LG LXN0356QC Manuale del proprietario

TELECOM AIR CONDITIONERS

INSTALLATION INSTRUCTIONS

l Please read this instruction sheet completely before installing the product.

l When the power cord is to be replaced, replacement work shall be performed by authorized

personnel only.

l Installation work must be performed in accordance with national wiring standards by authorized

personnel only.

ENGLISH

3.0TR SINGLE PHASE: LX-0356QC

3.5TR SINGLE PHASE: LX-0456QC

INDEX

3

1.The following should be always observed for safety ...................

2. Product Specification ..........................................................................

2.1 Product Description .............................................................................

2.2 Inspection ............................................................................................

2.3 Technical specification .......................................................................

3. Installation Standard ..........................................................................

3.1 Pre-check ...........................................................................................

3.2 Levelling of Airconditioner ..................................................................

3.3 Shelter Cut - out sealing ......................................................................

3.4.Condensate Drain Pipe .......................................................................

3.5 Air purging of connecting pipes & Indoor unit ......................................

3.6 Filter Cleaning .....................................................................................

3.7 Installation Drawing - Cases 1& 2 ...............................................

3.8 Installation Drawing - Foundation ......................................................

4. Controller ............................................................................................

4.1 Display & Indicators ...........................................................................

4.2 Pre-Startup instructions ....................................................................

4.3 Operations ...................................................................................

4.4 LCD menu details ........................................................................

5.Trouble Shooting ...............................................................................

5.1 Symptoms & Problems .....................................................................

6.Electrical wiring diagram ..................................................................

6.1 Indoor wiring Diagram .......................................................................

6.2 Outdoor wiring Diagram ....................................................................

6.3 Controller Connection Diagram .........................................................

7.Exploded view .....................................................................................

7.1 indoor unit ..........................................................................................

7.2 Outdoor unit .......................................................................................

7.3 Part List ........................................................................................

4~5

6

7

8

9

10

11~14

15

16

17

18~19

20~27

28

29

30

31

32

33~34

ENGLISH

1. The following should be always observed for safety

The supplied unit requires 3 phase supply to operate, so please make sure to have authorised

Be sure to read "THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY" before

installing the air conditioner.

Be sure to observe the cautions specified here as they include important items related to safety.

The indications and meanings are as follows.

After reading this manual, be sure to keep it together with the owner's manual in an accessible place.

Could lead to death, serious injury, etc.

Could lead to serious injury in particular environments when operated incorrectly.

WARNING

CAUTION

connection by the supply authority before connecting to the system.

Do not install it yourself (customer).

Perform the installation securely referring to the

installation manual.

Install the unit securely in a place which can bear the

weight of the unit.

Attach the electrical part cover to the indoor unit and

the service panel to the outdoor unit securely.

Be sure to use the part provided or specified parts for

the installation work.

Check that the refrigerant gas do not leak after

installation is completed.

Use the specified wires to connect the indoor and the

outdoor units securely and attach the wires firmly to

the terminal board connecting sections so the stress

of the wires is not applied to the sections.

Incomplete installation could cause injury due to fire, electric shock,

the unit falling or a leakage of water Consult the dealer from whom

you purchased the unit or authorised installer.

Incomplete installation could cause a personal injury due to

fire, electric shock, the unit falling or a leakage of water.

When installed in an insufficient strong place, the unit could f all

causing injured.

Incomplete connecting and fixing could cause fire.

The use of defective parts could cause an injury or leakage of

water due to a fire, electric shock, the unit falling, etc.

If the electrical part cover if the indoor unit and/or the service

panel if the outdoor unit are not attached securely, it could result

in a fire or electric shock due to dust, water, etc.

WARNING

Perform electrical work according to the installation

manual and be sure to use an exclusive circuit.

If the capacity of the power circuit is insufficient or there is

incomplete electrical work, it could result in a fire or an electric

shock.

4

Be cautious when unpacking and installing

the product.

Be sure the installation area does not deteriorate

with age.

If the base collapses, the air conditioner could fall with it,

causing property damage, product failure and personal injury.

Sharp edges could cause injury. Be especially careful of the

case edges and the fins on condenser and evaporator.

Always install a dedicated circuit and breaker.

Do not modify or extend the power cable.

There is risk of fire or electric shock. Improper wiring or installation may cause fire or electric shock.

Always ground the product.

Use the correctly rated circuit breaker.

There is risk of fire or electric shock. There is risk of fire or electric shock.

Do not use a defective or under rated circuit breaker.

Use this appliance on a dedicated circuit.

There is risk of fire or electric shock.

Perform the drainage/piping work securely

according to the installation manual.

If there is a defect in the drainage/piping work, water

could drop from the unit and household goods could be

wet and damaged.

Do not install the unit in a place where an

inflammable gas leaks.

If gas leaks and accumulates in the area surrounding the unit, it

could cause an explosion.

CAUTION

Always check for refrigerant R-22 leakage after

installing or repair of product.

Low refrigera nt R-22 levels may cause malfun ctionin g

of product.

Use two or more people to lift and transport the

product.

Avoid personal injury.

Do not install the product where the noise or hot air

coming from the outdoor unit could harm your

neighbors.

It may cause problem to your neighbors.

Keep the level of your airconditioner as mentioned

in manual to avoid vibration or water leakage.

Do not install the product where it will be exposed to

sea wind (Salt spray) directly.

It may cause corrosion on product. Corrosion,

particularly on the condenser and evaporator fins,

could cause product malfunction or inefficie nt operation.

5

ENGLISH

6

2. PRODUCT SPECIFICATION

2.1 PRODUCT DESCRIPTION:

Airconditioner is composed of evaporator unit and condensing unit. Evaporator

unit is positioned on top of condensing unit and connected with interconnection

pipes. Condenser section consists of compressor, propeller fan, fan motor and

condenser coil. And Evaporator section consists of evaporator coil, centrifugal

blower, blower motor and logical controller. Airconditioner is equipped with dual

independent Airconditioning cycle for reliability measures.

2.2 INSPECTION:

1. Check the damage after unit is unloaded, report promptly to the carrier, any

damage found to unit. Do not drop the unit.

2. Open the Packing carefully to check the unit in upright position.

3. Check the unit dents, paint damage, tube pinch offs, tube parts touching with

sheet metals, mechanical components and electrical wires connections.

4. Condensing unit is precharged with R-22 gas from factory. Ensure gas in

condensing unit before installation.

7

UNITS LX-0356QC

TR 3.0

BTU/HR 18600 X 2

KCAL/HR 4650 X 2

KCAL/HR 4185 X 2

KCAL/HR 465 X 2

NOS 2

Rotary

NOS 2

Hitachi

SH315CV-C7HU

Sq.M 0.223

NOS 2

FPI/No 14/2

Cu/Al-Precoat

Sq.M 0.272

NOS 2

FPI/No 14/3

Cu/Al-Precoat

INDUCTION MOTOR

NOS 2

230V-1PH-50Hz

RPM 960

mm 17

B CLASS

INDUCTION MOTOR

NOS 2

230V-1PH-50Hz

mm 12.7

B CLASS

RPM 880

CENTRIFUGAL,FORWARD

CURVE, DIDW

NOS 2

PROPELLER -AXIAL

Plastic

NOS 2

mm 19

mm 12.7x2

mm 9.52x2

mm 665

mm 762

mm 938

KGS 90

KGS 85

mm 665

mm 550

mm 1080

KGS 110

KGS 105

DESCRIPTION

COMPRESSOR TYPE

QTY

MAKE

MODEL

EVAPORATOR FACE AREA

QTY

FIN DENSITY/ROWS

MATERIAL OF TUBE/FIN

CONDENSER FACE AREA

QTY

FIN DENSITY/ROWS

MATERIAL OF TUBE/FIN

INDOOR MOTOR TYPE

QUANTITY

POWER SUPPLY

SPEED

SHAFT DIAMETER

CLASS OF INSULATION

OUTDOOR MOTOR TYPE

QUANTITY

POWER SUPPLY

SHAFT DIAMETER

CLASS OF INSULATION

FAN SPEED

BLOWER

TYPE

QTY

FAN TYPE

FAN MATERIAL

QTY

CONNECTIONS CONDENSATE DRAIN SIZE

GAS OUTLET SIZE OD (nos)

LIQUID INLET SIZE,OD (nos)

OVERALL DIMENSION-INDOOR (A)WIDTH

(B)DEPTH

©HEIGHT

WEIGHT-INDOOR WEIGHT GROSS

WEIGHT NET

OVERALL DIMENSION-OUTDOOR WIDTH

DEPTH

HEIGHT

WEIGHT-OUTDOOR WEIGHT GROSS

WEIGHT NET

SENSIBLE COOLING CAPACITY

LATENT COOLING CAPACITY

NO OF REFRIGERANT CIRCUITS

NOMINAL COOLING CAPACITY

TOTAL COOLING CAPACITY

2.3 TECHNICAL SPECIFICATIONS

ENGLISH

LX-0456QC

3.5

21000 X 2

5250 X 2

4725 X 2

525 X 2

CFM 825 X 2AIRFLOW

960 X 2

2

Rotary

2

Hitachi

SH315CV-C7HU

0.223

2

14/3

Cu/Al-Precoat

0.272

2

14/3

Cu/Al-Precoat

INDUCTION MOTOR

2

230V-1PH-50Hz

1100

17

B CLASS

INDUCTION MOTOR

2

230V-1PH-50Hz

12.7

B CLASS

880

CENTRIFUGAL,FORWARD

CURVE, DIDW

2

PROPELLER -AXIAL

Plastic

2

19

12.7x2

9.52x2

665

762

938

92

87

665

550

1080

110

105

8

3.1 PRE-CHECK:

1. Remove the packing wooden base from indoor & outdoor unit.

2. Place the outdoor unit over mounting base (Concrete or I –beam) and

place antivibration pad and mount as per installation instructions.

FLARED TYPE INTERCONNECTING PIPING SIZE X QTY.

SUCTION LINE INTERCONNECTING PIPING 1/2 inch X 2

LIQUID LINE INTER CONNECTING PIPING 3/8 inch X 2

7. Align the centre of the pipings (2 suctions & 2 liquids) and sufficiently tighten the

flare nut with fingers.

8. Finally tighten the flare nut with torque wrench until the wrench clicks (40~80kgf).

When tightening the flare nut with torque wrench, ensure the direction of

tightening follows the arrow of wrench.

6. Wrap Teflon tape in direction of thread to the connectors & service valve before

placing flared tubing.

3. INSTALLATION STANDARD

3. Positioned the Indoor unit over Top of condensing unit and bolted indoor

with outdoor after fixing indoor to shelter cut-out portion.

4. Check there should not be any dents, dust in interconnecting piping.

5. Prepare inter connection pipe to connect indoor unit with outdoor unit as

per following.

Liquid

Interconnection

Suction

Interconnection

(A)

9

3.2. Levelling of Airconditioner

After placing the unit on Channel/concrete structure

maintain the levelling of unit towards rear side with

10mm slope so as to ensure free flow drainage.

Water seepage problem may happen due to improper

levelling of unit.

3.4. Condensate Drain pipe

3.3. Shelter Cutout sealing

Angle flanges (4 nos) to be fixed with shelter wall after

installation. These flanges are to be fixed with shelter

wall after installation so as to prevent any leakage in

shelter. after fixing the flanges; apply silicon sealant

on edges of flanges to make complete leak free

cut-out. These are not the part of unit accessories.

1. Air conditioner is provided with one flexible drain

pipe, which shall be connected to metal Drain pipe

of unit & should be routed through gap between

shelter wall and condensing unit (see fig. C).

2. Do Not leave drain pipe open, your airconditioner

may suck condensate water and cause splitting of

water inside the shelter.

(B)

(C)

ENGLISH

10

The air which contains moisture remaining in the refrigeration cycle may cause

malfunction of compressor.

1. Confirm the both liquid valves& gas valves are set to closed position.

2. After connecting the piping, check the joints for gas leakage with gas leal

detector.

3. Remove the service port nut, and connect the gauge manifold and vacuum

pump to the service port by charge hose.

4. Vacuum the indoor unit & connecting pipes until the pressure in them lowers

to below 76 cmHg.

5. Remove the valve stem nuts. and fully open the stems of service valves with

hexagon wrench. & Tight the flare nuts of indoor & outdoor unit.

6. Purge the gas qty-80grams in each circuit to remove moist air contents.

7. Disconnect the charge hose and fit the nut to the service port.

(Tightening torque:1.8kg.m)

3.5. Air purging of inter connection & Indoor unit

The Airconditioner is equipped with fine air filter (2 nos.). The Air filter are at

front of unit shall be checked and cleaned every month or more often

if necessary.

3.6. Filter Cleaning

Air-filter

11

AC UNIT

SHELTER WALL

CONCRETE

BASE

3.7. INSTALLATION DRAWING - CASE 1 :

CONCRETE BASEMOUNTING

ENGLISH

NOTE:

Concrete top should be in level of shelter base. All measurement have

been taken from concrete top (levels with shelter base) in mm.

SHELTER CUT-OUT SIZE: 675mm (WIDTH) X 955mm (HEIGHT)

12

SHELTER "WIDTH"

675

955

2065

SHELTER

"HEIGHT"

1110

950

13

INSTALLATION DRAWING - CASE 2 :

CHANNEL BASE MOUNTING

AC UNIT

SHELTER WALL

I-CHANNEL\

MOUNTING

ENGLISH

14

NOTE:

Shelter should based on I beam and unit base should be mounted on

cross beam as shown in diagram.

SHELTER CUT-OUT SIZE: 675mm (WIDTH) X955mm (HEIGHT)

675

955

2065 + "Y"

1110 + "Y"

SHELTER

"HEIGHT"

SHELTER "WIDTH"

15

3.8. INSTALLATION DRAWING : FOUNDATION

950

680

X

CONCRET BASE

NOTE : REAR VIEW OF

L FLANGE FITTED

TO SHELTER WALL.

NOTE : IN CASE OF USING FOUNDATION BOLT (OPTIONAL) CUTOUT HEIGHT

SHALL BE INCREASED AS PER HEIGHT OF FOUNDATION BOLT.

ANTI VIBRATION PAD (AV PAD-4 NOS)

NOTE : ALWAYS PLACE AV PAD (4 NOS) AT

BOTTOM OF BASE MOUNTING CHANNEL

ENGLISH

SHELTER WALL

160

355

360

160

120

475

MOUNTING HOLE DIA 10X4 (TYP.)

675

955

HP / LP

RH %

AMB

Lock Parameter

7

8

9

10

LEGENDS

7 Segment display

COMP

DAMP

FC / EFC

MCB

CT

1

2

3

4

5

6

4.1. DISPLAY & INDICATORS

16

4. CONTROLLER

1

3

5

6

7

4

2

8

9

10

2

1

°c

COMP

BLOW

DAMP

AMB RH%

FC / EFC MCB CT HP / LP

COMP DAMP FC / EFC MCB CT HP / LP

BLOW

UNIT

1

UNIT

2

RH AMB

CT1 CT2

SET

RESET

LED indications and status

LED LED Status Description

FC ON

OFF

Flashing

ON

OFF

ON/OFF

DAMPER

BLOWER

Flashing

ON/OFF

Flashing

COMP

MCB

CT

HP/LP

ON

Flashing

ON

Flashing

ON

AMB PROBE

RH

PROBE

ON(Red)

Flashing

Free Cooling in Progress

Free/Emergency Cooling is not in Progress

Emergency Cooling is in Progress

Damper Actuator in motion

Damper Actuator Stopped

BLOWER is ON//OFF

BLOWER in time delay

COMPRESSOR is ON/OFF

COMPRESSOR in time delay

Represents the respective units

MCB FAULT

CT FAULT (UL/OL/CP)

HP FAULT

LP FAULT

Ambient Temperature Probe Fail

RH Probe fail (RH>99%)

RH Probe fail (RH<10%)

Flashing (in prog.

and set mode)

17

KEY PAD

4.2. CONTROLLER: Pre-Start up Instructions

Check the transit damage to controller before carrying out power supply

connection to controller in AC.

Connect the proper Power Supply to air conditioner as per specification.

Place the ambient and humidity sensor in correct position. Room Sensor to

be fix on specified location to sense correct room temperature.

If Power Key is Pressed for 4 Secs the Unit will toggle between ON / OFF

Status.

If Power Supply of Units is not connected properly, then controller will give

MCB error.

Check For Proper connection from Supply to the controller input terminal.

ENGLISH

If MCB error still exists then Reverse Phase and Neutral Of the Supply.

Key Functions

Key Description

Key to view compressor1 current and up key.

Key to view compressor2 current and down key.

Key to view Ambient Temperature.

Key to view Shelter Humidity (%RH).

To save parameters and to enter set mode.

To reset any pending faults in the controller.

To switch ON or switch OFF UNIT1.

To switch ON or switch OFF UNIT2.

SET

CT2

CT1

RESET

AMB

RH

UNIT1

UNIT2

18

S.N.

Parameters

Description

Range Factory set

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

4.3 Operations

P1

P2

P3

P4

P5

P6

t2

t3

t4

Ad

C0

C1

C2

C3

C4 & C5

L1

L3

L4

L5

L6

D0

D1

D2

D3

LP

E1

PA

FS

EP

Unit Selection - 1 & 2

Max. Allowable High Temp. Limit

Min. Allowable Low Temp. Limit

Diff. Setting of Set Pt. 1 & 2

Probe Calibration

Restart Time Delay bet. Comp. 1 & 2

Start 2nd Comp in case 1st Comp. cannot achieve the lower Set point

Set Min. Off time between the two Comp.

Avoid Overloading of either Comp.

Set Power on time delay for High Temp. Alarm

Set Low Current Limit for Comp. 1

Set low Current Limit for Comp. 2

Set High Current Limit for Comp.1

Set High Current Limit for Comp. 2

Set Time Delay for Current Alarms

Free Cooling Enable/Disable for Unit 1

Free Cooling Set point

Set Differential for Damper

Set Humidity Limit to allow Free Cooling

Set Differential for Humidity

Enable/Disable HP Fault for Unit 1

Enable/Disable HP Faut for Unit 2

Enable/Disable LP Fault for Unit 1

Enable/Disable LP Fault for Unit 2

Keypad Lock

Relay Status on Probe Failure

Password Change

Default Restore Settings

End Programming

0 è 2

XX è 50°C

0° è XX °C

1° è 20°C

-10° è +10°C

0 è 20 Min

0 è 30 Min

0 è 15 Secs

0 è 12 Hrs

0 è 20 Min

1 è C2 A

1 è C3 A

C0 è 20 A

C1 è 20 A

0 è 30 Min

0 è 1

10° è XX °C

1° è 4°C

10% è 99%

3% è 10%

0 è 1

1 è 1

2 è 1

3 è 1

0 è 1

0 è 2

0 è 99

0 è 1

0

42°C

14°C

2°C

0°C

3 Min

0

5 Sec

12 Hrs

20 Min

1A

10A

1 Min

0

16°C

2°C

70%

5%

1

0

48

0

Exit Programming Mode

19

Thermostatic operation

Note:

If both the compressors are OFF due to Thermostatic operation, duty blower will continue

to run.

The compressor & condenser fan will switch OFF simultaneously.

Duty blower ON 55 ± 5 sec

Duty Condenser fan ON Programable

Duty compressor ON Programable

Standby blower ON 55 ± 5 sec

Standby Condenser fan ON Programable

Standby compressor ON Programable

Switch ON sequencing:

Duty compressor & condenser fan cut-OFF Set-1°C

Duty compressor & condenser fan cut-IN Set + Differential °C

Set + Differential °C

Standby compressor & condenser fan cut-OFF Set °C

Standby compressor & condenser fan cut-IN

ENGLISH

20

4.4. LCD Operation Menu

3. P1 parameter

Function : Unit selection

parameter of Controller .

To change

P1 parameter,

Press set key

.

when display

shows P1

Use UP/DOWN key to set

desired range.

When P1 is set to

0 Both Cooling units are selected.

1 Cooling Unit 1 is selected.

2 Cooling Unit 2 is selected

Setting this parameter

at 1 will select Unit1 only,unit2

will be off. Setting this parameter

to 0 will allow to function both the

units simeoutanously

Example :

Min. Max. Fac.

0 2

0

3

4. P2 parameter

Function : To set maximum

allowable high temperature limit.

To change

P2 parameter,

Press set key

.

when display

shows P2

Use UP/DOWN key to set

desired range. Once set at a

particular range, this will not

allow both set points to go above

this range and below P3 setting.

Setting this parameter

at 35 C will not allow both set

points to go above 35 C. Also if

the temperature reaches 35 C, the

display will show Ht (High

Temperature), indicating that the

temperature has reached or gone

above the range in this

parameter.

Example :

0

Min. Max. Fac.

XX C

0

50 C

0

42 C

0

Ht

4

XX C--Largest

set point

0

1

1. Set Point Function : To set the cutout point

of the controller.

Press & hold

set key for 4

seconds and

release.

Set point 1

Set Point 2

Display will show 0 and flash. Press

Up/Down keys to enter password.

User can go into set mode by

entering correct password.

Comp1LED will flash along with

respective setpoint1 for compressor

1. The setpoint1 range can now be

changed by using the UP/DOWN

keys. After achieving the desired

range, press the set key and

you will see !----" which confirms

that the set point has been stored

in memory.

Comp2 LED will flash along with

respective setpoint 2 for

compressor 2. In the similar

manner use UP/DOWN key to

set the desired range and press

set key to confirm the settings.

Min. Max. Fac.

0 C

0

20 C

0

50 C

0

SET

Min. Max. Fac.

0 C

0

50 C

0

24 C

0

SET

2

2. Parameter

Setting

Hold up &

down keys

simultaneously

for 4 seconds.

Display will show 0 & flash. To enter

programming mode enter correct

password by using Up/Down keys

and press set key.

Once user enters correct password

display will show P2 and flash.

To go to other parameters, use

up / down keys.

If user enters incorrect password,

controller will come out of

programming mode and will display

temperature.

Function : To set the other

parameters of the controller.

CT2

CT1

La pagina sta caricando ...

LG LXN0356QC Manuale del proprietario

Questo manuale è adatto anche per

LG LXN0356QC Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti