Buffalo Technology Network Card WLI-U2-AG108HP Manuale utente

User Manual

Wireless 54 Mbps

USB Adapter

with Antenna Interface

WLI2-USB-G54

www.buffalotech.com

v1.5

User Manual - AirStation WLI-U2-AG108HP

High Power Dual A+G Wireless USB 2.0 Adapter

2

Congratulations on your purchase! The AirStation WLI-U2-AG108HP High-Power Dual A+G

Wireless USB 2.0 Adapter connects to 2.4ghz 802.11g networks, 2.4ghz 802.11b networks,

and 5ghz 802.11a networks.

System Requirements

• A compatable A, B, or G band access point.

• A PC running Windows XP, 2000, ME, or 98se.

Package Contents

• WLI-U2-AG108HP USB Adapter

• Stand

• 5 foot USB Cable

• Utility CD with Manual

• Quick Setup Guides

• Warranty Statement

Introduction

3

Antenna

The WLI-U2-AG108 includes a directional

antenna. For best performance, point the

antenna so that the word “BUFFALO” on the front

faces your access point.

The WLI-U2-AG108 may also be removed from

its stand and clipped to the top of your notebook

computer. Lift the tabs gently to open the clamp,

and slip the unit onto the edge of your computer

screen.

4

Getting Started

1. Installing Drivers:

Insert the AirNavigator CD into the CD-ROM drive of the PC.

If setup.exe does not launch

automatically, click Start

and select Run. Enter

D:\Setup.exe in the Open

eld, where D: is the letter

assigned to your CD-ROM.

Click the OK button to

launch the wizard.

5

Select Install Wireless

Drivers. Click OK.

The wireless driver

installation program

will begin. Press NEXT

and follow the on screen

prompts.

AirNavigator

6

Installing Drivers

2. Installing the Wireless USB Adapter with Windows XP:

Once the driver les have been installed, your computer will prompt you to insert

your wireless adapters. At this point, please plug the Wireless USB Adapter into your

computer.

The setup should automatically complete. If it automatically nishes the install, then

skip to Page 8, otherwise, Select Install the software automatically. Click the Next button.

7

Installing Drivers

A list of drivers will appear. Choose WLI-U2-AG108HP from the list and click Next .

If Windows warns you that this driver does not pass Windows Logo testing, click Continue

Anyway. When installation is nished, click Finish. Restart your PC if prompted.

8

3. Using Wireless Zero Configuration:

Normally, Windows XP will scan for available wireless

access points once the Wireless Notebook Adapter

is installed. If Windows detects an access point, a

networking icon appears on the task bar. One or more

wireless networks are available appears as a caption

accompanying the icon.

Notes: If Wireless Zero Conguration is not running,

click Start>Control Panel>Administrative Tools>Services.

Select Automatic in the Startup Type eld of the Wireless

Zero Conguration Service to start it.

If you don’t want to use Wireless Zero Cong and

would rather use Buffalo’s client utility, or if you have a

Windows 98 or 2000 computer, turn to page 12.

Right click the networking icon in the taskbar and select

View Available Wireless Networks to display a list of

available wireless networks. Select a network and click

Connect.

If the network that you are connecting to is unsecured,

you may need to check the box allowing you to connect

to an unsecured network.

Wireless Zero Configuration

9

Click the Advanced button to enter an SSID network name or WEP/WPA encryption key

manually. To add an SSID network name that is not listed, click the Add button.

Connecting

10

Connecting

To enter an encryption key, select the appropriate

wireless network and click the Congure button.

From the pull down menu, select the appropriate type

of Data encryption for the wireless network. Enter

and conrm the Network Key (encryption key). Click

the OK button when nished.

11

Installation with Windows 98/ME/2000

Windows 98/ME/2000

1. Installing the Wireless USB Adapter:

Power on the notebook PC and let it boot into Windows. Plug the Wireless USB Adapter

into an available USB port on your PC. The Found New Hardware Wizard will launch

automatically.

If this screen doesn’t appear, remove the Wireless USB Adapter and restart the notebook.

Reinsert the Wireless USB Adapter once the notebook has rebooted.

Select Install the software automatically. Click the Next button.

12

Installation / Setup

2. Installing the Wireless USB Adapter Drivers:

Insert the AirNavigator CD. Click Next at the Welcome to the Found New Hardware

Wizard. Select Search for a suitable driver for my device. Click Next to continue.

Check only the CD-ROM drives checkbox, and clear any other checkboxes that are

selected. Click Next to continue.

13

Installation / Setup

Windows will display a driver you can use with the Wireless USB Adapter.

Click Next.

In Windows 2000, if the Digital Signature

Not Found page opens as shown, click

Yes to continue the installation process.

When the Wireless USB Adapter is

successfully installed, click Finish.

Restart your computer if prompted.

See the next page to install the Client

Manager.

14

Use Client Manager to congure your wireless network, survey and connect to available

access points, enable and use WEP encryption, and create connection proles.

Note: Client Manager does not function properly if the Windows XP Wireless Zero

Conguration Service is enabled.

Installing Client Manager

Insert the AirNavigator CD. The

AirNavigator dialog box will open automatically.

If the AirNavigator dialog box does not open

automatically, select Start»Run and enter D:\

Setup.exe in the Open eld to open the dialog

box manually. D: represents the letter assigned

to the CD-ROM drive. If another letter is

assigned to the CD-ROM drive, your command

should reect that difference. Click the OK

button. Select Install Client Manager to launch

the InstallShieldWizard.

Once the InstallShield Wizard launches,

click the Next button to begin the software

installation.

Client Manager

15

Client Manager

Once the Installer Wizard launches, click the Next button to begin the software

installation.

Press I Agree to accept the license agreement and continue the installation process.

16

Client Manager

Press the OK button to nish and close the

installation program.

Press the Exit button to exit the

AirNavigator installation utility.

The Buffalo Client Manager is now installed

and running; right clicking on its icon (the

black notebook icon) will allow you to begin

using it.

17

Use Client Manager to congure your wireless network. To assist in conguring your

wireless network, Client Manager consists of the Status page, the Survey page, and the

Proles page. You can access each page by clicking the corresponding button on Client

Manager. In addition to these pages, several dialog boxes are available to meet specialized

conguration needs. You can access the Edit Prole dialog box, New Prole dialog box,

IP Conguration dialog box, or WEP Conguration dialog box using the Client Manager

pages.

Status Page

Click Status to open this page. By

default, this page is displayed when

you start Client Manager. Details of

connection status are displayed.

This page only displays connection

information; no changes to settings are

made here.

This page includes the following

components:

• Adapter Name – Displays the part

number of wireless hardware that is

being used.

Client Manager Configuration

18

Client Manager Configuration

• Network Type – Displays what mode the network device is in. Ad-Hoc or

Infrastructure are the available modes.

•

Rate – The speed that the two wireless clients are communicating at. If the Client

Manager is not connected to a remote wireless device (access point or another client)

then no rate will be displayed.

•

Channel – The channel that the two wireless clients are communicating at. If the

Client Manager is not connected to a remote wireless device (access point of another

client) then no channel will be displayed. The available channels for use are 1-11.

•

Security– The type of encryption that the two wireless clients are communicating with.

If the Client Manager is not connected to a remote wireless device (access point of

another client), then ‘No Encryption’ will be displayed.

•

IP Address – The IP address of the machine the Client Manager is installed on. If

the Client Manager is not connected to a remote wireless device (access point of

another client) or is not connected to a network with DHCP, then no IP address will be

displayed.

•

MAC Address – The MAC address of the wireless client device inside the computer

Client Manager is installed on. If no wireless device is present in the computer, then no

MAC Address will be displayed.

•

Signal Strength – Displays the strength of the signal. Signal Strength is based on the

peak signal level the wireless adapter receives from the wireless device to which it is

connected. Next to the signal level is the wireless hardware type that the computer has

available.

19

Client Manager Configuration

Click the Survey tab to open this page. Here, you can survey the area, display available

access points, and connect to available access points.

This page includes the following components:

• Wireless SSID – Displays the SSID associated

with each available access point. The SSID is

the unique network name that functions as an

identier for your wireless devices. All wireless

devices on a network must use identical SSIDs to

successfully communicate.

• Wireless Mode – Displays the mode/rate set that

the remote wireless device is offering.

• Strength – Displays the relative strength of the

wireless networks.

• Encryption – Displays whether the wireless

network is using any sort of encryption.

Press the Connect button to connect to a listed SSID, or press the Refresh button to

perform another survey and update the survey list.

20

Client Manager Configuration

Once the Connect button is pressed, you will be prompted to enter any encryption related

information.

The Encryption drop down list allows you to

select the type of encryption for the network.

The correct encryption type should already be

selected automatically.

The Encryption Key is where the actual key

required by the wireless network must be

inputted. Please consult your wireless access

point or router’s documentation for proper

input of the encryption keys. Some wireless

networks may allow you to enter multiple keys;

four separate elds are available for this. If your

network only uses one encryption key, then

please use eld 1 to enter your key.

The Register Prole option will store this wireless

network in your proles. This means you will automatically connect to this network

when inside its range. This is recommended if you plan on using this wireless network

more than once.

Press the Connect button once you have completed entering the information.

La pagina sta caricando ...

Buffalo Technology Network Card WLI-U2-AG108HP Manuale utente

Questo manuale è adatto anche per

Buffalo Technology Network Card WLI-U2-AG108HP Manuale utente

in altre lingue

Documenti correlati

Altri documenti