ProLights 7x9W RGBW compact IP65 LED PAR Manuale utente

Marca: ProLights

Modello: 7x9W RGBW compact IP65 LED PAR

Categoria: Stroboscopi

Tipo: Manuale utente

Questo manuale è adatto anche per

USER MANUAL

MANUALE UTENTE

LUMIPAR7IP

EN - IT

SUPER-SLIM PARLED

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.001-09/17

Packing content

• LUMIPAR7IP

• Mount bracket

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specifications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 DMX Mode

3. 5 DMX configuration

3. 6 Linking

3. 7 DMX Addressing

3. 8 Settings

Screen

3. 9 Fixture Settings

Dimmer

White Calibration

LED Frequency

Factory Reload

3. 10 Fixture Information

3. 11 Operations in automatic mode

Master/Slave

Effects

Static Mode

3. 12 Connection of the DMX line

3. 13 Construction of the DMX termination

3. 14 DMX control

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Troubleshooting

LUMIPAR7IP

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modiﬁcations on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system ﬁtted with eﬃcient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualiﬁed electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the ﬁxture under the following conditions:

- in places subject to vibrations or bumps;

- in places with a temperature of over 45 °C.

• Make certain that no inﬂammable liquids, water or metal objects enter the ﬁxture.

• Do not dismantle or modify the ﬁxture.

• All work must always be carried out by qualiﬁed technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation deﬁnitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way diﬀerent to the one described in this manual, it may suﬀer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut oﬀ power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the ﬁxture’s being used.

• Install the ﬁxture in a well ventilated place.

• Keep any inﬂammable material at a safe distance from the ﬁxture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eﬀectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ﬂashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

• This product was designed and built strictly for the use indicated in this documentation. Any other use,

not expressly indicated here, could compromise the good condition/operation of the product and/or

be a source of danger.

• We decline any liability deriving from improper use of the product.

LUMIPAR7IP

- 1 - INTRODUCTION

1.1 DESCRIPTION

LUMIPAR7IP is a compact and ﬂexible IP LED PAR Can made for small concerts and theatres, and to perform

as architectural accent luminaire for outdoor events. The housing in die-cast aluminium is designed to

feature both as a robust workhorse and totally fan-free being totally silent during its operation.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE

• Source: 7x9W RGBW LEDs

• Luminous ﬂux: 20°: 2’945 lm - 45°: 3’835lm

• Lux: (20°) 1’923lx @3 m full

• Lux: (45°) 654lx @3 m full

• Source life expectancy: >50.000 h

OPTICS

• Beam angle: available in 20° or 45°

• Field angle: 36° or 60°

COLOUR SYSTEM

• Colour mixing: RGBW / FC

• White presets: 3.000 K ~ 10.000K

• Colour wheel: virtual colour wheel with presets

• Macros: built-in white presets

DYNAMIC EFFECTS

• Static colour mode: selection of static colour

• Manual colour mode: manual adjustment of colour

• Auto mode: built-in programs with execution speed adjustment

BODY

• Body: sturdy die-cast aluminium body conceived for long-time durability

• Body colour: black

CONTROL

• Protocols: DMX512

• DMX channels: 4 / 6 / 11channel

• Display: black OLED touch display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included

• Master/Slave: for synchronized operation of more units linked in a chain

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Dimmer curves: 4 diﬀerent dimming curves available

• Strobe / shutter: 0 - 30 Hz, electronic

• Operating temperature: -20° ~ +45°

• Flicker: ﬂicker free operation

• Selectable PWM: 600 ~ 25.000 Hz

LUMIPAR7IP

Technical drawing Fig.1

240

154

175

286

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 65W

• Power consumption (at 120 V): 64W

• Output (at 230 V): 58 units on a single power line

• Output (at 120 V): 31 units on a single power line

PHYSICAL

• Cooling: natural cooling of the peculiar chassis and to absence of fans

• Sospension and ﬁxing: double hanging bracket suitable for safe hanging and for ﬂoor positioning

• Signal connection: Seetronic XLR 5p IN/OUT connectors

• Power connection: Seetronic powerCON waterproof IN/OUT connectors

• IP rating: 65 for outdoor installations

• Dimensions (WxHxD): 240x286x154mm

• Weight: 3,64kg

LUMIPAR7IP

1.3 OPERATING ELEMENTS AND CONNECTIONS

Fig.2 - Rear panel

1. MOUNTING BRACKET.

2. LOCKING KNOB for the mounting bracket.

3. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them.

4. SAFETY EYE to attach safety cable.

5. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable.

6. DMX IN (5-pole XLR): 1 = ground, 2 = DMX-, 3

= DMX+, 4 N/C, 5 N/C.

7. GND POINT grounding the fixture to the earth.

8. DMX OUT (5-pole XLR): 1 = ground, 2 = DMX-,

3 = DMX+, 4 N/C, 5 N/C.

9. POWER OUT: connect to supply power to the

next unit.

5 9

64 8

LUMIPAR7IP

- 2 - INSTALLATION

2.1 MOUNTING

LUMIPAR7IP may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For ﬁxing, stable mounting clips are required. The mounting place must be of suﬃcient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the ﬁxture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (1).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the

bracket if is necessary.

Fig.3

LUMIPAR7IP

Fig.4 - Functions of the buttons

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch oﬀ, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and oﬀ via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the LED Display

(ﬁg.4).

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or confirm the

current function value or

option within a menu

LUMIPAR7IP

3.3 MENU STRUCTURE

1 CONNECT

DMX Address

Value (001-512)

DMX Mode

Easy 4CH

Basic 6CH

Standard 11CH

2 SETUP

Screen

Back Light

10S

20S

30S

Key Lock

NO-Yes

3 ADVANCED

Dimmer Mode

Off

Dimmer 1

Dimmer 2

Dimmer 3

White Balance

Off

Adjust Red <125-255>

Green <125-255>

Blue <125-255>

White <125-255>

Led Frequency

600Hz

1200 Hz

2000 Hz

4000 Hz

6000Hz

25kHZ

Factory Reload

NO-Yes

4 INFORMATION

Fixture TIme

0-9999

Version

V1.0

4 STAND ALONE

Maser/Slave

15D00217****

Eﬀects

Eﬀect1

……

Eﬀect5

Static

Fixed Color

RGB

RGW

RBW

GBW

RGBW

LUMIPAR7IP

White preset

3000K

4000K

5000K

6000K

7000K

8000K

9000K

10000K

Manual Color

Red <000-255>

Green <000-255>

Blue <000-255>

White <000-255>

3.4 DMX MODE

• Press the button MENU so many times until the display shows DMX ADDRESS, and press the button ENTER

to conﬁrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

To able to operate the LUMIPAR7IP with a light controller, adjust the DMX start address for the first a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX

channel, adjust the start address 33 on the LUMIPAR7IP. The other functions of the light effect panel are

then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

3.5 DMX CONFIGURATION

LUMIPAR7IP is equipped with diﬀerent DMX conﬁguration.

• Press the button MENU so many times until shows DMX CHANNEL, and press the button ENTER to conﬁrm.

• Select the desired DMX conﬁguration (Easy 4CH - Basic 6CH - Standard 11 CH ) through the buttons UP/DOWN.

The tables on page 14 indicate the operating mode and DMX value.

3.6 LINKING

Several units may be interconnected in order to control all further slave units to the same eﬀect of the

master unit. Use standard DMX cables to daisy chain your units together via the DMX connector on the

rear of the units. For longer cable runs we suggest a terminator at the last ﬁxture (see page 12).

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the ﬁrst slave unit.

2. Connect the DMX OUT of the ﬁrst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.7 DMX ADDRESSING

To able to operate the LUMIPAR7IP with a light controller, adjust the DMX start address for the first a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the first DMX

channel, adjust the start address 33 on the LUMIPAR7IP.

The other functions of the light effect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

6 33 33-38 39 45 51

11 33 33-41 44 55 66

LUMIPAR7IP

3.8 SETTINGS

You can change the parameters for the device by following these steps:

SCREEN

You can change the following parameters related to the display, following the same procedure:

• Press the ENTER button to access the main menu.

• Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to

enter the next menu.

• Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter

the next menu.

• Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-

play and press the ENTER key to display it.

- Back Light - Backlight display Auto Oﬀ. This feature allows you to automatically turn oﬀ the backlight

after a speciﬁed time that you can set using the arrow buttons. To have the display always on select

Always On or choose another value to turn oﬀ the display after the amount of time you choose.

- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function

is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-

tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, LEFT,

RIGHT, ENTER. Select YES to activate or NO to disable.

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3. 9 FIXTURE SETTINGS

It is possible to change the parameter value in the following way:

DIMMER

• Enter in Dimmer mode to select speciﬁc dimming curve, press the button MENU so many times until

shows DIM MODE, and press the button ENTER to conﬁrm.

• Press the button UP/DOWN to select OFF - DIM1 - DIM2 - DIM3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

DMX Address: 51DMX Address: 39DMX Address: 33 DMX Address: 45

Fig.5 - Example 6 DMX channels configuration

............

DMX512 Controller

LUMIPAR7IP

WHITE CALIBRATION

• Press the button MENU then press the button UP/DOWN so many times until show WHITE CALIBRATION.

Press the button ENTER to conﬁrm.

• Select the color Red, Green, Blue, White through the buttons UP/DOWN. Press the button ENTER to con-

ﬁrm.

• Set the value (125 - 255), using the buttons UP/DOWN.

• Continue until the desired setting is obtained.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

LED FREQUENCY

• To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED

Frequency, and then press the ENTER button.

• Select the frequency (600Hz - 1200Hz - 2000Hz - 4000Hz - 6000Hz - 25kHz) using the UP/DOWN buttons.

• To conﬁrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

FACTORY RELOAD

Select this function to restore the drive to default settings:

• To activate Reset Factory display press the button MENU so many times until shows Factory Reload,

and press the button ENTER to conﬁrm.

• Press ENTER button to conﬁrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automati-

cally.

3. 10 FIXTURE INFORMATION

To view all the information on the device, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER but-

ton to enter the next menu.

• Press the UP/DOWN button to scroll through the menu, then select one of the following information

and press the ENTER button to display it.

- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.

- Software Version - Through Version function you can display the currently installed software version.

• Press the LEFT button repeatedly to exit the menu.

3. 11 OPERATIONS IN AUTOMATIC MODE

MASTER SLAVE

Press the UP/DOWN button to scroll through the menu, select Master/Slave and press ENTER to conﬁrm your

choice.

• Press the UP/DOWN button to select the mode of operation:

- Master, if the unit is connected in series with other units and it acts as the Master;

- Slave, if the unit is not connected to other units.

• Press the ENTER button to conﬁrm your choice.

EFFECTS

The unit independently runs through its show. Before you send an automatic program you need to set the

drive as Master/Alone:

• Press the ENTER button to access the main menu.

LUMIPAR7IP

• Press the UP/DOWN button to scroll the menu, select the Effects icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to select the mode of operation: Effects 1, Effects 2, Effects 3, Effects 4 , Effects 5

• Press the ENTER button to conﬁrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The unit will go into automatic mode by executing the program automatically.

STATIC MODE

This ﬁxture has the ability to accept custom static color settings. Access these chases via the control panel

on the back of the ﬁxture.

• Press the button MENU so many times until the display shows STATIC, then press the button ENTER.

• Select Fixed Color through the buttons UP/DOWN, then press the button ENTER.

• Set the colors R, G, B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW, RGBW, through the buttons UP/DOWN,

then press the button ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

• Select White Presets through the buttons UP/DOWN, then press the button ENTER.

• Set the colors temperatur: 3000K, 4000K, 5000K, 6000K, 7000K, 8000K, 9000K, 10000K, through the buttons UP/

DOWN, then press the button ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

• Select Manual Color Mixer through the buttons UP/DOWN, then press the button ENTER.

• Set the colors Red, Green, Blue, White, through the buttons UP/DOWN, then press the button ENTER.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

LUMIPAR7IP

Fig.7

3.12 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty ﬁxture and controller operation.

Over long runs can be necessary to insert a DMX level matching ampliﬁer.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the ﬁrst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.13 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reﬂected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 3-pin male XLR

connector, as shown in ﬁgure.

Fig.6

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

5 pin XLR connector

LUMIPAR7IP

3.14 DMX CONTROL

4 CHANNELS

MODE

FUNCTION DMX

Value

4 Ch

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

6 CHANNELS

MODE

FUNCTION DMX

Value

6 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

11 CHANNELS

MODE

FUNCTION DMX

Value

11 Ch

DIMMER

0~100% 000 - 255

RED

0~100% 000 - 255

GREEN

0~100% 000 - 255

BLUE

0~100% 000 - 255

WHITE

0~100% 000 - 255

STROBE

No Function

Strobe slow to fast

000 - 010

011 - 255

COLOR MACRO

No Function

R 100%, G 0~100%, B 0%

R 100%~0%, G 100%, B 0%

R 0%, G 100%, B 0~100%

R 0% G 100%~0% B 100%

R 0%~100% G 0% B 100%

R 100% G 0% B 100%~0%

R 100% G 0%~100% B 0%~100%

R 100%~0% G 100%~0% B 100%

R 100% G 100% B 100% W100%

White presets 1

White presets 2

White presets 3

White presets 4

White presets 5

White presets 6

White presets 7

White presets 8

White presets 9

White presets 10

White presets 11

000 - 010

011 - 030

031 - 050

051 - 070

071 - 090

091 - 110

111 - 130

131 - 150

151 - 170

171 - 200

201 - 205

206 - 210

211 - 215

216 - 220

221 - 225

226 - 230

231 - 235

236 - 240

241 - 245

246 - 250

251 - 255

WHITE PRESETS

000 - 005 NO function

006 - 039 3000k

040 - 069 4000k

070 - 099 5000k

100 - 129 6000k

130 - 159 7000k

160 - 189 8000k

190 - 219 9000k

220 - 250 10000k

251 - 255 NO function

000 - 005

006 - 039

040 - 069

070 - 099

100 - 129

130 - 159

160 - 189

190 - 219

220 - 250

251 - 225

EFFECTS

No Function

Effect 1

Effect 2

Effect 3

Effect4

Effect5 (Effects1- 4)

000 - 010

011 - 060

061 - 110

111 - 160

161 - 210

211 - 255

EFFECTS SPEED

Effects speed slow to fast 000 - 255

DIMMER SPEED MODE

Preset dimmer speed from display menu

Dimmer speed mode off

Dimmer speed mode 1 (fast speed)

Dimmer speed mode 2 (middle speed)

Dimmer speed mode 3 (slow speed)

000 - 051

052 - 101

102 - 152

153 - 203

204 - 255

LUMIPAR7IP

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch oﬀ the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, ﬁxations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Remove the safety cap by a screwdriver.

3. Replace the blown fuse with a fuse of the exact same type and rating.

4. Install the safety cap, and reconnect power.

4.3 TROUBLESHOOTING

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the fixture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

REV.001-09/17

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al fine di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modificare, in

qualunque momento e senza preavviso, le specifiche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

• LUMIPAR7IP

• Staffa di fissaggio

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione

1. 2 Specifiche tecniche

1. 2 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menu

3. 4 Modalità DMX

3. 5 Configurazione canali DMX

3. 6 Collegamento

3. 7 Indirizzamento DMX

3. 8 Impostazioni del proiettore

Screen

3. 9 Funzioni dispositivo

Dimmer

Bilanciamento bianco

Frequenza LED

Factory reload

3. 10 Informazioni dispositivo

3. 11 Modalità automatica

Master/Slave

Effects

Modalità statica

3. 12 Collegamenti della linea DMX

3. 13 Costruzione del terminatore DMX

3. 14 Canali DMX

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi

LUMIPAR7IP

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eﬀettuare il collegamento ad un impianto di alimentazione dotato di un’eﬃciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori diﬀerenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eﬀettuate

da un installatore elettrico qualiﬁcato. Veriﬁcare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inﬁammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiﬁche all’unità.

• Tutti gli interventi devono essere sempre e solo eﬀettuati da personale tecnico qualiﬁcato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo deﬁnitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni diﬀerenti da quelle descritte nel presente

manuale, potrebbero veriﬁcarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inﬁammabili ad una distanza di sicurezza dall’unità.

• I ﬁltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro eﬃcienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

• Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa docu-

mentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare la funzionalità

del prodotto e/o rappresentare fonte di pericolo.

• Si declina qualsiasi responsabilità derivata dall’uso improprio del prodotto.

La pagina sta caricando ...

ProLights 7x9W RGBW compact IP65 LED PAR Manuale utente

Marca: ProLights

Modello: 7x9W RGBW compact IP65 LED PAR

Categoria: Stroboscopi

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: ProLights 7x9W RGBW compact IP65 LED PAR User manual

ProLights 7x9W RGBW compact IP65 LED PAR Manuale utente

Questo manuale è adatto anche per

ProLights 7x9W RGBW compact IP65 LED PAR Manuale utente

in altre lingue

Documenti correlati

Altri documenti