Pyronix Matrix Series Guida d'installazione

Matrix Installation Guide

This Guide Supports the Following Panels:

MATRIX 832

MATRIX 832+

MATRIX 424

RINS428-5

Tel: +44(0) 1709 700100

Pyronix Association of Security Specialists

Installer Support

The Pyronix Association of Security specialists has been developed with the focus on what you the installer

would like to see from one of the leading manufactures of security equipment.

The philosophy behind the association is that you will receive tangible benefits, which are applicable to both

the work and home environment.

The Association Awards Catalogue

By collecting the tokens which are printed on the packaging you can redeem against gift vouchers for Argos,

Marks & Spencer and Whitbread Leisure.

Product Consultation

Product training and consultation evenings are provided up and down the country.

To join PASS please contact our marketing department:

[email protected]

Tel: +44 (0)1709 700100

technical.support@pyronix.com

As a new member of PASS you will be issued with a free technical support telephone number.

Matrix 832 / 832+ / 424

RINS428-5 Page i

Contents

SECTION 1: TECHNICAL SPECIFICATIONS & SYSTEM OVERVIEW ..............................1

1.1 Technical Specifications........................................................................................................1

1.1.1 Main Control Panel............................................................................................................................1

1.1.2 Additional Expanders ........................................................................................................................3

1.2 Battery Capacity Calculations...............................................................................................4

1.2.1 UK Requirements..............................................................................................................................4

1.2.2 Norwegian & Danish Requirements..................................................................................................4

1.2.3 Swedish Requirements .....................................................................................................................4

1.3 System Overview....................................................................................................................5

SECTION 2: SAFETY & APPROVALS ................................................................................9

SECTION 3: MOUNTING PROCEDURE............................................................................14

3.1 Mounting Procedure for Matrix – Plastic & Metal Case ....................................................14

3.2 Panel Layout – Plastic Case ................................................................................................14

3.3 Panel Layout – Metal Case ..................................................................................................15

3.4 Battery Installation Procedure ............................................................................................15

SECTION 4: CABLING RULES FOR THE MATRIX BUS..................................................16

4.1 System Examples .................................................................................................................17

SECTION 5: OPERATING MODES....................................................................................19

5.1 Disarmed Mode.....................................................................................................................19

5.2 Armed Mode..........................................................................................................................19

5.3 Arm Mode ..............................................................................................................................19

5.4 Entry / Exit Mode ..................................................................................................................19

5.5 Alarm Mode ...........................................................................................................................19

5.6 Anti-Code Reset....................................................................................................................19

5.7 First to Alarm Mode..............................................................................................................20

5.8 Engineer Mode......................................................................................................................20

5.9 User Mode .............................................................................................................................20

SECTION 6: KEYPAD/READER SYMBOLS & INDICATIONS..........................................21

6.1 The ICON Keypad .................................................................................................................21

6.2 The LCD Keypad...................................................................................................................22

6.3 The Proximity Reader...........................................................................................................22

SECTION 7: PROGRAMMING THE SYSTEM ...................................................................23

7.1 Addressing the LCD & ICON Keypads ...............................................................................23

7.2 Addressing the Proximity Reader.......................................................................................24

7.2.1 Connection of MX PROX to a PC ...................................................................................................24

7.3 Finding Bus Devices ............................................................................................................25

7.4 Factory Default Settings of Matrix System ........................................................................25

7.4.1 Engineer Code ................................................................................................................................25

7.4.2 Global System Options ...................................................................................................................25

7.4.3 Zone Types, Zone Attributes & Zone Settings................................................................................26

7.4.4 User Codes, User Code Attributes & Proximity Card Allocation.....................................................27

7.4.5 Keypads & Proximity Readers Partition Allocation .........................................................................27

7.4.6 System & Tamper Faults Partition Allocation..................................................................................27

7.4.7 Partition Options..............................................................................................................................27

7.4.8 Arm Options ....................................................................................................................................27

7.4.9 System Timers ................................................................................................................................28

7.4.10 Programmable Outputs.................................................................................................................28

7.4.11 Digital Communicator....................................................................................................................29

7.4.12 Communication Formats...............................................................................................................29

7.4.13 Events Reporting...........................................................................................................................29

7.4.14 DD243 Option Defaults .................................................................................................................30

7.4.15 Confirmation Timer Defaults .........................................................................................................30

7.4.16 Zone Mapping Defaults.................................................................................................................31

Matrix 832 / 832+ / 424

Page ii RINS428-5

7.5 Entering / Exiting Engineer Mode .......................................................................................32

7.5.1 Entering Engineer Mode................................................................................................................. 32

7.5.2 Exiting Engineer Mode ................................................................................................................... 32

7.5.3 Changing Engineer Code............................................................................................................... 32

7.6 Global System Options ........................................................................................................33

7.6.1 System Options 1 ........................................................................................................................... 39

7.6.2 System Options 2 ........................................................................................................................... 39

7.6.3 System Options 3 ........................................................................................................................... 39

7.7 Zone Types, Configuration, Attributes & Partition Allocation..........................................40

7.7.1 Zone Types..................................................................................................................................... 44

7.7.2 Zone Configuration......................................................................................................................... 44

7.7.3 Zone Names Programming from LCD Keypad .............................................................................. 47

7.7.4 Key Map Tables.............................................................................................................................. 48

7.8 User Codes & User Attributes .............................................................................................49

7.8.1 Programming User Codes.............................................................................................................. 52

7.8.2 User Code Partition Allocation ....................................................................................................... 52

7.8.3 User Code Attributes Allocation ..................................................................................................... 52

7.8.4 Temporary Code............................................................................................................................. 52

7.8.5 Assigning / Clearing Proximity Card to / from User Code .............................................................. 52

7.9 Keypads & Proximity Readers Partition Allocation...........................................................53

7.9.1 Icon Keypad Programming............................................................................................................. 55

7.9.2 LCD Keypad Programming ............................................................................................................ 55

7.9.3 Proximity Reader Programming ..................................................................................................... 58

7.9.4 Changing Default Language on LCD Keypad................................................................................ 58

7.10 System Faults & Tamper Alarms Warning Allocation .....................................................59

7.10.1 System Faults (Warning Partition Allocation)............................................................................... 59

7.10.2 Bell And Tamper Faults (Warning Partition Allocation)................................................................ 59

7.11 Partition Options.................................................................................................................60

7.11.1 Partition Options 1........................................................................................................................ 62

7.11.2 Partition Options 2........................................................................................................................ 63

7.12 Arm Options ........................................................................................................................63

7.12.1 Exit Terminator Type for Arm Mode A.......................................................................................... 65

7.12.2 Exit Terminator Type for Arm Mode B.......................................................................................... 65

7.12.3 Exit Terminator Type for Arm Mode C ......................................................................................... 66

7.12.4 Exit Terminator Type for Arm Mode D ......................................................................................... 66

7.12.5 Home & Away Allocation .............................................................................................................. 66

7.12.6 Partition Dependency ................................................................................................................... 66

7.12.7 Keyswitch Zone Arm Mode Allocation.......................................................................................... 67

7.12.8 Number of Rearms ....................................................................................................................... 67

7.13 System Timers ....................................................................................................................68

7.13.1 Bell Time....................................................................................................................................... 70

7.13.2 Bell Time Delay ............................................................................................................................ 70

7.13.3 Entry Time .................................................................................................................................... 70

7.13.4 Exit Time....................................................................................................................................... 70

7.13.5 Final Exit Delay............................................................................................................................. 70

7.13.6 Auto-Arm Commencing Time – Every Day .................................................................................. 70

7.13.7 Inactivity Auto-Arm ....................................................................................................................... 70

7.13.8 AC Fail Warning & Report Delay.................................................................................................. 70

7.13.9 Telephone Line Fail Warning & Report Delay.............................................................................. 70

7.13.10 Seconds in Last Minute of the Day ............................................................................................ 70

7.14 Programmable Outputs......................................................................................................71

7.14.1 PGM Programming....................................................................................................................... 74

7.14.2 Zone to Follow in Partition............................................................................................................ 74

SECTION 8: COMMUNICATION PROGRAMMING .......................................................... 75

8.1 Digital Communicator ..........................................................................................................76

8.1.2 Account Codes & Account Partition Allocation............................................................................... 78

8.1.3 Up / Down Loading Access Code................................................................................................... 78

8.1.4 Digital Communicator Options 1..................................................................................................... 78

8.1.5 Digital Communicator Options 2..................................................................................................... 78

8.1.6 Test Dial Time ................................................................................................................................ 78

8.1.7 Test Dial Interval ............................................................................................................................ 78

8.1.8 Telephone Number 1 Allocation..................................................................................................... 78

Matrix 832 / 832+ / 424

RINS428-5 Page iii

8.1.9 Telephone Number 2 Allocation......................................................................................................78

8.1.10 Telephone Number 3 Allocation....................................................................................................79

8.1.11 Test Dial Sequence (Group Reporting).........................................................................................79

8.1.12 Anti-Code Algorithm Number ........................................................................................................79

8.2 Reporting Formats ...............................................................................................................79

8.2.1 Telephone Number Programming & Format Allocation ..................................................................82

8.2.2 BSIA Format Channel Map .............................................................................................................83

8.3 Send Options & Group Reporting Sequence.....................................................................83

8.3.1 Disarmed Mode Events Send Options............................................................................................85

8.3.2 Arm Mode A Events Send Options .................................................................................................85

8.3.3 Arm Mode B Events Send Options .................................................................................................85

8.3.4 Arm Mode C Events Send Options .................................................................................................86

8.3.5 Arm Mode D Events Send Options .................................................................................................86

8.3.6 Restoral Events Send Options........................................................................................................86

8.3.7 Allocating Telephone Numbers to Alarm Types in Partitions..........................................................87

8.3.8 MX Voice Module Support ..............................................................................................................87

8.3.9 Change Number of Voice Dials.......................................................................................................87

SECTION 9: INSTALLING DD243......................................................................................88

9.2 Zone Mapping .......................................................................................................................88

9.3 Means of Setting (Arming) and Unsetting (Disarming).....................................................88

9.4 Resetting Following an Alarm Condition ........................................................................... 89

9.5 Mis-Operation Signals..........................................................................................................89

9.6 DD243 Options Table ...........................................................................................................90

9.7 DD243 Options 1...................................................................................................................92

9.8 DD243 Zone Map...................................................................................................................92

9.9 DD243 Partition Confirmation Times .................................................................................. 92

SECTION 10: EVENTS MEMORY LOG & SYSTEM MAINTENANCE ..............................93

10.1 Reading The Event Log......................................................................................................93

10.1.2 Viewing Event Log Memory ..........................................................................................................94

10.2 System Faults & Maintenance........................................................................................... 99

10.2.1 NVM Reset to Factory Default ......................................................................................................99

10.2.2 Programmable Outputs Test.........................................................................................................99

10.2.3 Walk Test ......................................................................................................................................99

10.2.4 Scan for Devices on the Bus.........................................................................................................99

10.2.5 Local Up / Down Loading Session (RS232)................................................................................100

10.2.6 Engineer Code NVM Reset to Factory Default ...........................................................................100

10.2.7 Programmable Outputs Test.......................................................................................................100

10.2.8 Walk Test ....................................................................................................................................100

10.2.9 Scan For Devices On the Bus.....................................................................................................100

10.2.10 Local Up / Down Loading using RS232 Output ........................................................................100

SECTION 11: UDL PC SOFTWARE DATA MANAGEMENT...........................................101

11.1 Customer Explorer ...........................................................................................................101

11.2 Editing Customer Information......................................................................................... 103

11.2.1 Global Information.......................................................................................................................104

11.2.2 Principal Contact .........................................................................................................................104

11.2.3 Keyholders ..................................................................................................................................104

11.2.4 Partition Information....................................................................................................................104

11.3 Exporting and Importing Customers .............................................................................. 105

11.4 Entering Panel Details & Uploading/Downloading to the Panel...................................106

11.4.1 Default Records ..........................................................................................................................107

11.4.2 Normal Dial to the Panel .............................................................................................................108

11.4.3 AMC Dial to the Panel.................................................................................................................108

11.4.4 Local Connection ........................................................................................................................109

11.4.5 Dial Back .....................................................................................................................................109

11.4.6 Sending Data to a Panel .............................................................................................................109

11.4.7 Getting Data from a Panel...........................................................................................................109

11.4.8 Verifying Panel Details................................................................................................................109

11.4.9 12.4.9 Online Panel Information .................................................................................................110

Matrix 832 / 832+ / 424

Page iv RINS428-5

11.5 Modem Settings ................................................................................................................111

11.5.1 Modem Types............................................................................................................................. 111

11.5.2 Configuring Communications Options........................................................................................ 111

11.5.3 Configuring Dial Options ............................................................................................................ 112

11.5.4 Configuring Dial Back Options ................................................................................................... 113

11.5.5 Configuring Computer Network Options .................................................................................... 114

11.5.6 Character Set Options................................................................................................................ 115

11.5.7 Customer Map............................................................................................................................ 116

11.5.8 Configuring Other Options.......................................................................................................... 117

11.6 Using Help .........................................................................................................................118

SECTION 12: INSTALLATION, SERVICE & MAINTENANCE........................................ 119

12.1 Scanning for Devices .......................................................................................................120

12.2 Matrix 832 PCB..................................................................................................................123

12.3 Matrix 832+ PCB................................................................................................................124

12.4 Matrix 424 PCB..................................................................................................................125

12.5 Matrix Voice Module .........................................................................................................126

12.5.1 Programming the Voice Module................................................................................................. 126

12.5.1 Voice Module Connections to Matrix 832+................................................................................. 127

12.6 MX-BATT Battery Monitor Board.....................................................................................128

12.7 Matrix Zone Expanders ....................................................................................................129

12.7.1 Local Plug-On 8 Zone Expander................................................................................................ 129

12.7.2 MX-RIX with Zone Analyser ....................................................................................................... 131

12.8 Matrix PGM Expanders.....................................................................................................136

12.8.1 MX-ROX8R/8T Connections to 832 ........................................................................................... 137

12.8.2 MX-ROX8R/8T Connections to 832+......................................................................................... 138

12.9 Keypads & Proximity Readers Connections..................................................................139

12.9.1 Connecting a Single Keypad to Matrix 832................................................................................ 139

12.9.2 Connecting a Single Keypad to Matrix 832 +............................................................................. 140

12.9.3 Connecting Multiple Keypads to a Matrix 832 – Daisy Chain .................................................... 141

12.9.4 Connecting Multiple Keypads to a Matrix 832 – Star Configuration........................................... 142

12.9.5 Connecting Proximity Readers to a Matrix 832.......................................................................... 142

12.9.6 Connecting Proximity Readers to a Matrix 832+........................................................................ 143

12.10 Connecting a Matrix to a Telephone Line.....................................................................143

12.11 Zone Wiring Diagrams....................................................................................................144

12.11.1 Zone Doubling to Matrix 832 .................................................................................................... 144

12.11.2 Zone Doubling to Matrix 832+ .................................................................................................. 145

12.11.3 Zone Doubling to Matrix 424 .................................................................................................... 146

12.11.4 Normally Closed Zones to Matrix 832 ...................................................................................... 147

12.11.5 Double End of Line Resistors to Matrix 832............................................................................. 147

12.11.6 Double End of Line Resistors to Matrix 832+........................................................................... 148

12.12 Programmable Outputs Connections ...........................................................................149

12.12.1 Belle Connection to Matrix 832 ................................................................................................ 149

12.12.2 Belle Connection to Matrix 832+ .............................................................................................. 150

12.12.3 Belle Connection to Matrix 424 ................................................................................................ 151

12.12.4 Decibell Connection to Matrix 832 ........................................................................................... 152

12.12.5 Decibell Connection to Matrix 424 ........................................................................................... 152

12.12.6 Twin Alert Connection to Matrix 832 ........................................................................................ 153

12.12.7 Twin Alert Connection to Matrix 832+ ...................................................................................... 154

12.12.8 Twin Alert Connection to Matrix 424 ........................................................................................ 155

12.12.9 Vocaliser Connection to Matrix 832 ......................................................................................... 155

12.12.10 Vocaliser Connection to Matrix 832+ ..................................................................................... 156

12.12.11 Two Wire Fire Detector Connection to Matrix 832 ................................................................. 157

12.12.12 Normally Open Four Wire Fire Detector Connection to Matrix 832 ....................................... 157

12.12.13 Buzzer, LED & any Siren Connection to PGM on Matrix 832................................................ 158

12.12.14 High-Powered Siren Connections for Matrix 832 / 832+ / 424............................................... 158

SECTION 13: PARTITION MANAGEMENT .................................................................... 159

13.1 Example 1 ..........................................................................................................................159

13.2 Example 2 ..........................................................................................................................160

SECTION 14: ENGINEER QUICK PROGRAMMING GUIDE .......................................... 161

! Matrix 832 / 832+ / 424

RINS428-5 Page 1

Section 1: Technical Specifications & System Overview

1.1 Technical Specifications

1.1.1 Main Control Panel

Matrix 832+ Matrix 832 Matrix 424

ZONES

Zone Loop Current

0.54mA - Max 0.54mA - Max 0.54mA - Max

Zone Activation Resistance

DEOL

Short circuit

<800Ω <800Ω <800Ω

Normal

>800Ω to <6kΩ >800Ω to <6kΩ >800Ω to <6kΩ

Activated

>6kΩ to <36kΩ >6kΩ to <36kΩ >6kΩ to <36kΩ

Open circuit

>36kΩ >36kΩ >36kΩ

Normally Closed

Normal

<4kΩ <4kΩ <4kΩ

Activated

>4kΩ >4kΩ >4kΩ

Doubled

Both zones Normal

>2kΩ to <6kΩ >2kΩ to <6kΩ >2kΩ to <6kΩ

Both zones Activated

>11kΩ to <35kΩ >11kΩ to <35kΩ >11kΩ to <35kΩ

Zone n Activated

>8kΩ to <11kΩ >8kΩ to <11kΩ >8kΩ to <11kΩ

Zone n+16 Activated

>6kΩ to <8kΩ >6kΩ to <8kΩ >6kΩ to <8kΩ

Zone Doubled: Tamper

Activated

<2kΩ or >35kΩ <2kΩ or >35kΩ <2kΩ or >35kΩ

Zone Response Time

Standard Zones

350ms 350ms 350ms

Fast Zones

100 ms 100 ms 100 ms

Only Zone 1 Fast

Zone1 - 30ms

Other zones - 350ms

Zone1 - 30ms

Other zones - 350ms

Zone1 - 30ms

Other zones - 350ms

Zone Protection

18V Varister 18V Varister N/A

PROGRAMMABLE OUTPUTS (PGM)

PGM 1

Relay contacts

30V@3A

Relay contacts

30V@3A

Relay contacts

30V@3A

PGM 2

Relay contacts

30V@3A

Open Collector

12V@200mA

Open Collector

12V@200mA

PGM 3

Open Collector

12V@200mA

Open Collector

12V@ 200mA

Open Collector

12V@200mA

PGM 4

Open Collector

12V@10mA

Open Collector

12V@10mA

Open Collector

12V@10mA

DIGITAL COMMUNICATOR

Telephone Line Monitoring

Yes Yes Yes

Digital Communicator

Analogue Line Analogue Line Analogue Line

Lightning Protection

Heavy duty protection

6.75kV / 125A

Heavy duty protection

6.75kV / 125A

Heavy duty protection

6.75kV / 125A

POWER SUPPLY

Power Input

17Vac 17Vac 17Vac

Transformer Rating

44VA (Metal case)

21VA (Plastic case)

21VA 21VA

EN50131-6 Type

A A A

Voltage Output

13.6Vdc@1A regulated

Max 13.8V Min 10.5V

13.6Vdc@1A regulated

Max 13.8V Min 10.5V

13.6Vdc@1A regulated

Max 13.8V Min 10.5V

Ripple

1% Max. 1% Max 1% Max

Total Current Output

AUX, Bell, K+

600mA (Plastic)

1.1A (Metal)

600mA 600mA

Panel Current Requirement

200mA 200mA 200mA

Matrix 832 / 832+ / 424

Page 2 RINS428-5

Matrix 832+ Matrix 832 Matrix 424

FUSES

Bell fuse

Quick blow 1A – F1L Quick blow 1A – F1L Quick blow 1A – F1L

Aux fuse

Quick blow 1A – F1L Quick blow 1A – F1L N/A

Keypad fuse

Quick blow 1A – F1L N/A N/A

Battery fuse

Slow blow 5A – T5H N/A N/A

BATTERY

Type

12V Lead acid

rechargeable

12V Lead acid

rechargeable

12V Lead acid

rechargeable

Battery Charge

Min 6V Min 6V Min 6V

Maximum Battery Charge

Current

800mA (Metal Case)

350mA (Plastic case)

350mA 350mA

Battery Charge Method

The Matrix panel monitors the voltage of the battery and commences

charging when the battery reaches 12.8V +/- 5% and disables charging

when it reaches 13.6V +/- 5%.

Battery Capacity

Metal Enclosure

2.8 to 17Ah

Plastic Enclosure

2.8 to 7Ah

Plastic Enclosure

2.8 to 7Ah

Plastic Enclosure

2.8 to 7Ah

BAT Terminal Protection

Short circuit & battery

reverse protection.

Short circuit & battery

reverse protection.

Short circuit & battery

reverse protection.

Low Battery Detect Level

10.7V +/- 0.2V 10.7V +/- 0.2V 10.7V +/- 0.2V

Battery Cutoff Level

10.4V +/- 0.2V

(With MX-BATT)

10.4V +/- 0.2V

(With MX-BATT)

10.4V +/- 0.2V

(With MX-BATT)

MECHNICAL

Security Grade

2 (Metal Case)

N/A (Plastic Case)

N/A N/A

Environmental Class

2 (Metal Case)

N/A (Plastic Case)

N/A N/A

Dimensions

Plastic

340 x 280 x 94.5 mm 340 x 280 x 94.5 mm 340 x 280 x 94.5 mm

Metal

389.5 x 314.5 x

96.2mm

N/A N/A

TEMPERATURE

Operational Metal Case

-10 to +55ºC

14 to 131ºF

Plastic Case

0 to +40ºC

32 to 104ºF

0 to +40ºC

32 to 104ºF

0 to +40ºC

32 to 104ºF

Storage

-20 to +60ºC

-4 to 172ºF

-20 to +60ºC

-4 to 172ºF

-20 to +60ºC

-4 to 172ºF

Maximum Humidity

93% Rh (Metal Case) N/A N/A

! Matrix 832 / 832+ / 424

RINS428-5 Page 3

1.1.2 Additional Expanders

PROGRAMMABLE OUTPUT EXPANDERS

TRANSISTOR MX-ROX8T

Supply Voltage

13.8V typical (9-16V range)

Supply Current

45mA +/- 5 % @13.8V

Outputs

Type

Open Collector

Maximum Switching Voltage

12Vdc

Maximum Switching Current

225mA

RELAY MX-ROX8R

Supply Voltage

13.8V typical (9-16V range)

Supply Current

225mA +/- 5 % @13.8V

Outputs

Type

N/O / N/C contacts

Maximum Switching Voltage

30V

Maximum Switching Current

1A

PROGRAMMABLE ZONE EXPANDERS

LOCAL PLUG-ON MX-IX16

Supply Voltage

13.8V typical (9-16V range)

Supply Current

15mA@ +/- 5 % 13.8V

Zone Loop Current

Zone Activation Resistance

See main control panel data

REMOTE MX-RIX with Zone Analyser

Supply Voltage

12V typical (9-16V range)

Supply Current

45mA +/- 5 % @13.8V

Zone Loop Current

Zone Activation Resistance

See main control panel data

PROGRAMMABLE VOICE MODULE

MX-VOICE

Supply Voltage

13.8V typical (9-16V range)

Supply Current

25mA +/- 5 % @13.8V

Matrix 832 / 832+ / 424

Page 4 RINS428-5

1.2 Battery Capacity Calculations

Maximum Battery recharge time must not exceed 72 hours to satisfy EN50131-6.

1.2.1 UK Requirements

In the event of mains failure BS4737 Part 1, Section 7.2.1, specifies that a stand-by battery should be able to

power the system for a non-alarmed period of 8 hours. The typical Local Authority specified maximum bell

alarm period is 20 minutes.

Example Calculation

Non-alarmed condition 7 hrs 40mins = 7.67Hrs:

Control panel 0.130A

Keypad 0.015A

Detectors (8 detectors at 15mA each) 0.120A

External sounder 0.050A

External strobe 0.000A

Total current 0.315A

Amp/hour capacity 0.315A x 7.67h = 2.41Ah

Alarmed condition 20mins = 0.33Hrs:

Control panel 0.130A

Keypad 0.015A

Detectors (8 detectors at 15mA each) 0.120A

External sounder 0.350A

External strobe 0.150A

Total current 0.765A

Amp/hour capacity 0.765A x 0.33h = 0.25Ah

Minimum battery capacity = 2.41A + 0.25A 2.66Ah

WARNING: Consult each product’s instructions for the actual current values.

1.2.2 Norwegian & Danish Requirements

Required capacity = (18 x A) + (0.5 x B)

Where:

A = Maximum non-alarmed total system current.

B = Maximum alarmed total system current.

1.2.3 Swedish Requirements

Required capacity = 12 x A

Where:

A = Maximum total system current.

! Matrix 832 / 832+ / 424

RINS428-5 Page 5

1.3 System Overview

Matrix 832 / 832+ Matrix 424

ZONES

Zones on Main Board

8 fully programmable zones (16

using zone doubling option)

4 fully programmable zones (8 using

zone doubling)

Zone Expander (On Board)

8 fully programmable zones on local

plug In expander (16 using zone

doubling option)

8 fully programmable zones on local

plug In expander (16 using zone

doubling option)

MX-RIX with Zone Analyser

8 fully programmable zones on

remote expander (16 using zone

doubling option)

Not Available

Maximum Zones Capacity

32 zones using zone doubling

option and zone expander

24 zones using doubling option and

zone expander

Zone Configurations

1. Normally closed

2. DEOL – 2 end of line resistors

3. Zone doubling – 1 end of line

resistor

1. Normally closed

2. DEOL – 2 end of line resistors

3. Zone doubling – 1 end of line

resistor

Zone Types

1. Entry / Exit

2. Access

3. Immediate

4. Medical

5. Arm

6. Omitted (Bypassed)

7. Fire

8. PA

9. 24hr

10. Key box

11. Shunt keypad

12. Tamper

13. Key switch Latched

14. Key switch Momentary

15. Unused

1. Entry / Exit

2. Access

3. Immediate

4. Medical

5. Arm

6. Omitted (Bypassed)

7. Fire

8. PA

9. 24hr

10. Key box

11. Shunt keypad

12. Tamper

13. Key switch Latched

14. Key switch Momentary

15. Unused

Zone Attributes

1. Chime

2. Test

3. Mask

4. Double knock

5. Normally Open

6. Normally Closed

1. Chime

2. Test

3. Mask

4. Double knock

5. Normally Open

6. Normally Closed

PROGRAMMABLE OUTPUTS

PGM On-Board

Outputs

1. PGM1 – N/O / N/C

2. PGM2 –

(832+) N/O / N/C

(832) Active High / Active Low

3. PGM3 – Active High / Active

Low

4. PGM4 – Active High / Active

Low

1. PGM1 – N/O / N/C

2. PGM2 – Active High / Active Low

3. PGM3 – Active High / Active Low

4. PGM4 – Active High / Active Low

NOTE: Active High switches from 0V to 12V; Active Low switches from 12V to 0V.

Matrix 832 / 832+ / 424

Page 6 RINS428-5

Matrix 832 / 832+ Matrix 424

PGM Options

1. Off

2. PIR remote LED enable (E-)

3. PIR Latch memory (C+)

4. Follow Arm / Disarm

5. Follow zone

6. Follow line fail

7. Follow kiss off

8. Shock / Fire reset

9. Follow strobe

10. Follow Fire Alarm

11. Follow PA

12. Confirmed Alarm

13. Follow Tamper Alarm

14. External Bell

15. GND Fire detector – PGM 4 only

16. Twin Alert – PGM 3 only

17. Follow entry exit

18. Follow Digi Com - Fire Signal

19. Follow Digi Com - PA Signal

20. Follow Digi Com - Intruder Signal

21. Follow Digi Com - Open/Close

22. Follow Digi Com - Spare Signal

23. Follow Digi Com - Medical Signal

24. Follow Digi Com - Conf Signal

25. Follow Digi Com - Omits Signal

26. Follow Hidden Display

27. Follow Mains Fail

28. Follow Battery Low

29. Follow Battery Missing

30. Internal Sounder

1. Off

2. PIR remote LED enable (E-)

3. PIR Latch memory (C+)

4. Follow Arm / Disarm

5. Follow zone

6. Follow line fail

7. Follow kiss off

8. Shock / Fire reset

9. Follow strobe

10. Follow Fire Alarm

11. Follow PA

12. Confirmed Alarm

13. Follow Tamper Alarm

14. External Bell

15. GND Fire detector – PGM 4 only

16. Twin Alert – PGM 3 only

17. Follow entry exit

18. Follow Digi Com - Fire Signal

19. Follow Digi Com - PA Signal

20. Follow Digi Com - Intruder Signal

21. Follow Digi Com - Open/Close

22. Follow Digi Com - Spare Signal

23. Follow Digi Com - Medical Signal

24. Follow Digi Com - Conf Signal

25. Follow Digi Com - Omits Signal

26. Follow Hidden Display

27. Follow Mains Fail

28. Follow Battery Low

29. Follow Battery Missing

30. Internal Sounder

PGM Expander MX-ROX

Outputs

1. 8 open collector – Installable

remotely on keypad bus

2. 8 relay expander – installable

remotely on keypad bus

1. 8 open collector – Installable

remotely on keypad bus

2. 8 relay expander – installable

remotely on keypad bus

KEYPADS

Type

1. Two 7 segments LED

2. LCD 32 character

3. ICON

1. Two 7 segments LED

2. LCD 32 character

3. ICON

Dedicated buttons

1. PA

2. Fire

3. Medical

1. PA

2. Fire

3. Medical

Max number

Four of same type (max 6 devices) Four of same type (max 6 devices)

Settings

1. Private - system status indicated

during arming

2. Public - system status indicated

in arm mode

3. Hidden - display suppressed after

20 seconds

1. Private - system status indicated

during arming

2. Public - system status indicated

in arm mode

3. Hidden - display suppressed after

20 seconds

LCD Keypad

Supply Voltage

9-16Vdc 9-16Vdc

Supply Current

80mA – Normal

20mA – Minimum brightness setting

80mA – Normal

20mA – Minimum brightness setting

LED Keypad

Supply Voltage

9-16Vdc 9-16Vdc

Supply Current

60mA Maximum @ 13.8V 60mA Maximum @ 13.8V

ICON Keypad

Supply Voltage

9-16Vdc 9-16Vdc

Supply Current

50mA Maximum @ 13.8V 50mA Maximum @ 13.8V

! Matrix 832 / 832+ / 424

RINS428-5 Page 7

Matrix 832 / 832+ Matrix 424

PROXIMITY READER (Not approved for use in Denmark, Norway, Finland or Sweden)

Type

Inductively coupled key-fob or card Inductively coupled key-fob or card

Max number

Four of same type (max 6 devices) Four of same type (max 6 devices)

Settings

1. Private – system status indicated

during arming

2. Public – system status indicated

in arm mode

1. Private – system status indicated

during arming

2. Public – system status indicated

in arm mode

Supply Voltage

9-16Vdc 9-16Vdc

Supply Current

Max [email protected] Max [email protected]

PARTITIONS

Number of partitions

4 true partitions with common option 4 true partitions with common option

Independent settings

1. Zones

2. Keypads

3. Proximity readers

4. User codes

5. PGMs

6. Timers

7. Reporting account codes

1. Zones

2. Keypads

3. Proximity readers

4. User codes

5. PGMs

6. Timers

7. Reporting account codes

Arm modes

4 arm modes per partition (A, B, C, D) 4 arm modes per partition (A, B, C, D)

Home / Away allocation

Programmable individual arm modes Programmable individual arm modes

Arming options

1. Final door

2. Timed exit

3. Silent arm

4. Forced Arm

1. Final door

2. Timed exit

3. Silent arm

4. Forced Arm

Timers

1. Entry / Exit

2. Bell Delay

3. AC Fault Delay

4. Telephone Line Fault Delay

5. Inactivity Arm Time 10-990min

6. Auto Arm – Time of Day

7. Final Exit Delay

8. Quartz Correction Factor

9. Confirmed Alarm

1. Entry / Exit

2. Bell Delay

3. AC Fault Delay

4. Telephone Line Fault Delay

5. Inactivity Arm Time 10-990min

6. Auto Arm – Time of Day

7. Final Exit Delay

8. Quartz Correction Factor

9. Confirmed Alarm

Real time clock

1. AC frequency Based

2. Quartz Based

1. AC Frequency Based

2. Quartz Based

USER CODES

Number of user codes

32 codes (4 to 6 digits) 32 codes (4 to 6 digits)

User code types

1. Master user per partition

2. Limited user

3. Duress

4. Engineer

5. Arm only - can be used as a

patrol code

6. Disarm only - can be used as a

patrol code

7. Omit (Bypass)

8. Temporary

9. Limited number of uses

1. Master user per partition

2. Limited user

3. Duress

4. Engineer

5. Arm only - can be used as a

patrol code

6. Disarm only - can be used as a

patrol code

7. Omit (Bypass)

8. Temporary

9. Limited number of uses

CENTRAL MONITORING OPTIONS

Telephone Numbers

9 telephone numbers shared with

pager, Pyronix PC format and digital

communication formats

9 telephone numbers shared with

pager, Pyronix PC format and digital

communication formats

Communication Protocols

1. Contact ID

2. Pager Format

3. BSIA Fast Format

4. Pyronix PC Format

5. MX Voice

1. Contact ID

2. Pager Format

3. BSIA Fast Format

4. Pyronix PC Format

5. MX Voice

Matrix 832 / 832+ / 424

Page 8 RINS428-5

CENTRAL MONITORING OPTIONS – Cont.

Group Reporting to CMS

1. Events sent to 1 number only

2. Events sent to 2 numbers

3. Events sent to first number with

backup of second number

1. Events sent to 1 number only

2. Events sent to 2 numbers

3. Events sent to first number with

backup of second number

Programmable Send

Options

1. In disarmed mode

2. In arm modes A, B, C and D

3. Restorals

4. Alarms

5. PAs

6. Fire

7. Maintenance

8. Open / Close

9. Medical

1. In disarmed mode

2. In arm modes A, B, C and D

3. Restorals

4. Alarms

5. PAs

6. Fire

7. Maintenance

8. Open / Close

9. Medical

Test Call

Programmable in days, hours and

minutes

Programmable in days, hours and

minutes

Telephone Line Monitoring

Yes – with status indication Yes – with status indication

Telephone Connection

Allows other telephone on the line Allows other telephone on the line

Digital Communicator

Analogue line Analogue line

Lightning Protection

Heavy duty lightning protection

6.75kV/125Amps

Heavy duty lightning protection

6.75kV/125Amps

OTHER

Software Support

1. UDL programming software

2. Pyronix MX-MON software to be

used with:

a. Modem + Pyronix format

b. RC12/RC112 +

Contact ID/BSIA

1. UDL programming software

2. Pyronix MX-MON software to be

used with:

a. Modem + Pyronix format

b. RC12/RC112 +

Contact ID/BSIA

Memory Event Log

300 events with time and date

Log deletion cannot be allowed either

accidentally or on purpose.

Log reaction time is more than 30

days and the clock will not change

more than + / - 10 mins over 1 year at

20c

300 events with time and date

Log deletion cannot be allowed either

accidentally or on purpose.

Log reaction time is more than 30

days and the clock will not change

more than + / - 10 mins over 1 year at

20c

1.3.1.1 Minimum Installation Requirements

In addition to the main alarm panel (424, 832 or 832+), and any detectors or sensors, at least one keypad is

required. This can be an LCD, LED or ICON keypad. One keypad MUST be set to ID-1. This is the minimum

requirement.

1.3.1.2 Installation Constraints

A maximum of 6 devices can be attached to the Matrix bus (see also Section 4: Cabling Rules for the Matrix

Bus). The following table shows the maximum number of each device type allowable, whilst at the same time

remembering that only 6 devices in total can be on the bus at any one time.

BUS DEVICE MATRIX 832+ /832 MATRIX 424

LCD Keypad 4 4

ICON Keypad 4 4

MX-PROX Proximity Reader 4 4

MX-RIX with Zone Analyser 1 1

On-board Input Expander 1 1

MX-ROX Output Expander 1 1

! Matrix 832 / 832+ / 424

RINS428-5 Page 9

Section 2: Safety & Approvals

SAFETY

1. A technically competent person must carry out the mains installation in accordance with the national and

local electrical installation regulations

2. Protective Earth: This equipment must be earthed/grounded

3. Functional Earth: Must be connected to earth terminal to allow the equipment to operate correctly. Has

no safety implications.

4. Connect the unit to a single pole, unswitched, 3 Amp fused spur, using 0.75mm

2

cable. If the Neutral

cannot be positively identified use a double pole disconnect version.

5. Always remove / isolate the mains supply before carrying out any servicing of the panel.

6. Fuses: For continued protection against the risk of fire, replace only with the same type and rating of

fuse.

7. There are no user serviceable parts inside the equipment.

8. This unit should be mounted so that there will be no outside access to the electrical cable entry point

9. Ventilation: To ensure the correct airflow, always mount the unit vertically with the unit having a clear

space on all sides. It must not be covered by clothes, furnishings, boxes, etc. It must not be mounted

close to, or above, heat radiating sources.

10. On completion of wiring, use tie-wraps to prevent any loose wires causing a safety hazard.

11. The mechanical mounting of the unit must be secure enough to carry the full weight of the unit including

all batteries.

12. Batteries: Ensure that the battery terminal connections will not create an electrical short-circuit on the

case metalwork when the unit is closed. Use insulated battery lead connectors.

13. Dispose of old batteries as required by environmental legislation / recommendations.

14. The battery case must have a flame-retardant rating of UL94-V2/V1/V0 – IEC60950:2000

15. Water: The equipment must be kept free from dampness, water and any other liquids. It is only suitable

for installation indoors.

ICONS

Protective Earth

Must be connected to the electrical installation earth / ground

Protective Bonding

Must be connected to the equipment protective earth terminal

Functional Earth

Must be connected to earth terminal to allow the equipment

to operate correctly. Has no safety implications.

Read

Read equipment instructions

C

O

M

P

L

I

A

N

C

E

Matrix 832 / 832+ / 424

Page 10 RINS428-5

! Matrix 832 / 832+ / 424

RINS428-5 Page 11

Matrix 832 / 832+ / 424

Page 12 RINS428-5

The maximum voltage applied to the equipment must not exceed the safety extra low voltage SELV limits

specified in IEC60950 / EN60950 / UL60950 30VDC / 30VAC / 42.4Vpeak

If you need to switch greater voltage, current or power you will require the use of a separate external

switching relay

! Matrix 832 / 832+ / 424

RINS428-5 Page 13

PYRONIX Ltd

Pyronix House

Braithwell Way

Hellaby,

Rotherham

South Yorkshire

S66 8QY

HTTP://www.pyronix.com ENGLAND, UK

______________________________________________________________

EU Declaration of Conformity

EN45014

Manufacturer: As above

Details of electrical equipment

Model name(s) Matrix 832+ (Plastic & Metal Housing)

MX-ROX8T, MX-ROX8R, MX-RIX with Zone Analyser

LCD, LED, Icon keypads, MX-PROX

Description: Control & Indicating Equipment

Remote expanders, keypads

Directives that this equipment RTTE 99/05/EC

complies with:

Harmonised Standards applied EN50081-1: 1992 Class B

in order to verify compliance EN50130-4: 1995 + A1: 1998

with the Directives: EN301489-1: V1.4.1

EN301489-3: V1.3.1

EN300330-2: V1.1.1

Testing Agency Status ISO/IEC17025 Certificate No Cert.

Date

Pyronix Matrix Series Guida d'installazione

Questo manuale è adatto anche per

Pyronix Matrix Series Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti