ProBoat UL-19 30" Hydroplane Brushless RTR Manuale utente

Marca: ProBoat

Modello: UL-19 30" Hydroplane Brushless RTR

Categoria: Giocattoli telecomandati

Tipo: Manuale utente

Owners Manual • Bedienungsanleitung

Manuel de l’utilisateur • Manuale dell’utente

PRB08028

UL 19 Hydroplane

INCH BRUSHLESS RTR

INCH READY

RUN BRUSHLESS BOAT

As the user of this product, you are solely responsible for

operating in a manner that does not endanger yourself

and others or result in damage to the product or the

property of others.

• When handling and/or transporting your boat, always

pick up the boat from the sides, keeping all moving

parts pointed away from you.

• Always keep a safe distance in all directions around

your model to avoid collisions or injury. This model

is controlled by a radio signal subject to interference

from many sources outside your control.

Interference can cause momentary loss of control.

• Always operate your model in open spaces away

from full-size vehicles, traffic and people.

• Always carefully follow the directions and warnings

for this and any optional support equipment

(chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything

electrical out of the reach of children.

• Always avoid water exposure to all equipment not

specifically designed and protected for this purpose.

Moisture causes damage to unprotected electronics.

• Never place any portion of the model in your mouth

as it could cause serious injury or even death.

• Never operate your model with low transmitter

batteries.

NOTICE

MEANING OF SPECIAL LANGUAGE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com or www.towerhobbies.com and click on the

support or resources tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no

possibility of injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires

some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or

damage to the product or other property. This product is not intended for use by children without direct adult supervision.

Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon

Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow

all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid

damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before

operating. Failure to operate the product correctly can result in damage to the product, personal property and

cause serious injury.

Table of Contents

Water-Resistant Boat with Waterproof Electronics ......... 3

General Precautions ........................................................ 3

Wet Conditions Maintenance .......................................... 3

Specifications .................................................................. 3

Recommended Tools and Materials ................................ 4

Battery Charger ............................................................... 4

Boat Stand Assembly ...................................................... 4

Antenna Tube Installation................................................. 4

Canopy Removal .............................................................. 5

Installing the Battery Packs ............................................. 5

Spektrum DX2E Radio System ........................................ 6

Battery Charger ............................................................... 6

Low Voltage Cutoff (LVC) ................................................. 7

Battery Chemistry ........................................................... 7

Getting Started ................................................................ 7

Control Check .................................................................. 8

Testing Your Boat in the Water ........................................ 8

Boating Tips ..................................................................... 9

When You Are Finished ................................................... 9

After Boating and Maintenance ......................................10

Binding .......................................................................10

Motor Care .................................................................10

Water Cooling System................................................11

Rudder Service ...........................................................11

Propeller Service ........................................................11

Propeller Strut Depth Adjustment ..............................11

Drivetrain Lubrication ................................................ 12

ESC Programming ..................................................... 12

Troubleshooting Guide ................................................... 13

Limited Warranty ........................................................... 14

Warranty and Service Contact Information ................... 15

FCC Information ............................................................ 15

IC Information ................................................................ 15

EU Compliance Statement ............................................ 15

Instructions for Disposal of WEEE ................................ 15

Replacement Parts ........................................................ 58

Recommended Parts ..................................................... 58

Optional Parts ................................................................ 59

Safety Precautions and Warnings

UL 19 Hydroplane

Your new Horizon Hobby boat has been designed and

built with a combination of waterproof and water-resistant

components to allow you to operate the product in calm,

fresh water conditions.

While the entire boat is highly water-resistant, it is

not completely waterproof and your boat should NOT

be treated like a submarine. The various electronic

components used in the boat, such as the servo(s)

and receiver are waterproof, however, most of the

mechanical components are water-resistant and require

additional maintenance after use.

Metal parts, including the bearings, pins, screws and nuts,

propeller, rudder, rudder mounts, prop struts, as well as

the contacts in the electrical cables, will be susceptible

to corrosion if additional maintenance is not performed

after running in wet conditions. To maximize the long-

term performance of your boat and to keep the warranty

intact, the procedures described in the “Wet Conditions

Maintenance” section must be performed regularly.

CAUTION: Failure to exercise caution while

using this product and complying with the

following precautions could result in product malfunction

and/or void the warranty.

Water-Resistant Boat with Waterproof Electronics

General Precautions

• Read the WET CONDITIONS MAINTENANCE

procedures and make sure that you have all the tools

you will need to properly maintain your boat.

• Not all batteries can be used in wet conditions.

Consult the battery manufacturer before use.

Caution should be taken when using Li-Po batteries

in wet conditions.

• Most transmitters are not water-resistant. Consult

your transmitter’s manual or the manufacturer

before operation.

• Never operate your transmitter or boat when

lightning is present.

• Salt water is very conductive and highly corrosive.

If you choose to run your boat in salt water,

immediately rinse the boat in fresh water after each

use. Operating your boat in salt water is at the sole

discretion of the modeler.

Wet Conditions Maintenance

• Drain any water that has collected in the hull by

removing the drain plug or canopy and tilting the

boat in the appropriate direction to drain the water.

CAUTION: Always keep hands, fingers, tools and

any loose or hanging objects away from rotating

parts.

• Remove the battery pack(s) and dry the contacts. If

you have an air compressor or a can of compressed

air, blow out any water that may be inside the

recessed connector housings.

• Remove all moving parts. Dry and lubricate parts

after every 30 minutes of operation or if the boat

becomes submerged.

NOTICE: Never use a pressure washer to clean your boat.

• Use an air compressor or a can of compressed air

to dry the boat and help remove any water that may

have gotten into small crevices or corners.

• Spray the bearings, fasteners and other metal parts

with a water-displacing light oil or lubricant.

• Let the boat air dry before you store it. Water (and

oil) may continue to drip for a few hours.

Specifications

Length 30 in (762mm)

Height 6 in (152.4mm)

Transmitter Spektrum™ SLT3 2.4GHz

Receiver Spektrum™ SR315 3-CH

DSMR

Hull Material Fiberglass

Motor 2000Kv 6-Pole 3650

Marine Motor (DYNM3831)

ESC 120A Brushless Marine ESC

2-6S (DYNM3875)

Servo 3KG, Plastic Gear Servo,

WP, 23T (SPMS603)

Tip: 4 AA batteries (sold separately) are required

to operate the transmitter.

6 in

(152.4mm)

30 in (762mm)

Antenna Tube Installation

1. Carefully feed the end of the receiver antenna through the grommet

inside the hull.

2. Pull the antenna wire out of the grommet toward the outside of the boat,

then slide the antenna through the antenna tube.

3. Insert the tube into the grommet, then fit the cap onto the tube.

4. Slide the clear 20mm waterproof sleeve over the grommet and hull and

install the tube into the sleeve.

The antenna must be installed above the boat's waterline to get the best

reception of your transmitter's signal.

NOTICE: Do not cut or kink the receiver antenna or damage may result.

Boat Stand Assembly

1. Attach the side stand pieces to the end pieces as

shown.

2. Use medium CA or epoxy adhesive to secure the

side stand to the ends.

3. Allow the adhesive to dry before placing your boat

on the stand.

INCH READY

RUN BRUSHLESS BOAT

Product Inspection

Carefully remove the boat and radio transmitter from the box.

Inspect the boat for damage. If your product is damaged, please

contact the hobby shop where you purchased your boat, or

contact Horizon Hobby Product Support. Refer to the Warranty

and Service Contact Information section for more info.

Recommended Tools and Materials

• Needle nose pliers

• Paper towel

• Rubbing alcohol

• Open-end wrench: 10mm (2)

• Nut driver: 4mm, 7mm, 8mm

• Phillips screwdriver: #1

• Hex wrench: 1.5mm, 2mm, 2.5mm, 3mm

• Clear tape (DYNM0102)

• Pro Boat

Marine Grease and Gun (DYNE4200)

• Hook and Loop Tape Set, WP 4pcs (DYNK0300)

Canopy Removal

1. Loosen the 4 screws located at each

corner of the canopy.

2. Remove the canopy from the hull

starting with the 2 rear screws. Ensure

that the 4 screws have disengaged

from their bases before carefully lifting

the canopy.

Installing the Battery Packs

The included electronics are rated for 2S–6S LiPo

batteries; however, running the stock propeller nonstop

on a 6S battery could overheat your electronics or

damage your batteries. If you run the stock propeller on

6S, we recommend using full throttle on straight line

passes only. Return passes should be at half throttle

to reduce the heat of the electronics. If you want to

run 6S nonstop, use optional propellers (PRB282006 or

PRB282027).

1. Install the 2 battery packs on the left and right

sides of the boat hull. Secure the batteries with the

included hook and loop straps. When running your

boat in rough water, use Waterproof Hook and Loop

Tape (DYNK0300) between the batteries and the

battery tray to secure the batteries more fully.

Tip: Start with the batteries as far forward as possible,

moving them 1/4 inch at a time toward the bow until

your boat reaches maximum speed.

2. Connect each battery pack to the ESC power

connectors.

The included propeller provides the best performance

between 4S (14.8V) and 5S LiPo (18.5V). 5S configuration

can be achieved by mounting a 3S LiPo battery

(DYNB3811EC) on the left side of the boat and a 2S LiPo

battery (DYNB3810EC) on the right side of the boat.

The added weight of the 3S battery on the left side will

counteract torque twist caused by the propeller spinning

at high RPM.

WARNING: When using 2 batteries in series, always

make sure they are in roughly the same condition

(age) and they have the same capacity (mAh) and

discharge rate (C rating). Failure to do so may cause

damage to your batteries, potentially causing a fire.

the

canopy

from

the

hull

ith the 2 rear screws. Ensure

screws

ave

nga

ged

bases before carefull

liftin

UL 19 Hydroplane

Factory Reset

There is a hidden mode if you want to reset the servo travel and calibration in the transmitter.

1. Hold full left and full brake while powering the transmitter ON to put the transmitter into programming mode.

The LED will flash 4 times then turns OFF to indicate factory reset.

2. Release the wheel and throttle trigger back to neutral and the LED will illuminate to indicate factory reset is

complete.

3. Power the transmitter OFF.

Transmitter Functions

This transmitter requires 4 AA batteries.

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

Installing the transmitter Batteries

CAUTION: If using rechargeable batteries, charge only rechargeable batteries. Charging non-rechargeable

batteries may cause the batteries to burst, resulting in injury to persons and/or damage to

property.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according

to national regulations.

A.A.

Speciﬁ cations

Power Supply: 4 AA Batteries

Operating Frequency: 2.4GHz

Transmit Power: <100mw

Control Protocol: SLT

Control: Proportional Steering and Throttle/Brake with Trim Knobs, Third Channel

with 3 Position Momentary Switch

Auxiliary Functions: 3 Position Throttle Limit Switch, Steering Rate Knob to

Change Steering Travel on-the-fly, Programmable Servo Travel for Steering and

Throttle/Brake

A. Throttle Trim

Adjusts the throttle neutral point

B. Steering Trim

Adjusts the steering center point. Normally, the steering trim is adjusted until the

vehicle tracks straight.

C. LED

• Solid red lights: Indicates the power is ON and adequate battery power

• Flashing red lights: Indicates the battery voltage is critically low. Replace

batteries

D. Steering Wheel

E. Throttle/Brake

F. Steering Rate

On-The-Fly knob for travel adjustment on the steering

G. Channel 3

3 position momentary switch, middle position is neutral

For programming press up for A button, press down for B button

H. Throttle Limit

Limits throttle output to 50/75/100%

Select 50% or 75% for less experienced drivers or when you are driving the

vehicle in a small area.

I. Throttle (TH) Servo Reversing

Move the switch to reverse the throttle channel

J. Steering (ST) Servo Reversing

Move the switch to reverse the steering channel

K. Power Button

INCH READY

RUN BRUSHLESS BOAT

Getting Started

1. Power on the transmitter.

2. Connect the two batteries to the

EC5

™

connectors on the ESC.

3. Power on the ESC switch. The

ESC arming tones will sound.

4. Test the transmitter’s control of

the boat with the boat on the

display stand.

Low Voltage Cutoff (LVC)

Discharging a Li-Po battery below 3V per cell may

damage your battery.The included ESC protects the boat

battery from over-discharge using Low Voltage Cutoff

(LVC). Before the battery charge decreases too much,

LVC removes power supplied to the motor. Power to

the motor pulses, showing that some battery power is

reserved for boat control and safe landing.

Disconnect and remove the Li-Po battery from the boat

after use to prevent trickle discharge. Charge your Li-Po

battery to about half capacity before storage. During

storage, make sure the battery charge does not fall below

3V per cell. LVC does not prevent the battery from over-

discharge during storage.

NOTICE: Repeated operation to LVC will damage the

battery.

Tip: Monitor your boat battery's voltage before and

after boating by using a Li-Po Cell Voltage Checker

(DYN4071, sold separately).

Battery Chemistry

The ESC comes from the factory in Li-Po Mode. To

change battery chemistry:

1. Keep the throttle at neutral and power ON the ESC.

2. Press and hold the Battery Chemistry Button on the

power switch for 3 seconds. The LED flashes the

current battery chemistry (red = Ni-MH or Ni-Cd;

green = Li-Po).

3. Continue holding the Battery Chemistry Button

for another 6 seconds. The ESC changes battery

chemistry and the LED flashes the new battery

chemistry.

4. Power OFF the ESC. The ESC saves the setting until

it is changed.

Battery Chemistry

Button

On/Off Switch

Choose a charger designed to charge the recommended

(2) Spektrum 7.4V 5000mAh 2S 100C Smart Hardcase

LiPo Battery: IC5 (SPMX50002S100H5), or (2) Spektrum

11.1V 5000mAh 3S 100C Smart Hardcase LiPo Battery:

IC5 (SPMX50003S100H5)We recommend the Spektrum

Smart S2100 AC Charger, 2x100W (SPMXC1010). Refer

to your charger manual for charging instructions and

safety information.

NOTICE: Never charge a battery in the boat or damage

may result.

Battery Charger

UL 19 Hydroplane

WARNING: Do not kink, cut or damage the antenna wire. The antenna is made of a coaxial wire; if the outer

sheath becomes damaged, the receiver will not work properly. If the antenna is damaged in any

way, replace the antenna before attempting to use the receiver.

SPMSR315 Dual Protocol Receiver

Speciﬁ cations

Type: Dual Protocol 3 Ch Receiver* (SLT/DSMR)

Dimensions (LxWxH): 32.5 x 21.5 x 12.4mm

Antenna Length: 90mm

Channels: 3

Weight: 6g

Band: 2.4GHz

Voltage Range: 3.5–9.6V

Bind Type: Bind Button

Failsafe: Hold the steering wheel and throttle trigger in the desired failsafe positions

during binding

*SPMSR315 receivers included with the SLT3 transmitter include SLT and DSMR

compatibility. If you have an SR315 receiver that was purchased by itself, you may need to

install a firmware update to make your SR315 SLT compatible.

STR THR

BATT

AUX 1

Receiver Antenna

The SR315 receivers feature a coaxial antenna design for easy installation in almost any model. Think of the last 1

inch (32mm) on the tip of the antenna as the active portion of the antenna, the coaxial portion leading up to it is just

an extension. Install the antenna so the active portion is positioned as high as possible in the vehicle, and not “in the

shadow” of any carbon fiber or metal. The case of the receiver can accept an antenna tube directly, making optimal

antenna placement easy (antenna tube not included).

Binding

Binding is the process of programming the receiver to

recognize the GUID (Globally Unique Identifier) code of

a single specific transmitter.

1. Press and hold the bind button, and Power ON the

receiver; the orange LED will begin to flash.

2. Set the trims and control positions at the desired

failsafe settings, and power ON the SLT3 transmitter.

3. When the orange LED on the SLT3 transmitter

remains lit, it is connected to SR315 receiver.

You must rebind when:

• Different failsafe positions are desired e.g., when

throttle or steering reversing has been changed.

Binding the receiver to a different transmitter.

Failsafe

In the unlikely event that the radio connection is lost

during use, the receiver will drive the servos to their pre-

programmed failsafe positions as set during Binding.

If the receiver is powered on before powering on the

transmitter, the receiver will enter this failsafe mode.

When the transmitter is powered on, normal control is

resumed.

IMPORTANT: Failsafe activates only in the event

that signal is lost from the transmitter. Failsafe will

NOT activate in the event that receiver battery power

decreases below the recommended minimums or

power to the receiver is lost.

Bind Button

INCH READY

RUN BRUSHLESS BOAT

Tip: Before placing your boat in the water, secure

the canopy on the hull. Apply clear tape (DYNM0102)

around the canopy seam, if desired.

1. Carefully place the boat in the water.

2. Operate the boat at slow speeds near the shoreline.

Avoid objects in the water at all times. When the

boat is moving forward, ensure water flows out of

the coolant outlet. Remove any blockage from the

rudder inlet and coolant system or the motor and ESC

(electronic speed control) may overheat.

3. Once you are comfortable operating the boat at slow

speeds, it is safe to operate the boat farther from the

shore.

4. If the boat does not go straight, adjust the steering

trim dial on the transmitter.

Tip: If you are using excessive steering trim on your

transmitter to make the boat drive straight, return the

trim to neutral and mechanically center the rudder. To

do this, use a 1.5mm hex driver to loosen the set screw

holding the push rod to the servo. Adjust the linkage in

or out of the brass barrel until the rudder is centered.

Tighten the set screw using a 1.5mm hex driver.

5. Bring the boat back to shore when you notice the

boat starting to lose speed.

6. Power off the ESC and disconnect the battery packs.

7. Allow the motor, ESC and battery packs to cool before

charging the batteries or operating the boat again.

NOTICE: Always power OFF the receiver before

powering OFF the transmitter. If the transmitter is

powered OFF before the receiver, the receiver will

enter failsafe mode.

Testing Your Boat in the Water

Control Check

IMPORTANT: Perform a control check at the beginning

of each boating session, after repair, or after installation

of new batteries.

Ensure the receiver antenna is extended properly and all

batteries are fully charged.

1. Power ON the transmitter and the boat. Do not

install the boat canopy.

2. Place the boat securely on the boat stand.

NOTICE: Do not operate the engine without water

cooling circulation or damage may result.

3. Check steering and throttle on the transmitter.

UL 19 Hydroplane

When running your boat for the first time, we

recommend calm wind and water conditions so that you

can learn how the boat responds to your control.

Maximum speeds are only achieved when the water

conditions are smooth and there is little wind. A sharp

turn, wind or waves can turn over a boat when it is

moving quickly. Always pilot your boat for the wind and

water conditions so that the boat does not turn over.

Consult local laws and ordinances before choosing a

location to pilot your boat.

Avoid boating near:

• watercraft

• people (swimming areas, fishing areas)

• stationary objects

• waves, wakes

• rapidly moving water

• wildlife

• floating debris

• overhanging trees

• vegetation

If the propeller and rudder are blocked with debris or

vegetation, remove the boat from the water and remove

the debris before continuing operation.

When making turns, decrease the throttle to reduce the

probability of flipping the boat over. If necessary, adjust

your steering input to decrease sensitivity.

Never operate your boat in less than 12 inches (30.5 cm)

of water.

If you need to retrieve your boat from the water, use

fishing equipment or another boat.

NOTICE: When running at full speed in choppy waters,

the prop may exit and re-enter the water repeatedly and

very quickly, subjecting the propeller and flex shaft to

some stress. Frequent stress may damage the propeller

and flex shaft.

CAUTION: Never operate your boat in extreme

temperatures or turbulent water.

CAUTION: Never attempt to retrieve a downed

boat by swimming.

Boating Tips

When You Are Finished

1. Power off the receiver.

2. Power off the transmitter.

3. Disconnect and remove the batteries

from the boat.

Tip: Always remove the canopy before

storage or moisture may allow mold and

mildew to grow in the boat.

INCH READY

RUN BRUSHLESS BOAT

• Drain water from inside the hull using the drain plug

• Fully dry the inside and outside of the boat, including

the water cooling lines and jacket around the motor.

Remove the hatch before storing your boat

• Repair any damage or wear to the boat

• Lubricate the flex shaft using Pro Boat Marine Grease

(DYNE4200)

• Make note of lessons learned from the trimming of

your boat, including water and wind conditions

Tip: The hook and loop strips in the boat retain water.

To dry them, press on them with a dry cloth.

NOTICE: When you are finished boating, never leave the

boat in direct sunlight or in a hot, enclosed area such as a

car. Doing so can damage the boat.

After Boating and Maintenance

Motor Care

• Prolong motor life by preventing overheating

conditions. Undue motor wear results from frequent

turns, stops and starts, pushing objects, boating in

rough water or vegetation and boating continuously at

high speed.

• Over-temperature protection is installed on the ESC to

prevent circuit damage, but cannot protect the motor

from excessive physical resistance.

Water Cooling System

If water does not stream out of the water outlets

while the boat is moving forward, immediately

return the boat to shore and clean any obstructions

or remove kinks from the water cooling lines/

system.

1. Disassemble and clean the water cooling system

to remove blockage and prevent overheating.

2. Replace damaged parts.

UL 19 Hydroplane

Rudder Service

1. Disconnect the water tube from the rudder.

2. Remove the nut, screw and linkage from the rudder

arm.

3. Turn the rudder and loosen the set screw from

the rudder pin.

4. Turn over the boat and lightly tap the rudder to

remove the pin.

5. Assemble in reverse order.

Propeller Service

1. Use an 8mm nut driver (DYN2805) to loosen the

nut from the driveshaft. To secure the propeller

while loosening the nut, hold the propeller.

2. Remove the nut and propeller from the driveshaft.

3. Assemble in reverse order. Correctly align the

propeller with the drive dog on the driveshaft.

Propeller Strut Depth Adjustment

Raising the propeller strut increases speed but

decreases handling.

Lowering the propeller strut increases stability but

decreases speed.

1. Use a 3 mm hex driver and 7mm open-end wrench

to loosen the propeller strut bolt.

2. Slide the strut up or down to change the angle of

the propeller in relation to the hull.

3. Once desired strut depth is achieved, tighten the

nuts and bolts.

INCH READY

RUN BRUSHLESS BOAT

Drivetrain Lubrication

Always replace the drivetrain parts when they are

damaged or show visible wear or injury and damage may

result.

Lubricating the flex shaft is vital to the life of the

drivetrain. The lubricant also acts as a water seal, keeping

water from entering the hull through the stuffing tube.

Lubricate the flex shaft and propeller strut after every 30

minutes of operation and/or everytime you change the

batteries.

1. Inside the hull, use 2 10mm open-end wrenches to

loosen the collet nut from the flex shaft.

2. Slide the flex shaft out from the stuffing tube and

drive strut at the rear of the boat.

Tip: Use paper or cloth to touch the flex shaft and other

lubricated parts.

3. Wipe the old lubricant and material from the flex

shaft.

Tip: Use motor spray (DYN5500) to break down the

grease buildup.

4. Lubricate the full length of the flex shaft assembly

up to the drive dog using Pro Boat Marine Grease

(DYNE4200). Also apply grease to the collet threads.

5. Carefully reinstall the flex shaft in the drive strut,

stuffing tube and collet. If the flex shaft is difficult to

remove from (or install into) the collet, rotate the flex

shaft to the right while pulling it from (or inserting it

into) the collet.

NOTICE: Do not rotate the flex shaft to the left inside

the coupler.

Ensure there is a 2mm gap between the drive strut and

drive dog to allow for flex shaft shrinkage under load.

NOTICE: Running the boat in saltwater could cause some

parts to corrode. If you run the boat in saltwater, rinse it

thoroughly in freshwater after each use and lubricate the

drive system.

NOTICE: Because of its corrosive effects, running RC

boats in saltwater is at the discretion of the modeler.

1. Pull and hold the Throttle Trigger to full throttle and

turn the ESC on.

2. After 2 seconds a “-B-B” will sound. Wait another

5 seconds and the ESC will give a rising tone to

indicate you have entered Programming Mode.

3. After entering Programming Mode, you will hear 4

tones in a loop indicating Programmable Items. Push

the Throttle Trigger to full brake within 3 seconds

after the tone sounds matching the programmable

item you want to select.

4. After selecting a programmable item, you will hear

several tones in a loop indicating Programmable

Values. Pull Throttle Trigger to full throttle to select

the value matching the tone. The ESC will give an

alternating tone to indicate the item is selected.

5. Keep the trigger in Full Throttle to return to Step 3

and continue item selection. Move the throttle stick

to full brake position within 2 seconds to exit the

Program Mode.

The black-shaded setting is the factory default

Programmable Items

Programmable Value -B Single Beep B–– Long Beep

-B -B-B -B-B-B -B-B-B-B B––

B––

-B

B––

-B-B

B––

-B-B-B

Running Mode -B

Forward

Only

Forward/

Backward

Li-Po Cells -B-B

Auto

Calc.

2s 3s 4s 5s 6s

Low Voltage Cutoff

-B-B-B

None 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

Timing -B-B-B-B 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º

ESC Programing

UL 19 Hydroplane

Problem Possible Cause Solution

Boat will not respond

to throttle but responds

to other controls

Throttle channel is reversed Reverse throttle channel on transmitter

Extra noise or extra

vibration

Damaged propeller, shaft or motor Replace damaged parts

Propeller is out of balance Balance or replace propeller

Reduced runtime or boat

underpowered

Boat battery charge is low Completely recharge battery

Boat battery is damaged Replace boat battery and follow battery instructions

Blocking or friction on shaft or propeller Disassemble, lubricate and correctly align parts

Boat conditions may be too cold

Make sure the battery is warm (above 10º C

[50º F]) before use

Battery capacity may be too low for conditions Replace battery or use a larger capacity battery

Too little lubrication on driveshaft Fully lubricate driveshaft

Vegetation or other obstacles block

the propeller

Remove vegetation or obstacles from propeller

Boat will not Bind

(during binding) to

transmitter

Transmitter is too near boat during binding

process

Move powered transmitter a few feet from boat,

disconnect and reconnect battery to boat

Boat or transmitter is too close to large

metal object, wireless source or another

transmitter

Move the boat and transmitter to another location

and attempt binding again

Another compatible transmitter in bind

mode within range of the receiver

Power off all compatible transmitters except the one

you are trying to bind

Boat battery/transmitter battery charge is

too low

Replace/recharge batteries

ESC switch is off Power on ESC switch

Boat will not connect

(after binding) to

transmitter

Transmitter is too near boat during

connecting process

Move powered transmitter a few feet from boat,

disconnect and reconnect battery to boat

Boat or transmitter is too close to large

metal object, wireless source or another

transmitter

Move boat or transmitter to another location and

attempt to connect again

Boat battery/transmitter battery charge is

too low

Replace/recharge batteries

ESC switch is off Power on ESC switch

Boat tends to dive in the

water or takes on water

The boat hull is not completely closed

Dry out the boat and ensure the hatch is fully closed

on the hull before returning the boat

to the water

Center of gravity is too far forward Move batteries back in the hull

Controls reversed Transmitter settings are reversed

Do the Control Direction Test and adjust controls on

transmitter appropriately

Motor overheats Blocked water cooler lines Clean, unkink or replace water lines

Motor power pulses

then motor loses power

ESC uses default soft Low Voltage Cutoff

(LVC)

Recharge boat battery or replace battery that is no

longer performing

Weather conditions might be too cold Postpone until weather is warmer

Battery is old, worn out or damaged Replace battery

Boat moves forward or

backward without input

from user

Throttle trim on transmitter not centered Adjust throttle trim to center (12 o'clock)

Boat does not drive

straight

Steering trim on transmitter not centered Adjust steering trim so vehicle drives straight

No steering or lack of

steering

Steering rate not adjusted correctly

Adjusts steering rate (ST RATE) knob on

transmitter to desired steering throw

Servo failed Contact Horizon Product Support

No throttle or lack of

throttle

ESC failed Contact Horizon Product Support

Motor failed Contact Horizon Product Support

ESC emits a continues

tone when powered on

Throttle trim not centered Center throttle trim on transmitter

Troubleshooting Guide

INCH READY

RUN BRUSHLESS BOAT

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original

purchaser that the product purchased (the “Product”) will be

free from defects in materials and workmanship at the date

of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i)

cosmetic damage, (ii) damage due to acts of God, accident,

misuse, abuse, negligence, commercial use, or due to

improper use, installation, operation or maintenance, (iii)

modification of or to any part of the Product, (iv) attempted

service by anyone other than a Horizon Hobby authorized

service center, (v) Product not purchased from an authorized

Horizon dealer, or (vi) Product not compliant with applicable

technical regulations or (vii) use that violates any applicable

laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON

MAKES NO OTHER WARRANTY OR REPRESENTATION,

AND HEREBY DISCLAIMS ANY AND ALL IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION,

THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. THE PURCHASER ACKNOWLEDGES THAT

THEY ALONE HAVE DETERMINED THAT THE PRODUCT

WILL SUITABLY MEET THE REQUIREMENTS OF THE

PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive

remedy shall be that Horizon will, at its option, either (i)

service, or (ii) replace, any Product determined by Horizon to

be defective. Horizon reserves the right to inspect any and all

Product(s) involved in a warranty claim. Service or replacement

decisions are at the sole discretion of Horizon. Proof of

purchase is required for all warranty claims. SERVICE OR

REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS

THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL,

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL

LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH

CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY

OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES. Further, in

no event shall the liability of Horizon exceed the individual

price of the Product on which liability is asserted. As Horizon

has no control over use, setup, final assembly, modification

or misuse, no liability shall be assumed nor accepted for

any resulting damage or injury. By the act of use, setup or

assembly, the user accepts all resulting liability. If you as

the purchaser or user are not prepared to accept the liability

associated with the use of the Product, purchaser is advised

to return the Product immediately in new and unused

condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to

conflict of law principals). This warranty gives you specific

legal rights, and you may also have other rights which vary

from state to state. Horizon reserves the right to change or

modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide

warranty support or service. Once assembly, setup or use of

the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to

better answer your questions and service you in the event that

you may need any assistance. For questions or assistance,

please visit our website at www.horizonhobby.com, submit a

Product Support Inquiry, or call the toll free telephone number

referenced in the Warranty and Service Contact Information

section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in,

please use the Horizon Online Service Request submission

process found on our website or call Horizon to obtain a

Return Merchandise Authorization (RMA) number. Pack

the Product securely using a shipping carton. Please note

that original boxes may be included, but are not designed to

withstand the rigors of shipping without additional protection.

Ship via a carrier that provides tracking and insurance for

lost or damaged parcels, as Horizon is not responsible for

merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.

horizonhobby.com/content/service-center_render-service-

center. If you do not have internet access, please contact

Horizon Product Support to obtain a RMA number along with

instructions for submitting your product for service. When

calling Horizon, you will be asked to provide your complete

name, street address, email address and phone number

where you can be reached during business hours. When

sending product into Horizon, please include your RMA

number, a list of the included items, and a brief summary

of the problem. A copy of your original sales receipt must

be included for warranty consideration. Be sure your name,

address, and RMA number are clearly written on the outside

of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you

have any issue with a Li-Po battery, please contact the

appropriate Horizon Product Support office.

Warranty Requirements

For Warranty consideration, you must include your original

sales receipt verifying the proof-of-purchase date. Provided

warranty conditions have been met, your Product will be

serviced or replaced free of charge. Service or replacement

decisions are at the sole discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service

will be completed and payment will be required without

notification or estimate of the expense unless the expense

exceeds 50% of the retail purchase cost. By submitting

the item for service you are agreeing to payment of the

service without notification. Service estimates are available

upon request. You must include this request with your item

submitted for service. Non-warranty service estimates will

be billed a minimum of ½ hour of labor. In addition you will

be billed for return freight. Horizon accepts money orders

and cashier’s checks, as well as Visa, MasterCard, American

Express, and Discover cards. By submitting any item to

Horizon for service, you are agreeing to Horizon’s Terms and

Conditions found on our website http://www.horizonhobby.

com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product

compliant in the country of use and ownership.

If received, a non-compliant Product will not be

serviced. Further, the sender will be responsible

for arranging return shipment of the un-serviced

Product, through a carrier of the sender’s choice

and at the sender’s expense. Horizon will hold

non-compliant Product for a period of 60 days from

notification, after which it will be discarded.

10/15

UL 19 Hydroplane

Warranty and Service Contact Information

FCC Information:

FCC ID: BRWSPMSLT300

FCC ID: BRWSRIRVINGV1

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modifications not expressly approved by

the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment gener-

ates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

IC Information

IC: 6157A-SPMSLT300

IC: 6157A-SRIRVINGV1

CAN ICES-3 (B)/NMB-3(B)

This device contains license-exempt transmitter(s)/receivers(s) that

comply with Innovation, Science, and Economic Development Canada’s

license-exempt RSS(s). Operation is subject to the following 2 conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

EU Compliance Statement: Hereby, Horizon Hobby, LLC

declares that the device is in compliance with the following:

EU Radio Equipment Directive 2014/53/EU;

RoHS 2 Directive 2011/65/EU

RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863

The full text of the EU declaration of conformity is available at the follow-

ing internet address: https://www.horizonhobby.com/content/support-

render-compliance.

Wireless Frequency Range and Wireless Output Power

SLT3 Transmitter

Max EIRP:16.3

Frequency Range:2403-2480MHz

SR315 Receiver

Max EIRP: -1.33dBm

Frequency Range: 2404-2476MHz

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European

Directive 2012/19/EU concerning waste of electrical and

electronic equipment (WEEE). This label indicates that this product should

not be disposed of with household waste. It should be deposited at an

appropriate facility to enable recovery and recycling.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure to maintain

a separation distance of at least 5 cm between your body (excluding

ﬁ ngers, hands, wrists, ankles and feet) and the antenna to meet RF

exposure safety requirements as determined by FCC regulations.

The following illustrations show the approximate 5 cm RF exposure

area and typical hand placement

when operating your Spektrum

transmitter.

Country of

Purchase

Horizon Hobby Phone Number/Email Address Address

North America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

2904 Research Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

European Union

Horizon Technischer Service service@horizonhobby.eu

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH +49 (0) 4121 2655 100

INCH READY

RUN BRUSHLESS BOAT

UL 19 Hydroplane

Als Benutzer dieses Produkts sind Sie allein dafür

verantwortlich, es so zu betreiben, dass es Sie selbst und

andere nicht gefährdet und dass es zu keiner Beschädigung

des Produkts oder des Eigentums Dritter kommt.

• Fassen Sie beim Handling oder Transport das Boot

immer von seiten an und halten alle bewegliche Teile

weg vom Körper.

• Halten Sie stets in allen Richtungen einen

Sicherheitsabstand um Ihr Modell, um Zusammenstöße

oder Verletzungen zu vermeiden. Dieses Modell wird

von einem Funksignal gesteuert, das Interferenzen

von vielen Quellen außerhalb Ihres Einflussbereichs

unterliegt. Diese Interferenzen können einen kurzzeitigen

Steuerungsverlust verursachen.

• Betreiben Sie Ihr Modell immer auf einer Freifläche ohne

Fahrzeuge in voller Größe, Verkehr oder Menschen.

• Befolgen Sie stets sorgfältig die Anweisungen und

Warnhinweise für das Modell und jegliche optionalen

Hilfsgeräte (Ladegeräte, Akkupacks usw.).

• Bewahren Sie alle Chemikalien, Klein- und Elektroteile

stets außerhalb der Reichweite von Kindern auf.

• Setzen Sie Geräte, die für diesen Zweck nicht speziell

ausgelegt und geschützt sind, niemals Wasser aus.

Feuchtigkeit kann die Elektronik beschädigen.

• Stecken Sie keinen Teil des Modells in den Mund,

da dies zu schweren Verletzungen oder sogar zum Tod

führen kann.

• Betreiben Sie Ihr Modell nie mit fast leeren Senderakkus.

Zusätzliche Sicherheitsvorkehrungen und Warnhinweise

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen

Sachwerten führen. Versuchen Sie nicht ohne Genehmigung durch Horizon Hobby, LLC, das Produkt zu zerlegen, es

mit inkompatiblen Komponenten zu verwenden oder auf jegliche Weise zu erweitern. Diese Bedienungsanleitung

enthält Anweisungen für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau,

Einrichtung oder Verwendung alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit

es estimmungsgemäß betrieben werden kann und Schäden oder schwere Verletzungen vermieden werden.

HINWEIS

SPEZIELLE BEDEUTUNGEN

Allen Anweisungen, Garantien und anderen zugehörigen Dokumenten sind Änderungen nach Ermessen von

Horizon Hobby, LLC vorbehalten. Aktuelle Produktliteratur ﬁ nden Sie unter www.horizonhobby.com oder www.

towerhobbies.com im Support-Abschnitt für das Produkt.

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe Gefahrenrisiken

beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den

Produktfunktionen vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am

Produkt oder persönlichem Eigentum führen oder schwere Verletzungen verursachen.

Altersempfehlung: Nicht für Kinder unter 14 Jahren. Dies ist kein Spielzeug.

Inhaltsverzeichnis

Spritzwassergeschützes Boot mit wasserdichter

Elektronik .............................................................................. 17

Allgemeine Sicherheitshinweise .............................................. 17

Wartungsanleitung nach Einsatz in feuchter Umgebung ...... 17

Spezifkationen ........................................................................... 17

Erforderliches Werkzeug und Materialien ............................... 18

Montage des Bootständers ..................................................... 18

Montage des Antennenröhrchen ............................................ 18

Abnehmen der Kabinenhaube ................................................. 19

Einsetzen der Akkupacks ......................................................... 19

Spektrum DX2E RC System ....................................................20

Einsetzen der Senderbatterien ................................................ 20

Akku Ladegerät .........................................................................20

Niederspannungsabschaltung (LVC) ........................................21

Akkutyp Wählen ........................................................................21

Starten ....................................................................................... 21

Kontrolle .....................................................................................22

Testen des Bootes im Wasser .................................................22

Tipps zum Fahren .....................................................................23

Nach dem Fahren ..................................................................... 23

Wartungsarbeiten nach dem Fahren ....................................... 24

Binden ...................................................................................24

Motorpflege ..........................................................................24

Kühlwassersystem ...............................................................25

Wartung des Ruders ............................................................ 25

Propellerwartung ..................................................................25

Tiefeneinstellung der Propellerstrebe ................................. 25

Fetten der Welle ...................................................................25

Regler-Programmierung .......................................................25

Problemlösung .......................................................................... 25

Garantie und Service Informationen .......................................26

Garantie und Service Kontaktinformationen ...........................27

EU Konformitätserklärung ........................................................27

Entsorgung in der Europäischen Union ..................................27

Ersatzteile .................................................................................. 58

Empfohlene Teile .......................................................................58

Diverse Teile ...............................................................................59

INCH READY

RUN BRUSHLESS BOAT

Ihr neues Horizon Hobby Boot wurde mit

einer Kombination von wasserdichten und

spritzwassergeschützten Komponenten entwickelt die es

ihnen ermöglichen das Modell bei ruhigen Bedingungen

in Süßwasser zu betreiben.

Obwohl das Boot spritzwassergeschützt ist es nicht

vollständig wasserdicht und darf keines Falls wie

ein U-Boot behandelt werden. Die verschiedenen

elektronischen Komponenten wie der Regler, die

Servos ubd der Empfänger sind wasserdicht, die

meisten mechanische Komponenten sind aber nur

spritzwassergeschützt und erfordern nach Betrieb

zusätzliche Wartung.

Metallteile, inklusive der Lager, Schrauben und Muttern,

Propeller, Ruder, Ruderhalter und Propellerstrebe sowie

die Kontakte in den elektrischen Kabeln sind anfällig für

Korrosion wenn nach dem Einsatz in feuchter Umgebung

zusätzliche Wartungsarbeiten nicht durchgeführt werden.

Um die Langzeitleistung ihres Bootes zu maximieren

und die Garantie aufrecht zu halten müssen diese

Wartungsarbeiten regelmäßig durchführen.

ACHTUNG: Unaufmerksamkeit während des

Betriebes des Produktes in Zusammenhang mit den

folgenden Sicherheitshinweisen kann zu Fehlfunktionen

und dem Verlust der Garantie führen.

Spritzwassergeschützes Boot mit wasserdichter Elektronik

Allgemeine Sicherheitshinweise

• Bitte lesen Sie sich die Wartungsanleitung sorgfältig

durch und stellen sicher, dass Sie alle Werkzeuge für

eine Wartung des Bootes haben.

• Nicht alle Akkutypen sind für den Einsatz in feuchter

Umgebung geeignet. Fragen Sie dazu vor dem Einsatz

den Hersteller des Akkus. Besondere Aufmerksamkeit

sollten Sie bei dem Einsatz von LiPo Akkus wallten

lassen.

• Die meisten Sender sind nicht wasserfest.

Sehen Sie bitte dazu vor Inbetriebnahme in der

Bedienungsanleitung ihres Senders nach oder

kontaktieren Sie den Hersteller.

• Betreiben Sie ihr Boot niemals bei Gewitter.

• Nehmen Sie niemals den Sender bei Blitzen oder

Gewitter in Betrieb.

Wartungsanleitung nach Einsatz

in feuchter Umgebung

• Nehmen Sie die Kabinenhaube und Ablaufstopfen

ab und kippen das Boot in die Richtung des

Ablauf bis alles Wasser was sich gesammelt hat

abgelaufen ist.

ACHTUNG: Halten Sie immer Hände, Finger,

Werkzeuge oder anderen lose, hängende Objekte

weg von drehenden Teilen wenn Sie das Boot trocknen.

• Entnehmen Sie den Akkupack und trockenen

die Kontakte. Sollten Sie einen Kompressor oder

Druckluftflasche zur Hand haben blasen Sie damit

das Wasser aus den Gehäusevertiefungen.

• Entfernen Sie alle beweglichen Teile. Trocknen und

schmieren Sie die Teile alle 30 Betriebsminuten

oder immer dann wenn das Boot ein- oder

untergetaucht war.

HINWEIS: Verwenden Sie keinen Hochdruckreiniger um

das Fahrzeug zu reinigen.

• Reinigen Sie das Fahrzeug mit Druckluft aus einem

Kompressor oder einer Druckluftflasche und entfernen

so das Wasser aus den Spalten und Ecken.

• Sprühen Sie die Lager, Wellen, Befestigungen

mit WD-40 Öl oder einem vergleichbaren

wasserverdrängenden Leichtöl ein.

• Lassen Sie das Fahrzeug vor dem Einlagern

vollständig trocknen. Das Abtropfen von Wasser

(und Öl) kann durchaus ein paar Stunden dauern.

Spezifkationen

Länge 762mm

Höhe 152.4mm

Sender Spektrum™ SLT3™ 2.4GHz

Empfänger Spektrum SR315 3-CH DSMR®

Marine

Rumpfmateral Glasfaser

Motor 3650 6-poliger Bootsmotor

2000 kV (DYNM3831)

ESC 120A Bootsempfänger 2-6

(DYNM3875)

Servo Plastikgetriebe Servo 3kg,

wasserdicht, 23T

Tipp: 4 AA Batterien oder Akkus (separat erhältlich)

werden zum Betrieb des empfänger.

152.4mm

762mm

Montage des Antennenröhrchen

1. Führen Sie vorsichtig das Ende der Antenne durch die Durchführung

im Rumpfinneren.

2. Ziehen Sie das Antennenkabel nach außen durch die Durchführung

und schieben dann die Antenne in das Röhrchen.

3. Stecken Sie das Röhrchen in die Durchführung und den Stopfen oben

auf das Röhrchen.

4. Ziehen Sie die durchsichtige 20 mm starke Manschette über

Durchführung und Rumpf und setzen Sie den Schlauch in die

Manschette ein.

Die Antenne muss über der Wasserlinie des Bootes installiert werden,

um den bestmöglichen Empfang für Ihr Sendersignal zu gewährleisten.

HINWEIS: Kürzen oder knicken Sie die Antennen nicht, da sonst die

Gefahr von Beschädigungen besteht.

Montage des Bootständers

1. Stecken Sie die Reiter der Seitenteile in die Schlitze

der Endteile. Die Schrift auf den Seitenteilen sollte

nach aussen zeigen.

2. Kleben Sie die Teile des Bootständers zusammen

wenn dieser auf einer ebenen Oberfläche steht.

3. Lassen Sie den Kleber vollständig trocknen bevor

Sie das Boot auf den Ständer stellen.

UL 19 Hydroplane

Produktüberprüfung

Entnehmen Sie vorsichtig das Boot und den Sender der

Box. Überprüfen Sie das Boot auf evtl. Schäden. Sollten

Sie Schäden feststellen kontaktieren Sie den Händler

bei dem Sie das Boot gekauft haben, oder den Product

Support kontaktieren. Siehe den Abschnitt zu Garantie und

Kundendienstinformationen zu weiteren Informationen.

Erforderliches Werkzeug und Materialien

• Spitzzange

• Papiertücher

• Reinigungsalkohol

• Maulschlüssel: 10mm (2)

• Steckschlüssel 4mm, 7mm, 8mm

• Phillips Schraubendreher: #1

• Inbusschlüssel: 1.5mm, 2mm 2,5mm, 3mm

• Transparentes Klebeband (DYNM0102)

• Pro Boat Marine Fett und Applikator (DYNE4200)

• Klettpads WP 4 Stk. (DYNK0300)

Abnehmen der Kabinenhaube

1. Lösen Sie die vier Schrauben an den Seiten

der Kabinenhaube.

2. Entfernen Sie die Kabinenhaube vom

Rumpf beginnend mit den beiden hinteren

Schrauben. Bitte achten Sie darauf, dass alle

vier Schrauben gelöst sein müssen bevor

Sie die Kabinenhaube vorsichtig anheben

könneny.

Kab

aube

mit den beiden hinteren

chten

ie darauf, dass alle

öst sein müssen bevor

be vorsichtig anheben

Einsetzen der Akkupacks

Die mitgelieferte Elektronik ist für die 2S-6S LiPo-Akkus

bewertet. Jedoch führt der ununterbrochene Betrieb des

Bestandpropellers auf einem 6S Akku zum Überhitzen

der Elektronik oder zu Schäden an den Akkus. Wird der

Bestandpropeller auf einem 6S Akku betrieben, wird Vollgas

nur auf geradlinigen Überflügen empfohlen. Umkehrflüge

sollten bei halber Gaszufuhr durchgeführt werden, um die

Wärmeabgabe der Elektronik zu verringern. Soll ein 6S

ununterbrochen betrieben werden, die optionalen Propeller

(PRB282006 oder PRB282027) verwenden.

1. Setzen Sie die beiden Akkupacks links und rechts

seitlich am Bootsrumpf ein. Sichern Sie die Akkus

mit den mitgelieferten Haken- und Schlaufengurten.

Wenn Sie das Boot in rauen Gewässern verwenden,

sollten Sie wasserdichtes Haken- und Schlaufenband

(DYNK0300) verwenden, um die Akkus noch sicherer

am Akkufach zu fixieren.

Tipp: Bringen Sie die Akkus zunächst so weit vorne

wie möglich an und versetzen Sie sie dann schrittweise

um je ca. 60 mm zum Bug hin, bis Ihr Boot die

Höchstgeschwindigkeit erreicht.

2. Schließen Sie beide Akkus an die Regleranschlüsse an.

Der mitgelieferte Propeller bietet die beste Leistung

zwischen 4S (14,8 V) und 5S LiPo (18,5 V). Die

5S-Konfiguration kann erreicht werden, indem ein 3S LiPo

(DYNB3811EC) auf der linken Seite des Bootes und ein

2S LiPo (DYNB3810EC) auf der rechten Seite des Boots

befestigt wird. Das zusätzliche Gewicht des 3S-Akkus auf

der linken Seite wird der durch den Propeller auf hoher

Drehzahl verursachten Drehung entgegenwirken.

WARNUNG: Bei der Verwendung von 2 Akkus in

Serie immer sicherstellen, dass sie ungefähr die

gleichen Bedingungen (Alter) aufweisen und über

dieselbe Kapazität (mA) und Entladungsrate (C-Rate)

verfügen. Ein Nichtbeachten kann zu Schäden an

den Akkus führen und möglicherweise einen Brand

verursachen.

INCH READY

RUN BRUSHLESS BOAT

La pagina sta caricando ...

ProBoat UL-19 30" Hydroplane Brushless RTR Manuale utente

Marca: ProBoat

Modello: UL-19 30" Hydroplane Brushless RTR

Categoria: Giocattoli telecomandati

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: ProBoat UL-19 30" Hydroplane Brushless RTR User manual
français: ProBoat UL-19 30" Hydroplane Brushless RTR Manuel utilisateur
Deutsch: ProBoat UL-19 30" Hydroplane Brushless RTR Benutzerhandbuch

ProBoat UL-19 30" Hydroplane Brushless RTR Manuale utente

ProBoat UL-19 30" Hydroplane Brushless RTR Manuale utente

in altre lingue

Documenti correlati

Altri documenti