DTS SCENA COMPACT LED 50 Manuale utente

SCENA LED 80 FC

Made in Italy

SCENA LED 80 FR FC

SCENA LED 80 PC FC

User’s Manual rel. 1.0 GB

D.T.S. Illuminazione s.r.l. – ITALY

http://www.dts-lighting.it/

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS ................................................................................................................. 4

2- GENERAL WARNING .............................................................................................. 4

3- GENERAL WARRANTY CONDITIONS .................................................................... 4

4- TECHNICAL FEATURES ......................................................................................... 5

5- ACCESSORIES ........................................................................................................ 6

6- IMPORTANT SAFETY INFORMATION .................................................................... 7

6.1 Fire prevention...................................................................................................... 7

6.2 Prevention of electric shock .................................................................................. 7

6.3 Safety ................................................................................................................... 7

6.4 Waste Electrical and Electronic Equipment directive ............................................ 7

7- INPUT / OUTPUT CONNECTIONS ........................................................................... 8

8- DMX SIGNAL CONNECTION ................................................................................... 9

8.1 DMX Addresses .................................................................................................. 10

8.2 Selecting the DMX address ................................................................................ 10

9- FIRMWARE UPDATING ......................................................................................... 10

10- DISPLAY FUNCTIONS ......................................................................................... 11

11- DMX PROTOCOL ................................................................................................. 17

4

!

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC SHOCK

RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS YOU CAN PLACE THE

UNIT ON NORMALLY FLAMMABLE SURFACES

THIS SYMBOL INDICATES THE MINIMUM

DISTANCE TO BE KEPT BETWEEN THE UNIT

AND THE ILLUMINATED OBJECTS

THIS SYMBOL INDICATES THE EUROPEAN

COMMUNITY DIRECTIVE 2002/96/EC ON WASTE

ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE)

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation , use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before maintenance.

The device must always be equipped with an efficient ground connection.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

LED 30 cm

5

4- TECHNICAL FEATURES

OVERVIEW

SCENA LED 80 FC is a compact, lightweight, DMX-controlled LED projector equipped

with an high-power Full Colour (RGBW) LED featuring 4 LED channels (Red / Green /

Blue / White); 3660 Total Lumens.

The unit in available in two models: SCENA LED 80 PC FC, featuring a Ø 90 mm PC

lens, and a long excursion 10°-76° linear zoom with high-efficiency optical system,

enabling it to be used as a PC Beam or a very wide Wash (4245 Lux / 2 m).

SCENA LED 80 FR FC, featuring a Ø 112 mm Fresnel lens, and a long excursion

14°-77° linear zoom (3864 Lux / 2 m) with high-efficiency optical system.

SCENA LED 80 FC is a modern alternative to conventional lights, improving light

quality, flexibility of use and installation, energy savings and component duration.

The fixture doesn’t heat up and the projection is always flicker free.

The dimming curves are similar to those of halogen lamps.

The connectors are Powercon In/Out and 5 poles DMX In/Out.

SCENA LED 80 FC is contained in a strong housing with folded edges, designed to

resist all the rigors of continuous use.

Also, the yoke has an exclusive round flange + clutch system which guarantees a

perfect grip and safer operation.

PRODUCT CODES:

03.TS026.03.A SCENA LED 80 FC *PC lens *White finishing

03.TS026.44.A SCENA LED 80 FC *PC lens *Grey Silver finishing

03.TS026.46.A SCENA LED 80 FC *PC lens *Black finishing

03.TS026.03.F SCENA LED 80 FC *Fresnel lens *White finishing

03.TS026.44.F SCENA LED 80 FC *Fresnel lens *Grey Silver finishing

03.TS026.46.F SCENA LED 80 FC *Fresnel lens *Black finishing

LED Technology

1 x FULL RGBW LED; 3660 Lumens

Optical group

PC version (Ø 90 mm PC lens), 4245 Lux / 2 m, 10° - 76° linear zoom

FR version (Ø 112 mm Fresnel lens), 3864 Lux / 2 m, 14° - 77° linear zoom

Control

10 DMX channels (Default)

4 digit 7 segments LED display + 4 soft keys

Connectors

Power supply: Powercon In & Out connectors

DMX: 5 poles In & Out connectors

Power supply

Electronic full-range 90-260Vac , 50/60 Hz

Consumption: max 90W

Weight

4 Kg (PC version)

3,7 Kg (FR version)

6

DIMENSIONS

5- ACCESSORIES

As standard

1 x User’s Manual

1 x POWERCON male cable connector (D.T.S. Code 0520P014)

1 x XLR 5 pins male cable connector (D.T.S. Code 0508B028)

1 x XLR 5 pins female cable connector (D.T.S. Code 0508B027)

1 x Filterframe for SCENA COMPACT *Black finish (D.T.S. Code 02M00422.46)

Optional (on request)

- “C” Clamp G50 (Max. Load. 10 Kg) *Black finish (D.T.S. Code 0521A012)

- “C” Clamp G60 (Max. Load. 50 Kg) *Black finish (D.T.S. Code 0521A004)

- Barndoor for SCENA COMPACT *Black finish (D.T.S. Code 03.TA206)

7

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

It is permissible to place the unit on normally flammable surfaces.

Suitable for mounting on normally flammable materials surfaces greater than 200°C

with some combustion time lag.

Minimum distance from the closest illuminable surface: 30 cm.

Replace any blown or damaged fuses only with those of identical value (2AT).

6.2 Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of

the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

The use of a thermal magnetic circuit breaker is recommended for each SCENA LED

80 FC unit. Use only AC supplies 90-260V , 50-60 Hz.

SCENA LED 80 FC should never be located in position exposed to rain or in areas of

extreme humidity.

A good air ventilation is essential for proper equipment work.

6.3 Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at least 5

minutes have elapsed since the unit was turned off.

Never install the unit in an enclosed area lacking sufficient air flow.

The ambient temperature should not exeed 40°C and should not be lower than -10°C.

6.4 Waste Electrical and Electronic Equipment (WEEE) directive:

The machine, accessories and packaging should be sorted for environmental-friendly

recycling.

For EC countries: according to the European Directive 2002/96/EC for Waste

Electrical and Electronic Equipment and its implementation into national right,

luminaires that are no longer usable must be collected separately and disposed

of in an environmentally correct manner.

!

8

7- INPUT / OUTPUT CONNECTIONS

FUSE 2AT

DMX OUTPUT

XLR 5 Pins Female Panel Connector

MAINS AC

INPUT

90-260V,

50/60 Hz

DMX INPUT

XLR 5 Pins Male Panel Connector

DISPLAY PANEL

MAINS AC

OUTPUT

90-260V,

50/60 Hz

MAX 16A

9

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

S T A N D A R D

D M X 5 1 2

DMX OUT DMX OUT

DMX IN DMX IN

DMX OUT

DMX IN

DMX OUT

8- DMX SIGNAL CONNECTION:

The unit operates using a digital DMX 512 signal.

Connection between the controller and the unit or between units must be carried out

using a two pair screened ø 0.5 mm.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the DMX connector chassis.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

unit to the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

If the display showing the DMX address flashes, then one of the following errors has

occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we

suggest to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

10

8.1 DMX addresses

SCENA LED 80 FC can be controlled with 10 DMX channels (Default).

In order to use the unit in 10 DMX channels mode, set the following addresses on the

mixer:

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

projector 6 A051

8.2 Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more

quickly and you get a faster selection.

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now controlled by the new DMX address.

9- FIRMWARE UPDATING

To update the software version of the SCENA LED 80 FC you need:

- D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008)

- USB-DMX Driver for the D.T.S. RED BOX interface

- “D.T.S. Firmware upgrade utility” program installed on PC

- Latest firmware release available for SCENA LED 80 FC unit

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Send the new software version into the unit by using “D.T.S. Firmware upgrade

Utility” program.

11

Up-Down

MENU

ENTERUp-Down

Up-DownENTER

ENTER

Up-Down

MENU

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

ENTER

Standard mode enabled:

(Default).

Extended mode enabled:

Rainbow effects on

MACRO channel.

10- DISPLAY FUNCTIONS

DISPLAY FUNCTIONS

The SCENA LED 80 FC display panel shows all the available functions.

Using these functions, it is possible to change some of the parameters and add some

functions. Changing the D.T.S. setting can vary the functions of the unit so that it does

not respond to the DMX 512 used to control it. Carefully follow the instructions below

before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired

function.

Software version 5.13

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position (on the ground or

suspended).

DISPLAY STAND-BY

To turn off the display (after 5 seconds)

Or leave it always on.

DMX MODE

To select DMX mode: 10 DMX channels

mode (default), 6 DMX channel mode,

15 DMX channels mode, “WALL” mode,

“M4CH” mode, “RGBA” mode or 1 DMX

channel mode.

MACRO

MACRO Function, enable channel mapping

macro rainbow effects

STD (default)

Suspended

Position

Floor

Position

Display

Off

Display

Always on

Default DMX Mode

10 Channels

1 channel mode

6 DMX channels mode

15 DMX channels mode

“WALL” (6 channels mode)

“M4CH” (5 channels mode)

“RGBA” (4 channels mode)

12

With BOOST active, the LED’S

current is set to Max value.

(30% more gain compared to

BOOST Off)

Default = Disabled

Up-Down

MENU

ENTER

Up-Down

Up-DownENTER

ENTER

Up-Down

Up-DownENTER

ENTER

Up-DownENTER

ENTER

LED

RGBW Min/Max, Smooth,

Compression, Sync and Boost level

values settings

RGBW MINIMUM VALUE

This menu allows to select the

minimum levels for Red, Green,

Blue and White

RGBW MAXIMUM VALUE

This menu allows to select the

maximum levels for Red, Green,

Blue and White

These settings have priority

on Master Dimmer channel

SMOOTH VALUE

This menu allows to select the value

of the delay (in milliseconds) for

Dimmer channel reaction to DMX

or Program variation.

Off = 25 ms Instant response to

DMX variation.

20 = 250 ms Smooth response to

DMX variation.

COMPRESSION

This menu allows to select between

Linear current output or Quadratic

current output for LEDs

Default = Quadratic

SYNC

This menu allows to adjust the PWM

frequency value (Hz) in order to

reduce flickering in the process of

your camera recordings

BOOST DRIVING

This menu allows to increase the

LED’s current from 350mA to

500mA

Linear = Linear

Current output

Quadratic =

Linear light

output

Range: 0-100

Range = Off-20

Default = 4

Range =

610 Hz – 20 KHz

Default = 610 Hz

Boost mode

activated

Boost mode

deactivated

13

Up-DownENTER ENTER

Up-DownENTER

ENTER

MENU Up-Down

ENTER

MENU

Up-Down

Up-DownENTER ENTER

Up-Down

ENTER

Up-Down

ENTER

Up-Down

Up-DownENTER ENTER

AUTOMATIC MODE

Automatic demo game without DMX controller

ChPr

Chase with 16 steps previously created in REC

MODE

Speed and Wait time selectable by user

CUPr

RGBW values selectable by user

Rainbow (rAIn)

Rainbow colours effect.

Speed time selectable by user

CU01-CU16

Color Macros as on DMX channel 9 (MACRO)

WHITE MACROS

16 macros for White color from 2800K to 6500K

DIMMER

Dimmer level selectable by user as on DMX

channel 2 (DIMMER)

Dimmer level is active for all the programs and

macros

SHUTTER

Shutter level selectable by user as on DMX

channel 1 (SHUTTER)

Shutter level is active only for CU01/CU16 and

Wh01/Wh16 macros

ESC

Esc from Automatic Mode Menu

REC MODE

In DMX Recorder Mode,it is possible to

create and store the scenes of the ChPr by

using an external DMX controller.

The unit must be set to 10 channels mode.

14

ENTER

MENU Up-Down

Up-DownENTER

Up-Down

DMX Recorder Mode

For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a

further 3 DMX channels are needed.

So that in RECORDER mode (via DMX) the unit will need 13 channels to be correctly programmed.

The three new DMX channels are:

DMX channel 11 = SCENES channel

From 0-10 = no function (r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016)

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record

the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as

last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been

recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have

decided to save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-255), in

playback mode all 16 scenes will be played through even if not programmed

MENU

Up-Down Up-DownENTER

ENTER

INFRARED MODE

Infrared remote control.

By activating Ir Mode, it will be

possible to navigate trought the unit

functions by using the D.T.S.

infrared remote control

(D.T.S. Code: 0514L008)

Note:

External infrared remote sensor

needed (D.T.S. Code: 03.LA.016)

NOT IMPLEMENTED ON SCENA LED 80 FC

SLAVE MODE

Slave mode for ChPr program.

All slave units will be synchronised

with master unit, running their own

Chpr program.

15

MENU Up-Down

Up-DownENTER

ENTER

WIRELESS DMX

Wireless DMX enabled / disabled.

By activating WDMX MODE, it will be

possible to control SCENA LED 80 FC

via D.T.S. ANTENNA Wireless DMX

Transmitter (cod. 03.E1271).

Active only on SCENA LED 80 FC with

Wireless on board

Wireless

Enabled

Wireless

Disabled

UNLINK = LOG OUT

Logging on SCENA LED 80 FC (WIRELESS DMX must be enabled on SCENA LED 80 FC unit)

To log on the SCENA LED 80 FC in the WIRELESS system simply press and quickly release the function

button on the transmitter.

The transmitter will start flashing rapidly red/green scanning for new free receivers / SCENA LED 80 FC units.

When a SCENA LED 80 FC logs on to the transmitter the LINK green light on transmitter starts to flash

rapidly.

After approximately 10 seconds the transmitter will jump back to normal mode and continue transmitting data.

The SCENA LED 80 FC now try to synchronize to the transmitter.

When synchronized to the transmitter, 2 different modes are possible:

1. Antenna transmitter has detected and transmits a DMX signal, in this mode a solid green light is seen on the

transmitter and solid display is seen on SCENA LED 80 FC.

2. No DMX signal connected, the Antenna transmitter will flash red/green; display blinking on SCENA LED 80

FC.

To log SCENA LED 80 FC off from a transmitter simply select UNLINK function under

WIRELESS DMX MENU and press ENTER.

When SCENA LED 80 FC is logged off, the display is blinking, meaning its available for log in on a new

transmitter.

Logging out a SCENA LED 80 FC

Select UNLINK function under WIRELESS DMX MENU and press ENTER.

When SCENA LED 80 FC is logged off the display is blinking, meaning its available for log in on a new

transmitter.

Logging out all SCENA LED 80 FC units linked to a transmitter

Press and hold the function button of the transmitter for about 3 seconds. When the display is blinking on

SCENA LED 80 FC, it mean that the units are logged out.

Transmitter, Status LED

Flashing red/green, no dmx connected.

Solid green, dmx signal detected and transmitted.

Fast flashing red/green, log in mode (every free SCENA LED 80 FC unit, not logged in to any other transmitter,

will be logged on)

SCENA LED 80 FC Status

Display blinking = not logged on to a transmitter (free).

Solid display = logged on to a transmitter and receiving dmx data.

16

ENTER

Up-DownENTER

Up-Down

MENU

ENTER

MENU Up-Down

Up-DownENTER

ENTER

Up-DownENTER

ENTER

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it

will be possible to select

Dimmer intensity level that will

then ran if DMX signal is

missing or not available.

Usefull for Emergency EXIT

illumination on public areas.

ENTERENTER

Up-Down

MENU

ENTERENTER

Up-Down

MENU

.

DEFAULT SETTING

To restore default settings

TEMPERATURE

Internal unit temperature

visualisation

Internal unit temperature

(° Celsius)

LIFE TIME

This menu shows the total unit life

time and the LED life time

SOFTWARE

Software version

Default = OFF

ENTER

Up-Down

MENU

. .

17

11- DMX PROTOCOL

10 CHANNELS MODE (Default)

1 SHUTTER

2 DIMMER

3 RED

4 GREEN

5 BLUE

6 WHITE

7 WHITE PRE-PROGRAMMED

8 CTC

9 MACRO

10 FUNCTIONS

DMX CHANNEL

1

Parameter: SHUTTER

DMX range

Value

Mid Point

DMX

value

Move Range

(degrees)

Mode

Option

Function

000-009

5

Black-out

010-019

14

Open

020-029

24

Black-out

030-119

Strobe at variable speed from slow

to fast (3,27 s – 30 ms)

120-149

Pulse open at variable speed from

slow to fast (42,6 s – 120 ms)

150-179

Pulse close at variable speed from

slow to fast (42,6 s – 120 ms)

180-204

192

Random Strobe

205-229

218

Full Independent Random Strobe

230-234

Red, Yellow, Cyan and Blue colour

effects at variable speed

235-255

245

Open

DMX CHANNEL

2

Parameter: DIMMER

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

dimmer

DMX CHANNEL

3

Parameter: RED

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

4

Parameter: GREEN

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

18

DMX CHANNEL

5

Parameter: BLUE

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

6

Parameter: WHITE

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

7

Parameter: WHITE PRE-PROGRAMMED

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-055

23

No Function

056-105

80

Full (Red-Green-

Blue at Full)

106-155

130

White DTS

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE RECALL (DMX range value 000-079)

156-205

180

Custom White

Recall

206-255

225

White CTC

(Channel 8 CTC

enabled 256

color temp.

Correction

Macros: 2800°K

– 6500°K)

IF CHANNEL 10 (FUNCTIONS) = CUSTOM WHITE CREATE (DMX range value 080-160)

156-205

180

Custom White

Create (RGB

levels selectable

by DMX)

206-255

225

White CTC

(Channel 8 CTC

enabled 256

color temp.

Correction

Macros: 2800°K

– 6500°K)

DMX CHANNEL

8

Parameter: CTC (Colour Temperature Correction)

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

IF CHANNEL 7 (WHITE PRE-PROGRAMMED) = WHITE CTC (DMX range value 206-255)

000-255

256 colour temp. Correction

Macros: 0=2800°K / 128=4500°K

/ 255=6500°K

IF CHANNEL 7 (WHITE PRE-PROGRAMMED) = NO FUNCTION (DMX range value 000-055)

000-255

NO FUNCTION

19

DMX CHANNEL

9

Parameter: MACRO

IF:

DMX range

Value

Mid Point

DMX value

Move Range

(degrees)

Mode

Option

Function

000-014

No Function

015-029

Macro 1

030-044

Macro 2

045-059

Macro 3

060-074

Macro 4

075-089

Macro 5

090-104

Macro 6

105-119

Macro 7

120-134

Macro 8

135-149

Macro 9

150-164

Macro 10

165-179

Macro 11

180-194

Macro 12

195-209

Macro 13

210-225

Macro 14

226-239

Macro 15

240-255

Macro 16

DMX CHANNEL

9

Parameter: MACRO

IF:

DMX range

Value

Mid Point

DMX value

Move Range

(degrees)

Mode

Option

Function

000-014

No Function

015-022

Macro 1

023-030

Macro 2

031-038

Macro 3

039-046

Macro 4

047-054

Macro 5

055-062

Macro 6

063-070

Macro 7

071-078

Macro 8

079-086

Macro 9

087-094

Macro 10

095-102

Macro 11

103-110

Macro 12

111-118

Macro 13

119-126

Macro 14

127-134

Macro 15

135-142

Macro 16

143-150

Rainbow Speed 1 (1 Sec.)

151-158

Raibow Speed 2 (5 Sec.)

159-166

Rainbow Speed 3 (10 Sec.)

167-174

Rainbow Speed 4 (20 Sec.)

175-182

Rainbow Speed 5 (30 Sec.)

183-190

Rainbow Speed 6 (60 Sec.)

191-198

Rainbow Speed 7 (120 Sec.)

199-206

Rainbow Speed 8 (180 Sec.)

207-214

Random Speed 1 (0,5 Sec.)

215-222

Random Speed 2 (1 Sec.)

223-230

Random Speed 3 (2 Sec.)

231-238

Random Speed 4 (5 Sec.)

239-246

Random Speed 5 (10 Sec.)

247-255

Random Speed 6 (30 Sec.)

PLEASE CHECK PAGE 11

20

DMX CHANNEL

10

Parameter: FUNCTIONS (Recall, Create and Store the Custom white)

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-079

Custom White

Recall (Enable

CH 7 for Custom

white Recall)

080-160

Custom White

Create (Enable

CH 7 for Custom

white Creation)

161-255

Custom White

Store (Store the

Custom White

created)

“WALL” 6 CHANNELS MODE

(For use with DTS Wall mounted DMX controller 0514L007)

Up-DownMENU ENTERUp-Down

ENTER

6 CHANNELS

1 GREEN

2 RED

3 BLUE

4 DIMMER

5 NOT USED

6 SHUTTER

DMX CHANNEL

1

Parameter: GREEN

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

2

Parameter: RED

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

DMX CHANNEL

3

Parameter: BLUE

DMX range

Value

Mid Point DMX

value

Move Range

(degrees)

Mode

Option

Function

000-255

Proportional

colour

La pagina sta caricando ...

DTS SCENA COMPACT LED 50 Manuale utente

Questo manuale è adatto anche per

DTS SCENA COMPACT LED 50 Manuale utente

in altre lingue

Documenti correlati