SEA Gate 1 DG R2BF Manuale del proprietario

Marca: SEA

Modello: Gate 1 DG R2BF

Tipo: Manuale del proprietario

GATE 1 DG R2BF

With inverter module

Rev.05 - 06/2016

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

67411665

English

CONTROL UNIT FOR SLIDING GATES

(Cod. 23001235)

CN1 = Input/output connectors

CN2 = Courtesy light connector

CN3 = Power connector

CN4 = 24V~ connector

CN5 = Inverter control connector

CN6 = Limit switch connectors

CNA = Receiver connector RX

CNP = Programming connector

CNS = RF FIX Receiver connector

EXP = Expansion module connector -

LSE card

JOLLY 3 = Jolly 3 connector

DS = Programming display

CMS = Inverter interface connector

OK = Programming button

DOWN = Programming button

UP = Programming button

R1 = Relay C motor command Courtesy light

F1 = 6.3AT fuse on 230V

F2 = Accessories 1A fuse

Tr1 = Power transformer

GATE 1 DG R2BF

INVERTER

CN2CN3

Tr1

JOLLY3

CN6

CN1

CMS

CN5

CN4

CNA

EXP

UP DOWN OK

CNP

COMPONENTS

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

CNS

RECEIVER RX

155 mm

85 mm

JOLLY 3

TECHNICAL SPECIFICATIONS

Control unit power supply: 230 Vac Single-phase

Absorption in stand by: 30 mA

Environment temperature : -20°C +50°C

Specifications of external enclosure: 183 X 238 X 120 - IP55

SIGB

COM

SIGA

INTERFACE CARD

JUMPERS

WARNING: The control unit is designed with the automatic detection of not used N.C. inputs (Photocells, Stop and Limit

switch) except the SAFETY EDGE input. The exclude inputs in self-programming can be restored in the “Check inputs”

menu without need to repeat the programming (page 11).

The herein reported

f u n c t i o n s a r e

available starting

from: revision 01.07

c o m p a t i b l e w i t h

JOLLY 3.

3 4

5 6

7 8

CN1

Start

Stop

Common

Antenna

START Pedestrian

Common

Photocell 1

Common

ANT COM START

PEDST

STOP COM PH1 PH2

EDGE

24VAUX

COM 24V(FL) (FL)-

Safety edge 1

Flash (-)

+ +

- -

AUX Programmable

(24V 500 mA max)

24V 500 mA max

(Accessories)

3 4

5 6

7 8

CN1

Photocell 2

Start

Stop

Common

Antenna

START Pedestrian

Common

Photocell 1

Common

ANT COM START

PEDST

STOP COM PH1 PH2

EDGE

24VAUX

COM 24V(FL) (FL)-

Safety edge 1

Flash (-)

+ +

- -

24V 500 mA max

(Accessories)

Photocell 2

Optional

Obligatory jumper

without accessory

connection.

24Vac

Max 150 mA

CN4

LIMIT SWITCH

CN6

CN7

Limit switch Opening 1 (Green)

Limit switch Closing 1 (Yellow)

24V (Red)

Common (White)

Limit switch Opening 1 (Green)

Limit switch Closing 1 (Yellow)

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

16 17

18 19

CN2

Nota: The connectors

CN6 and CN7 are not

used if the Four limit

switch interface card is

connected.

CONNECTIONS

RADIO MODULE RF FIX

(CNS)

RF FIX

Receiver

connector

(Available from

hardware

revision R2)

Flash Light

Flash N

AUX Programmable

(24V 500 mA max)

GATE 1 DG R2BF

INVERTER

QUICK START

PROGRAMMING

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

UPDOWN

ALL OTHER PARAMETERS HAVE DEFAULT SETTINGS WHICH ARE USEFUL FOR THE 90% OF

THE APPLICATIONS BUT CAN BE HOWEVER SET THROUGH THE SPECIAL MENU. FOR

ENTERING INTO THE SPECIAL MENU MOVE ON ONE OF THE MENU AND PRESS THE UP

AND DOWN BUTTONS AT THE SAME TIME FOR 5 S.

PROGRAMMING

BUTTONS

DOWNUP

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

PRESS

BUTTON

STORED

TRANSMITTERS

START

MOTOR

SEA

SET

SEA

SET

LANGUAGE

ITALIANO

Skip this step if you do not want to program a transmitter

Press the

button of the

TX to be

stored

OK to exit

Menu or press

the button of

the next TX to

be stored

Choose the type of

motor with

UP or DOWN

To confirm and return

to main menu

SEA

SET

RECEIVER

MISSING

If on the display

appears the item:

Check if a receiver has

been connceted

(see page 2)

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

OK OK

LOGIC

PAUSE TIME

START IN

PAUSE

PROGRAM-

MING

TEST START

With UP or DOWN

choose

the desired logic

To confirm and return

to main menu

With UP or DOWN

choose a delay for

automatic closing

To confirm and return

to main menu

Skip this step

if you want to work

in half-automatic

logic

With UP or DOWN

Choose ON

To confirm and return

to main menu

With UP or DOWN choose ON

to start times learning

At the end of the selflearning

the control unit returns automatically

to the main menu

With

UP or DOWN Choose

ON to start test

To confirm and return to

main menu

Skip this step if a TX has already been stored

(See

page 5)

(See

page 5)

SEA

SET

END

SEA

SET

SPECIAL

Press OK to return to the

display of the inputs state.

Press OK to enter the special menu.

SEA

SET

Choose ON with

UP or DOWN

if you want to reverse

the direction of

the motor rotation

Per confermare

e tornare

al Menu principale

OK OK

REVERSE

MOTOR

The gate will execute a CLOSING-OPENING-CLOSING CYCLE

GATE 1 DG R2BF

INVERTER

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Default

SET

MENU FUNCTIONS TABLE GATE 1 DG R2BF

Description

Set value

Stop

Start

Stop

Unloch

Storing of a command

for unlocking an

electric brake

Italian

English

French

Spanish

2 - TRANSMITTERS

External module

Pedestrian Start

Clear memory

Delete a transmitter

External module

Pedestrian Start

Delete single transmitter

Delete transmitter memory

Olandese

1 - LANGUAGE

Español

English

Français

Italiano

Dutch

Start

Pedestrian

Start

End

“Transmitters” menu output

Barrier

Big

3 - MOTOR

Barrier

Big

8 - START IN PAUSE

6 - LOGIC

Automatic

Open-stop-close-stop-open

2 buttons

Safety

Dead man

Open-stop-close-open

Automatic

Step by step type 1

Step by step type 2

Two buttons

Safety

Dead man

7 - PAUSE TIME

Setting from 1s to 4min.

OFF

(semi-automatic logics)

9 - PROGRAMMING

10 - TEST START

15 - END

Start command

Times learning start

In pause start is not acceped

In pause start is accepted

(See page 6)

Automatic

1 240

Off

Off On

Off

Press OK to return to the display of the firmware version

and to the one of inputs state.

16 - SPECIAL MENU

Press OK to enter the special menu.

5 - REVERSE MOTOR

Off

Synchronized right motor

Synchronized left motor

Off

Lepus Fast

Centralina idraulica

Big Fast - Super Fast

English

Lepus Fast

Hydraulics units

Big Fast - Super Fast

Barrier

GATE 1 DG R2BF

INVERTER

Note: In case of three-phase version, the motors are: “Sliding” and “Sliding Fast”.

Sliding Fast

3 - MOTOR

Sliding

For single-phase version only

For three-phase version only

Sliding Fast

Sliding

FUNCTION LOGIC

AUTOMATIC LOGIC

A start impulse opens the gate. A second impluse during the opening will not be accepted.

A start impulse during closing reverses the movement.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi-

automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item

8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

SECURITY LOGIC

A start impulse opens the gate. A second impulse during opening reverses the movement.

A start impulse during closing reverses the movement.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi-

automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item

8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

STEP BY STEP TYPE 1 LOGIC

The start impulse follows the OPEN-STOP-CLOSE-STOP-OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi-

automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item

8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

STEP BY STEP TYPE 2 LOGIC

The start impulse follows the OPEN-STOP-CLOSE -OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi-

automatic.

NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item

8-START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

DEAD MAN LOGIC

The gate opens as long as the START button of opening is pressed; releasing it the gate stops. The gate closes as

long as the button connected to the PEDESTRIAN START is pressed; releasing it the gate stops. To execute

complete opening and/or closing cycles the related pushbuttons must be constantly pressed.

2 PUSHBUTTONS LOGIC

One start opens, one pedestrian start closes. In opening the closing will not be accepted. In closing a start command

reopens, a pedestrian start command (closes) will be ignored.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

WORKING TIMES SELF LEARNING

GATE 1 DG R2BF

INVERTER

1) Turn off electricity, release the motors and manually position the leaves on halfway.

Reset the mechanical lock.

2) Connect the control board to the power supply.

3) Before starting the learing, make sure (through the test menu), that the relative limit switches of every opening are

employed.

4) Select on the on-board display or JOLLY 3 programmer, the type of motor that you are using as indicated in the

dispaly management.

5) If necessary also set the operation logic and the other parameters. If you want to program with a transmitter, store a

transmitter before programming.

6) Select 9-PROGRAMMING on the display, press OK and than one of the UP or DOWN buttons.

(If the motor starts in opening, remove and re-put power supply, select on the display 5-REVERSE MOTOR.

And through the UP and DOWN button put it on ON, or if you have the Jolly 3 programmer, activate the motor

exchange function. )

7) At this point the gate will start the following cycle: CLOSING - OPENING - CLOSING.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

PRESS AT THE SAME TIME FOR 5 SECONDS TO ENTER OR TO EXIT THE SPECIAL MENU

UPDOWN

SPECIAL MENU FUNCTIONS TABLE GATE 1 DG R2BF INVERTER

For entering into the special menu move on one of the menu and press the UP and DOWN

buttons at the same time for 5 s. For exiting the special menu press END or move on one of the

menu and press the UP and DOWN buttons at the same time for 5 s.

SPECIAL MENU

10 100

18 - CLOSING SPEED

Setting from 10 to 100

10 100

17 - OPENING SPEED

Setting from 10 to 100

MENU SP

Default

SET

Description

Set Value

21 - OPENING SLOWDOWN

SPEED 1

22 - CLOSING SLOWDOWN

SPEED 1

10 60 from max. speed

Slowdown speed in opening

10 60 from max. speed

Slowdown speed in closing

33 - OPENING SENSITIVITY

MOTOR1

34 - CLOSING SENSITIVITY

MOTOR1

Disabled

Adjusts the intervention time

of the Encoder / Potentiometer

in opening

Off (Intervention excluded)

10% (Fast intervention)

99% (Slow intervention)

Disabled

Off (Intervention excluded)

10% (Fast intervention)

99% (Slow intervention)

Adjusts the intervention time

of the Encoder / Potentiometer

in closing

Enables the reading of the

potentiometer with LE card.

Potentiometer

Reports the current position

of the potentiometer on the

leaf. This parameter is useful

for seeing if the potentiometer

is read correctly.

Reports the impulses

stored by the control unit

when the leaf is fully open.

Reports the impulses stored

by the control unit when the

leaf of is fully close.

32 - ENCODER *

Off

- - - - - - - -

51 - I.PAR.M1 *

52 - I.AP.M1 *

53 - I.CH.M1 *

- - - - - - - -

32 - ENCODER *

In ON enables the Encoder

Off

xxx.

Encoder impulses during operation (Motor 1).

Encoder impulses stored in programming (Motor 1).

xxx.

48 - ENCODER TOT.1 *

47 - ENCODER PAR.1 *

GATE 1 DG R2BF

INVERTER

1 - 5

2.5

28 - OPENING A THRESHOLD *

29 - CLOSING A THRESHOLD *

Adjust inversion current on

motors in opening.

32 - ENCODER *

In OFF disabled the Encoder

Off

1 - 5

2.5

Adjust inversion current on

motors in closing.

0.0A

57 - WORKING CURRENT

Shows motor absorption

during operation

Off 50

60 - CLOSING SLOWDOWN 1

From OFF to 50% of

the stroke. Note: Not active

if the Four limit switch

interface card is present

Off 50

59 - OPENING SLOWDOWN 1

From OFF to 50% of

the stroke. Note: Not active

if the Four limit switch

interface card is present

For three-phase version only

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MENU SP

Default

SET

Description

Set Value

Off

79 - ANTI INTRUSION

Only closing

Only opening

Opening and closing

If you force the gate

manually, the control

unit starts the motor to

restore the state of the

gate before forcing.

0.0 5.0

Pre-flashing only

active before closing

Buzzer

85 - PREFLASHING

86 - FLASHING LIGHT

Only closing

Normal

Light

Always

Normal

Control lamp

Always ON

Pre-flashing time

Off

Normal

1 240

88 - COURTESY LIGHT

In cycle

Courtesy light setting

from 1s to 4min.

Courtesy light in cycle

Off on

Off

5 100%

100%

89 - TRAFFIC LIGHT

RESERVATION

When setting this function

the pedestrian input will be

activated to work on the

auxiliary board SEM

(traffic light management).

90 - PARTIAL OPENING

Setting from 5 to 100

= Start

91 - PARTIAL PAUSE

Pause in partial opening

same as in total opening

= Start

Off

Disabled

1 240

Setting from 1s to 4 min.

92 - TIMER

Off

On photo2

Off

On pedestrian entry

Transforms the selected

input in an input on

which to connect an

external clock.

Off

The flashing light remains

ON with active timer and

open gate

The flashing light remains

OFF with the active timer

and open gate

87 - FLASHING LIGHT

AND TIMER

Off

93 - FIRE SWITCH

Disabled

On photo2

On pedestrian entry

Active on Photo 2

Active on pedestrian

GATE 1 DG R2BF

INVERTER

0 20 s

1 s

70 - POSITION RECOVERY

(For three-phase version only)

Retrieves the inertia of the

motor in opening and closing

after Stop or reversing

Acceleration ramp.

Adjusts the motor start.

1 s

5 s

64 - ACCELERATION

2.5 s

50%

0 %

100%

Adjust the passage

between normal speed

and slowdown speed

63 - DECELERATION

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MENU SP

Default

SET

Description

Set Value

95 - AUTOTEST

Photo1

Photo2

Photo1-2

Autotest active only on

Photo1

Autotest active only on

Photo2

Autotest active on

Photo1 and Photo2

Off

Edge

Photo1 and Edge

All safe

Disabled

Autotest only on safety edge

Autotest photo 1 and

safety edge

Autotest photo 2 and

safety edge

Autotest photo 1, photo 2

and safety edge

Photo2 and Edge

Stop

97 - PHOTO1

Opening

Closing

Stop and close

Pause reload

Active in opening

and closing

Photocell active in closing

Photocell active before

opening

The photocell gives a

command to close during

opening, pause and

closing

The photocell charging the

pausing time

The photocell stops in closing

and closes when released

Closing

Shadow loop

Until occupied, with open

gate, it prevents reclosing.

It is switched off during

closing.

Stop

98 - PHOTO2

Opening

Closing

Stop and close

Pause reload

Active in opening

and closing

Photocell active in closing

Photocell active before

opening

The photocell gives a

command to close during

opening, pause and

closing

The photocell charging the

pausing time

The photocell stops in closing

and closes when released

Shadow loop

Until occupied, with open

gate, it prevents reclosing.

It is switched off during

closing.

Opening

GATE 1 DG R2BF

INVERTER

Always

AUX output always

power supplied

94 - 24V AUX (Programmable)

In cycle

In pause

Opening

Closing

AUX output power

supplied only during opening

AUX output power

supplied only during closing

AUX output power

supplied only during pause

AUX output active only

during cycle

Always

AUX output only during cycle

with fototest function active

Autotest

Security test

In cycle and fototest

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MENU SP

Default

SET

Description

Set Value

100 - EDGE1

8K2

Edge is active and

protected by a 8k2 resistor

Normal N.C. contact

Normal

102 - EDGE1

Only closing

Opening and closing

Only opening

Active in opening

and closing

Active only in opening

Active only in closing

Opening

and

closing

Normal

104 - SELECT LIMIT SWITCH

Ext

Limit switch in automatic

recognition

With LSE card

0 10E9 0

100 10E4

10E4

107 - MAINTENANCE CYCLES

108 - PERFORMED CYCLES

Setting from 100 to

100000

Reports the executed

cycles. Keep pressed OK

to reset the cycles

1 10

Shows last event

(See alarms table)

106 - DIAGNOSTICS

112 - PASSWORD

- - - -

Allows the entering of a

password blocking the

control unit parameters

modification.

Press OK to exit the special menu.

The special menu switches off automatically after 20 minutes.

Note 1: The * indicates that the default value or the menu may change depending on the selected motor type.

Note 2: After initialization the parameters "motor type" and "limit switch type" remain son the value chosen in the setup

program.

- - - -

120 - BASIC MENU

Normal

PASSWORD ENTERING MANAGEMENT

With a new control unit all menus can be displayed and set and the password will be disabled.

Selecting one of the Menus and keeping UP and DOWN pressed at the same time for 5 seconds, you will access the SP Menu

containing the 112-PASSWORD Submenu.

Pressing OK in the 112-PASSWORD Menu, you will proceed with the entering of the numeric code of the 4-digit password.

Use UP and DOWN to increase or decrease the number, press OK to confirm it and you will pass automatically to the entering of

the next number. Pressing OK after the last entered number the word “Sure?” appears, confirm the activation of the password

and the message OK appears, pressing UP or DOWN instead you can cancel the operation and “No operation” will appear on the

display.

Once entered the password, it will be definitively activated, once the display switch off timeout has expired, or by turning off and

on again the control unit. Once the password has been activated, the menus of the display can be only displayed but not set. To

unlock them you must enter the correct password in the112-PASSWORD menu, if the password is wrong the message “Error”

will appear.

At this point, if the password has been entered correctly, the menus will be unlocked and it will be possible to change the

parameters of the control unit again.

If the control unit has been unlocked through 112-PASSWORD Menu, it is possible to enter a new and different password, using

the same entering process as for the first one; at this point, the old password will no longer be valid.

If the password has been forgotten, the only way to unlock the control unit is to contact the SEA technical assistance, which will

assess whether to provide the procedure to unlock the control unit or not.

Note: The password cannot be set through the Jolly 3 terminal.

GATE 1 DG R2BF

INVERTER

1 s

5 s

- - - -

Adjust the motor stop.

On heavy gates it is

recommended to set this

value to minimes 2.5s.

115 - DECELERATION RAMP

Description

Start test

Stop test

Pedestrian

start test

Safety edge

test

Photocell 1

test

Photocell 2

test

Opening

limit switch

test

Closing

limit switch

test

The contact must be a N.O. Contact . When activating the related command

on the display SET lights up, the input works.

If SET is always on, check the wirings.

The contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works. If SET is always on, make

sure that the contact is a N.C. contact or that the related limit switch is not occupied.

The contact must be a N.O. Contact. When activating the related command

on the display SET lights up, the input works.

If SET is always on, check the wirings.

The contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

IThe contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works.

If SET is always on, make sure that the contact is a N.C. Contact

The contact must be a N.C. Contact. When activating the related command

on the display SET lights up, the input works. If SET is always on, make

sure that the contact is a N.C. Contact or that the related limit switch is not occupied.

Exit menu

MENU FUNCTION TABLE CHECK GATE 1 DG R2BF INVERTER INPUTS

To access the Menu for input check keep pressed OK for about 5 seconds.

Note: If the Stop, Photocell 1 and Photocell 2 contacts are not bridged in self-learning, they will be

deactivated and can be reactivated through this menu, without repeating times self-learning.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MENU FOR INPUT CHECK

DOWN

Initial system

Software Version

Programming example

SEA

SET

- - -

- -

- - -

DISPLAY INPUT STATUS

When the segment

is ON during self-

learning, the input

status is closed or

OFF.

Start

pedestrian

Stop

Limit

Switch

opening

motor

Photocell 1

Photocell 2

Edge

Limit

Switch

closing

motor

U.001

ITALIAN

LANGUAGE

ENGLISH

FRANCAIS

LIMIT SWITCH

CLOSING

LIMIT SWITCH

OPENING

START

EDGE1

PHOTO1

PHOTO2

PEDESTRIAN START

END

STOP

Enabled

Blocked

Enabled

Blocked

Enabled

Blocked

Enabled

Blocked

The settings of the control unit are made through the UP, DOWN and OK buttons. The UP and DOWN buttons to

scroll through the MENUS and SUBMENUS. By pressing OK you enter from MENU into SUBMENU and confirm the

choice.

Moving in the 1-LANGUAGE menu pressing the UP and DOWN buttons at the same time you access the SP MENU

for special settings.

Moving in the 1-LANGUAGE menu pressing the OK button for 5 seconds, you enter the CHECK MENU, where you

can check the operating status of all inputs.

GATE 1 DG R2BF

INVERTER

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

RADIO TRANSMITTER SELF LEARNING

WITH RECEIVER ON BOARD OF CONTROL UNIT

WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver into the

special CMR connector (if available) with turned off control unit.

With RF UNI and RF UNI PG module it will be possible to use both Coccinella Roll Plus transmitters and radio transmitters with fixed

code. The first memorized radio transmitter will determine the type of the remaining radio transmitters.

If the receiver is a Rolling Code, press twice the button of the radio transmitter that you want to program to memorize the first TX.

In the case of transmitters with fixed code it is necessary to press 1 time the button of the transmitter you want to program to store the first

remote control

Notes:

- Enter radio transmitters learning only when the working cycle stops and the gate is closed.

- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already associated to another function it will be

updated with the new function.

16 USERS Whitout memory

800 USERS With additional memory MEMO

100 USERS Fixed code

800 USERS Roll Plus

800 UTENTI Fixed code

800 UTENTI Roll Plus

RF UNI

RF UNI PG

Old model without additional memory

New model with MEMO additional memory

1 2 3 4

TABLE EXAMPLE

Transmitter

button

Memory

location

Serial number Customer

1 2 3 4

Transmitter

button

Memory

location

Serial number Customer

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

SEA

SET

START

PEDESTRIAN

START

EXTERNAL

MODULE

STOP

DELETE A

TRANSMITTER

OK? OK

CLEAR

MEMORY

PRESS

BUTTON

STORED

PRESS

BUTTON

PRESS

BUTTON

PRESS

BUTTON

If you want to program

the pedestrian

start as second

channel.

If you want to

delete a single

transmitter.

If you want to delete

the whole memory

If you want to program

the activation

of the LIGHT

output

as second channel.

Press the

button of the

transmitter

to be stored

Press the

button of the

transmitter

to be stored

Press the

button of the

transmitter

to be stored

Select with

UP or DOWN

the memory

location

to be deleted

and press OK

Press the

button of the

transmitter

to be stored

If you do not want to execute the cancellation,

press UP or DOWN to return to the

2-TRANSMITTERS menu.

Confirm the cancellation.

If you want to

program the

UNLOCH as

second channel.

SEA

SET

SEA

SET

SEA

SET

UNLOCH

STORED

PRESS

BUTTON

Press the

button of the

transmitter

to be stored

If you want to

program the

STOP as

second channel.

for 10 s.

SEA

SET

TRANSMITTERS

SEA

SET

SEA

SET

If you want

to exit the

2-TRANSMITTERS

Menu output

END

GATE 1 DG R2BF

INVERTER

CNS

RADIO TRANSMITTER SELF LEARNING

WITH RF FIX RECEIVER ON BOARD OF CONTROL UNIT

Connect the receiver on

the CNS connectors,

making sure that the

direction is the

one shown in the

illustration.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

WARNING: Make the radio transmitters programming before you connect the antenna and insert the receiver

into the special CNS connector (if available) with turned off control unit.

With the RF FIX module it will be possible to use only radio controls with fixed code.

Select through the display 2-TRANSMITTERS and press OK, now select with the UP and DOWN buttons, the command to which

you want to associate the button (it is possible to associate max. 2 commands) and press OK to confirm the choice, now press the

button of the radio transmitter which you want to associate. If the storage is successful, the display will show “Stored” .

In the 2-TRANSMITTERS MENU it is possible to select “Start” (to associate a Start command), “Pedestrian start” (to associate a

Pedestrian Start ), “External Module” (For the activation of a contact on the EXP output), “Stop” (To associate the STOP

command to the TX), “Unloch” (to associate the release of the electric brake to the transmitter), “Delete a transmitters” (To delet

the single transmitter only if it is a Rolling Code Plus), “Clear memory” (To delete all TX), “End” (To exit menu 2-TRANSMITTERS).

To release the electric brake it is necessary to give three consecutive pulses, the 4th will reactivate the lock of the electric brake.

Notes:

- Enter radio transmitters learning only when the working cycle stops and the gate is closed.

- It will be possible to memorize up to max. 16 codes (buttons) adding the MEM memory it will be possible to store up to 496

different codes.

- You can store max. 2 of the available 4 functions. If the control unit receives a code which was already associated to another

function it will be updated with the new function.

DELETE TRANSMITTERS FROM THE RECEIVER

With modules different from RF FIX, it will be possible to delete only the entire memory of the receiver.

Proceed as follows: select from the menu 2-TRANSMITTERS: “Clear memory” and hold the OK button until the display shows the

message “OK”.

GATE 1 DG R2BF

INVERTER

TIMER

TX1

TX2

1 2 3 4 5 6 7 8

RX1

RX2

START

START PED.

STOP

CN1

9 10 11 12 13

CN1

9 10 11 12 13

CN1

START (N.O.) The START is connected between connector 2 and 3 of the CN 1 terminal.

An impulse given to this contact opens and closes the automation depending on the selected logic, it can be given by a keyswitch, a keypad, etc. Holding

START starts the TIMER function, releasing the start, the operator repeats the pause and then performs the closing.

To connect the other devices refer to the related instructions leaflets. (ie. loop detectors and proximity switches). In the case of triggering a safety device the

timer will automatically reset after 6 seconds.

Note1: In DEADMAN logic keep pressed the Start for the opening of the automation.

Note2: In 2 BUTTONS logic this button performs the opening.

STOP (N.C.) The STOP is connected between the clamps 2 and 5 of the CN1 terminal .

When pressing this button the motor immediately stops in any condition/position. To re-start the movement give a start command.

After a stop the motor always re-starts in closing.

Can be activated through the on-board display or through the Jolly 3 programmer. In both cases it’s a N.O. contact which provoques the

opening of the automation keeping it open as long as it is activated. When it’s released, after having paused for the set pausing time the

gate recloses. The TIMER can be activated on the inputs FOTO2, PEDESTRIAN START or keeping busy the START input.

Note1: When activated on the pedestrian entry, the pedestrian will be OFF also on the radio transmitter.

Note2: In the event of an intervention of a security device during the timer (Stop, amperometric, Edge), a start impulse restors the

movement.

Note3: In case of no power supply with open gate and active Timer the control unit will restore its function, otherwise if during restoring of

the power supply the TIMER is not activated it will be necessary to give a start impulse for the reclosing.

PEDESTRIAN START (N.O.) The pedestrian start can be connected

between the conectors 2 and 4 of the CN1 terminal .

This input allows a partial opening, the opening space can be set through

the on-board display or through the JOLLY 3 device.

Note1: The contact for partial opening is a N.O. Contact (Normally open).

Holding START starts the TIMER function, releasing the pedestrian start,

the operator repeats the pause and then performs the closing. In the case of

triggering a safety device the timer will automatically reset after 6 seconds.

Note2:In 2 BUTTONS logic it is necessary to keep pressed the Start Ped. to

re-close the automation.

Note3: In deadman logic this button executes the re-closing if you keep it

pressed.

Note4: When closed during pause, the gate will reclose only after this input

has been reopened.

TIMER activation: This input can be transformed into TIMER (See TIMER).

Nota5: When using the Sem card, the pedestrian input can be used as

priority in closing through the 89-TRAFFIC LIGHT RESERVATION function.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

START - STOP - PEDESTRIAN START - ANTENNA -

PHOTOCELL

Photocell 1 and Photocell 2 Connections

Note: If the photocells are not connected, it is not necessary put a jumper between the clamps (6 and 7

and/ou 6 and 8 of the CN1 terminal)

+ = 24V (Accessories) 500 mA max COM = 0V PH1 = Photocell contact 1

PH2 = Photocell contact 2

Note: For the autotest connect the TX to the AUX clamp and activate the Autotest function.

The default setting of the photocell 1 is in “Closing” and the one of the photocell 2 is in “Opening”.

The photocell 2 can also be set as TIMER (see TIMER function).

OPTIONS ON FOTO1 and FOTO2 adjustable on on- board display or with Jolly 3 terminal.

“Closing”: if occupied, reverses the movement in closing, during pause it prevent the closing.

“Opening”: If activated the photocell blocks the movement as long as it’s busy, when released

the opening continues.

“Stop”: When activated before the opening the photocell blocks the automation as long as it is

busy, during the opening it will be ignored. In closing the intervention of the photocell causes the

reopening.

“Stop and close”: in opening it is not active; in pause are activated it commands the closing

when released, otherwise it’s not active; in closing it stops the movement as long as it is busy,

when released the closing continues.

“Close”: The photocell stops the gate as long as it is occupied in both opening and closing,

when released it gives a closing command (Closing one second after release of the photocell).

“Pause reload”: If occupied, during pause it recharges the timer of pause. In closing it reverses

the movement.

“Shadow loop”: Photocell aktive only during pause.

“Delay pause time”: If the photocell is occupied during opening, pause or closing, the gate

reopens completely and closes without observing the pause time.

Options AUX 24V 500mA (Programmable) max can be set with on-

board Display or with Jolly 3 device. It is possible to chose when having

tension on the AUX output. The options are: Always, In cicle, Opening,

Closing, In pause, Autotest, In cycle and fototest, Positive brake

management, Negative brake management, Negative brake management-

photocellule, Gate open warning light, Lock, Opening and open.

N.B: If you want the autotest just

connect the positive of the devices to

be tested on the input 10 (AUX) and

choose the device on which to

execute the test through the

“Autotest” or “In cycle and fototest”

function.

GATE 1 DG R2BF

INVERTER

AMPEROMETRIC MANAGEMENT

SAFETY EDGE AND FLASHING LAMP

SAFETY EDGE

Safety edges (EDGE) can be connected between the contacts 9 and 11 of CN1.

Pressing EDGE, the contact opens, causing a partial reversing of the gate in closing and opening.

Note1: If the edge contact is not used it must be

briged The EDGE input can be set: only in closing, .

only in opening or in both directions.

Note2: It is possible to activate a balanced edge

8K2 through the on board display or through the

Jolly 3 programmer, in such case the edge contact

will be controled by a specific resistance value,

detecting the possible involontary short circuit of

the device. In case of an imbalanced device a

special alarm will show on the on board display or

on the JOLLY 3 programmer.

Note: it is possible to perform an Autotest also on

the powered radio edge.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Waring lamp Flash Led 24V (Accessories) 3W Max (Control lamp)

The warning lamp can be connected between the terminals 24V (Accessories) and FL (-) of CN1

It blinks once per second during opening and twice per second during closing, while it remains lit during

pause.

Throught the warning lamp it is also possible to identify alarm signals comming from the STOP,

PHOTOCELL 1, PHOTOCELL2 and EDGE devices. Through the on board display or the Jolly 3

programmer it is possible to activate the pre-flashing function and/or to modify the flashing light function

choosing between fixed flashing, control lamp or Buzzer.

The pre-flashing can be set from 0 to 5 s. or it is possible to have it only before closing.

Safety edge

in closing

10 11 12 13

1 2 3 4 5 6 7 8 9

CN1

FL (-)

24V (Accessories)

Common

+ -

AMPEROMETRIC DEVICE FOR ELECTROMECHANICAL OPERATORS

This control unit comes with an obstacle detection system working only on electromechanical operators allowing to

have the reversing on obstacles and the automatic detection of the stops.

Sensitivity adjustable from OFF to 99% inside the special menu. The more the percentage is high the more the

obstacle detection will be difficult.

ENCODER (CN5 Connector)

The Encoder allows the detection of the gate position and its reversing in case of obstacles. To use the ENCODER it

is necessary to enable it inside the special 32-ENCODER Menu. The sensitivity on the obstacle is adjustable from 0 -

99%. The higher the percentage is the more it will be difficult to detect the obstacle.

NOTE: If the Encoder is activated it is possible to visualize in the special menu the total memorized impulses and the

partial impulses executed by the motor.

POTENTIOMETER "GATE POSITION"

If the POSITION GATE is present on hydraulic motors it will be possible to have the inversion on obstacles by

adjusting the menus 33- MOTOR1 OPENING SENSITIVITY, 34- MOTOR1 CLOSING SENSITIVITY, 37-

SLOWDOWN SENSITIVITY.

ATTENTION: The first operation, after power failure will be for searching the mechanical stops at the end of the run.

GATE 1 DG R2BF

INVERTER

FOUR LIMIT SWITCH WITH LSE CARD

Dip switch 1 = OFF

Dip switch 2 = ON

1 2

OFF

On the GATE1 DG INV to activate the

EXT mode on Limit Switch Menu.

I1 = Closing limit switch (green cable)

I2 = Opening limit switch (yellow cable)

GND = Common electronic control unit (grey cable)

I3 = Slowdown closing limit switch (pink cable)

I4 = Slowdown opening limit switch (white cable)

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

N o t e : T h e m o t o r i s a l r e a d y

synchronized with the limit switches. If

you invert the motor, you have to also

invert the limit switches.

POTENTIOMETER MANAGEMENT (Position Gate)

(Available from revision 013 only on prepared motors)

The position gate ensures the correct position of the gate and the inversion on the obstacle, helping the installer to pass the certification of the

automation.

To connect the potentiometer you must use the LE card (Cod.23001256) and set with Dip Switches 1 and 2 both in OFF.

With the potentiometer it is possible to access the hidden DEBUG menu to check the maximum settable value as threshold in normal and

slowdown speed.

To access this menu you have to press, in the menu that displays the firmware version, UP and OK at the same time until the menus VP1 speed

of potentiometer 1 will appear.

To view the speed of the potentiometer on the related menu, press OK.

To exit the DEBUG menu go to END and press OK.

If the reading of the potentiometer is reversed relative to the movement of the motor, on the display will appear the alarm "Potentiometer

direction" and you will have to reverse the brown wire with the green one and repeat programming..

For a quick inversion on the obstacle you have to lower the sensitivity parameters.

1 2

CN1

CNP

DS1

POTENC

1 2 4

P01 D1 P11 P02 D2 P12 I1

5 6 7

GND

I3 I4

3 8 9 10 11

+ -

LE CARD

EXP

D1 (White)

P01 (Green)

P11 (Brown)

Potentiometer 2

(Position Gate)

EXP

GATE1 DG INV

CONTROL UNIT

Display

1 2

CN1

DS1

POTENC

1 2 4

P01 D1 P11 P02 D2 P12 I1

5 6 7

GND

I3 I4

3 8 9 10 11

P01 to P12

NOT USED

Green

Yellow

Gray

Pink

White

GATE 1 DG R2BF

INVERTER

INVERTER MODULE CONNECTION

(Already wired)

(CMS) INVERTER

INTERFACE CONNECTOR

Insert on CN4

of the

Gate 1 Inverter

control unit

230Vac

Single-phase

230Vac

Single-phase

R S T

N L

CN3

230Vac Three phase

N R S T

R S

N L

CN3

SIGB

SIGA

COM

N L

CN3

Depending on

the version

(230V / 380V)

380Vac Three phase+N

Neutral

Line

230Vac

Single-phase

INVERTER

MODULE

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

GATE 1 DG R2BF

INVERTER

Note 1: If in the diagnostics shows "Max. cycles reached ", do the maintenance and / or reset the

number of cycles performed.

Note2: To exit from the error messages, press OK. If the error persists, make all required checks for the

specific error and / or disconnect the device that generates the error to see if the error disappears.

At each opening and closing of the automation the flashing light will blink. It blinks once per second

during opening and twice per second during closing, while it remains lit during pause.

It is possible to view the alarms also on the flashing light or on the control lamp, simply by observing the

number of flashes emitted and verifying the reference in the table below:

ALARM DESCRIPTION

Signals Kind of alarm

Solutions

Inverter failure

24V Power supply

failure

AUX output voltage

Power supply failure

Self-test photocells

failure

Limit switch

activation failure

Flashing lamp failure

Make sure there are no short circuits on the wiring or on the

control unit and no overloads.

Make sure there are no short circuits on wiring or control unit

and no overload.

Check the network or the F2 fuse

Check the photocells operation and / or connections on the

control unit.

Check the operation of both limit switches and / or

correspondence between movement direction of the motor

and engaged limit switches.

Check connections and / or conditions of the lamp.

Blinks

4 fast

Cause of alarm

Inverter failure

Photocell in closing

Photocell in opening

Safety edge

Cause of alarm

Stop

Max. Cycles reached

Collision in opening/closing

Limit switch fault

Check the connections between Gate 1 DG and inverter module.

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

FAILURE INVERTER

FAILURE24

FAILURE24VAUX

FAILURE NET

FAILURE SELF TEST

FAILURE LIMIT

SWITCH

FAILURE FLASHING LIGHT

FAILURE

POTENTIOMETER

Potentiometer failure

The message appears only if the potentiometer is ON and the

potentiometer (LE) card is broken or not connected.

GATE 1 DG R2BF

INVERTER

Advises

Make sure all Safeties are turned ON

Problem Found Possibile Cause Solutions

Motor doesn’t respond to any

START impulse

Gate doesn’t move while the

motor is running

Gate doesn’t reach the complete

Open / Closed position

The gate opens but doesn’t

The gate doesn’t close

automatically

a.) Check the connected N.C. Contacts

b.) Burnt fuse

a.) The motor is in the released position

b.) There is an obstacle

a.) Pause time set to high

b.) Control unit in semi-autom. logic

a.) Wrong setting of the limit switches

b.) Error on programming

c.) Gate is stopped by an obstacle

a.) The contacts of the photocells are

connected and open

b.) The stop contact is connected and open

c.) The edge contact is open

a.) Check the connections or the jumpers

on the connections of the safety edge or

of the stop and of the photocell if connected

b.) Replace the burned fuse on the control unit

a.) Re-lock the motor

b.) Remove obstacle

a.) Adjust pause time

a.) Set limit switches

b.) Repeat programming

c.) Remove obstacle

a.) b.) c.) Check the jumpers or the

connected devices and the signals

indicated on the warning lamp

b.) Set the pause parameter on a different

value from the OFF

TROUBLE SHOOTING

Page for both instaler and user

WAREHOUSING TEMPERATURES

min

Max

Dampness

min

Dampness

Max

5% Not condensing 90% Not condensing

MAINTENANCE

Considering the number of working cycles and the kind of gate, if the gate has changed the clutches and doesn’t work it’s necessary to

periodically proceed, with the learning times reprogramming on the electronic control unit.

Periodically clean the optical systems of the photocells.

REPLACEMENTS

Any request for spare parts must be sent to:

SEA S.p.A. - Zona Ind.le, 64020 S.ATTO - Teramo - Italia

SAFETY AND ENVIRONMENTAL COMPATIBILITY

Disposal of the packaging materials of products and/or circuits should take place in an approved disposal facility.

REGULAR PRODUCT DISPOSAL (electric and electronic waste)

(It’s applicable in EU countries and in those ones provided with a differential waste collection)

The brand that you find on the product or on documentation signals that the product must not be disposed off together with other domestic

waste at the end of life cycle. In order to avoid any possible environmental or health damage caused by irregular waste disposal, we

recommand to separate this product from other forms of waste and to recycle it in a responsible way in order to provide the sustainable re-use of

material resources. Domestic users are invited to contact the retailer where the product has been purchased or the local office in charge of all

the information related to differential watse collection and recycling of this kind of product.

STORING

Materials handling must be made with appropriate vehicles..

WARRANTY LIMITS

For the guarantee see the sales conditions on the official SEA price list.

SEA reserves the right to make any required modification or change to the products and/or to this manual without any advanced notice

obligation.

- 20°C + 65°C

d.) Amperometric threshold too low

d.) Increase the current threshold parameter

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

GATE 1 DG R2BF

INVERTER

La pagina sta caricando ...

SEA Gate 1 DG R2BF Manuale del proprietario

Marca: SEA

Modello: Gate 1 DG R2BF

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: SEA Gate 1 DG R2BF Owner's manual

SEA Gate 1 DG R2BF Manuale del proprietario

SEA Gate 1 DG R2BF Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti