IBM 621410U - IntelliStation E - Pro 6214 Hardware Maintenance Manual

Ha rdw ar e M ain tenan ce Man u al

IBM IntelliStation E Pro Type 6204 and

Ty pe 6214

򔻐򗗠򙳰

Ha rdw ar e M ain tenan ce Man u al

IBM IntelliStation E Pro Type 6204 and

Ty pe 6214

򔻐򗗠򙳰

Note

Before using this information and the product it supports, be sure to read the general information under “Notices” on

page 165.

Second Edition (June 2002

The following paragraph does not apply to the United Kingdom or any country where such provisions are

inconsistent with local law.

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION ″AS IS″ WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do

not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not

apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the

information herein; these changes will be incorporated in new editions of the publication. IBM may make

improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time.

This publication was developed for products and services offered in the United States of America. IBM may not

offer the products, services, or features discussed in this document in other countries, and the information is subject

to change without notice. Consult your local IBM representative for information on the products, services, and

features available in your area.

Requests for technical information about IBM products should be made to your IBM reseller or IBM marketing

representative.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

About this manual

This manual contains diagnostic information, a Symptom-to-FRU index, service

information, error indications, and configuration information for the IBM

IntelliStation E Pro Type 6204 and Type 6214 computer.

Important: This manual is intended for trained servicers who are familiar with

IBM PC computer products. Before servicing an IBM product, be sure

to review “Safety information” on page 131.

Important safety information

Be sure to read all caution and danger statements in this book before performing

any of the instructions.

Leia todas as instruções de cuidado e perigo antes de executar qualquer operação.

Prenez connaissance de toutes les consignes de type Attention et

Danger avant de procéder aux opérations décrites par les instructions.

Lesen Sie alle Sicherheitshinweise, bevor Sie eine Anweisung ausführen.

Accertarsi di leggere tutti gli avvisi di attenzione e di pericolo prima di effettuare

qualsiasi operazione.

Lea atentamente todas las declaraciones de precaución y peligro ante de llevar a

cabo cualquier operación.

Online support

Use the World Wide Web (WWW) to download diagnostic, BIOS flash, and device

driver files, and documents.

The Web address is:

http://www.ibm.com/pc/support

iv Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

Contents

About this manual ..........iii

Important safety information ........iii

Online support .............iv

General checkout ..........1

General information .........3

Features and specifications for the desktop model . . 4

Desktopmodel ............4

Towermodel.............5

Workstationfeatures............6

Reliability, availability, and serviceability features . . 6

Controls and indicators ...........8

Computeroperation............9

Turningonthecomputer.........9

Turningoffthecomputer.........10

Diagnostics.............11

Power-on Self Test (POST) .........11

Small computer system interface messages (some

models)................12

Diagnostic programs and error messages ....12

Textmessages ............13

Starting the diagnostic programs ......13

Using the Device Driver and IBM Enhanced

Diagnostics CD ...........14

Creating an IBM Enhanced Diagnostics

diskette..............14

Using the Enhanced diagnostics diskette....15

Viewing the test log ..........15

Diagnostic error messages .........15

Other diagnostic programs .........15

Software error messages ..........16

System programs ............16

Troubleshooting the Ethernet controller .....16

Network connection problems .......16

Ethernet controller troubleshooting chart . . . 17

Ethernet controller messages........18

Novell NetWare or IntraNetWare computer

ODIdriverteamingmessages......18

NDIS (Windows 2000 and XP) Event Viewer

messages.............20

Ethernetteamingmessages.......22

Intel Boot Agent messages .........24

Recovering your operating system and preinstalled

software...............25

Recovering or installing device drivers ....25

Recovering the operating system ......26

Performing a partial or full recovery ....26

Using the Recovery Repair diskette .....26

Using ConfigSafe and the Save Our System (SOS)

feature...............27

Erasing a lost or forgotten password (clearing

CMOS)................28

Recovering from a POST/BIOS update failure . . . 29

Replacing the battery ...........29

Configuration ............31

Using the IBM Setup Utility program......31

Starting the IBM Setup Utility program ....31

IBM Setup Utility main menu choices ....32

Main ..............32

Devices..............33

Startup..............33

Advanced .............34

Security .............34

Power..............35

Exit...............36

Using the SCSISelect Utility program (some models) 36

Starting the SCSISelect Utility program ....36

SCSISelect menu choices .........37

Using the Intel Boot Agent Utility program....37

Starting the Intel Boot Agent Utility program . . 38

Intel Boot Agent Utility menu choices ....38

Installing options ..........41

Before you begin ............41

System reliability considerations ......42

Desktopmodel.............42

Major components of the desktop model . . . 42

System board.............43

System board internal cable connectors . . . 44

System board external connectors .....44

CMOSrecoveryjumper........45

Installing options in a desktop model.....45

Removingthecover.........45

Removing the frame support bracket ....46

Working with adapters ........46

Internaldrives...........50

Memory module installation.......55

Security U-bolt installation .......56

Replacingthecover..........56

Towermodel..............57

System and PCI extender boards ......58

System board internal cable connectors . . . 59

System board external cable connectors . . . 60

CMOSrecoveryjumper........61

Installing options in a tower model .....61

Moving the stabilizing feet .......61

Side cover removal ..........63

Support bracket removal ........64

Working with adapters ........65

Internaldriveinstallation........69

Memory module installation.......74

Security U-bolt installation .......75

Replacingthecover..........77

Connecting external options .........77

Input/output connector locations ......78

Desktopmodel...........78

Towermodel............78

Input/output connectors .........78

Video connector ...........79

Keyboard connector .........80

Mouse connector ..........80

Parallel connector ..........81

Serial connectors...........82

Ethernet connector ..........82

Universal Serial Bus connectors......82

Audio connectors ..........83

Ultra160 SCSI connector ........83

FRU information (service only) ....87

Desktopmodel.............87

Adapter retainer............87

Airbaffle..............87

Fan................88

Power/LED switch ...........88

Power supply ............89

Processor / fan sink ..........89

Speaker...............90

System board.............91

Towermodel..............92

Adapter fan .............92

Adapter guide ............93

Adapter retainer............93

Bezel...............94

Bezel release latch ...........94

Fan................95

Handle cap .............96

Harddrivecage............97

PCI extender board...........97

Power/LED switch ...........98

Power supply ............99

Processor / fan sink ..........100

Speaker..............101

System board ............102

Top/sidecover............104

Symptom-to-FRU index .......105

Beepsymptoms ............105

Nobeepsymptoms...........108

Diagnostic error codes ..........109

Errorsymptoms............112

POST error codes ............114

ServeRAID..............119

Undetermined problems ..........119

Parts listing Intellistation E Pro . . . 121

System, Type 6204 ............121

Recovery CDs, Type 6204 ........124

System, Type 6214 ............125

Recovery CDs, Type 6214 ........127

Keyboards ..............128

Related service information .....131

Safety information............131

General safety ............131

Electrical safety............132

Safety inspection guide .........133

Handling electrostatic discharge-sensitive

devices ..............134

Grounding requirements ........135

Safety notices (multi-lingual translations) . . . 135

Send us your comments! .........164

Problem determination tips.........165

Notices ...............165

Trademarks..............166

vi Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

General checkout

The system diagnostic programs are stored on the Device Drivers and IBM Enhanced

Diagnostics CD. These programs are the primary method of testing the major

components of the workstation: The system board, Ethernet controller, video

controller, RAM, keyboard, mouse (pointing device), diskette drive, serial ports,

hard drives, and parallel port. You can also use them to test some external devices.

See “Diagnostics” on page 11.

Also, if you cannot determine whether a problem is caused by the hardware or by

the software, you can run the diagnostic programs to confirm that the hardware is

working properly.

When you run the diagnostic programs, a single problem might cause several error

messages. When this occurs, work to correct the cause of the first error message.

After the cause of the first error message is corrected, the other error messages

might not occur the next time you run the test.

A failed system might be part of a shared DASD cluster (two or more systems

sharing the same external storage device(s)). Prior to running diagnostics, verify

that the failing system is not part of a shared DASD cluster.

A system might be part of a cluster if:

v The customer identifies the system as part of a cluster.

v One or more external storage units are attached to the system and at least one of

the attached storage units is additionally attached to another system or

unidentifiable source.

v One or more systems are located near the failing system.

If the failing system is suspected to be part of a shared DASD cluster, all

diagnostic tests can be run except diagnostic tests which test the storage unit

(DASD residing in the storage unit) or the storage adapter attached to the storage

unit.

Notes:

1. For systems that are part of a shared DASD cluster, run one test at a time in

looped mode. Do not run all tests in looped mode, as this could enable the

DASD diagnostic tests.

2. If multiple error codes are displayed, diagnose the first error code displayed.

3. If the computer hangs with a POST error, go to “Symptom-to-FRU index” on

page 105.

4. If the computer hangs and no error is displayed, go to “Undetermined

problems” on page 119.

5. Power supply problems, see “Symptom-to-FRU index” on page 105.

6. Safety information, see “Safety information” on page 131.

7. For intermittent problems, check the error log; see “POST error codes” on

page 114.

001 IS THE SYSTEM PART OF A CLUSTER?

YES. Schedule maintenance with the customer. Shut down all

systems related to the cluster. Run storage test.

NO. Go to step 002.

002 IF THE SYSTEM IS NOT PART OF A CLUSTER:

v Power-off the computer and all external devices.

v Check all cables and power cords.

v Set all display controls to the middle position.

v Power-on all external devices.

v Power-on the computer.

v Record any POST error messages displayed on the screen. If an

error is displayed, look up the first error in the “POST error

codes” on page 114.

v Check the System Error Log. If an error was recorded by the

system, see “Symptom-to-FRU index” on page 105.

v Start the Diagnostic Programs. See “Starting the diagnostic

programs” on page 13.

v Check for the following responses:

1. One beep.

2. Readable instructions or the Main Menu.

003 DID YOU RECEIVE BOTH OF THE CORRECT RESPONSES?

NO. Find the failure symptom in “Symptom-to-FRU index” on

page 105.

YES. Run the Diagnostic Programs. If necessary, refer to

“Diagnostic programs and error messages” on page 12.

If you receive an error, go to “Symptom-to-FRU index” on

page 105.

If the diagnostics completed successfully and you still suspect a

problem, see “Undetermined problems” on page 119.

2 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

General information

The IBM IntelliStation E Pro computer incorporates many of the latest advances in

computing technology and can be expanded and upgraded as needs change. If you

have access to the Internet, you can obtain up-to-date information about the

computer and other IBM computer products at

http://www.ibm.com/pc/intellistation on the World Wide Web.

Refer to the following illustrations for the location of the computer model and

serial number labels. You will need these numbers to register your computer with

IBM.

Note: The illustrations in this document might differ slightly from your hardware.

Serial number

Desktop model:

Serial number

Tower model:

Features and specifications for the desktop model

This section describes features and specifications.

Desktop model

The following table provides a summary of the features and specifications of the

desktop model. Some features and specifications are not available on all models.

Microprocessor:

Depending on model:

v Intel

®

Pentium

®

4 with 256 KB

Level-2 cache

v Intel Pentium 4 with 512 KB

Level-2 cache

Memory:

ECC or NP, depending on model:

v Minimum: 128 MB

v Maximum: 1.0 GB

v Type: PC133 DIMMs

v Slots: two dual inline

Internal drives:

v Hard disk drive: IDE or SCSI

v One of the following:

– CD-ROM: IDE

– DVD-ROM: IDE

– CD-RW: IDE

Power supply:

160 watt (90-240 V ac)

Expansion bays:

v Two 5.25-in. bays (one CD-ROM

drive installed, one hard disk

drive installed)

v One 3.5-in. bay (one diskette

drive installed)

PCI expansion slots:

Three 33 MHz/32-bit

low-profile slots on the system

board

Video adapter:

Depending on model:

v NVIDIA Quadro2 EX LP AGP

adapter with 32 MB video memory

v NVIDIA Quadro4 LP adapter with 64

MB video memory

v Matrox G450 DVI LP adapter with 32

MB video memory

Integrated functions:

v 10BASE-T/100BASE-TX Ethernet

controller on the system board with

RJ-45 Ethernet port

v Two serial ports

v One parallel port

v Two USB ports

v Keyboard port

v Mouse port

v Audio ports

– Line out

– Line in

– Mic

v Dual-channel bus mastering IDE

controller

Size and weight:

v Height: 104 mm (4.1 in.)

v Depth: 412 mm (16.2 in.)

v Width: 360 mm (14.2 in.)

v Weight: approximately 10.9 kg (24 lb)

when fully configured or 6.8 kg (15.0

lb) minimum

Acoustical noise emissions:

v Sound power, idling: 5.1 bel

maximum

v Sound power, operating: 5.2 bel

maximum

Environment:

v Air temperature:

– Computer on: 10° to 35° C (50.0°

to 95.0° F). Altitude: 0 to 2133 m

(6998.0 ft)

– Computer off: 10° to 43° C (50.0°

to 109.4° F). Maximum altitude:

2133 m (6998.0 ft)

v Humidity:

– Computer on: 8% to 80%

– Computer off: 8% to 80%

Heat output:

Approximate heat output in British

thermal units (Btu) per hour

v Minimum configuration: 257 Btu (75

watts)

v Maximum configuration: 686 Btu

(200 watts)

Electrical input:

v Sine-wave input (50-60 Hz) required

v Input voltage low range:

– Minimum: 90 V ac

– Maximum: 137 V ac

v Input voltage high range:

– Minimum: 180 V ac

– Maximum: 265 V ac

v Input kilovolt-amperes (kVA)

approximately:

– Minimum: 0.08 kVA

– Maximum: 0.52 kVA

4 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

Tower model

The following table provides a summary of the features and specifications of the

tower model. Some features and specifications are not available on all models.

Microprocessor:

One of the following:

v Intel

®

Pentium

®

4 with 256 KB

Level-2 cache

v Intel Pentium 4 with 512 KB

Level-2 cache

Memory:

ECC or NP, depending on model:

v Minimum: 128 MB

v Maximum: 1.5 GB

v Type: PC133 DIMMs

v Slots: three dual inline

Internal drives:

v Hard disk drive: IDE or SCSI

v One of the following:

– CD-ROM: IDE

– DVD-ROM: IDE

– CD-RW: IDE

Power supply:

340 watt (90-240 V ac)

Expansion bays:

v Two 5.25-in. bays (1 CD-ROM

drive installed)

v Five 3.5-in. bays (1 diskette drive

installed)

PCI expansion slots:

v Three 33 MHz/32-bit slots on

the system board

v Two 33 MHz/32-bit slots on the

adapter extender card

Video adapter:

Depending on model:

v Matrox G450 AGP adapter with 16

MB SDRAM video memory

v Matrox G450 DVI adapter with 32

MB video memory

v NVIDIA Quadro2 Pro AGP adapter

with 64 MB DDR SDRAM video

memory

v NVIDIA Quadro4 adapter with 64

MB video memory

v Fire GL 8800 video adapter with 128

MB video memory

Integrated functions:

v 10BASE-T/100BASE-TX Ethernet

controller on the system board with

RJ-45 Ethernet port

v Two serial ports

v One parallel port

v Two USB ports

v Keyboard port

v Mouse port

v Audio ports

– Line out

– Line in

– Mic

v Dual-channel bus mastering IDE

controller

Size and weight:

v Height: 445 mm (17.5 in.)

v Depth: 498 mm (19.6 in.)

v Width: 165 mm (6.5 in.)

v Weight: approximately 19.5 kg (43 lb)

when fully configured or 15.9 kg (35

lb) minimum

Acoustical noise emissions:

v Sound power, idling: 5.1 bel

maximum

v Sound power, operating: 5.2 bel

maximum

Environment:

v Air temperature:

– Computer on: 10° to 35° C (50.0°

to 95.0° F). Altitude: 0 to 2133 m

(6998.0.7 ft)

– Computer off: 10° to 43° C (50.0°

to 109.4° F). Maximum altitude:

2133 m (6998.0 ft)

v Humidity:

– Computer on: 8% to 80%

– Computer off: 8% to 80%

Heat output:

Approximate heat output in British

thermal units (Btu) per hour

v Minimum configuration: 257 Btu (75

watts)

v Maximum configuration: 1455 Btu

(425 watts)

Electrical input:

v Sine-wave input (50-60 Hz) required

v Input voltage low range:

– Minimum: 90 V ac

– Maximum: 137 V ac

v Input voltage high range:

– Minimum: 180 V ac

– Maximum: 265 V ac

v Input kilovolt-amperes (kVA)

approximately:

– Minimum: 0.08 kVA

– Maximum: 0.52 kVA

General information 5

Workstation features

The IntelliStation E Pro takes advantage of advancements in data storage, memory,

systems management, and network environments. The computer includes:

v High performance accelerated graphics port (AGP) graphics

The computer comes with an AGP graphics adapter installed. This

high-performance adapter supports high resolutions and includes many

performance-enhancing features for the operating-system environment.

v Large system memory

The memory bus in the computer supports up to 1.5 GB of system memory. The

memory controller provides error code correction (ECC) support for up to three

industry-standard PC133, 3.3V, 168-pin, 133 Megahertz (MHz), unregistered,

synchronous dynamic random access memory (SDRAM) dual inline memory

modules (DIMMs).

v Systems-management capabilities

The computer comes with features that a network administrator or file server

can can use to remotely manage and control the computer. Some of the features

include: Wake on LAN

®

, Remote Administration, and System Migration

Assistant.

v Integrated network environment support

The computer comes with an Ethernet controller on the system board. This

Ethernet controller has an interface for connecting to 10-Mbps or 100-Mbps

networks. The computer automatically selects between 10BASE-T and

100BASE-TX environments. The controller provides full-duplex (FDX) capability,

which enables simultaneous transmission and reception of data on the Ethernet

local area network (LAN).

Reliability, availability, and serviceability features

Three important computer design features are reliability, availability, and

serviceability (RAS). The RAS features help to ensure the integrity of the data that

is stored on the computer, the availability of the computer when you need it, and

the ease with which you can diagnose and repair problems.

The following is an abbreviated list of the RAS features that the computer

supports. Many of these features are explained in later chapters of this publication.

v Reliability features

– Boot block recovery

– Cooling fans with speed-sensing capability

– Error code correction (ECC) front-side buses (FSBs)

– ECC L2 cache and system memory

– Parity checking on the small computer system interface (SCSI) and peripheral

component interconnect (PCI) buses

– Advanced configuration and power interface (ACPI)

– Power-on self-test (POST)

– Synchronous dynamic random access memory (SDRAM) with serial presence

detect (SPD)

v Availability features

– Advanced Desktop Management Interface (DMI) features

– Auto-restart initial program load (IPL) power supply

– Automatic error retry or recovery

– Automatic computer restart after power failure

– Built-in, menu-driven configuration and setup programs

6 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

– Built-in, menu-driven SCSI configuration programs (some models)

– Monitoring support for temperatures, voltages, and fan speed

– Upgradable basic input/output system (BIOS), diagnostics and POST

– Wake on LAN (WOL) capability

v Serviceability features

– 3-year warranty

– Adaptec built-in self-test (BIST)

– Preinstalled Ethernet adapter

– CD-ROM-based diagnostics programs

– Diagnostic support of Ethernet adapters

– Error codes and messages

– Processor serial number access

– Read-only memory (ROM) checksums

– Vital product data (VPD); includes serial number information and

replacement part numbers, stored in nonvolatile memory, for easier remote

maintenance

General information 7

Controls and indicators

The controls and indicators of the tower and desktop models are identified below.

Hard disk drive

activity light

Power-on light

Power-control

button

CD eject

button

CD-ROM drive

activity light

Diskette drive

activity light

Diskette

eject button

Ethernet transmit/

receive activity

Ethernet speed

100 Mbs

Note: The front bezel door is not shown here so that the drive bays may be

illustrated.

CD eject

button

CD-ROM drive

activity light

Diskette eject

button

Hard disk drive

activity light

Power-on

light

Power control

button

Diskette drive

activity light

Ethernet speed 100 Mbps

Ethernet transmit

receive activity

8 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

CD-ROM drive eject button: opens and closes the CD tray.

CD-ROM drive activity light: indicates when the CD-ROM drive is in use.

Diskette drive activity light: indicates when the diskette drive is in use.

Diskette drive eject button: releases a diskette from the drive.

Ethernet speed 100 Mbps: when this light is on, the Ethernet speed is 100 Mbps.

When this light is off, the Ethernet speed is 10 Mbps.

Ethernet transmit/receive activity: when this light is on, there is activity between

the computer and the network.

Power-control button: enables you to turn the computer on or off manually.

Power-on light: indicates when the computer is turned on.

Hard disk drive activity light: indicates when the hard disk drive is in use.

Computer operation

The following sections provide information about operating the workstation.

Turning on the computer

Do the following to start the computer:

1. Turn on all peripheral devices first.

2. Press the power-control button on your computer. For the location of the

power- control button, see “Controls and indicators” on page 8.

What you see and hear when you start up your computer depends on the features

installed and the settings in the IBM Setup Utility program.

If power-on self-test (POST) detects a problem, there might be a series of beeps or

no beep, and a numeric error message might appear on the screen. Write down

any beep series and error code numbers with descriptions, then see “Beep

symptoms” on page 105 for the explanation of error codes.

During startup, the following messages might be displayed briefly:

v To start the Product Recovery Program, Press F11

v Hit <F2> if you want to run SETUP

v Press CTRL+A for SCSISelect Utility (some models only)

To use these features, press the appropriate function key or keys quickly. The

messages appear for only seconds. For more information about these messages, see

“Using the IBM Setup Utility program” on page 31 and “Using the SCSISelect

Utility program (some models)” on page 36.

During startup, you might not see Hit <F2> if you want to run SETUP.Ifyou

want to see the prompt, see instructions for displaying the prompt in “Using the

IBM Setup Utility program” on page 31.

The IBM Setup Utility program will help you configure your computer with

passwords, PCI adapter configuration, and other options. The IBM Setup Utility

General information 9

menu is displayed at the top of the screen. To navigate the menu and screen items,

follow the directions on the right of the screen.

The operating system and application programs initiate from the hard disk drive.

If your computer is attached to a network, the computer will begin attaching to

any LANs and remote applications to which you have access. A network

administrator can also ″wake up″ your computer (start it remotely) to download

programs or gather information about computer performance.

Turning off the computer

Turn off the computer as follows:

Statement 5:

CAUTION:

The power-control button on the device and the power switch on the power

supply do not turn off the electrical current supplied to the device. The device

also might have more than one power cord. To remove all electrical current from

the device, ensure that all power cords are disconnected from the power source.

1

2

v Press the power control button on the front of the computer. This starts orderly

shutdown of the operating system, if this feature is supported by your operating

system, and places the computer in standby mode.

Note: After turn off the computer, wait at least 5 seconds before you press the

power control button to turn on the computer again.

v Press and hold the power control button for more than 4 seconds to cause an

immediate shutdown of the computer and place the computer in standby mode.

You can use this feature if the operating system stops functioning.

v If you cannot use the power control button to turn off your computer,

disconnect the computer power cords from the electrical outlets.

Note: After disconnecting the power cords, wait approximately 15 seconds for

your computer to stop running.

Important: In some circumstances, the computer might not turn off immediately

when you press the power control button. If this happens, press and

hold the power control button until the computer turns off.

10 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

Diagnostics

Power-on Self Test (POST) .........11

Small computer system interface messages (some

models)................12

Diagnostic programs and error messages ....12

Textmessages ............13

Starting the diagnostic programs ......13

Using the Device Driver and IBM Enhanced

Diagnostics CD ...........14

Creating an IBM Enhanced Diagnostics

diskette..............14

Using the Enhanced diagnostics diskette....15

Viewing the test log ..........15

Diagnostic error messages .........15

Other diagnostic programs .........15

Software error messages ..........16

System programs ............16

Troubleshooting the Ethernet controller .....16

Network connection problems .......16

Ethernet controller troubleshooting chart . . . 17

Ethernet controller messages........18

Novell NetWare or IntraNetWare computer

ODI driver teaming messages ......18

NDIS (Windows 2000 and XP) Event Viewer

messages.............20

Ethernetteamingmessages.......22

Intel Boot Agent messages .........24

Recovering your operating system and preinstalled

software...............25

Recovering or installing device drivers ....25

Recovering the operating system ......26

Performing a partial or full recovery ....26

UsingtheRecoveryRepairdiskette.....26

Using ConfigSafe and the Save Our System (SOS)

feature...............27

Erasing a lost or forgotten password (clearing

CMOS)................28

Recovering from a POST/BIOS update failure . . . 29

Replacing the battery ...........29

Power-on Self Test (POST)

When you turn on the computer, it performs a series of tests to check the operation

of system components and some of the options that are installed in the computer.

This series of tests is called the power-on self-test or POST.

If POST finishes without detecting any problems, the first window of the operating

system or application program appears.

Notes:

1. If you have a user password set, you must type the password and press Enter,

when prompted, before the operating system will load.

2. A single problem might cause several error messages. When this occurs, work

to correct the cause of the first error message. After you correct the cause of the

first error message, the other error messages usually will not occur the next

time you run the test.

The possible types of beep codes are as follows:

Repeating long beeps

Indicates that a memory error has occurred. Ensure that all DIMMs are

correctly installed.

One long beep and two short beeps

Indicates that a video error has occurred and the BIOS cannot initialize the

video screen to display any additional information. Ensure that the video

adapter is correctly installed.

For information about specific beep codes, see “Beep symptoms” on page 105.

Small computer system interface messages (some models)

If the computer has an Ultra160 SCSI adapter installed and you receive a SCSI

error message when running the SCSISelect Utility program, refer to the following

table for actions to take if you receive an error message.

Note: If your system does not have a SCSI hard disk drive, ignore any message

that indicates that the BIOS is not installed.

Table 1. SCSI messages

SCSI

Messages

Description

All One or more of the following might be causing the problem.

v A failing SCSI device (adapter or drive)

v An improper SCSI configuration

v Duplicate SCSI IDs in the same SCSI chain

v An improperly installed SCSI terminator

v A defective SCSI terminator

v An improperly installed cable

v A defective cable

Action: Verify that:

v The external SCSI devices are turned on. External SCSI devices

must be turned on before the computer.

v The cables for all external SCSI devices are connected correctly.

v The last device in each SCSI chain is terminated properly.

v The SCSI devices are configured correctly.

If the above items are correct, run the diagnostic programs to obtain

additional information about the failing device.

Diagnostic programs and error messages

The system diagnostic programs are stored on the Device Drivers and IBM Enhanced

Diagnostics CD. These programs are the primary method of testing the major

components of the computer.

Diagnostic error messages indicate that a problem exists; they are not intended to

be used to identify a failing part. Troubleshooting and servicing of complex

problems that are indicated by error messages should be performed by trained

service personnel.

Sometimes the first error to occur causes additional errors. In this case, the

computer displays more than one error message. Always follow the suggested

action instructions for the first error message that appears.

The following sections contain the error codes that might appear in the detailed

test log and summary log, when running the diagnostic programs.

The error code format is as follows:

fff-ttt-iii-date-cc-text message

12 Hardware Maintenance Manual: IBM IntelliStation E Pro Type 6204 and Type 6214

La pagina si sta caricando...

IBM 621410U - IntelliStation E - Pro 6214 Hardware Maintenance Manual

Questo manuale è adatto anche per

IBM 621410U - IntelliStation E - Pro 6214 Hardware Maintenance Manual

in altre lingue

Documenti correlati

Altri documenti