ProLights ECLFR2KTW Manuale utente
- Categoria
- Stroboscopi
- Tipo
- Manuale utente
USER MANUAL
MANUALE UTENTE
ECLFR2KTW
EN - IT
FRESNEL PROJECTOR
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV.01-05/19
1
ECLFR2KTW
Packing content
• ECLFR2KTW
• ECLFR2KTPG
• ECLFR2KBD
• ECLFRSPG
• Power cable
• User manual
TABLE OF
CONTENTS
Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description and specifications
1. 2 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 DMX addressing
3. 5 DMX configuration
3. 6 Linking
3. 7 Screen
3. 8 Advanced
3. 9 Information
3. 10 Master/Slave mode
3. 11 Effects mode
3. 12 Fixed color
3. 13 Manual mode
3. 14 DMX control
3. 15 Connection of the DMX line
3. 16 Construction of the DMX termination
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Trouble shooting
2
2
3
5
6
7
7
8
11
11
11
12
12
13
13
13
14
14
15
22
22
23
23
ECLFR2KTW
2
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modifications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system fitted with efficient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualified electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the fixture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 45 °C.
• Make certain that no inflammable liquids, water or metal objects enter the fixture.
• Do not dismantle or modify the fixture.
• All work must always be carried out by qualified technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation definitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way different to the one described in this manual, it may suffer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
• Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
• Install the fixture in a well ventilated place.
• Keep any inflammable material at a safe distance from the fixture.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their effectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot.
• This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
• We decline any liability deriving from improper use of the product.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
3
ECLFR2KTW
- 1 - INTRODUCTION
1.1 DESCRIPTION
ECLFR2KTW is an advanced LED replacement of traditional 2K Fresnel lamps. Offering 6 colour mixing,
delivering high precision reproduction of the white spectrum from 2.800 K to 10.000 K with high CRI and
extensive colour reproduction.
The optical system harnesses the power of a 507 W custom LED with 6 colours to create an even projec-
tion, beautiful colours and precise whites, with the option to apply +/- green and magenta correction to
match other light sources.
Featuring HD dimming and tuning from 2.800 K to 10.000 K, the ECLFR2KTW delivers both on perfor-
mance and quality of output that is demanded from this level of light.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
• Source: 507W 6 colour custom LEDs source (red, orange, green, royal blue, blue, lime)
• CT: 2.800 K - 10.000K
• CRI: > 91
• R9: > 96
• Luminous flux: (16°) 10’720 - (52°) 14’051lm
• Lux: (16°) 11’600 lx - (52°) 2’200lx @3 m full
• Lux: (16°) 4’176 lx - (52°) 793lx @5 m full
• Source life expectancy: >70.000 h
• Other: TM30-15RF: 88 / 107 - TLCI: 90,8
OPTICS
• Zoom: 16° - 52° manual
• Lens diameter: 250mm
• Lens type: fresnel zoom lens
• Other: spigot, barn door and gel frame included
COLOUR SYSTEM
• Colour mixing: 6 colour custom LEDs source (red, orange, green, royal blue, blue, lime)
• CTC: CTC control through independent DMX channel, + / - green and magenta correction and amber
shift activation by DMX
• White presets: 2.800 K - 10.000K
• Colour wheel: virtual colour wheel with presets
• Macros: several pre-build macros with adjustable speed
DYNAMIC EFFECTS
• Static colour mode: selection of static colour
• Manual colour mode: manual adjustment of intensity, CT, colour correction from knob
• Auto mode: built-in programs with execution speed adjustment
• Special features: linear crossfade from a white to any color and CTO applied on colours
BODY
• Hardware on-board: included filter frame, 8 doors barndoor, omega bracket spigot
• Body: sturdy die-cast aluminium body conceived for long-time durability
• Body colour: black
CONTROL
• Protocols: DMX512, RDM, local knob
• DMX channels: 1 / 2 / 5 - 1 / 5 - 2 / 7 - 1 / 7 - 2 / 8 / 9 / 12 / 13 / 16 / 19 / 21channel
ECLFR2KTW
4
• RDM: RDM ready for fixture remote monitor and settings
• Display: black OLED high resolution display
• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included
• Master/Slave: for synchronized operation of more units linked in a chain
• Other: 16bit control of dimmer and colour
ELECTRONICS
• Dimmer: linear 0 ~ 100% electronic dimmer
• Dimmer curves: 4 different dimming curves available
• Strobe / shutter: 1 - 30 Hz, electronic
• Operating temperature: -10° ~ +45°
• Flicker: flicker free frequency with adjustable PWM
• Selectable PWM: 600 ~ 25.000 Hz
ELECTRICAL
• Power consumption:
• Power supply: 100-240 V – 50/60 Hz
• Power consumption (at 230 V): 393W
• Power consumption (at 120 V): 386W
• Output (at 230 V): 5 units on a single power line
• Output (at 120 V): 2 units on a single power line
• Power factor: pF 0,95 @230 V - pF 0,99 @120 V
PHYSICAL
• Cooling: combination of heat pipe cooling system and low noise fan
• Sospension and fixing: hanging bracket suitable for safe hanging and positioning
• Signal connection: Amphenol XLR 5p IN/OUT connectors
• Power connection: Neutrik powerCON TRUE1 IN/OUT connectors
• IP rating: 20
• Dimensions (WxHxD): 421x537x455mm
• Weight: 15,8kg
Technical drawing Fig.1
455
421
537
Rear panel
5
ECLFR2KTW
1.2 OPERATING ELEMENTS AND CONNECTIONS
3
4
5
98
12
13
14
10
15
11
2
1
6
7
Fig.2
1. AIR GRID for air flow outlet not to be
obstructed.
2. KNOB for inclination adjustment.
3. HANDLE
4. MOUNTING BRACKET
5. SPIGOT
6. CONTROL PANEL with display and 4 button
used to access the control panel functions
and manage them.
7. ZOOM ADJUSTMENT KNOB AND FOCUS to
zoom the projected image clearly.
8. GEL FILTER FRAME
9. BARN DOOR with directional flaps to adjust
the light beam.
10. HOLDER for locking and releasing accessories
11. MAIN FUSE HOLDER: replace a burnt-out fuse by
one of the same type only
12. POWER IN (PowerCON TRUE IN): for connection
to a socket (100-240V~/50-60Hz) via the supplied
mains cable.
13. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =
DMX+, 4 N/C, 5 N/C.
14. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3 =
DMX+, 4 N/C, 5 N/C.
15. POWER OUT (PowerCON TRUE OUT): power
output for connection of multiple units in series.
ECLFR2KTW
6
Fig.4
CLAMP
- 2 - INSTALLATION
2.1 MOUNTING
ECLFR2KTW is designed for applications in exhibition areas, commercial spaces, museums, restaurant,
churches, and any other installation where size is an important factor. For fixing, stable mounting clips are
required. The mounting place must be of sufficient stability and be able to support a weight of 10 times
of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
garding safety) currently in force in the country in which the fixture’s being used.
• Install the projector at a suitable location.
• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-
ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The
adjust the projector and use the knobs.
NOTE - For the installation of the ECLFR2KTW make sure that the ridge of the adaptor is in with the groove
of the track. Turn knobs 90° to connect the adaptor to the circuit. Please see the figure 4.
7
ECLFR2KTW
MENU
UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in
a function
Used to select and store the
current menu or confirm the
current function value or
option within a menu
Fig.5
Menu
Enter
Up
Down
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
To turn ECLFR2KTW connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit
is ready for operation and can be operated via a DMX controller. To switch off, disconnect the mains plug
from the socket. For a more convenient operation it is recommended to connect the unit to a socket which
can be switched on and off via a light switch.
3.2 BASIC
The ECLFR2KTW has a display and 4 button for access to the control panel functions (fig.5).
MODE LEFT KNOB
CENTRAL KNOB RIGHT KNOB
CCT Dimmer (0 - 255) +/- Green (-25-+25) Control temperature
(CT): 2800 K - 10000 K
HSI Dimmer (0 - 255) Colors (0 - 255) Saturation (SAT): 0 - 255
MENU
1 CONNECT
ð
DMX Address
ð
Value (001-512)
Default: 1
DMX Mode
ð
1CH
ð
Amber Shift on
Default: 19CH
ð
Color
Temperature
ð
CTO 2800 - 10000K
Hue (025~025)
ð
Color Picker
ð
3200K
71
97
100
...
777
ð
Customization
ð
Red (000~255)
Orange (000~255)
Green (000~255)
Royal Blue (000~255)
Blue (000~255)
Lime (000~255)
ð
2CH
ð
Amber Shift on
ð
Color
Temperature
ð
CTO 2800 - 10000K
Hue (025~025)
ð
Color Picker
ð
3200K
71
97
100
...
777
ð
Customization
ð
Red (000~255)
Orange (000~255)
Green (000~255)
Royal Blue (000~255)
Blue (000~255)
Lime (000~255)
ð
5CH1
ð
Color Picker
ð
5CH2
ð
7CH1
ð
7CH2
ð
No Action
3200K
71
97
100
...
777
ð
8CH
ð
9CH
ð
12CH
ð
13CH
ð
16CH
ð
19CH
ð
21CH
2 SETUP
ð
Screen
ð
Back Light
ð
On
10 s
20 s
30 s
Default: 10 s
ð
Flip Display
ð
NO-Yes Default: No
ð
Key Lock
ð
NO-Yes Default: No
ECLFR2KTW
8
3.3 MENU STRUCTURE
3 ADVANCED
ð
Full On Mode
ð
HB
Studio
Default: Studio
Dimmer Mode
ð
Off
Dimmer 1
Dimmer 2
Dimmer 3
Default: Off
White Balance
ð
Off
Adjust
ð
Red (125~255)
Orange (125~255)
Green (125~255)
Royal Blue (125~255)
Blue (125~255)
Lime (125~255)
Default: Off
Led Frequency
ð
600Hz
1200 Hz
2000 Hz
4000 Hz
6000Hz
25kHZ
Default: 1200Hz
Fan Mode
ð
Auto
On
Off
Silent
Default : Auto
Factory Reload
ð
No-Yes No-Yes Default: No
4 INFORMATION
ð
Fixture TIme
ð
0-9999
Version
ð
V1.0
UID
ð
15D00229****
5 STAND ALONE
ð
Master/Slave
ð
Master
Slave
Default : Slave
Effects
ð
Effect1
Effect2
Effect3
Effect4
ð
(1~100) Default: Effect4
Speed=100
CCT
HSI
Color Tempera-
ture
ð
2800K
3000K
3200K
3400K
3600K
3800K
4000K
4200K
4400K
4600K
4800K
5000K
5200K
5400K
5600K
5800K
6000K
6200K
6400K
6800K
7000K
7200K
7400K
7600K
7800K
8000K
8200K
8400K
8600K
8800K
9000K
9200K
9400K
9600K
9800K
10000K
ð
Dimmer (000~255)
Hue (025~025)
Default : 6000K
Dimmer=255
Hue=0
9
ECLFR2KTW
Fixed Color
ð
R
O
G
RB
B
L
R.0
R.G
R.RB
R.B
R.L
O.G
O.RB
O.B
O.L
G.RB
G.B
G.L
RB.B
RB.L
B.L
R.O.G
R.O.RB
R.O.B
R.O.L
R.G.RB
R.G.B
R.G.L
R.RB.B
R.RB.L
R.B.L
O.G.RB
O.G.B
O.G.L
O.RB.B
O.RB.L
O.B.L
G.RB.B
G.RB.L
G.B.L
RB.B.L
R.O.G.RB
R.O.G.B
R.O.G.L
R.O.RB.B
R.O.RB.L
R.O.B.L
R.G.RB.B
R.G.RB.L
R.G.B.L
R.RB.B.L
O.G.RB.B
O.G.RB.L
O.G.B.L
O.RB.B.L
G.RB.B.L
R.O.G.RB.B
R.O.G.RB.L
R.O.G.B.L
R.O.RB.B.L
R.G.RB.B.L
O.G.RB.B.L
R.O.G.RB.B.L
ð
Dimmer (000~255) Default:
R.O.G.RB.B.L
Dimmer=255
Color Picker
ð
3200K
71
97
100
101
102
103
104
105
106
107
110
111
113
115
116
117
118
119
120
121
122
124
126
128
130
132
134
135
136
137
138
139
141
144
147
151
152
156
157
158
161
164
165
166
170
174
179
180
181
182
195
197
198
200
201
202
203
204
205
206
702
730
777
ð
Dimmer (000~255) Default: 3200K
Manual Color
ð
Red
Orange
Green
Royal Blue
Blue
Lime
ð
(000~255) Default:
RGBW=255
ECLFR2KTW
10
11
ECLFR2KTW
3.4 DMX ADDRESSING
To set DMX addressing follow the instructions below:
• Press the button MENU to enter the menu mode.
• Press UP/DOWN button to select Connect. Press the ENTER button to confirm.
• Press UP/DOWN button to select DMX Address. Press the ENTER button to confirm.
• Press UP/DOWN button to select the desired value 001-512. Press the ENTER button to confirm.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
To able to operate the ECLFR2KTW with a light controller, adjust the DMX start address for the first a
DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX
channel, adjust the start address 33 on the ECLFR2KTW. The other functions of the light effect panel are
then automatically assigned to the following addresses.
3.5 DMX CONFIGURATION
The ECLFR2KTW has different DMX channels configurations available selectable through the control panel.
• Press the button MENU to enter the menu mode.
• Press UP/DOWN button to select Connect. Press the ENTER button to confirm.
• Press UP/DOWN button to select DMX mode. Then press the ENTER button to confirm.
• Press UP/DOWN button to select the desired configuration (1CH, 2CH 2, 5CH1, 5CH2, 7CH1, 7CH2, 8CH , 12CH ,
13CH, 16CH, 19CH, 21CH); then press the ENTER button to save.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
The tables on page 15, 16, 17, 18, 19, 20, 21 indicate the operating mode and DMX value. The ECLFR2KTW
is equipped with 5-pole XLR connections.
3.6 LINKING
Several units may be interconnected; follow the instructions below:
1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the first slave unit.
2. Connect the DMX OUT of the first slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last fixture (see page 22).
. . . . . . . . . . . .
DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43
Fig.5 - Example 5 DMX channels configuration
. . . . . . . . . . . .
DMX512 Controller
ECLFR2KTW
12
Numero
canali DMX
Indirizzo di
start (esempio)
Indirizzo DMX
occupati
Prossimo indirizzo di start
possibile per unità n°1
Prossimo indirizzo di start
possibile per unità n°2
Prossimo indirizzo di start
possibile per unità n°3
1 33 33 34 35 36
2 33 33-34 35 37 39
5 33 33 - 37 38 43 48
7 33 33 - 39 40 47 54
8 33 33 - 40 41 49 57
9 33 33 - 41 42 51 60
12 33 33 - 44 45 57 69
13 33 33 - 45 46 59 72
16 33 33 - 48 49 65 81
19 33 33 - 51 52 71 90
21 33 33 - 53 54 75 96
3.7 SCREEN
It is possible to modify the following parameters, related to the display, following the same procedure:
• Press the button MENU to enter the menu mode.
• Press UP/DOWN button to scroll through the menu, select Set Up, then press the ENTER button to access
the next menu.
• Press UP/DOWN button to select Screen and press the ENTER button to proceed.
• Select the proposed option and press the ENTER button to confirm.
- Backlight - Auto Off display backlight. This function allows you to switch off automatically the back-
lighting of the display after a certain time which can be set using the directional keys. To have the
display always on select On or set a value between those shown (10s, 20s, 30s) to turn off the display
once the chosen time has elapsed, after exiting the menu.
- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better
view of the display when the unit is hanging upside down. Select Yes to activate the function, No to
deactivate it.
- Key lock - With this function, you can lock the keys on the control panel to prevent, for example, tam-
pering with the settings. If this function is activated, the keys are locked automatically. To disable or
temporarily disable or disable the key lock function, press the keys in the following order to regain
access to the menu commands: UP, DOWN, UP, DOWN, ENTER. Select Yes to activate the function or
No to deactivate it.
• Press the ENTER button to confirm the selection.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.8 ADVANCED
You can change the parameters for the device by following these steps:
• Press the button MENU to enter the menu mode.
• Press UP/DOWN button to select the Advanced. Press the ENTER button to confirm.
• Press UP/DOWN button to select the desired option and press the ENTER button to confirm:
- Full On Mode - Select the Full on Mode function to set the HB mode (High Brightness Mode, with the
13
ECLFR2KTW
maxinum value of the colors) or Studio mode with a automatic white balance.
- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specific dimming curve.
Particularly when set:
• Off: The increase in light intensity is linear.
• Dimmer 1: dimmer curve with low fade.
• Dimmer 2: dimmer curve with medium fade.
• Dimmer 3: dimmer curve with high fade.
- White Balance - To balance the white on each color. Select the color (Red, Orange, Green, Royal Blue, Blue
and Lime) and the value (125-255) using the UP / DOWN button and press the ENTER button to confirm.
- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the UP /
DOWN button and press ENTER to confirm the selection.
- Fan Mode - Fan Speed. Select the fan speed (Auto, On, Off, Silent) using the UP / DOWN button.
- Factory Reload - To reset the unit. Select Yes or No and select the UP / DOWN button to confirm.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.9 INFORMATION
To view all the information on the device, proceed as follows:
• Press the button MENU to enter the menu mode.
• Press UP/DOWN button to select Information, then press the ENTER button to access the next menu.
• Press UP/DOWN button to scroll through the menu, then select one of the following informationa and
press the ENTER button to display it.
- Fixture Time - To view the operating time of the projector.
- Software Version - To view the firmware version will show on the display.
- UID - To view the identification ID for the RDM control.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
3.10 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the first unit in line; other units will work as slave.
• Press the button MENU so many times until the display shows Stand Alone, then press the ENTER button
to select Master/Slave.
• Press UP/DOWN button to select the desired mode and then press ENTER to confirm.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last fixture (see page 13).
• Set the slaves to the same DMX modes.
NOTE: the unit, set in Static or Effect mode, always appears to be Master.
3.11 EFFECTS MODE
This fixture has a built-in automatic program. To access this, please see the below instructions:
• To enter the Effects mode, press the ENTER button to access the menu.
• Press UP/DOWN button to select Stand Alone, then select Effect. Press ENTER to confirm
• Press UP/DOWN button to select the desired program Effect 1, Effect 2, Effect 3, Effect 4, then press ENTER
to confirm.
• Set the value (1 - 100), then press the ENTER button to confirm.
NOTE: after selecting the described mode, the unit will be Master.
ECLFR2KTW
14
3.12 FIXED COLORS
This fixture has the ability to accept custom static color settings. Access these chases via the control panel
on the back of the fixture.
• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button.
• Using UP/DOWN button select Static, then press ENTER.
• Select Fixed Color through the UP/DOWN buttons, then press the ENTER button.
• Set the colors R , O, G, W, RB, B, L, R.O.G.RB.B.L through the UP/DOWN buttons, then press the ENTER button.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
NOTE: after selecting the described mode, the unit will be Master.
3.13 MANUAL MODE
This mode allows to combine the colors (Red, Orange, Green, Royal Blue, Blue and Lime).
• Press the MENU button so many times until the display shows Stand Alone, then press the ENTER button..
• Select Manual Color through the UP/DOWN buttons, then press the ENTER button.
• Select the color Red, Orange, Green, Royal Blue, Blue and Lime through the UP/DOWN buttons, then press the
ENTER button.
• Using UP/DOWN buttons, select the desired color value 000 - 255.
• Press the ENTER button to continue to the next color Red, Orange, Green, Royal Blue, Blue and Lime.
• Continue until the desired mix is obtained.
• Press the MENU button to go back or to meet the waiting time to exit the setup menu.
NOTE: after selecting the described mode, the unit will be Master.
NOTE: If the projector is in Blackout mode before to receive DMX signal, and if the DMX signal is lost, the
projector will remain on according to the last received DMX value. If the projector was in STATIC or AUTO
mode before to receive DMX signal, if the DMX signal is lost, the projector will return to the previously set
STATIC or AUTO
1 CHANNEL
MODE
FUNCTION DMX
Value
1 Ch
1
DIMMER
0~100% 000 - 255
2 CHANNELS
MODE
FUNCTION DMX
Value
2 Ch
1
DIMMER
0~100% 000 - 255
2
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
5 CHANNELS 1
MODE
FUNCTION DMX
Value
5 Ch1
1
DIMMER
0~100% 000 - 255
2
CTO
2800K - 3000K
3000K - 3200K
3200K - 3400K
3400K - 3600K
3600K - 3800K
3800K - 4000K
4000K - 4200K
4200K - 4400K
4400K - 4600K
4600K - 4800K
4800K - 5000K
5000K - 5200K
5200K - 5400K
5400K - 5600K
5600K - 5800K
5800K - 6000K
6000K - 6200K
6200K - 6400K
6400K - 6600K
6600K - 6800K
6800K - 7000K
7000K - 7200K
7200K - 7400K
7400K - 7600K
7600K - 7800K
7800K - 8000K
8000K - 8200K
8200K - 8400K
8400K - 8600K
8600K - 8800K
8800K - 9000K
9000K - 9200K
9200K - 9400K
9400K - 9600K
9600K - 9800K
9800K - 10000K
000 - 007
007 - 014
014 - 021
021 - 028
028 - 035
035 - 042
042 - 049
049 - 056
056 - 063
063 - 070
070 - 077
077 - 084
084 - 091
091 - 098
098 - 105
105 - 112
112 - 119
119 - 126
126 - 133
133 - 140
140 - 147
147 - 154
154 - 161
161 - 168
168 - 175
175 - 182
182 - 189
189 - 196
196 - 203
203 - 210
210 - 217
217 - 224
224 - 231
231 - 238
238 - 245
245 - 255
3
HUE
0
-25°~25°
000 - 000
001 - 255
4
COLOR MACRO
No Function
Amber Shift on
Color Macro
000 - 002
003 - 005
006 - 255
5
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
15
ECLFR2KTW
3.14 CHANNELS DMX
5 CHANNELS 2
MODE
FUNCTION DMX
Value
5 Ch2
1
DIMMER
0~100% 000 - 255
2
DIMMER FINE
0~100% 000 - 255
3
CTO
2800K - 3000K
3000K - 3200K
3200K - 3400K
3400K - 3600K
3600K - 3800K
3800K - 4000K
4000K - 4200K
4200K - 4400K
4400K - 4600K
4600K - 4800K
4800K - 5000K
5000K - 5200K
5200K - 5400K
5400K - 5600K
5600K - 5800K
5800K - 6000K
6000K - 6200K
6200K - 6400K
6400K - 6600K
6600K - 6800K
6800K - 7000K
7000K - 7200K
7200K - 7400K
7400K - 7600K
7600K - 7800K
7800K - 8000K
8000K - 8200K
8200K - 8400K
8400K - 8600K
8600K - 8800K
8800K - 9000K
9000K - 9200K
9200K - 9400K
9400K - 9600K
9600K - 9800K
9800K - 10000K
000 - 007
007 - 014
014 - 021
021 - 028
028 - 035
035 - 042
042 - 049
049 - 056
056 - 063
063 - 070
070 - 077
077 - 084
084 - 091
091 - 098
098 - 105
105 - 112
112 - 119
119 - 126
126 - 133
133 - 140
140 - 147
147 - 154
154 - 161
161 - 168
168 - 175
175 - 182
182 - 189
189 - 196
196 - 203
203 - 210
210 - 217
217 - 224
224 - 231
231 - 238
238 - 245
245 - 255
4
COLOR MACRO
No Function
Amber Shift on
Color Macro
000 - 002
003 - 005
006 - 255
5
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
7 CHANNELS 1
MODE
FUNCTION DMX
Value
7 Ch1
1
RED
0~100% 000 - 255
2
ORANGE
0~100% 000 - 255
3
GREEN
0~100% 000 - 255
4
ROYAL BLUE
0~100% 000 - 255
5
BLUE
0~100%
000 - 255
6
LIME
0~100% 000 - 255
7
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
7 CHANNELS 2
MODE
FUNCTION DMX
Value
7 Ch2
1
DIMMER
0~100% 000 - 255
2
RED
0~100% 000 - 255
3
ORANGE
0~100% 000 - 255
4
GREEN
0~100% 000 - 255
5
ROYAL BLUE
0~100% 000 - 255
6
BLUE
0~100%
000 - 255
7
LIME
0~100% 000 - 255
ECLFR2KTW
16
8 CHANNELS
MODE
FUNCTION DMX
Value
8 Ch
1
COLOR PICKER
No Funciton
3200K
71
97
100
101
102
103
104
105
106
107
110
111
113
115
116
117
118
119
120
121
122
124
126
128
130
132
134
135
136
137
138
139
141
144
147
151
152
156
157
158
161
164
165
166
170
174
179
180
181
182
195
197
000 - 000
001 - 003
004 - 007
008 - 011
012 - 015
016 - 019
020 - 023
024 - 027
028 - 031
032 - 035
036 - 039
040 - 043
044 - 047
048 - 051
052 - 055
056 - 059
060 - 063
064 - 067
068 - 071
072 - 075
076 - 079
080 - 083
084-087
088 - 091
092 - 095
096-099
100 - 103
104 - 107
108 - 111
112 - 115
116 - 119
120 - 123
124 - 127
128 - 131
132 - 135
136 - 139
140 - 143
144 - 147
148 - 151
152 - 155
156 - 159
160 - 163
164 - 167
168 - 171
172 - 175
176 - 179
180 - 183
184 - 187
188 - 191
192 - 195
196 - 199
200 - 203
204 - 207
208 - 211
8 CHANNELS
MODE
FUNCTION DMX
Value
8 Ch
198
200
201
202
203
204
205
206
702
730
777
212 - 215
216 - 219
220 - 223
224 - 227
228 - 231
232 - 235
236 - 239
240 - 243
244 - 247
248 - 251
252 - 255
2
DIMMER
0~100% 000 - 255
3
RED
0~100% 000 - 255
4
ORANGE
0~100% 000 - 255
5
GREEN
0~100% 000 - 255
6
ROYAL BLUE
0~100% 000 - 255
7
BLUE
0~100%
000 - 255
8
LIME
0~100% 000 - 255
17
ECLFR2KTW
12 CHANNELS
MODE
FUNCTION DMX
Value
12 Ch
1
DIMMER
0~100% 000 - 255
2
STROBE
No Function
Strobe slow to fast
000 - 010
011 - 255
3 RED 000 - 255
4 ORANGE 000 - 255
5 GREEN 000 - 255
6 ROYAL BLUE 000 - 255
7 BLUE 000 - 255
8 LIME 000 - 255
9
CTO
2800K - 3000K
3000K - 3200K
3200K - 3400K
3400K - 3600K
3600K - 3800K
3800K - 4000K
4000K - 4200K
4200K - 4400K
4400K - 4600K
4600K - 4800K
4800K - 5000K
5000K - 5200K
5200K - 5400K
5400K - 5600K
5600K - 5800K
5800K - 6000K
6000K - 6200K
6200K - 6400K
6400K - 6600K
6600K - 6800K
6800K - 7000K
7000K - 7200K
7200K - 7400K
7400K - 7600K
7600K - 7800K
7800K - 8000K
8000K - 8200K
8200K - 8400K
8400K - 8600K
8600K - 8800K
8800K - 9000K
9000K - 9200K
9200K - 9400K
9400K - 9600K
9600K - 9800K
9800K - 10000K
No Funciton
000 - 007
007 - 014
014 - 021
021 - 028
028 - 035
035 - 042
042 - 049
049 - 056
056 - 063
063 - 070
070 - 077
077 - 084
084 - 091
091 - 098
098 - 105
105 - 112
112 - 119
119 - 126
126 - 133
133 - 140
140 - 147
147 - 154
154 - 161
161 - 168
168 - 175
175 - 182
182 - 189
189 - 196
196 - 203
203 - 210
210 - 217
217 - 224
224 - 231
231 - 238
238 - 245
245 - 252
253 - 255
9 CHANNELS
MODE
FUNCTION DMX
Value
9 Ch
1
DIMMER
0~100% 000 - 255
2
RED
0~100% 000 - 255
3
ORANGE
0~100% 000 - 255
4
GREEN
0~100% 000 - 255
5
ROYAL BLUE
0~100% 000 - 255
6
BLUE
0~100%
000 - 255
7
LIME
0~100% 000 - 255
8
STROBE
No Function
Strobe slow to fast
000 - 010
011 - 255
9
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
ECLFR2KTW
18
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
ProLights ECLFR2KTW Manuale utente
- Categoria
- Stroboscopi
- Tipo
- Manuale utente
in altre lingue
- English: ProLights ECLFR2KTW User manual
Documenti correlati
-
ProLights LED Fresnel FC and Tunable White Manuale utente
-
-
-
-
-
-
-
ProLights LED Fresnel Manuale utente
-
-