Agria 0400 Manuale del proprietario

4235

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No. 998 745 04.15



Multi-Purpose MachineMulti-Purpose Machine

Multi-Purpose Machine

400P400P

400P

Operating InstructionsOperating Instructions

Operating Instructions

Translation of the original operating instructionsTranslation of the original operating instructions

Translation of the original operating instructions

2 agria Multi-Purpose Machine 400P

Symbols, Name Plate

Please complete:

Machine Type No.........................

Identification No.

....................................................

Engine Type:................................

Engine No....................................

Date of Purchase: .......................

For name plate, refer to p3/fig. A/9.

For engine type and number, refer to

p3/fig. B/6.

Please state these data when order-

ing spare parts to avoid wrong deliv-

eries.

Only use original agria spare parts!

Specifications, figures and dimen-

sions stated in these instructions are

not binding. No claims can be derived

from them. We reserve the right for

improvements without changing these

instructions.

This delivery comprises:

l

Operating instructions

l

Multi-purpose base machine

l

Tool kit

Symbols:

Warning – Danger

Important information

Fuel

Choke

Oil

Mowing drive

Travelling drive

Forward

Reverse

Open (unlocked)

Closed (locked)

PTO

è - Serviceç= please con-

tact Your specialised agria-workshop

agria Multi-Purpose Machine 400P 3

A

B

Designation of Parts

4 agria Multi-Purpose Machine 400P

Designation of Parts

Figure A

1 Pto speed engagement lever

2 Linkage for front attachments

3 Transmission oil plug (filling and checking oil level)

4 Linkage for rear attachments

5 Grooves on wheel shaft

6 Wheel shaft

7 Gearbox cover/Transmission oil drain opening

8 Pto/pto guard

9 Name plate (machine identification no.)

10 Handlebar

11 V-belt guard (V-belt clutch)

12 Drive wheel

13 Drive-wheel detent spring

14 Guard

Figure B

1 Air filter

2 Carburetor

3 Fuel tank cap

4 Fuel tank

5 Choke lever

6 Engine type no.

7 Starter handle

8 Cooling air-screen

9 Exhaust with guard

10 Spark plug/spark plug connector

11 Engine oil filler plug and dip-stick

12 Engine oil drain plug

13 Fuel tap

agria Multi-Purpose Machine 400P 5

Index

Amount of Delivery ..........................2

Symbols, Name Plate......................2

Designation

of Parts.............................. 3, 54

Recommendations

Lubricants, Anti-Corrosive Agents ..6

Fuel ..................................................6

Maintenance and Repair .................6

Unpacking and Assembly ..... 7

1. Safety Instructions....... 8–12

2. Specifications

Multi-purpose Machine ..................13

Noise Level ....................................13

Vibration Acceleration Value..........13

Engine............................................14

Operation on Slopes......................14

3. Devices and Operating

Elements

Engine............................................15

Speed Control Lever......................16

Safety circuit ..................................16

Choke.............................................16

Fuel Tap .........................................17

Clutch.............................................17

Main Gearbox ................................18

Drive Wheels .................................20

PTO................................................25

Stand .............................................25

Steering Handle.............................26

Attachments...................................27

Hoeing, Ridging ....................... 30-32

4. Commissioning and

Operation

Commissioning the Machine .........33

Starting the Engine........................34

Shutting off the Engine ..................35

Working..........................................36

5. Maintenance

Engine............................................37

Air Filter .........................................38

Fuel System...................................39

Spark Plug .....................................40

Cooling System .............................40

Governor ........................................41

Exhaust..........................................41

Speed Control................................41

Carburetor Settings .......................41

Machine .........................................42

Drive-wheels ..................................42

Safety circuit ..................................43

Clutch Play.....................................43

General ..........................................45

Cleaning.........................................45

Storage ..........................................46

6. Troubleshooting.......... 48–49

Electrical Wiring ................... 50

Lubrication Chart ................. 50

Varnishes, Wear Parts.......... 51

Inspection and

Maintenance Chart............... 52

Conformity Declaration ....... 55

Note fold-out pages!

Fig. A and B ............................ 3

Fig. C and D .......................... 54

1

2

3

4

5

6

6 agria Multi-Purpose Machine 400P

Recommendations

Lubricants and

Anti-Corrosive Agents:

Use the lubricants specified for engine

and gearbox (see “Specifications”).

We recommend using Bio-lubricating

oil or Bio-lubricating grease for “open”

lubrication points or nipples (as speci-

fied in the operating instructions).

We recommend using Bio-slushing oil

to preserve machines and attachments

(do not apply on painted covers). You

can brush or spray the oil.

Anti-corrosive agents are environmen-

tally friendly and degrade fast.

Using ecologically safe Bio-lubricants

and Bio-anti-corrosives, you contribute

to environmental protection and to the

wellbeing of humans, animals and

plants.

Fuel:

This engine runs smoothly on commer-

cial unleaded regular and supergrade

petrol (including E10).

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residue from depos-

iting in the caburetor, fuel filter, and tank.

Or add a fuel stabilizer to the fuel.

For further instructions see “Engine

Preservation”.

Maintenance and Repair:

The trained mechanics of your agria

workshop expertly carry out any main-

tenance and repair work.

You should only carry out major main-

tenance work and repairs on your own,

if you have the proper tools and knowl-

edge of machines and internal combus-

tion engines.

Do not hammer against the flywheel with

a hard object or metal tools as it might

crack and shatter in operation, causing

injuries and damage. Only use suitable

tools to pull off the flywheel.

agria Multi-Purpose Machine 400P 7

Unpacking and Assembly

E

1 Base machine

2 Steering handle

3 Steering handle attachment bolt

4 Hex nut

5 Drive wheels (accessory items)

l

Open the box top.

l

Cut the two rear corners open and

fold down the side.

l

Remove the steering handle attach-

ment bolt (3 + 4).

l

Pivot the steering handle (2) up-

wards. Then attach and tighten the bolt

(3 + 4).

l

Attach the drive wheels (see instruc-

tions on page 20).

l

Starting-up

See instructions on page 33.

8 agria Multi-Purpose Machine 400P

1. Safety Instructions

1

Before starting the engine, read the op-

erating instructions and note:

Warning

This symbol marks all paragraphs in

these operating instructions which affect

your safety. Pass all safety instructions

on to other users and operators.

Due Use

The multi-purpose machine is a hand-

controlled automatic single-axle ma-

chine which can power and/or pull vari-

ous implements approved by the manu-

facturer. Areas of application are for such

as turning over the ground, mowing

grass and meadowland, snow clearance

and sweeping (due use).

Any other type of operation is consid-

ered undue. The manufacturer is not li-

able for any damages resulting from

undue use, for which the risk lies with

the user alone.

When the multi-purpose machine is

used on public roads, the local national

road traffic rules must be observed, e.g.

reflectors, lights.

The multi-purpose machine is not in-

tended for use with a trailer on public

roads or as as a tractor unit without im-

plements.

Due use includes compliance with

manufacturer’s instructions on opera-

tion, maintenance and repair.

Any unauthorized changes to the ma-

chine render manufacturer liability null

and void.

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The respective national accident preven-

tion regulations have to be adhered to,

as well as all other generally accepted

rules governing operational safety, oc-

cupational health and road traffic regu-

lations.

When driving on public roads, you have

to observe the current traffic code.

Accordingly, check the machine for road

and operational safety each time you

take up operation.

Only persons familiar with the tractor and

instructed on the hazards of operation

are allowed to use, maintain and repair

the tractor.

Teenagers younger than 16 years are

not allowed to operate the machine!

Only work in good light and visibility.

Operator’s clothes should fit tight. Avoid

wearing loose fitting clothes. Wear solid

shoes.

Note the warning and instruction signs

on the tractor for safe operation. Com-

ply for your own safety.

When transporting the tractor on vehi-

cles or trailers outside the area to be

cultivated, ensure that the engine is

turned off.

Careful with rotating tools – keep at a

safe distance!

Foreign powered parts shear and crush!

Riding on the attachment during opera-

tion is not permitted.

agria Multi-Purpose Machine 400P 9

1. Safety Instructions

1

Mounted or trailed attachments affect

the tractor’s driving, steering, braking,

and tipping characteristics. Therefore,

ensure that steering and braking func-

tions are sufficient. Match operating

speed to conditions.

Do not change settings of governor. High

engine speed increases risk of acci-

dents.

Working Area and

Dangerous Area

The user is liable to third parties work-

ing within the tractor’s working range.

Staying in hazardous area is not per-

mitted.

Check the immediate surroundings of

the tractor before you start it. Watch out

for children and animals.

Before you start work, clear the area

from any foreign object. During opera-

tion, always watch out for further objects

and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to enclo-

sures to prevent damage to tools.

Operation and

Safety Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency.

Ensure that all guards in place.

With no attachment mounted, make

sure PTO-shaft is covered with the pro-

tective cap.

Starting the engine

Do not start the engine in closed rooms.

The carbon monoxide contained in the

exhaust fume is extremely toxic when

inhaled.

Before you start the engine set all con-

trols to neutral or idling position.

When starting the engine, do not step

in front of the machine and the attach-

ment.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

Operation

Never leave the operator’s position at the

steering handle while tractor is at work.

Never adjust the handles during work -

danger!

For any operation do not leave the op-

erator’s position as defined by the steer-

ing handle, especially not when you turn

the machine.

Riding on the attachment during opera-

tion or in transport is not permitted.

If blockages occur in the attachment,

turn off the engine and clean the attach-

ment with an appropriate tool.

In case of damage to the multi-purpose

machine or to the attachment, immedi-

ately turn off the engine and have it re-

paired.

If steering causes problems, immedi-

ately bring the machine to a halt and

turn it off.

Have the malfunction removed without

delay.

10 agria Multi-Purpose Machine 400P

1. Safety Instructions

1

To prevent the machine from sliding on

slopes make sure it is secured by an-

other person using a bar or a rope. This

person must be located at a higher po-

sition than the vehicle at a safe distance

from the attachment at work.

If possible, always work horizontally to

the slope.

End of Operation

Never leave the multi-purpose machine

unattended with the engine running.

Before you leave the machine, turn off

the engine. Then close fuel taps.

Secure the machine against unauthor-

ized use. If tractor is equipped with an

ignition key, remove the key. For all other

versions, remove the spark plug connec-

tor to secure the tractor.

Attachments

Only mount attachments with the engine

and PTO switched off.

Always use appropriate tools and wear

gloves when changing attachments and

parts thereof.

To fit and remove attachments, bring the

support leg into proper position and en-

sure stability.

Secure the machine and attachments

against rolling off (parking brake, wheel

chocks).

Beware of injuries while coupling attach-

ments.

Couple the attachments as specified

and only couple at specified points.

Secure the machine and attachment

against unauthorized use and rolling off

when you leave the machine. If neces-

sary, install transport or safety devices

to provide protection.

Hoeing Attachment

Adjust the guards in such a way that only

the sets of blades penetrating the soil

are not covered.

When hoeing, make sure the depth bar

is adjusted properly.

Mowing Attachment

Handle with care! Sharp blades of the

cutter bar may cause injuries when han-

dled improperly! Remove knife guards

only for mowing and refit immediately

after work has finished.

For transport and storage always fit the

knife guards. Secure finger bars addi-

tionally with tension springs.

Do not transport the removed cutter bar

without knife guards.

When fitting/removing the cutter bar,

make sure all blades are protected by

the knife guards.

To exchange the knife and to fit/remove

the knife driver, make sure that you turn

screws and bolts away from the cutting

blades to remove them.

To grind the mowing knives, always wear

safety goggles and gloves.

Weights

Always fit weights properly and at speci-

fied points.

Maintenance

Never carry out any maintenance or

cleaning while the engine is running.

Before you work on the engine, always

remove spark plug connector (petrol

engine only).

agria Multi-Purpose Machine 400P 11

1. Safety Instructions

1

Check regularly and, if necessary, re-

place all guards and tools subject to

wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use

proper tools when exchanging cutting

tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. coupling de-

vices)!

Keep the machine and the attachment

clean to avoid risk of fire.

Check nuts and bolts regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

guards and adjust them properly after

maintenance and cleaning.

Only use original agria spare parts. All

other conventional spare parts must cor-

respond to quality and technical require-

ments specified by agria.

Storage

It is not allowed to store the machine in

rooms with open heating.

Never park the machine in closed rooms

with fuel left in tank. Fuel vapours are

hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed rooms.

Extreme danger of intoxication! For the

same reason, also replace damaged

exhaust pipes immediately.

Be careful when dealing with fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot en-

gine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine switched off

and cooled down.

Do not spill any fuel, use a proper filling

device.

In case of fuel-spillage, pull the machine

away from the spillage before you start

the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Store anti-corrosive agents and stabi-

lizing liquids out of reach of children. If

sickness and vomiting occur, see a doc-

tor. If fuel has contacted eyes, rinse them

thoroughly, avoid inhaling of vapours.

Read and observe enclosed instruc-

tions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark forma-

tion or flames. If necessary, dispose of

tins in hazardous waste deposits.

Be careful when draining hot oil, dan-

ger of burns.

Make sure oil used is of specified qual-

ity. Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Tyres and Tyre Pressure

When working on the tyres, make sure

the machine is parked properly and se-

cured against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the ap-

propriate tools.

Regularly check air pressure in the tyres.

Excessive pressure may cause bursts.

12 agria Multi-Purpose Machine 400P

1. Safety Instructions

1

When adding weight, make sure the tyre

pressure is correct.

Re-tighten bolts of drive-wheels or check

tightness when doing maintenance

work.

Electrical System and Battery

When working on the electrical system,

make sure the battery is disconnected

(negative terminal) (for tractors

equipped with battery).

Make sure to connect the battery prop-

erly – first connect the positive terminal

and then negative terminal. Disconnect

in reverse order.

Be careful with battery gases – explo-

sive!

Avoid spark discharge and open flames

near batteries.

Remove plastic cover (if equipped) to

recharge battery and to prevent highly

explosive gases from building up.

Careful when handling battery acid!

Only use specified circuit breakers. If the

circuit breakers are to strong, they will

destroy the electrical system – danger

of fire.

Always cover positive terminal with the

specified cover or terminal cap.

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

Explanation of

Warning Signs

Before any cleaning,

maintenance, and re-

pair work switch off the

engine and pull spark

plug connector.

With the engine run-

ning, keep at a safe

distance from hoeing

or cutting tools.

Do not work without

guards in place. Be-

fore starting the en-

gine, bring guards in

proper position.

With the engine run-

ning, keep at a safe

distance from knife.

Do not touch moving

machinery parts. Wait

until they have come

to a complete stop.

With the engine run-

ning, keep at a safe

distance.

Only drive the attach-

ment at speed “I”.

Signs

When working with the

machine,wear individual protec-

tive ear plugs.

Wear protective gloves.

Wear solid shoes.

agria Multi-Purpose Machine 400P 13

2. Specifications

2

1

Dimensions:

a ........................................ 100 mm

b ........................................ 630 mm

c......................................... 160 mm

d ........................................ 380 mm

e ........................................ 700 mm

h .............................. 860–1080 mm

l........................................ 1200 mm

A .............. (13x5.00 - 6) 525 mm

A ..................... (3.50 - 6) 440 mm

A (Twin tyres 3.50 - 6) ..... 857 mm

A ..................... (4.00 - 8) 640 mm

A Hoeing tools........... 450–650 mm

Clutch: .............................V-belt clutch

with idler pulleys

between engine and gearbox

Friction clutch for reverse speed

Only use original agria V-belts!

(List of wear parts p49)

Transmission:...................Worm gear

with free-wheel drive mechanism on

drive wheels

Transmission oil SAE 90-API GL5

Filling quantity approx. 0.5 l

Speeds: ...................3 forward speeds

(moving V-belt to another pulley)

1 reverse speed (friction wheel)

see table below

Steering handle:...vibration damping,

height-adjustable,

side-adjustable without tools

Weight: ......................... Approx. 50 kg

Noise level:

Noise level ....................... L

p

= 84 dBA

in accordance with EN 11201 (at

operator’s ear)

Acoustic power level L

WA

= 96,1 dB(A)

in accordance with EN ISO 3744

Vibration acceleration value:

on handlebar:................ a

hw

< 2.5 m/s

2

in accordance with ISO 5349 at 85% of rated

engine speed with tool at work.

Speed Revolutions [rpm] Ground speed [km/h]

Wheel shaft

Pto Tyres

i

tot

n

dw

n

pto

13x5.00-6 3.50-6 4.00-8

I 67.5 55 1650 3.2 3.6 4.4

II 42.7 85 2550 5.0 5.6 6.9

III 28.1 125 3750 7.3 8.3 10.1

R 61.7 58 1740 3.4 3.8 4.7

Tyres: (Accessory) .............................

................ 13x5.00-6 (Grassland tyre)

....... 3.50 - 6 und 4.00 - 8 (Field tyre)

Tyre pressure: ........................ 1.0 bar

Multi-purpose machine

14

agria Multi-Purpose Machine 400P

2. Specifications

2

Engine

Manufacturer: ..........................Honda

Engine type: .............. GX 200 QHQ4

Version:....................... Fan-air cooled

1-cylinder, 4-stroke

petrol ohv engine

Bore:........................................ 68 mm

Stroke:..................................... 54 mm

Cubic capacity: ................... 196 ccm

Compression ratio:................. 8.5 : 1

Output: .................................... 4.8 kW

at 3,600 rpm

Max. torque:..........................13.2 Nm

at 3,000 rpm

Spark plug: ................NGK BPR6 ES

Spark plug gap: ............... 0.7–0.8 mm

Ignition system:

Contactless solenoid ignition, ignition

point is pre-set, radio remote

screened according to VDE 0879

Valve lash (engine cold):

Intake: ................ 0.15 mm ± 0.02 mm

Outlet: ................ 0.20 mm ± 0.02 mm

Starter:

Soft-pull recoil starter with mechanical

decompression facility

Fuel tank capacity: .................... 3.6 l

Fuel: Standard regular grade petrol for

motor vehicles, octane number see

engine operating instructions

Air filter: ..................Dry element filter

with foamed preliminary filter

Carburetor: .......... Throttle valve type

Mixture control screw:

opened approx. 2 1/8 turns in base

setting

Rated speed: .....................3,600 rpm

Top no-load speed:...........3,850 rpm

Idling speed:...........1,250–1,600 rpm

Engine oil:

Filling quantity..................approx. 0.6 l

Multi-grade oil SAE 10 W-40

SJ or higher quality grade

Operability on Slopes:

Continuous operation possible

up to ..................20° inclination (37 %)

Temporary operation possible

up to ..................25° inclination (47 %)

(with oil level at “max” = upper level

mark)

agria Multi-Purpose Machine 400P 15

3. Devices and Operating Elements

3

The agria multi-purpose machine type

400 is a base power machine and is al-

ways operated with an attachment

mounted. Therefore, the machine is

suited for horticultural, agricultural,

forestal operations, as well as for grass-

land and park maintenance and for win-

ter service work.

Available attachments are:

l

hoeing and tilling

l

mowing

l

turf and grounds care

l

ploughing

l

sweeping

l

gravel and salt spreading

l

snow dozing and rotory snow

cleaning

l

transporting

Engine

The four-stroke petrol engine runs on

conventional petrol (refer to fuel recom-

mendations p6). During the first 20 op-

erating hours (break-in period) do not

use engine to maximum power. Even

after the break-in period never use

engine at higher speed than necessary

for the work in hand.

I

High engine speed is harm-

ful to any engine and consid-

erably affects its longevity. This ap-

plies especially for no load operation.

Any overspeed (have the engine roar)

can result in immediate damage.

Cooling System

The engine is fan-cooled. Therefore

keep screen at recoil starter and cool-

ing fins of the cylinder clean and free

from sucked-in plant trash.

Idling Speed

Always ensure that idling speed is ad-

justed correctly. At low speeds and with

the speed control lever set to idle, the

engine is supposed to run smoothly and

without run-out.

Air Filter

The air filter purifies the air intake. A

blocked filter reduces engine output.

Ignition System

The engine is equipped with a mainte-

nance-free, contactless electronic igni-

tion system.

We recommend to have necessary

check-ups done by an expert only.

16 agria Multi-Purpose Machine 400P

3. Devices and Operating Elements

3

Speed Control Lever

The speed control lever (C/9) on the steering han-

dle is for stepless setting of engine speed from min.

= idle to max. = full throttle.

Safety circuit

The multi-purpose machine is equipped with a safety

circuit lever.



Stop position: When releasing the lever (C/4)

the ignition system is switched off (engine is shut

off). Beware – engine keeps running due to cen-

trifugal mass.



Start position: For starting the engine and

for short breaks, pull the clutch lever (C/5) and lock

with pawl (C/6).



Operating position: To operate the machine,

press down the safety circuit lever (E/3 or G/3).

W

Do not tie down the safety circuit lever.

I

The safety circuit lever also serves as engine

safety circuit in an emergency. Upon release,

the lever will automatically go to STOP position.

Choke

The choke lever (B/5) is on the carburetor.

 Close the choke for cold starts. To do this, move

the lever to the left.

 Open the choke for warm starts and operation.

To do this, move the lever to the right.











agria Multi-Purpose Machine 400P 17

3. Devices and Operating Elements

3

Fuel tap

The fuel tap (B/13) is on the carburetor.

 Move the tap to the right to open it.

 Move the tap to the left to close it.

Clutch

The multi-purpose machine is equipped with a V-

belt clutch with integrated reverse shift. Operation

is via the clutch lever (C/5).

The machine is decoupled when you pull the clutch

lever until pawl locks into place. Now, the engine

stops driving the machine. The clutch lever can be

locked with pawl (C/6) when the machine is

decoupled.

To avoid clutch slipping away during operation, a

clutch play is factory-set at the clutch lever (refer to

“Maintenance”).

After the first operating hour, the clutch play has to

be checked and, if necessary, re-adjusted (refer to

“Maintenance”).





B/13

C/5

C/6

18 agria Multi-Purpose Machine 400P

3. Devices and Operating Elements

3

Travelling Drive

Forward – Reverse

The multi-purpose machine is equipped with a

clutch-integrated FR-gearshift, which is operated

with the clutch lever (E/4 or G/4).

 Travelling drive forward speed:

Move clutch lever down (C/5) – the pawl is unlocked.

 Travelling drive idling speed:

Clutch lever (C/5) is pulled approx. half way – the

pawl is locked.

 Travelling drive reverse speed:

Pull clutch lever (C/5) all the way up.

Pawl (C/6) is for locking the clutch lever in idling

position (“0”).

On slopes, always turn machine towards the slope.

I

Note: Always park machine with clutch lever pulled (“0” – pawl

locked), otherwise clutch problems may arise due to deformation of V-belt.

Speeds

To change speeds, move the V-belt to another idler pulley (D/12) - see fold-out

page 54.

W

Before you move the V-belt, stop the engine and remove

the spark plug connector.

l

Remove nut (D/10) to remove the belt guard (D/8) and the belt guide plate (D/7).

l

Lock the clutch lever (D/4) in neutral position. This ensures that the idler

pulley (D/1) does not to press against theV-belt.

l

Move the V-belt (D/12) to the desired pulley (only use your hands, do not use

pointed or sharp tools. Otherwise the V-belt will be damaged).

l

Replace V-belt guide plate (D/7). Push the guard (D/7) onto pins (D/4) and

close it.

l

Fit nut (D/10) with spring washer (D/9) and tighten.

Only drive pto-driven attachments at speed “I”.













agria Multi-Purpose Machine 400P 19

3. Devices and Operating Elements

3

Figure: V-belt is in “speed I” position.

On the V-belt guard to the left there is a

small window to monitor the current

speed, i.e. on which pulley the belt is

currently running.

Recommended speeds

Wheel drive

The multi-purpose machine is equipped

with drive-wheel engagement and a

wheel drive. This can be engaged/dis-

engaged via a selector sleeve and from

the handlebar.

Wheel drive engaged:

Move wheel drive lever (C/11) down to

unlock the pawl.

Wheel drive disengaged:

Move wheel drive lever (C/11) up to lock

the pawl.

With the engine running, the wheel drive

is engaged the following way:

l

Pull the clutch lever (C/5) to middle

position (neutral) and hold.

l

Unlock pawl (C/10).

l

Move hand lever for wheel drive

(C/11) down.

l

Slowly release the clutch lever (C/5)

while pressing the throttle.

In case wheel drive cannot be engaged,

couple and decouple. Then engage

wheel drive.

I Pto-driven

attach-

ments

C/11

C/10

Rotary snow

cleaner, mowing,

sweeping,

spreading,

shredding, spray-

ing, ploughing

II Surface work

not pto-driven

Snow dozing,

transport work

III Rotary

cultivation

Hoeing, ridging

20 agria Multi-Purpose Machine 400P

3. Devices and Operating Elements

J

1

1 Detent spring

3

Drive-Wheels

W

Only mount and dismount

drive-wheels with engine

turned off.

The drive-wheels are equipped with a

detent spring (1) and can be mounted

and adjusted without tools.

The detent spring engages into a ring

groove on the wheel-shaft to hold the

drive-wheel.

On each side of the wheel-shaft there

are 2 ring grooves respectively. With

detent spring engaging into outer ring

groove, the drive-wheel turns in neutral

on wheel-shaft. With detent spring en-

gaging into inner ring groove, the drive-

wheel engages with a toothed wheel on

the wheel-shaft to be driven by the

same.

Mounting drive-wheels

I

For full tractive power, mount

field tyres with the tread profile

pointing in travel direction (seen from

above).

l

Lift detent spring (1) slightly and

place into assembly position (fig. J)

(front ring groove on hub).

l

Mount drive-wheels onto wheel-

shaft, with the side for the detent spring

pointing outwards.

l

Let detent spring engage in a ring

groove again (fig. K and L).

l

Brush Bio-lubricating grease onto

both ends of wheel-shaft (small diam-

eter of wheel-shaft).

For dismounting drive-wheels, proceed

accordingly but in reverse order.

La pagina sta caricando ...

Agria 0400 Manuale del proprietario

Agria 0400 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti