Mosa TS 250 KD/EL Manuale del proprietario

Categoria
Sistema di saldatura
Tipo
Manuale del proprietario
USE AND MAINTENANCE MANUAL
M A D E I N I T A L Y
TS 250 KD
Codice
Code
Codigo
Kodezahl
120309003
Edizione
Edition
Edición
Ausgabe
03.2014
DESCRIPTION OF THE MACHINE TS 250 D
M
0
REV.0-03/14
The TS 250 engine driven welder ia a unit which ensures the function as:
a) a current source for are welding
b) a current source for the auxiliary generation
Unit meant for industrial and professional use, powered by an endothermic engine; it is composed of various main parts such as:
engine, alternator, electric and electronic controls, the fairing or a protective structure.
The assembling is made on a steel structure, on which are provided elastic support which must damp the vibrations and also
eliminate sounds which would produce noise.
FRAME
VIBRATION
DAMPER
FRONTAL
PANEL
ALTERNATOR
ENGINE
Quality system
M
01
REV.4-03/12
UNI EN ISO 9001 : 2008
10/10/02 M01-GB
MOSA has certied its quality system according
to UNI EN ISO 9001:2008 to ensure a constant,
highquality of its products. This certication covers
thedesign, production and servicing of engine dri-
venwelders and generating sets.
The certifying institute, ICIM, which is a member
ofthe International Certication Network IQNet,
awarded the ofcial approval to MOSA after an-
examination of its operations at the head ofce
andplant in Cusago (MI), Italy.
This certication is not a point of arrival but a
pledgeon the part of the entire company to maintain
a levelof quality of both its products and services
whichwill continue to satisfy the needs of its clients,
aswell as to improve the transparency and thecom-
munications regarding all the company’s activesin
accordance with the ofcial procedures and inhar-
mony with the MOSA Manual of Quality.
The advantages for MOSA clients are:
·Constant quality of products and services at thehigh
level which the client expects;
· Continuous efforts to improve the products andtheir
performance at competitive conditions;
· Competent support in the solution of problems;
· Information and training in the correct applicatio-
nand use of the products to assure the security
ofthe operator and protect the environment;
· Regular inspections by ICIM to conrm that the-
requirements of the company’s quality systemand
ISO 9001 are being respected.
All these advantages are guaranteed by the CER-
TIFICATE OF QUALITY SYSTEM No.0192 issued
by ICIM S.p.A. - Milano (Italy ) - www.icim.it
INDEX
M
1
REV.2-03/14
11/01/01 M1-GB
M 01 QUALITY SYSTEM
M 1.01 COPYRIGHT
M 1.1 NOTES
M 1.4 CE MARK
M 1.4.1 DECLARATION OF CONFORMITY
M 1.5 TECHNICAL DATA
M 1.6 TECHNICAL DATA ENGINE DRIVEN WELDER
M 2-2.1 SYMBOLS AND SAFETY PRECAUTIONS
M 2.5... INSTALLATION AND ADVICE BEFORE USE
M 2.6 INSTALLATIONS AND ADVICE
M 2.7 INSTALLATION
M 2.7.1 DIMENSIONS
M 3 PACKING
M 4... TRANSPORT AND DISPLACEMENTS
M 6... ASSEMBLY: CT........
M 20 SETTING-UP THE UNIT (DIESEL ENGINE)
M 21 ENGINE STARTING AND USE (DIESEL ENGINE)
M 22 STOPPING THE ENGINE (DIESEL ENGINE)
M 25 SETTING-UP THE UNIT (GASOLINE ENGINE)
M 26 STARTING THE ENGINE (GASOLINE ENGINE)
M 27 STOPPING THE ENGINE (GASOLINE ENGINE)
M 30 CONTROLS LEGEND
M 31 CONTROLS
M 34 USE AS A WELDER
M 35 USE AS AN ENGINE STARTER
M 36 USE AS A BATTERY CHARGE
M 37... USE AS A GENERATOR
M 38... USE OF THE REMOTE CONTROL
M 39... USE OF THE ENGINE PROTECTION
M 40... TROUBLE SHOOTING
M 43... MAINTENANCE
M 45 STORAGE
M 46 CAST OFF
M 55 RECOMMENDED ELECTRODES
M 60 ELECTRICAL SYSTEM LEGENDE
M 61... ELECTRICAL SYSTEM
Copyright
M
1.01
REV.0-10/02
All rights are reserved to said Company.
It is a property logo of MOSA division of B.C.S. S.p.A.
All other possible logos contained in the documen-
tation are registered by the respective owners.
+ The reproduction and total or partial use, in any
form and/or with any means, of the documen-
tation is allowed to nobody without a written
permission by MOSA division of B.C.S. S.p.A.
To this aim is reminded the protection of the author’s
right and the rights connected to the creation and
design for communication, as provided by the laws
in force in the matter.
In no case MOSA division of B.C.S. S.p.A. will be
held responsible for any damaga, direct or indirect,
in relation with the use of the given information.
MOSA division of B.C.S. S.p.A. does not take any
responsibility about the shown information on rms
or individuals, but keeps the right to refuse services
or information publication which it judges discutible,
unright or illegal.
10/10/02 M1-01-GB
This use and maintenance manual is an important
part of the machines in question.
The assistance and maintenance personel must
keep said manual at disposal, as well as that
for the engine and alternator (if the machine is
synchronous) and all other documentation about
the machine.
We advise you to pay attention to the pages
concerning the security (see page M1.1).
ATTENTION
!
INFORMATION
Dear Customer,
We wish to thank you for having bought a high quality set.
Our sections for Technical Service and Spare Parts will
work at best to help you if it were necessary.
To this purpose we advise you, for all control and over-
haul operations, to turn to the nearest authorized Service
Centre, where you will obtain a prompt and specialized
intervention.
+ In case you do not prot on these Services and some
arts are replaced, please ask and be sure that are
used exclusively original parts; this to guarantee that
the performances and the initial safety prescribed by
the norms in force are re-established.
+The use of non original spare parts will cancel
immediately any guarantee and Technical Service
obligation.
NOTES ABOUT THE MANUAL
Before actioning the machine please read this manual
attentively. Follow the instructions contained in it, in this
way you will avoid inconveniences due to negligence,
mistakes or incorrect maintenance. The manual is for
qualied personnel, who knows the rules: about safety
and health, installation and use of sets movable as well
as xed.
You must remember that, in case you have difculties
for use or installation or others, our Technical Service is
always at your disposal for explanations or interventions.
The manual for Use Maintenance and Spare Parts is an
integrant part of the product. It must be kept with care
during all the life of the product.
In case the machine and/or the set should be yielded to
another user, this manual must also given to him.
Do not damage it, do not take parts away, do not tear
pages and keep it in places protected from dampness
and heat.
You must take into account that some gures contained in
it want only to identify the described parts and therefore
might not correspond to the machine in your possession.
INFORMATION OF GENERAL TYPE
In the envelope given together with the machine and/or
set you will nd: the manual for Use Maintenance and
Spare Parts, the manual for use of the engine and the
tools (if included in the equipment), the guarantee (in the
countries where it is prescribed by law).
Our products have been designed for the use of gene-
ration for welding, electric and hydraulic system; ANY
OTHER DIFFERENT USE NOT INCLUDED IN THE
ONE INDICATED, relieves the manufacturer from the
risks which could happen or, anyway, from that which
was agreed when selling the machine. The manufacturer
excludes any responsibility for damages to the machine,
to the things or to persons in this case.
Our products are made in conformity with the safety
norms in force, for which it is advisable to use all these
devices or information so that the use does not bring
damage to persons or things.
While working it is advisable to keep to the personal safety
norms in force in the countries to which the product is
destined (clothing, work tools, etc.).
Do not modify for any motive parts of the machine (faste-
nings, holes, electric or mechanical devices, others..) if
not duly authorized in writing: the responsibility coming
from any potential intervention will fall on the executioner
as in fact he becomes maker of the machine.
Notes
M
1-1
REV.0-10/02
+ Notice: this manual does not engage the manufacturer,
who keeps the faculty, apart the essential characte-
ristics of the model here described and illustrated,
to bring betterments and modications to parts and
accessories, without putting this manual uptodate
immediately.
10/10/02 M 1-1 GB_NEUTRO
CE MARK
M
1.4
REV.7-02/14
10/10/02 M1-4 GB
Any of our product is labelled with CE marking attesting its conformity to appliable directives and
also the fulllment of safety requirements of the product itself; the list of these directives is part
of the declaration of conformity included in any machine standard equipment.
Here below the adopted symbol:
CE marking is clearly readable and unerasable and it can be either part of the data-plate.
Furthermore, on each model it is shown the noise level value; the symbol used is the following:
The indication is shown in a clear, readable and indeleble way on a sticker.
TEMP.
°CRPM
n
IP
kW
ALTIT.
Kg
m
G
P.F.
Hz
V(V)
I(A)
KVA
TYPE
I.CL.
SERIAL
Made in UE-ITALY
TYPE/N°
VOLTAGE(V)
POWER(W)
LTP POWER IN ACCORDANCE WITH ISO 8528
Pmax
04/06/10 M1.4.1
Dichiarazione conformità
Declaration of conformity
Déclaration de conformité
M
1.4.1
REV.2-10/13
I
GB
F
Konformitätserklärung
Declaración de conformidad
Declaração de conformidade
MM 083.1
BCS S.p.A.
Sede legale:
Via Marradi 1
20123 Milano - Italia
Stabilimento di Cusago, 20090 (Mi) - Italia
V.le Europa 59
Tel.: +39 02 903521
Fax: +39 02 90390466
DICHIARAZIONE DI CONFORMITA'
Déclaration de Conformité – Declaration of Conformity – Konformitätserklärung
Conformiteitsverklaring – Declaración de Conformidad
BCS S.p.A. dichiara sotto la propria responsabiliche la macchina:
BCS S.p.A. déclare, sous sa propre responsabilité, que la machine:
BCS S.p.A. declares, under its own responsibility, that the machine:
BCS S.p.A. erklärt, daß die Aggregate:
BCS S.p.A. verklaard, onder haar eigen verantwoordelijkheid, dat de machine:
BCS S.p.A. declara bajo su responsabilidad que la máquina:
GRUPPO ELETTROGENO DI SALDATURA / WELDING GENERATOR
GRUPPO ELETTROGENO / POWER GENERATOR
TORRE FARO / LIGHTING TOWER
Marchio / Brand :
Modello / Model :
Matricola / Serial number :
è conforme con quanto previsto dalle Direttive Comunitarie e relative modifiche:
est en conformité avec ce qui est prévu par les Directives Communautaires et relatives modifications:
conforms with the Community Directives and related modifications:
mit den Vorschriften der Gemeinschaft und deren Ergänzungen übereinstimmt:
in overeenkomst is met de inhoud van gemeenschapsrichtlijnemen gerelateerde modificaties:
comple con los requisítos de la Directiva Comunitaria y sus anexos:
2006/42/CE - 2006/95/CE - 2004/108/CE
Nome e indirizzo della persona autorizzata a costituire il fascicolo tecnico :
Nom et adresse de la personne autorisée à composer le Dossier Technique :
Person authorized to compile the technical file and address :
Name und Adresse der zur Ausfüllung der technischen Akten ermächtigten Person :
Persoon bevoegd om het technische document , en bedrijf gegevens in te vullen
Nombre y dirección de la persona autorizada a componer el expediente técnico :
ing. Benso Marelli - Consigliere Delegato / Managing Director ; V.le Europa 59, 20090 Cusago (MI) – Italy
_______________
Cusago, Ing. Benso Marelli
Consigliere Delegato
Managing Director
17/03/14 12030-GB
Technical data
TS 250 D
M
1.5
REV.0-03/14
Technical data TS 250 D
ALTERNATOR Self-excited,self-regulated,brushless
Type three-phase,asynchronous
Insulating class H
GENERATOR
Three-phase generation 6.5kVA/400V/9.4A
Single-phase generation 4.5kVA/230V/19.5A
Single-phase generation 2kVA/48V/41.6A
Frequency 50Hz
ENGINE
Mark / Model KohlerKD477/2
Type / Cooling system Diesel4-Stroke/air
Cylinders / Displacement 2/954cm
3
Netoutput 14.9kW(20.3HP)
Speed 3000rpm
Fuel consumption (Welding 60%) 1.7l/h
Engine oil capacity 3l
Starter electric
GENERAL SPECIFICATIONS
Tank capacity 9l
Running time (Welding 60%) 5.3h
Protection IP23
*Dimensions Lxwxh (mm) * 1050x530x630
*Weight 200Kg
**Acoustic power LwA (pressure LpA) 103dB(A)(78dB(A)@7m)
* Dimensions and weight are inclusive of all parts without wheels and towbar ** For xed installation only.
POWER
Declared power according to ISO 3046-1 (temperature 25°C, 30% relative hummidity, altitude 100 m above sea level).
It’s admitted overload of 10% each hour every 12 h.
In an approximative way one reduces: of 1% every 100 m altitude and of 2.5% for every 5°C above 25°C.
ACOUSTIC POWER LEVEL
ATTENTION: The concrete risk due to the machine depends on the conditions in which it is used. Therefore, it is up to the end-
user and under his direct responsibility to make a correct evaluation of the same risk and to adopt specic precautions (for
instance, adopting a I.P.D. -Individual Protection Device)
Acoustic Noise Level (LWA) - Measure Unit dB(A): it stands for acoustic noise released in a certain delay of time. This is not
submitted to the distance of measurement.
Acoustic Pressure (Lp) - Measure Unit dB(A): it measures the pressure originated by sound waves emission. Its value changes
in proportion to the distance of measurement.
The here below table shows examples of acoustic pressure (Lp) at different distances from a machine with Acoustic Noise Level
(LWA) of 95 dB(A)
Lp a 1 meter = 95 dB(A) - 8 dB(A) = 87 dB(A) Lp a 7 meters = 95 dB(A) - 25 dB(A) = 70 dB(A)
Lp a 4 meters = 95 dB(A) - 20 dB(A) = 75 dB(A) Lp a 10 meters = 95 dB(A) - 28 dB(A) = 67 dB(A)
PLEASE NOTE: the symbol when with acoustic noise values, indicates that the device respects noise emission limits
according to 2000/14/CE directive.
2000 / 14 /CE
17/03/14 12030-GB
Technical data
TS 250 D
M
1.6
REV.0-03/14
WELDING
Max DC welding current 200A/60%-250A/35%
Welding current electronic regulation 20-250A
Open circuit voltage 70V
Welding voltage 20-30V
Welding current regu-
lator position approx.
current values
25% 50% 75% 100%
20 70 130 190 250
6.5 kVA
4 kVA2.5 kVA0
AUXILIARY POWER
0
80 A130 A>170 A
WELDING CURRENT
EXIT CHARACTERISTICS
0%
A
SIMULTANEOUS UTILIZATION FACTORS
In case Welding and Generation can be used simultaneously, however, the engine cannot be overloaded.
The table below gives the maximum limits to be respected.
SYMBOLS AND SAFETY PRECAUTIONS
M
2
REV.0-11/99
SYMBOLS IN THIS MANUAL
- The symbols used in this manual are designed to call
your attention to important aspects of the operation of
the machine as well as potential hazards and dangers
for persons and things.
IMPORTANT ADVICE
- Advice to the User about the safety:
+ N.B.: The information contained in the manual can be
changed without notice. Potential damages caused
in relation to the use of these instructions will not be
considered because these are only indicative.
Remember that the non observance of the indications
reported by us might cause damage to persons or
things. It is understood, that local dispositions and/or
laws must be respected.
WARNING
Situations of danger - no harm to persons
or things
Do not use without protective devices provided
Removing or disabling protective devices on the
machine is prohibited.
Do not use the machine if it is not in good technical
condition
The machine must be in good working order before
being used. Defects, especially those which regard
the safety of the machine, must be repaired before
using the machine.
SAFETY PRECAUTIONS
This heading warns of an immediate danger for persons
as well for things. Not following the advice can result in
serious injury or death.
This heading warns of situations which could result in
injury for persons or damage to things.
To this advice can appear a danger for persons as well
as for things, for which can appear situations bringing
material damage to things.
These headings refer to information which will assis you
in the correct use of the machine and/or accessories.
!
26/11/99 M2GB
WARNING
DANGEROUS
CAUTION
IMPORTANT
NOTE
ATTENTION
!
!
!
!
!
!
SYMBOLS AND SAFETY PRECAUTIONS
M
2-1
REV.2-06/10
SYMBOLS
STOP - Read absolutely and be duly attentive
Read and pay due attention
GENERAL ADVICE - If the advice is not
respected damage can happen to persons or
things.
HIGH VOLTAGE - Attention High Voltage.
There can be parts in voltage, dangerous
to touch. The non observance of the advice
implies life danger.
FIRE - Danger of ame or re. If the advice is
not respected res can happen.
HEAT - Hot surfaces. If the advice is not
respected burns or damage to things can be
caused.
EXPLOSION - Explosive material or danger
of explosion. in general. If the advice is not
respected there can be explosions.
WATER - Danger of shortcircuit. If the advice
is not respected res or damage to persons
can be caused.
SMOKING - The cigarette can cause re or
explosion. If the advice is not respected res
or explosions can be caused.
ACIDS - Danger of corrosion. If the advice is
not respected the acids can cause corrosions
with damage to persons or things.
WRENCH - Use of the tools. If the advice is
not respected damage can be caused to things
and even to persons.
PRESSION - Danger of burns caused by the
expulsion of hot liquids under pressure.
PROHIBITIONS No harm for persons
Use only with safety clothing -
It is compulsory to use the personal
protection means given in equip-
ment.
Use only with safety clothing -
It is compulsory to use the personal protection
means given in equipment.
Use only with safety protections -
It is a must to use protection means suitable for
the different welding works.
Use with only safety material -
It is prohibited to use water to quench res on
the electric machines.
Use only with non inserted voltage -
It is prohibited to make interventions before
having disinserted the voltage.
No smoking -
It is prohibited to smoke while lling the tank
with fuel.
No welding -
It is forbidden to weld in rooms containing
explosive gases.
ADVICE No harm for persons and things
Use only with safety tools, adapted to the specic
use -
It is advisable to use tools adapted to the various
maintenance works.
Use only with safety protections, specically suitable
It is advisable to use protections suitable for the
different welding works.
Use only with safety protections -
It is advisable to use protections suitable for
the different daily checking works.
Use only with safety protections -
It is advisable to use all protections while
shifting the machine.
Use only with safety protections -
It is advisable to use protections suitable for
the different daily checking works.and/or of
maintenance.
!
26/11/99 M2-1GB
ACCES FORBIDDEN to non authorized peaple.
INSTALLATION AND ADVICE BEFORE USE
M
2-5
REV.0-06/00
The installation and the general advice concerning the operations, are nalized to the correct use of the ma-
chine, in the place where it is used as generator group and/or welder.
!
+ FIRSTAID. In case the operator shold be sprayed by accident, from corrosive liquids a/o hot toxic gas
or whatever event which may cause serious injuries or death, predispose the rst aid in accordance
with the ruling labour accident standards or of local instructions.
+ FIREPREVENTION. In case the working zone,for whatsoever cause goes on re with ames liable to
cause severe wounds or death, follow the rst aid as described by the ruling norms or local ones.
10/06/00 M2-5I
ENGINE
Stop engine when fueling
CHECKINGBOARD
Do not touch electric devices
if you are barefoot or with wet
clothes.
Do not smoke, avoid ames, sparks or electric tools when fueling.
Unscrew the cap slowly to let out the fuel vapours.
Always keep off leaning sur-
faces during work operations.
Slowly unscrew the cooling liquid tap if the liquid must be topped up.
The vapor and the heated cooling liquid under pressure can burn face, eyes, skin.
Static electricity can demage
the parts on the circuit.
Do not ll tank completely.
Wipe up spilled fuel before starting engine.
An electric shock can kill
Shut off fuel of tank when moving machine (where it is assembled).
Avoid spilling fuel on hot engine.
Sparks may cause the explosion of battery vapours
Skin contact Wash with water and soap
Eyes contact Irrigate with plenty of water, if the irritation persists contact a specialist
Ingestion Do not induce vomit as to avoid the intake of vomit into the lungs, send for a doctor
Suction of liquids from
lungs
If you suppose that vomit has entered the lungs (as in case of spontaneous vomit) take the subject to the
hospital with the utmost urgency
Inhalation In case of exposure to high concentration of vapours take immediately to a non polluted zone the person involved
EXTINCTIONMEANS
Appropriated Carbonate anhydride (or carbon dioxyde) powder, foam, nebulized water
Not to be used Avoid the use of water jets
Other indications Cover eventual shedding not on re with foam or sand, use water jets to cool off the surfaces close to the re
Particular protection Wear an autorespiratory mask when heavy smoke is present
Useful warnings Avoid, by appropriate means to have oil sprays over metallic hot surfaces or over electric contacts
(switches,plugs,etc.). In case of oil sprinkling from pressure circuits, keep in mind that the inamability
point is very low.
WARNING
THE MACHINE MUST NOT BE USED IN AREAS WITH EX-
PLOSIVE ATMOSPHERE
WARNING CAUTION
DANGEROUS
!
!
!
!
PRECAUTION (ENGINE DRIVEN WELDER)
M
2-5-1
REV.0-03/00
INSTALLATION AND ADVICE BEFORE USE
The operator of the welder is responsible for the security of the people who work with the welder and for those in
the vicinity.
The security measures must satisfy the rules and regulations for engine driven welders.
The information given below is in addition to the local security norms.
Estimate possible electromagnetic problems in the work area taking into account the following indications.
1. Telephonic wirings and/or of communication, check wirings and so on, in the immediate vicinity.
2. Radio and television receptors and transmettors.
3. Computer and other checking devices.
4. Critical devices for safety and/or for industrial checks.
5. Peapol who, for instance, use pace-maker, hearing-aid for deaf or something and else.
6. Devices used for rating and measuring.
7. The immunity of other devices in the operation area of the welder. Make sure that other used devices are
compatible. If it is the case, provide other additional measures of protection.
8. The daily duration of the welding time.
Make sure that the area is safe before starting any welding operation.
àDo not touch any bare wires, leads or contacts as they may be live and there is danger of electric shock
which can cause death or serious burns. The electrode and welding cables, etc. are live when the unit
is operating.
àDo not touch any electrical parts or the electrode while standing in water or with wet hands, feet or clothes.
àInsulate yourself from the work surface while welding. Use carpets or other insulating materials to avoid
physical contact with the work surface and the oor.
àAlways wear dry, insulating glovers, without holes, and body protection.
àDo not wind cables around the body.
àUse ear protections if the noise level is high.
àKeep amable material away from the welding area.
àDo not weld on containers which contain amable material.
àDo not weld near refuelling areas.
àDo not weld on easily amable surfaces.
àDo not use the welder to defrost (thaw) pipes.
àRemove the electrode from the electrode holder, when not welding.
àAvoid inhaling fumes by providing a ventilation system or, if not possible, use an approved air breather.
àDo not work in closed areas where there is no fresh air ow.
àProtect face and eyes (protective mask with suitable dark lens and side screens), ears and body (non-
amable protective clothers).
30/03/00 M2-5GB
WARNING
!
INSTALLATION AND ADVICE
M
2.6
REV.1-06/07
INSTALLATION AND ADVICE BEFORE USE
GASOLINE ENGINES
+
Use in open space, air swept or vent exhaust gases,
which contain the deathly carbone oxyde, far from
the work area.
DIESEL ENGINES
+ Use in open space, air swept or vent exhaust gases
far from the work area.
POSITION
Place the machine on a level surface at a distance of at
least 1,5 m from buildings or other plants.
Check that the air gets changed completely and the hot
air sent out does not come back inside the set so as to
cause a dangerous increase of the temperature.
+ Make sure that the machine does not move during the
work: block it possibly with tools and/or devices made
to this purpose.
Maximum leaning of the machine (in case of dislevel)
10°
10°
= 20° max
10°
10°
= 20° max
26/11/99 M2-6GB
1,5 m
1,5 m
1,5 m
GAS DI SCARICO
EXHAUST OUTPUT
MOVES OF THE MACHINE
+ At any move check that the engine is off, that there are
no connections with cables which impede the moves.
PLACE OF THE MACHINE
ATTENTION
For a safer use from the operator DO NOT
t the machine in locations with high risk
of ood.
Please do not use the machine in weather
conditions which are beyond IP protection
shown both in the data plate and on page
named "technical data" in this same manual.
!
Dimensioni
Dimensions
Dimensions
17/03/14 12030-I
D
E
NL
TS 250 KD
M
2.7.1
REV.0-03/14
Abmessungen
Dimensiones
NOTE
UNPACKING
M
3
REV.1-02/04
!
+ Be sure that the lifting devices are: correctly mounted,
adequate for the weight of the machine with it’s pack-
aging, and conforms to local rules and regulations.
When receiving the goods make sure that the product
has not suffered damage during the transport, that
there has not been rough handling or taking away of
parts contained inside the packing or in the set.
In case you nd damages, rough handling or absence
of parts (envelopes, manuals, etc.), we advise you to
inform immediately our Technical Service.
For eliminating the packing materials, the User
must keep to the norms in force in his country.
1) Take the machine (C) out of the shipment packing.
Take out of the envelope (A) the user’s manual (B).
2) Read: the user’s manual (B), the plates xed on the
machine, the data plate.
30/03/00 M3GB
2
B
A
1
C
TRANSPORT AND DISPLACEMENTS COVERED UNITS
M
4-1
REV.2-09/11
NOTE
!
Transportation must always take place with the engine off, electrical cables and starting battery disconnected and
fuel tank empty.
Be sure that the lifting devices are: correctly mounted, adequate for the weight of the machine with it’s packaging,
and conform to local rules and regulations.
Only authorized persons involved in the transport of the machine should be in the area of movement.
DO NOT LOAD OTHER PARTS WHICH CAN MODIFY WEIGHT AND BARICENTER POSITION.
IT IS STRICTLY FORBIDDEN TO DRAG THE MACHINE MANUALLY OR TOW IT BY ANY VEHICLE (model with
no CTM accessory).
If you did not keep to the instructions, you could damage the structure of the machine.
15/01/01 M4GB
Weight max. per person: 35 kg
Total max. weight; 140 kg
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46

Mosa TS 250 KD/EL Manuale del proprietario

Categoria
Sistema di saldatura
Tipo
Manuale del proprietario

in altre lingue