SEA Unigate FV Manuale utente

R

Automatic Gate Openers

Rev. 03 - 03/2019cod. 67412090

Unigate FV

SEA S.p.A.

Zona industriale 64020 S.ATTO Teramo - (ITALY)

Tel. +39 0861 588341 r.a. Fax +39 0861 588344

www.seateam.com [email protected]

ENGLISH

FRANÇAIS

ESPAÑOL

ITALIANO

1

Control unit power supply: 230 Vac 50/60 Hz - 115Vac 50/60 Hz

Absorption in stand by: 30 mA

Environment temperature: -20°C +50°C

Specications of external box: 325,7 X 246 X 140

COMPONENTS

CN1 = Input/output connectors

CN2 = Limit switch, 24V~, Electric lock connector

CN3 = Encoder terminal board/PositionGate/gp1/gp2

Jolly/Cloud connector Jolly 3 or Sea Cloud

FIX = FIX receiver plug in connector

CR1 = Relay 1 clean contact terminal

CR2 = Relay 2 clean contact terminal

2PM = 2PM module power supply connector

CNB = Batterie charger connector

CNP = Programming connector

CLS = Limit switch quick connector

Power - + = Power supply switching connector

Module 1 = Motor 1FV module/2PM module connector

Module 2 = Motor 2 FV module

Master/Slave = Mater/Slave card connector

Progr = Programming connector through Open

Exp = SEM 2 external module connector

CNR = UNI receiver connector

Battery = Back up battery CR 2032

MEM = Radio trans. memo for FIX receivers

ENGLISH

2

MENU

SEA

SET

To reactivate an NC contact, follow this procedure:

Go to and press OK for 5 seconds, then enter the INPUT CHECK MENU and

check the operating status of all inputs

CONNECTIONS

No need to repeat self programming after reactivation of N.C. contacts.

The herein reported functions are available starting from revision 00.14

Warning: Automatic detection of not used N.C. inputs (Photocells, Stop, Limit switch and Edges)

ENGLISH

V 00.14 or

subsequent

COM (-)

1

CN1

2 3 4 5 6 7 8 9 10 11 12 13

CR1 CR2

CNF

2212029181716141 51

23

CN3

Master/Slave

Progr

54001590

UNIGATE DG

MEM

Display

Battery

Exp

Radio Module

Jolly/Cloud

FIXFIX

UP Down OK

24V

LSC1

LSC01

COM

Module1

Module2

Power 2 PM

Power Battery charger

COM

5V 24V

COM

COM1 NO1 NC1 COM2 NO2 NC2

-+ -S +

24 25 26 27 28 29 30

COM2 NO2 NC2

COM

COM1 NO1 NC1

24VDC

24VAC

FL -

+PG positive Position Gate

E1D1 Position gate data 1/

Encoder 1

E2D2 Position gate data 2/

Encoder 2

GP1 input

GP2 input

(+ encoder)

24V (1A max)

Closed limit switch

M2

Opened limit switch

M2

Comune

Closed limit switch

M1

Opened limit switch

M1

Electro lock

Clean contact

24V (1A max)

COMIS

(common accessories)

Antenna

Common

Start

Start Pedestrian

Stop

Common

Loop 1- Photocell 1

Loop 2- Photocell 2

Security edge 1

Security edge 2

Common

aux Programmabile

(24 VDC --- 1A max)

Flash Light

(500 mA max)

11

USB

UNIGATE CONNECTION WITH AN INVERTER MODULE

It is mandatory to connect the ground cable to the PE input

L : phase

N: neutral

PE: ground

L : phase

N: neutral

PE: ground

UNIGATE CONNECTION WITH TWO INVERTER MODULES

ENGLISH

CN1

Inverter power supply

230 115 Vac

CN1

Inverter power supply

terminal

230 115 Vac

CN1

Inverter power supply

terminal

230 115 Vac

CN2

Dry contact and

motor output

CN2

Dry contact and

motor output

CN2

Dry contact and

motor output

4

INIT

MENU

SEA

SET

PARAMETER AND NO/NC CONTACTS PRE-CONFIGURATION

1)

2)

Power OFF

3)

Keep pressed the two buttons UP and DOWN and, at the same time, connect the power supply

cable for initialization of the control unit INIT appears on the display or go to menu 14: RESET

- When N.C.

(Photo, Stop, Limit

switch and Edge)

- When N.O.

(Start, pedestrian

start)

4)

All parameters return to default conguration, see column “Default” in the table of the

menus and all the inputs will show their real status

When the photocell

is crossed or input is

engaged

When input is not

engaged

When not engaged or

not wired

N.C. contacts

N.O. contacts

When input is engaged

.

5)

All NC contacts are automatically switched off if not used (no segments on display).

If the contacts are connected, they will be On on the display (segment switched on).

To reactivate the NC contacts it is necessary to enter each menu which shows the NC contacts

(e.g.: STOP, PHOTO, EDGE, LIMIT SWITCH....) and with SET put them on ON.

ENGLISH

Start

Photocell 1 Edge 1 Edge 2

Photocell 2

Pedestrian

opening

DISPLAY INPUTS STATUS

Stop

MENU

SEA

SET

- - -

- - - -

Limit switch

opening motor 1

Limit switch

closing motor 1

Limit switch opening motor 2

(or slow opening BIG FAST)

Limit switch closing motor 2

(or slow closing BIG FAST)

5

QUICK START AND PROGRAMMING

Default (ON) = Single leaf

CHOOSE BETWEEN SINGLE OR DOUBLE LEAF

ATTENTION: This procedure is potentially dangerous and must only be performed by specialized

personnel

PRESET INSTALLATION

ENGLISH

1

2

3

A

B C

D E

MENU MENU

MENU

SEA SEA

SEA

LANGUAGE

English

START

Skip this step if you don’t want to programm a transmitter

Skip this step if you are working in sliding or single leaf mode

PRESS

BUTTON

STORED

Trasmitters

MOTOR

SINGLE

LEAF

RECEIVER

MISSING

UP

OK

Press the

button of

the TX to be

stored

Press

another

button or

another TX

to be store it

Choose the type

of motor with UP

or DOWN

With UP or DOWN choose

ON only if in single leaf mode

(motor 1)

Turn OFF the power

Put the power ON

Release the operators Manually push the leaves in half position

Reset the mechanical lock

If on the

display

appears

the item:

check if a

receiver

has been

connected

RX

Connector CNA

To conrm and

return to the

main menù

To conrm and

return to the

main menù

To exit

SET SET

SET

Remote control programming

After programming connect the antenna

Example

Release

6

M1

M2

P1

M1 M2P1

2 MOTORS MANUAL SELFLEARNING

A) WITH IMPULSES *

The gate will start the following cycle: M2 CLOSING - M1 CLOSING - M1 OPENING - M2 OPENING

- M2 CLOSING - M1 CLOSING. To store the respective stops during cycle, press UP or DOWN or

START on each mechanical stop point of the leaf. Self-learning has been completed. In the case of

a single leaf the cycle will be CLOSING 1 - OPENING 1 - CLOSING 1.

ENGLISH

Press UP or TX, if stored, when

M2 is closed position.

M2 in closing

M1 in closing

M1 in opening

M2 in opening

M2 closed

M1 closed

M1 open

M2 open

Both doors halfway

Press UP or TX, if

stored, when M1 is

closed position.

Press UP or TX, if

stored, when M1 is in

closed position.

Press UP or TX, if

stored, when M2 is in

closed position.

Press UP or TX, if

stored, when M1 is

open position.

Press UP or TX, if

stored, when M2 is in

open position.

9

PROGRAMMING

OK

MENU MENU

SEA SEA

SET SET

OK

A

F

M

B

G

N

C

H

O

D

I

E

L

7

Make sure that, for all types of self-learning, the gate performs the following cycle: M2 CLOSING,

M1 CLOSING, M1 OPENING, M2 OPENING, M2 CLOSING, M1 CLOSING. Otherwise, see the

MOTOR REVERS function.

The cycle in case of single leaf will be CLOSE MOTOR 1 - OPEN MOTOR 1 - CLOSE MOTOR 1.

Note: to adjust sensitivity on obstacle refer to the special menu

SELF-LEARNING starts AUTOMATICALLY.

Now it is necessary to wait until the leaf or leaves rst start closing and then automatically complete

the CLOSING - OPENING - CLOSING cycle.

When an Encoder is installed, it is necessary to select ON in the 32-ENCODER menu

B) ENCODER *

When the potentiometer is installed, it is necessary to select

SELF-LEARNING starts AUTOMATICALLY

The potentiometer threshold intervention is set automatically during self-learning

IT IS NOT NECESSARY TO ADJUST THE MENU FROM

Note: to adjust sensitivity on obstacle refer to the special menu

ENGLISH

AUTOMATIC SELF-LEARNING 2 MOTORS

C) POTENTIOMETER *

MENU

SEA

SEA SEA

SEA

32 - encoder

33

opening sensitivity

motor 1

38 pot.

from threshold

to opening 1

37

slowdown

sensitivity

45 pot. slowdown

threshold closing 2

9

programming

9

programming

ON

potentiomer

ON

OK

SET

Now it is necessary to wait until the leaf or leaves start before closing and automatically complete

the cycle CLOSING - OPENING - CLOSING - OPENING with slowdown - CLOSING with slowdown

Note 2: With the potentiometer you can also make the self-learning giving impulses on favourite

opening or closing points; In this case it is also possible to modify the parameters I.AP.M1, I.CH. 1,

I.AP.M2, I.CH.M2 of + 100 impulses, if you need to optimize the initial and the nal position

Nota 3: In the case of MIXED PROCEDURE (AUTOMATIC stop detection in closing and with

MANUAL input in opening) the learning cycle will only be CLOSE-OPEN-CLOSE.

8

*REVERSE MOTOR

If the motor starts in opening, turn power off and on again, select “5 - REVERSE MOTOR” on the

display through UP and DOWN press OK and put on ON, or, if you have the Jolly 3 programmer,

activate the motor exchange function.

D) AMPEROMETRIC* (For electromechanical motors only)

This type of selearning is possible ONLY for electromechanical operators and physical stops.

Note: to adjust sensitivity on obstacle refer to the special menu

E) WITH LIMIT-SWITCHES*

1 - LIMIT SWITCH INPUT CHECK: check each limit switch on both doors by activating them before

self-learning. The segment on the display will disappear when each limit switch is activated

SELF-LEARNING starts AUTOMATICALLY

ENGLISH

MENU MENU

SEA

3 MOTOR MECHANIC

OK

SET

MENU

MENU MENU

MENU

SEA

SEA SEA

SEA

9

PROGRAMMING

9

PROGRAMMING

ON

OK

SET

At this point it is necessary to wait until the leaf or leaves start before closing and automatically

complete the CLOSING - OPENING - CLOSING cycle.

At this point it is necessary to wait until the leaf or leaves rst start closing and then automatically

complete the CLOSING - OPENING - CLOSING cycle.

9

OPERATING FUNCTIONS

ONLY AFTER THE SELF LEARNING OF WORKING TIMES WITH AUTOMATIC LOGIC, IT will BE

POSSIBLE TO CHANGE LOGICS INTO TO:

A) AUTOMATIC

A start impulse opens the gate. A second impluse during the opening will not be accepted.

A start impulse during closing reverses the movement.

NOTE 1: For automatic closing it is necessary to set a pause time, otherwise all the logics will be

semi-automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU

the item 8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

B) SECURITY

A start impulse opens the gate. A second impulse during opening reverses the movement.

A start impulse during closing reverses the movement.

NOTE 1: For automatic closing it is necessary to set a pause time, otherwise all the logics will be

semi-automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU

the item 8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

C) STEP BY STEP TYPE 1

The start impulse follows the OPEN-STOP-CLOSE-STOP-OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic

will be semi-automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU

the item 8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

ENGLISH

MENU

SEA

7

Pause time

more than 0 sec

SET

MENU

SEA

7

Pause time

more than 0 sec

SET

MENU

SEA

7

Pause time

8

start in pause

8

start in pause

8

start in pause

ON (accepts the start)

OFF (doesn’t accepts the start)

SET

6

MENU

SEA

Skip this step if you work in semi-automatic logic

Logic

OK OK

Choose the desired logic with

UP or DOWN

To conrm and return

to the main menu

SET

10

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU

the item 8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

E) DEAD MAN

The gate opens as long as the START button of opening is pressed; releasing it the gate stops. The

gate closes as long as the button connected to the PEDESTRIAN START is pressed; releasing it

the gate stops. To execute complete opening and/or closing cycles the related pushbuttons must

be constantly pressed.

F) 2 BUTTONS

One start opens, one pedestrian start closes. In opening the closing will not be accepted. In closing

a start reopens, a pedestrian start (close) will be ignored.

D) STEP BY STEP TYPE 2

The start impulse follows the OPEN-STOP-CLOSE -OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic

will be semi-automatic.

ENGLISH

MENU

SEA

8

start in pause

ON (accepts the start)

OFF (doesn’t accepts the start)

SET

more than 0 sec

MENU

7

Pause time

SET

SEA

11

RADIO TRANSMITTER SELF LEARNING WITH

UNI RECEIVER ON BOARD OF CONTROL UNIT

WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver

into the special CMR connector (if available) with control unit turned off. With RF UNI and RF UNI PG module

it will be possible to use both Coccinella Roll Plus transmitters and radio transmitters with xed code. The rst

memorized radio transmitter will determine the type of the remaining radio transmitters. If the receiver is a

Rolling Code, press the button of the radio transmitter that you want to program twice to memorize the rst TX.

In the case of transmitters with xed code it is necessary to press 1 time the button of the transmitter you want

to program to store the rst remote control.

Notes:

- Perform the radio transmitters learning only with stopped cycle and closed gate.

- You can store max. 2 of the available 4 functions. If the control unit receives a code that has already been

assigned to another function it will be updated with the new function.

ENGLISH

RF UNI

RF UNI PG

old model

RF UNI PG

new model

16 users without memory

800 users with additional memory MEM

100 users xed code

800 users roll plus

100 users xed code

800 users roll plus

2

1

TX button

Memory location

4

serial

number

customer

1

0

2

3

MENU MENU MENU

MENU MENU

MENU

MENU MENU

MENU

SEA SEA SEA

SEA SEA

SEA

SEA SEA

SEA

START

press button

stored

0

OK

ok? ok

Pedestrian

start

External

module

STOP

RELAY

Bistable

Stop

Delete a TX

Move on EEP

Clear memory

SET SET SET

SET SET

SET

SET SET

SET

SET SET

SET

UP

OK

Conrm the cancellation

Press the

button of the

transmitter to

be stored

If you want to

program the

pedestrian start as

second channel

Press the

button of the

transmitter to

be stored

If you want to

program the

activation of the light

output as second

channel

Press the

button of the

transmitter to

be stored

If you want to

program the stop as

second channel

Press the

button of the

transmitter to

be stored

If you want to

program the second

channel to activate

relay CR1 or CR2

Press the

button of the

transmitter to

be stored

If you want to

program the stop as

bistale stop

Press the

button of the

transmitter to

be stored

Press the

button of the

transmitter to

be stored

If you want to delete

a single transmitter

Select with UP

and DOWN

the memory

location to be

selected and

press OK

Move the TX FIX’s

the extractable

memory (MEM)

If you want to delete

the whole memory

If you do not want to cancel , press UP or DOWN to

return to the 2 transmitters menu

Menu output

OK

for 10 sec

MENU

Release

END

SET

If you want to

program a button as

electric brake release

12

ATTENTION: Program the radio controls before connecting the antenna and inserting the receiver

into the appropriate CNS connector (if available) with the FIX RF module it will be possible to use

only xed code radio transmitter. Select the 2-TRANSMITTERS on the display and press OK, at

this point using the UP and DOWN buttons, select the command to associate the button (maximum

2 commands can be associated) and press OK to conrm the choice, now press the button of the

radio transmitter that you want to associate. If the memorization has been successful, the message

“Memorized” will appear on the display.

In MENU 2-TRANSMITTERS MENU it is possible to select the items: “Start” (to associate a Start

command), “Pedestrian Start” (to associate a Pedestrian Start command), “Stop” (To associate a

STOP command to the TX ), “Delete memory” (To delete all the TXs), “Delete one TX” (To delete the

single TX but if it is a Rolling Code Plus transmitter), “Release” (to associate the TX with the electric

brake release). To release the electric brake it is necessary to give 3 consecutive impulses, the 4th

impulse will reactivate the electric brake lock.

Note:

- Perform radio control learning only with control unit switched off and closed the gate.

- It will be possible to memorize up to a maximum of 16 codes (buttons), by adding the MEM

memory it will be possible to memorize up to 496 different codes.

- It is possible to memorize up to 2 of the 4 functions available. If a code is received that had already

been assigned to a function it will be updated with the new function.

DELETING THE TX FROM THE RECEIVER

With FIX RF modules, it will be possible to delete only the entire RX memory. Proceed as follows:

select the “Clear memory” in the 2-TRANSMITTERS menu and keep the OK button pressed until

“OK” appears on the display.

Connect the receiver to the CNS

connectors, respecting the direction

in the gure .

RADIO CONTROL SELF-LEARNING WITH FIX RECEIVER

ON BOARD

ENGLISH

13

Enter the menu and press the button OK for 5 seconds, you can enter the CHECK MENU,

where it is possible to check the operating status of all inputs.

Note: If the Stop, Photocell 1 and Photocell 2, Edge 1 and Enge 2 contacts are not bridged in

selearning, they will be deactivated and can be reactivated through this menu, without repeating

times selearning.

INPUTS CONTROL MENU

Language

MENU

SEA

SET

LIMIT SWITCH

CLOSING 1

LIMIT SWITCH

OPENING 1

EDGE

1

EDGE

2

PHOTO

1

PHOTO

2

END

LIMIT SWITCH

CLOSING 2

0.0 V

voltage level

on the

batteries

This item indicates the battery charge level

LIMIT SWITCH

OPENING 2

PARTIAL

OPENING

Enabled

Blocked

START

STOP

START

MENU

OK

MENU FUNCTION TABLE

To access the Menu for input check keep pressed OK for about 5 seconds.

Description

Exit menu

Start

Test

Stop

Test

Partial

Opening

Test

Safety

edge1

test

Safety

edge2

test

Photocell 1

test

Photocell 2

test

M1 Opening

limit switch

test

M1 Closing

limit switch

test

M2 Opening

limit switch

test

M2 Closing

limit switch

test

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works. If SET is

always on, make sure that the contact is a N.C. contact or that the

related limit switch is not occupied.

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works. If SET is

always on, make sure that the contact is a N.C. Contact or that the

related limit switch is not occupied.

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works. If SET is

always on, make sure that the contact is a N.C. contact or that the

related limit switch is not occupied.

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works. If SET is

always on, make sure that the contact is a N.C. Contact or that the

related limit switch is not occupied.

The contact must be a N.O. Contact . When activating the related

command on the display SET lights up, the input works.

If SET is always on, check the wirings.

The contact must be a N.C. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.O. Contact. When activating the related

command on the display SET lights up, the input works.

If SET is always on, check the wirings.

ENGLISH

control

14

MENU

SEA

94 24V AUX

SET

PHOTOCELL AND ANTENNA CONNECTIONS

A) 24V DC 11 and 12

PHOTOCELL 1 AND PHOTOCELL 2 (LOOP1 - LOOP2)

11 and 12 aux ~ (Accessories) 1A max COM = 0V

7 PH1 = Photocell contact 1

8 PH2 = Photocell contact 2

Default settings:

PHOTO 1 = “Close” - PHOTO 2 = “Open”

Photocell 2 can also be set as TIMER (see below TIMER function). For photocell options, see menu

97 and 98.

TIMER: holding PH2 pressed, the gate opens and remains open, while, when released, the gate

repeats the selected pause time and starts closing. If a safety device is activated, the Timer resets

automatically after 6 sec.

AUTOTEST function: make sure that the photocells are fully functional before any movement. If the

test fails, it will be indicated on the display.

To activate the AUTOTEST:

1) Connect the TX photocell power supply to the aux 12 inputs

2) Enter the 95-FOTOTEST menu and select on which accessory (Photocell 1 or Photocell 2 or

both) to activate this mode.

If you want to monitor the absorption of accessories, connect them to the inputs 20 of CN2 (COMIS)

max 350mA

B) CONFIGURATION 24V DC AUX CN1 12 CONFIGURATION

On the 24V AUX you can select when and how to operate the connected auxiliary accessory.

See menu 94-24V AUX.

The 94-24V AUX menu options are:

(See special menu)

• Always

• In cycle

• Opening

• Closing

• In pause

• Self-test

• In cycle and phototest

• In cycle and pause

• Indicator light gate open

ENGLISH

15

MENU

SEA

SET

10K PHOTOCELL (SINGLE OR DOUBLE) 7 and 11 - 8 and 11

On the clamps 7 and 11 - 8 and 11 of the CN1 it is also possible to connect a 10K Photocell.

On menu 121 type photo 1 and on the menu 122 type photo 2, it will work according to the settings

given from menu 97-PHOTO 1 and 98 Photo 2.

Note1: Using the 10K Photocell, further protection will be provided also in the event of a short-circuit

on the cables.

Setting 10 K Photocell

121 PHOTO 1

TYPE

SAFETY EDGE 9 and 11 - 10 and 11

It is possible to connect a safety edge between the contacts 9 and 11 of CN1 (or two edges, with the

second one connected between the contacts 10 and 11) . When pressed, the Safety Edge opens

the contact causing a partial inversion of the movement both in opening and in closing. The Safety

Edge input can be set «only in closing», «only in opening» or both.

Note1: Through the on-board display or the JOLLY 3 programmer it is possible to activate the

balanced edge 8K2, in this case the edge contact is controlled by a special resistance value

revealing the eventual involuntary short- circuit of the device. In the case of imbalance of the device

a special alarm will be shown on the on-board display or on the JOLLY programmer.

It is also possible to set two 8K2 Safety Edges on each single input Safety Edge.

Note2: Self-test can be made also on a powered radio Edge (See Auto-test Menu)

Latch open / latch close function

Inputs 10 and 11 can be set accordingly as latch open and latch close - see menu 118.

UP

OK

MENU

SEA SEA

OFF Photo 10K

SET SET

ENGLISH

16

PEDESTRIAN START - STOP - START - CONNECTIONS

PEDESTRIAN START (N.O.) 4

Function 1 (STANDARD): partial opening space adjustable from 5 to 100 (90-OPENING menu)

Function 2 (TIMER): by holding the pedestrian (4) the gate opens and remains open. Releasing it

the gate repeats the selected pause and starts closing. In the case of a safety device activation the

timer will automatically reset after 6 sec.

Function 3 (2 BUTTONS): in 2 buttons logic press the pedestrian Start (4) to close the gate.

Function 4 (DEADMAN): in deadman logic this button executes the re-closing if you keep it pressed.

STOP (N.C.) 5

When pressing this button the motor immediately stops in any condition/position. To re-start the

movement give a start command. After a stop the motor always re-starts in closing.

START (N.O.) 3

Function 1 (STANDARD): an impulse given to this contact opens and closes the automation

depending on the selected logic.

Function 2 (TIMER): holding START starts the TIMER function, releasing the start, the operator

repeats the pause and then re closes. To connect other devices (e.g. the loop) refer to the related

instructions leaets (ie. loop detectors and proximity Switches). In the case of activation of a safety

device the timer will automatically reset after 6 seconds.

Function 3 (2 BUTTONS): in 2 buttons logic this button performs the opening.

Function 4 (DEADMAN): in deadman logic keep pressed the Start for the opening of the automation.

ENGLISH

17

24V FLASHING LAMP 3W MAX 12 and 13

24V 3W Max Flashing Lamp (Control lamp)

The 24V Flashing Lamp is connected between the connectors 12 (24VDC AUX) and FLS (-) of CN

1.

The Flashing lamp advises that the automatic gate is moving with 1 ash/second in opening and

2 ashes / second in closing. During pause it remains switched on. Through the warning lamp it is

also possible to identify alarms lied to the STOP, PHOTOCELL 1, PHOTOCELL 2 and EDGE 1 and

EDGE 2 devices. Through the display or the JOLLY 3 programmer it is possible to activate the pre-

ashing function and/or to modify the function of the ashing lamp choosing between x ashing

or control lamp. The preashing can be timed from 0 to 5 seconds otherwise it is possible to set it

before closing only.

FLASHING LAMP- BUZZER

BUZZER (24V ) AUDIBLE ALARM

IMPORTANT NOTE: INSTEAD OF THE FLASHING LAMP, YOU CAN ALSO CONNECT A BUZZER

IN THIS CASE SET THE 86-MENU ON «BUZZER»

Use an autoswinging buzzer 24V of 100 dB. The buzzer will be activated after two consecutive

activations of the entrapment protection. To reset the alarm it is necessary to push the STOP button.

Anyway after 5 minutes the buzzer will stop to sound and the automation stands still waiting for

commands.

If Buzzer does not work, check if the 86-FLASHING LIGHT menu is set on “Buzzer”

ENGLISH

LED LAMP 3W

BUZZER

18

COM

LSO1

LSC1

24V

21 22

LIMIT SWITCH CONNECTIONS

LIMIT SWITCH 14 15 16 17 18

Does not need a jumper when not connected.

For the limit switch function, limit switches must be installed, both in opening and closing. In the

case of single-leaf connect motor 1 (it is not necessary to bridge the limit switches of motor 2).

Anti-intrusion function can be activated. This function needs at least one limit switch, which pushes

the motor in closing direction once it’s released.

ELECTRIC LOCK OUTPUT 21 22

A 12V=15W max electric lock can be connected

The electric lock can be deactivated when not used for energy saving on the control unit.

The electric lock release can be timed from 0 to 5 seconds

The electric lock can be set: only before opening, only before closing or in both directions.

MAGLOCK CONNECTIONS

NOTA:

set the negative electric brake function in menu 132.

For the correct functioning of the limit switches there must be a correspondence between the

direction of movement of the motors and the respective engaged limit switches.

Quick connector

sliding limit switch

CLS

Note:

on some motors, the opening and closing limit-switch inputs 2 are used as a slow-down limit switch.

See BIG FAST Joint.

ENGLISH

19

POSITION GATE CONNECTIONS

The position gate allows to know the

exact position of the gate and to have

the reverse on the obstacle. The position

gate is applicable on the hydraulic

motors Half Tank and Mini Tank new

series, in combination with the LE card.

Note:

for distances of more than 2 meters, it is recommended to connect a shielded cable with a sheath

connected to COM 25

If the reading of the potentiometer is reversed compared to the movement of the motor, on the

display will appear the alarm “Potentiometer direction” and you will have to reverse the brown wire

with the green one and repeat programming.

AMPEROMETRIC DEVICE FOR ELECTROMECHANICAL OPERATORS

(active on Surf motor IV)

This control unit comes with an obstacle detection system working only on electromechanical

operators allowing to have the reversing on obstacles and the automatic detection of the stops.

Sensitivity adjustable from OFF to 99% in the special menu. The more the percentage is high the

more the obstacle detection will be difcult. On hydraulic unit this parameter will be always OFF.

Adjustable sensitivity intervention threshold. See menus 33 to 45.

The sensitivity on the obstacle is adjustable from 0 - 99%. The higher the percentage, the more

difcult it will be to detect the obstacle.

ENCODER CONNECTIONS

The encoder allows to know

the position of the gate and

to have the inversion on the

obstacle. To use the encoder

it is necessary to activate it in

the appropriate “32 encoder

on” menu. The sensitivity on

the obstacle is adjustable from

0 - 99%.

The higher the percentage, the

more difcult it will be to detect

the obstacle

To use the position gate, activate it in the

32 encoder menu: potentiometer

ENGLISH

20

La pagina sta caricando ...

SEA Unigate FV Manuale utente

SEA Unigate FV Manuale utente

in altre lingue

Documenti correlati

Altri documenti