Cisco 7606 Guida d'installazione

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco 7600 Series Router Module

Installation Guide

October 2010

Text Part Number: OL-5077-7

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required

to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not

installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to

comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital

devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television

communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its

peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits

controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR

IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, CCSI, Cisco Eos, Cisco Explorer, Cisco HealthPresence, Cisco IronPort, the Cisco logo, Cisco Nurse Connect, Cisco Pulse, Cisco SensorBase,

Cisco

StackPower, Cisco StadiumVision, Cisco TelePresence, Cisco TrustSec, Cisco Unified Computing System, Cisco WebEx, DCE, Flip Channels, Flip for Good, Flip

Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work,

Live, Play, and Learn, Cisco

Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks; and

Access Registrar, Aironet, AllTouch, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the

Cisco

Certified Internetwork Expert logo, Cisco IOS, Cisco Lumin, Cisco Nexus, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity,

Collaboration Without Limitation, Continuum, EtherFast, EtherSwitch, Event Center, Explorer, Follow Me Browsing, GainMaker, iLYNX, IOS, iPhone, IronPort, the

IronPort logo, Laser Link, LightStream, Linksys, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, PCNow, PIX, PowerKEY,

PowerPanels, PowerTV, PowerTV (Design), PowerVu, Prisma, ProConnect, ROSA, SenderBase, SMARTnet, Spectrum Expert, StackWise, WebEx, and the WebEx logo are

registered trademarks of Cisco and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (1002R)

3

Book Title

OL-5077-7

CONTENTS

Preface 7

Document Revision History 1-7

Audience 1-7

Organization 1-7

Conventions 1-8

Warning Definition 1-10

Related Documentation 1-13

Obtaining Documentation 1-13

Cisco.com 1-13

Documentation CD-ROM 1-13

Ordering Documentation 1-14

Documentation Feedback 1-14

Obtaining Technical Assistance 1-14

Cisco.com 1-14

Technical Assistance Center 1-15

Obtaining Additional Publications and Information 1-16

CHAPTER

1 Product Overview 1-1

Cisco 7600 Series Routers 1-1

Supported Hardware 1-1

Features 1-3

Supervisor Engines 1-4

LEDs 1-11

Reset Button 1-15

Console Port 1-15

Console Port Mode Switch 1-15

Switch Load Meter 1-16

PCMCIA Slot 1-16

Uplink Ports 1-16

Optical Services Modules 1-17

OC-3c POS OSM 1-17

OC-12c POS OSM 1-18

OC-48 POS OSM 1-18

OC-48 DPT/POS OSM 1-19

Contents

4

Book Title

OL-5077-7

Channelized OC-12 OSM 1-19

OC-12 ATM OSM 1-20

2+4-Port Gigabit Ethernet WAN OSM 1-20

12-Port Channelized T3 OSM 1-20

OSM LED Descriptions 1-21

Catalyst 6500 Family Modules 1-24

FlexWAN Module (WS-X6182-2PA) 1-24

Enhanced FlexWAN Module (WS-X6582-2PA) 1-25

48-Port 10/100TX Switching Module (WS-X6348-RJ-45) 1-26

16-Port Gigabit Ethernet Switching Module (WS-X6516-GBIC) 1-26

Switch Fabric Module (WS-C6500-SFM) 1-27

Switch Fabric Module 2 (WS-X6500-SFM2) 1-27

Cisco Application Control Engine (ACE) Module (ACE10-6500-K9) 1-28

Catalyst 6000 Family Module LED Descriptions 1-29

SPA Interface Processors 1-29

7600-SIP-200 1-30

7600-SIP-400 1-30

7600-SIP-600 1-31

SIP LED Descriptions 1-31

Ethernet Services 20G Line Cards 1-31

7600-ES20-10G 1-32

7600-ES20-GE 1-33

Cisco 7600 Ethernet Services Plus Line Cards 1-33

Cisco 7600 ES+ 2TG3C, -3CXL Line Cards 1-34

Cisco 7600 ES+ 4TG3C, -4TG3CXL Line Cards 1-34

Cisco 7600 ES+ 20G3C, -20G3CXL Line Cards 1-35

Cisco 7600 ES+ 40G3C, -40G3CXL Line Cards 1-36

Port Addresses 1-37

Physical Interface Addresses 1-37

MAC Addresses 1-38

Hot Swapping Supervisor Engines and Modules 1-39

Power Management and Environmental Monitoring 1-39

OSM Technology Overview 1-39

SONET/SDH Overview 1-40

ATM Overview 1-40

CHAPTER

2 Preparing for Installation 2-1

Safety Guidelines 2-1

General Precautions 2-1

Contents

5

Book Title

OL-5077-7

Safety Warnings 2-2

Installation Hazard 2-2

Blank Faceplates and Cover Panels 2-4

Backplane Voltage 2-6

SELV Circuit 2-7

Wrist Strap Warning 2-9

Limiting Connection Distances 2-10

Determining Cable Distances 2-10

Ethernet and Fast Ethernet Transmission Distances 2-11

OC-3, OC-12, and OC-48 POS Fiber Interface Specifications 2-11

ATM OC-12 Optical Specifications 2-12

Gigabit Ethernet Optical Specifications 2-13

Patch Cord 2-13

Differential Mode Delay 2-14

Supervisor Engine Console Port Cabling Specifications 2-16

Port Connector Requirements 2-16

Port Densities 2-18

Software Requirements 2-19

CHAPTER

3 Installing Modules 3-1

Required Tools 3-1

Preventing Electrostatic Discharge Damage 3-2

Installing a Supervisor Engine or a Module 3-2

Removing the Supervisor Engine or a Module 3-13

Connecting the Supervisor Engine 3-15

Connecting to the Console Port 3-15

Connecting to the Uplink Ports 3-16

Installing and Removing GBICs 3-17

GBIC Installation Guidelines 3-17

Installing a GBIC 3-18

Removing a GBIC 3-20

Using Flash PC Cards 3-20

Verifying the Installation 3-22

CHAPTER

4 Troubleshooting 4-1

Obtaining Technical Assistance 4-1

Troubleshooting Router Start Up Issues 4-1

Troubleshooting Router Booting Issues 4-4

Contents

6

Book Title

OL-5077-7

Troubleshooting Router Boot Failure from the Flash Memory 4-4

Troubleshooting Vector Errors When Booting from Flash Memory 4-4

Router Partially Boots from Flash and Displays Boot Prompt 4-17

Troubleshooting Router Freeze After the ROM Monitor Initializes 4-20

Troubleshooting Router Freeze in the ROM Monitor Mode 4-20

Troubleshooting Scrambled Output When Booting from ROM 4-21

Troubleshooting Local Timeouts When Booting from ROM 4-22

Troubleshooting Unresponsive Terminal Connection to Unconfigured Access Server 4-22

Technical Specifications A-1

Module Specifications A-1

Regulatory Standards Compliance A-2

Cable Specifications B-1

Interface Specifications B-1

Fiber-Optic Specifications B-1

Switching Module RJ-45 10/100BASE-TX Ports B-2

Supervisor Engine 2 Console Port Signals and Pinouts B-2

Console Port Mode Switch B-2

Identifying a Rollover Cable B-3

Console Port Mode 1 Signaling and Pinouts B-3

Console Port Mode 2 Signaling and Pinouts B-5

Upgrading the Memory on the OSM C-1

Safety C-1

Wrist Strap Warning C-1

Required Tools C-3

Upgrading the OSM Memory C-3

Removing the SODIMM C-4

Installing the New SODIMM C-5

I

NDEX

7

Book Title

OL-5077-7

Preface

This preface describes who should read the Cisco 7600 Series Router Module Installation Guide, how it

is organized, and its document conventions.

Document Revision History

Table 1 records changes to this document.

Audience

Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS3260) should install,

replace, or service the equipment described in this publication.

Organization

Table 2 lists the document organization of this guide.

Ta bl e 1 Document Revision History

Revision Date Change Summary

OL-5077-7 September 2010 • Added troubleshooting information in Chapter 4,

“Troubleshooting”.

OL-5077-6 October 2008 • Added ES+ line cards

OL-5077-5 February, 2007 • Added Route Switch Processor 720

• Added Ethernet Services 20G line cards

• Added Cisco Application Control Engine (ACE) module

OL-5077-4 December, 2005 • Added Supervisor Engine 32

OL-5077-3 April, 2005 • Added Cisco 7604 router

• Added Document Revision History table

8

Book Title

OL-5077-7

Preface

Conventions

Command descriptions use these conventions:

Screen examples use these conventions:

Ta bl e 2 Document Organization

Chapter Title Description

Chapter 1 Product Overview Provides an overview of the Cisco 7600 series routers,

the supervisor engines, the Optical Services Modules

(OSMs), the recommended Catalyst 6000 family

modules, and the SPA interface processors (SIPs).

Chapter 2 Preparing for

Installation

Describes how to prepare your site for installing the

supervisor engine, OSMs, recommended Catalyst

6000

family modules, and SIPs, and includes information on

ensuring safety during installing and preparing the

necessary cabling and interface connectors.

Chapter 3 Installing Modules Describes how to install the supervisor engine, OSMs,

recommended Catalyst

6000 family modules, and SIPs

in the Cisco

7600 series routers. Includes procedures to

verify the module operation after installation.

Appendix A Technical

Specifications

Lists the technical specifications for the OSMs,

recommended Catalyst 6000 family modules, and SIPs.

Appendix B Cable Specifications Lists the cable specifications for the OSMs,

recommended Catalyst 6000 family modules, and SIPs.

Appendix C Upgrading the

Memory on the OSM

Provides procedures for upgrading the memory on the

OSMs.

Ta bl e 3 Command Descriptions

boldface font Commands and keywords are in boldface.

italic font Arguments for which you supply values are in italics.

[ ] Elements in square brackets are optional.

{x | y | z} Alternative keywords are grouped in braces and separated

by vertical bars.

[x | y | z] Optional alternative keywords are grouped in brackets and

separated by vertical bars.

string A nonquoted set of characters. Do not use quotation marks

around the string or the string will include the quotation

marks.

9

Book Title

OL-5077-7

Preface

Conventions

Notes use the following conventions:

Tip Means the following information will help you solve a problem. The tip information may not be

troubleshooting or even an action, but could be helpful information.

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the

publication.

Cautions use the following conventions:

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Warnings use the following conventions:

screen font Terminal sessions and information the system displays are

in

screen font.

boldface screen

font

Information you must enter is in boldface screen font.

italic screen font Arguments for which you supply values are in italic

screen font.

^ The symbol ^ represents the key labeled Control—for

example, the key combination ^D in a screen display

means hold down the Control key while you press the D

key.

< > Nonprinting characters, such as passwords, are in angle

brackets.

[ ] Default responses to system prompts are in square

brackets.

<...output

truncated...>

This indicates that screen output not relevant to the

example was removed to save space and preserve clarity.

10

Book Title

OL-5077-7

Preface

Conventions

Warning Definition

Warning

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause

bodily injury. Before you work on any equipment, be aware of the hazards

involved with electrical circuitry and be familiar with standard practices for

preventing accidents. Use the statement number provided at the end of each

warning to locate its translation in the translated safety warnings that

accompanied this device.

Statement 1071

SAVE THESE INSTRUCTIONS

Waarschuwing

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat

werken, dient u zich bewust te zijn van de bij elektrische schakelingen

betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken

om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan

de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat

wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia

vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien

käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin

ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana

toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa

näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

Attention

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant de

travailler sur un équipement, soyez conscient des dangers liés aux circuits

électriques et familiarisez-vous avec les procédures couramment utilisées pour

éviter les accidents. Pour prendre connaissance des traductions des

avertissements figurant dans les consignes de sécurité traduites qui

accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la

fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

11

Book Title

OL-5077-7

Preface

Conventions

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den

Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung

vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen

Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

Avvertenza

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe

causare infortuni alle persone. Prima di intervenire su qualsiasi

apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti

elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per

individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

Advarsel

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade

på person. Før du begynner å arbeide med noe av utstyret, må du være

oppmerksom på farene forbundet med elektriske kretser, og kjenne til

standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver

advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som

fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

Aviso

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá

ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer

equipamento, tenha conhecimento dos perigos envolvidos no manuseio de

circuitos elétricos e familiarize-se com as práticas habituais de prevenção de

acidentes. Utilize o número da instrução fornecido ao final de cada aviso para

localizar sua tradução nos avisos de segurança traduzidos que acompanham

este dispositivo.

GUARDE ESTAS INSTRUÇÕES

¡Advertencia!

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física.

Antes de manipular cualquier equipo, considere los riesgos de la corriente

eléctrica y familiarícese con los procedimientos estándar de prevención de

accidentes. Al final de cada advertencia encontrará el número que le ayudará

a encontrar el texto traducido en el apartado de traducciones que acompaña a

este dispositivo.

GUARDE ESTAS INSTRUCCIONES

12

Book Title

OL-5077-7

Preface

Conventions

Varning!

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan

leda till personskada. Innan du utför arbete på någon utrustning måste du vara

medveten om farorna med elkretsar och känna till vanliga förfaranden för att

förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att

hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna

anordning.

SPARA DESSA ANVISNINGAR

13

Book Title

OL-5077-7

Preface

Related Documentation

For instructions on installing and configuring Cisco 7600 series routers, refer to these publications:

• Regulatory Compliance and Safety Information for Cisco 7600 Series Routers

• Cisco 7600 Series Router Installation Guide

• Cisco 7609 Router Installation Guide

• Cisco 7600 Series Cisco IOS Command Reference, 12.1E

• Cisco 7600 Series Cisco IOS System Message Guide, 12.1E

• Cisco 7600 Series Cisco IOS Software Configuration Guide, 12.1E

• Cisco 7600 Series Cisco IOS Command Reference, 12.2SX

• Cisco 7600 Series Cisco IOS System Message Guide, 12.2SX

• Cisco 7600 Series Cisco IOS Software Configuration Guide, 12.2SX

• Cisco 7600 Series Internet Router MIB Documentation

• Cisco 7600 Series Router SIP and SPA Hardware Installation Guide

• Cisco 7600 Series Router SIP and SPA Software Configuration Guide

Obtaining Documentation

Cisco provides several ways to obtain documentation, technical assistance, and other technical

resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation on the World Wide Web at this URL:

http://www.cisco.com/univercd/home/home.htm

You can access the Cisco website at this URL:

http://www.cisco.com

International Cisco web sites can be accessed from this URL:

http://www.cisco.com/public/countries_languages.shtml

Documentation CD-ROM

Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM

package, which may have shipped with your product. The Documentation CD-ROM is updated monthly

and may be more current than printed documentation. The CD-ROM package is available as a single unit

or through an annual subscription.

Registered Cisco.com users can order the Documentation CD-ROM (product number

DOC-CONDOCCD=) through the online Subscription Store:

http://www.cisco.com/go/subscription

14

Book Title

OL-5077-7

Preface

Obtaining Technical Assistance

Ordering Documentation

You can find instructions for ordering documentation at this URL:

http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm

You can order Cisco documentation in these ways:

• Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from

the Networking Products MarketPlace:

http://www.cisco.com/en/US/partner/ordering/index.shtml

• Registered Cisco.com users can order the Documentation CD-ROM (Customer Order Number

DOC-CONDOCCD=) through the online Subscription Store:

http://www.cisco.com/go/subscription

• Nonregistered Cisco.com users can order documentation through a local account representative by

calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408

526-7208 or, elsewhere

in North America, by calling 800

553-NETS (6387).

Documentation Feedback

You can submit comments electronically on Cisco.com. On the Cisco Documentation home page, click

Feedback at the top of the page.

You can e-mail your comments to bu[email protected].

You can submit your comments by mail by using the response card behind the front cover of your

document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com, which includes the Cisco Technical Assistance Center (TAC) Website, as a

starting point for all technical assistance. Customers and partners can obtain online documentation,

troubleshooting tips, and sample configurations from the Cisco TAC website. Cisco.com registered users

have complete access to the technical support resources on the Cisco TAC website, including TAC tools

and utilities.

Cisco.com

Cisco.com offers a suite of interactive, networked services that let you access Cisco information,

networking solutions, services, programs, and resources at any time, from anywhere in the world.

Cisco.com provides a broad range of features and services to help you with these tasks:

• Streamline business processes and improve productivity

• Resolve technical issues with online support

15

Book Title

OL-5077-7

Preface

Obtaining Technical Assistance

• Download and test software packages

• Order Cisco learning materials and merchandise

• Register for online skill assessment, training, and certification programs

To obtain customized information and service, you can self-register on Cisco.com at this URL:

http://www.cisco.com

Technical Assistance Center

The Cisco TAC is available to all customers who need technical assistance with a Cisco product,

technology, or solution. Two levels of support are available: the Cisco TAC website and the Cisco TAC

Escalation Center. The avenue of support that you choose depends on the priority of the problem and the

conditions stated in service contracts, when applicable.

We categorize Cisco TAC inquiries according to urgency:

• Priority level 4 (P4)—You need information or assistance concerning Cisco product capabilities,

product installation, or basic product configuration.

• Priority level 3 (P3)—Your network performance is degraded. Network functionality is noticeably

impaired, but most business operations continue.

• Priority level 2 (P2)—Your production network is severely degraded, affecting significant aspects

of business operations. No workaround is available.

• Priority level 1 (P1)—Your production network is down, and a critical impact to business operations

will occur if service is not restored quickly. No workaround is available.

Cisco TAC Website

You can use the Cisco TAC website to resolve P3 and P4 issues yourself, saving both cost and time. The

site provides around-the-clock access to online tools, knowledge bases, and software. To access the

Cisco TAC website, go to this URL:

http://www.cisco.com/tac

All customers, partners, and resellers who have a valid Cisco service contract have complete access to

the technical support resources on the Cisco TAC website. Some services on the Cisco TAC website

require a Cisco.com login ID and password. If you have a valid service contract but do not have a login

ID or password, go to this URL to register:

http://tools.cisco.com/RPF/register/register.do

If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco

TAC website, you can open a case online at this URL:

http://www.cisco.com/en/US/support/index.html

If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC

website so that you can describe the situation in your own words and attach any necessary files.

16

Book Title

OL-5077-7

Preface

Obtaining Additional Publications and Information

Cisco TAC Escalation Center

The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These

classifications are assigned when severe network degradation significantly impacts business operations.

When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer

automatically opens a case.

To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:

http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml

Before calling, please check with your network operations center to determine the level of Cisco support

services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network

Supported Accounts (NSA). When you call the center, please have available your service agreement

number and your product serial number.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online

and printed sources.

• The Cisco Product Catalog describes the networking products offered by Cisco Systems as well as

ordering and customer support services. Access the Cisco Product Catalog at this URL:

http://www.cisco.com/en/US/products/products_catalog_links_launch.html

• Cisco Press publishes a wide range of networking publications. Cisco suggests these titles for new

and experienced users: Internetworking Terms and Acronyms Dictionary, Internetworking

Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design

Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL:

http://www.ciscopress.com

• Packet magazine is the Cisco monthly periodical that provides industry professionals with the latest

information about the field of networking. You can access Packet magazine at this URL:

http://www.cisco.com/en/US/about/ac123/ac114/about_cisco_packet_magazine.html

• iQ Magazine is the Cisco monthly periodical that provides business leaders and decision makers

with the latest information about the networking industry. You can access iQ Magazine at this URL:

http://business.cisco.com/prod/tree.taf%3fasset_id=44699&public_view=true&kbns=1.html

• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering

professionals involved in the design, development, and operation of public and private internets and

intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_protocol_journal.html

• Training—Cisco offers world-class networking training, with current offerings in network training

listed at this URL:

http://www.cisco.com/en/US/learning/le31/learning_recommended_training_list.html

CHAPTER

1-1

Book Title

OL-5077-7

1

Product Overview

This chapter describes the Cisco 7600 series routers, supervisor engines, Optical Services Modules

(OSMs), recommended

Catalyst 6500 family modules, Ethernet Services 20G line cards, and SPA

interface processors (SIPs). It contains these sections:

• Cisco 7600 Series Routers, page 1-1

• Supervisor Engines, page 1-4

• Optical Services Modules, page 1-17

• Catalyst 6500 Family Modules, page 1-24

• SPA Interface Processors, page 1-29

• Ethernet Services 20G Line Cards, page 1-31

• Cisco 7600 Ethernet Services Plus Line Cards, page 1-33

• Hot Swapping Supervisor Engines and Modules, page 1-39

• Power Management and Environmental Monitoring, page 1-39

• OSM Technology Overview, page 1-39

Cisco 7600 Series Routers

The Cisco 7600 series routers consist of these routers:

• Cisco 7603 router (3 slots)

• Cisco 7604 router (4 slots)

• Cisco 7606 router (6 slots)

• Cisco 7609 router (9 vertical slots)

• Cisco 7609-S router (9 vertical slots)

• Cisco 7613 router (13 slots)

Cisco 7600 series routers provide optical WAN and MAN networking with a focus on line-rate delivery

of high-touch IP services at the edge of service provider networks.

Supported Hardware

The Cisco 7600 series routers support the following hardware:

1-2

Book Title

OL-5077-7

Chapter 1 Product Overview

Cisco 7600 Series Routers

• A supervisor engine with two modular Gigabit interface uplinks and an optional redundant

supervisor engine, in one of the following configurations:

–

Supervisor Engine 2, Policy Feature Card 2 (PFC2), and Multilayer Switch Feature Card 2

(MSFC2)

–

Supervisor Engine 2, PFC2, MSFC2, and Switch Fabric Module (SFM) or SFM2

–

Supervisor Engine 720, PFC3A, and MSFC3

–

Supervisor Engine 720 with PFC3B, and MSFC3

–

Supervisor Engine 720 with PFC3BXL, and MSFC3

–

Supervisor Engine 32 with PFC3B, and MSFC2A

–

Route Switch Processor 720 (RSP720), a PFC3C or PFC3CXL, and MSFC4

Note The supervisor engine and redundant supervisor engine must be completely identical.

Note The uplink ports are fully functional on the redundant supervisor engine in standby mode.

• Additional OSMs, recommended Catalyst 6000 family modules, and SIPs in any combination:

–

Two additional modules for the Cisco 7603 router

–

Three additional modules for the Cisco 7604 router

–

Five additional modules for the Cisco 7606 router

–

Eight additional modules for the Cisco 7609 router

–

Twelve additional modules for the Cisco 7613 router

• Hot-swappable fan assembly, redundant AC-input or DC-input power supplies, and modules

• Redundant AC-input or DC-input power entry modules (PEMs) (Cisco 7603 and 7606 routers only)

• Backplane that provides 32 Gbps of bandwidth; scalable up to 256 Gbps

• A Switch Fabric Module (WS-C6500-SFM or WS-X6500-SFM2):

–

Only the Supervisor Engine 2 supports the Switch Fabric Module.

–

Supervisor Engine 720 does not support the Switch Fabric Modules.

–

Either the WS-C6500-SFM or WS-X6500-SFM2 Switch Fabric Module can be installed in slot

5 of of the Cisco 7606 or Cisco

7609 router. A redundant Switch Fabric Module can be installed

in slot 6.

–

Only the WS-X6500-SFM2 Switch Fabric Module can be installed in slot 7 of the Cisco 7613

router. A redundant WS-X6500-SFM2 Switch Fabric Module can be installed in slot 8.

Note For redundancy, you can install a redundant Switch Fabric Module. The module that is installed first

functions as the primary module. When you install two Switch Fabric Modules at the same time, the

module in slot 5 or slot 7 acts as the primary module, and the module in slot 6 or slot 8 acts as the backup.

If you reset the module in slot 5 or slot 7, the module in slot 6 or slot 8 becomes the primary module.

Note The Switch Fabric Module is not supported on the Cisco 7603 router or the Cisco 7604 router.

1-3

Book Title

OL-5077-7

Chapter 1 Product Overview

Cisco 7600 Series Routers

Features

Table 1-1 lists some key features of the Cisco 7600 series router.

Ta bl e 1-1 Cisco 7600 Series Router Key Features

Feature Description

Performance and

configuration

Refer to the Cisco 7600 Series Cisco IOS Software Configuration Guide, 12.1E

or the Cisco 7600 Series Cisco IOS Software Configuration Guide, 12.2SX for

detailed information about the features supported on the Cisco

7600 series

routers.

Supervisor engine • Modular, upgradable feature modules for core switching logic

• Two modular Gigabit Ethernet ports supporting these GBIC

1

media types:

–

1000BASE-SX (WS-G5484)

–

1000BASE-LX/LH (WS-G5486)

–

1000BASE-ZX (WS-G5487)

• MSFC2 and PFC2 or PFC support

• MSFC3 and PFC3A or PFC3BXL support

• MSFC4 and PFC3C or PFC3CXL support

• PCMCIA slot

• Console port for terminal and modem access

Fault tolerance and

redundancy

• Support for two hot-swappable supervisor engines

• Fast switchover for redundant supervisor engine and modules

• Support for two redundant AC- or DC-input, load-sharing power supplies

• Support for two redundant AC- or DC-input PEMs (Cisco 7603 and 7606

routers only)

• Power management for modules and power supplies

• Environmental monitoring of critical system components

• Hot-swappable fan assembly

• Redundant clock modules

1-4

Book Title

OL-5077-7

Chapter 1 Product Overview

Supervisor Engines

This section describes the features on the Supervisor Engine 2, and Supervisor Engine 720. This section

contains the following topics:

• LEDs, page 1-11

• Console Port, page 1-15

• Console Port Mode Switch, page 1-15

• Switch Load Meter, page 1-16

• PCMCIA Slot, page 1-16

• Uplink Ports, page 1-16

Table 1-2 lists the supervisor engine configurations.

Memory

components

• 512-KB NVRAM stores configuration information.

• EEPROM

2

component on the supervisor engine stores module-specific

information, such as the module serial number, part number, controller type,

hardware revision, configuration information, and other details unique to

each module.

• 256-MB DRAM for the default system software.

• Bootflash—32-MB Flash memory stores the boot image.

• 16-MB Flash memory stores and runs software images.

• PC Flash—One slot for 16- and 24-MB Flash PC cards (cards optional).

Use

this additional Flash memory to store and run software images and

configuration files or to serve as an I/O device.

• Flash file system—Flash memory contains a file system. You can use a

variety of commands to manage the file system (such as cd, pwd, dir, and

delete). The file system includes the following devices:

–

Onboard bootflash

–

PC Flash slot

Component hot

swapping

All components (including the optional redundant supervisor engine and fans)

support hot swapping, which allows you to add, replace, or remove components

without interrupting the system power or causing other software or interfaces to

shut down.

Management • CLI through the console port or Telnet

• Simple Network Management Protocol

1. GBIC = Gigabit Interface Converter

2. EEPROM = electrically erasable programmable read-only memory

Table 1-1 Cisco 7600 Series Router Key Features (continued)

Feature Description

La pagina sta caricando ...

Cisco 7606 Guida d'installazione

Cisco 7606 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti