Hangar 9 HAN2820 Manuale del proprietario

Marca: Hangar 9

Modello: HAN2820

Categoria: Giocattoli telecomandati

Tipo: Manuale del proprietario

P-51D Mustang 20cc

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

 SPECIFICATIONS • SPEZIFIKATIONEN • SPÉCIFICATIONS • SPECIFICHE

69.5 in (1.76 m)

848.0 sq in (54.7 dm2) Total/Totale

60.0 in (1.52 m)

11.5–13 lbs (5200–5900 g)

2-Stroke Gas: 20cc, 4-Stroke gas/petrol: 20cc

2-Takt Benziner: 20cc, 4-Takt Benzin: 20 cc

2 temps Essence: 20cc, 4 temps essence: 20cc

2-Tempi Gas: cc, 4 tempi benzina: 20 cc

Electric Power: Power 60, 470Kv Brushless

Elektro Antrieb Power: Power 60, 470Kv Brushless

Moteur électrique (EP): Power 60, 470Kv Brushless

Motore elettrico: Power 60, 470Kv Brushless

7-channel (or greater) with 7 servos

7-Kanal (oder größer) mit 7-Servos

7 voies (ou plus) avec 7 servos

a 7 canali (o più) con 7 servo

Spinner: 3

inch(Included)

Spinner: 95mm(Enthalten)

Cône: 95mm (Fourni)

Ogiva dell’elica: 95mm (Inclusa)

6.25-inches (159mm)

P-51D Mustang 20cc

Part # English Deutsch Français Italiano

 REPLACEMENT PARTS • ERSATZTEILE • PIÈCES DE RECHANGE • PEZZI DI RICAMBIO

HAN282001 Fuselage with Hatch Rumpf mit Haube Fuselage avec capot Fusoliera con portello

HAN282002 Left-Hand Wing with Aileron and Flap Tragﬂ äche Links mit Querruder und Klappe Aile gauche avec aileron et volet Semiala sinistra con alettone e ﬂ ap

HAN282003 Right-Hand Wing with Aileron and Flap Tragﬂ äche Rechts mit Querruder und Klappe Aile droite avec aileron et volet Semiala destra con alettone e ﬂ ap

HAN282004 Stabilizer with Elevator Höhenruderset Set Plan horizontal et Gouverne de profondeur Set stabilizzatore ed elevatore

HAN282005 Rudder Seitenleitwerk Gouverne de direction Timone

HAN282006 Cowling and Exhaust Motorhaube und Auspuff Capot et échappement Cappottatura e scarico

HAN282007 Top Hatch Obere Abdeckung Trappe supérieure Portello superiore

HAN282008 Canopy Kabinenhaube Verrière Calotta

HAN282009 Painted Pilot Lackierter Pilot Pilote peint Pilota verniciato

HAN282010 Pushrod Set Gestänge / Anlenkungen Set Jeu de tringleries Set dell’asta di spinta

HAN282011 Hardware Set Kleinteile Set Sachet de visserie Set dei pezzi

L HAN282012 Main Wheels Fahrwerksräder Set Paire de roues principales Set ruota principale

HAN282013 Decal Set (3) Dekorbögen (3) Planche de décoration (3) Foglio con decalcomanie (3)

HAN282014 Tailwheel Spornrad Roue de queue Ruotino di coda

HAN282015 Spinner Spinner Cône Ogiva dell’elica

HAN282016 Main Landing Gear Struts Hauptfahrwerk-Streben Jambes du train d’atterrissage principal Gambe del carrello di atterraggio principale

HAN282017 Wing Tube Tragﬂ ächenverbinder Clé d’aile Tubo dell’ala

HAN282019 Engine Mount Set Motor-Montagesatz Jeu de renfort moteur Set di montaggio motore

HAN282020 Radio Antenna Funkantenne Antenne de la radio Antenna radio

HAN282021 Gear Door Set Fahrwerkklappen-Satz Jeu de trappes de train Set portello del carrello

HAN282022 Scale Detail Parts Scale Zubehör Paket Sachet d’accessoires maquette Pacchetto accessori in scala

 SMALL PARTS (NOT SHOWN) • KLEINTEILE (NICHT ABGEBILDET) • PETITES PIÈCES (NON REPRÉSENTÉES) • PARTI DI PICCOLE DIMENSIONI (NON MOSTRATE)

HAN282018 Fuel Tank Kraftstofftank Réservoir de carburant Serbatoio del carburante

 REQUIRED RADIO EQUIPMENT • ERFORDERLICHE RC AUSRÜSTUNG • ÉQUIPEMENT RADIO REQUIS • APPARECCHIATURE RADIO NECESSARIE

SPMA3000 x3 Heavy-Duty Servo Extension 3-inch Servokabelverlängerung 75 mm (3 inch) Rallonge de servo, 75 mm Estensione servo 3 pollici

EFLG510

60-120 85 degree Strut Ready Main Electric

Retract

60-120 85Grad Strebe einsatzbereit elektrische

Haupteinfahrvorrichtung

Système de rentrée électrique principal à 85

degrés60-120, prêt à être monté sur jambe

Elemento retrattile elettrico principale 60-120,

85 gradi, pronto da montare

SPMA3001 x2 Heavy-Duty Servo Extension 6-inch Servokabelverlängerung 150 mm (6 inch) Rallonge de servo, 150 mm Estensione servo 6 pollici

SPMA3002 x4 Heavy-Duty Servo Extension 9-inch Servokabelverlängerung 230 mm (9 inch) Rallonge de servo, 230 mm Estensione servo 9 pollici

SPMA3003 x2 Heavy-Duty Servo Extension 12-inch Servokabelverlängerung 300 mm (12 inch) Rallonge de servo, 300 mm Estensione servo 12 pollici

SPMAR9350 AR9350 9 Channel AS3X Receiver AR9350 AS3X-Empfänger mit 9Kanälen Récepteur AS3X 9 canaux AR9350 Ricevitore AS3X a 9 canali AR9350

Part # English Deutsch Français Italiano

 2-STROKE GAS • 2-TAKT BENZINER • 2 TEMPS ESSENCE • 2-TEMPI A BENZINA

APC16080 Competition Pattern Propeller,16 x 8 Competition Propeller, 16 x 8 Hélice 16 x 8 Competition Elica da competizione, 16 x 8

DUB799

Tygon

Gas Tubing,3' Medium

Tygon-Gasrohre, 1 m (3 Fuß) m Durchschnitt Tube à essence Tygon, 91,4 cm (3 pi) moyen Tubo per carburante Tygon, 3 piedi, medio

EVOA112 Evolution 3 Wire Ignition/RX Switch Evolution Zündschalter Interrupteur Evolution 3 ﬁ ls Allumage/RX

Evolution, interruttore a 3 ﬁ li accensione/

ricevitore

EVOE20GX2 20GX Gas Engine w/Pumped Carb 20GX 20cc (1.20 cu. in.) Benzinmotor Moteur essence 20GX 20cc Motore a benzina 20GX 20cc (1.20 cu. in.)

HAN116 Fuel Filler with “T” and Overﬂ ow Fitting Hangar 9 Tanknippel mit T Stück u. Überlauf Fitting Point de remplissage de carburant avec coupleur en T Bocchettone di riempimento carburante con

SPM9530 Spektrum™ 3-Wire Switch Harness Spektrum™ dreiadriges Schalterkabel Câblage d’interrupteur 3 ﬁ ls Spektrum™ Interruttore di accensione a 3 ﬁ li Spektrum™

SPMB2000LPRX 2000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 2000 mAh) Batterie Li-Po de récepteur 7,4 V 2000 mAh Batteria per ricevitore da 7,4 V Li-Po, 2.000 mAh

SPMB4000LPRX 4000mAh 2S 7.4V LiPo Receiver Battery LiPo-Empfängerakku (7,4 V / 4000 mAh) Batterie Li-Po de récepteur 7,4 V 4000 mAh Batteria per ricevitore da 7,4 V Li-Po, 4.000 mAh

SPMSA6380 x8 A6380 H-T/H-S Digital HV Servo A6380 H-T/H-S Digitaler HV-Servo ServoA6380 H-T/H-S numérique HV Servo HV digitale H-T / H-S A6380

 ELECTRIC POWER • ELEKTROANTRIEB • MOTEUR ELECTRIQUE (EP) • MOTORE ELETTRICO

EFLM1934 Prop Adapter: Power 46/52/60 Propelleradapter: Power 46/52/60 Adaptateur d’hélice : 46/52/60 Adattatore dell’elica: Power 46/52/60

APC16080E Electric Propeller, 16 x 8E Elektro Propeller, 16 x 8E Hélice électrique, 16 x 8E Elica elettrica sottile, 16 x 8E

CSE010009700 Talon 90-Amp 25V BL ESC W/20amp BEC

Talon 90 A 25 V bürstenloser Geschwindigkeitsregler

mit 20 A BEC

Variateur ESC Talon 90 A 25 V BL avec BEC 20 A ESC BL Talon 90-Amp 25 V con BEC 20amp

DYNC0021 EC5 Device Connector (2) EC5 Gerät-Steckverbinder (2) Connecteur du dispositifEC5 (2) Connettore dispositivo EC5 (2)

EFLAEC506 EC5 Extension Lead with 6-inch Wire, 10Awg EC5 Verlängerungsleitung mit 6-Zoll-Kabel, 10Awg Rallonge EC5 avec ﬁ l de 15 cm (6 po), 10 AWG

Cavo di prolunga EC5 con ﬁ lo da 15,24 cm, 10

AWG

EFLM4060B Power 60 BL Outrunner Motor, 470Kv Bürstenloser Außenläufer-Motor Leistung 60, 470Kv

Moteur à cage tournante sans balais Power 60 de

470Kv

Motore brushless a cassa rotante Power 60,

470Kv

KXSB0029 22.2V 7000mAh 6S 30C, 10AWG, EC5 7000 mA 6S 22,2 V 30C LiPo-Akku,10 AWG EC5

Batterie Li-Po 6S 22,2V 7000mA 30C, 10AWG prise

EC5

Batteria LiPo 30C 22,2V 6S 7000 mAh,10AWG

EC5

SPMA3001 Heavy-Duty Servo Extension 6-inch Servokabelverlängerung 150 mm (6 inch) Rallonge de servo, 150 mm Estensione servo 6 pollici

SPMSA6380 x7 A6380 H-T/H-S Digital HV Servo A6380 H-T/H-S Digitaler HV-Servo ServoA6380 H-T/H-S numérique HV Servo HV digitale H-T / H-S A6380

 REQUIRED ADHESIVES • ERFORDERLICHE KLEBSTOFFE • TYPES DE COLLES • ADESIVI NECESSARI

DLMAD44 Roket Rapid CA 5-10 sec: 20g Roket Rapid CA 5-10 s: 20g Colle cyano Roket Rapid 5-10 sec: 20g Colla cianoacrilica Roket Rapid 5-10 sec: 20 g

DLMAD45 Roket Max CA 10-20 sec: 20g Roket Max CA 10-20 s: 20g Colle cyano Roket Max 10-20 sec: 20g Colla cianoacrilica Roket Max 10-20 sec: 20 g

PAAPT715 CA Accelerator Sekundenkleber (CA) Aktivator Accélérateur de colle CA Accelerante colla CA

PAAPT37 5-Minute Epoxy 5 Minuten Epoxy Époxy 5 minutes Colla epossidica 5 minuti

PAAPT35 15-Minute Epoxy 15 Minuten Epoxy Époxy 15 minutes Colla epossidica 15 minuti

PAAPT42 Threadlock Schraubensicherungslack Frein-ﬁ let Frenaﬁ letti

DLMAD12 R/C Modeller Canopy Glue: 4 oz R/C Modeller Kanzelkleber: 113,4g (4 oz) Colle à verrière R/C Modeller: 113g Colla per capottine R/C Modeller: 4 oz

P-51D Mustang 20cc

Part # English Deutsch Français Italiano

 REQUIRED TOOLS • BENÖTIGTES WERKZEUG • OUTILS REQUIS • ATTREZZI NECESSARI

C-clamp Schraubzwinge Serre joint Morsetto a C

Drill Bohrer Mini-perceuse Trapano

Drill bit: 1/16-inch, 5/64-inch, 3/32-inch,

1/8-inch, 9/64-inch, 5/32-inch, 11/64-inch,

3/16-inch, 13/64-inch, 7/32-inch

Bohrer: 1,5mm, 2mm, 2,5mm, 3mm, 3,5mm, 4mm,

4,5mm, 5mm, 5,5mm, 6mm

Forêt : 1,5mm, 2mm, 2,5mm, 3mm, 3,5mm, 4mm,

4,5mm, 5mm, 5,5mm, 6mm

Punte per trapano: 1,5mm, 2mm, 2,5mm, 3mm,

3,5mm, 4mm, 4,5mm, 5mm, 5,5mm, 6mm

Felt-tipped pen Faserstift Feutre ﬁ n effaçable Pennarello

Epoxy brush Pinsel Pinceau Epoxy Spazzole epoxy

Flat ﬁ le Flachfeile Lime plate Lima piatta

Hemostats Klemme Pince Hemostat Pinzetta

Hex wrench: 1.5mm, 2mm, 2.5mm, 3mm Inbusschlüssel: 1,5mm, 2mm, 2,5mm, 3mm Tournevis hexagonal: 1,5mm, 2mm, 2,5mm, 3mm Chiave esag.: 1,5mm, 2mm, 2,5mm, 3mm

Hobby knife with #11 blade Hobbymesser mit # 11 Klinge Couteau : Lame numéro 11 Taglierino: #11 lama

Hook and loop tape Klettband Bande auto-agrippante Nastro a strappo

Hook and loop straps Klettgurt Bandes auto-agrippante Fascette a strappo

Isopropyl alcohol Isopropyl Alkohol Alcool isopropylique Alcol isopropilico

Low-tack tape Kreppband Adhésif de masquage Nastro a bassa aderenza

Needle nose pliers Spitzzange Pince ﬁ ne Pinze a becco stretto

Mixing cups and sticks Mischbecher und Rührstäbchen Récipients pour mélanger et bâtons Contenitori e stick per mixer colla

Nut driver: 7mm Steckschlüssel. 7mm Clés à douilles : 7mm Chiave per dadi: 7mm

Paper towels Papiertücher Papier absorbant Asciugamani di carta

Pencil Stift Crayon à papier Matita

Phillips screwdriver: #1, #2 Phillips Schraubendreher: #1, #2 Tournevis cruciforme: #1, #2 Cacciavite a croce: #1, #2

Pin vise Handbohrer Porte forets Trapano manuale

Pliers Zange Pince Pinze

Ruler Lineal Réglet Righello

Sandpaper Schleifpapier Papier de verre Carta vetrata

Scissors Schere Ciseaux Forbici

Side cutters Seitenschneider Pince coupante Lama laterale

Square Geodreieck Équerre Squadra

Tapered reamer Zulaufende Reibahle Alésoir conique Alesatore rastremato

Tie wraps Kabelbinder Colliers Fascette avvolgenti

T-pins T- Nadeln Epingles Spilli a T

Toothpicks Zahnstocher Cure dents Stuzzicadenti

Tubing bender Rohrbieger Cintreuse Curvatubi

Vise grips Klemmen Pince-étau Pinze bloccanti

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon

Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

The following terms are used throughout the product literature to indicate various levels of potential harm when

operating this product:

Meaning of Special Language

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage,

and serious injury OR create a high probability of superﬁ cial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a

possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or

no possibility of injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious

injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic

mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage

to the product or other property. This product is not intended for use by children without direct adult supervision. Do

not attempt disassembly, use with incompatible components or augment product in any way without the approval

of Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to

read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate

correctly and avoid damage or serious injury.

AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT A TOY.

 USING THE MANUAL

This manual is divided into sections to help make assembly easier to understand.

 SAFETY WARNINGS AND PRECAUTIONS

Read and follow all instructions and safety precautions before use. Improper use can result in ﬁ re, serious injury and

damage to property.

Components

Use only with compatible components. Should any compatibility questions exist, please refer to the product

instructions, component instructions or contact the appropriate Horizon Hobby ofﬁ ce.

Flight

Fly only in open areas to ensure safety. It is recommended ﬂ ying be done at radio control ﬂ ying ﬁ elds. Consult local

ordinances before choosing a ﬂ ying location.

Propeller

Keep loose items that can become entangled in the propeller away from the prop. This includes loose clothing or other

objects such as pencils and screwdrivers. Keep your hands away from the propeller as injury can occur.

Batteries

Always follow the manufacturer’s instructions when using and disposing of any batteries. Mishandling of Li-Po

batteries can result in ﬁ re causing serious injury and damage.

Small Parts

This kit includes small parts and should not be left unattended near children as choking and serious injury could result.

 SAFE OPERATING RECOMMENDATIONS

• Inspect your model before every ﬂ ight to ensure it is airworthy.

• Be aware of any other radio frequency user who may present an interference problem.

• Always be courteous and respectful of other users in your selected ﬂ ight area.

• Choose an area clear of obstacles and large enough to safely accomodate your ﬂ ying activity.

• Make sure this area is clear of friends and spectators prior to launching your aircraft.

• Be aware of other activities in the vicinity of your ﬂ ight path that could cause potential conﬂ ict.

• Carefully plan your ﬂ ight path prior to launch.

• Abide by any and all established AMA National Model Aircraft Safety Code.

 BEFORE STARTING ASSEMBLY

• Remove parts from bag.

• Inspect fuselage, wing panels, rudder and stabilizer for damage.

• If you ﬁ nd damaged or missing parts, contact your place of purchase.

• Charge transmitter and receiver batteries.

• Center trims and sticks on your transmitter.

• For a computer radio, create a model memory for this particular model.

• Bind your transmitter and receiver, using your radio system’s instructions.

IMPORTANT: Rebind the radio system once all control throws are set. This will keep the servos from moving to

their endpoints until the transmitter and receiver connect. It will also guarantee the servo reversal settings are

saved in the radio system.

 FAA INFORMATION

If you own this product, you may be required to register with the FAA.

For up-to-date information on how to register with the FAA, please visit https://registermyuas.faa.gov/.

For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyouﬂ y.org/.

 BUILDING PRECAUTIONS

During assembly, we recommend resting the parts on a soft surface such as a soft towel to help prevent denting the

sheeting.

P-51D Mustang 20cc

Propeller

Halten Sie lose Gegenstände die sich im Propeller verfangen können weg vom Propeller. Dieses gilt auch für Kleidung

oder andere Objekte wie zum Beispiel Stifte oder Schraubendreher.

Halten Sie ihre Hände weg vom Propeller, es besteht akute Verletzungsgefahr.

Akkus

Folgen Sie immer den Herstelleranweisungen bei dem Gebrauch oder Entsorgung von Akkus. Falsche Behandlung von

LiPo Akkus kann zu Feuer mit Körperverletzungen und Sachbeschädigung führen.

Kleinteile

Dieser Baukasten beinhaltet Kleinteile und darf nicht unbeobachtet in der Nähe von Kindern gelassen werden, da die

Teile verschluckt werden könnten mit ernsthaften Verletzung zur Folge.

 EMPFEHLUNGEN ZUM SICHEREN BETRIEB

• Überprüfen Sie zur Flugtauglichkeit ihr Modell vor jedem Flug.

• Beachten Sie andere Piloten deren Sendefrequenzen ihre Frequenz stören könnte.

• Begegnen Sie anderen Piloten in ihrem Fluggebiet immer höﬂ ich und respektvoll.

• Wählen Sie ein Fluggebiet, dass frei von Hindernissen und groß genug ist.

• Stellen Sie vor dem Start sicher, dass die Fläche frei von Freunden und Zuschauern ist.

• Beobachten Sie den Luftraum und andere Flugzeuge/Objekte die ihren Flugweg kreuzen und zu einem Konﬂ ikt

führen könnten.

• Planen Sie sorgfältig ihren Flugweg vor dem Start.

 VOR DEM ZUSAMMENBAU

• Entnehmen Sie zur Überprüfung jedes Teil der Verpackung.

• Überprüfen Sie den Rumpf, Tragﬂ ächen, Seiten- und Höhenruder auf Beschädigung.

• Sollten Sie beschädigte oder fehlende Teile feststellen, kontaktieren Sie bitte den Verkäufer.

• Laden des Senders und Empfängers.

• Zentrieren der Trimmungen und Sticks auf dem Sender.

• Sollten Sie einen Computersender verwenden, resetten Sie einen Speicherplatz und benennen ihn nach dem Modell.

• Sender und Empfänger jetzt nach den Bindeanweisung des Herstellers zu binden.

WICHTIG: Wir empfehlen dringend nachdem alle Einstellungen vorgenommen worden sind, das Modell neu zu binden.

Dieses verhindert, dass die Servos in die Endanschläge laufen bevor sich Sender und Empfänger verbunden haben. Es

garantiert auch, dass die Servoreverseeinstellungen in der RC Anlage gesichert sind.

 HINWEISE ZUM BAU

Während des Zusammenbaus empfehlen wird, dass die Teile auf einer weichen Oberﬂ äche, wie einem Handtuch,

abgelegt werden, um ein Eindrücken der Bleche zu verhindern.

HINWEIS

Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby,

LLC. jederzeit geändert werden Die aktuelle Produktliteratur ﬁ nden Sie auf horizonhobby.com unter der Registerkarte

„Support“ für das betreffende Produkt.

Spezielle Bedeutungen

Die folgenden Begriffe werden in der gesamten Produktliteratur verwendet, um auf unterschiedlich hohe

Gefahrenrisiken beim Betrieb dieses Produkts hinzuweisen:

WARNUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden,

Kollateralschäden und schwere Verletzungen ODER mit hoher Wahrscheinlichkeit oberﬂ ächliche Verletzungen.

ACHTUNG: Wenn diese Verfahren nicht korrekt befolgt werden, ergeben sich wahrscheinlich Sachschäden UND die

Gefahr von schweren Verletzungen.

HINWEIS: Wenn diese Verfahren nicht korrekt befolgt werden, können sich möglicherweise Sachschäden UND geringe

oder keine Gefahr von Verletzungen ergeben.

WARNUNG: Lesen Sie die GESAMTE Bedienungsanleitung, um sich vor dem Betrieb mit den Produktfunktionen

vertraut zu machen. Wird das Produkt nicht korrekt betrieben, kann dies zu Schäden am Produkt oder persönlichem

Eigentum führen oder schwere Verletzungen verursachen.

Dies ist ein hochentwickeltes Hobby-Produkt. Es muss mit Vorsicht und gesundem Menschenverstand betrieben

werden und benötigt gewisse mechanische Grundfähigkeiten. Wird dieses Produkt nicht auf eine sichere und

verantwortungsvolle Weise betrieben, kann dies zu Verletzungen oder Schäden am Produkt oder anderen Sachwerten

führen. Dieses Produkt eignet sich nicht für die Verwendung durch Kinder ohne direkte Überwachung eines

Erwachsenen. Verwenden Sie das Produkt nicht mit inkompatiblen Komponenten oder verändern es in jedweder Art

ausserhalb der von Horizon Hobby, LLC vorgegebenen Anweisungen. Diese Bedienungsanleitung enthält Anweisungen

für Sicherheit, Betrieb und Wartung. Es ist unbedingt notwendig, vor Zusammenbau, Einrichtung oder Verwendung

alle Anweisungen und Warnhinweise im Handbuch zu lesen und zu befolgen, damit es bestimmungsgemäß betrieben

werden kann und Schäden oder schwere Verletzungen vermieden werden.

NICHT GEEIGNET FÜR KINDER UNTER 14 JAHREN. DIES IST KEIN SPIELZEUG.

 ÜBER DIESE ANLEITUNG

Diese Anleitung ist zur Vereinfachung des Zusammenbaues in Sektionen unterteilt.

 WARNUNGEN UND SICHERHEITS-VORKEHRUNGEN

Bitte lesen und befolgen Sie alle Anweisungen und Sicherheitsvorkehrungen vor dem Gebrauch. Falscher, nicht

sachgemäßer Gebrauch kann Feuer, ernsthafte Verletzungen und Sachbeschädigungen zur Folge haben.

Komponenten

Verwenden Sie mit dem Produkt nur kompatible Komponenten. Sollten Fragen zur Kompatibilität auftreten, lesen Sie

bitte die Produkt- oder Bedienungsanweisung oder kontaktieren den Service von Horizon Hobby.

Fliegen

Fliegen Sie um Sicherheit garantieren zu können, nur in weiten offenen Gegenden. Wir empfehlen hier den Betrieb auf

zugelassenen Modellﬂ ugplätzen. Bitte beachten Sie lokale Vorschriften und Gesetze, bevor Sie einen Platz zum Fliegen

wählen.

L’hélice

Gardez éloignés tous les éléments qui pourraient être attrapés par l’hélice. Cela inclut les vêtements larges ou les

objets comme des outils par exemple. Gardez toujours vos mains à distance pour éviter tout cas de blessures.

Les batteries

Suivez toujours les instructions du fabricant de vos batteries. Une mauvaise manipulation d’une batterie Li-Po peut

entraîner un incendie causant de graves dégâts matériels et des blessures corporelles.

Petites pièces

Ce kit contient des petites pièces qui ne doivent pas être laissées à la portée des enfants, ces pièces sont dangereuses

pour eux et peuvent entraîner de graves blessures.

 CONSIGNES DE SÉCURITÉ CONCERNANT L’UTILISATION

• Inspectez votre modèle avant chaque vol.

• Surveillez les fréquences utilisées à proximité.

• Soyez toujours courtois et respectueux des autres utilisateurs de la zone de vol.

• Choisissez une zone dégagée de tout obstacle et sufﬁ samment grande pour voler en toute sécurité.

• Contrôlez que la zone est libre de spectateurs avant de lancer votre modèle.

• Soyez conscient des autres activités aux alentours de votre vol, risque de conﬂ it potentiel.

• Planiﬁ ez votre vol avant de le commencer.

 AVANT DE COMMENCER L’ASSEMBLAGE

• Retirez toutes les pièces des sachets pour les inspecter.

• Inspectez soigneusement le fuselage, les ailes et les empennages.

• Si un élément est endommagé, contactez votre revendeur.

• ll est recommandé de préparer tous les éléments du système de la radio.

• Cela inclut la charge des batteries comme la mise au neutre des trims et des manches de votre émetteur.

• Si vous utilisez une radio programmable, sélectionnez une mémoire libre aﬁ n d’y enregistrer les paramètres de ce

modèle.

• Nous vous recommandons d’affecter maintenant le récepteur à l’émetteur en suivant les instructions fournies avec

votre radio.

IMPORTANT: Il est hautement recommandé de ré-affecter le système une fois que les courses seront réglées. Cela

empêchera les servos d’aller en butée lors de la connexion du système. Cela garantit également que la direction des

servos est enregistrée dans l’émetteur.

 PRÉCAUTIONS D’ASSEMBLAGE

Lors de l’assemblage de votre modèle, nous vous recommandons de poser les pièces sur une surface douce comme

une serviette douce pour éviter d’abîmer l’entoilage.

REMARQUE

La totalité des instructions, garanties et autres documents est sujette à modiﬁ cation à la seule discrétion d’Horizon

Hobby, LLC. Pour obtenir la documentation àjour, rendez-vous sur le site horizonhobby.com et cliquez sur l’onglet de

support de ce produit.

Signiﬁ cation de certains termes spéciﬁ ques

Les termes suivants sont utilisés dans l’ensemble du manuel pour indiquer différents niveaux de danger lors de

l’utilisation de ce produit:

AVERTISSEMENT: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels

et des blessures graves OU engendrer une probabilité élevée de blessure superﬁ cielle.

ATTENTION: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET des

blessures graves.

REMARQUE: Procédures qui, si elles ne sont pas suivies correctement, peuvent entraîner des dégâts matériels ET

éventuellement un faible risque de blessures.

AVERTISSEMENT: Lisez la TOTALITÉ du manuel d’utilisation aﬁ n de vous familiariser avec les caractéristiques du

produit avant de le faire fonctionner. Une utilisation incorrecte du produit peut entraîner sa détérioration, ainsi que des

risques de dégâts matériels, voire de blessures graves.

Ceci est un produit de loisirs sophistiqué. Il doit être manipulé avec prudence et bon sens et requiert des aptitudes

de base en mécanique. Toute utilisation irresponsable de ce produit ne respectant pas les principes de sécurité peut

provoquer des blessures, entraîner des dégâts matériels et endommager le produit. Ce produit n’est pas destiné à

être utilisé par des enfants sans la surveillance directe d’un adulte. N’essayez pas de modiﬁ er ou d’utiliser ce produit

avec des composants incompatibles hors des instructions fournies par Horizon Hobby, LLC. Ce manuel comporte des

instructions relatives à la sécurité, au fonctionnement et à l’entretien. Il est capital de lire et de respecter la totalité

des instructions et avertissements du manuel avant l’assemblage, le réglage et l’utilisation, ceci aﬁ n de manipuler

correctement l’appareil et d’éviter tout dégât matériel ou toute blessure grave.

14 ANS ET PLUS. CECI N’EST PAS UN JOUET.

 UTILISATION DU MANUEL

Ce manuel est divisé en sections pour vous aider à comprendre plus facilement l’assemblage.

 AVERTISSEMENTS RELATIFS À LA SÉCURITÉ

Lisez et suivez toutes les instructions relatives à la sécurité avant utilisation. Une utilisation inappropriée peut entraîner

un incendie, de graves blessures et des dégâts matériels.

Composants

Utilisez uniquement des composants compatibles. Si vous avez des questions concernant la compatibilité, référez-vous

à ce manuel ou contactez le service technique Horizon Hobby.

Le vol

Volez uniquement dans des zones dégagées pour un maximum de sécurité. Il est recommandé d’utiliser les pistes des

clubs d’aéromodélisme. Consultez votre mairie pour connaître les sites autorisés.

P-51D Mustang 20cc

AVVISO

Tutte le istruzioni, le garanzie e gli altri documenti pertinenti sono soggetti a cambiamenti a totale discrezione di

Horizon Hobby, LLC. Per una documentazione aggiornata sul prodotto, visitare il sito www.horizonhobby.com e fare

clic sulla sezione Support per questo prodotto.

Signiﬁ cato dei termini particolari

In tutta la documentazione relativa al prodotto sono utilizzati iseguenti termini per indicare vari livelli di potenziale

pericolo durante il funzionamento:

AVVERTENZA: Procedure che, se non debitamente seguite, espongono alla possibilità di danni alla proprietà ﬁ sica

opossono omportare un’elevata possibilità di provocare ferite superﬁ ciali. Ulteriori precauzioni per la sicurezza e

avvertenze.

ATTENZIONE: Procedure che, se non sono seguite correttamente, possono creare danni materiali E possibili gravi

lesioni.

AVVISO: Procedure che, se non sono seguite correttamente, possono creare danni materiali E nessuna oscarsa

possibilità di lesioni.

AVVERTENZA: Leggere TUTTO il manuale di istruzioni e prendere familiarità con le caratteristiche del prodotto, prima

di farlo funzionare. Un utilizzo scorretto del prodotto può causare danni al prodotto stesso, alle persone oalle cose,

provocando gravi lesioni.

Questo è un prodotto di hobbistica soﬁ sticato e NON un giocattolo. È necessario farlo funzionare con cautela e

responsabilità e avere conoscenze basilari di meccanica. Se questo prodotto non è utilizzato in maniera sicura e

responsabile potrebbero veriﬁ carsi lesioni odanni al prodotto stesso oad altre proprietà. Non è un prodotto adatto

aessere utilizzato dai bambini senza la diretta supervisione di un adulto. Non usare componenti non compatibili

o alterare il prodotto in nessuna maniera al di fuori delle istruzioni fornite da Horizon Hobby, LLC. Questo manuale

contiene le istruzioni per un funzionamento e una manutenzione sicuri. È fondamentale leggere e seguire tutte le

istruzioni e le avvertenze del manuale prima di montare, conﬁ gurare ofar funzionare il Prodotto, al ﬁ ne di utilizzarlo

correttamente e di evitare danni olesioni gravi.

MINIMO 14 ANNI. NON È UN GIOCATTOLO.

 COME USARE IL MANUALE

Questo manuale è diviso in sezioni per rendere più facile la comprensione del montaggio.

 AVVERTIMENTI E PRECAUZIONI PER LA SICUREZZA

Prima dell’uso leggere attentamente tutte le istruzioni e le precauzioni per la sicurezza. In caso contrario si potrebbero

procurare incendi, danni o ferite.

Componenti

Usare solo componenti compatibili. Se ci fossero dubbi riguardo alla compatibilità, è opportuno far riferimento alle

istruzioni relative al prodotto o ai componenti oppure rivolgersi al reparto Horizon Hobby di competenza.

Volo

Per sicurezza volare solo in aree molto ampie. Meglio se in campi volo autorizzati per modellismo. Consultare le

ordinanze locali prima di scegliere luogo dove volare.

Elica

Tenere gli oggetti liberi (vestiti, penne, cacciaviti, ecc.) lontano dall’elica, prima che vi restino impigliati. Bisogna fare

attenzione anche con le mani perché c’è il rischio di ferirsi anche gravemente.

Batterie

Quando si maneggiano o si utilizzano le batterie, bisogna attenersi alle istruzioni del costruttore; il rischio è di procurare

incendi, specialmente con le batterie LiPo, con danni e ferite serie.

Piccole parti

Questo kit comprende delle parti di piccole dimensioni e non lo si può lasciare incustodito se c’è la presenza di bambini

che li possono inghiottire e rimanere soffocati o intossicati.

 RACCOMANDAZIONI PER OPERARE IN SICUREZZA

• Controllare attentamente il modello prima di ogni volo per accertarsi che sia idoneo.

• Essere consapevoli che un altro utente della frequenza in uso, potrebbe procurare delle interferenze.

• Essere sempre cortesi e rispettosi nei confronti degli altri utilizzatori dell’area in cui ci si trova.

• Scegliere un’area libera da ostacoli e abbastanza ampia da permettere lo svolgimento del volo in sicurezza.

• Prima del volo veriﬁ care che l’area sia libera da amici e spettatori.

• Stare attenti alle altre attività che si svolgono in vicinanza della vostra traiettoria di volo, per evitare possibili conﬂ itti.

• Pianiﬁ care attentamente il volo prima di lanciare il modello.

• Rispettare sempre scrupolosamente le regole stabilite dall’associazione locale.

 PRIMA DI INIZIARE IL MONTAGGIO

• Togliere tutti i pezzi dalla scatola.

• Veriﬁ care che la fusoliera, l’ala e i piani di coda non siano danneggiati.

• Se si trovano parti danneggiate, contattare il negozio da cui è stato acquistato.

• Caricare il trasmettitore e la batteria di volo.

• Centrare stick e trim sul trasmettitore.

• Con una radio computerizzata creare una nuova memoria per questo modello.

• Facendo riferimento alle istruzioni del radiocomando, connettere (bind) trasmettitore e ricevitore.

IMPORTANTE: Ripetere la procedura di connessione una volta regolate le corse, per evitare che i servi vadano a ﬁ ne

corsa. Garantirà anche che le impostazioni di inversione del servo vengano salvate nel sistema radio.

 PRECAUZIONI PER LA COSTRUZIONE

Durante l’assemblaggio noi consigliamo di appoggiare le varie parti su di una superﬁ cie morbida come un

asciugamano di spugna per evitare ammaccature al rivestimento.

 TRANSPORTATION AND STORAGE

Use the 3-view drawing at the back of this manual to

determine the amount of space required to transport and

store your model. The model can be disassembled, so the

amount of room necessary can vary. We recommend the

use of a wing bag to help protect these surfaces during

transport and storage. The control horns and linkages can

also cause damage to nearby surfaces even when placed

in storage bags. Always place surfaces so the tops are

together to prevent damage from the control horns and

linkages.

 PRINTED COVERING NOTES

• The covering used on your model has the coloring and

markings printed directly on the covering.

• The covering has a self-adhesive backing, and it is

not recommended to use heat as it may damage the

covering.

• Use only mild cleaning agents on the printed ﬁ nish.

Denatured alcohol is the most aggressive agent we

recommend, but test on an inconspicuous area ﬁ rst.

Prolonged use will remove the paint.

• Use tape with care. Anything other than low-tack tape

can remove the ﬁ nish, particularly on edges.

• Avoid contact with raw fuel, especially alcohol-based

fuels containing nitro methane.

• Remove exhaust residue as soon as practical to avoid

staining or damaging of the ﬁ nish.

It is possible to remove wrinkles from the covering. Use a

covering on low heat, and place a piece of paper between

the iron and covering to help disperse the heat from

the iron to avoid damaging the covering. Always start

with low heat and work toward a hiogher heat to avoid

damaging the covering.

A section of covering has been provided if there is a need

to make any repairs to the covering.

 TRANSPORT UND LAGERUNG

Mit der Zeichnung aus drei Ansichten am Ende des

Handbuchs lässt sich ermitteln, wie viel Platz zum

Transport und zur Lagerung des Modells benötigt

wird. Das Modell kann demontiert werden, daher ist

der erforderliche Platz variabel. Die Empfehlung einer

Flügeltasche wird empfohlen, um diese Oberﬂ ächen bei

Transport und Lagerung zu schützen. Die Steuerhörner

und Gestänge können zudem Schäden an benachbarten

Oberﬂ ächen verursachen, auch wenn sie in Taschen

gelagert sind. Oberﬂ ächen stets so platzieren, dass

die Oberseiten aneinander liegen, um Schäden durch

Steuerhörner und Gestänge zu vermeiden.

 HINWEISE ZUR BESPANNUNG

• Bei der bei diesem Modell verwendeten Abdeckung

sind Farben und Markierungen direkt auf die

Abdeckung gedruckt.

• Die Abdeckung ist selbstklebend, und ein Erwärmen

wird nicht empfohlen, da die Wärme die Abdeckung

beschädigen könnte.

• Verwenden Sie nur milde Reiniger für die bedruckte

Folie. Als aggressiver Reiniger der noch zu empfehlen

ist, empfehlen wir denaturierten Alkohol. Prüfen

Sie vorher unbedingt an unauffälliger Stelle die

Verträglichkeit. Wiederholte / verlängerte Anwendung

entfernt die Farbe.

• Verwenden Sie Klebeband nur mit äußerster Vorsicht.

Bis auf Kreppband entfernt alle Klebebänder die Farbe.

Dieses gilt insbesondere für die Kanten.

• Vermeiden Sie den Kontakt mit Kraftstoff, insbesondere

Alkohol-basierte Kraftstoffe mit Nitromethan.

• Entfernen Sie Abgasrückstände schnellstmöglich um

ein Verfärben oder Beschädigen der Bespannung zu

vermeiden.

Es ist möglich, die Falten von der Abdeckung zu

entfernen. Ein Heißsiegelgerät bei schwacher Hitze

verwenden und ein Stück Papier zwischen das Gerät und

die Abdeckung legen, um die Hitze vom Heißsiegelgerät

zu verteilen und so Schäden an der Abdeckung zu

vermeiden. Immer bei mit geringer Hitze beginnen und

auf eine höhere Hitze gehen, um die Abdeckung nicht zu

beschädigen.

Ein Stück Abdeckung wurde bereitgestellt, falls

Reparaturen an der Abdeckung erforderlich sind.

 TRANSPORT ET STOCKAGE

Utilisez le schéma à 3 vues à l’arrière de ce manuel

pour déterminer l’espace nécessaire pour transporter

et stocker votre maquette. La maquette peut être

démontée, l’espace nécessaire peut donc varier. Nous

vous conseillons d’utiliser un sac à ailes pour protéger

ces surfaces lors du transport et du stockage. Les

renvois de commande et tringleries peuvent également

endommager les surfaces proches même si rangés dans

des sacs de rangement. Placez toujours ces surfaces

de manière à ce que les sommets soient ensemble

pour prévenir tout dommage causé par les renvois de

commande et les tringleries.

 REMARQUES RELATIVES À L’ENTOILAGE

IMPRIMÉ

• L’entoilage utilisé sur votre maquette a les couleurs et

les marquages imprimés directement sur l’entoilage.

• L’entoilage a un endos autocollant, et il n’est pas

recommandé d’utiliser de la chaleur car cela peut

endommager l’entoilage.

• Utilisez uniquement des produits de nettoyage doux

sur la surface du ﬁ lm. L’alcool dénaturé est le produit

le plus agressif que vous pouvez utiliser, mais nous

vous conseillons de procéder d’abord à un essai

sur une partie de surface non visible. Une utilisation

fréquente endommagera la peinture présente sur le

ﬁ lm.

• Utilisez du ruban adhésif avec précautions. Tout autre

adhésif que de l’adhésif de masquage endommagera

la décoration, surtout au niveau des angles.

• Evitez le contact avec du carburant brut, surtout les

carburants à base d’alcool contenant du nitrométhane.

• Essuyez les résidus de carburant immédiatement

après le vol aﬁ n d’éviter d’endommager la ﬁ nition.

Il est possible de retirer les faux-plis de l’entoilage.

Utilisez un entoilage à feu doux et placez un morceau

de papier entre le fer à repasser et l’entoilage pour

aider à disperser la chaleur du fer à repasser pour éviter

d’endommager l’entoilage. Commencez toujours à feu

doux et augmentez la chaleur pour éviter d’endommager

l’entoilage.

Une partie de l’entoilage a été fournie, au cas où il

faudrait effectuer des réparations sur l’entoilage.

 TRASPORTO E DEPOSITO

Fare riferimento al trittico riportato sul retro di questo

manuale per determinare lo spazio necessario al

trasporto e all’immagazzinaggio del modello. Il modello

può essere smontato e, di conseguenza, lo spazio

necessario può variare. È consigliabile usare delle borse

alari per proteggere queste superﬁ ci durante il trasporto

e l’immagazzinaggio. Squadrette e rinvii possono

danneggiare le superﬁ ci circostanti anche all’interno delle

borse. Per prevenire questo problema, sistemare sempre

le superﬁ ci facendo combaciare le superﬁ ci superiori.

 NOTE SUL RIVESTIMENTO STAMPATO

• Colori e marcature di questo modello sono stampati

direttamente sul rivestimento.

• Il retro del rivestimento è autoadesivo e non è quindi

consigliabile avvicinarvi fonti di calore che potrebbero

danneggiarlo.

• Usare solo detergenti delicati sulla ﬁ nitura stampata.

L’alcol denaturato è il detergente più aggressivo che

noi consigliamo, però conviene sempre provarlo prima

su di un’area del rivestimento che è poco visibile. Un

uso prolungato potrebbe rimuovere la vernice.

• Usare il nastro adesivo con attenzione. Qualsiasi cosa

che sia di più di un nastro a bassa adesività, potrebbe

staccare la ﬁ nitura specialmente sui bordi.

• Evitare il contatto con del combustibile, specialmente

se a base di alcol e contenente nitrometano.

• Togliere i residui dello scarico appena possibile per

evitare la formazione di macchie o il danneggiamento

della ﬁ nitura.

È possibile rimuovere le increspature dal rivestimento.

Utilizzare un ferro da stiro a bassa temperatura e

posizionare un pezzo di carta tra il ferro e il rivestimento

per migliorare la dispersione di calore dal ferro ed evitare

di danneggiare il rivestimento. Iniziare sempre con

una temperatura bassa e aumentare gradualmente la

temperatura per evitare di danneggiare il rivestimento.

È stata fornita una sezione di rivestimento nel caso sia

necessario effettuare eventuali riparazioni al rivestimento.

11 EN

P-51D Mustang 20cc

 FLAP INSTALLATION

1. Remove the ﬂ aps and aileron from the wing panel.

2. Locate the two ﬂ ap control horns. When installed, the concave

portion of the horn (as indicated in the drawing) will face

toward the top of the ﬂ aps.

3. Use a pin vise and 1/16-inch (1.5mm) drill bit to remove any

paint from the hole in the ﬂ ap control horn for the clevis.

Prepare all the control horns at this time.

4. Use medium-grit sandpaper to remove any paint from the

ﬂ ap control horn where it ﬁ ts into the ﬂ ap. Clean the sanded

area using a paper towel and isopropyl alcohol to remove any

debris or oils. Removing the paint provides the surface texture

necessary for the epoxy to bond to.

5. Remove the ﬂ ap from the wing. Run your ﬁ nger down

the leading edge of the ﬂ ap to locate the area for the ﬂ ap

control horn. Use a hobby knife and #11 blade to remove

the covering, exposing the slot for the control horn. Use

15-minute epoxy to glue the ﬂ ap control horn in position.

Remove any excess epoxy using a paper towel and isopropyl

alcohol.

6. Run your ﬁ nger down the lower surface leading edge of the

ﬂ ap to locate the areas for the ﬂ ap hinges. Use a hobby knife

and #11 blade to remove the covering, exposing the holes

for the ﬂ ap hinges. Test ﬁ t the hinges to the ﬂ ap. Do not use

any adhesives now. Slide the hinge into position. Position as

shown, checking to make sure it can move freely.

7. Run your ﬁ nger down the lower surface trailing edge of the

wing to locate the areas for the ﬂ ap hinges. Use a hobby knife

and #11 blade to remove the covering, exposing the holes for

the ﬂ ap hinges. Check the ﬁ t of the ﬂ ap to the wing. The top

of the ﬂ ap will align to the top of the wing. It will also line up

with the aileron. The ﬂ ex point of the hinges will align with

the hinge line of the ﬂ aps when installed properly. Test the

operation of the ﬂ ap to make sure the hinges are properly

aligned and the ﬂ ap movies freely.

8. Apply a small amount of petroleum jelly to the ﬂ ex point of

the hinge to prevent epoxy from entering the hinge.

 Use care to only apply the petroleum jelly to the flex

point. If applied to the hinge portion, it could cause the epoxy

not to adhere to the hinge, resulting in a poor glue joint.

 The flaps must be positioned to the wing before the

epoxy begins to cure. Make sure to read through all the steps

before mixing any epoxy. Glue only one flap at a time to

allow enough working time to properly install the hinges.

 Use 15-minute or 30-minute epoxy to allow

enough working time during the hinge installation.

9. Remove the ﬂ ap from the wing and remove the hinges. Apply

epoxy into each of the holes in the ﬂ ap.

 Do not use an excessive amount of epoxy when gluing the

hinges so that it expels from the hinge. Also make sure to use

enough epoxy so it securely adheres the hinge to the surfaces.

12EN

10. Apply epoxy to each hinge where it will be inserted into the

ﬂ ap. Insert the hinges as shown in Step 6.

 AILERON INSTALLATION

15. Use a pin vise and 1/16-inch (1.5mm) drill bit to drill a hole

in the center of each hinge slot. Drill the hole 1/4-inch (6mm)

deep into the wood.

11. Apply epoxy to each hinge where it will be inserted into the

wing.

16. Place a T-pin in the center of each of the three hinges.

12. Apply epoxy into each of the holes in the wing. 17. Slide the hinges into position in the aileron with the T-pin

resting against the edge of the control surface. The slot in the

hinge must align with the hole drilled in the aileron.

13. Fit the ﬂ ap to the wing as shown in Step 7. Check that the

ﬂ ap can move freely and the hinges are all aligned properly.

Use low-tack tape to hold the ﬂ ap in position until the epoxy

fully cures.

18. Hold the aileron to the wing. Use a felt-tipped pen to mark the

center of the hinges on the wing. Use a pin vise and 1/16-

inch (1.5mm) drill bit to drill the holes in the wing.

14. Use a paper towel and isopropyl alcohol to remove any

excess epoxy before it can fully cure. Use care not to get

epoxy in the moving part of the hinge or between the ﬂ ap and

wing. Continue once the epoxy has fully cured for both sets of

ﬂ ap hinges.

 Repeat this section for the remaining flap installation.

19. Check the gap between the wing tip and aileron.

13 EN

P-51D Mustang 20cc

15/16 inch

(24mm)

20. Check the gap between the ﬂ ap and aileron. The gaps in

Steps 19 and 20 must be equal before applying CA to the

hinges.

 When the flap is lowered and the aileron is in the

full down position, there may be some interference

between the flap and aileron. In flight, the aileron will

not deflect far enough to interfere with the flap.

25. Run your ﬁ nger along the bottom of the aileron to locate the

area for the ﬂ ap control horn. Use a hobby knife and #11

blade to remove the covering, exposing the slot for the control

horn.

22. Allow the CA to cure for 10 to 15 minutes. Gently pull on the

ﬁ xed surface and control surface to make sure the hinges are

glued securely. If not, apply additional CA to secure each of

the hinges.

27. Test ﬁ t the aileron control horn to the aileron. Place tape

around the slot in the aileron for the aileron control horn.

21. Apply thin CA to the top of each of the hinges. Make sure to

fully soak the hinges so the CA can wick into the hinge and

bond to the surrounding wood.

 Use thin CA so it wicks into the hinge. A thicker CA

will not wick into the hinge properly. Do not to allow the

CA to run over the covering on the wing and aileron.

26. Locate the two silver aileron control horns. Use medium-grit

sandpaper to remove any paint from the bottom of the control

horn where it ﬁ ts into the aileron.

23. Move the aileron through its range of travel to break in the

hinges.

24. Check both the up and down movement of the hinges before

proceeding.

28. Check that the horn is 90-degrees to the surface of the

aileron. If not, lightly trim the hole in the aileron to reposition

the control horn.

29. Remove the aileron control horn from the aileron. Apply epoxy

to the area of the control horns that ﬁ ts into the slots. Use

enough epoxy so the control horns will be fully bonded to the

ﬁ xed surfaces.

14EN

30. Remove the control horns from the control surfaces. Apply

epoxy to the slot in the aileron and ﬂ ap. Make sure the epoxy

gets into the slot for a good bond between the surfaces and

control horn.

31. Before the epoxy fully cures, remove the tape from around

the control horn. This will allow the epoxy to ﬂ ow around the

control horn, creating a small ﬁ llet between the control horn

and surface for a ﬁ nished look and secure bond.

 Repeat this section for the remaining aileron installation.

 AILERON SERVO INSTALLATION

32. Use a hobby knife or other sharp tool to puncture the covering

at the screw holes that will secure the cover to the wing. Also

remove the covering for the aileron servo arm in the cover.

33. Use a hobby knife with a #11 blade to remove the covering

for the aileron servo arm in the cover.

34. Place the cover back into position. Use a pin vise and 1/16-

inch (1.5mm) drill bit to drill the mounts for the servo covers.

Use care not to drill through the covering on the top of the

wing.

35. Thread an M2 x 10 sheet metal screw into each hole

using a #1 Phillips screwdriver. Remove the screws before

proceeding.

36. Apply a small amount of thin CA to harden the threads

made in the previous step. Allow the CA to fully cure before

installing the aileron servo cover.

 Prepare the flap servo covers at this time as well.

37. Use a pin vise and 5/32-inch (2mm) drill bit to drill the

holes for the servo mounting screws. Make sure to harden

the holes using the technique outlined in Steps 30 and 31.

Use the screws provided with the servo and a #1 Phillips

screwdriver when installing the screws.

38. Secure the servo to the cover using a #1 Phillips screwdriver

and the screws provided with the servo.

39. Secure a 12-inch (300mm) servo extension to the servo using

a commercially available fastener (SPMA3054).

15 EN

P-51D Mustang 20cc

5/8 inch

(16mm)

40. Center the servos, then secure the servo arm so it is

perpendicular to the servo centerline. Use side cutters to

remove any arms that do not protrude to the outside of the

cover.

41. When attaching the linkage to the aileron servo arm, use the

hole in the arm that is 5/8-inch (16mm) from the center of

the arm.

 The suggested measurements will result in a scale roll

rate. A longer servo arm can be used for a faster roll rate.

42. Tie or tape the string located inside the wing to the end of the

servo lead.

43. Use the string to pull the servo lead through the wing and out

at the root.

44. Secure the servo to the wing using four M2 x 10 sheet metal

screws. Use a #1 Phillips screwdriver to tighten the screws.

45. Slide a silicone tube on the clevis. Thread the clevis on the

inch (100mm) pushrod. Allow 1/16 inch (1.5mm) of the

threads on the pushrod protrude between the forks of the

clevis.

46. Attach the clevis to the inside hole on the aileron control horn.

47. Center the aileron servo using the radio system. With the

aileron centered, use a felt-tipped pen to mark the pushrod

where it crosses the outer hole of the servo arm.

48. Remove the clevis from the control horn. Use pliers to bend

the pushrod at the mark made in the previous step. Use side

cutters to cut the end of the pushrod so the inside dimension

measures 1/4 inch (6mm).

49. Insert the pushrod into the outer hole on the servo arm.

16EN

5/8 inch

(16mm)

50. Slide the pushrod keeper on the pushrod wire.

51. Slide the keeper tightly against the servo arm. Use pliers to

snap the keeper on the pushrod wire.

52. Check the operation of the aileron using the radio system.

Trim the servo cover if the keeper or pushrod wire hits

the cover during the operation of the aileron. Slide the

clevis retainer over the forks of the clevis. Apply a drop of

threadlock on the threads near the clevis, then tighten the nut

against the clevis using pliers.

 Repeat this section for the remaining

aileron servo installation.

54. Use a pin vise and 5/32-inch (2mm) drill bit to drill the

holes for the servo mounting screws. Make sure to harden

the holes using the technique outlined the aileron servo

installation. Use the screws provided with the servo and

secure the servo to the cover. Center the ﬂ ap servo using the

radio system. Attach the servo arm to the servo using the

hardware included with the servo. Remove any arms that may

interfere with the operation of the servo.

55. When attaching the linkage to the aileron servo arm, use the

hole in the arm that is 5/8-inch (16mm) from the center of

the arm.

56. Check the ﬁ t of the M3 x 10 pan head screws through the ﬂ ap

mount. Measure the length protruding from the mount. If this

measures more than 5/32 inch (4mm), use washers under

the head of the screw to prevent the screw from penetrating

through the wing sheeting.

57. Mount the ﬂ ap servo in the wing using the M3 x 14 pan head

sheet metal screws and a #2 Phillips screwdriver.

 We recommend installing and removing the flap servo, then

hardening the screw holes in the wing with thin CA. This will help

reduce the change of puncturing the wing using only the screws.

58. Slide a silicone tube on the clevis. Thread the clevis on the

inch (100mm) pushrod. Allow 1/16 inch (1.5mm) of the

threads on the pushrod protrude between the forks of the

clevis.

 FLAP SERVO INSTALLATION

53. Check the ﬁ t of the ﬂ ap servo mount in the wing. There is a

right and left mount and will only ﬁ t in the correct wing panel.

59. Attach the clevis to the ﬂ ap control horn.

17 EN

P-51D Mustang 20cc

60. Pull the ﬂ ap servo extension through the wing so it exits near

the aileron servo lead.

61. Place the ﬂ ap in the MID ﬂ ap position according to the control

throws in this manual.

62. Use the radio system to move the servo to the MID ﬂ ap

position. Use a felt-tipped pen to mark the pushrod where it

crosses the outer hole in the servo arm.

 Set the throw of the flap servo to 0% in both the

UP and DOWN positions to center the servo. The flap

throw can be adjusted by increasing these values.

63. Remove the clevis from the control horn. Use pliers to bend

the pushrod at the mark made in the previous step. Use side

cutters to cut the end of the pushrod so the inside dimension

measures 1/4 inch (6mm). Slide the pushrod keeper on the

pushrod wire. Slide the keeper tightly against the servo arm.

Use pliers to snap the keeper on the pushrod wire.

64. Check the operation of the ﬂ ap using the radio system. Set

the switch to the UP ﬂ ap position. Adjust the linkage or radio

system as necessary to set the throw.

65. Check the operation of the ﬂ ap using the radio system. Set

the switch to the FULL ﬂ ap position. Adjust the linkage or

radio system as necessary to set the throw.

66. Secure the ﬂ ap servo cover in position using four M2 x 10

sheet metal screws. Make sure the holes for the ﬂ ap servo

covers screws have been prepared before installing the cover.

 LANDING GEAR STRUT AND DOOR ASSEMBLY

67. Slide the gear door linkage mount on the landing gear strut.

The ﬂ at area on the mount will face the wheel mount arm.

68. Slide a #10 washer on the 10-32 x 1

inch socket head cap

screw.

69. Slide the screw through the wheel, then slide the plastic

spacer on the screw.

18EN

70. Thread the screw into the wheel mount arm. Make sure not

to overtighten the screw, preventing the wheel from rotating.

Use an M3 x 4 setscrew and 1.5mm hex wrench to secure

the screw to the arm. Use a drop of threadlock on both the

screw and setscrew before tightening.

71. Place the gear door linkage mount near the indentation on the

gear door. Transfer the locations for the mounting screws to

the gear door.

72. Use a pin vise and 1/8-inch (3mm) drill bit to drill the holes

for the linkage mount in the door. Make sure the holes are

centered vertically in the indentation.

73. Mount the linkage mount to the gear door using two M2.5 x 5

button head cap screws and 2mm hex wrench.

74. Attach the linkages to the linkage mount using two M2.5 x 8

button head cap screws and a 2mm hex wrench. Make sure

the linkages can move freely when attached to the mount.

 FIXED GEAR INSTALLATION

 Skip this section when planning retract

installation in the P-51D Mustang.

75. Use a hobby knife with a #11 blade to remove the covering

exposing the mounts for the ﬁ xed landing gear.

76. Slide the strut mounting stud into the landing gear mount.

Use an M3 x 6 setscrews and 2mm hex wrench to secure the

stud in the mount. Tighten the setscrew onto the ﬂ at area on

the stud. The end of the stud will protrude 1/16 inch (1.5mm)

from the end of the mount. Use threadlock on the setscrew to

prevent it from vibrating loose.

77. Secure the landing gear mount using four M3 x 20 socket

head cap screws. Make sure to place a drop of threadlock on

each screw before placing them in position. Use a 3mm hex

wrench to tighten the screws.

78. Slide the strut on the landing gear wire. Use three M3 x 3

setscrews and a 1.5mm hex wrench to temporarily attach the

strut to the stud..

79. Check that there is a slight amount of toe-in (approximately

1-degree). Adjustments can be made by loosening the three

setscrews on the strut near the mount using a 1.5mm hex

wrench.

 The amount of toe-in shown has been

exaggerated so it can be seen clearly in the photo.

 Always use threadlock on metal-to-metal fasteners.

19 EN

P-51D Mustang 20cc

80. Test ﬁ t the gear door hinge in the slot near the landing gear

mount. Once the ﬁ t has been checked, use a small amount of

5-minute epoxy to glue the hinge in the slot. Allow the epoxy

to fully cure before proceeding.

81. Attach the gear door linkages to the mount on the strut using

two M3 x 8 button head screws and 2mm hex wrench.

82. Slide the mount on the strut until there is maximum clearance

between the door and wheel. Use an M3 x 3 setscrew and

1.5mm hex wrench to secure the mount to the strut.

 Repeat this section for the remaining fixed gear installation.

 RETRACT INSTALLATION

 Skip this section of the manual if the fixed

gear has been installed on your model.

83. Use a hobby knife and #11 blade to remove the covering from

the retract openings in the wing. Trim the covering inside the

opening.

85. Secure a 9-inch (230mm) servo extension to the servo using

a commercially available fastener (SPMA3054).

86. Guide the servo lead through the wing. We recommend

removing the ﬂ ap servo cover to make the installation easier.

87. The retract lead will exit the wing root with the ﬂ ap and

aileron servo leads.

 Make sure to mark each lead for easier connection

when assembling the model before flight.

88. Secure the retract in the wing using the hardware included

with the retract. Place a drop of threadlock on each of the

screws before installing them in the retract. Use a 2mm hex

wrench to tighten the screws.

 It may be necessary to use the spacers included with

the retracts to make sure there is no torsional stress on the

retract frame when tightened into position. Torsional stress can

sometimes cause intermittent operation of the retract unit.

89. Slide the retract strut into the retract frame.84. Remove the wire strut and bushing from the retract frame.

20EN

90. Check that there is a slight amount of toe-in (approximately

1-degree). Adjustments can be made by loosening the

setscrews using a 1.5mm hex wrench.

 The amount of toe-in shown has been

exaggerated so it can be seen clearly in the photo.

91. Retract the landing gear. Use a 2mm hex wrench to tighten

the setscrews, securing the strut in the retract frame.

 Always use threadlock on metal-to-metal fasteners.

92. Test ﬁ t the gear door hinge in the slot near the landing gear

mount. Once the ﬁ t has been checked, use a small amount of

5-minute epoxy to glue the hinge in the slot. Allow the epoxy

to fully cure before proceeding.

93. Attach the gear door linkages to the mount on the strut using

two M3 x 8 button head screws and 2mm hex wrench. Do not

over-tighten the screws, as the linkages must move freely for

the gear door to operate properly.

95. Use a 1.5mm hex wrench to tighten the setscrew in the gear

door mounts. Check the operation of the retract and door.

Adjust the position of the mount as necessary so the gear

door fully closes, yet does not restrict the operation of the

retract.

 Do not over-tighten the setscrews as this will damage

the gear door mounts or restrict the movement of the strut.

 Repeat this section for the remaining retract installation.

 RADIO INSTALLATION

96. Move the canopy latch toward the front of the fuselage. Lift

the canopy hatch from the fuselage at the rear. Slide the

hatch back and remove it from the fuselage. Set it aside in a

safe location.

97. Install the grommets and eyelets in the servos. Follow any

instructions included with the servo. Prepare both elevator

and rudder servos.

98. Install the rudder and elevator servos in the fuselage with the

servo output towards the front of the fuselage. Make sure to

prepare the holes as outlined in the aileron servo installation

section of this manual.

 The rudder servo is the middle servo.

94. Position the gear door mount 3/4 inch (19mm) below the

scissor mount bracket.

La pagina sta caricando ...

Hangar 9 HAN2820 Manuale del proprietario

Marca: Hangar 9

Modello: HAN2820

Categoria: Giocattoli telecomandati

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Hangar 9 HAN2820 Owner's manual
français: Hangar 9 HAN2820 Le manuel du propriétaire
Deutsch: Hangar 9 HAN2820 Bedienungsanleitung

Hangar 9 HAN2820 Manuale del proprietario

Hangar 9 HAN2820 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti