Crowcon IRmax Installation, Operating And Maintenance Instruction

IRmax

Installation, operating and maintenance instructions

Instructions d’installation, d’utilisation et de maintenance

Installations-, Bedienungs- und Wartungsanleitung

Instrucciones de instalación, operación y mantenimiento

Istruzioni d’installazione, uso e manutenzione

Installatie-, bedienings- en onderhoudsinstructies

Instrukcje montażu, obsługi i konserwacji

Instruções de instalação, funcionamento e manutenção

M07028

Issue 6 Oct 2017

Infrared hydrocarbon gas detector

Contents

Concept and safety ...................................................................................... 1

IRmax concept ..................................................................................... 1

Safety information................................................................................. 2

Product overview................................................................................... 3

1. Introduction ............................................................................................. 4

1.1 General ........................................................................................... 4

1.2 Product description ......................................................................... 4

2. Installation ................................................................................................ 6

WARNING ............................................................................................. 6

2.1 Location .......................................................................................... 6

2.2 Mounting ........................................................................................ 7

2.3 Cabling directly to IRmax .............................................................. 7

2.3.1 Terminal designation .............................................................. 8

2.3.2 Installing IRmax using a mounting bracket ............................ 8

2.4 Installing using a spigot gland and auxiliary junction box ................ 9

2.4.1 To fit IRmax to an auxiliary junction box: ............................. 10

2.5 Cabling requirement ..................................................................... 10

2.6 Connections and settings .............................................................. 11

3. Operation ............................................................................................... 12

3.1 Commissioning procedure ............................................................. 12

3.2 Routine maintenance .................................................................... 13

3.3 Changing gas types ...................................................................... 13

3.4 Relative responses of gas types ..................................................... 14

4. Specification ........................................................................................... 15

5. Accessories and spare parts .................................................................... 16

6. Fault finding .......................................................................................... 17

6.1 Errors signalled by LED .................................................................. 17

6.2 Analogue Output .......................................................................... 17

7. RS485 Modbus configuration ................................................................. 18

7.1 General ......................................................................................... 18

7.2 Wiring topology ............................................................................ 19

7.2.1 Star connection .................................................................... 19

7.2.2 Linear bus connection .......................................................... 19

7.3 Cabling requirements .................................................................... 20

7.3.1 Calculating the minimum level of power required ............... 20

7.3.2 Sample calculation ............................................................... 20

8. Functional Safety Manual ....................................................................... 21

8.1 Introduction .................................................................................. 21

8.2 IRmax and IRmax Modbus Safety Function .................................... 21

8.3 Functional Safety Data .................................................................. 21

8.4 Hardware Configuration ............................................................... 22

8.5 Software Configuration ................................................................. 22

8.6 Systematic Failures ........................................................................ 22

8.7 Diagnostic Interval ......................................................................... 22

8.8 Constraints ................................................................................... 22

8.9 Environmental ............................................................................... 23

8.10 Hardware fault tolerance............................................................. 23

8.11 Systematic Capability .................................................................. 23

8.12 Classification ............................................................................... 23

Warranty .................................................................................................... 24

1

Detecting Gas Saving Lives

English

Concept and safety

IRmax concept

IRmax is an ultra-compact infrared (IR) gas detector, which delivers rapid, fail-safe detection

of hydrocarbon gases and vapours.

Featuring dual-wavelength IR sensor technology in a rugged 316 stainless steel package,

IRmax is designed to operate in the harshest conditions. Unlike conventional IR gas detectors,

IRmax does not incorporate heaters to prevent condensation on windows and mirrors. The

Stay clIR coating on optical components prevents condensation forming while the detector is

operating.

IRmax is compatible with any 4-20mA control system, and can also be installed in an RS485

Modbus addressable network (see Section 7).

IRmax requires only 1 Watt of power, typically 75-90% lower than conventional IR gas detectors.

IRmax features a compact diffusion gas chamber, which in combination with an effective

weatherproof cap provides excellent speed of response. The weatherproof cap has been

designed using flow modelling software to enable remote gassing and calibration of the

IRmax without requiring a special calibration cap.

The IR Display makes it possible to monitor readings from the IRmax both locally and

remotely. An IR Display can be fitted directly to IRmax. Alternatively, IRmax may be

supplied with an Intrinsically Safe (IS) Barrier module attached. An IR Display can then

be connected to the IS Barrier Module via temporary or permanent cabling. The available

options are illustrated on Diagram 3, page 5.

For further information about other accessories for the IRmax see Diagram 3 on page 5 and

Section 5, page 16.

Concept and safety

2

Detecting

Gas Saving Lives

English

Safety information

• IRmax gas detectors must be installed, operated and maintained in strict accordance

with these instructions, warnings, label information, and within the limitations stated.

• The rear nut on IRmax must be kept tightly closed during operation. Do not attempt

to remove the rear nut until power to the detector is isolated - otherwise ignition

of a flammable atmosphere can occur. Before removing the nut for maintenance,

calibration or servicing, check that the surrounding atmosphere is free of flammable

gases or vapours. Do not open until several minutes after the power has been removed.

• Maintenance and calibration operations must only be performed by qualified service personnel.

• Only genuine Crowcon replacement parts must be used; substitute components may

invalidate the certification and warranty of the IRmax.

• IRmax must be protected from extreme vibration, and direct sunlight in hot

environments as this may cause the temperature of the IRmax to rise above its specified

limits and cause premature failure.

• IRmax will not detect hydrogen, ammonia or carbon dioxide.

• The equipment must be earthed using the cable gland and steel armoured cable.

• Certification for Zone 21/22 dust environments: IRmax basic (without IR Display or

IS Barrier module) may be used in environments that may contain hazardous dusts

(Zones 21 or 22).

• IRmax with an IS Barrier module may be used in Zones 21 or 22 provided the ambient

temperature remains below 40°C and a remote IR Display or Hand-Held IR Displays are

installed/used outside the hazardous area only.

• IRmax with a Fixed IR Display cannot be installed in a Zone 21 or 22 area.

Concept and safety

3

Detecting

Gas Saving Lives

English

Product overview

IRmax is an infrared gas detector designed for detecting common hydrocarbon gases in

the range 0 to 100%LEL (Lower Explosive Limit: the minimum concentration in air at which

ignition can occur).

IRmax is a certified Flameproof (Exd) detector suitable for use in ATEX Zone 1 or Zone 2

hazardous areas. Please refer to the certification label on the side of the Detector to identify

the type of certification that relates to the product supplied.

Note: if no certification label is fitted to the IRmax, the detector is not certified for

use in hazardous areas.

Diagram 1: IRmax certification labels

0811

.TNESERP EB YAM EREHPSOMTA EVISOLPXE NEHW NEPO TON OD :GNINRAW

04- = bmaT( bG 4T CII bd xE 57+ ot C )C

W5=xamW V23=xamV

04- = bmaT

( bG 6T CII bd xE 05+ ot C )C

X9010.90 SAB xECEI X6020XETA90afeesaB

X6021XETA21 ariS 2LIS

DS4 41XO ,modgniK deitnU ,nodgnibA

DG2 II

ROTCETED SAG RI

)C°57+ aT C°04-( bD C°531T CIII bt xE

°°

°

IRmax Basic certification label

Ex db ia IIC T4 Gb (-40°C Ta +75°C)

Vmax=32V Wmax=5W

WARNING: DO NOT OPEN WHEN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

IR G A S DET E C TOR W I TH R E M OTE D I SPL A Y

Baseefa09ATEX0220X IECEx BAS 09.0104X

Abingdon, United Kingdom, OX14 4SD

1180

II 2GD

Ex tb ia IIIC T135

°C Db (-40°C Ta +40°C)

IRmax with IS Barrier certification label

+75°C)Ex db ia IIC T4 Gb (-40°C Ta

II 2G

1180

Abingdon, United Kingdom, OX14 4SD

Baseefa09ATEX0220X IECEx BAS 09.0104X

IR GA S DE TECT OR WI TH D ISPL AY

WARNING: DO NOT OPEN WHEN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.

Vmax=32V Wmax=5W

IRmax with Fixed IR Display certification label

4

Detecting

Gas Saving Lives

English

1. Introduction

1.1 General

The configuration of each IRmax is identified by a label fitted on the main body. Please

quote the product name, part number and serial number when contacting Crowcon for

advice or spares.

1.2 Product description

IRmax consists of a main body of 316 stainless steel, an antistatic weatherproof cover

over the optics and gas measurement chamber and an electronics assembly. An IR Display

Module can also be fitted. Instructions for fitting the IR Display appear in the IR Display

manual (M07061).

An optional connection spigot gland can be supplied to allow IRmax to be fitted directly

to auxiliary junction boxes with either M20 or ½” NPT cable entries.

All dimensions in millimetres

Diagram 2: IRmax dimensioned view

Note: The IRmax body is supplied with two cable entries; one is M20, one is 1/2"

NPT. The cable entry not specified when ordering an IRmax will be sealed using

a certified plug. The IRmax must be installed with both cable entries sealed: one

with a cable gland, the other with a certified IP66 rated stopping plug.

157.5

74.5

136

60.5

Optional spigot gland

57

Overall

158 Overall

74.5

136 Overall

M20 or 1/2" NPT

cable gland

External

grounding

terminal

(earth)

1. Introduction

5

Detecting

Gas Saving Lives

English

Diagram 3: IRmax exploded view (part numbers shown where applicable)

 Calibration cap M041007

 Weatherproof cap M04995

 Mirror retainer

 Mirror

 Flow adaptor S012996

 O-ring for back-nut, IS Barrier Module or Fixed IR Display Module: M040077

 Mounting bracket as complete assembly S012130

 Spigot gland M20 or 1/2"NPT versions : M20 ATEX: S012147, 1/2" NPT ATEX: S012190

 Retaining plate and bolts for rear plug, Fixed IR Display and IS Barrier module

10

IR Display fixed version

11

IR Display to IRmax connector E07987

12

IS Barrier Module

13

IR Display connecting lead

14

Remote IR Display mounting bracket M03833

15

Remote IR Display



















10

11

12

13

14

15

}

Supplied together as ‘mirror replacement kit’

C011206

6

Detecting

Gas Saving Lives

English

2. Installation

WARNING

• This detector is designed for use in Zone 1 and Zone 2 hazardous areas.

Certification is dependent upon the accessories fitted and ambient operating

temperature. Please refer to the specifications table on page 15 for

certification details. Installation must be in accordance with the recognised

standards of the appropriate authority in the country concerned.

• For further information please contact Crowcon. Prior to carrying out any

installation work ensure local regulations and site procedures are followed.

• The equipment must be earthed using the cable gland and steel armoured cable.

• Do not attempt to fit an IR Display to an IRmax not supplied for the purpose.

Detectors supplied for use with a display are certified Exd ia, and must be

operated either with a Fixed Display containing an IS barrier, or with a Remote

IR Display or IS Hand-Held Calibrator connected via a Crowcon IS Barrier module.

• Detectors supplied without a display are certified Exd IIC and cannot be retro-

fitted for use with an IR Display.

2.1 Location

The IRmax should be mounted where the gas to be detected is most likely to be present.

The following points should be noted when locating gas detectors:

• To detect gases which are lighter than air, such as methane, detectors should be

mounted at high level. To detect heavier-than-air gases, such as flammable vapours,

detectors should be mounted at low level.

• When locating detectors consider the possible damage caused by natural events

e.g. rain or flooding. For detectors mounted outdoors in very hot regions Crowcon

recommend the use of a sunshade (see Section 5, Accessories and spare parts, on

page 16).

• Consider ease of access for functional testing and servicing.

• Consider how the escaping gas may behave due to natural or forced air currents.

Mount IRmax in ventilation ducts if appropriate (see Section 5, Accessories and spare

parts, on page 16).

• Consider the process conditions. For example, butane is normally heavier than air, but

if released from a process which is at an elevated temperature and/or pressure, the

gas may rise rather than fall.

The placement of sensors should be determined following advice of experts having specialist

knowledge of gas dispersion and the plant processing equipment as well as safety and

engineering issues. The agreement reached on the locations of sensors should be recorded.

2. Installation

7

Detecting

Gas Saving Lives

English

2.2 Mounting

IRmax can be mounted in three ways:

1. Using the Crowcon mounting bracket with direct field cable connection (4-20mA

operation only).

2. Using a spigot gland to connect to an existing Exe or Exd certified junction box. Crowcon

supplies a suitable spigot gland as an optional extra (see 3 below).

3. Using the optional Crowcon auxiliary junction box and spigot gland.

Optional parts are listed in Section 5 on page 16.

IRmax should be installed at the designated location with the sensor barrel horizontal

+/- 15° (orientation shown on Diagram 2 on page 4). This ensures that dust or water

will not collect on the optical components.

2.3 Cabling directly to IRmax

This option is suitable for 4-20mA operation only. A Crowcon mounting bracket is required

to retain the detector to a wall or 2” (50 mm) pipe.

Diagram 4: Field cable connections on the IRmax

Connect field cables using a certified gland via the chosen cable entry on the IRmax body

(M20 or 1/2" NPT), as indicated in Diagram 4. Crowcon recommends cable glands are

installed pointing downwards.

Ensure that cable glands with the appropriate

Exd certification are used, and that the thread

length does not exceed the length specified in the

diagram (left).

Signal

0V (ground)

+V (24V IRmax)

15mm MAX

Status LED

2. Installation

8

Detecting

Gas Saving Lives

English

2.3.1 Terminal designation

With the IRmax oriented as shown in Diagram 2 on page 4 (M20 cable entry at the

top), the 3-core field cable should be terminated using the removable connector as follows:

+24V at the bottom, 0V in the middle, Signal at the top.

The 6-pin connector on the right of the PCB is for servicing and/or connection of an

IR Display module

+ve terminal: +ve supply from the control card.

Sig terminal: Signal/Sense from control card.

0 V terminal: -ve supply from the control card.

2.3.2 Installing IRmax using a mounting bracket

a. IRmax can be supplied with a mounting bracket (S012130) rather than a spigot

gland so that it can be directly connected to field cables (see Diagram 5).

Diagram 5: IRmax with a mounting bracket and cable gland

b. If the IRmax is to be mounted on a flat surface, mark and drill two holes using

the mounting bracket as a template. Loosely fix two parts of the bracket using

fixings suitable for the wall/surface.

c. Remove the weatherproof cap from the IRmax, and slide the body of the IRmax

through the bracket. It is recommended that the IRmax body is installed with the

cable entry facing downwards.

Mounting bracket: 70mm

between fixing centres.

Use M6 bolts

2. Installation

9

Detecting

Gas Saving Lives

English

d. Secure the two bracket fixings so that the IRmax is held firmly in place. Re-fit the

weatherproof cap.

e. Once the IRmax is securely fixed in place, remove the IRmax rear nut to enable

access to the cable terminals.

f. Prepare the field cable – Crowcon recommends 1.5 mm

2

Steel Wire Armoured

(SWA) cable. Other cable types may be used provided they are compatible

with Exd certified glands. Fit a suitably certified Exd cable gland, pass the cable

conductors through the body of the IRmax and screw in the cable gland. Secure

the gland and ensure the cable armour is grounded to the cable gland and the

IRmax body. NB. Don’t forget to re-fit the rear nut after installing the cable.

g. The retaining plate (item 9 on Diagram 3, page 5) must be securely fitted

to prevent any risk of the rear nut (or Fixed IR Display or IS Barrier module

accessory) vibrating loose.

2.4 Installing using a spigot gland and auxiliary

junction box

This option is required where IRmax is to be connected to an existing Exd or Exe certified

auxiliary junction box.

Diagram 6: IRmax connected to the auxiliary junction box

2. Installation

10

Detecting

Gas Saving Lives

English

2.4.1 To fit IRmax to an auxiliary junction box:

a. Carefully remove the outer section of the spigot gland (item 8 in Diagram 3 on

page 5).

b. Screw the narrow end of the spigot gland into the auxiliary junction box.

c. Raise the IRmax to the auxiliary junction box and pass the wires through the

assembly and into the auxiliary junction box. Secure the IRmax by screwing the

collar tightly to the cable gland. Tighten grub screw.

d. The main body of the IRmax can be swivelled horizontally at any angle, provided

it is mechanically secure, does not interfere with other equipment and is

accessible for maintenance.

e. Refer to Section 2.6 for instructions on wiring. See also Diagram 4 on page 7.

2.5 Cabling requirement

Cabling to IRmax must be in accordance with the recognised standards of the appropriate

authority in the country concerned and meet the electrical requirements of the IRmax.

Crowcon recommends the use of steel wire armoured (SWA) cable and suitable explosion

proof glands must be used. Alternative cabling techniques, such as steel conduit, may be

acceptable provided appropriate standards are met.

The maximum recommended cable length is 3.4 km (see Table 1).

IRmax requires a dc supply of 12-30Vdc. Ensure there is a minimum of 12V at the IRmax

from the control panel, taking into account the voltage drop due to cable resistance at a

peak current of 0.1A.

A 1.5mm

2

cable will typically allow cable runs up to 3.0km. Table 1 below shows the

maximum cable distances for typical cable parameters.

C.S.A. Resistance Max. Distance

>20 V

Max. Distance

18 to 20 V

mm

2

(Ohms per km) (km) (km)

1.0 18.4 2.2 1.6

1.5 13.0 3.0 2.3

2.5 11.5 3.4 2.6

Table 1: Maximum cable distances for typical cables

2. Installation

11

Detecting

Gas Saving Lives

English

2.6 Connections and settings

All connections described are with reference to the terminal block mounted within IRmax

connector main body. The terminals on the IRmax connector PCB are marked ‘+’, ‘sig’

and ‘0 V’. Correct polarity should be observed when connecting the IRmax to control

equipment.

IRmax is factory set as a ‘current sink’ device unless otherwise specified when ordering. To

reset to ‘current source’, remove the back nut and move the two links on the terminal PCB

from the ‘sink position to the ‘source’ position, as shown in Diagram 7.

Note: The external grounding terminal is only to be used where local authorities

permit or require such a connection. Where possible, to limit radio frequency

interference, the auxiliary junction box and cable armour should be grounded at

the control panel (safe area) only to avoid earth loops.

Diagram 7: Sink/source jumper location

The 4-20mA signal can be set to current 'Sink' or 'Source' using the pins and jumper link

shown in Diagram 7. Set to current 'Sink' by fitting the jumper link to pins 3 and 4 as

shown on the left-hand photograph. Set to current 'Source' by fitting the jumper link to

pins 1 and 2 as shown on the right-hand photograph. IRmax will be set to current 'Sink'

unless specified otherwise when ordering.

LED indication: an LED is fitted to the terminal PCB to indicate the current

operating status. Refer to Section 6 on page 17 for more information.

CONTROLLER

EARTH

+V

0V

Sg

3

21

Wiring

Number Colour Function

1 Red +V

2 Black 0V

3 Green Signal

Jumper

settings

Sink

setting

Source

setting

IR Display

connector

PC communications

kit connector

Status LED

12

Detecting

Gas Saving Lives

English

3. Operation

WARNING

Prior to carrying out any work ensure local regulations and site procedures are

followed. Never attempt to open the IRmax or auxiliary junction box when

flammable gas is present. Ensure that the associated control panel is inhibited so

as to prevent false alarms.

3.1 Commissioning procedure

1. Check that:

a. The cable connections are correct

b. The supply voltage is set at the control card as 18 to 30 V. The voltage measured

at the IRmax terminals (within the Exe auxiliary junction box if used, or at the

IRmax terminal PCB) and must be set between 12 and 30 V.

c. The links are set for 4-20 mA sink or source as appropriate to control card.

2. Once powered up leave IRmax for 30 minutes before attempting zero/cal. This delay is

to ensure thermal stability. (Note: IRmax will be fully operational from 30 seconds

after power is applied.)

3. Ensure clean air (i.e. no hydrocarbon gas) before zeroing. Zero reading at control card

(refer to control card instructions).

4. Fit a calibration cap over weatherproof cover to isolate measurement chamber from

ambient air. Such a cap is available from Crowcon (M041007). Connect calibration gas

(50% LEL nom) and apply at 1 litre-per-minute flow.

5. After 30 seconds adjust cal/span on control card so that display reads 50% LEL, or

matches concentration of calibration gas applied. The IRmax itself should not require

calibration.

6. Remove gas and calibration cap. Re-check zero.

7. At installation, or after the mirror has been changed, the IRmax can be zeroed

and calibrated either using an IR Display accessory (see page 1) or via a PC

communications kit (see the IRmax Accessories manual).

Note: ATEX Certified IRmax will be supplied calibrated for compliance with

EN61779 (where, for example 100% LEL Methane = 4.4% volume).

Note: It is recommended that the calibration cap is used for initial commissioning.

Subsequent calibrations may be conducted by applying gas to the weatherproof

cap remotely via the pipe spigot (thus avoiding the need to directly access the

IRmax). Calibration without the calibration cap (i.e. directly via the weatherproof

cap) can be performed provided local windspeed is below 2 metres/second. The

flow rate of the gas must be greater than 2.0 litre/minute.

3. Operation

13

Detecting

Gas Saving Lives

English

3.2 Routine maintenance

Site practices will dictate the frequency with which detectors are tested. Crowcon

recommends that IRmax is gas tested at least every 6 months and re-calibrated as

necessary. To re-calibrate an IRmax follow the steps given in Section 3.1.

In the event of an electronic failure please consult your local Crowcon representative.

Calibration interval: Crowcon recommend calibration every 12 months.

Remote calibration via pipe: Wind speed should be less than 2.0 metres per second. If

greater, use the calibration cap to prevent gas dilution.

Cleaning of optics: Is not recommended unless the IRmax is in obscuration

fault. If the window or mirror become contaminated, clean

carefully with the IPA impregnated wipes and/or the soft

cloth supplied in the mirror cleaning kit (see Section 5,

Accessories and spare parts on page 16).

Mirrors: If the mirror is damaged, obtain a mirror replacement

kit (see Section 5, Accessories and spare parts on

page 16). The IRmax must always be re-zeroed and

re-calibrated after mirror replacement.

If condensation starts to cause faults replace mirror

(optical coating may be damaged). Crowcon recommends

replacing mirror every 5 years.

3.3 Changing gas types

Each IRmax is supplied pre-calibrated for a particular type of gas (for example methane

or propane). If re-calibration for a different gas type is required, the IRmax can be

re-configured using the PC communications kit (see Section 5, Accessories and spare

parts on page 16), and then calibrated.

3. Operation

14

Detecting

Gas Saving Lives

English

3.4 Relative responses of gas types

The graph below shows the relative responses to other gas types for an IRmax calibrated

on methane.

Note: many hydrocarbon gases and vapours are more easily detected by IR

detectors than methane. The response of IRmax (and other IR gas detectors) will be

linear across the 0-100%LEL range for the target gas (ie methane in this example),

but non-linear for other hydrocarbons that may also be present.

Diagram 8

The diagram shows the approximate response of the gases mentioned above: from left to

right, butane, propane, pentane, hexane & petrol vapour and methane.

Other gas types and ranges are available. Please contact Crowcon for further details.

15

Detecting Gas Saving Lives

English

4. Specification

Enclosure material 316 Stainless Steel

Dimensions

(Detector only)

158mm x 75mm x 57mm (6.2 x 2.9 x 2.3 ins) (without

spigot)

Weight IRmax 1.58kg (3.5lbs)

IRmax with Fixed IR Display 2kg (4.4lbs)

IRmax with IS Barrier Module 2.4kg (5.3lbs)

Remote IR Display 0.2kg (0.4lbs)

Operating voltage 12Vdc to 30V dc

Power < 1 W

Output 3-wire 4-20 mA (Sink or Source)

Fault signal <1 mA

Maximum cable loop

resistance

80 Ohms (relative to –ve terminal)

Operating temperature -40°C to +75°C (-40°F to +167°F)

Humidity 0–100% Relative Humidity

Degree of protection IP66

Explosion protection Flameproof

Approval code

ATEX

IRmax (without IR Display)

II 2 GD Exd db IIC T6 Gb (Tamb = -40°C to +50°C)

II 2 GD Exd db IIC T4 Gb (Tamb = -40°C to +75°C)

II 2 GD Ex tb IIIC T135°C Db (-40°C ≤ Ta≤ +75°C)

IRmax with IS Barrier module (remote display)

II 2 GD Exd db ia IIC T4 Gb (Tamb = -40°C to +75°C)

Ex tb ia IIIC T135°C Db (Tamb = -40°C to +40°C)

IRmax (with Fixed IR Display)

II 2 G Exd db ia IIC T4 Gb (Tamb = -40°C to +75°C)

Safety certiﬁcate no.

ATEX and IECEx

IRmax (without IR Display):

Baseefa 09ATEX0206X and IECEx BAS.09.0109X

IRmax (with IR Display):

Baseefa 09ATEX0220X and IECEx BAS.09.0104X

Functional Safety Certiﬁed for use in a SIL 2 system.

Certiﬁcate number: Sira 12ATEX1206X

Standards EN 60079-0:2012+A11:2013, EN 60079-1:2014,

EN 60079-31:2014

IEC 60079-0:2011, IEC 60079-1:2014, IEC 60079-31:2013

EN 60079-29-1:2007, IEC 61508:2010, EN50402:2005

Zones Certiﬁed for use in Zone 1 or Zone 2

EMC EN50270

16

Detecting

Gas Saving Lives

English

5. Accessories and spare parts

Part Numbers Name Description

M041007 Calibration cap Fits over the standard weathercap

to enable calibration where local air

speed exceeds 2 metres per second.

S012130 Mounting bracket kit Enables mounting to a wall or 2"

(50 mm) pipe. Not required if IRmax

is being ﬁtted to an existing auxiliary

junction box.

S012152 Sun shade/Collector

cone

Can be ﬁtted to IRmax to protect

against elevated temperatures due

to direct sunlight and/or to extend

the detectors footprint for detecting

lighter than air gases (e.g. methane).

S012169 Duct mounting kit Enables monitoring of ducts from

300 mm to 3000 mm, and air-ﬂow

between 2 m/s and 20 m/s.

S012996 Flow adaptor For gas sampling applications.

S012827 PC communications

kit

Communications module, software

and lead to enable conﬁguration of

the detector.

M20: S012295

½” NPT: S012296

Auxiliary junction box Mounting option for IRmax for use in

hazardous environments.

C011210 Mirror cleaning kit Contains IPA impregnated wipes and

microﬁbre cloth

IRmax Spares

Refer to Diagram 3 on page 5 for details of spare parts.

La pagina sta caricando ...

Crowcon IRmax Installation, Operating And Maintenance Instruction

Crowcon IRmax Installation, Operating And Maintenance Instruction

in altre lingue

Documenti correlati

Altri documenti