AJA IPR-10G-HDMI Manuale utente

10 GigE IP Mini-Converters

SMPTE 2110 IP Transmit/Receive

Version 2.1r1

Published December 2, 2019

Installation and Operation Guide

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered

trademarks of AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,

V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

Copyright

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web

https://www.aja.com

Support Email

suppor[email protected]

Sales Email

[email protected]

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

10 GigE IP Mini-Converters Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IPT-10G2-SDI Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IPT-10G2-HDMI Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IPR-10G2-SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

IPR-10G2-HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

IPR-10G-HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Simplied Block Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Control LAN, Ready, Link/Act, and Lock LED Behavior. . . . . . . . . . . . . . 11

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Initial Setup By Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Initial Setup By AJA eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Settings Retained. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

REST API Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 2 – eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Acquiring eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

eMini-Setup Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Installing eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PC Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mac Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Running eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

PC Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Mac Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operating eMini-Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Control LAN Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Media Network 1 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Media Network 2 Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Update Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Firmware Update Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 3 – 10 GigE IP Mini-Converters Web Interface. . . . . . . .23

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Networking Option – Using Only the Media LAN Port for Control and Media

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Web Browser via Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

General Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

IPT-10G2-SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

IPR-10G2-HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Cong Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

IPT-10G2-SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

IPR-10G2-HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Presets Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Presets Screen Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Network Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Contents

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 4 www.aja.com

Firmware Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Downloading and Installing Updated Firmware . . . . . . . . . . . . . . . . . 44

Booting the 10 GigE IP Mini-Converters from the Safeboot Firmware . . . 45

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 47

IPT-10G2-SDI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

IPT-10G2-HDMI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

IPR-10G2-HDMI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

IPR-10G2-SDI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

IPR-10G-HDMI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 56

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . .64

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . . 64

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 5 www.aja.com

Chapter 1 – Introduction

Overview

AJA 10 GigE IP Mini-Converters are designed for point of use applications for

encoding, transport, reception and decoding of IP based video sources. Rugged,

compact and fanless, the 10 GigE IP Mini-Converters provide the bridge between

Baseband and IP video for a range of applications, such as sending and receiving

video over IP from remote facilities in post production, source monitoring, digital

signage, and video walls. 10 GigE IP Mini-Converters ease the cost of extensive

monitoring distribution in a facility.

The 10 GigE IP Mini-Converter Transmitters take baseband HDMI or SDI input

and encode the data as SMPTE 2110. The embedded audio associated with the

video stream is also encoded to SMPTE 2110. Alternatively, analog audio can be

encoded and sent with the video stream instead.

The 10 GigE IP Mini-Converter Receivers decode SMPTE 2110 and format the data

for either HDMI or SDI output. The audio associated with the video stream is

extracted, synchronized, and then embedded into the HDMI or SDI signal as well

as output on a stereo analog RCA audio output.

UltraHD p30 can be received only by the IPR-10G-HDMI.

Both the IPR-10G2-HDMI and the IPR-10G-HDMI can provide RGB (rather than

YCbCr) to a compatible monitor if the monitor or other sink device indicates this

availability via EDID.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 6 www.aja.com

10 GigE IP Mini-Converters Features

IPT-10G2-SDI Features

• SMPTE ST 2110 audio, video transmitter

• Rugged, fanless design

• 2x 10 GigE SFP+ cages for media LAN (providing support for hitless switching)

with status light

• 1x 1 GigE RJ45 socket for control LAN (with status light)

• 1x 3G-SDI Input

• 1x 3G-SDI Loop Out

• Support for HD up to 1080 60p, YCbCr4:2:2

• Full 10-bit pixel processing pipeline

• Embedded SDI audio input (up to eight channels)

• 2x RCA analog audio input

• 1x BNC Reference Out

• 1x mini-USB port for initial network configuration with AJA eMini-Setup

software

• Complete control interface on any web browser from a built-in web server

• Customizable control with AJA REST API

• 5-year international warranty and support

IPT-10G2-HDMI Features

• SMPTE 2110 audio, video transmitter

• Rugged, fanless design

• 2x 10 GigE SFP+ cages for media LAN (providing support for hitless switching)

with status light

• 1x 1 GigE RJ45 socket for control LAN with status light

• Dedicated HDMI transmitter with full size HDMI 1.4b video input port

• Support for HD up to 1080 60p, YCbCr 4:2:2

• Full 10-bit pixel processing pipeline

• Embedded HDMI audio input (up to eight channels)

• 2x RCA analog audio input

• 1x BNC Reference Out

• 1x mini-USB port for initial network configuration with AJA eMini-Setup

software

• Complete control interface on any web browser from a built-in web server

• Customizable control with AJA REST API

• 5-year international warranty and support

IPR-10G2-SDI

• SMPTE ST 2110 audio, video receiver

• Rugged, fanless design

• 2x 10 GigESFP+ cages for media LAN (providing support for hitless switching)

with status light

• 1x 1 GigERJ45 socket for control LAN (with status light)

• 2x 3G-SDI Output

• Support for HD up to 1080 60p, YCbCr4:2:2

• Full 10-bit pixel processing pipeline

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 7 www.aja.com

• Embedded SDI audio output (up to eight channels)

• 2x RCA analog audio output

• 1x BNC Reference (reserved for future potential features)

• 1x mini-USB port for initial network configuration with AJA eMini-Setup

software

• Complete control interface on any web browser from a built-in web server

• Customizable control with AJA REST API

• 5-year international warranty and support

IPR-10G2-HDMI

• SMPTE 2110 audio, video receiver

• Rugged, fanless design

• 2x 10 GigE SFP+ cages for media LAN (providing support for hitless switching)

with status light

• 1x 1 GigE RJ45 socket for control LAN with status light

• Dedicated HDMI transmitter with full size HDMI 1.4b video output port

• Support for HD up to 1080 60p, YCbCr 4:2:2

• Full 10-bit pixel processing pipeline

• Embedded HDMI audio output (up to eight channels)

• 2x RCA analog audio output

• 1x BNC Reference (reserved for future potential features)

• 1x mini-USB port for initial network configuration with AJA eMini-Setup

software

• Complete control interface on any web browser from a built-in web server

• Customizable control with AJA REST API

• 5-year international warranty and support

IPR-10G-HDMI

• SMPTE 2110 audio, video receiver

• Rugged, fanless design

• 1x SFP+ Cage for 10G Ethernet media, control, and timing input – SFP+

modules not included

• 1x RJ-45 (IEC 60603-7) for 10/100/1000 Base-T Ethernet for control

• Dedicated HDMI transmitter with full size HDMI 1.4b video output port

• Essence support: SMPTE 2110-10, 2110-20, 2110-30

• Support for receiving UltraHD p23.98, p24, p25, p29.97, p30

• Full 10-bit pixel processing pipeline

• Embedded and analog audio outputs

• Networked Media Open Specifications (NMOS) Support

• Ember Plus Support

• Network (LAN) control and status

• 1x mini-USB port for initial network configuration with AJA eMini-Setup

software

• Complete control interface on any web browser from a built-in web server

• Customizable control with AJA REST API

• 5-year international warranty and support

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 8 www.aja.com

Frequently Asked Questions

To access responses to freqently asked questions about the

10 GigE IP Mini-Converters, please use the following links:

• https://www.aja.com/products/ipt-10g2-sdi#support

• https://www.aja.com/products/ipt-10g2-hdmi#support

• https://www.aja.com/products/ipr-10g2-sdi#support

• https://www.aja.com/products/ipr-10g2-hdmi#support

• https://www.aja.com/products/ipr-10g-hdmi#support

System Requirements

Remote computer configuration and control is accomplished using the

10 GigE IP Mini-Converters' internal web server. A macOS X or Windows

computer with a web browser installed is all that is required. Additionally, initial

configuration using eMini-Setup will require a USB port between the host

computer and the 10 GigE IP Mini-Converter.

NOTE: Chrome and Firefox are the preferred web browsers for control on Windows.

Safari is the preferred web browser for control on macOS. Other web browsers

may work, but AJA cannot guarantee consistent operation for all web browsers or

web browser versions.

Simplified Block Diagrams

Figure 1. IPT-10G2-SDI/HDMI Simplified Block Diagram

Reference

Output

Video over IP

Processing

Video

Audio

2-Channel

RCA Analog

Audio Input

Control LAN

Media LAN 1

USB Port

(connect to PC or Mac)

For initial setup of

network interfaces

Media LAN 2

SDI Loop Through

SDI Input

HDMI Input

with Embedded

Audio

(IPT-10G2-SDI only)

(IPT-10G2-HDMI only)

IPT-10G2-SDI / IPT-10G2-HDMI

Video over IP

Transmitter

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 9 www.aja.com

Figure 2. IPR-10G2-SDI/HDMI Simplified Block Diagram

Video over IP

Processing

Audio

D/A

Video

Audio

HDMI

Transmitter

(IPR-10G2-HDMI

only)

2-Channel

RCA Analog Audio

Monitor Output

HDMI Output

with 8 Ch. of

Embedded Audio

Control LAN

Media LAN 1

USB Port

(connect to PC or Mac)

For initial setup of

network interfaces

Video over IP

Receiver

SDI Out 1 with 8 Ch.

of embedded audio

SDI Out 2 with 8 Ch.

of embedded audio

SDI

Transmitter

(IPR-10G2-SDI

only)

IPR-10G2-SDI / IPR-10G2-HDMI

Media LAN 2

Reference

Input

Not active. Reserved for

potential future feature(s).

Figure 3. IPR-10G-HDMI Simplified Block Diagram

Video over IP

Processing

Audio

D/A

Video

Audio

HDMI

Transmitter

2-Channel

RCA Analog Audio

Monitor Output

HDMI Output

with Embedded

Audio

1 GbE RJ45 socket

for Control LAN

SFP+ Cage for

10 GbE Media LAN

USB Port

(connect to PC or Mac)

For initial setup of

network interfaces

Video over IP

Receiver

IPR-10G-HDMI

I/O Connections

Figure 4. IPT-10G2-SDI Connections

2 Channel

Unbalanced

Analog Audio

Input

(RCA Jacks)

Input SDI

Connector 1

Control

LAN

SFP+ Cage for

10 Gbps Ethernet

Lock LED

Ready LED

Link/Act

LED 1

Link/Act

LED 2

SFP+ Cage for

10 Gbps Ethernet

Output SDI

Connector 2

USB Port

+5-16 VDC

Power Input

Reference

Out BNC

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 10 www.aja.com

Figure 5. IPT-10G2-HDMI Connections

2 Channel

Unbalanced

Analog Audio

Input

(RCA Jacks)

Input HDMI

Connector

USB Port

+5-16 VDC

Power Input

Control

LAN

SFP+ Cage for

10 Gbps Ethernet

Lock LED

Ready LED

Link/Act

LED 1

Link/Act

LED 2

SFP+ Cage for

10 Gbps Ethernet

Reference

Out BNC

Figure 6. IPR-10G2-SDI Connections

2 Channel

Unbalanced

Analog Audio

Output

(RCA Jacks)

Output SDI

Connector 1

Control

LAN

SFP+ Cage for

10 Gbps Ethernet

Lock LED

Ready LED

Link/Act

LED 1

Link/Act

LED 2

SFP+ Cage for

10 Gbps Ethernet

Output SDI

Connector 2

USB Port

+5-16 VDC

Power Input

Reference BNC.

Reserved for Future

Potential Features.

Figure 7. IPR-10G2-HDMI Connections

2 Channel

Unbalanced

Analog Audio

Output

(RCA Jacks)

Output HDMI

Connector

USB Port

+5-16 VDC

Power Input

Control

LAN

SFP+ Cage for

10 Gbps Ethernet

Lock LED

Ready LED

Link/Act

LED 1

Link/Act

LED 2

Reference BNC.

Reserved for Future

Potential Features.

SFP+ Cage for

10 Gbps Ethernet

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 11 www.aja.com

Figure 8. IPR-10G-HDMI Connections

2 Channel

Unbalanced

Analog Audio

Output

(RCA Jacks)

Output

HDMI

Connector

USB

Port

+5-20 VDC

Power

Input

Control

LAN

SFP+ Cage

for 10 Gbps

Ethernet

Lock LED

Ready LED

Link/Act

LED

Control LAN, Ready, Link/Act, and Lock LED Behavior

The Control LAN LED illuminates to indicate a link. Blinking indicates activity.

The Ready LED illuminates green when the unit has finished powering up and is

ready to use.

The Link/Act LED 1 and Link/Act LED 2 behavior is as follows:

• Off - No SFP+ module present

• Red - SFP+ module present, no link

• Green - Link is up

• Green flash - Link is up and there is Tx or Rx activity

The Lock LED behavior is as follows:

• Off - No Precision Time Protocol (PTP) is detected

• Red - A PTP error is detected

• Yellow and flashing - Locking Phase 1

• Yellow - Locking Phase 2

• Green and flashing - Locking Phase 3

• Green - Signal is locked

NOTE: Achieving locked status may take 5 or more minutes depending on network jitter

behavior. The output of the unit will still function during the locking period.

Installation Overview

Detailed instructions are provided in "Chapter 2 – eMini-Setup" on page 14 and

"Chapter 3 – 10 GigE IP Mini-Converters Web Interface" on page 23.

As an overview, however, there are two methods available for initial setup for

10 GigE IP Mini-Converters:

1. Using a web browser on the host computer connected to the same network

as the 10 GigE IP Mini-Converter, or

2. Using the AJA eMini-Setup application running on the host computer that is

directly connected to the 10 GigE IP Mini-Converter via USB.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 12 www.aja.com

Initial Setup By Web Browser

NOTE: Chrome and Firefox are the preferred web browsers for control on Windows.

Safari is the preferred web browser for control on macOS. Other web browsers

may work, but AJA cannot guarantee consistent operation for all web browsers or

web browser versions.

10 GigE IP Mini-Converters require a network connection for initial configuration,

control and firmware updates. 10 GigE IP Mini-Converters are shipped from the

factory with DHCP enabled, and support automatic network discovery via SSDP

and MDNS.

To Set Up the Unit with a Web Browser

1. Connect the 10 GigE IP Mini-Converter Control Port to the intended

network with an Ethernet cable.

2. The intended network’s DHCP Server will assign an IP address and the 10

GigE IP Mini-Converter will join that network.

3. Locate and connect to the AJA 10 GigE IP Mini-Converter.

Windows PC Host

A. Open Windows Explorer.

B. Navigate to the Network.

C. Click on the Network to enumerate network devices.

D. Search for either “IPT-10G2,” "IPR-10G2," or the device’s Serial Number.

E. Double-click on the intended 10 GigE IP Mini-Converter. The host machine

web browser will launch and display the web UI for the device.

macOS Host

A. Go to System Preferences > Sharing and turn on File Sharing.

B. Open the Finder Window.

C. Navigate to Shared > All…

D. Click on All… to enumerate network devices.

E. Search for either “IPT-10G2,” "IPR-10G2," or the device’s Serial Number.

F. Double-click on the intended 10 GigE IP Mini-Converter. The host machine

web browser will launch and display the web UI for the device.

NOTE: If the above does not work, then you will need to download and install an MDNS

browser to assist with discovering network devices on a macOS host.

Initial Setup By AJA eMini-Setup

1. Acquire AJA eMini-Setup (version 2.1) from the AJA website for either

macOS or Windows:

https://www.aja.com/family/software#eminisetup

2. Install eMini-Setup:

A. Unzip the Installer.

B. Run the .dmg file on macOS or the .msi file on Windows.

3. Connect Power to your AJA Ethernet equipped Converter.

4. Connect the USB cong cable to the computer running eMini-Setup.

5. Open eMini-Setup and congure the device’s network settings.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 13 www.aja.com

NOTE: DHCP is enabled by default, and if the device is connected to a DHCP server the IP

address field will populate.

6. Enter the IP address into a browser window. The web UI for your AJA device

will display.

7. Use the web UI to fully congure and control your AJA Device.

Settings Retained

The current 10 GigE IP Mini-Converter's configuration settings are retained even

when powered off, so subsequent installations for an identical decoding or

encoding session can be done with the following simple steps:

1. Apply power to the 10 GigE IP Mini-Converter.

2. Connect the unit to your network using the Control LAN, Media LAN 1 and

Media LAN 2 and connect the unit’s inputs and outputs.

NOTE: Three LAN connections to the unit are not necessarily required on an ongoing

basis. If it is desirable for your installation, after the 10 GigE IP Mini-Converter

is set up, you can access all control parameters through one of the Media LANs

with the appropriate network configuration. See "Networking Option – Using

Only the Media LAN Port for Control and Media Settings" on page 23 for more

information.

NOTE: The 10 GigE IP Mini-Converters pack an unprecedented feature set into the mini

converter box. As a result, the unit uses approximately 13 watts of power. It will be

very warm to the touch, which is normal. The unit is engineered to operate across

the full temperature range, from 0 to 40 degrees C.

NOTE: For highest reliability, the mini converters rely on convection cooling instead

of using a built-in fan. Therefore, when installing the units, mount in a

location where they have access to air for proper cooling. Do not stack the

10 GigE IP Mini-Converters with other mini converters or other powered

equipment.

REST API Documentation

AJA’s REST automation API provides a platform from which you can issue

commands to an AJA device’s internal web server, allowing remote systems

the ability to control AJA embedded or networked devices. With this control

framework, you can build integration and automation scripts, using any scripting

language, allowing you to take full advantage of the device’s functionality.

This documentation is available at the following link:

https://gitlab.aja.com/pub/rest_api

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 14 www.aja.com

Chapter 2 – eMini-Setup

Overview

This chapter describes using the eMini-Setup application to initially communicate

with and configure a 10 GigE IP Mini-Converter over a direct USB connection.

Once configured, the IP Mini-Converter can be accessed via an Ethernet network

using a web browser. Subsequently, that device can then be reconfigured over

that network, using its IP address and built-in web server.

NOTE: The eMini-Setup application is only used to setup selected Ethernet capable AJA

devices, and cannot be used to connect to or setup other AJA Mini-Converters.

The general procedure is:

1. Acquire eMini-Setup from the AJA website and install the eMini-Setup

application onto a computer.

2. Connect the IP Mini-Converter to that computer’s USB port.

3. Launch the eMini-Setup application.

4. Go to the Control Network tab and Media Network tabs, where the IP

address settings are displayed. You can use the existing DHCP assigned IP

address, or it can be changed manually.

5. You can also use eMini-Setup to load rmware to the device, although this

can also be done quickly and easily using the web browser interface.

Acquiring eMini-Setup

AJA’s eMini-Setup application is available for download from the AJA website.

To download the latest eMini-Setup package, which includes the eMini-Setup

application and documentation:

1. Go to:

https://www.aja.com/family/software#eminisetup

2. Click the link corresponding to the version you want to download for Mac or

Windows.

NOTE: IPT-10G2-SDI and IPT-10G2-HDMI require eMini-Setup version 2.1 or later.

IPR-10G2-SDI and IPR-10G2-HDMI require eMini-Setup version 2.0 or later.

IPR-10G-HDMI requires eMini-Setup version 1.3 or later.

eMini-Setup Documentation

Included with the eMini-Setup download is the AJA device's Installation and

Operation Guide, which can be accessed from the eMini-Setup UI via the Help/

Manual drop-down menu. This manual includes eMini-Setup information.

Documentation can also be accessed directly from the Mac eMini-Setup installer

in the Documentation folder.

Documentation included with the eMini-Setup application is the version available

at the time of distribution. However, AJA’s documentation can be updated

regularly, so newer versions may exist.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 15 www.aja.com

To download just the latest documentation, go to:

https://www.aja.com/products/mini-converters/ip-converters

Click the support button and open the Manuals link.

Installing eMini-Setup

PC Installation

To install eMini-Setup on a Windows PC:

1. Download the application from the AJA website. See "Acquiring eMini-Setup"

on page 14.

2. Open the AJA_eMini-Setup_win.zip le.

3. Double-click on the AJA_eMini-Setup.msi le.

4. The Setup Wizard will guide you through the installation.

Figure 9. eMini-Setup PC Wizard

5. Click Next to begin. Answer the questions in the subsequent dialogues,

including device software installation if displayed. When nished, an AJA

eMini-Setup shortcut will be installed on the desktop, and you will be able

to locate the eMini-Setup application in the AJA folder in the Programs

listing.

NOTE: If the eMini-Setup application already exists on the PC, a different Setup Wizard

appears.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 16 www.aja.com

Figure 10. eMini-Setup Wizard, Re-installation

With this screen you can Repair (reinstall) or Remove (uninstall) eMini-Setup on

the PC.

Mac Installation

To install the application on a Mac:

NOTE: Mac computers must be Intel-based (G5, G4 and earlier models will not work with

eMini-Setup).

1. Download the application from the AJA website. See "Acquiring eMini-Setup"

on page 14.

2. Unzip the le.

3. Double-click on the AJA eMini-Setup.dmg le.

4. Answer the prompt and a utility program will be launched.

Figure 11. eMini-Setup Mac Installer

5. To complete the installation drag the “AJA eMini-Setup” icon to the

Applications folder.

Running eMini-Setup

Connect your Ethernet capable AJA device to the PC or Mac via the supplied USB

cable, and then connect the external power supply (supplied) to that AJA device.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 17 www.aja.com

PC Startup

To run eMini-Setup on a PC, double-click on the AJA eMini-Setup icon on your

desktop, or open the AJA folder in the program list and click on the AJA eMini-

Setup application located inside the eMini-Setup folder.

Figure 12. Launching eMini-Setup on a PC

Mac Startup

To run eMini-Setup on a Mac, open the Applications folder and locate the AJA

eMini-Setup application. Double-click the application to launch it.

Operating eMini-Setup

The eMini-Setup application provides a graphical user interface for viewing

settings, modifying settings, and updating software.

Figure 13. Example eMini-Setup Screen

Tabbed

screens

Select an

attached

AJA device

LAN

connection

status

USB

connection

status

Selecting an AJA device from the pull down menu on the upper right causes

eMini-Setup to connect to the selected AJA device.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 18 www.aja.com

Version - The version of firmware installed in the AJA device is displayed below

the graphic.

Sn - This is the factory set unique serial number of your AJA device. If you ever call

AJA Support for service, you may be asked for this number.

A status field at the bottom of the screen shows if the eMini-Setup application is

connected and communicating with an AJA device.

File Menu - The File drop-down menu on the eMini-Setup application bar has a

Revert to Factory Settings menu item that allows you to change the settings

back to the AJA device’s factory defaults.

Edit Menu - The Edit drop-down menu has standard Cut, Copy and Paste

functions for editing text.

Help Menu - The Help drop-down menu has a link to the AJA device’s manual.

Control LAN Tab Screen

Figure 14. eMini-Setup Control LAN Tab Screen

Use this Control LAN tab to change the network setup on the connected AJA

device. You must click the Apply button to initiate any network configuration

changes.

IP Address Type - Choose from DHCP (default) or Static IP Address.

NOTE: A basic setup would be to run an Ethernet cable directly between the device and

your laptop and set both the computer and IPR to sequential static IP addresses.

This provides a rapid way to set up to access the web user interface.

IP Address - The current IP Address is displayed. A different IP address can be

entered.

Subnet Mask - The current Subnet Mask is displayed. A different subnet mask

can be entered.

Gateway - The current Gateway address is displayed. A different gateway address

can be entered.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 19 www.aja.com

UPnP Host - Choose from Enable or Disable to control whether the AJA device

makes itself visible for Windows network browsing.

MAC Address - This is the permanent MAC address of the Control LAN Ethernet

port of the AJA device.

Open Web Page - Opens the IP Mini-Converter's web interface in a web browser.

Media Network 1 Tab Screen

Figure 15. eMini-Setup Media LAN 1 Tab Screen

Use this Media LAN 1 tab to change the corresponding media network setup

on the connected AJA device. You must click the Apply button to initiate any

network configuration changes.

IP Address Type - Choose from DHCP or Static IP Address.

NOTE: If you intend to directly connect an IPT to an IPR, then you will need to use

sequential static IP addresses for both units (Transmit and Receive).

IP Address - The current IP Address is displayed. A different IP address can be

entered.

Subnet Mask - The current Subnet Mask is displayed. A different subnet mask

can be entered.

Gateway - The current Gateway address is displayed. A different gateway address

can be entered. On the Media LAN, the gateway may be left blank. (A gateway

is required on the Control LAN).

MAC Address - This is the permanent MAC address of the Media LAN Ethernet

port of the AJA device.

Open Web Page - Opens the IP Mini-Converter's web interface in a web browser.

10 GigE IP Mini-Converters SMPTE 2110 IP Transmit/Receive v2.1r1 20 www.aja.com

Media Network 2 Tab Screen

Figure 16. eMini-Setup Media LAN 2 Tab Screen

Use this Media LAN 2 tab to change the corresponding media network setup

on the connected AJA device. You must click the Apply button to initiate any

network configuration changes.

IP Address Type - Choose from DHCP or Static IP Address.

NOTE: If you intend to directly connect an IPT to an IPR, then you will need to use

sequential static IP addresses for both units (Transmit and Receive).

IP Address - The current IP Address is displayed. A different IP address can be

entered.

Subnet Mask - The current Subnet Mask is displayed. A different subnet mask

can be entered.

Gateway - The current Gateway address is displayed. A different gateway address

can be entered. On the Media LAN, the gateway may be left blank. (A gateway

is required on the Control LAN).

MAC Address - This is the permanent MAC address of the Media LAN Ethernet

port of the AJA device.

Open Web Page - Opens the IP Mini-Converter's web interface in a web browser.

La pagina sta caricando ...

AJA IPR-10G-HDMI Manuale utente

Questo manuale è adatto anche per

AJA IPR-10G-HDMI Manuale utente

in altre lingue

Documenti correlati

Altri documenti