ProLights LED Fresnel Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente
USER MANUAL
MANUALE UTENTE
ECLFR2KTU-DY
EN - IT
FRESNEL PROJECTOR
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
REV.01-05/19
1
ECLFR2KTU-DY
Packing content
ECLFR2KTU-DY
ECLFR2KTPG
ECLFR2KBD
ECLFRSPG
Power cable
User manual
TABLE OF CONTENTS
Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description and specifications
1. 2 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 DMX addressing
3. 5 DMX configuration
3. 6 Linking
3. 7 Screen
3. 8 Fixture settings
3. 9 Information
3. 10 Master/Slave mode
3. 11 Effects mode
3. 12 Static mode
3. 13 DMX control
3. 14 Connection of the DMX line
3. 15 Construction of the DMX termination
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Trouble shooting
2
2
3
5
6
7
7
8
9
9
9
10
10
11
11
11
11
12
13
13
14
14
ECLFR2KTU-DY
2
SAFETY
General instruction
The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modifications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
The connection to the main network of electric distribution must be carried out by a qualified electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
This unit is not for home use, only professional applications.
Never use the fixture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 45 °C.
Make certain that no inflammable liquids, water or metal objects enter the fixture.
Do not dismantle or modify the fixture.
All work must always be carried out by qualified technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
If the unit is to be put out of operation definitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
If this device will be operated in any way different to the one described in this manual, it may suffer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
Before starting any maintenance work or cleaning the projector, cut off power from the main supply.
Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
Install the fixture in a well ventilated place.
Keep any inflammable material at a safe distance from the fixture.
Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their effectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally deformed.
Never look directly at the light beam. Please note that fast changes in lighting, e. g. flashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
Do not touch the product’s housing when operating because it may be very hot.
This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
We decline any liability deriving from improper use of the product.
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
3
ECLFR2KTU-DY
- 1 - INTRODUCTION
1.1 DESCRIPTION
ECLFR2K is the LED replacement for a standard tungsten 2K fresnel. Featuring the output characteristics
of a traditional Fresnel but with beam control, functional barn doors and a power source that focuses on
outstanding colour rendition. The ECLFR2K adds all the advantages of LED to the Fresnel.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
Source: 507W high-power white LED
CT: (TU) 3200 K - (DY) 5600K
CRI: (TU) 97 Ra - (DY) 92
R9: (TU) >90 - (DY) > 81
Luminous flux: (TU) (45°) 25338 lm (15°) 22556 lm - (DY) (45°) 33750 lm (15°) 27960lm @Full
Lux: (TU) (15°) 28400 lux - (45°) 6150 lux - (DY) (15°) 31200 lux - (45°) 6790lux @3m full
Lux: (TU) - (15°) 10224 lux - (45°) 2214 lux - (DY) (15°) 11231 lux - (45°) 2445lux @5m full
Source life expectancy: >50.000 h
Other: TM30-15RG/RF: (TU - 15°) 94/103, (TU - 45°) 93/104 - (DY - 15°) 90/102, (DY - 45°) 90/103 - TLCI:
(TU - 15°) 94.8, (TU - 45°) 94.4 - (DY - 15°) 94, (DY - 45°) 93.6
OPTICS
Zoom: 15° - 45° manual
Lens diameter: 250mm
Lens type: Fresnel zoom lens
Other: Spigot, barn door and gel frame included
COLOUR SYSTEM
Colour mixing: warm white
Macros: several pre-build macros with adjustable speed
DYNAMIC EFFECTS
Static colour mode: selection of static dimmer
Manual colour mode: manual adjust of dimmer throught menu and knob
Auto mode: built-in programs with execution speed adjustment
BODY
Hardware on-board: filter frame, 8 doors barndoor, omega bracket spigot
Body: sturdy die-cast aluminium body conceived for long-time durability
Body colour: black
Other: Pan/Tilt infinite for pole operated version
CONTROL
Protocols: DMX512, RDM, Local knob
DMX channels: 1 / 2-1 / 2-2 / 3 / 5channel
RDM: RDM ready for fixture remote monitor and settings
Display: black OLED high resolution display
Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included
Master/Slave: for synchronized operation of more units linked in a chain
ECLFR2KTU-DY
4
Other: 16bit control of dimmer
ELECTRONICS
Dimmer: linear 0~100% electronic dimmer
Dimmer curves: different dimming curves available
Strobe / shutter: 1 - 30 Hz, electronic
Operating temperature: -10° ~ +45°
Flicker: flicker free frequency with adjustable PWM
Selectable PWM: 600~25K Hz
ELECTRICAL
Power consumption: 550W
Power supply: 100-240V – 50/60Hz
Power consumption (at 230V): 466W
Power consumption (at 120V): 469W
Output (at 230V): 4 units on a single power line
Output (at 120V): 2 units on a single power line
Power factor: pF 0.96 @ 230V - pF 0.99 @ 120V
PHYSICAL
Cooling: combination of heat pipe cooling system and low noise fan
Sospension and fixing: hanging bracket suitable for safe hanging and positioning
Signal connection: Amphenol XLR 5p IN/OUT connectors
Power connection: Neutrik powerCON TRUE1 IN/OUT connectors
IP rating: 20
Dimensions (WxHxD): 421x537x455mm
Weight: 17.2kg
Technical drawing Fig.1
455
421
537
3
4
5
98
12
13
14
10
15
11
2
1
6
7
Fig.2
5
ECLFR2KTU-DY
1.3 OPERATING ELEMENTS AND CONNECTIONS
1. VENTILATION GRID for air flow outlet not to
be obstructed.
2. Knob for inclination adjustment.
3. HANDLE
4. MOUNTING BRACKET
5. SPIGOT
6. CONTROL PANEL with display and 1 button
used to access the control panel functions
and manage them.
7. ZOOM ADJUSTMENT Knob AND FOCUS to
zoom the projected image clearly.
8. GEL FILTER FRAME
9. BARN DOOR with directional flaps to adjust
the light beam.
10. GUIDE for locking and releasing accessories
11. MAIN FUSE HOLDER: replace a burnt-out fuse by
one of the same type only
12. POWER IN (PowerCON TRUE IN): for connection
to a socket (100-240V~/50-60Hz) via the supplied
mains cable.
13. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3 =
DMX+, 4 N/C, 5 N/C.
14. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-, 3 =
DMX+, 4 N/C, 5 N/C.
15. POWER OUT (PowerCON TRUE OUT): power
output for connection of multiple units in series.
Fig.4
CLAMP
ECLFR2KTU-DY
6
- 2 - INSTALLATION
2.1 MOUNTING
ECLFR2KTU-DY is designed for applications in exhibition areas, commercial spaces, museums, restaurant,
churches, and any other installation where size is an important factor. For fixing, stable mounting clips are
required. The mounting place must be of sufficient stability and be able to support a weight of 10 times
of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
garding safety) currently in force in the country in which the fixtures being used.
Install the projector at a suitable location.
Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-
ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm. The
adjust the projector and use the knobs.
NOTE - For the installation of the ECLFR2KTU-DY make sure that the ridge of the adaptor is in with the
groove of the track. Turn knobs 90° to connect the adaptor to the circuit. Please see the figure 4.
Fig.5
7
ECLFR2KTU-DY
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
To turn ECLFR2KTU-DY connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit
is ready for operation and can be operated via a DMX controller. To switch off, disconnect the mains plug
from the socket. For a more convenient operation it is recommended to connect the unit to a socket which
can be switched on and off via a light switch.
3.2 BASIC
The ECLFR2KTU-DY has a display and 1 button for access to the control panel functions (fig.5).
Knob
Used to access the menu, to return a previous
menu option, to navigate through the menu,
to select and store the current menu or confirm
the current function value or option within a
menu
MENU
1 CONNECT
ð
DMX Address
ð
Value (001-512)
DMX Mode
ð
EASY 1CH
BASIC 2CH 1
BASIC 2CH 2
BASIC 3CH
STANDARD 5CH
2 SETUP
ð
Screen
ð
Back Light
ð
On
10S
20S
30S
Flip Display
ð
No-Yes
3 ADVANCED
ð
Dimmer Mode
ð
Off
Dimmer 1
Dimmer 2
Dimmer 3
Led Frequency
ð
600Hz
1200 Hz
2000 Hz
4000 Hz
6000Hz
25kHZ
Fan Mode
ð
Auto
On
Off
Silent
Factory Reload
ð
No-Yes
4 INFORMATION
ð
Fixture Hours
ð
0-9999
Version
ð
V1.0
UID
ð
15D0022A****
5 STAND ALONE
ð
Master/Slave
ð
Master/Slave
Effects
ð
Effect 1
ð
Speed 1~100
Effect 2
Effect 3
Effect 4
Static
ð
Dimmer
ð
Value ( 0~255)
Strobe
ECLFR2KTU-DY
8
3.3 MENU STRUCTURE
9
ECLFR2KTU-DY
3.4 DMX ADDRESSING
To set DMX addressing follow the instructions below:
Press the knob to enter the menu mode.
Use the knob to select Connect. Press the knob to confirm.
Rotate the knob to select DMX Address. Press the knob to confirm.
Rotate the knob to select the desired value 001-512. Press the knob to confirm.
Press repeatedly the knob to return the menu mode.
To able to operate the ECLFR2KTU-DY with a light controller, adjust the DMX start address for the first a
DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX
channel, adjust the start address 33 on the ECLFR2KTU-DY. The other functions of the light effect panel are
then automatically assigned to the following addresses.
3.5 DMX CONFIGURATION
The ECLFR2KTU-DY has different DMX channels configurations available selectable through the control
panel.
Rotate the knob to enter the menu mode.
Use the knob to select the Connect. Press the knob to confirm.
Press the knob to select the DMX mode. Then press the knob to confirm.
Press the knob to select the desired configuration (EASY 1CH - BASIC 2CH 1 - BASIC 2CH 2 - BASIC3CH - STANDARD
5CH); then press it to save.
Press repeatedly the knob to return the menu mode.
The tables on page 12 indicate the operating mode and DMX value. The ECLFR2KTU-DY is equipped with
5-pole XLR connections.
3.6 LINKING
Several units may be interconnected; follow the instructions below:
1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the first slave unit.
2. Connect the DMX OUT of the first slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last fixture (see page 13).
Numero
canali DMX
Indirizzo di
start (esempio)
Indirizzo DMX
occupati
Prossimo indirizzo di start
possibile per unità n°1
Prossimo indirizzo di start
possibile per unità n°2
Prossimo indirizzo di start
possibile per unità n°3
1 33 33 34 35 36
2 33 33-34 35 37 39
3 33 33-35 36 39 42
5 33 33 - 37 38 43 48
. . . . . . . . . . . .
DMX Address: 33 DMX Address: 42DMX Address: 36 DMX Address: 39
Fig.5 - Example 3 DMX channels configuration
. . . . . . . . . . . .
DMX512 Controller
ECLFR2KTU-DY
10
3.7 SCREEN
It is possible to modify the following parameters, related to the display, following the same procedure:
Press the knob to access the main menu.
Rotate the knob to scroll through the menu, select Set Up, then press the knob access the next menu.
Press the knob to select Screen and press the knob to proceed.
Select the proposed option with the knob and press the knob to confirm.
- Backlight - Auto Off display backlight. This function allows you to switch off automatically the back-
lighting of the display after a certain time which can be set using the directional keys. To have the
display always on select On or set a value between those shown (10s, 20s, 30s) to turn off the display
once the chosen time has elapsed, after exiting the menu.
- Flip Display - Display orientation. This feature allows you to rotate the display by 180 ° to get a better
view of the display when the unit is hanging upside down. Select Yes to activate the function, No to
deactivate it.
Press the knob to confirm the selection.
Press the knob repeatedly to exit the menu and to save the changes made.
3.8 ADVANCED
You can change the parameters for the device by following these steps:
Press the knob to enter the menu mode.
Use the knob to select the Advanced. Press the button knob.
Press the knob to select the desired option and press the Knob to confirm:
- Dimmer Mode - Adjusting the dimmer. Enter in Dimmer Mode to select specific dimming curve.
Particularly when set:
Off: The increase in light intensity is linear.
Dimmer 1: dimmer curve with low fade.
Dimmer 2: dimmer curve with medium fade.
Dimmer 3: dimmer curve with high fade.
- LED Frequency - To adjust the frequency of the LEDs. Select the frequency 600 Hz - 25 KHz using the knob
and press it to confirm the selection.
11
ECLFR2KTU-DY
- Fan Mode - Fan Speed. Select the fan speed (Auto, On, Off, Silent) using the knob.
- Factory Reload - To reset the unit. Select Yes or No and select the knob to confirm.
Press repeatedly the knob to return the menu mode.
3.9 INFORMATION
To view all the information on the device, proceed as follows:
Press the knob to access the main menu. Rotate the knob to select Information, then press it to access
the next menu.
Rotate the knob to scroll through the menu, then select one of the following informationa nd press it
to display it.
- Fixture Time - To view the operating time of the projector.
- Software Version - To view the firmware version will show on the display.
- UID - To view the identification ID for the RDM control.
Press repeatedly the knob to return the menu mode.
3.10 MASTER/SLAVE MODE
This mode will allow you to link up the units together without a controller. Choose a unit to function as the
Master. The unit must be the first unit in line; other units will work as slave.
Press the knob so many times until the display shows Stand Alone, then press it.
Select Master/Slave.
Using knob, select the desired mode and then press the Knob.
Press the knob to go back or to meet the waiting time to exit the setup menu.
Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the
units. For longer cable runs we suggest a terminator at the last fixture (see page 13).
Set the slaves to the same DMX modes.
NOTE: the unit, set in Static or Effect mode, always appears to be Master.
3.11 EFFECTS MODE
This fixture has a built-in automatic program. To access this, please see the below instructions:
To enter the Effects mode, press the knob to access the menu.
Rotate the knob select Stand Alone, then select Effect. Press it to confirm
Use the knob to select the desired program Effect 1, Effect 2, Effect 3, Effect 4, then press it to confirm.
Set the value (1 - 100), then press the knob to confirm.
NOTE: after selecting the described mode, the unit will be Master.
3.12 STATIC MODE
This fixture has the ability to accept custom static color settings. Access these chases via the control panel
on the back of the fixture.
To enable the static mode, press the knob repeatedly until Stand Alone shows on the display.
Set the strobo value Strobe (000 - 255), through the knob, then press it to confirm.
Set the dimmer value Dimmer (000 - 255), through the knob, then press it to confirm.
Press repeatedly the knob to return the menu mode.
NOTE: after selecting the described mode, the unit will be Master.
1 CHANNEL
MODE
FUNCTION DMX
Value
1 Ch
1
DIMMER
0~100% 000 - 255
2 CHANNELS 2
MODE
FUNCTION DMX
Value
2 Ch
1
DIMMER
0~100% 000 - 255
2
STROBE
NO Function
Strobe Slow to Fast
000 - 010
011 - 255
3 CHANNELS
MODE
FUNCTION DMX
Value
3 Ch
1
DIMMER
0~100% 000 - 255
2
DIMMER FINE
0~100% 000 - 255
3
STROBE
NO Function
Strobe Slow to Fast
000 - 010
011 - 255
5 CHANNELS
MODE
FUNCTION DMX
Value
5 Ch
1
DIMMER
0~100% 000 - 255
2
STROBE
NO Function
Strobe Slow to Fast
000 - 010
011 - 255
3
AUTO PROGRAMS
No Function
Auto Program 1
Auto Program 2
Auto Program 3
Auto Program 4
000 - 010
011 - 070
071 - 130
131 - 190
191 - 255
4
AUTO SPEED
Auto speed slow to fast 000 - 255
5
DIMMER SPEED MODE
Preset dimmer speed from display menu
Dimmer speed mode off
Dimmer speed mode1 (fast speed)
Dimmer speed mode2 (middle speed)
Dimmer speed mode3 (slow speed)
000 - 051
052 - 101
102 - 152
153 - 203
204 - 255
2 CHANNELS 1
MODE
FUNCTION DMX
Value
2 Ch
1
DIMMER
0~100% 000 - 255
2
DIMMER FINE
0~100% 000 - 255
ECLFR2KTU-DY
12
3.13 DMX CONTROL
13
ECLFR2KTU-DY
Fig.6
Fig.7
3.14 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the systems earth, as this would
cause faulty fixture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplifier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
Connect the controller DMX input to the DMX output of the first unit.
Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.15 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reflected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in figure.
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
Example:
5 pin XLR connector
4
ECLFR2KTU-DY
14
- 4 - MAINTENANCE
4.1 MAINTENANCE AND CLEANING THE UNIT
Make sure the area below the installation place is free from unwanted persons during setup.
Switch off the unit, unplug the main cable and wait until the unit has cooled down.
All screws used for installing the device and any of its parts should be tightly fastened and should not
be corroded.
Housings, fixations and installation spots (ceiling, trusses, suspensions) should be totally free from any
deformation.
The main cables must be in impeccable condition and should be replaced immediately even when a
small problem is detected.
It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or
other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the
main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe
the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might
penetrate the unit and cause damage to it.
4.2 TROUBLESHOOTING
Problems Possible causes Checks and remedies
Fixture does not light up
No mains supply
Dimmer fader set to 0
Faulty LED
Check the power supply voltage
Increase the value of the dimmer channels
Replace the LED board
General low light intensity
Dirty lens assembly
Misaligned lens assembly
Clean the fixture regularly
Install lens assembly properly
Fixture does not power up
No power
Loose or damaged power cord
Check for power on power outlet
Check power cord
Contact an authorized service center in case of technical problems or not reported in the table can not be
resolved by the procedure given in the table.
REV.01-05/19
Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.
La riproduzione - anche parziale - per propri scopi commerciali è vietata.
Al fine di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modificare, in
qualunque momento e senza preavviso, le specifiche menzionate nel presente manuale di istruzioni.
Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it
3
ECLFR2KTU-DY
ECLFR2KTU-DY
ECLFR2KTPG
ECLFR2KBD
ECLFRSPG
Cavo di alimentazione
Manuale utente
Contenuto dell'imballo:
INDICE
Sicurezza
Avvertenze generali
Attenzioni e precauzioni per l’installazione
1 Introduzione
1. 1 Descrizione e specifiche tecniche
1. 2 Elementi di comando e di collegamento
2 Installazione
2. 1 Montaggio
3 Funzioni e impostazioni
3. 1 Funzionamento
3. 2 Impostazione base
3. 3 Struttura menù
3. 4 Modalità DMX
3. 5 Configurazione canali DMX
3. 6 Collegamento
3. 7 Screen
3. 8 Advanced
3. 9 Informazioni sul dispositivo
3. 10 Modalità Master/Slave
3. 11 Modalità Effects
3. 12 Modalità Static
3. 13 Canali DMX
3. 14 Collegamenti della linea DMX
3. 15 Costruzione del terminatore DMX
4 Manutenzione
4. 1 Manutenzione e pulizia del sistema ottico
4. 2 Risoluzione dei problemi
4
4
5
7
8
9
9
10
11
11
11
12
12
13
13
13
13
14
15
15
16
16
ECLFR2KTU-DY
4
ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione
questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni
importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.
SICUREZZA
Avvertenze generali
I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-
tanto recano la sigla .
Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di
fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.
È obbligatorio effettuare il collegamento ad un impianto di alimentazione dotato di unefficiente messa
a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le
linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di
interruttori differenziali opportunamente dimensionati.
Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere effettuate
da un installatore elettrico qualificato. Verificare che frequenza e tensione della rete corrispondono alla
frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.
L’unità non per uso domestico, solo per uso professionale.
Evitare di utilizzare l’unità:
- in luoghi soggetti a vibrazioni, o a possibili urti;
- in luoghi a temperatura superiore ai 45°C.
Evitare che nell’unità penetrino liquidi infiammabili, acqua o oggetti metallici.
Non smontare e non apportare modifiche all’unità.
Tutti gli interventi devono essere sempre e solo effettuati da personale tecnico qualificato. Rivolgersi al
più vicino centro di assistenza tecnica autorizzato.
Se si desidera eliminare il dispositivo definitivamente, consegnarlo
per lo smaltimento ad un’istituzione locale per il riciclaggio.
Attenzioni e precauzioni per l’installazione
Se il dispositivo dovesse trovarsi ad operare in condizioni differenti da quelle descritte nel presente
manuale, potrebbero verificarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra
operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.
Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete
di alimentazione.
È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-
siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel
paese di utilizzo.
Installare l’unità in un luogo ben ventilato.
Mantenere i materiali infiammabili ad una distanza di sicurezza dall’unità.
I filtri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro efficienza.
I LED devono essere sostituiti se danneggiati o termicamente deformati.
Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-
vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.
Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.
This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
We decline any liability deriving from improper use of the product.
1 / 1

ProLights LED Fresnel Manuale utente

Categoria
Stroboscopi
Tipo
Manuale utente

in altre lingue