Mosa Magic Weld 200 Manuale del proprietario

Marca: Mosa

Modello: Magic Weld 200

Categoria: Sistema di saldatura

Tipo: Manuale del proprietario

MADE IN ITALY

Codice

Code

Codigo

Kodezahl

Código

Код

Edizione

Edition

Édition

Edición

Ausgabe

Edição

Издание

C0DN60009003

• Motosaldatrice

• Engine Driven Welder

• Motosoudeuse

• Motosoldadoras

• Schweißaggregat

• Motosoldadora

• По Вышкам

12.2019

COMPACT WELDERS

MAGIC WELD 200 (STAGE V)

USE AND MAINTENANCE MANUAL

TRANSLATION OF THE ORIGINAL INSTRUCTIONS – ENGLISH

language

26/11/08 C0DN6000_EN

ENGLISH

REV.0-12/19

INDEX

0. GENERAL INFORMATION

M1.1

INTRODUTION

..................................................................................................................PAG. 4

M1.4.2

CE MARK

...........................................................................................................................PAG. 5

SYMBOLS AND SAFETY PRECAUTIONS

.............................................................................PAG. 6

M2.1

WARNINGS

....................................................................................................................... PAG. 7

M2.5...

SAFETY RULES (ENGINE DRIVEN WELDERS)

.......................................................................PAG. 8

1. GENERAL INFORMATION OF THE MACHINE

DESCRIPTION OF THE MACHINE

........................................................................................PAG. 12

RECORDING DATA

..............................................................................................................PAG. 13

2. DISPLACEMENTS AND TRANSPORT

MACHINE UNPACKING AND TRANSPORT

............................................................................PAG. 14

3. INSTALLATION AND USE

M2.7

INSTALLATION AND DIMENSIONS

......................................................................................PAG. 15

M2.6

INSTALLATION AND ADVICE

...............................................................................................PAG. 16

M25

SET-UP FOR OPERATION ENGINE

....................................................................................... PAG. 17

M26

STARTING AND STOPPING .................................................................................................

PAG. 18

M31

CONTROLS

........................................................................................................................PAG. 19

M34...

USE AS A WELDER

.............................................................................................................PAG. 20

M34.2

CHECKING AND ADJUSTING THE MAXIMUM WELDING CURRENT ........................................

PAG. 22

M37

USE AS A GENERATOR

....................................................................................................... PAG. 23

4. USING INSTRUMENTS

M55

RECOMMENDED ELECTRODES

..........................................................................................PAG. 24

5. MAINTENANCE

M40.2...

TROUBLE SHOOTING

.........................................................................................................PAG. 25

M43

MAINTENANCE

..................................................................................................................PAG. 27

M45

STORAGE - CUST OFF

.......................................................................................................PAG. 28

6. TECHNICAL INFORMATIONS

M1.5

TECHNICAL DATA

..............................................................................................................PAG. 29

M60

ELECTRICAL SYSTEM LEGENDE

.........................................................................................PAG. 30

M61

ELECTRICAL SYSTEM

........................................................................................................PAG. 31

10/10/02 M1-1_EN

ENGLISH

REV.0-10/02

1.1

INTRODUCTION

Dear Customer,

We wish to thank you for having bought a high quality set.

Our sections for Technical Service and Spare Parts will work at

best to help you if it were necessary.

To this purpose we advise you, for all control and overhaul

operations, to turn to the nearest authorized Service Centre,

where you will obtain a prompt and specialized intervention.

+ In case you do not prot on these Services and some arts

are replaced, please ask and be sure that are used exclusi-

vely original parts; this to guarantee that the performances

and the initial safety prescribed by the norms in force are

re-established.

+The use of non original spare parts will cancel immediately

any guarantee and Technical Service obligation.

NOTES ABOUT THE MANUAL

Before actioning the machine please read this manual atten-

tively. Follow the instructions contained in it, in this way you will

avoid inconveniences due to negligence, mistakes or incorrect

maintenance. The manual is for qualied personnel, who knows

the rules: about safety and health, installation and use of sets

movable as well as xed.

You must remember that, in case you have difculties for use

or installation or others, our Technical Service is always at your

disposal for explanations or interventions.

The manual for Use Maintenance and Spare Parts is an inte-

grant part of the product. It must be kept with care during all

the life of the product.

In case the machine and/or the set should be yielded to another

user, this manual must also given to him.

Do not damage it, do not take parts away, do not tear pages and

keep it in places protected from dampness and heat.

You must take into account that some gures contained in it

want only to identify the described parts and therefore might

not correspond to the machine in your possession.

INFORMATION OF GENERAL TYPE

In the envelope given together with the machine and/or set you

will nd: the manual for Use Maintenance and Spare Parts,

the manual for use of the engine and the tools (if included in

the equipment), the guarantee (in the countries where it is

prescribed by law).

+ NOTICE: the manufacturer, who keeps the faculty, apart

the essential characteristics of the model here described

and illustrated, to bring betterments and modications to

parts and accessories, without putting this manual uptodate

immediately.

The Manufacturer shall not be liable for ANY USE OF THE PRO-

DUCT OTHER THAN THAT PRECISELY SPECIFIED IN THIS

MANUAL and is thus not liable for any risks which may occur as

a result of IMPROPER USE. The Company does not assume

any liability for any damage to persons, animals or property.

Our products are made in conformity with the safety norms in

force, for which it is advisable to use all these devices or informa-

tion so that the use does not bring damage to persons or things.

While working it is advisable to keep to the personal safety

norms in force in the countries to which the product is destined

(clothing, work tools, etc.).

Do not modify for any motive parts of the machine (fastenings,

holes, electric or mechanical devices, others..) if not duly au-

thorized in writing: the responsibility coming from any potential

intervention will fall on the executioner as in fact he becomes

maker of the machine.

10/10/02 M1-4_EN

ENGLISH

12a

12b 12c

13a

13b 13c

13a

13b 13c

14a

14b

14c

14a

14b

14c

Any of our product is labelled with CE marking attesting its conformity to appliable directives and also the fulllment of safety

requirements of the product itself; the list of these directives is part of the declaration of conformity included in any machine

standard equipment.

Here below the adopted symbol:

CE marking is clearly readable and unerasable and it can be either part of the data-plate.

REV.7-02/18

1.4.2

CE MARKING

ENGINE DRIVEN WELDER

Furthermore, on each model it is shown the noise level value; the symbol used is the following:

The indication is shown in a clear, readable and indeleble way on a sticker.

1. Manufacturer name or brand

2. Year of production

3. Engine Driven Welder model

4. Serial number | registration number

5. Reference to the standard conr-

ming that the Engine Driven Welder

complies with its requirements

6. Welding process symbol

7. Symbol for Engine Driven Welders

which can be used an environment

with increased risk of electric shock.

8. Welding current symbol

9. OCV value (Rated no-load voltage)

or adjustment range between mini-

mum and maximum value

10. Reduced rated no-load voltage in

case of a voltage reducing device

(VRD)

11. Maximum and minimum welding

current values and relative voltage

value

12. Duty cycle symbol

12a. Duty cycle values

12b. Duty cycle values

12c. Duty cycle values

13. Rated welding current symbol

13a. Rated welding current values

13b. Rated welding current values

13c. Rated welding current values

14. Conventional load voltage symbol

14a. Welding voltage values

14b. Welding voltage values

14c. Welding voltage values

15. Auxiliary power supply symbol

16. Rated frequency

17. Power factor Cosϕ

18. Insulation class

19. Rated power (kVA/kW)

20. Rated voltage (V)

21. Rated current (A)

22. Rated power (kVA/kW)

23. Rated voltage (V)

24. Rated current (A)

25. Rated power (kVA/kW)

26. Rated voltage (V)

27. Rated current (A)

28. Engine symbol

29. Rated speed

30. Rated no-load speed

31. Rated idle speed

32. Engine maximum power

33. IP degree protection

34. Dry weight (kg)

13/11/14 M2_EN

ENGLISH

REV.2-06/10

SYMBOLS AND SAFETY PRECAUTIONS

SYMBOLS IN THIS MANUAL

- The symbols used in this manual are designed to call your

attention to important aspects of the operation of the machine

as well as potential hazards and dangers for persons and

things.

Moreover, this symbolism intends to draw your attention

with the aim to give you indications for a correct use and,

as a result, to obtain a good operation of the machine or

equipment used.

SAFETY PRECAUTIONS

WARNING

This heading warns of situations which could result in injury

for persons or damage to things.

DANGEROUS

This heading warns of an immediate danger for persons as

well for things. Not following the advice can result in serious

injury or death.

CAUTION

To this advice can appear a danger for persons as well as

for things, for which can appear situations bringing material

damage to things.

IMPORTANT

NOTE

ATTENTION

These headings refer to information which will assis you in

the correct use of the machine and/or accessories.

SIMBOLS

STOP - Read absolutely and be duly attentive

Read and pay due attention

DANGER

GENERAL ADVICE - If the advice is not respec-

ted damage can happen to persons or things.

HIGH VOLTAGE - Attention High Voltage.There

can be parts in voltage, dangerous to touch. The

non observance of the advice implies life danger.

FIRE - Danger of ame or re. If the advice is not

respected res can happen.

HEAT - Hot surfaces. If the advice is not respected

burns or damage to things can be caused.

EXPLOSION - Explosive material or danger of

explosion. in general. If the advice is not respected

there can be explosions.

ACIDS - Danger of corrosion. If the advice is not

respected the acids can cause corrosions with

damage to persons or things.

PRESSION - Danger of burns caused by the

expulsion of hot liquids under pressure.

PROHIBITIONS

It is prohibited to smoke while lling the tank with fuel.

The cigarette can cause re or explosion. If the

advice is not respected res or explosions can

be caused.

It is prohibited to use water to quench res on the electric

machine

If the advice is not respected res or damage to

persons can be caused.

Use only with non inserted voltage -

It is prohibited to make interventions before having

disinserted the voltage.

ACCES FORBIDDEN to non authorized peaple.

ADVICE

Use only with safety clothing -

It is compulsory to use the personal

protection means given in equipment.

WRENCH - Use of the tools. If the advice is not

respected damage can be caused to things and

even to persons.

13/11/14 M2_EN

ENGLISH

+ FIRST AID. In case the operator shold be sprayed by accident, from corrosive liquids a/o hot toxic gas or whate-

ver event which may cause serious injuries or death, predispose the rst aid in accordance with the ruling labour

accident standards or of local instructions.

+ FIRE PREVENTION. In case the working zone,for whatsoever cause goes on re with ames liable to cause severe

wounds or death, follow the rst aid as described by the ruling norms or local ones.

Skin contact Wash with water and soap

Eyes contact Irrigate with plenty of water, if the irritation persists contact a specialist

Ingestion Do not induce vomit as to avoid the intake of vomit into the lungs, send for a doctor

Suction of liquids from

lungs

If you suppose that vomit has entered the lungs (as in case of spontaneous vomit) take the subject to the hospital with the

utmost urgency

Inhalation In case of exposure to high concentration of vapours take immediately to a non polluted zone the person involved

EXTINCTION MEANS

Appropriated Carbonate anhydride (or carbon dioxyde) powder, foam, nebulized water

Not to be used Avoid the use of water jets

Other indications Cover eventual shedding not on re with foam or sand, use water jets to cool off the surfaces close to the re

Particular protection Wear an autorespiratory mask when heavy smoke is present

Useful warnings Avoid, by appropriate means to have oil sprays over metallic hot surfaces or over electric contacts (switches,plugs,etc.).

In case of oil sprinkling from pressure circuits, keep in mind that the inamability point is very low.

REV.2-06/10

2.1

WARNINGS

13/11/14 M2-5 (TS)_EN

ENGLISH

REV.0-01/18

2.5

SAFETY RULES

ENGINE DRIVEN WELDERS

GENERAL SAFETY INSTRUCTIONS

+ NOTE: the information contained in this manual are

subject to change without notice.

The instructions in this manual are intended as indicative only.

It is the responsibility of the owner/operator to evaluate risks

and potential damages in relation to the use of the product in

the specic conditions of application. Remember that the non

observance of the indications of this manual may result in da-

mage to people or things.

In all cases, however, it is understood that the use shall be in

compliance with the applicable laws/regulations.

• Before operating the machine, read carefully the safety in-

structions contained in this manual and other manuals sup-

plied (engine, alternator, etc.).

• All operations, handling, installation, use, maintenance, re-

pair should be carried out by authorized and qualied per-

sonnel.

• When operating, wear personal protective equipment (PPE):

footwear, gloves, helmet, etc..

• The owner is responsible for maintaining the equipment in

safe conditions.

Use only in perfect technical conditions

The machinery or equipment must be used in perfect tech-

nical condition. Remove immediately any defects that may

affect the safe conditions of use.

• Before starting to use this equipment it is important to take

knowledge of all the controls of the machine, all its functions

and its correct installation in order to avoid accidents to pe-

ople and damage to the machine itself. In particular, it is

important to know how to stop the equipment quickly in case

of emergency.

• Do not allow the use of the machine to people unless pre-

viously instructed with all the information for a proper, safe

use.

• Forbid the access in the operational area to non authorized

personnel, children and pets so as to protect them from pos-

sible injury caused by any part of the machine.

SAFETY PRECAUTIONS DURING HANDLING AND TRAN-

SPORTATION

• Lift the machine using only the points allocated for this fun-

ction.

The lifting eye (or eyes) and the correct positioning of the

forks of the forklift are marked with specic adhesives.

• Clear the operational area of possible obstacles and all un-

necessary personnel.

• Always use lifting equipment properly sized and controlled

by enabled bodies.

• It is forbidden to set on the frame of the equipment objects

or accessories that alter weight and center of gravity and

cause stresses not foreseen to the lifting points.

• Do not submit the machine and the lifting equipment to

swinging or shock which may transmit dynamic stress to the

structure.

Equipments with trailers or site tows

• Never drag the machine without trailer (or site tow)

• Check for a correct assembly of the machine to the towing

device.

• Always make sure that the hook of the vehicle is suitable for

towing of the total mass of the trailer.

• Do not tow the trailer if the coupling devices are worn or

damaged.

• Check for proper tire pressure.

• Do not replace the tires with types different from the original

ones.

• Check that the brakes and the optical signaling of the trailer

are working properly.

• Verify that the bolts of the wheels are in place and well

tightened.

• Do not park the machine (on trailer or site tow) on a steep

slope.

For the stops, not followed by a work session, always enga-

ge the parking brake and / or block the wheels by means of

wheel chocks.

• Do not tow the trailer on bumpy roads.

• Do not exceed the maximum permissible speed on public

roads of 80 km/h with the trailer, in any case comply with the

legislation applicable in the country of use.

• Do not use the site tow on public roads, this is intended for

use only in private and delimited areas. The maximum per-

mitted speed is 40 km/h on smooth surfaces (asphalt or con-

crete), adapt in each case the speed to the type of ground.

13/11/14 M2-5 (TS)_EN

ENGLISH

2.5.1

SAFETY PRECAUTIONS DURING INSTALLATION AND USE

Do not instal equipments closed to heat source, to explosion

or re risk area.

10°

 = 20° max

10°

 = 20°

max

Always locate the machine on a at and solid ground, so as to

avoid tipping, slipping or falling during operation. Avoid using

the machine on slopes greater than 10 degrees.

1,5 m

5 m

GAS

DI SCARICO

Make sure the area immediately surrounding the machine is

clean and free from debris

Do not place objects or obstructions in the vicinity of the air

intakes and air outlets, a possible overheating of the generator

could cause a re.

Connect the machine to an earthing system according to the

regulations in force at the place of installation.

Use the ground terminal on the front of the machine.

Do not use the machine with wet or damp hands and / or

clothing.

Use plugs suitable for the output sockets of the machine and

make sure that electrical cords are in good condition.

The machine must always be positioned so that the exhaust

gases are dispersed in the air without being inhaled by people

or living beings.

If you use the machine indoors is necessary that the installa-

tion is designed and built by skilled technicians in a workmanli-

ke manner.

During normal operation, keep doors closed. The access to

the internal parts should be allowed only for maintenance re-

asons.

Keep area near to the mufer free from objects such as rags,

paper, cardboard. The high temperature of the mufer could

cause the burning of objects and cause re

Immediately stop the machine in case of malfunction.

Do not restart the machine without rst having found and xed

the problem.

SAFETY RULES

ENGINE DRIVEN WELDERS

EXHAUST OUTPUT

REV.0-01/18

13/11/14 M2-5 (TS)_EN

ENGLISH

2.5.2

SAFETY PRECAUTIONS DURING MAINTENANCE

Make use of qualied personnel to carry out maintenance and troubleshooting

It is mandatory to stop the engine before performing any main-

tenance on the machine.

Always use protective devices and suitable equipment.

Do not touch the engine, the exhaust pipes and the mufer

during operation or immediately after. Allow the engine to cool

before performing any operation

With the machine running pay attention to moving parts such

as fans, belts, pulleys.

Do not remove the protections and the safety devices unless

absolutely necessary, restore them after completion of the

maintenance or repair.

Do not refuel while the engine is running or hot.

Do not smoke or use naked ames when refueling.

Refuel only outdoors or in well ventilated areas.

Avoid spilling fuel, especially on the engine.

Clean and dry any leaks before restarting the machine

FUEL

Slowly unscrew the cap of the fuel tank and put it back always

after refueling.

Do not ll the tank completely to allow for expansion of the

fuel inside

Do not remove the radiator cap when the engine is running or

still hot, the coolant may spurt out and cause serious burns

Do not handle the battery without the use of protective gloves,

the battery uid contains sulfuric acid, which is very corrosive

and dangerous

Do not smoke, avoid any naked ames or sparks near the

battery, the vapors exhaled could cause the battery to explode

SAFETY RULES

ENGINE DRIVEN WELDERS

REV.0-01/18

13/11/14 M2-5 (TS)_EN

ENGLISH

2.5.3

ADDITIONAL REQUIREMENTS FOR ENGINE DRIVEN WELDERS

Do not touch parts with OCV, it can cause mortal shock or

heavy born.

OCV is active at welding stick and auxiliary side when welding

generating set is working.

Do not manage electric devices and welding stick whit feet,

hands or wet dresses.

Protect yourself from electric shock by insulating yourself from

work and ground.

Use non-ammable, dry insulating material if possible, or use

dry rubber amts, dry wood or plywood, or other dry insulating

material.

Magnetic elds can affect pace-makers. Pace-maker wearers

keep away from arc welding and cutting operations and

equipment.

Wearers should consult their doctor before going near arc

welding, gouging, arc cutting, or spot welding operations.

Breathing welding fumes can be hazardous to your health.

Keep your out of the fumes

Use enought ventilation, exhaust at the arc, or both, to keep

fumes and gases from your breathing zone and the general

area.

If adequancy of ventilation or exhaust is uncertain, have the

air quality checked.

Arc rays can burn eyes and skin.

Use welding helmet with correct shade of lter.

While working protect your eyes using glasses with lateral

screen and your head with dedicated cap; in case of restricted

working area or unsafe working position also protect your

ears.

Wear complete body protection. Wear oil free protective

clothing such as leather gloves, heavy shirt, cufess pants,

and hight boots.

Welding can cause re or explosion.

Have a re extinguisher nearby, and have a trained re

watcher ready to use it.

Do not weld near ammable material. Move ammanles at

least (10 m) away or protect them with ame-proof covers.

Do not weld containers, structures, etc. with fammable

materials inside (tank, cylinder, etc.); in case you need to weld,

verify such items by qualied person in order to fully safely

operate.

Hot parts can cause severe burns.

Don’t touch the welder with bare hand. If handling is needed,

use proper tools and/or wear heavy, insulated welding gloves

to prevent burns.

Allow cooling period before handing parts or working on gun

or torch.

SAFETY RULES

ENGINE DRIVEN WELDERS

REV.0-01/18

26/11/08 C0DN6000_EN

ENGLISH

REV.0-12/19

DESCRIPTION OF THE MACHINE

The MAGIC WELD 200 engine driven welder is a unit which ensures the dual function as:

a) a current source for are welding

b) current generator for generating auxiliary

Unit meant for industrial and professional use. Powered by an endothermic engine; it is composed of various parts such as:

engine, alternator, electric and electronic controls, the fairing at a protective structure.

The assembling is made on a steel structure, on which are provided elastic support which must damp the vibrations and also

eliminate sounds which would produce noise.

ALTERNATOR

FRONT

PANEL

FRAME

ENGINE

VIBRATION

DAMPER

FUEL TANK

CAP

MUFFLER

ENGINE

AIR FILTER

OIL LEVEL DIPSTICK

+ ENGINE OIL

RESERVOIR CAP

STARTER

HANDLE

CHOKE CONTROL

FUEL VALVE

STOP LEVER

OIL DRAIN CAP

0.1

RECORDING DATA

REV.1-11/14

The manual is for the range of machines indicated on the front cover.

With the scope to facilitate the search of the spare parts and maintain information of the bought machine, is necessary to record

some data.

Please write the requested data inside the squares to side:

1. Model of machine

2. Serial number of the machine

3. Serial number of the engine

4. Name of the dealer where bought the machine

5. Address of the dealer

6. Phone number of the dealer

7. Date of the bought machine

8. Notes

RECORDING DATA

16/10/15 Registrazione Dati_EN

ENGLISH

26/11/08 C0DN6000_EN

ENGLISH

NOTE

+ Be sure that the lifting devices are: correctly mounted,

adequate for the weight of the machine with it’s packaging,

and conforms to local rules and regulations.

When receiving the goods make sure that the product has

not suffered damage during the transport, that there has

not been rough handling or taking away of parts contained

inside the packing or in the set.

In case you nd damages, rough handling or absence of

parts (envelopes, manuals, etc.), we advise you to inform

immediately our Technical Service.

For eliminating the packing materials, the User must

keep to the norms in force in his country.

1) Take the machine (C) out of the shipment packing.

Take out of the envelope (A) the user’s manual (B).

2) Fit the handle as shown in the instructions (tting: screws

and spanner are supplied).

3) Read: the user’s manual (B), the plates xed on the ma-

chine, the data plate.

In case you should transport or move the machine, keep to the instructions as per the gures.

Be sure that the lifting devices are: correctly mounted, adequate for the weight of the machine with it’s packaging, and conform

to local rules and regulations.

Only authorized persons involved in the transport of the machine should be in the area of movement.

UNPACKING AND TRANSPORT

REV.0-12/19

02/12/19 C0DN6000_IT

2.7

IINSTALLAZIONE E DIMENSIONI - INSTALLATION AND DIMENSIONS - INSTALLATION ET DIMENSIONS

LUFTZIRKULATION UND ABMESSUNGEN - INSTALACIÓN Y DIMENSIONES - INSTALAÇÃO E DIMENSÕES

REV.0-12/19

13/09/18 M2-6 (TS) EN

ENGLISH

If is needed to move the

welder machine be sure

that the engine is off, that

no electric connection is on

and that noone cable will

avoid to move the welder

machine.

The wrong loads distribution can cause

the instability of the vehicle and abnorma-

lities to wheel and components. In case of

transport need, use dedicated vehicle for

this purpose. The loads must be balan-

ced, xed in order to guaranty the stability

of the vehicle. Do not exceed the max load suitable of the vehi-

cle with reference to axle, wheels, etc. Fix the base of welder

machine at the frame or platform observing the instruction of

the vehicle producer

INSTALLATION AND ADVICE BEFORE USE

The operator of the welder is responsible for the security of the

people who work with the welder and for those in the vicinity.

Before installing the welder machine, read the safety instruction

of this manual at the chapter 2.5.

Particulary remember:

- installing operation must be made by authorized and qualied

person.

- while installing operation use individual safety devices (shoes,

gloves, cap, etc.)

INSTALLATION

FIxINg

MOVINg THE WELDER MACHINE

INSTALLATION ON VEHICLE

ATTENTION

This equipment is designed for outdoor use. It

may be stored, but is not intended to be used

when welding outside during precipitation unless

sheltered

2.6

INSTALLATION AdvIceS

eNGINe dRIveN WeLdeR

REV.0-09/18

DANgER

The machine must be positioned so that exhaust gas is dif-

fused without being inhaled by any living being.

Engine exhaust gas contains carbon monoxide, which is

harmful to one’s health, and in big quantities can cause in-

toxication and death.

Local norms in force have to be respected.

ATTENTION

A safe distance has to be kept between the machine and

fuel deposits, inammable goods (cloths, paper, etc.), che-

micals, according to indications provided by the authority in

charge. In order to avoid potentially dangerous situations,

area surrounding genset should be isolated so that unau-

thorized people will not be able to get close to the unit. Even

if The machines are manufactured according to electroma-

gnetic compatibility norms, we suggest NOT to install the

genset near machinery that can be inuenced by magnetic

elds.

Always instal the welder machine

on a hard and plan surface in order

to avoid rollovers, slips or falls whi-

le working;

avoid to use the welder machine

with slope more than 10°.

In order to absorb vibrations produced by gen-

set, it should be xed to a surface with suf-

cient rigidity, isolated against vibrations to-

wards other structures and with a mass equal

to at least three times the genset mass.

If such above could not be possible, be sure

that the welding machine do not move or slip

while working due to vibrations;

be care to x the welder machine with dedica-

ted tools.

24/10/19 C0CN50A09_EN

ENGLISH

PREDISPOSIZIONE ED USO

REV.0-10/19

ATTENTION

Gasoline is highly ammable.

Refuel with motor shut off in a at surfaced well-

ventilated area.

Do not refuel in the presence of ames. Avoid

spilling fuel.

Any eventual spilled fuel and fumes are ammable.

Clean any dispersions of fuel before starting up the

motor.

LUBRICANT

Please refer to the motor operating manual for the recommen-

ded viscosity.

To check the oil level:

1. Remove the oil-ll tap (24) and clean the dip-stick (23).

2. Insert the dip-stick into the oil ller without screwing it in.

3. If the oil level is low, ll with recommended oil up to the top

of the oil ller

MOTORS WITH OIL ALERT DEVICE

The “Oil Alert” system is designed to prevent damage to the

motor due to an insufcient quantity of oil in the cup. This sy-

stem automatically shuts off the motor before the oil level falls

below the safety limit.

If the motor does not start up again after shutting itself off,

check the oil level.

Oil ll tap / dip-stick

Upper oil level

FUEL

Fill the tank with gasoline for automobiles (preferably lead

free or with low lead content in order to reduce deposits in the

combustion chamber to a minimum).

For further details on the type of gasoline to use, see the motor

operating manual supplied.

Do not ll the tank completely; leave a space of approx. 10

mm between the fuel level and the wall of the tank to allow for

expansion.

AIR FILTER

Check that the dry air lter is correctly installed and that there

are no leaks around the lter which could lead to inltrations of

non-ltered air to the inside of the motor.

WARNING

Do not use the machine if it is not in good technical

condition

The machine must be in good working order before being

used. Defects, especially those which regard the safety of

the machine, must be repaired before using the machine.

Do not use without protective devices provided

Removing or disabling protective devices on the machine

is prohibited.

24/10/19 C0CN50A09_EN

ENGLISH

STARTING AND STOPPING THE ENGINE

REV.0-10/19

Check daily

STARTING

FUEL COCK

2. Switch the choke control to CLOSE

N.B.: Do not use the air valve if the motor is hot or the air

temperature is too high

CHOKE LEVER

3. Turn the engine switch to the ON position

ENGINE SWITCH

STARTER GRIP

Lightly pull the start-up knob until meeting resistance, then pull

decisively.

 ATTENTION:

Allow the start-up knob to re-enter slowly, avoiding having it

knock against the motor and thereby damaging the start-up

system.

4. When the engine is started the machine reaches maximum

engine speed immediately (4000 rpm) for 6/7 seconds, after

which the engine speed automatically decreases to minimum

(2000 rpm). The minimum is set by the solenoid which acts

on the accelerator lever.

5. The engine reaches maximum speed only when current is

drawn in welding or auxiliary power mode.

NOTE

Do not alter the primary conditions of regulation and do not

touch the sealed parts.

STOPPING

 Before stopping the engine it is compulsory:

- Disconnect or close any power load connected to the system’s

auxiliary generation

- interrupt welding.

To shut down the motor:

For shut down the motor in case of emergency, turn the motor

switch to OFF.

In normal conditions, wait for the engine to reach minimum

speed automatically 6/7 seconds after the load has been exclu-

ded. Turn the engine in these conditions for a few minutes so

that it can cool down and then turn the engine switch to OFF.

Turn the fuel valve to the OFF position.

ENGINE SWITCH

FUEL VALVE

1. Turn the fuel cock to ON.

02/12/19 C0DN6000_IT

COMANDI - CONTROLS - COMMANDES - MANDOS - BEDIENELEMENTE - COMANDOS

СИСТЕМЫ УПРАВЛЕНИЯ - BEDIENING

REV.0-12/19

Pos. Descrizione Description Description

Referenzliste

9 Prese di saldatura (+) Welding sockets (+) Prises de soudage (+) Schweißbuchse ( + )

10 Prese di saldatura (-) Welding sockets (-) Prises de soudage (-) Schweißbuchse ( - )

12 Presa di messa a terra Earth terminal Prise de mise à terre Erdanschluß

15 Presa di corrente in c.c. d.c. socket Prises de courant en c.c. Steckdose AC

S8 Led Overload Overload led Voyant Surcharge Led Überbelastung

T Regolatore corrente di saldatura Welding current regulator Régulateur courant soudage Schweißstromregler

910

SCHUKO

vers.

AUS

vers.

26/11/08 C0DN6000_EN

ENGLISH

PUSH AND

TWIST

CONNECT WELDING CABLES

Insert the welding cable plugs completely in the sockets, turning

clockwise to lock them in place.

Connect the earth clamp to the negative pole and the electrode

holder to the positive.

+ Pay attention to the two polarities on the welding circuit,

which must not come into electrical contact with each other.

- Carefully tighten the output cables to the bushings; if loose,

they can cause problems of overheating and damage the

bushings, cables, etc.

- Make certain the grounding pincer is connected as near as

possible to the work station.

ADJUSTING THE WELDING CURRENT

The welding current is regulated by turning knob “T” conti-

nuously. If set to the minimum (turned fully in an anticlockwise

direction) it provides a current of approximately 30 A; if set to

the maximum (turned fully in a clockwise direction) it gives a

maximum current of approximately 200A (20V).

RECOMMENDED ELECTRODES

All the electrodes on the market can be used.

USE AS A WELDER

REV.0-12/19

WARNING

Areas for which access by non-authorized personnel is

forbidden are:

- the control panel (at the front) - the endothermic motor

discharge.

ATTENTION

To reduce the risk of electromagnetic interference, keep the

welding cable length short and keep them on or near the

ground. If possible, welding operations should not be done

near sensitive electronic devices. If interference continues

to occur, adopt additional measures: shift the group, use

shielded cables, line lters, shield the entire work area.

If the above solutions do not sufce, consult our Technical

Servicing Department.

La pagina sta caricando ...

Mosa Magic Weld 200 Manuale del proprietario

Marca: Mosa

Modello: Magic Weld 200

Categoria: Sistema di saldatura

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Mosa Magic Weld 200 Owner's manual

Mosa Magic Weld 200 Manuale del proprietario

Mosa Magic Weld 200 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti