TEAC CD-P1260MKII Manuale del proprietario

ENGLISH FRANÇAIS

ESPAÑOL

DEUTSCH ITALIANO

NEDERLANDS SVENSKA

77-20P126001002

Z

CD-P1260MK"

Compact Disc Player

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

GEBRUIKERSHANDLEIDING

BRUKSANVISNING

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A

SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN

REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to oper-

ate the equipment.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the manufac-

turer, or sold with the apparatus. When a

cart is used, use caution when moving the

cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

IMPORTANT SAFETY INSTRUCTIONS

3

ENGLISH

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a book

case or similar unit.

o The apparatus should be located close enough to the AC outlet

so that you can easily reach the power cord plug at any time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine, fire

or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiva-

lent type.

Laser information

This product contains a semiconductor laser system inside the cabinet

and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: EP-C101

Manufacturer: GUANGDONG EVER BRIGHT GROUP CO.,LTD

Laser output: Less than 1 mW on the objective lens

Wavelength: 790±25nm

V Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire,

injury or the staining of nearby things. Please read and observe the

following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery com-

partment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on human

health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or cad-

mium (Cd) as defined in the Battery Directive (2006/66/

EC), then the chemical symbols for those elements will

be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

This product is protected by certain intellectual property rights of Microsoft.

Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.

Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.

4

Contents

Thank you for choosing this TEAC product. Read this manual

carefully to get the best performance from this unit.

IMPORTANT SAFETY INSTRUCTIONS ..............................2

Included accessories .............................................4

Before use ........................................................5

Remote control unit ..............................................5

Connections .....................................................6

Discs .............................................................6

Identifying the parts (main unit) ..................................8

Identifying the parts (remote control unit) ........................9

Basic operation ................................................. 10

Repeat playback .................................................13

Shuffle playback .................................................14

Intro check ......................................................14

Program playback ...............................................15

Search mode (MP3/WMA disc only) ..............................18

Troubleshooting ................................................20

Specifications .................................................. 21

MP3/WMA disc playback order ................................. 21

Included accessories

Check to be sure the box includes all the supplied accessories shown

below.

Please contact the store where you purchased this unit if any of these

accessories are missing or have been damaged during transportation.

RCA cable × 1

Remote control unit (RC-1326) × 1

Battery (AAA) for remote control × 2

Owner’s manual (this document) × 1

o Keep this manual in a safe place for future reference.

o See page 142 for warranty information.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to

open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the product name in the “Products” section.

4) Select and download the updates that are needed.

5

ENGLISH

Before use

Read this before attempting any operations.

< In order to enable good heat dissipation, leave at least 20 cm (8”)

between this unit and walls and other equipment when installing

it. If you put it in a rack, take precautions to prevent overheating

by leaving at least 5 cm (2”) open above the top of the unit and at

least 10 cm (4”) open behind the unit. Failure to provide these gaps

could cause heat to build up inside and result in fire.

< Do not place anything on top of the unit.

< During playback, since the disc is revolving at high speed, do not

lift or move this unit. Doing so could damage the disc.

< Always remove the disc before relocating or moving this unit.

Moving the unit with a disc inside it could cause malfunction.

< The voltage supplied to the unit should match the voltage that is

printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Choose the installation location of your unit carefully. Avoid plac-

ing it in direct sunlight or close to a source of heat. Also avoid

locations that are subject to vibrations or excessive dust, heat, cold

or moisture.

< Do not place the unit on an amplifier or receiver or any other

device that generates heat.

< Do not open the cabinet as this might result in damage to the cir-

cuitry or cause electrical shock. If a foreign object should get into

the unit, contact your dealer.

< When removing the power plug from the wall outlet, always pull

directly on the plug. Never yank on the cord.

< To keep the laser pickup clean, do not touch it and always close

the disc tray.

< Do not attempt to clean the unit with chemical solvents as they

might damage the finish. Use a clean, dry or slightly damp cloth.

< Keep this manual in a safe place for future reference.

Remote control unit

Precautions for use

V

Misuse of batteries could cause them to rupture or leak

leading to fire, injury or the staining of items nearby.

Please read and observe the precautions on page 3

carefully.

< When using the remote control, point it towards the remote sensor

on the front panel of the main unit.

< Even if the remote control unit is used within its effective range,

operation by remote control might be impossible if there are any

obstructions between the unit and the remote control.

< If the remote control unit is operated near other devices that gen-

erate infrared rays, or if other remote controls that use infrared rays

are operated near the unit, this unit might operate incorrectly. The

other devices might also operate incorrectly.

Battery Installation

1. Remove the battery compartment cover.

2. Insert two AAA dry batteries. Make sure that they are inserted with

their positive (+) and negative (_) poles oriented correctly.

3. Close the cover.

Battery Replacement

If the distance from the main unit that the remote control works effec-

tively decreases, the batteries are probably exhausted. Replace the

batteries with new ones when this happens.

For more information about the collection of batteries, please contact

your local municipality, your waste disposal service or the place where

you purchased them.

6

Discs

Discs that can be played on this unit:

Caution:

Playback of any other type of disc could cause loud noise and

damage to speakers as well as harm hearing. Never play back any

other type of disc.

< Depending on the quality of the disc and/or the condition of the

recording, some discs might not be playable.

< Video CDs, CD-ROMs and similar types of discs can be read by the

unit, but they will make no sound when played back.

< Video and audio DVDs, DVD-ROMs and other types of DVDs can-

not be read and played back by this unit.

Caution:

If you put a video or audio DVD, DVD-ROM or other DVD into

the disc tray, the unit will attempt to read the disc and rotate at

high speed. If you accidentally insert such a disc, wait until the

unit stops spinning before ejecting it in order to avoid possibly

damaging the disc. (Do not attempt to remove the disc when

“

” appears on the screen.)

< Copy-protected discs and other discs that do not conform to the

CD standard might not play correctly in this player. If you use such

discs in this unit, TEAC Corporation and its subsidiaries will not

be responsible for any consequences or guarantee the quality of

reproduction. If you experience problems with such non-standard

discs, you should contact their issuers.

About CD-R/CD-RW discs

This unit can play back CD-R and CD-RW discs that have been

recorded in the audio CD format (CD-DA).

< Discs created by a CD recorder must be finalized before use with

this unit.

o WMA files

Windows Media Audio Professional (WMA Pro) and Windows

Media Audio Lossless (WMA Lossless) formats are not supported.

< Depending on disc quality and recording conditions, playback of

some discs might not be possible. Please see the manual for the

device that you used to create the disc.

< If you are uncertain about the handling of a CD-R or CD-RW disc,

please contact the seller of the disc directly.

CDs that bear the (12cm/8cm) “COMPACT disc DIGITAL AUDIO”

logo.

CD-R and CD-RW discs that have been correctly recorded in the

audio CD format and finalized.

Finalized CD-R and CD-RW discs that contain MP3 and WMA

files.

Caution:

< Turn off the power of all the equipment before making

connections.

< Read the instructions of each component that you intend to use

with this unit.

< Be sure to insert each plug securely. To prevent hum and noise, do

not bundle connection cords with power cords.

CD IN

RL

CD-P1260mkII

B

A

Wall outlet

Amplifier

A

LINE OUT jacks

An analog 2-channel audio signal is output from these jacks.

Connect it to the CD input jacks of an amplifier with RCA cables.

Be sure to connect:

White plug q White jack (L: left channel)

Red plug q Red jack (R: right channel)

B

AC Power Cord

After all other connections are complete, connect the plug to an

AC wall outlet.

Be sure to connect the power cord to an AC outlet that supplies

the correct voltage.

Hold the power plug when plugging or unplugging the power

cord. Never pull or yank on the power cord.

Connections

7

ENGLISH

Caution:

< Do not play any disc that is warped, deformed or damaged.

Playing such discs could cause irreparable harm to the playing

mechanisms.

< Printable CD-R and CD-RW discs are not recommended because

their label sides could be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do not

use any protective coating sprays.

< Use a soft oil-based felt-tipped pen to write information on the

label side. Never use a ball-point or hard-tipped pen, as this could

cause damage to the recorded side.

< Never use a stabilizer. Using commercially available CD stabilizers

with this unit will damage the mechanisms and cause them to

malfunction.

< Do not use irregularly-shaped discs (octagonal, heart-shaped, busi-

ness card size, etc.). CDs with these shapes could damage the unit.

Handling precautions

< Always place the disc on the disc tray with the label side up. Only

one side of a Compact Disc can be played or used for recording.

< To remove a disc from its storage case, press down on the center

of the case and lift the disc out, holding it carefully by the edges.

How to remove the disc How to hold the disc

Storage precautions

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high-temperature and

humidity for extended periods. Long exposure to high tempera-

tures will warp discs.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they are

not stored in locations where they will be exposed to direct sun-

light. They should also be kept away from sources of heat, such as

radiators and heat-generating electrical devices.

Maintenance

< If a disc becomes dirty, wipe its surface radially from the center

hole outward towards the outer edge with a soft, dry cloth.

< Never clean discs using chemicals such as record sprays, antistatic

sprays and fluids and thinner. Such chemicals will do irreparable

damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a CD-R or

CD-RW disc, read the precautions supplied with the disc or contact

the disc manufacturer.

About MP3/WMA files

This unit can play MP3/WMA files that are on CD-R/CD-RW discs.

Audio file formats that can be played

MP3 (“.mp3” extension)

Bit rate: 8–320 kbps

Sampling frequency: 16–48 kHz

WMA (“.wma” extension)

Bit rate: 48–192 kbps

Sampling frequency: 32, 44.1, 48 kHz

DRM (digital rights management) is not supported.

File information display

The display of this unit can only show single-byte letters and numbers.

< If a file information uses Japanese, Chinese or other double-byte

characters, playback is possible but the name will not be shown

correctly. In such cases, “

” is displayed.

Cautions when preparing MP3/WMA files using a computer or

other device

< Always add the correct extension to the file name. Files without

extensions cannot be recognized.

< Always close the session (complete disc creation). This unit cannot

play discs if the session has not been closed.

< Carefully read the manual for the software that you are using when

you create an MP3/WMA disc.

Discs that are unplayable or only partially playable

< Files without extensions cannot be played. Files that are not in the

MP3/WMA format cannot be played even if they have extensions.

< Variable bit rate files might not play back correctly.

< If the disc has more than 999 files or 255 folders, this unit can only

play back the first 999 files and files in the first 255 folders.

< Depending on disc conditions, this unit might not be able to play a

disc or skipping might occur.

8

A

POWER button

Press this button to turn the unit on and off.

B

Disc tray button

C

OPEN/CLOSE button (

-

)

Press this button to open and close the disc tray.

D

Play/Pause button (y/J)

Press this button to start or pause CD/MP3 playback.

E

Stop button (H)

Press this button to stop CD/MP3 playback.

F

Skip buttons (.//)/Search buttons (m/,)

Press these buttons to skip through tracks/files.

Hold down these buttons to search for a part of a track/file.

G

MP3 FOLDER buttons ( j/k)

During playback of an MP3/WMA disc, use these buttons to

select folders on the disc (page 12).

H

PROGRAM button

Use this button to program tracks/files (page 15).

I

REPEAT button

Use this button to enable repeat playback (page 13).

J

SHUFFLE button

Use this button to enable shuffle playback (page 14).

K

Display

L

Remote sensor

When operating the remote control, point it towards here.

M

PHONES jack/LEVEL knob

To listen with headphones, turn the LEVEL knob to minimize the

volume level before connecting the headphones plug to the

PHONES jack. Then, adjust the volume after connecting the plug.

Connected speakers will make no sound when headphones are

plugged in.

Caution:

Do not connect headphones with the PHONES jack while

wearing them. Moreover, do not disconnect headphones

or turn the unit on or off while wearing them. Very loud

sound could be output from the headphones.

AVOID DAMAGING YOUR HEARING

-

Do not put on

headphones until after plugging them in.

Identifying the parts (main unit)

A

BCDE F

GHI

J

KL

M

9

ENGLISH

Identifying the parts (remote control unit)

When both the main unit and the remote control have buttons

with the same functions, the instructions in this manual refer to

only the main unit buttons, but the remote buttons can be used in

the same way.

a

STANDBY/ON button

Turns the unit on and puts it into standby.

This can only be used when the POWER switch on the main unit

is set to ON.

b REPEAT buttons (1/FOLDER/ALL, A-B)

Use this button to enable repeat playback (page 13).

c

FOLDER buttons (j/k)

When playing MP3/WMA files, use these to skip to the previous

or next folder (page 12).

d

DISPLAY button

When playing an MP3/WMA disc, use this to change the display

of file information (page 12).

This button is also used in MP3/WMA search mode (page 18).

e

Stop button (H)

Use this button to stop playback.

f

Play/Pause button (y/J)

Use this button to start or pause playback.

g

Number buttons

Use these buttons to select tracks/files.

h

OPEN/CLOSE button (

-

)

Press this button to open and close the disc tray.

i

SHUFFLE button

Use this button to enable shuffle playback (page 14).

j

INTRO CHECK button

Use this button to start using the Intro Check function (page

14).

k

FILE buttons (j/k)

When playing MP3/WMA files, use these to skip to the previous

or next file (page 12).

l

TIME button

Press when playing an audio CD to change the display.

m ENTER button

Use to confirm the selection of a folder, for example.

n

Skip buttons (.//)

Press these buttons to skip through tracks/files.

o

Search buttons (m/,)

Press and hold during playback to search forward/backward.

p

PROGRAM button

Use this button to program tracks/files (page 15).

a

b

c

d

e

f

g

h

i

j

k

l

m

n

o

p

10

Basic operation

1

Press the POWER switch to turn the unit on.

< Playback begins automatically if a disc is already inserted.

2

Press the OPEN/CLOSE button (L) to open the tray.

3

Place a disc on the tray with the label side up.

< Never place more than one disc on the tray.

< The disc must be centred on the disc tray. If the disc is not

correctly loaded, it might not be possible to open the tray again

after it has been closed. Confirm that the disc is always centered

on the tray before closing it.

< Do not force the tray by hand when opening and closing it.

4

Press the OPEN/CLOSE button (L) to close the tray.

< After closing the tray, loading the disc takes a few seconds. No

buttons will work while loading. Wait until the total number of

tracks/files is displayed.

< When no disc is loaded in the CD player, “ ” is displayed.

When an audio CD is loaded

When an MP3/WMA disc is loaded

5

Press the Play/Pause button (

y

/

J

) to start playback.

Playback starts from the first track/file on the disc.

< MP3/WMA files that are not in folders are automatically put in

the “ROOT” folder. Playback starts from the first file in the ROOT

folder.

< When playback of all the tracks/files has finished, the unit stops

automatically.

< See page 21 for information about the playback order of

MP3/WMA discs.

Total tracks

Total playing time

Total number of folders

Total number of files

11

ENGLISH

Suspending playback temporarily

(Pause mode)

Press the Play/Pause button (G/J ) during playback to stop

playback at the current position. To resume playback, press the

Play/Pause button (G/J) again.

Stopping playback

Press the Stop button (H) to stop playback.

Searching for a part of a track/file

Hold down

During playback, hold down a Search button (m or ,) to

search a part of a track/file. Release it when you find the beginning

of the part you want to hear.

Skipping to an earlier or later track/file

During playback

Press a Skip button (.//) repeatedly until the desired track/

file is selected. The selected track/file will be played from the

beginning.

When playback is stopped

Press a Skip button (.//) repeatedly to select the track/file

you want to hear. Then, press the Play/Pause button (G/J) to

start playback of the selected track/file.

< If the . button is pressed once during playback, the track/file

being played will be played again from the beginning. To return

to the beginning of the previous track/file, press the . button

twice.

< During program playback, tracks/files in the program are selected

and played.

Direct Playback

When stopped or playing back, you can use the Number buttons on

the remote control to select tracks/files.

Select a track/file using the Number buttons, and press the Play/

Pause (G/J) button within 10seconds to start playback of the

selected track/file.

Examples:

Track/file 7:

Track/file 23:

< Direct playback is not possible during shuffle playback and

program playback.

12

Listening with headphones

To listen with headphones, turn the LEVEL knob to minimize the

volume level before connecting the headphones plug to the

PHONES jack. Then, adjust the volume after connecting the plug.

Connected speakers will make no sound when headphones are

plugged in.

Caution:

Do not connect headphones with the PHONES jack while

wearing them. Moreover, do not disconnect headphones or

turn the unit on or off while wearing them. Very loud sound

could be output from the headphones.

AVOID DAMAGING YOUR HEARING - Do not put on

headphones until after plugging them in.

Changing the playback time display

During CD playback, press the remote control TIME button to change

the display.

Song elapsed

time

e

Song

remaining

time

e

Disc elapsed

time

e

Disc

remaining

time

Displaying MP3/WMA information

During MP3/WMA playback, press the DISPLAY button to show

information about the playing file on the display. Press again to cycle

through the information shown in the following order.

File name e Song e Albume Artist

Press the DISPLAY button for more than 1second again to cancel the

MP3/WMA information mode.

< “

” appears when there is no information.

< “

” appears when the unit cannot read the information.

< The display of this unit can only show single-byte letters and num-

bers. If a file name uses Japanese, Chinese or other double-byte

characters, playback is possible but the name will not be shown

correctly. In such cases, “

” is displayed.

Skipping to the next folder (MP3/WMA)

Press the MP3 FOLDER buttons (j/k)

to skip folders.

Use the remote control FILE buttons (j/k) to skip files.

Basic operation (continued)

13

ENGLISH

Press the REPEAT button to cycle through the following playback

modes:

When an audio CD is loaded.

REPEAT

(Repeat one track/file)

REPEAT ALL

(Repeat all tracks/files)

Off (normal playback)

When an MP3/WMA disc is loaded.

REPEAT

(Repeat one

track/file)

REPEAT ALBUM

(

Repeat all the files

in the folder

)

REPEAT ALL

(Repeat all

tracks/files)

Off (normal playback)

< If one of the following buttons is pressed, the repeat mode will be

canceled:

Main unit

POWER button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button

Remote control unit

STANDBY/ON button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button, INTRO CHECK button

Repeat one track/file (REPEAT)

The track/file being played will be played repeatedly.

Press the REPEAT button once during ordinary playback. “REPEAT”

appears on the display.

< If you press the Skip button (. or /) to select another track/

file, the selected track/file will be played repeatedly.

< You can select a track/file to be repeated when playback is

stopped. Press the REPEAT button, select a track/file using a Skip

button (. or /), and then press the Play/Pause button

(G/J) to start playback.

Repeat all the files in the folder (REPEAT ALBUM) (MP3/WMA

only)

All the files in the selected folder will be played repeatedly.

Press the REPEAT button twice during ordinary playback. “REPEAT

ALBUM” appears on the display.

Repeat all tracks/files (REPEAT ALL)

All the tracks/files on the disc will be played repeatedly.

During audio CD playback, press the REPEAT button twice. During

MP3/WMA disc playback, press the REPEAT button three times.

Press the REPEAT button twice during ordinary playback. “REPEAT

ALL” appears on the display.

< During program playback, the programmed tracks/files will be

played repeatedly.

A–B repeat

A specific part of a song can be played back repeatedly.

Play the CD, and press the A-B button at the beginning of the part you

want to repeat (A point).

The REPEAT indicator and A appear on the display.

Press the A-B button again at the end of the part you want to repeat

(B point). Repeat playback of the specified part (A-B) starts and “b”

appears to the right of “A”.

o A-B repeat playback is possible during ordinary repeat playback or

shuffle playback.

o If one of the following buttons is pressed, the repeat mode will be

canceled:

Main unit

POWER button, OPEN/CLOSE button (L ), Skip buttons

(.//), Stop button (H), SHUFFLE button

Remote control unit

STANDBY/ON button, OPEN/CLOSE button (L), Skip buttons

(.//), Stop button (H), SHUFFLE button, A-B button, Search

buttons (m/,)

Repeat playback

14

The tracks/files on a disc can be played in random order.

Press the SHUFFLE button in the stop mode. “SHUFFLE” appears on

the display.

< If you press the / button during shuffle playback, the next

track/file will be randomly selected and played. If you press the

. button, the currently played track/file will be played from the

beginning.

Press again to return to the previous song.

During shuffle playback, a track/file that has completed playback

will not be played again.

< During shuffle playback, tracks/files cannot be selected using the

Number buttons.

< Repeat playback is not possible during shuffle playback.

< After all tracks/files have been played once, playback ends and

shuffle mode is cancelled.

< If one of the following buttons is pressed, shuffle mode will be

cancelled:

Main unit

POWER button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button

Remote control unit

STANDBY/ON button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button, INTRO CHECK button

Shuffle playback

Ten seconds of the beginning of each track/file can be played back in

succession.

Press the INTRO CHECK button during playback or when stopped.

The INTRO indicator appears on the display, and 10seconds of the

beginning of each tracks/files is played.

When you find the track/file that you want to hear, press the INTRO

CHECK button again to resume normal playback.

< To skip to an earlier or later track/file, press a Skip button (. or

/).

< Press the INTRO CHECK button during ordinary playback to start

checking the beginnings of tracks/files from the currently playing

track/file.

< Repeat playback and shuffle playback cannot be used with the

intro check function. (The first 10seconds of each track/file cannot

be played back repeatedly or shuffled.)

< After the beginning of every track/file has been checked, playback

stops and the intro check mode is canceled.

< If one of the following buttons is pressed, intro check mode will be

cancelled:

Main unit

POWER button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button

Remote control unit

STANDBY/ON button, OPEN/CLOSE button (L), Stop button (H),

SHUFFLE button, INTRO CHECK button

Intro check

15

ENGLISH

Up to 32 tracks/files can be programmed in the desired order.

1

Press the PROGRAM button when playback is stopped.

MP3/WMA disc

CD

The MEMORY indicator appears, showing that program mode is

enabled.

< To stop programming, press the Stop button (H).

2

(When programming with an MP3/WMA disc)

Press the Number buttons to select a folder, then press

the PROGRAM button.

< You can also use the Skip buttons (.//) to select folders.

< MP3/WMA files not located in a specific folder are in the “01”

(ROOT) folder.

< You can also press the ENTER button to confirm a folder.

3

Press the Number buttons to select a track/file, then

press the PROGRAM button.

The track/file is programmed, and “P-02” is displayed.

< You can also use the Skip buttons (.//) to select tracks/

files.

< You can also press the ENTER button to confirm a song number.

< Repeat steps

2

and

3

to program more tracks/files.

< You can program up to 32 tracks/files.

< To stop programming, press the Stop button (H). Programming

is cancelled, but the program contents are retained in memory.

To restart program playback, press the PROGRAM button, and

then press the Play/Pause button (G/J).

4

When the selection of track/file numbers is completed,

press the Play/Pause button (

G

/

J

) to start program

playback.

< After program playback finishes, press the Play/Pause button

(y/J) to play the program again.

< Pressing the POWER button or the OPEN/CLOSE button (L)

causes the program content to be discarded.

< The shuffle function does not work during program playback.

< During program playback, tracks/files cannot be selected using

the Number buttons.

Program playback

16

Program playback (continued)

Adding tracks/files to the end of the program

In the stop mode, press the PROGRAM button repeatedly until

“00” appears on the display.

Press repeatedly

Select a track/file number using the Number buttons, and then

press the PROGRAM button.

< You can also use the Skip buttons (.//) to select track/file

numbers.

The track/file is added to the end of the program.

Overwriting part of the program

When playback is stopped, press the PROGRAM button repeatedly

until the program number to be changed appears on the

display.

Press repeatedly

Program number

to be changed

Select a track/file number using the Number buttons, and then

press the PROGRAM button.

< You can also use the Skip buttons (.//) to select track/file

numbers.

The newly selected track/file is added to the program.

17

ENGLISH

Checking the program order

Press repeatedly

When playback is stopped, press the PROGRAM button repeatedly.

The numbers of the programmed tracks/files and their program

numbers will be shown in order.

Clearing the program contents

When playback is stopped, press the stop (8) button to clear the

program contents.

The program contents are also cleared if one of the following

buttons is pressed.

Main unit

POWER button, OPEN/CLOSE button (L)

Remote control unit

STANDBY/ON button, OPEN/CLOSE button (L)

18

Search mode (MP3/WMA disc only)

You can search for, select and play files by name.

< If a file name uses Japanese, Chinese or other double-byte

characters, “ ” is displayed and the search function will

not work accurately.

Searching for the name of a file

1

Press and hold the DISPLAY button for at least one

second during playback or when stopped.

Press and

hold for

at least

1second

The SEARCH indicator blinks, and the first letter of the file name,

the file name and the file number are shown.

File name File number

First letter of le name

< Press the Stop button (H) to exit search mode. (This does not

stop playback when playing.)

< “

” appears when there is no information.

2

Select the first letter of the file you want to hear by

pressing the Skip buttons (

.

/

).

< Press / to search forward from A to Z and then 0 to 9, and

press . to search backward from 9 to 0 and then Z to A.

3

When you reach the letter that is the first letter of the file

that you want to hear, press the ENTER button to blink the

first letter.

4

Press the Skip buttons (.//) to search through the

files that start with the selected letter until you find the

file that you want to play.

< To return to selection of the first letter (as shown in the

illustration in step

1

), press the ENTER button again.

5

Press the Play/Pause button (

G

/

J

).

Playback starts from the selected file.

19

ENGLISH

Searching for a file in a folder

1

During playback or when stopped, press and hold the

DISPLAY button for at least one second to enter song

name search mode.

Press and

hold for

at least

1second

2

Press the DISPLAY button again.

The SEARCH and ALBUM indicators light and the folder name is

shown.

Folder name

Folder number

< Press the Stop button (H) to exit search mode. (This does not

stop playback when playing.)

< “ ” appears when there is no information.

3

Press the Skip buttons (

.

/

) to find the folder that

contains the file that you want to hear.

< Press / to search forward from A to Z and then 0 to 9, and

press . to search backward from 9 to 0 and then Z to A.

4

When you find the folder that contains the song you want

to hear, press the ENTER button.

The ALBUM indicator will disappear.

File name

< To return to selection of the folder (as shown in the illustration in

step

1

), press the ENTER button again.

5

Select the file in the folder by pressing the Skip buttons

(

.

/

).

< If you press the Play/Pause button (y/J) before selecting a file,

playback will start from the first file in the selected folder.

6

Press the Play/Pause button (

G

/

J

).

Playback starts from the selected file.

20

If you experience a problem with this unit, please check the following

items before requesting service. If it still does not operate correctly,

contact the retailer where you purchased the unit.

General

No power

e Check the connection to the AC power source. Confirm that the

AC source is not a switched outlet, and, if it is, that the switch is

turned on. Confirm that there is power to the AC outlet by plug-

ging another item such as a lamp or a fan into the outlet.

Remote control does not work

e Press the POWER switch of the main unit to turn it on.

e If the batteries are exhausted, change the batteries.

e Use the remote control within the effective range (16ft/5m)

and point it toward the remote sensor on the front panel.

e Make sure that there are no obstructions between the remote

control and the main unit (page 5).

e Turn off any fluorescent lights near the unit.

No sound

e Check the connection to the amplifier.

e Check the operation of the amplifier.

Will not play

e Load a disc with the label side up.

e If the disc is dirty, clean its surface.

e If a blank disc has been loaded, load a prerecorded disc.

e Depending on the disc and other factors, playback of some

CD-R/RW discs might not be possible. Try again with another

disc.

e You cannot play unfinalized CD-R/RW discs. Finalize such a disc

in a CD recorder and try again.

Sound skips

e Place the unit in a stable place to avoid vibrations and shocks.

e If the disc is dirty, clean its surface.

e Do not use scratched, damaged or warped discs.

WP3, WMA files

Playback is not possible.

e Check the file extension. Files are recognized by their exten-

sions: “.mp3” for MP3 files and “.wma” for WMA files.

e The MP3/WMA file might be damaged.

e Check the file format. This unit can play MP3 and WMA files

(page 7).

The names of tracks, artists and albums are not shown.

e There is no ID3 tag information for the music file. Use a com-

puter, for example, to prepare MP3/WMA files with corrected

ID3 tag information.

Some characters are not shown correctly.

e If the file information uses Japanese, Chinese or other double-

byte characters, playback is possible but the name will not be

shown correctly.

Since this device uses a microcontroller, external noise and

other interference can cause the unit to malfunction. If this

occurs, turn the power off and restart the operation after wait-

ing about a minute.

Beware of condensation

Condensation could occur when the unit (or a disc) is moved from

a cold to a warm place, or used after a sudden temperature change.

Vapor in the air could condense on the internal mechanisms, mak-

ing correct operation erratic or impossible. To prevent this, or if this

occurs, leave the unit for one or two hours with its power turned on.

The unit will stabilize at the temperature of its surroundings.

Maintenance

If the surface of the unit gets dirty, wipe it with a soft cloth or use

diluted mild liquid soap. Never spray liquid directly on this unit. Apply

cleaner to the cleaning cloth and wipe gently. Be certain to remove

any excess completely. Do not use thinner or alcohol as they could

damage the surface of the unit. Allow the surface of the unit to dry

completely before using.

About automatic power saving function

The unit will automatically enter standby if 30 minutes pass under

the conditions shown in the table below.

To reactivate the unit after it has entered standby automatically,

press a button on the main unit or the remote control. If pressing

the POWER button on the main unit, you must press it twice.

Status CD

No disc



Stopped/paused



Playing back -

 Automatic power saving function active

- Automatic power saving function active

Troubleshooting

La pagina si sta caricando...

TEAC CD-P1260MKII Manuale del proprietario

TEAC CD-P1260MKII Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti