the fader for TRACK 1, the STEREO fader

and the MONITOR LEVEL knob, you can hear the sound of

the guitar through the headphones, and the

L

and

R

level

meters move.

NOTE

•

You can use the PAN knob for TRACK 1 on the Mixer screen

to set the stereo position for monitoring.

•

When the REC button for TRACK 1 is unlit, you cannot hear

the guitar sound that is being input.

Recording a guitar to TRACK 1

1. Press the RECORD (0) button to start recording and play

the guitar.

The REC button for TRACK 1 stops flashing and lights

steadily.

2. After you finish your performance, press the STOP (8)

button to stop recording.

The recorded file is saved in the folder of the currently

loaded song.

3. Press the REC button for TRACK 1 so the REC button

becomes unlit.

14

TASCAM DP-24SD

2 - Quick Guide

Playing back the recording

1. To return to the beginning of the song (ZERO point), press

and hold the STOP (8) button and press the REW (m)

(TO ZERO) button (TO ZERO function).

2. Press the PLAY (7) button to play back the recording on

TRACK 1.

3. Use the fader for TRACK 1 and the STEREO fader to adjust

the playback monitoring level. Use the MONITOR LEVEL

knob to adjust the final monitoring volume.

TIP

Use the PAN knob for TRACK 1 on the Mixer screen to set the

stereo position of the track signal.

Recording a guitar to TRACK 2

Now you should listen to the rhythm guitar on TRACK 1 and play

the lead guitar on TRACK 2.

Follow the procedure below to change the recording source of

the TRACK 2.

1. Press the ASSIGN button to open the Assign screen.

Record the lead guitar sound from INPUT H to TRACK 2. By

default, INPUT B is assigned to TRACK 2.

2. Use the CURSOR (5/b/g/t) buttons or press the

SELECT button for TRACK 2 and align the cursor (frame) on

the Assign screen with

TRACK 2

.

Use the JOG/DATA dial or press the SOURCE button for

INPUT H to set the recording source of the TRACK 2 to

H

.

3. Press the HOME button to return to the Home screen.

4. Press the REC button for TRACK 2.

Its REC indicator blinks and the unit enters record standby.

When you play the guitar, the input level is shown by the

level meter for

2

(TRACK 2).

5. Return to the beginning of the song (ZERO point) and start

playback of the recorded rhythm guitar to play the lead

guitar part along with the recording.

Raise the fader for TRACK 2 to hear both the playback of

TRACK 1 and input guitar signal through your headphones.

6. As necessary, use the faders for TRACK 1 and 2, PAN knobs,

STEREO fader and MONITOR LEVEL knob to adjust the

monitoring level and balance.

7. Return to the beginning of the song, press the RECORD (0)

button to start recording, and play the lead guitar part.

The RECORD (0) button lights red, and the REC indicator

for TRACK 2 stops flashing and becomes lit.

8. After you finish your performance, press the STOP (8)

button to stop recording.

The recorded file is saved in the folder of the currently

loaded song.

9. Press the REC button for TRACK 2 so the REC button

becomes unlit.

TASCAM DP-24SD

15

2 - Quick Guide

Recording a vocal to TRACK 3

1. Press the ASSIGN button to open the Assign screen.

2. Use the CURSOR (5/b/g/t) buttons or press the

SELECT button for TRACK 3 and align the cursor (frame) on

the Assign screen with

TRACK 3

.

Use the JOG/DATA dial or press the SOURCE button for

INPUT B to set the recording source of the TRACK 3 to

B

.

3. Press the HOME button to return to the Home screen.

4. Press the REC button for TRACK 3.

The REC indicator blinks and the unit enters record standby.

5. Use the TRIM knob for INPUT B to adjust the input level

suitably for the mic. Set the TRIM knob so that the OL

indicator for INPUT B does not light even when the loudest

sound to be recorded is input.

When you input a sound through an external microphone,

the input level is shown by the

3

level meter.

When you raise the fader for TRACK 3, the STEREO fader and

the MONITOR LEVEL knob, you can hear the sound of the

mic input through the headphones.

NOTE

If the OL indicator continues to light even when the TRIM

knob is turned down, the mic signal itself is too loud. In this

case, move the mic further away from the sound source or

lower the volume of the sound source.

6. Return to the beginning of the song, start playback of the

recorded rhythm guitar and lead guitar parts, and sing along

with the recording.

You can hear the playback of the recorded guitar parts on

tracks 1 and 2 along with the vocal on your headphones.

7. As necessary, use the faders for TRACK 1 and 2, PAN knobs,

STEREO fader and MONITOR LEVEL knob to adjust the

monitoring level and balance.

8. Return to the beginning of the song, press the RECORD

(0) button to start recording, and then sing along with the

recording.

The RECORD (0) button lights red, and the REC indicator

for TRACK 3 stops flashing and lights steadily.

9. After you finish your performance, press the STOP (8)

button to stop recording.

The recorded file is saved in the folder of the currently

loaded song.

10. 1Press the REC button for TRACK 3 so that the REC button

becomes unlit.

16

TASCAM DP-24SD

2 - Quick Guide

Mixing the tracks

Once you have finished your recording, you are ready to mix

down and create a master file.

1. Use the faders for TRACK 1 to 3 to adjust their balance of

levels. Use the STEREO fader to adjust the overall level.

2. Press the MIXER button to open the Mixer screen.

Press the SELECT buttons for TRACK 1 to 3 to select the

track to be set and then use the PAN knob to set its stereo

position.

3. Set the IN point.

The interval from the IN point to the OUT point will be used

for the master file.

Play back the song, press and hold the MARK SET button

and press the IN button at the point where you want to start

the master file.

The position where you pressed the button is set as the IN

point, which is where the mix down will start.

4. Set the OUT point.

Play back the song, press and hold the MARK SET button

and press the OUT button where you want to end the

master file.

The position where you pressed the button is set as the OUT

point, which is where the mix down will end.

TIP

You can also press and hold the MARK SET button and press

the IN or OUT button to set the IN and OUT points when

playback is stopped.

5. Press the MIXDOWN/MASTERING button.

The Recorder mode switches to

Mixdown

mode and the

display returns to the Home screen.

NOTE

In Mixdown mode,

Mixdown

appears on the upper left

corner of the Home screen.

6. Press the RECORD (0) button.

The master file recording starts.

Recording stops automatically when the OUT point is

reached.

NOTE

•

The IN and OUT points must be at least 4 seconds apart. If

the interval is shorter than 4 seconds, the message

I/O

Too Short

will appear and the Recorder mode cannot

switch to

Mixdown

mode .

•

During recording, you can use the track faders to adjust the

levels of the tracks and the overall level.

•

You can also use the equalizer or reverb effect while

recording a master file. (See “Track equalizer” on page 55

and “Send effects” on page 54.)

•

You can mute unwanted tracks so that they are not recorded

to the master file. (See “Muting tracks” on page 39.)

Mastering a recording

You can adjust the master file to tailor the sound to your

preference. This process is called mastering.

8

Checking the master file

1. When Recorder mode is

Mixdown

mode, press the

MIXDOWN/MASTERING button to open the

MASTERING

screen.

The Recorder mode switches to

Mastering

mode and

the display returns to the Home screen.

NOTE

•

In Mastering mode,

Mastering

appears on the upper

left corner of the Home screen.

•

When a master file does not exist, the Recorder mode

cannot switch to

Mastering

mode.

•

If Recorder mode is

Multi Track

mode , you can

press the MIXDOWN/MASTERING button to switch to

the

Mixdown

mode , and then press the MIXDOWN/

MASTERING button again to switch to the

Mastering

mode.

2. In this mode, press the PLAY (7) button to listen to the

master file that you have created.

NOTE

•

Confirm that both the

EQ

and

COMP

items are set to

OFF

. If either is set to

ON

, the sound heard will be affected

by the equalizer and/or compressor. (See “Using the

mastering equalizer” on page 59 and “Using mastering

compression” on page 59.)

•

In

Mastering

mode, the STEREO fader cannot be used

to adjust the level.

TASCAM DP-24SD

17

2 - Quick Guide

8

Applying equalization

In this example, we will use the equalizer on the master file to

reduce high frequencies and increase low frequencies slightly.

1. When Recorder mode is

Mastering

mode, press the F1

(

EQ

) button to open the

EQUALIZER

screen.

2. Turn the EQ HIGH knob to the left to lower the

GAIN

knob

for

HIGH

shown on the screen. Set to "

-2dB

". This reduces

the high frequencies.

3. Next turn the EQ MID knob to the left to lower the

GAIN

for

MID

. Set to "

-2dB

". This reduces the mid frequencies.

4. Next, turn the EQ LOW knob to the right to raise the

GAIN

knob for

LOW

shown on the screen. Set to "

+6dB

". This

increase the low frequencies.

5. Press the ON/OFF button on the right of the LOW knob to

turn the equalizer on.

6. Press the F1 (g) button to return to the Mastering screen.

7. Now you can press the PLAY (7) button to listen to the

master file with equalization.

8

Applying compression

Use the compressor on the master file to adjust the impact of

the entire song.

1. When Recorder mode is

Mastering

mode, press the F2

(

COMP

) button to open the

COMP MULTI

screen.

2. Press the F3 (

LIBRARY

) button to open the library list.

3. Use the JOG/DATA dial to select (blue highlight) an item

from the list and then press the F4 (t) button to load the

appropriate setting from the library.

The library list closes.

TIP

You can also adjust the parameters on the

COMP MULTI

screen using the CURSOR buttons and JOG/DATA dial.

4. Press the F4 (

ON

) button to turn the compressor on.

The indication

OFF

changes to

ON

.

5. Press the F1 (g) button to return to the Mastering screen.

6. Press the PLAY (7) button on the Mastering screen to listen

to the master file with compression.

NOTE

If the

EQ

item is set to

ON

on the

EQUALIZER

screen, the

effect of the equalizer on the sound will also be heard.

18

TASCAM DP-24SD

2 - Quick Guide

8

Normalizing

Normalizing maximizes the volume of the master file.

1. When Recorder mode is

Mastering

mode, press the F4

(

NORM

) button to open the

NORMALIZE

screen.

2. Press the F2 (

YES

) button to perform the normalization.

3. Once the process is completed, the display returns to the

Mastering screen.

8

Re-recording the master file

Re-record the master file with equalization and compression

applied to create a new master file.

1. When Recorder mode is

Mastering

mode, press the

RECORD (0) button.

2. This will record over the master file and create a new master

file with equalization and compression applied.

Shutting down

Turn the unit off when you are done using it.

1. Press the HOME button to open the Home screen.

2. Press and hold the STANDBY/ON button on the rear panel

until

PORTASTUDIO

appears on the display.

When the unit completes its automatic shutdown

procedure, which includes recording various information

about the operations that have been performed until now,

the power turns off (standby).

Always use the procedure above to turn the power off

properly.

CAUTION

When the power is on, do not cut the power to the unit by,

for example disconnecting the power cord. All settings made

since the last time you saved will not be saved. If you cut the

power while an SD card is being accessed, all recorded songs

and data may be damaged and cannot be recovered.

TASCAM DP-24SD

19

3 – Names and Functions of Parts

Top panel

1 GUITAR indicator

This indicator lights when the LINE-GUITAR switch on the

rear panel is set to GUITAR.

2 Display

Use the JOG/DATA dial or the CURSOR (5/b/g/t)

buttons to return to the Home screen, to open the

MENU

screen, to assign input signals to tracks, to change param-

eters for each input or track, and to perform many other

operations.

3 PHANTOM (+48V) button/indicator

Use this button to turn the phantom power on/off for the

MIC/LINE INPUT A-D and E-H jacks on the rear panel.

The PHANTOM indicator lights when phantom power is

turned on.

When the GUITAR indicator is lit, even if phantom (+48V)

power is ON (indicator lit) for E-H, INPUT H will not receive

phantom power.

CAUTION

•

Use the STEREO fader and MONITOR LEVEL knob to lower

the output volume of the unit before turning phantom

power on or off. Depending on the microphone, a loud noise

could occur, damaging equipment and harming people's

hearing.

•

Do not connect or disconnect a microphone when phantom

power is turned on. Doing so could cause a loud noise and

might damage this unit and connected equipment.

•

Turn phantom power on only when using a condenser

microphone that requires phantom power. Turning

phantom power on when a dynamic mic or other mic that

does not require it is connected could damage this unit and

connected equipment.

•

When using condenser mics that require phantom power

and dynamic mics together, be sure to use balanced

dynamic mics. Unbalanced dynamic mics cannot be used

when phantom power is enabled.

•

Supplying phantom power to some ribbon mics will break

them. If you are unsure, do not supply phantom power to a

ribbon mic.

4 OL indicators (A-H)

These indicators light when the input source signal is too

loud.

5 TRIM knobs (A-H)

Use these knobs to adjust the input levels. (See “Making the

first recording” on page 39.)

6 SOURCE buttons/indicators

When you press one of these buttons, the corresponding

input (INPUT A to H) is selected (its button lights) as the

input source.

The mixer and other functions are applied to the selected

input.

These buttons are also used to assign an input source to a

track (see “Assigning inputs” on page 35).

7 MUTE/SOLO indicators

These indicators light when a track is muted or in Solo

mode. When the SOLO button is not lit, it indicates the track

is in Mute mode. When the SOLO button is lit, it indicates

the track is in Solo mode.

20

TASCAM DP-24SD

3 – Names and Functions of Parts

8 REC buttons/indicators

Use these buttons to turn recording on/off for each track.

To monitor a track's input sound through headphones or

a monitoring system, press the REC button for the corre-

sponding track.

When the REC button is turned on, the REC button flashes

when the recorder is stopped, and lights during recording.

9 SELECT buttons/indicators

When you press one of these buttons, the corresponding

track (1 to 23/24) is selected (its button lights) as the current

channel.

The mixer and other functions are applied to the current

channel.

These buttons are also used for the following purposes.

• To assign an input source to a track (See “Assigning

inputs” on page 35.)

• To assign effects to an input (See “Inserting a guitar

effect” on page 53.)

• To select the group for FADER GROUP

0 TRACK faders (TRACK 1 to TRACK 23/24)

Use these faders to adjust the monitoring level of a track's

playback signal or the input signal assigned to the track.

(See “Levels and balance” on page 55.)

q Operation buttons for various functions

Use these buttons to activate/deactivate functions or to

perform the operation set to them.

w FADER GROUP button/indicator

Press this button to set a fader group.

The button becomes lit. (See “Fader group” on page 55.)

e STEREO SELECT button/indicator

When the Assign screen is displayed, you can press this

button to move the cursor from the

TRACK

display to the

STEREO BUS

display, and set the input for the stereo bus.

(See “Assigning to a stereo bus” on page 35.)

r STEREO fader

Use this fader to adjust the stereo signal level output from

the STEREO OUT jacks and PHONES jack. Use this fader

also to adjust the recording level when bouncing or mixing

down tracks.

t REW (m) (TO ZERO) button

When stopped or during playback, press and hold this

button to rewind. Rewind is performed at a fixed 10x speed.

Press briefly to jump to the previous mark.

Press and hold the STOP (8) button and press this button

to locate the beginning of the song (

00:00:00:00

=

ZERO point). (See “Returning to zero or the last recording

position” on page 44.)

y F FWD (,) (TO LAST REC) button

When stopped or during playback, press and hold this

button to fast-forward. Fast-forward is performed at a fixed

10x speed.

Press briefly to jump to the next mark.

Press and hold the STOP (8) button and press this button

to locate the last recording position (LAST REC point). (See

“Returning to zero or the last recording position” on page

44.)

u STOP (8) button

Use this button to stop playback, recording and

fast-forward/rewind. Press at the same time as you press

the REW (m) (TO ZERO) button or F FWD (,) (TO

LAST REC) button to locate the beginning of the song

(

00:00:00:00

= ZERO point) or the last recording

position (LAST REC point). (See “Returning to zero or the last

recording position” on page 44.)

i PLAY (7) button/indicator

Press this button to start playback.

During recording, press this button to stop recording and

start playback (punch out).

During playback or recording, the PLAY (7) button

becomes lit.

o RECORD (0) button/indicator

Press this button to start recording.

This button becomes lit during recording. During playback,

if you press this button when a track REC button is flashing,

recording to that track will begin (punch in). (See “Automatic

punching in and out” on page 46.)

p Color display

3.5-inch TFT LCD display with a resolution of 320x240 dots.

This display shows various types of information.

NOTE

The display is produced with extremely high-precision

manufacturing technologies. More than 99.99% of the

pixels operate to specification. Less than 0.01% of the pixels

may occasionally misfire or appear as red or black dots.

This does not constitute a malfunction.

a GAIN (HIGH/MID/LOW) knobs

Use these knobs to adjust the equalizer gain. (See “Using the

input equalizer” on page 37.)

s FREQ (HIGH/MID/LOW) knobs

Use these knobs to adjust the center frequency of the

equalizer. (See “Using the input equalizer” on page 37.)

d Q knob

Use this knob to adjust the MID bandwidth of the equalizer.

(See “Using the input equalizer” on page 37.)

f EQUALIZER ON/OFF button

Use this button to turn the equalizer on and off. (See “Using

the input equalizer” on page 37.)

g JOG/DATA dial

When the Home screen is displayed, you can use this dial

to perform transport jog operations. (See “Cueing with the

JOG/DATA dial” on page 45.)

Use this dial to change parameter values and select items

when using menus.

La pagina sta caricando ...

Tascam DP-24SD Manuale del proprietario

Tascam DP-24SD Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti