Lutron Electronics LCP128 Guida d'installazione

®

Please Read

Contents

Panel Model Number Guide

LCP128 (LCP) Panels 2

GRAFIK Systems (LP) Panels 3

GRAFIK Systems (CCP) Panels 4

GRAFIK Systems (CCP/LCP) Panels 5

Panel Dimensions

Mini Panel 6

Standard Panel 7

Panel Mounting 8

Wiring/Ratings

System Wiring Overview 9

Feed and Load Wiring Overview 10

Temporary Lighting 10

Ratings 11

Feed Through Panel: Feed and Load Wiring 12

Panel with Main Lugs: Feed Wiring 14

Panel with Main Lugs: Load Wiring 15

Activate Loads in Bypass 16

Complete Installation 17

Remove Bypass Jumpers 17

Warranty 19

Contact Information 20

Installation Guide

LCP128TM (LCP) and

GRAFIK SystemsTM (LP and CCP)

D i m m i n g a n d S w i t c h i n g P a n e l s

Chinese

English Español Français

Português

NederlandsDeutsch

Italiano

LCP Panel shown

Overview

Use this guide to successfully install a dimming and switching panel. This guide describes panel installation,

wiring, and load activation.

®

2 Installation Guide for Dimming and Switching Panels

Panel Model Number Guide

LCP128TM (LCP) (120 V only)

See page 5 for 230 / 220–240 V

Modules:

Quantity and Type

Prefix

Example

L C P - 2 X 2 D 1 A 4 T - 1 2 0 4 M L - 2 0

Prefix

LCP = LCP dimming panel

Module Types

_X _S _D _Q _A _M _F _T

List modules in the order shown above. Insert the

quantity before each module code. Omit codes for

modules not used in panel. See table below for limits

on numbers of modules per panel.

X = Four-Circuit Switching (Relay) (XP)

S = One-Circuit Dimming (1U)

D = Two-Circuit Dimming (2U)

Q = Four-Circuit Dimming (4U)

A = Four-Circuit Adaptive Dimming (4A)

M = Four-Circuit Motor (4M)

F = Four-Circuit Quiet Fan Speed (4FSQ)

T = 0-10 V, DALI (broadcast), DSI, and PWM

Ballast Control (TVM)

Feed Voltage Feed Current

120 for 120 V 20 A or 175 A

Feed

Voltage

Branch Circuit

Breaker Rating

Feed

Type

Feed Type/Input Ratings

FT = Feed-through panel (circuit breakers not included)

/ 120 V

3M or 3ML = 1 phase 3 wire feed (split phase) /

120 / 240 V

4M or 4ML = 3 phase 4 wire feed / 120 / 208 V

Branch Circuit Breaker Rating

Omit for feed-through panels

20 for 20 A branch circuit breakers

Frequency - All Model Numbers and Voltages

50 / 60 Hz

Output (Load) Ratings

Module Type Rating

XP 16 A per circuit

1U, 2U, 4U 16 A per module

4A 16 A per module, 10 A per output

4M 16 A per module, 5 A per output

(1/4 HP motor),

1 motor per output

4FSQ 2 A per output (single ceiling fan)

TVM 50 mA per channel, 750 mA per system

Module Quantity Limits

Panel Size Feed type TVM 4A 4U 4M

Mini Feed-through NA Any combination up to 3 modules

Mini Feed-through 0 to 4 Any combination up to 2 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Mini Breakers NA Any combination up to 3 modules

Mini Breakers 0 to 4 Any combination up to 2 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Feed-through NA Any combination up to 9 modules

Standard Feed-through 0 to 12 Any combination up to 8 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Standard Breakers (main lugs) NA Any combination up to 9 modules

Standard Breakers (main lugs) NA Any combination up to 7 modules

Standard Breakers (main lugs) 0 to 12 Any combination up to 7 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Breakers (main lugs) 0 to 12 Any combination up to 5 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Notes

• ConsultLutronforpanelswithcustombreakerneeds.

• TVM=0isaTVM-readypanel;TVMmodulescaneasilybeinstalledinthefuture.

• TVM=NAisnotTVM-ready

XP

0

®

Installation Guide for Dimming and Switching Panels 3

Example

Panel Model Number Guide (continued)

GRAFIK SystemsTM (LP) (all voltages)

Prefix

L P 7 / 2 8 - 1 2 0 4 M L - 2 0 - C G P _ _ _ _

Prefix

LP = LP dimming panel

Number of Dimming Modules

Indicates number of 4-circuit (4U) dimming modules in the panel: 1 through 8;

also indicates number of full load circuits

Number of Dimming Circuits

Indicates number of dimming circuits in the panel: 4, 8, 12, 16, 20, 24, 28, or 32;

each module has four dimming circuits

Feed Voltage

120 = 120 V

230 = 230 V (CE)

240 = 220 to 240 V (non-CE)

Feed Type Input Ratings

2M or 2ML = 1 phase 2 wire feed 120 V 175 A 50 / 60 Hz

3M or 3ML = 1 phase 3 wire feed (split phase) 120 / 240 V 175 A 50 / 60 Hz

4M or 4ML = 3 phase 4 wire feed 120 / 208 V 175 A 50 / 60 Hz

Mxx = Main Breaker;

xx = breaker size in amps (custom panel option)

IS = 3 phase 4 wire isolation switch (230 / 220 to 240 V only)

Branch Circuit Breaker Rating

20 for 20 A branch circuit breakers (120 V only)

20 A branch circuit breakers have a 16 A continuous load rating

15 for 15 A branch circuit breakers (120 V only)

15 A branch circuit breakers have a 12 A continuous load rating

13 for 13 A branch circuit breakers (230 V CE only)

16 for 16 A branch circuit breakers (220 to 240 V non-CE only)

Custom Panel Suffix (optional)

Indicates panel with special options

Number

of

Dimming

Circuits

Feed

Voltage

Feed

Type

Branch Circuit

Breaker

Rating

Number of

Dimming

Modules

Custom Panel

Suffix

(contact

Lutron for

custom

options)

®

4 Installation Guide for Dimming and Switching Panels

Panel Model Number Guide (continued)

Prefix

CCP = Custom combination panel

Module Types

_X _L _A _M _F _T

List modules in the order shown above. Insert

the quantity before each module code. Omit

codes for modules not used in panel. See table

below for limits on numbers of modules per

panel.

X = Four-Circuit Switching (Relay) (XP)

L = Four-Circuit Dimming (4U)

A = Four-Circuit Adaptive Dimming (4A)

M = Four-Circuit Motor (4M)

F = Four-Circuit Quiet Fan Speed (4FSQ)

T = 0-10 V, DALI (broadcast), DSI, and PWM

Ballast Control (TVM)

Feed Voltage Feed Current

120 for 120 V 15 A or 20 A or 175 A

GRAFIK SystemsTM (CCP) (120 V only)

Example

C C P - 2 X 2 L 1 A 4 T - 1 2 0 4 M L - 2 0 - C G P _ _ _

Module Quantity Limits

Panel Size Feed type TVM 4A 4U 4M

Mini Feed-through NA Any combination up to 3 modules

Mini Feed-through 0 to 4 Any combination up to 2 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Mini Breakers NA Any combination up to 3 modules

Mini Breakers 0 to 4 Any combination up to 2 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Feed-through NA Any combination up to 9 modules

Standard Feed-through 0 to 12 Any combination up to 8 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Standard Breakers (main lugs) NA Any combination up to 9 modules

Standard Breakers (main lugs) NA Any combination up to 7 modules

Standard Breakers (main lugs) 0 to 12 Any combination up to 8 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Breakers (main lugs) 0 to 12 Any combination up to 5 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Notes

• ConsultLutronforpanelswithcustombreakerneeds.

• TVM=0isaTVM-readypanel;TVMmodulescaneasilybeinstalledinthefuture.

• TVM=NAisnotTVM-ready

XP

0

Modules:

Quantity and Type

Prefix Feed

Voltage

Feed

Type

Custom

Panel Suffix

(contact Lutron for custom options)

Branch

Circuit

Breaker

Rating

Feed Type / Input Ratings

FT = Feed-through panel (circuit breakers not included) /

120 V

3M or 3ML = 1 phase 3 wire feed (split phase) / 120 / 240 V

4M or 4ML = 3 phase 4 wire feed / 120 / 208 V

2 = 1 phase 2 wire input breakers (mini only)

3 = 1 phase 3 wire input breakers (mini only)

4 = 3 phase 4 wire input breakers (mini only)

Branch Circuit Breaker Rating

20 = 20 A branch circuit breakers

15 = 15 A branch circuit breakers

Custom Panel Suffix (optional)

Indicates panel with special options

Frequency

(All Model Numbers and Voltages): 50 / 60 Hz

Output (Load) Ratings

Module Type Rating

XP, 4U 16 A per circuit

4A 16 A per module, 10 A per output

4M 16 A per module, 5 A per output

(1/4 HP motor)

4FSQ 2 A per output (single ceiling fan)

TVM 50 mA per channel, 750 mA per system

®

Installation Guide for Dimming and Switching Panels 5

Panel Model Number Guide (continued)

Prefix

CCP = Custom combination panel

Module Types

_X _L _E _A _M _T

List modules in the order shown above. Insert the

quantity before each module code. Omit codes for

modules not used in panel. See table below for limits

on numbers of modules per panel.

X = Four-Circuit Switching (Relay) (XP)

L = Four-Circuit Dimming (4U)

E = Four-Circuit Electronic Low Voltage Dimming (4E)

A = Four-Circuit Adaptive Dimming (4A)

M = Four-Circuit Motor (4M)

T = 0-10 V, DALI (broadcast), DSI, and PWM

Ballast Control (TVM)

Feed Voltage Feed Current

230 = 230 V (CE) 10 A to 125 A

240 = 220 to 240 V (non-CE) 10 A to 125 A

Feed Type

FT = feed-through panel (circuit breakers not included)

4IS = 3 phase 4 wire isolation switch

2M = 1 phase 2 wire input breakers (mini only)

4M = 3 phase 4 wire input breakers (mini only)

GRAFIK SystemsTM (CCP/LCP) (230 / 220 to 240 V only)

Modules:

Quantity

and Type

Prefix

Example

C C P - 1 X 4 L 2 T - 2 3 0 4 I S - C E - L C P - C G P _ _ _

Feed

Voltage

Feed

Type

Custom

Panel Suffix

(contact Lutron for custom options)

Region

Suffix

Region Suffix

CE = 230 V

AU = 220 to 240 V

Note: Should match feed voltage

Controller Type

Omit for single-link circuit selector

2L = 2LinkTM circuit selector

LCP = LCP128TM

Custom Panel Suffix (optional)

Indicates panel with special options

Frequency

(All Model Numbers and Voltages)

50 / 60 Hz

Output (Load) Ratings

Module Type Rating

XP 16 A per circuit

4U (230 V ) 13 A per module, 10 A per output

4U (240 V ) 16 A per module

4A 13 A per module, 8 A per output

4E 16 A per module, 10 A per output

4M 16 A per module, 5 A per output

(1/4 HP motor), 1 motor per output

TVM 50 mA per channel, 750 mA per system

Controller

Type

Module Quantity Limits

Panel Size Feed type TVM 4A 4U 4E 4M

Mini Feed-through NA Any combination up to 3 modules

Mini Feed-through 0 to 4 Any combination up to 2 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Mini Input breakers NA Any combination up to 3 modules

Mini Input breakers 0 to 4 Any combination up to 2 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Feed to through 0 to 12 Any combination up to 8 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Standard Input breakers 0 to 12 Any combination up to 8 modules;

must have 1 4U module minimum;

each 4U module can control only 2 TVM modules

Standard Input breakers 0 to 12 Any combination up to 6 modules; must have 1 4U or XP module

minimum; each 4U or XP module can control only 2 TVM modules

Notes

• ConsultLutronforpanelswithcustombreakerneeds.

• TVM=0isaTVM-readypanel;TVMmodulescaneasilybeinstalledinthefuture.

• TVM=NAisnotTVM-ready

XP

0

®

6 Installation Guide for Dimming and Switching Panels

Panel Dimensions

Mini Panel

Bottom View

Top View

Right SideLeft Side

Dimensions are in inches (mm).

Front View

14.375

(365)

15.875

(403)

8.00

(203)

2.2

(56)

0.15

(4)

4.21

(107)

1.34

(34)

21.50

(546)

24.50

(622)

24.00

(610)

2.21

(56)

15.13

(384)

10.75

(273)

4.09

(104)

Cover

®

Installation Guide for Dimming and Switching Panels 7

Panel Dimensions (continued)

Standard Panel

Bottom View

Top View

Right Side

Dimensions are in inches (mm).

Left Side

Front View

14.375

(365)

15.875

(403)

2.43

(62)

8.00

(203)

4.21

(107)

0.15

(4)

2.69

(68)

41.75

(1060)

59.50

(1511)

59.00

(1499)

2.43

(62)

11.00

(279)

15.125

(394)

4.15

(105)

Cover

®

8 Installation Guide for Dimming and Switching Panels

Panel Mounting

Mounting Guidelines

•ForIndoorUseOnly!NEMA,Type1enclosure,

IP20.

•Panelgeneratesheat.Mountonlywhereambient

temperature is 32 to 104 °F (0 to 40 °C).

•Relativehumiditymustbe<90%non-condensing.

•Reinforcewallstructureforpanelweightandlocal

codes; see table.

•Allow12in(305mm)clearanceaboveandbelow

panel.

•Mountwithin7°oftruevertical.

•Mountpanelwhereaudiblenoiseisacceptable.

(Internal relays click.)

•Mountpanelsoline(mains)voltagewiringis

at least 6 ft (1.8 m) from audio or electronic

equipment and associated wiring.

•Installinaccordancewithallnationalandlocal

electrical codes.

•This equipment is air-cooled. Vents must not be

blocked or you will void the warranty.

•230 V panels with 13 A circuit breakers are

intended for industrial or commercial use only.

1

2

3

4

5

6

7

8

9

Max. Weight w/o

Packaging

Pounds (kg)

No.

Modules

Max. Heat

BTUs (Kcal)/Hr.

Surface Mounting

•Lutronrecommendsusing1/4in(6mm)

mounting bolts (maximum size accepted by

keyholes).

•Reinforcewallstructureasrequiredforweight

and local codes.

•Donotmountpaneldirectlytowallboard/

drywall.

Recess Mounting

•Mounttowallstudbyscrewingthroughslotsin

corners of panel.

•Mountpanelbetweenflushand1/8in(3mm)

below finished wall surface.

Side View:

Surface Mount

Side View:

Recess Mount

Front View

Recommended Mounting Heights*

(for LCP128TM systems)

Mini 45 in (1143 mm)

Standard 25 in (635 mm)

* Measure from floor to bottom of panel;

optimal viewing height for controller.

1

2

4

3

5

6

8

7

A

B

C

N

Load circuit wiring

Feed wiring

Do not

obstruct

vents!

PELV

(Class 2: USA)

Wiring

Air flow

Low-voltage

control

wiring for

TVM loads

90 (22.68)

170 (42.84)

250 (63.00)

330 (83.16)

410 (103.32)

490 (123.48)

570 (143.64)

650 (163.80)

730 (183.96)

24 (11)

35 (16)

37 (17)

68 (25)

71 (26)

74 (27)

77 (28)

80 (29)

83 (30)

LP8/32-1204ML-20 shown

®

Installation Guide for Dimming and Switching Panels 9

System Wiring Overview

A. LCP128TM panel: Refer to the LCP128 Setup and

Operation Manual for detailed wiring information.

B. LP or CCP panel as a part of a GRAFIK Eye®

4000 lighting system: Refer to the GRAFIK Eye 4000

Installation, Setup, and Operation Manual and the system

overview pictured here for detailed wiring information.

C. LP or CCP panel as a part of a GRAFIK

7000TM lighting system: Refer to the GRAFIK 7000

Installation, and Maintenance Guide and the system overview

pictured here for detailed wiring information.

1 2 3 4 D 5 1 2 3 4

Contact closure input

(CCI) 1

Contact closure input

(CCI) 2

Common

Signal

Common

Signal

Common

+24 V

MUX

Drain

Sense

{

Controller Terminals

SELECT CIRCUIT

2

1

Circuit

Data A OK

Power

1 2 3 4 5D

Common

24VFW

MUX

Drain

Sense

1 2 3 4

D

5

B

Comm

Drain

MUX

C

D

Link

A

Link

C

D

Data B OK

Common

MUX

Drain

Note: Single-link circuit

selectors will not have Link B

connector.

Common

+24 V

MUX

Drain

Sense

Circuit Selector Terminals

Incorrect: Branch, T-tap, or

home run not acceptable

Panel

To other panels,

GRAFIK Eye control

units, wallstations, or

control interfaces

Control

interface

GRAFIK

Eye

GRAFIK

Eye

Wallstation

Correct: Daisy chain OK

GRAFIK

Eye

Control

interface

Wallstation

GRAFIK 5000TM,

GRAFIK 6000®, or

GRAFIK 7000TM

panel

Power panel link

Control station device link

Lighting zone controller link

Integration to other devices

Power

panel

Power

panel

®

10 Installation Guide for Dimming and Switching Panels

Wiring (continued)

Feed Wiring (Mains Voltage Wiring)

•Preferredfeedwiringentryforpanelswithmainlugs/isolationswitchisfromthebottomleftofthepanel.

•Preferredfeedwiringentryforfeed-throughpanelsisfromthetoporbottomleftofthepanel,wireddirectly

to module terminal blocks.

•Runwiringsothatline(mains)voltagewiringwillbeatleast6ft(1.8m)fromsoundorelectronicequipment

and its wiring.

•RefertoFeedWiringpagesformoreinformation.

Load Circuit Wiring

•Connectloadwiringtotheappropriateterminalblocksetforeachmodule.

•For230V and 240 V panels, “Hot” is referred to as “Live”. Therefore, terminals will be labeled

DL and L.

•TheDimmedHot/Live(DH/DL)terminalblockisgroupedwithanumberedHot/Live(H/L)(H1,H2,etc./L1,L2,

etc.). The number represents both the module and circuit breaker number.

•Outputterminalblocksacceptone14to10AWG(2.5to4.0mm

2

) wires. Preferred entry is from the top left

of the panel.

•Common neutrals are not permitted. Run separate neutrals for each load circuit.

•RefertoLoadWiringpagesformoreinformation.

Notice: Panels require entry of wires

as specified. Improper entry will block

serviceable parts and impede air flow

through the panel.

Feed and Load Wiring Overview

You do not need to install a temporary distribution

panel. Connect load wires into the appropriate

terminal blocks. Each input breaker can supply

power to a load while the bypass jumper protects

the module from load faults.

Input circuit breaker

Bypass jumper protects the

module from load faults.

Notice: Verify that the panel is fed from the correct

voltage. A feed miswire or loss of a feed neutral

can cause over-voltage damage to the equipment.

Do NOT remove bypass jumpers at this point—they

protect the modules from load faults.

Temporary Lighting

®

Installation Guide for Dimming and Switching Panels 11

Ratings

Number

of

Modules

Feed

Type

Max.

Feed

1

2

3

4

5

6

7

8

9

1Ø 2W

14 to 10 AWG

(2.5 to 4.0 mm

2

)

120 V : 20 A

230 V : 13 A or 16 A

220 to 240 V : 16 A

LP/LCP/CCP Panels

Panels with Breaker

(120 V only)

Number

of

Modules

Feed

Type

1

2

3

1Ø 2W

1Ø 3W

3Ø, 4W

14 to 10 AWG

(2.5 to 4.0 mm

2

)

Panels with Main Lugs

(120 V only)

Number

of

Modules

Feed

Type

Maximum

Feed

4

5

6

7

8

9

1Ø 3W or 3Ø 4W

14 to 2/0 AWG

(2.5 to 70 mm

2

)

175 A

Panels with Breaker

(220 to 240 V and 230 V only)

Number

of

Modules

Feed

Type

1

2

3

1Ø 2W

3Ø 4W

14 to 10 AWG

(2.5 to 4.0 mm

2

)

Panels with Isolation Switch

(220 to 240 V and 230 V only)

Number

of

Modules

Feed

Type

Maximum Feed

230 V 220 to 240 V

4

5

6

7

8

3Ø 4W

14 to 2/0 AWG

(2.5 to 70 mm

2

)

125 A 125 A

Feed-Through Panels

(all voltages)

®

12 Installation Guide for Dimming and Switching Panels

Feed-Through Panel: Feed and Load Wiring (all voltages)

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

To distribution

panel

Load

Hot/live

Switched

hot/live

4-Circuit Switching (Relay) Module (XP)

Bypass jumper

Feed

N

DH

H

DH

N

DH

N

Dimmed hot/live

Hot/Live

Neutral

Load

4-Circuit Dimming Module (4U)

4-Circuit Adaptive Dimming Module (4A)

4-Circuit ELV Dimming Module (4E: 230 V and 220 to 240 V only)

4-Circuit Quiet Fan Speed Module (4FSQ)

Bypass jumper

Feed

General Notes

•Typicaldimming/switchinglegsshown.

•Donotremovebypassjumpersuntilafterloadwiringhasbeen

verified.

Wire sizes for power feed, to each input

•Powerfeed:14to10AWG(2.5to4.0mm

2

)

•Neutralfeed:14to10AWG(2.5to4.0mm

2

)

Wire sizes for load wiring, from each output

•Dimmedhot(live):14to10AWG(2.5to4.0mm

2

)

•Loadneutral:14to10AWG(2.5to4.0mm

2

)

Control Circuit Power

•Suppliespowerforinternaloperation.

•Requiresdedicatedfeedwithsamevoltageandphaseaspanel.

•Mustbe1/4in(6mm)awayfromPELV(Class2:USA)controlwiring

harness.

•Panelvoltage(seepages2to3)indicatesfeedvoltage.

•For230V and 240 V panels, “Hot” is referred to as “Live”.

Therefore, terminals will be labeled L and DL.

See terminal

block modules

for specific wiring

details.

Bypass jumper

Feed

Neutral

Hot/Live

TVM Module

For 0-10 V, PWM, Tridonic® DSI, and DALI loads. Each

TVM controls two consecutive circuits of lighting and

are the first circuits in the panel. Maximum low-voltage

ballastcontrolcurrent:50mAperzone,750mAperpanel.

Dimming or switching module is used to switch power to

the ballast.

+ 1 –

+ 2 –

N

H/L

+

–

N

DH

H

DH

N

DH

N

Ballast

Neutral

Dimmed hot/live

TVM

Circuit breaker

Neutral

®

Installation Guide for Dimming and Switching Panels 13

Feed-Through Panel: Feed and Load Wiring (continued)

Bypass jumper

N

DH

H

Dimmed hot/live

Neutral

Load

1-Circuit Dimming Module (1U)

(LCP only)

Bypass

jumper

Hot/Live

Feed

Neutral

N

DH

H

DH

N

Feed

Dimmed hot/live

Neutral

Load

2-Circuit Dimming Module (2U)

(LCP only)

Bypass jumper

Neutral

Hot/Live

N

L

H

R

N

L

R

N

L

R

L

R

Lower

Neutral

Hot/Live

Neutral

4-Circuit Motor Module (4M)

Feed

Raise

Hot/Live

Feed

Neutral

Hot/

Live

N

DH

H

DH

N

DH

N

Connecting an NGRX-FDBI to a Panel

Load

Lutron®

Eco-10® or

Hi-lume®

FDB ballast

Dimmed

hot/live

Lutron®

FDBI

Feed

Refer to FDBI Installation

Sheet for detailed wiring.

Circuit breaker

Circuit

breaker

Circuit breaker

®

14 Installation Guide for Dimming and Switching Panels

Panel with Main Lugs: Feed Wiring

Neutral

Power (hot/live)

Feed wiring

Prewired to circuit

breakers

Prewired neutral to

dimming modules

Phase A

N

Main lugs in panel

Phase B

Phase C

Phase A

N

Phase B

Phase C

Neutral

Neutral bus

Power (hot/live)

Feed wiring

Dimming and Switching Panels

(120 V only)

Dimming Panels

(120 V only)

Ground bar

Breakers

N

Feed wiring

Notes

•See page 15 for load wiring details.

• On dimming panels only, the input breaker

of Circuit 1 supplies current to Load Circuit

1 and to the Control Wiring (2 A draw

max.). Panels with switching modules have

a dedicated circuit breaker for the control

circuit.

Neutral

Power (hot/live)

Main Lugs feed wiring gauge:

2/0 AWG (70 mm

2

)

Mini Panel Breaker Wiring

(all voltages)

Feed wiring

Neutral

Power (hot/live)

Dimming Panels

Isolation Switch

(230 / 220 to 240 V )

®

Installation Guide for Dimming and Switching Panels 15

Panel with Main Lugs: Load Wiring

N

DH

H

N

DH

H

DH

N

DH

H

DH

N

DH

N

L

H

R

N

L

R

N

L

R

L

R

H

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

Raise

Lower

Neutral

4-Circuit Motor Module (4M)

N

DH

H

N

DH

H

DH

N

DH

H

DH

N

DH

N

L

H

R

N

L

R

N

L

R

L

R

H

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

Dimmed hot/live

Neutral

Load

1-Circuit Dimming Module (1U)

(LCP only)

Bypass jumper

N

DH

H

N

DH

H

DH

N

DH

H

DH

N

DH

N

L

H

R

N

L

R

N

L

R

L

R

H

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

Dimmed hot/live

Neutral

Load

2-Circuit Dimming Module (2U)

(LCP only)

Bypass jumper

N

DH

H

N

DH

H

DH

N

DH

H

DH

N

DH

N

L

H

R

N

L

R

N

L

R

L

R

H

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

Dimmed hot/live

Neutral

Load

4-Circuit Dimming Module (4U)

4-Circuit Adaptive Dimming Module (4A)

4-Circuit ELV Dimming Module

(4E: 230 V and 220 to 240 V only)

4-Circuit Fan Speed Control Module (4FSQ)

Bypass jumper

N

DH

H

N

DH

H

DH

N

DH

H

DH

N

DH

N

L

H

R

N

L

R

N

L

R

L

R

H

N

H1

SH1

H2

SH2

H3

SH3

H4

SH4

Neutral

Load

Switched

hot/live

4-Circuit Switching Module (XP)

Bypass jumper

Notice: Do not remove bypass jumpers until after

load wiring has been verified.

Typical Dimming/Switching Leg Shown

Load Wiring for TVM Module

For 0-10 V, PWM, and Tridonic® DSI loads. Each

TVM controls two consecutive circuits of lighting

and are the first circuits in the panel. Maximum

low-voltage ballast control current:

50mAperzone,750mAperpanel.

+ 1 –

+ 2 –

N

H/L

+

–

N

DH

H

DH

N

DH

N

Ballast

Neutral

Dimmed

hot/live

TVM

Bypass jumper

N

DH

H

DH

N

DH

N

Connecting an NGRX-FDBI to a Panel

For Hi-lume® FDB or Eco-10® Fluorescent Dimming Ballast

Load

Lutron®

Eco-10 or

Hi-lume

FDB ballast

Neutral

Dimmed

hot/live

Lutron®

FDBI

Feed

Bypass jumper

Shade

®

16 Installation Guide for Dimming and Switching Panels

Activate Loads in Bypass

DH

H

N

DH

H

1

2

N

A. Complete load wiring.

B. Check that the bypass jumpers are in place.

These jumpers protect from load faults and

must be used to check load wiring when it is

installed or modified.

Notice: Verify that the panel is fed from

the correct voltage. A feed miswire or loss

of a feed neutral can cause damage to the

equipment.

C. Turn circuit breaker 1 ON.

The load(s) should energize, the breaker

should not trip, and total load current must be

within the circuit breaker’s limit and less than

or equivalent to 16 A.

Circuit breaker 1 powers the control wiring as

well as Circuit 1’s dimmer and load(s). Check

that the Power OK LED on the Controller

(LCP128TM) or circuit selector (LP or CCP) is

ON. If the Power OK LED is OFF, turn OFF the

control circuit breaker (breaker 1) and check

for a miswire on the low voltage link.

D. Turn next circuit breaker ON.

The load should energize, the breaker should

not trip, and total load current must be within

the circuit breaker’s limit and less than or

equal to 16 A.

E. Repeat step D for each circuit with completed

load wiring.

AC RMS current

Bypass jumper

Load circuit wiring

‘Power OK’ LED

at the bottom of LCP128 Controller

‘Power OK’ LED

at the top of LP/CCP Circuit Selector

Activate Loads in Bypass

LCP-8D-1204ML-20 shown

LP3/12-1204ML-20 shown

®

Installation Guide for Dimming and Switching Panels 17

A. After all load wiring has been checked, turn

circuit breakers OFF.

B. Remove and store the bypass jumpers for

possible future use.

C. Turn circuit breakers ON.

All circuits are now set to the default Non-Dim

load type. Non-Dim load types will respond

by immediately going to full ON in any lighting

scene (except the OFF scene).

Notice: Reuse the bypass jumpers whenever

work is being done on a load. Damage caused

by short-circuits and miswiring is not covered

by the product warranty.

Panel installation, control station wiring, and load activation are now complete.

Next Step: Refer to the Setup and Operation Manual to set up the functions and operation of the panel.

DH

H

N

Bypass jumper

Module with 4 outputs shown

Complete Installation

Remove Bypass Jumpers

You have completed your panel installation.

For Onsite Factory Commissioning, call Lutron Technical Support and select Startup to schedule a field

service visit. Allow for 10 working days between day of call and scheduled visit.

If you purchased Telephone Startup (LCP128TM only), stop here and complete the Control Location, Panel,

and Control Station Tables that are located in the back of the Setup and Operation Manual. Once the tables

are complete, call Lutron Technical Support and select Startup. Please call 24 hours prior to desired system

startup.

In the U.S., Canada, and the Caribbean: 1.800.523.9466

In Mexico: +1.888.235.2910

In Europe: +44.(0)20.7702.0657

In Asia: +65.6220.4666

In Japan: +81.3.5575.8411

In all other countries: +1.610.282.6701

®

18 Installation Guide for Dimming and Switching Panels

Notes

®

Installation Guide for Dimming and Switching Panels 19

Warranty

Lutron Electronics Co., Inc.

One Year Limited Warranty

For a period of one year from the date of purchase, and subject to the exclusions and restrictions described below, Lutron

warrants each new unit to be free from manufacturing defects. Lutron will, at its option, either repair the defective unit or

issue a credit equal to the purchase price of the defective unit to the Customer against the purchase price of comparable

replacement part purchased from Lutron. Replacements for the unit provided by Lutron or, at its sole discretion, an approved

vendor may be new, used, repaired, reconditioned, and/or made by a different manufacturer.

If the unit is commissioned by Lutron or a Lutron approved third party as part of a Lutron commissioned lighting control

system, the term of this warranty will be extended, and any credits against the cost of replacement parts will be prorated, in

accordance with the warranty issued with the commissioned system, except that the term of the unit’s warranty term will be

measured from the date of its commissioning.

EXCLUSIONS AND RESTRICTIONS

This Warranty does not cover, and Lutron and its suppliers are not responsible for:

1. Damage, malfunction or inoperability diagnosed by Lutron or a Lutron approved third party as caused by normal wear

and tear, abuse, misuse, incorrect installation, neglect, accident, interference or environmental factors, such as (a) use of

incorrect line voltages, fuses or circuit breakers; (b) failure to install, maintain and operate the unit pursuant to the operating

instructions provided by Lutron and the applicable provisions of the National Electrical Code and of the Safety Standards

of Underwriter’s Laboratories; (c) use of incompatible devices or accessories; (d) improper or insufficient ventilation;

(e) unauthorized repairs or adjustments; (f) vandalism; or (g) an act of God, such as fire, lightning, flooding, tornado,

earthquake, hurricane or other problems beyond Lutron’s control.

2. On-site labor costs to diagnose issues with, and to remove, repair, replace, adjust, reinstall and/or reprogram the unit or any

of its components.

3. Equipment and parts external to the unit, including those sold or supplied by Lutron (which may be covered by a separate

warranty).

4. The cost of repairing or replacing other property that is damaged when the unit does not work properly, even if the damage

was caused by the unit.

EXCEPT AS EXPRESSLY PROVIDED IN THIS WARRANTY, THERE ARE NO EXPRESS OR IMPLIED WARRANTIES OF

ANY TYPE, INCLUDING ANY IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.

LUTRON DOES NOT WARRANT THAT THE UNIT WILL OPERATE WITHOUT INTERRUPTION OR BE ERROR FREE.

NO LUTRON AGENT, EMPLOYEE OR REPRESENTATIVE HAS ANY AUTHORITY TO BIND LUTRON TO ANY

AFFIRMATION, REPRESENTATION OR WARRANTY CONCERNING THE UNIT. UNLESS AN AFFIRMATION,

REPRESENTATION OR WARRANTY MADE BY AN AGENT, EMPLOYEE OR REPRESENTATIVE IS SPECIFICALLY INCLUDED

HEREIN, OR IN STANDARD PRINTED MATERIALS PROVIDED BY LUTRON, IT DOES NOT FORM A PART OF THE BASIS OF

ANY BARGAIN BETWEEN LUTRON AND CUSTOMER AND WILL NOT IN ANY WAY BE ENFORCEABLE BY CUSTOMER.

IN NO EVENT WILL LUTRON OR ANY OTHER PARTY BE LIABLE FOR EXEMPLARY, CONSEQUENTIAL, INCIDENTAL

OR SPECIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF PROFITS, CONFIDENTIAL OR

OTHER INFORMATION, OR PRIVACY; BUSINESS INTERRUPTION; PERSONAL INJURY; FAILURE TO MEET ANY DUTY,

INCLUDING OF GOOD FAITH OR OF REASONABLE CARE; NEGLIGENCE, OR ANY OTHER PECUNIARY OR OTHER

LOSS WHATSOEVER), NOR FOR ANY REPAIR WORK UNDERTAKEN WITHOUT LUTRON’S WRITTEN CONSENT ARISING

OUT OF OR IN ANY WAY RELATED TO THE INSTALLATION, DEINSTALLATION, USE OF OR INABILITY TO USE THE

UNIT OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF THIS WARRANTY, OR ANY AGREEMENT

INCORPORATING THIS WARRANTY, EVEN IN THE EVENT OF THE FAULT, TORT (INCLUDING NEGLIGENCE), STRICT

LIABILITY, BREACH OF CONTRACT OR BREACH OF WARRANTY OF LUTRON OR ANY SUPPLIER, AND EVEN IF LUTRON

OR ANY OTHER PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

NOTWITHSTANDING ANY DAMAGES THAT CUSTOMER MIGHT INCUR FOR ANY REASON WHATSOEVER (INCLUDING,

WITHOUT LIMITATION, ALL DIRECT DAMAGES AND ALL DAMAGES LISTED ABOVE), THE ENTIRE LIABILITY OF

LUTRON AND OF ALL OTHER PARTIES UNDER THIS WARRANTY ON ANY CLAIM FOR DAMAGES ARISING OUT OF

OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, USE, REPAIR, OR REPLACEMENT

OF THE UNIT, OR ANY AGREEMENT INCORPORATING THIS WARRANTY, AND CUSTOMER’S SOLE REMEDY FOR THE

FOREGOING, WILL BE LIMITED TO THE AMOUNT PAID TO LUTRON BY CUSTOMER FOR THE UNIT. THE FOREGOING

LIMITATIONS, EXCLUSIONS AND DISCLAIMERS WILL APPLY TO THE MAXIMUM EXTENT ALLOWED BY APPLICABLE LAW,

EVEN IF ANY REMEDY FAILS ITS ESSENTIAL PURPOSE.

TO MAKE A WARRANTY CLAIM

To make a warranty claim, promptly notify Lutron within the warranty period described above by calling the Lutron Technical

Support Center at (800) 523-9466. Lutron, in its sole discretion, will determine what action, if any, is required under this

warranty. To better enable Lutron to address a warranty claim, have the unit’s serial and model numbers available when

making the call. If Lutron, in its sole discretion, determines that an on-site visit or other remedial action is necessary, Lutron

may send a Lutron Services Co. representative or coordinate the dispatch of a representative from a Lutron approved vendor

to Customer’s site, and/or coordinate a warranty service call between Customer and a Lutron approved vendor.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some

states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may

not apply to you.

Tridonic is a registered trademark of Zumtobel Aktiengesellschaft.

Lutron, the sunburst logo, GRAFIK Eye, GRAFIK 6000, Eco-10, and Hi-lume are reg is tered trademarks, and LCP128,

GRAFIK Systems, GRAFIK 5000, GRAFIK 7000, and 2Link are trademarks of Lutron Electronics Co., Inc.

Contact Information

®

Lutron Electronics Co., Inc.

Made and printed in U.S.A.

P/N 032-342 Rev. A 12.15.10

Internet: www.lutron.com

E-mail: [email protected]

WORLD HEADQUARTERS

USA

Lutron Electronics Co., Inc.

7200 Suter Road, Coopersburg, PA 18036-1299

TEL +1.610.282.3800

FAX +1.610.282.1243

Toll-Free 1.888.LUTRON1

Technical Support 1.800.523.9466

North and South America Technical Hotlines

USA, Canada, Caribbean: 1.800.523.9466

Mexico: +1.888.235.2910

Central/South America: +1.610.282.6701

EUROPEAN HEADQUARTERS

United Kingdom

Lutron EA Ltd.

6 Sovereign Close, London, E1W 3JF United Kingdom

TEL +44.(0)20.7702.0657

FAX +44.(0)20.7480.6899

FREEPHONE (UK) 0800.282.107

Technical support +44.(0)20.7680.4481

ASIAN HEADQUARTERS

Singapore

Lutron GL Ltd.

15 Hoe Chiang Road, #07-03 Tower 15, Singapore 089316

TEL +65.6220.4666

FAX +65.6220.4333

Technical support +800.120.4491

Asia Technical Hotlines

Northern China: 10.800.712.1536

Southern China: 10.800.120.1536

Hong Kong: 800.901.849

Japan: +81.3.5575.8411

Macau: 0800.401

Singapore: 800.120.4491

Taiwan: 00.801.137.737

Thailand: 001.800.120.665853

Other countries: +65.6220.4666

La pagina sta caricando ...

Lutron Electronics LCP128 Guida d'installazione

Lutron Electronics LCP128 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti