Crowcon Gas-Pro TK Istruzioni per l'uso

H

2

S

CO

CH

4

Gas-Pro

User & Operator Manual

Gas-Pro

Multi-gas monitor

M07995/Eng

Issue 11 Dec 2016

Click here for

contents

list

Click here

for navigation

instructions

NAVIGATION INSTRUCTIONS

The symbols in the left-hand margin of each page of the manual will enable you to carry out the

following functions:

Click on this button to display the Contents page.

Click on this button to display the previous page.

Click on this button to display the next page.

Click on this button to display the previous view (use it to return from a reference jump).

Click on this button to display next view (use it to return to a reference jump).

Click this button to print some or all of the document (specic pages can be chosen).

Exit

Click this button to exit the User and Operator Manual.

!

Press the Esc key to display normal Acrobat

©

Controls.

Contents

3

CONTENTS

PROLOGUE .............................................7

Gas-Pro Overview ...............................................7

Safety Information ........................................8

Unpacking .............................................11

1. Set-up ..............................................12

1.1 Prior to use .................................................12

1.2 Gas-Pro orientation ..........................................12

1.3 Charging ...................................................13

1.4 Fitting a ow plate ...........................................14

1.5 Quick view .................................................15

2. Operation ...........................................16

2.1 General ....................................................16

2.2 Turn on ....................................................16

2.3 Pump test ..................................................20

2.4 Detecting gas ...............................................21

2.4.1 Diffusion monitoring .....................................21

2.4.2 Pumped mode ..........................................22

2.4.3 Manual sampling ........................................23

2.4.3.1 Using the Hand Aspirator .............................23

2.5 Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

2.5.1 Low battery alarm .......................................24

2.5.2 Instantaneous alarm .....................................24

2.5.3 Time weighted average alarm (TWA) ........................24

2.5.4 Accepting and clearing alarms ............................25

Exit

4

2.5.5 Sensor types ...........................................25

2.5.5.1 Oxygen sensors ....................................25

2.5.5.2 Electro-chemical sensors .............................25

2.5.5.3 Infra red sensors ...................................25

2.5.5.4 Pellistor sensors ....................................26

2.5.5.5 Pellistor saver mode

.............................26

2.5.5.6 PID .............................................27

2.6 Gas-Pro functions ...........................................28

2.6.1 Accessing the user menus ................................28

2.6.2 Home screen

........................................28

2.6.3 Manual zero

.........................................28

2.6.4 Time weighted average

................................28

2.6.5 Pre-entry check (PEC)

.................................29

2.6.5.1 Starting a Pre-entry check ............................29

2.6.5.2 Carrying out a Pre-entry check ........................30

2.6.6 Peak review

.........................................31

2.6.7 Settings

............................................31

2.6.7.1 User setting

....................................31

2.6.7.2 Pump setting

...................................31

2.6.7.3 Sounder volume

.................................31

2.7 Shut down .................................................32

2.8 Additional Features ..........................................32

2.8.1 +ve Safety™ ............................................32

2.8.1.1 +ve Safety™ indicator meanings .......................32

2.8.2 Data and event logging ...................................33

2.8.3 Bump/Pump functionality .................................33

Exit

5

2.9 Tank Check Mode ...........................................34

2.9.1 Dual-Range Operation ...................................35

2.9.2 Differences with Home Screen .............................35

2.9.2.1 Instantaneous Alarms ...............................35

2.9.2.2 TWA .............................................35

2.9.2.3 Pre-Entry Check (PEC) ..............................35

2.9.2.4 Condence Tone ...................................36

2.9.2.5 Display Backlight ...................................36

3. Gas testing and calibration .............................37

3.1 Introduction ................................................37

3.2 Bump Test Functionality ......................................38

3.2.1 Speedy bump ...........................................39

3.2.1.1 Procedure ........................................39

3.2.2 Smart bump ............................................39

3.2.2.1 Procedure ........................................39

3.2.3 Calibration after bump fail ................................40

3.2.3.1 Procedure ........................................40

3.3 New sensor calibration/service ................................40

3.4 Gas test screen ow .........................................41

4. Icon overview ........................................42

5. Service and maintenance ..............................43

6. PC interface and Portables Pro .......................... 44

6.1 General ....................................................44

6.2 PC interface cable ...........................................44

7. Accessories .........................................45

Exit

6

8. Specication .........................................47

9. Troubleshooting ......................................48

9.1 Pump test failure ............................................48

9.2 Fault screens ...............................................48

9.2.1 Fault Descriptions .......................................49

9.2.2 Fault codes ............................................51

10. Appendices ..........................................52

10.1 Sensors ..................................................52

10.1.1 Toxic .................................................52

10.1.2 Flammable Pellistor Sensors .............................53

10.1.3 Flammable IR Sensors ..................................53

10.1.4 Oxygen ...............................................53

10.1.5 IR ....................................................53

10.1.6 PID ..................................................53

10.2 Sensor Limitations .........................................54

10.3 Charging and run times .....................................55

10.4 Contacts ..................................................56

Warranty ...............................................57

Exit

7

PROLOGUE

Gas-Pro Overview

Thank you for purchasing the new Gas-Pro. At Crowcon we recognise the need for reliable and

robust personal monitors which are sized to be worn and simple to use.

Gas-Pro is a portable monitor capable of detecting up to 5 gases in a compact and wearable design

featuring an optional internal pump. Focused on users and eet managers alike, Gas-Pro offers

application focused solutions giving greater operating time and reduced set up time.

Gas-Pro is classied for use in hazardous areas and gives loud and bright audible and visual alarm

indications as well as a vibrate alert. The top mount display is backlit for ease of use, and the simple

single button solution makes using and training quick and easy.

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

8

Safety Information

• Gas-Pro is a hazardous area certied gas detector and as such must be operated and

maintained in strict accordance with the instructions, warnings and label information included in

this manual. Gas-Pro must be operated within the limitations stated.

• Read and understand all instructions in the operation section of this manual prior to use.

• Before use ensure that the equipment is in good condition, the enclosure is intact has not been

damaged in any way.

• If there is any damage to the equipment do not use, contact your local ofce or agent for repair/

replacement.

• Do not disassemble or substitute components as this may impair intrinsic safety and invalidate

safety certication.

• Only genuine replacement parts must be used; substitute components may invalidate

certication and warranty of the Gas-Pro and accessories, reference “Service and

Maintenance” section for details.

• No live maintenance is permissible.

• Observe all warnings and instructions marked on the unit and within this manual.

• Observe site health and safety procedures for gases being monitored and evacuation procedures.

• Understand the screen display and alarm warnings prior to use.

• If this product is not working properly, read the troubleshooting guide and/or contact your local

ofce or agent, for details reference the ‘Contacts’ section of the manual (see page 52).

• Ensure maintenance, service and calibration is carried out in accordance with the procedures in

the manual and only by trained personnel.

• The Gas-Pro re-chargeable battery must only be charged in non-hazardous (safe) areas.

• Only connect to Gas-Pro in a safe area for charging or communications.

• Gas-Pro must not be charged or have communication to the device, at ambient temperatures

greater than +40°C.

• Charging cable assemblies, whilst nominally providing a voltage of 6.5V, must not exceed a

voltage of 9.1V as this may impair intrinsic safety and invalidate safety certication (Um=9.1V).

• Communication cable assemblies, whilst nominally operating at a voltage of 3.0V TTL, must not

exceed a voltage of 9.1V as this may impair intrinsic safety and invalidate safety certication

(Um=9.1V).

• The devices are intended for use in normal atmospheric conditions of temperature –20 °C to

+55 °C; pressure 80 kPa (0,8 bar) to 110 kPa (1,1 bar); and air with normal oxygen content,

typically 21 % v/v (volume/volume).

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

9

• Gas-Pro may be used in Zones 1 and 2, for Group llA, llB and llC gases and vapours and for

Temperature Classes T1, T2, T3 and T4. (see Certication labels below).

• Certication labels

The certication marking is as follows:

• Gas-Pro is certied for use in ambient temperatures in the range -20°C to +55°C (-4 to 131°F).

• Applicable Standards

Refer to equipment marking for conrmation of applicable certication before use.

IECEx

IEC 60079-0: 2013, 6th Edition

Explosive atmospheres – Part 0: Equipment - General requirements

IEC 60079-1:2007, 6th Edition

Explosive atmospheres – Part 1: Equipment protection by ameproof enclosures “d”

IEC 60079-11: 2012, 6th Edition

Explosive atmospheres - Part 11: Equipment protection by intrinsic safety “i”

Ex d ia IIC T4 Gb Tamb -20°C to +55°C

IECEx ULD 11.0004X

UL certification label

CH4

1180

Um = 9.1V

WA RNING -

DO NOT CHA RGE THE BATTERY OR

CONNECT TO THE EQUIPMENT IN A

HAZARDOUS LOCATION.

REA D A ND UNDERSTA ND THE MA NUA L

B EFORE USE.

172 BROOK DRIVE

MILTON PARK, ABINGDON

OX14 4SD

UNITED KINGDOM

66Y6

T4 Tamb: -20°C to +55°C

FOR USE IN HA ZA RDOUS

LOCATIONS, CLA SS I, DIVISION 1,

GROUPS A , B, C & D.

ONLY AS TO INTRINSIC SA FETY

ATEX/ certification labelIECEx MED certification label

1180

CH4

II 2 G

IECEx ULD 11.0004X

DEMKO 11ATEX1031772X

WARNING

DO NOT CHARGE THE BATTERY OR

CONNECT TO THE EQUIPMENT IN A

HAZARDOUS LOCATION.

READ AND UNDERSTAND THE MANUAL

BEFORE USE.

172 BROOK DRIVE

MILTON PARK, ABINGDON

OX14 4SD

UNITED KINGDOM

Um = 9.1V

Ex d ia IIC T4 Gb -20°C Ta +55°C

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

10

ATEX

EN 60079-0: 2012 + A11: 2013

Explosive atmospheres – Part 0: Equipment - General requirements

EN 60079-1:2007

Explosive atmospheres – Part 1: Equipment protection by ameproof enclosures “d”

EN 60079-11: 2012

Explosive atmospheres - Part 11: Equipment protection by intrinsic safety “i”

II 2 G Ex d ia IIC T4 Gb Tamb -20°C to +55°C

DEMKO 11 ATEX 1031772X

UL

Gas detector use in hazardous locations Class 1 Division 1, Groups A, B, C and D only as to

intrinsic safety.

UL 913 Applicable Edition of the UL standard

UL60079-0 Applicable Edition of the UL standard

UL60079-11 Applicable Edition of the UL standard

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

11

Unpacking

Remove the Gas-Pro from the packaging. The standard accessories are under the supporting trays.

The following items will be included as standard:

Box contents

• Gas-Pro

• Quick Start Guide

• CD Manual

• Calibration report

The following items are optional:

Optional items

• Charger cradle

• Charger lead (see Power & Communication Cables Technical Data)

• Flow plate (standard for pumped units)

i

If you have ordered a charger and/or cradle this will also be included in the box.

Further accessories are available but will not be contained in the box (see Section 7).

i

Gas-Pro in the off state can be left on charge indenitely

i

Should the unit be deep discharged, the charging indication will not be shown until the

unit has been charging for 1 hour and the operator button has been pressed.

i

When on and charging a warning will advise the user to turn the Gas-Pro off after 12

hours or remove from charge.

i

Store the battery in a full state and recharge at least once every 3 months.

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

12

1. Set-up

1.1 Prior to use

Before use, the Gas-Pro should always be checked for any signs of physical damage.

Gas-Pro uses a Lithium Ion (Li-ion) battery pack and should arrive with sufcient charge to be used

straight out the box. However, if this is the rst time of use, you may need to charge the battery to

attain the full operating time (see Charging on page 13).

For battery run times, see the table on page 55.

i

The actual operating time will depend on the types of sensor installed.

1.2 Gas-Pro orientation

Figure 1: Gas-Pro

À D-ring Ã Sounder Æ Sensor apertures É Charging cable

Á Alarm bars Ä Operator button Ç Dual colour LCD display Certication label

Â +ve Safety™ indicator Å Pump inlet/outlet* È Alligator clip

* Blanked for non-pumped unit.

À

Ç

Ã

É

È

Ä

Â

Å

Æ

Á

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

13

1.3 Charging

Charging should only take place in non-hazardous (safe) areas. To charge, simply plug the cable À into

the charging socket Á on the Gas-Pro and turn on the mains supply (see Figure 2 below). If a charging

cradle or vehicle cradle is being used, ensure the Gas-Pro ts rmly on to the power connector.

i

The charger must be able to supply 6.5V@ 450mA with an output voltage that does not

exceed 9.1V (Um).

Figure 2: Charger connection

When off, to show the Gas-Pro is charging, both LEDs within the alarm bars will ash red and will change

to green once fully charged. This state will continue until the trickle charge is complete. Charging will then

terminate showing no indication. The screen will also show the battery icon lling in the middle of the

screen when the Gas-Pro is off, and in the bottom left-hand corner when it is on. The battery icon contains

a maximum of six segments to indicate the battery’s state of charge. For example, with three segments

shown and a fourth ashing, the battery is 50% charged

À, and when all six are shown, the battery is fully

charged Á (see Figure 3 below).

Figure 3: Charging indications

À

Á

À Á

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

14

1.4 Fitting a ow plate

A ow plate can be used for a number of applications including pumped operation (remote sampling),

manual gas test/calibration or for manual sampling. If the pumped ow plate is attached before turning

the Gas-Pro on and the Gas-Pro includes a pump, a pump test will commence as part of the start up

process (see Pump test on page 20).

There are 3 types of ow plate: one for a Gas-Pro with internal pump, one for a Gas-Pro with no

pump and a non-magnetic version for PC calibration or for manual sampling. Although there is no

difference to the attachment procedure, they are not interchangeable (see Figure 4). The pumped

ow plate has the

symbol in the top left corner to aid recognition.

Figure 4: Pumped and non pumped ow plates

À Pumped ow plate

Á Non pumped ow plate

Â PC Cal/Test Flow Plate

Check the ow plate’s gasket is free from dirt and has not been damaged prior to tting. To t a ow

plate, locate it over the Gas-Pro sensors as shown in Figure 5 and tighten the securing screw

À.

Figure 5: Fitting a ow plate

The ow plate includes a quick connect tting for attaching sample tubes and probes.

À

Á Â

À

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

15

1.5 Quick view

Even when the detector is off, users can display details about the conguration of the Gas-Pro by

momentarily pressing the operator button for one audible blip. The LED to the left of the display will

ash red once and the Quick view screen shown in Figure 6 below will be displayed for 10 seconds.

Figure 6: Quick view display

À Gas type and unit detected

Á Battery status

Â Quickview icon

Ã ID or serial number

i

The +ve Safety™ LED status is also shown (see Figure 1).

Ã

Á

À

Â

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

16

2. Operation

2.1 General

!

Before turning the Gas-Pro on, ensure it is in ‘clean air’ (i.e. outside, in normal air, away

from any plant process or suspected gas location). This will allow the Gas-Pro to be

zeroed using clean air as the base point. If the Gas-Pro is zeroed in contaminated air a

false gas reading can result, or the zero could fail.

2.2 Turn on

In ‘clean air’, turn on the Gas-Pro by holding down the operator button for 3 audible blips. The Gas-

Pro will warm up, going through a series of automatic processes as follows:

Firstly a test screen pattern will be generated. Watch this to ensure there are no missing pixels on

your display screen.

Whilst the Gas-Pro is warming up, two screens will be displayed.

Figure 7: Initial screens at turn on

After a successful test cycle the LCD screen will remain green, the sounder and LEDs will indicate

the Gas-Pro is healthy.

i

A Gas-Pro tted with a pump is congured as standard to start the pump automatically

when switched on, provided that a ow plate is tted. Such a Gas-Pro tests the pump

automatically at this point (for more details on this, see Pump test on page 20).

i

If the battery level is low, an alarm will sound, and the battery icon on the screen will be partial.

i

If a second ‘splash’ screen has been congured via Portables Pro it will be shown next in

the turn on sequence.

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

17

If the Gas-Pro is congured for regular Gas Testing (Bump Test), the date of the last Gas Test will

also be shown (for more information on Gas Testing, see Gas testing and calibration on page 37).

Figure 8: Gas test due screen

The next screen indicates when the Gas-Pro was last calibrated. It also indicates when the next calibration

is due with a warning symbol

next to the number of days left, if this is fewer than 30 days. If the

calibration due date has expired, the number of days gure is not displayed and the warning symbol

ashes.

Figure 9: Calibration due screen

If the calibration due lockout feature has been enabled the lockout icon

will be displayed and the

Gas-Pro will not proceed past this point.

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

18

The next screen (Figure 10) will display the current detector settings (for more information on these

settings, see Gas-Pro functions on page 28).

Figure 10: Current settings screen

The Autozero Conrm screen will be displayed next.

Figure 11: Autozero conrm screen

An Autozero should not be performed unless the Gas-Pro is in clean air. Press the operator button to

enter the Autozero mode, otherwise the countdown will progress and will not perform a zero.

If the operator button is not pressed the countdown will complete and this function will be skipped.

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

19

When the autozero has nished or been skipped, the next screen is the home screen (Figure 12)

and displays the gas levels.

The next screen on the Tank-Pro edition of Gas-Pro is the Tank Check

screen. See the Tank

Check Mode section (see Section 2.9 on page 34) for more information.

i

Figure 12 shown below is for 5 gases in clean air.

Figure 12: Home screen

À Gas type

Á Unit

Â Level

Ã Home Screen icon

Ä Battery level

Å Pump present

(rotating when on)

In ‘clean air’, CO

2

and Oxygen levels are typically 0.04% and 20.9% respectively. In zero mode,

these gases will actually run an ‘offset’ zero.

The Gas-Pro is now ready for use.

!

From the 1st November 2010, EN60079-29 part 1 has been harmonised under the ATEX

directive 94/9/EC. Therefore to comply with the ATEX directive, portable apparatus sensing

ammable gases should have a functional check with ammable gas before each day of

use (see Gas testing and calibration on page 37). Other testing regimes may be employed

depending on local circumstances.

À Á

Â

Ã

Ä

Å

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

20

2.3 Pump test

In the default conguration, a pumped Gas-Pro with a ow plate attached (see Fitting a ow plate on

page 12) will run a pump test during the start up process. A pump test will also be run whenever a

ow plate is attached during normal operation.

i

If the Gas-Pro is congured for Bump functionality, the Bump/Pump prompt will be

displayed if a ow plate is attached and a gas bump test is due or the Gas-Pro is placed in

a Q-Test module during normal use (see Bump/Pump functionality on page 33).

i

Prior to tting, the ow plate’s gasket should be checked for any damage.

The pump test ensures accurate sealing as well as monitoring pump performance.

The user will need to cover the pump inlet

À (see Figure 13 below) when prompted to do so by the

symbol on the screen.

Figure 13: Pump inlet

When the test has nished, the pump will either pass

or fail .

If the pump test takes place during start-up and the Gas-Pro passes, the pump will remain on and

the start-up process will continue as normal. If the test is passed during normal use, the Gas-Pro will

remain in the pumped mode until the ow plate is removed.

On failing the pump test the fail screen will persist with an audible alert until the button is pressed

and the test repeats OR the ow plate is removed and the Gas-Pro returns to unpumped operation.

For further detail on failing a pump test see Pump test failure on page 48.

À

Contents

Exit

Prologue

Operation

Gas testing

Maintenance

PC software

Accessories

Specication

Troubleshooting

Appendices

Warranty

Set-up

La pagina sta caricando ...

Crowcon Gas-Pro TK Istruzioni per l'uso

Questo manuale è adatto anche per

Crowcon Gas-Pro TK Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti