Yamaha DVD-S559 Manuale del proprietario

Categoria
Lettori DVD
Tipo
Manuale del proprietario
G
DVD-S559
DVD PLAYER
LECTEUR DE DVD
OWNER'S MANUAL
MODE D'EMPLOI
01_DVD-S559_En.book Page 0 Friday, November 18, 2005 4:32 PM
1
En
1
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2
Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, or cold. In a
cabinet, allow about 2.5 cm (1 inch) of free space
all around this unit for adequate ventilation.
3
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in
an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5
Avoid installing this unit in a location where
foreign objects may fall onto this unit or where
this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or personal
injury.
Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
6
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
7
Do not plug in this unit to a wall outlet until all
connections are complete.
8
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9
Do not use excessive force on switches, knobs
and/or cords.
10
When disconnecting the power cord from the
wall outlet, grasp the plug; do not pull the cord.
11
Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12
Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from
use of this unit with a voltage other than as
specified.
13
To prevent damage by lightning, keep the power
cord out and outdoor antennas disconnected
from a wall outlet or the unit during a lightning
storm.
14
Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reason.
15
When not planning to use this unit for long
periods of time (i.e., vacation), disconnect the AC
power plug from the wall outlet.
16
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that
this unit is faulty.
17
Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect the
AC power plug from the wall outlet.
18
Install this unit near the AC outlet and where the
AC power plug can be reached easily.
LASER SAFETY
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the
cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open.
Avoid direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not
place your eyes close to the opening of the disc tray
and other openings or look inside.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
01_DVD-S559_En.book Page 1 Friday, November 18, 2005 4:32 PM
Contents
01
2
En
English
Thank you for purchasing this YAMAHA product.
Please read through this owner’s manual so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future
reference
.
Contents
01 Before you start
Features
. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
What’s in the box
. . . . . . . . . . . . . . . . . . . . 4
Hints on installation
. . . . . . . . . . . . . . . . . . 5
Disc/content format playback compatibility
5
02 Connecting up
Easy connections
. . . . . . . . . . . . . . . . . . . . 8
Connecting using a SCART AV cable
. . . . . 9
Connecting using the S-video output
. . . . . 9
Connecting using the component video
output
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to an AV receiver
. . . . . . . . . . 11
03 Controls and displays
Front panel
. . . . . . . . . . . . . . . . . . . . . . . . 12
Remote control
. . . . . . . . . . . . . . . . . . . . 13
04 Getting started
Switching on
. . . . . . . . . . . . . . . . . . . . . . 14
Using the on-screen displays
. . . . . . . . . . 14
Setting up the player for your TV
. . . . . . . . 15
Setting the language of this player’s
on-screen displays
. . . . . . . . . . . . . . . . . . 15
Playing discs
. . . . . . . . . . . . . . . . . . . . . . 16
05 Playing discs
Scanning discs
. . . . . . . . . . . . . . . . . . . . .20
Playing in slow motion
. . . . . . . . . . . . . . . .20
Frame advance/frame reverse
. . . . . . . . . .21
Viewing a JPEG slideshow
. . . . . . . . . . . . .21
Browsing DVD or Video CD/Super VCD disc
with the Disc Navigator
. . . . . . . . . . . . . . .21
Browsing WMA, MP3, DivX video and
JPEG files with the Disc Navigator
. . . . . . .22
Looping a section of a disc
. . . . . . . . . . . .23
Using repeat play
. . . . . . . . . . . . . . . . . . . .23
Using random play
. . . . . . . . . . . . . . . . . .24
Creating a program list
. . . . . . . . . . . . . . .25
Searching a disc
. . . . . . . . . . . . . . . . . . . .26
Switching subtitles
. . . . . . . . . . . . . . . . . .26
Switching audio language/channels
. . . . .27
Zooming the screen
. . . . . . . . . . . . . . . . . .27
Switching camera angles
. . . . . . . . . . . . .27
Displaying disc information
. . . . . . . . . . . .27
06 Audio Settings and Video Adjust
menus
Audio Settings menu
. . . . . . . . . . . . . . . . .28
Video Adjust menu
. . . . . . . . . . . . . . . . . .29
01_DVD-S559_En.book Page 2 Friday, November 18, 2005 4:32 PM
Contents01
3
En
07 Initial Settings menu
Using the Initial Settings menu
. . . . . . . . .30
Digital Audio Out settings
. . . . . . . . . . . . .30
Video Output settings
. . . . . . . . . . . . . . . .31
Language settings
. . . . . . . . . . . . . . . . . . .31
Display settings
. . . . . . . . . . . . . . . . . . . . .32
Options settings
. . . . . . . . . . . . . . . . . . . .32
Parental Lock
. . . . . . . . . . . . . . . . . . . . . . .33
08 Additional information
Taking care of your player and discs
. . . . .35
Screen sizes and disc formats
. . . . . . . . . .36
Setting the TV system
. . . . . . . . . . . . . . . .37
Resetting the player
. . . . . . . . . . . . . . . . . .37
DVD-Video regions
. . . . . . . . . . . . . . . . . . .37
Selecting languages using the language
code list
. . . . . . . . . . . . . . . . . . . . . . . . . . .37
Language code list
. . . . . . . . . . . . . . . . . . .38
Country/Area code list
. . . . . . . . . . . . . . . .38
Glossary
. . . . . . . . . . . . . . . . . . . . . . . . . . .39
Specifications
. . . . . . . . . . . . . . . . . . . . . .40
01_DVD-S559_En.book Page 3 Friday, November 18, 2005 4:32 PM
Before you start
01
4
En
English
Chapter 1
Before you start
Features
24-bit/192kHz compatible DAC
The on-board 24-bit/192kHz DAC means that
this player is fully compatible with high
sampling-rate discs, capable of delivering
exceptional sound quality in terms of dynamic
range, low-level resolution and high-frequency
detail.
Excellent audio performance surround
sound entertainment with Dolby Digital
*1
and DTS
*2
software
Logos:
When connected to a suitable AV amplifier or
receiver, this player gives great surround
sound with Dolby Digital and DTS discs.
PureCinema Progressive Scan video
When connected to a progressive scan-
compatible TV or monitor using the
component video outputs, you can enjoy
extremely stable, flicker free images, with the
same frame refresh rate as the original movie.
New Disc Navigator with moving
pictures
The new Disc Navigator enables you play the
first few seconds of each title or chapter in a
thumbnail image on screen.
DSP effects for enhanced playback
See Audio Settings and Video Adjust menus on
page 28.
Picture zoom
See Zooming the screen on page 27.
MP3 and WMA compatibility
See Compressed audio compatibility on page 6.
JPEG compatibility
See JPEG file compatibility on page 7.
DivX video compatibility
See DivX video compatibility on page 7.
Energy saving design
An auto power-off function switches the player
into standby if not used for about 30 minutes.
*1
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
*2
“DTS” and “DTS Digital Out” are registered
trademarks of Digital Theater Systems Inc.
What’s in the box
Please confirm that the following accessories
are in the box when you open it.
Remote control
AA/R6 dry cell batteries x2
Audio/video cable (red/white/yellow plugs)
Power cable
Owner’s Manual
Putting the batteries in the remote
Open the battery compartment cover
and insert the batteries as shown.
Use two AA/R6 batteries and follow the
indications (, ) inside the compartment.
Close the cover when you’re finished.
01_DVD-S559_En.book Page 4 Friday, November 18, 2005 4:32 PM
Before you start01
5
En
Important
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe
the following:
Don’t mix new and old batteries together.
Don’t use different kinds of battery
together—although they may look similar,
different batteries may have different
voltages.
Make sure that the plus and minus ends of
each battery match the indications in the
battery compartment.
Remove batteries from equipment that
isn’t going to be used for a month or more.
When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Hints on installation
We want you to enjoy using this product for
years to come, so please use the following
guidelines when choosing a suitable location:
Do...
Use in a well-ventilated room.
Place on a solid, flat, level surface, such as
a table, shelf or stereo rack.
Don’t...
Use in a place exposed to high
temperatures or humidity, including near
radiators and other heat-generating
appliances.
Place on a window sill or a place where the
player will be exposed to direct sunlight.
Use in an excessively dusty or damp
environment.
Place directly on top of an amplifier, or
other component in your stereo system
that becomes hot in use.
Use near a television or monitor as you may
experience interference—especially if the
television uses an indoor antenna.
Use in a kitchen or other room where the
player may be exposed to smoke or steam.
Use on a thick rug or carpet, or cover with
cloth—this may prevent proper cooling of
the unit.
Place on an unstable surface, or one that is
not large enough to support all four of the
unit’s feet.
Disc/content format playback
compatibility
This player is compatible with a wide range of
disc types (media) and formats. Playable discs
will generally feature one of the following logos
on the disc and/or disc packaging. Note
however that some disc types, such as
recordable CD and DVD, may be in an
unplayable format—see below for further
compatibility information.
Please also note that recordable discs cannot be
recorded using this player.
is a trademark of Fuji Photo Film Co. Ltd.
Also compatible with KODAK Picture CD
DVD-Video DVD-R DVD-RW
DVD+Rewritable DVD+R DVD+RDL
Video CD
Fujicolor CD
Audio CD CD-R CD-RW
DVD+R DL
DVD+R
DVD+ReWritable
01_DVD-S559_En.book Page 5 Friday, November 18, 2005 4:32 PM
Before you start
01
6
En
English
This player supports the IEC’s Super VCD stan-
dard. Compared to the Video CD standard,
Super VCD offers superior picture quality, and
allows two stereo soundtracks to be recorded.
Super VCD also supports the widescreen size.
CD-R/RW compatibility
Compatible formats: CD-Audio, Video CD/
Super VCD, ISO 9660 CD-ROM* containing
MP3, WMA, JPEG or DivX video files
* ISO 9660 Level 1 or 2 compliant. CD
physical format: Mode1, Mode2 XA Form1.
Romeo and Joliet file systems are both
compatible with this player.
Multi-session playback: No
Unfinalized disc playback: No
File structure (may differ): Up to 299 folders
on a disc; up to 648 folders and files
(combined) within each folder
DVD+R/RW, DVD-R/RWcompatibility
Compatible formats: DVD-Video, Video
Recording (VR)*
* DVD-RW only. Edit points may not play
exactly as edited; screen may go
momentarily blank at edited points.
Unfinalized playback: No
WMA/MP3/JPEG file playback on DVD+R/
RW, DVD-R/RW: No
Compressed audio compatibility
Compatible formats: MPEG-1 Audio Layer 3
(MP3), Windows Media Audio (WMA)
Sampling rates: 32, 44.1 or 48kHz
Bit-rates: Any (128Kbps or higher
recommended)
VBR (variable bit rate) MP3 playback: No
VBR WMA playback: No
WMA lossless encoding compatible: No
DRM (Digital Rights Management)
compatible: Yes (DRM-protected audio
files will not play in this player—see also
DRM in the Glossary on page 39)
File extensions: .mp3, .wma (these must be
used for the player to recognize MP3 and
WMA files – do not use for other file types)
About WMA
The Windows Media
®
logo indicates that this
player can playback Windows Media Audio
content.
WMA is an acronym for Windows Media Audio
and refers to an audio compression technology
developed by Microsoft Corporation. WMA
content can be encoded by using Windows
Media
®
Player version 7, 7.1, Windows Media
®
Player for Windows
®
XP, or Windows Media
®
Player 9 Series.
Microsoft, Windows Media, and the Windows
logo are trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
About DivX
DivX is a compressed digital video format
created by the DivX
®
video codec from
DivXNetworks, Inc. This player can play DivX
video files burned on CD-R/RW/ROM discs.
Keeping the same terminology as DVD-Video,
individual DivX video files are called "Titles".
When naming files/titles on a CD-R/RW disc
prior to burning, keep in mind that by default
they will be played in alphabetical order.
Super VCD
01_DVD-S559_En.book Page 6 Friday, November 18, 2005 4:32 PM
Before you start01
7
En
Displaying DivX subtitle files
The font sets listed below are available for DivX
external subtitle files. You can see the proper
font set on-screen by setting the Subtitle
Language (in Language settings on page 31)
to match the subtitle file.
This player supports the following language
groups:
Group 1: Albanian (sq), Basque (eu), Catalan (ca),
Danish (da), Dutch (nl), English (en), Faroese (fo),
Finnish (fi), French (fr), German (de), Icelandic (is), Irish
(ga), Italian (it), Norwegian (no), Portuguese (pt), Rhaeto-
Romanic (rm), Scottish (gd), Spanish (es), Swedish (sv)
Group 2: Albanian (sq), Croatian (hr), Czech (cs),
Hungarian (hu), Polish (pl), Romanian (ro), Slovak (sk),
Slovenian (sl)
Group 3: Bulgarian (bg), Byelorussian (be), Macedonian
(mk), Russian (ru), Serbian (sr), Ukrainian (uk)
Group 4: Hebrew (iw), Yiddish (ji)
Group 5: Turkish (tr)
DivX, DivX Certified, and associated logos are
trademarks of DivXNetworks, Inc. and are used
under license.
Some external subtitle files may be
displayed incorrectly or not at all.
For external subtitle files the following
subtitle format filename extensions are
supported (please note that these files are
not shown within the disc navigation
menu): .srt, .sub, .ssa, .smi
The filename of the movie file has to be
repeated at the beginning of the filename
for the external subtitle file.
The number of external subtitle files which
can be switched for the same movie file is
limited to a maximum of 10.
DivX video compatibility
Official DivX
®
Certified product.
Plays DivX
®
5, DivX
®
4, DivX
®
3 and DivX
®
VOD video content (in compliance with
DivX
®
Certified technical requirements).
File extensions: .avi and .divx (these must
be used for the player to recognize DivX
video files). Note that all files with the .avi
extension are recognized as MPEG4, but not
all of these are necessarily DivX video files
and therefore may not be playable on this
player.
DivX, DivX Certified, and associated logos are
trademarks of DivXNetworks, Inc. and are used
under license.
JPEG file compatibility
Compatible formats: Baseline JPEG and
EXIF 2.2* still image files up to a resolution
of 3072 x 2048.
*File format used by digital still cameras
Progressive JPEG compatible: No
File extensions: .jpg (must be used for the
player to recognize JPEG files – do not use
for other file types)
PC-created disc compatibility
Discs recorded using a personal computer
may not be playable in this unit due to the
setting of the application software used to
create the disc. In these particular instances,
check with the software publisher for more
detailed information.
Discs recorded in packet write mode (UDF
format) are not compatible with this player.
Check the DVD+R/RW, DVD-R/RW or CD-R/
RW software disc boxes for additional
compatibility information.
01_DVD-S559_En.book Page 7 Friday, November 18, 2005 4:32 PM
Connecting up
02
8
En
English
Chapter 2
Connecting up
Easy connections
The setup described here is a basic setup that allows you to play discs using just the cables
supplied with the player. In this setup, stereo audio is played through the speakers in your TV.
Important
This player is equipped with copy protection technology. Do not connect this player to your TV
via a VCR using audio/video or S-video cables, as the picture from this player will not appear
properly on your TV. (This player may also not be compatible with some combination TV/VCRs
for the same reason; refer to the manufacturer for more information.)
To power
outlet
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
AV
L
R
AC IN
Yellow
White
Red
TV
A/V IN
01_DVD-S559_En.book Page 8 Friday, November 18, 2005 4:32 PM
Connecting up02
9
En
1 Connect the VIDEO OUT and AUDIO
OUT L/R jacks to a set of A/V inputs on your
TV.
Use the supplied audio/video cable,
connecting the red and white plugs to the
audio outputs and the yellow plug to the video
output. Make sure you match up the left and
right audio outputs with their corresponding
inputs for correct stereo sound.
See below if you want to use a component or
S-video cable for the video connection.
2 Connect the supplied AC power cable to
the AC IN inlet, then plug into a power
outlet.
Note
Before unplugging the player from the
power outlet, make sure you first switch it
into standby using either the front panel
STANDBY/ON button, or the remote
control, and wait of the -OFF- message to
disappear from the player’s display.
For the above reasons, do not plug this
player into a switched power supply found
on some amplifiers and AV receivers.
Connecting using a SCART AV
cable
A SCART-type AV connector is provided for
connection to a TV or AV receiver. The video
output is switchable between ordinary
composite and RGB. See AV Connector Out on
page 31 for how to set it.
The SCART AV connector also outputs analog
audio, so there is no need to also connect the
AUDIO OUT L/R jacks.
1 Use a SCART cable (not supplied) to
connect the AV CONNECTOR (RGB) output
to a SCART AV input on your TV (or AV
receiver).
Connecting using the S-video
output
If your TV (or other equipment) has an S-video
(S1) input, you can use the S-video output on
this player instead of the standard (composite)
output for a better quality picture.
Use an S-video cable (not supplied) to
connect the S-VIDEO OUT to an S-video
input on your TV (or monitor or AV
receiver).
Line up the small triangle above the jack with
the same mark on the plug before plugging in.
U
T
Y
COMPONENT
VIDEO
AUDIO OUT
AV
L
R
TV
SCART
01_DVD-S559_En.book Page 9 Friday, November 18, 2005 4:32 PM
Connecting up
02
10
En
English
Connecting using the
component video output
You can use the component video output
instead of the standard video out jack to
connect this player to your TV (or other
equipment). This should give you the best
quality picture from the three types of video
output available.
Use a component video cable (not
supplied) to connect the COMPONENT
VIDEO OUT jacks to a component video
input on your TV, monitor or AV receiver.
Watching progressive scan video
from the component video outputs
This player can output progressive scan video
from the component video output. Compared
to interlace video, progressive scan video
effectively doubles the scanning rate of the
picture, resulting in a very stable, flicker-free
image.
To set up the player for use with a progressive
scan TV, see Video Output settings on page 31.
When the player is set to output progressive
scan video, the PRGSVE indicator lights in the
front panel display.
Important
If you connect a TV that is not compatible
with a progressive scan signal and switch
the player to progressive, you will not be
able to see any picture at all. In this case,
switch everything off and reconnect using
the supplied video cable (see Easy
connections on page 8), then switch back
to Interlace (see below).
Switching the video output to interlace
using the front panel controls
Switch the player to standby then, using the
front panel controls, press STANDBY/ON
while pressing to switch the player back to
Interlace.
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
TV
S-VIDEO
IN
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
TV
COMPONENT
VIDEO IN
STANDBY/ON
DVD-S559
01_DVD-S559_En.book Page 10 Friday, November 18, 2005 4:32 PM
Connecting up02
11
En
Compatibility of this player with
progressive-scan and high-definition TVs
This player is compatible with progressive
video Macro Vision System Copy Guard.
Consumers should note that not all high-
definition television sets are fully compatible
with this product and may cause artifacts to be
displayed in the picture. In case of 525/625
progressive scan picture problems, it is
recommended that the user switch the
connection to the ‘standard definition’ output
(Interlace). If there are questions regarding our
TV set compatibility with this model, please
contact our customer service center.
This player is fully compatible with the
complete line of YAMAHA products, including
the projectors DPX-1200, LPX-510 and the
plasma monitor PDM-4220.
Connecting to an AV receiver
To enjoy multichannel surround sound you
need to connect this player to an AV receiver
using the digital audio output.
In addition to a digital connection, we
recommend also connecting using the stereo
analog connection.
You’ll probably also want to connect a video
output to your AV receiver. You can use any of
the video outputs available on this player (the
illustration shows a standard (composite)
connection).
1 Connect the DIGITAL AUDIO OUT
COAXIAL jack on this player to a coaxial
digital input on your AV receiver.
Use a coaxial cable (similar to the supplied
video cable) to connect the COAXIAL DIGITAL
AUDIO OUT jack to a coaxial input on your AV
receiver.
2 Connect the analog AUDIO OUT L/R and
VIDEO OUT jacks on this player to a set of
analog audio and video inputs on your AV
receiver.
You can use the SCART AV connector, or
the S-video or component video jacks to
connect to the AV receiver if you prefer.
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
AV receiver
DIGITAL IN
(COAXIAL)
AV receiver
DIGITAL OUT VIDEO OUT
S VIDEO
P
R
/C
R
Y
P
B
/C
B
COAXIAL
PCM/q DIGITAL
/DTS/MPEG
COMPONENT
VIDEO
AUDIO OUT
L
R
AUDIO/
VIDEO IN
01_DVD-S559_En.book Page 11 Friday, November 18, 2005 4:32 PM
Controls and displays
03
12
En
English
Chapter 3
Controls and displays
Front panel
1 STANDBY/ON (page 14)
2 Disc tray
3 (page 17)
4 (page 17)
5 and (page 17)
6 (page 16)
7 Display
8 (page 17)
DVD-S559
1
2
5
3 4
6 7
8
01_DVD-S559_En.book Page 12 Friday, November 18, 2005 4:32 PM
Controls and displays03
13
En
Remote control
1(STANDBY/ON) (page 14)
2 Number buttons (page 17)
3 PLAY MODE (page 23)
4 SURROUND (page 28)
5 TOP MENU (page 18)
6 ENTER & cursor buttons (page 14)
7 HOME MENU (page 14)
8 SUBTITLE (page 26)
9 ANGLE (page 27)
10 and (SKIP) (page 17)
11 (STOP) (page 17)
12 OPEN/CLOSE (page 16)
13 ENTER (page 14)
14 CLEAR (page 25)
15 ON SCREEN (page 27)
16 MENU (page 18)
17 RETURN (page 14)
18 AUDIO (page 27)
19 ZOOM (page 27)
20 and (SLOW/SEARCH)
(page 17, 20
)
21 (PLAY) (page 17)
22 (PAUSE) (page 17)
Using the remote control
Keep in mind the following when using the
remote control:
Make sure that there are no obstacles
between the remote and the remote sensor
on the unit.
The remote has a range of about 7m.
Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this unit.
Replace the batteries when you notice a
fall off in the operating range of the remote.
5
2
4
9
10
7
6
8
11
1
3
12
13
15
16
17
18
21
22
14
19
20
STANDBY/ON
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIP
SKIP
SLOW/SEARCH
SLOW/SEARCH
STOP
STOP
PAUSE
PAUSE
PLAY
PLAY
ENTER
ENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 13 Friday, November 18, 2005 4:32 PM
Getting started
04
14
En
English
Chapter 4
Getting started
Switching on
After making sure that everything is connected
properly and that the player is plugged in,
press STANDBY/ON on the front panel or
remote control to switch the player on.
Also, switch on your TV and make sure that it is
set to the input you connected the DVD player
to.
FAQ
My DVD player switches on but there is
nothing displayed on my TV.
Make sure that the TV is set to the correct
video input (not a TV channel). For
example, if you connected this player to the
VIDEO 1 inputs on your TV, switch your TV
to VIDEO 1.
Note
This player features a screen saver and an
auto power off function. If the player is
stopped and no button is pressed for
around five minutes, the screen saver
starts. If the disc tray is closed but no disc
is playing and no control is pressed for
about 30 minutes, the player automatically
goes into standby.
Using the on-screen displays
For ease of use, this player makes extensive
use of graphical on-screen displays (OSDs).
All the screens are navigated in basically the
same way, using the cursor buttons
() to change the highlighted item and
pressing ENTER to select it.
Note
From here on in this manual, the word
‘select’ generally means use the cursor
buttons to highlight an item on-screen,
then press ENTER.
STANDBY/ON
DVD-S559
Button What it does
HOME
MENU
Display/exit the on-screen display.
Changes the highlighted menu
item.
ENTER
Selects the highlighted menu
item (both
ENTER buttons on the
remote work in exactly the same
way).
RETURN Returns to the main menu
without saving changes.
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIPSKIP SLOW/SEARCHSLOW/SEARCH
STOP PAUSE PLAY
ENTER
ENTER
5
9
78
6
0
01_DVD-S559_En.book Page 14 Friday, November 18, 2005 4:32 PM
Getting started04
15
En
Setting up the player for your
TV
If you have a widescreen (16:9) TV, you should
setup the player so that the picture will be
presented correctly. If you have a conventional
(4:3) TV, you can leave the player on the default
setting and move on to the next section.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘TV Screen’ from the ‘Video
Output’ settings.
3 If you have a widescreen (16:9) TV,
select ‘16:9 (Wide)’.
If you have a conventional (4:3) TV, you can
change the setting from 4:3 (Letter Box) to 4:3
(Pan & Scan) if you prefer. See Video Output
settings on page 31 for more details.
4 Press HOME MENU to exit the menu
screen.
Setting the language of this
player’s on-screen displays
This sets the language of the player’s on-
screen displays.
1 Press HOME MENU and select ‘Initial
Settings’.
2 Select ‘OSD Language’ from the
‘Display’ settings.
3 Select a language.
The on-screen language will change according
to your selection.
4 Press HOME MENU to exit the menu
screen.
Initial Settings
Digital Audio Out
Video Outpu
t
Language
Display
Options
TV Screen
Component Out
AV Connector Out
4:3 (Letter Box)
4:3 (Pan&Scan)
16:9 (Wide)
Initial Settings
Initial Settings
Digital Audio Out
Video Output
Language
Display
Options
OSD Language
Angle Indicator
English
français
Deutsch
Italiano
Español
Initial Settings
01_DVD-S559_En.book Page 15 Friday, November 18, 2005 4:32 PM
Getting started
04
16
En
English
Playing discs
The basic playback controls for playing DVD,
CD, Video CD/Super VCD, DivX video and MP3/
WMA discs are covered here. Further functions
are detailed in the next chapter.
For details on playing JPEG picture discs, see
Viewing a JPEG slideshow on page 21.
Important
Throughout this manual, the term ‘DVD’
means DVD-Video, DVD+R/RW and DVD-
R/RW. If a function is specific to a
particular kind of DVD disc, it is specified.
1 If the player isn’t already on, press
(STANDBY/ON) to switch it on.
If you’re playing a DVD, disc containing DivX
video files or Video CD/Super VCD, also turn on
your TV and make sure that it is set to the
correct video input.
2 Press OPEN/CLOSE () to open the disc
tray.
3 Load a disc.
Load a disc with the label side facing up, using
the disc tray guide to align the disc (if you’re
loading a double-sided DVD disc, load it with
the side you want to play face down).
4 Press (play) to start playback.
If you’re playing a DVD or Video CD/Super VCD,
an on-screen menu may appear. See DVD-
Video disc menus on page 18 and Video CD/
Super VCD PBC menus on page 18 for more on
how to navigate these.
If you’re playing a containing DivX video
files or MP3/WMA audio files, it may take a
few seconds before playback starts, etc.
This is normal.
Note
You may find with some DVD discs that
some playback controls don’t work in
certain parts of the disc. This is not a
malfunction.
If a disc contains a mixture of DivX video
and other media file types (MP3, for
example), first select whether to play the
DivX video files (DivX)or the other media
file types (MP3 / WMA / JPEG) from the
on-screen display.
STANDBY/ON
CLEAR
OPEN/CLOSE
ENTER
PLAY MODE
SURROUND
ON SCREEN
MENU
TOP MEN
SUBTITLE
HOME
MENU
RETURN
ANGLE
ZOOM
AUDIO
SKIP
SLOW/SEARCH
STOP
PAUS E
PLAY
ENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 16 Friday, November 18, 2005 4:32 PM
Getting started04
17
En
Basic playback controls
The table below shows the basic controls on
the remote for playing discs. The following
chapter covers other playback features in more
detail.
Resume and Last Memory
When you stop playback of a DVD, CD, Video
CD/Super VCD or DivX video discs, RESUME is
shown in the display indicating that you can
resume playback again from that point.
If the disc tray is not opened, the next time you
start playback the display shows RESUME and
playback resumes from the resume point. (If
you want to clear the resume point, press
(stop) while RESUME is displayed.)
With DVDs and Video CD/ Super VCDs, if you
take the disc out of the player after stopping
playback, the last play position is stored in
memory. If the next disc you load is the same
one, the display shows LAST MEM and
playback will resume. For DVD-Video discs, the
player stores the play position of the last five
discs. When one of these discs is next loaded,
you can resume playback.
Note
The Last Memory function doesn’t work
with VR format DVD-RW discs.
If you don’t need the Last Memory function
when you stop a disc, you can press OPEN/
CLOSE () to stop playback and open the
disc tray.
Button What it does
Starts playback.
If the display shows RESUME or
LAST MEM playback starts from the
resume or last memory point (see
also Resume and Last Memory
below.)
Pauses a disc that’s playing, or
restarts a paused disc.
Stops playback.
See also Resume and Last Memory
below.
(remote
only)
Press to start fast reverse scanning.
Press
(play) to resume normal
playback.
(remote
only)
Press to start fast forward scanning.
Press (play) to resume normal
playback.
Skips to the start of the current
track, title or chapter, then to
previous tracks/titles/chapters.
Skips to the next track, title or
chapter.
Numbers
(remote
only)
Use to enter a title/chapter/track
number. Press
ENTER to select.
• If the disc is stopped, playback
starts from the selected title (for
DVD) or track (for CD/Video CD
/
Super VCD
).
• If the disc is playing, playback
jumps to the start of the selected
title (VR mode DVD-RW), chapter
(DVD-Video) or track (CD/Video CD/
Super VCD).
01_DVD-S559_En.book Page 17 Friday, November 18, 2005 4:32 PM
Getting started
04
18
En
English
DVD-Video disc menus
Many DVD-Video discs feature menus from
which you can select what you want to watch.
They may also give access to additional
features, such as subtitle and audio language
selection, or special features such as
slideshows. See the disc packaging for details.
Sometimes DVD-Video menus are displayed
automatically when you start playback; others
only appear when you press MENU or TOP
MENU.
Video CD/Super VCD PBC menus
Some Video CD/Super VCDs have menus from
which you can choose what you want to watch.
These are called PBC (Playback control)
menus.
You can play a PBC Video CD/Super VCD
without having to navigate the PBC menu by
starting playback using a number button to
select a track, rather than the (play) button.
Button What it does
TOP MENU Displays the ‘top menu’ of a DVD
disc—this varies with the disc.
MENU Displays a DVD disc menu—this
varies with the disc and may be
the same as the ‘top menu’.
Moves the cursor around the
screen.
ENTER Selects the current menu option.
RETURN Returns to the previously dis-
played menu screen.
Numbers
(remote
only)
Highlights a numbered menu
option (some discs only). Press
ENTER to select.
STANDBY/ON
CLEAR
CLEAR
OPEN/CLOSE
ENTER
ENTER
PLAY MODE
PLAY MODE
SURROUND
SURROUND
ON SCREEN
ON SCREEN
MENU
MENU
TOP MEN
TOP MENU
SUBTITLE
SUBTITLE
HOME
HOME
MENU
MENU
RETURN
RETURN
ANGLE
ANGLE
ZOOM
ZOOM
AUDIO
AUDIO
SKIP SLOW/SEARCH
STOP PAUSE PLAY
ENTER
ENTER
21
5
9
3
7
4
8
6
0
Button What it does
RETURN Displays the PBC menu.
Numbers
(remote
only)
Use to enter a numbered menu
option. Press
ENTER to select.
Displays the previous menu page
(if there is one).
Displays the next menu page (if
there is one).
STANDBY/ON
CLEARCLEAR
OPEN/CLOSE
ENTERENTER
PLAY MODEPLAY MODE SURROUNDSURROUND ON SCREENON SCREEN
MENUMENU
TOP MENTOP MENU
SUBTITLESUBTITLE
HOMEHOME
MENUMENU
RETURNRETURN
ANGLEANGLE ZOOMZOOM AUDIOAUDIO
SKIPSKIP SLOW/SEARCHSLOW/SEARCH
STOPSTOP PAUSEPAUSE PLAYPLAY
ENTERENTER
21
5
9
3
7
4
8
6
0
01_DVD-S559_En.book Page 18 Friday, November 18, 2005 4:32 PM
Getting started04
19
En
FAQ
After I load a DVD disc, it ejects
automatically after a few seconds!
Most likely, the disc is the wrong region for
your player. The region number should be
printed on the disc; check it against the
region number of the player (which you can
find on the rear panel). See also DVD-Video
regions on page 37.
If the region number is OK, it may be that
the disc is damaged or dirty. Clean the disc
and look for signs of damage. See also
Taking care of your player and discs on
page 35.
Why won’t the disc I loaded play?
First check that you loaded the disc the
right way up (label side up), and that it’s
clean and undamaged. See Taking care of
your player and discs on page 35 for
information on cleaning discs.
If a disc loaded correctly won’t play, it’s
probably an incompatible format or disc
type, such as DVD-Audio or DVD-ROM. See
Disc/content format playback compatibility
on page 5 for more on disc compatibility.
•I have a widescreen TV so why are there
black bars at the top and bottom of the
screen when I play some discs?
Some movie formats are such that even
when played on a widescreen TV, black
bars are necessary at the top and bottom of
the screen. This is not a malfunction.
•I have a standard (4:3) TV and set the player
to show widescreen DVDs in pan & scan
format, so why do I still get black bars top
and bottom with some discs?
Some discs override the display
preferences of the player, so even if you
have 4:3 (Pan & Scan) selected, those
discs will still be shown in letter box format.
This is not a malfunction.
01_DVD-S559_En.book Page 19 Friday, November 18, 2005 4:32 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42

Yamaha DVD-S559 Manuale del proprietario

Categoria
Lettori DVD
Tipo
Manuale del proprietario