Agria 5900 Manuale del proprietario

4816

&

- 5900 231 / 232

- 2 cylinder B&S Vanguard

- Electric Starter Version

Before commissioning the machine, read operating

instructions and observe warnings and safety instructions.

Operating Instructions No. 998 761-A09.05

OutdoorPowerEquipmentOutdoorPowerEquipment

OutdoorPowerEquipment

Operating Instructions

for

Hydrostatic Tool Carrier

Taifun

2 Hydrostatic Tool Carrier Taifun

Symbols, Name Plate

Please complete:

Machine Type No.:.......................

ID/Machine No.:

...................................................

Engine Type:.................................

Engine No.:..................................

Date of Purchase:........................

For name plate, refer to

page 3/fig. A/4.

For engine type and number, refer

to page 58/fig. C/4.

Please state these data when

ordering spare parts to avoid wrong

deliveries.

Only use original agria spare parts!

Specifications, figures and

dimensions stated in these

instructions are not binding. No claims

can be derived from them. We reserve

the right for improvements without

changing these instructions.

This delivery comprises:

l

Operating instructions

l

Tool carrier

l

Tool kit

Symbols

Warning – danger

Important information

Fuel

Choke

Engine Start

Engine Stop

Battery charge indicator

Clutch

Forward

Reverse

Fast

Slow

Hydraulic system

PTO

Brake

Parking brake

Closed (locked)

Open (unlocked)

Clockwise

Anti clockwise

è - Serviceç= contact

Your agria-workshop

Hydrostatic Tool Carrier Taifun 3

Fig. A

Fig. B

Designation of Parts

12

4 Hydrostatic Tool Carrier Taifun

Designation of Parts

Fig. A:

1 Transmission / hydraulic oil dipstick and filling opening

2 Ball head for hood carrier front

3 Idle speed shifting mechanism (bypass)

4 Nameplate (vehicle identification-no.)

5 Ball head for hood carrier rear

6 Transmission venting plug

7 Loading belt

8 Steering handle locking bolt rollers

9 Steering handle, central screw

10 Lower steering handle

11 Steering bar

21 Eye bolt with cap nut, top

22 PTO-shaft

23 Eye bolt with cap nut, bottom

24 Transmission oil drain screw

25 Brake drum

26 Wheel hub

27 Oil filter cartridge

28 Engine

Fig. B:

1 Ball handle for lateral steering bar adjustment

2 Eccentric lever for central brake

3 Engine-off switch

4 Safety circuit lever

5 Engine clutch engagement lever

6 Pawl for engine clutch lever

7 Connection mechanism for PTO-shaft

8 Operating mechanism for steering handle lock

9 Speed adjusting lever

10 Twist grip for stepless adjustment of driving speed and forward-

reverse driving

11 Operating hour counter/speed counter (optional)

12 Lever for stepless adjustment of driving speed and forward-reverse

driving

Hydrostatic Tool Carrier Taifun 5

3

5

6

2

1

4

Index

Amount of Delivery ....................... 2

Designation

of Parts............................ 3, 58

Recommendations

Lubricants ..................................... 6

Maintenance and Repair .............. 6

Fuel ............................................... 6

1. Safety Instructions..... 7–12

2. Specifications

Dimensions ................................. 13

Track Widths ............................... 13

Machine ...................................... 14

Vibration Acceleration Value....... 14

Petrol Engine .............................. 15

Noise Levels ............................... 15

Operation on Slopes................... 15

3. Devices and Operating

Elements

Engine......................................... 16

Safety circuit................................ 17

Clutch .......................................... 18

PTO ............................................ 18

Transmission ............................... 19

Setting the Driving Speed

and Direction............................... 19

Coasting Operation..................... 20

Hydraulic Steering ...................... 20

Steering Handle.......................... 21

Loading Belt................................ 21

Drive-Wheels ........................ 22–23

Hood ........................................... 24

Axle Adjustment.......................... 24

Mounting and Dismounting

Implements ................................. 28

E-Starter Switch.......................... 26

Battery ........................................ 29

Electric Starter ............................ 29

4. Commissioning and

Operation

Commissioning the Machine ...... 30

Starting the Engine,

Electric Starter Version ............... 32

Shutting off the Engine,

Electric Starter Version ............... 33

Operation .................................... 34

Danger Zone............................... 34

Working on Slopes ..................... 35

5. Maintenance

Petrol Engine .......................36 - 42

– Engine Oil ................................ 36

– Air Filter ............................38 - 39

– Spark Plug ............................... 39

– Cooling System ....................... 40

– Carburetor................................ 41

– Battery ..................................... 42

Machine ...............................43 - 46

– Transmission/Hydraulic Oil ...... 43

– Steering Handle....................... 44

– Safety circuit............................. 45

– Adjustments on Levers .... 45 - 46

General Maintenance ................. 46

Storage ....................................... 47

6. Troubleshooting ....... 48 - 49

Electrical Wiring ................. 50

Varnishes, Wear Parts ....... 52

Lubrication Chart ............... 53

Hydraulic Hoses................. 47

Roller guard (optional) ....... 55

Inspection and

Maintenance Chart ............. 56

Conformity Declaration ..... 59

Note fold-out pages!

Figs. A + B............................. 3

Fig. C (Engine).................... 58

6 Hydrostatic Tool Carrier Taifun

Recommendations

Lubricants and

Anti-Corrosive Agents

Use the specified lubricants for engine

and transmission (see “Specifications”).

We recommend using bio-lubricating

oil or bio-lubricating grease for “open”

lubricating points or nipples (as specified

in the operating instructions).

We recommend using bio anti-corrosive

oil for preservation of machines and

implements (do not apply on painted

external covers). Oil can be brushed or

sprayed on.

Anti-corrosive agents are kind to the

environment and degrade fast.

Using ecologically safe bio-lubricants

and bio-anti-corrosives, you contribute

to environmental protection and to the

wellbeing of humans, animals and

plants.

Fuel

This engine runs smoothly on

commercial unleaded regular and

supergrade petrol as well as on leaded

supergrade petrol.

Do not add oil to petrol.

If, for environmental reasons, you use

unleaded petrol, make sure the fuel is

drained completely when shutting down

the engine for more than 30 days. This

is to prevent resin residues from

depositing in the carburetor, fuel filter,

and tank. Or add a fuel stabilizer.

For further instructions refer to „Engine

Preservation“.

Maintenance and

Repair

The trained mechanics of your agria

workshop carry out expert maintenance

and repair.

You should only carry out major

maintenance work and repairs on your

own, if you have the proper tools and

knowledge of machines and internal

combustion engines.

Do not hammer against the flywheel with

a hard object or metal tools as it might

crack and shatter in operation causing

injuries and damage. Only use suitable

tools for pulling the flywheel.

Hydrostatic Tool Carrier Taifun 7

1

1. Safety Instructions

Before starting the engine, read the

operating instructions and note:

Warning

This symbol marks all paragraphs in

these operating instructions which affect

your safety. Pass all safety instructions

to other users and operators.

Due Use

The tool carrier and the mounted

implements authorized by the

manufacturer have been designed for

all common applications and tasks in

farming and forestry, as e.g. grassland

mowing, this includes winter service and

ground clearing (due use).

Any other type of operation is

considered undue. The manufacturer is

not liable for any damage resulting from

undue use, for which the risk lies with

the user alone.

Due use includes compliance with

manufacturer’s instructions on

operation, maintenance and repair.

Any unauthorized changes to the tool

carrier render manufacturer liability null

and void.

General Instructions on

Safety and Accident

Prevention

Basic Rule:

The standard accident prevention

regulations must be adhered to, as well

as all other generally accepted rules

governing operational safety,

occupational health and road traffic

regulations.

For drives on public roads, the latest

traffic code applies.

Accordingly, check the tool carrier for

road and operational safety each time

you take up operation.

Only persons familiar with the tool carrier

and instructed on the hazards of

operation are allowed to use, maintain

and repair the tool carrier.

Young persons of 16 years or younger

may not operate the tool carrier!

Only work in good light and visibility.

Operator’s clothes should fit tightly.

Avoid wearing loosely fitting clothes.

Wear solid shoes.

Note the warning and instruction signs

on the tool carrier for safe operation.

Compliance is for your own safety.

When transporting the tool carrier on

vehicles or trailers outside the area to

be cultivated, ensure that the engine is

shut off.

8 Hydrostatic Tool Carrier Taifun

1

1. Safety Instructions

Careful with rotating tools – keep at a

safe distance!

Beware of coasting tools. Before you

start any maintenance or repair on them,

wait until tools have come to a complete

stop.

Foreign powered parts shear and crush!

Riding on the attachment during

operation is not permitted.

Implements and weights affect the

driving, steering, braking, and tip-over

characteristics of the tool carrier.

Therefore, ensure steering and braking

functions are sufficient. Match operating

speed to conditions.

Do not change settings of governor. High

engine speed increases risk of

accidents.

Working Area and Danger

Zone

The user is liable to third parties working

within the tool carrier’s working range.

Staying in the danger zone is not

permitted.

Check the immediate surroundings of

the tool carrier before you start it. Watch

out for children and animals.

Before you start work, clear the area

from any foreign object. During

operation, always watch out for further

objects and remove them in time.

For operation in enclosed areas, ensure

that a safety distance is kept to

enclosures to prevent damage to tools.

Operation and

Safety Devices

Before you start the engine

Become familiar with the devices and

operating elements and their functions.

Above all, learn how to turn the engine

off quickly and safely in an emergency

situation.

Ensure that all protective devices are

mounted and positioned to provide

protection.

With no implement mounted, make sure

PTO-shaft is covered with the protective

cap.

Starting the engine

Do not start engine in closed rooms. The

carbon monoxide contained in the

exhaust fume is extremely toxic when

inhaled.

Before you start the engine set all

operating elements to neutral or idling

position.

For starting the engine, do not step in

front of the tool carrier and the

implement.

Do not use assist-starting liquids when

using electrical assist-starting devices

(jumper cable). Danger of explosion.

Operation

Never leave the operator’s position at

the steering handle while tool carrier is

at work.

Never adjust the operating handles

during work – danger!

Hydrostatic Tool Carrier Taifun 9

1

1. Safety Instructions

For all works with the tool carrier, in

particular for turning, the machine

operator must keep the distance to the

machine given by the steering handles.

Riding on the implement during

operation or in transport is not permitted.

If clogging occurs in the implement, shut

off the engine and clean the implement

with an appropriate tool.

In case of damage to the tool carrier or

to the implement, immediately shut off

the engine and have it repaired.

If steering causes problems,

immediately bring the tool carrier to a

halt and turn it off. Have the malfunction

removed without delay.

To prevent the tool carrier from sliding

on slopes make sure it is secured by

another person using a bar or a rope.

This person must stay at a higher

position than the vehicle and at a safe

distance from the attachment at work.

If possible, always work across the

slope.

End of Operation

Never leave the tool carrier unattended

with the engine running.

Before you leave the tool carrier, shut

off the engine. Then close fuel taps.

Secure tool carrier against unauthorized

use. If tool carrier is equipped with

ignition key, remove the key. For all other

versions, remove spark plug connector.

Implements

Only mount implements with the engine

and PTO shut off.

Always use appropriate tools and wear

gloves when changing implements and

parts thereof.

For mounting and dismounting

implements bring stand into proper

position and ensure stability.

Secure tool carrier and implements

against rolling off (parking brake, wheel

chocks).

Beware of injuries while coupling

implements. Work with particular care.

Hitch implements as specified and only

couple at specified points.

Secure tool carrier and implement

against unauthorized use and rolling off

when you leave the machine. If

necessary, install transport or security

devices and secure.

Mowing Implement

Handle with care! Sharp blades of the

cutter bar may cause injuries! Remove

knife guards only for mowing and refit

immediately after work has finished.

For transport and storage always mount

the knife guards. Secure finger bars

additionally with tension springs.

Do not transport the dismounted cutter

bar without knife guards.

10 Hydrostatic Tool Carrier Taifun

1

1. Safety Instructions

When mounting and dismounting the

cutter bar, make sure all blades are

protected by the knife guards.

To exchange the knife and to mount/

dismount the knife driver, make sure that

you turn screws away from cutting

blades.

For grinding the mowing knives, always

wear safety goggles and gloves.

Weights

Fit weights properly and at specified

points.

Maintenance

Never carry out any maintenance or

cleaning with the engine running.

Before you work on the engine, always

remove spark plug connector.

Check regularly and, if necessary,

replace all protecting devices and tools

subject to wear and tear.

Replace damaged cutting tools.

Always wear safety gloves and use pro-

per tools when exchanging cutting tools.

Do not carry out repairs like welding,

grinding, drilling, etc. on structural and

safety-relevant parts (e.g. hitch)!

Keep tool carrier and implement clean

to avoid risk of fire.

Check nuts and bolts regularly for tight

fit and re-tighten, if necessary.

Ensure that you re-install all safety and

protective devices and adjust them

properly after maintenance and

cleaning.

Only use original agria spare parts. All

other commercial spare parts must

correspond to quality and technical

requirements specified by agria.

Storage

It is not allowed to store the tool carrier

in rooms with open heating.

Never park the tool carrier in closed

rooms with fuel left in tank. Fuel vapours

are hazardous.

Engine, Fuel, and Oil

Never let the engine run in closed

rooms. Extreme danger of intoxication!

For the same reason, also replace

damaged exhaust pipe immediately.

Be careful when handling fuel. Great

danger of fire! Never refill fuel close to

open fire, inflammable sparks or hot

engine parts. Do not refill fuel in closed

rooms. Do not smoke when refilling!

Refill only with the engine shut off and

cooled down.

Hydrostatic Tool Carrier Taifun 11

1

1. Safety Instructions

Do not spill any fuel, use a proper filling

device (e.g. funnel).

In case of fuel-spillage, pull the tool

carrier away from the spillage before you

start the engine.

Make sure fuel is of specified quality.

Store fuel in approved cans only.

Liquids leaking under high pressure, e.g.

fuel, can penetrate the skin and cause

severe injuries. Immediately see a

doctor.

Store anti-corrosive agents and

stabilizing liquids out of reach of

children. If sickness and vomiting occur,

see a doctor. If fuel has contacted eyes,

rinse them thoroughly, avoid inhaling of

vapours.

Read and observe enclosed

instructions.

Before you dispose of opened and

seemingly empty pressurised tins (e.g.

of assist-starting liquids) make sure they

are completely empty. Empty them in

ventilated places safe from spark

formation or flames. If necessary,

dispose of tins in hazardous waste

deposits.

Be careful when draining hot oil, danger

of burns.

Make sure oil used is of specified quality.

Storage is in approved cans only.

Dispose of oil, greases, and filters

seperately and properly.

Hydraulic System

The hydraulic system is subjected to

high pressure.

When connecting hydraulic motors,

ensure the specified connection of the

hydraulic hoses.

Hydraulic oil emerging under high

pressure may penetrate the skin and

cause serious injuries.

In case of injuries, immediately consult

a physician – risk of infections.

Prior to works on the hydraulic system,

render the latter pressureless and shut

down engine (specialized workshop).

When searching leakages, use suitable

aids considering the risk of injuries

(specialized workshop).

Regularly check hydraulic hose lines for

damage and ageing and replace them,

if necessary.

Only use original agria hydraulic hoses.

Tyres and

Tyre Air Pressure

When working on wheels, make sure

tool carrier is parked properly and

secured against rolling off.

Any repairs are to be carried out by

trained mechanics only and with the

appropriate tools.

Regularly check tyre air pressure.

Excessive pressure may cause bursts.

12 Hydrostatic Tool Carrier Taifun

1

1. Safety Instructions

Use appropriate tyre air pressure for

operation with implements.

Re-tighten attachment bolts of drive-

wheels or check tightness when doing

maintenance work.

Electrical System and

Battery

When working on the electrical system,

make sure the battery is disconnected

(negative pole) (for tool carriers

equipped with battery).

Make sure to connect battery properly

– first connect positive pole and then

negative pole. Disconnect in reverse

order.

Be careful with battery gases – explosi-

ve!

Avoid spark discharge and open flames

near batteries.

Remove plastic cover (if included) to

recharge battery to prevent highly ex-

plosive gases from building up.

Be careful when handling battery acid!

Only use specified fuses. Stronger fuses

will destroy the electrical system –

danger of fire.

Always cover positive pole with specified

cover or terminal cap.

Persons having a pacemaker may not

touch live parts of the ignition system

when the engine is running.

Explanation of

Warning Signs

Before any cle-

aning, mainte-

nance, and repair

work shut off the

engine and pull

spark plug connec-

tor.

Do not work without

protective covers

mounted. Before

starting the engine,

bring covers in pro-

per position.

With engine

running, keep at a

safe distance from

cutting knife.

Do not touch

moving machinery

parts. Wait until

they have come to

a complete stop.

With engine

running, keep at a

safe distance.

Signs

When working with the

machine, wear individual

protective ear plugs.

Wear protective gloves.

Hydrostatic Tool Carrier Taifun 13

2

Dimensions: a

1

; e

1

= axle displaced forwards

2. Specifications

a a

1

b c e e

1

h

l

5.00-10 AS

20x8.00-10

21x11.00-8

5.00-12 AS

23x8.5-12

23x10.5-12

1360

ca. 990270

270 167Vanguard 550 623 790

(mm)

290 ca. 1010

Machine

Track Widths Table

[mm]

AS = Field tyre

R = Grass tyre

TG = Terra tyre

Version with continuous partial axle always + 40 mm

* = intermediate flange Vario .............................. 5916 211

)

1

= + track-width adjuster 90 mm ........... 5519 031

)

2

= traction cage wheels 10" .............................. 5917 011

)

3

= traction cage wheels 12"............................... 5917 021

A S i A S i

*+1

A

*+2

A

*+3

A

*+4

A

*+5

A A A

1

23x8.5-12 830 617 404 1056 843 630 1466 1346 1310

)3

1536

)3

2

23x10.5-12 955 691 427 1033 769 505 1443 1561 1323 1335

)3

1513

)3

3 5.00-12 AS 790 636 480 980 825 670 1390 1240 1270

)3

1460

)3

4 5.00-10 AS 800 655 510 950 805 660 1200 1280

)2

1430

)2

5 20x8.00-10 R 890 683 478 980 775 570 1270

6

21x11.00-8 TG )

1

1154 875 596 1234 955 676 1634

)2

14 Hydrostatic Tool Carrier Taifun

2

2. Specifications

Machine

Clutch: ............. Single disc dry clutch

Transmission: ....................Hydrostat

Driving speeds

Forward:............................ 0–7.0 km/h

Reverse:............................ 0–3.6 km/h

PTO: ...................................... 805 rpm

gear independent

at 3600 engine rpm

direction of rotation:

clockwise, looking on PTO,

constant in forward and reverse

Steering:

Fully hydraulic steering handle

Steering handle fixable with

disconnection of the hydraulic system

for manual steering

Steering handle: ... height adjustable,

side adjustable without tools

Oil for transmission and hydrostat:

optionally:

l

Multi-purpose oil:

SAE 10W-40 API-SE/SF (or higher)

l

Bio hydraulic oil:

Synthetic ester basis ................ HEES

Viscosity as per ISO .................VG 46

Purity class ........min. 16/13-ISO 4406

e.g.

ARAL:............................Vitam EHF 46

BP: ............................... Biohyd SE 46

ESSO: ....................................... HE 46

FUCHS:..................... Plantohyd S 46

PANOLIN: ..................... HLP Synth 46

Filling volume at

First filling: ............................ abt. 7.0 l

Oil change:............................ abt. 5.0 l

Oil filter:.. Screw-type cartridge AW 14

Vibration acceleration value:

on handlebar grip:............. a

hw

2.5 m/s

2

in accordance with EN 12733.

Weights:

Empty weight:

(with fuel tank filled up):

without with

drive wheels 23x8.5-12

El. Starter Vers. 186.5 kg 218.5 kg

Tyres: . 23x8.5-12 wide track field tyre

(series equipment)

optionally:

0190 11

2..................5.00-10 field tyre

3490 411.................. 5.00-12 field tyre

3490 511.......20x 8.00- 10 grass tyre

3490 611........ 21x11.00- 8 terra tyre

for this Terra-Grip design, track-width

adjusters are required:

5519 031................................2 x 9 cm

5990 71123x10.5-12 wide-track field tyre

Tyre air pressure at:

5.00-10 ....................................1.5 bar

5.00-12 ....................................1.5 bar

21x11.00- 8..............................0.8 bar

20x8.00- 10..............................0.8 bar

23x8.5-12.................................1.3 bar

23x10.5-12...............................1.3 bar

5917 011 .... Traction cage wheels10”

for 5.00-10AS

5917 541.....Traction cage wheels 12"

(5.00-12; 23x8.5-12; 23x10.5-12)

Drive-wheel attachment

and application ......... see page 22–24

Hydrostatic Tool Carrier Taifun 15

2

2. Specifications

Petrol Engine

Manufacturer: ............................ B&S

Type: ....................... Vanguard 18 HP

Version: ....................... Fan-air-cooled

2 cylinder-4-stroke

OHV engine (petrol)

Bore: ....................................... 72 mm

Stroke: .................................... 70 mm

Cubic capacity: ................... 570 ccm

Output: .................... 13.2 kW (18 hp)

at 3600 rpm

Max torque: ........ 33 Nm at 2600 rpm

Spark plug: ................. Bosch FR8DC

CHAMPION RC 12YC

Spark plug gap 1.0 mm

Ignition:

Electr. magnetic ignition, contactless

Air gap ............................. 0.2–0.3 mm

Radio remote screened ............ as per

VDE 0879

Valve clearance (engine cold):

Intake and outlet ............ 0.1–0.16 mm

Starter: ..........................Recoil starter

Electrical starter: ........................ 12V

Battery ................................ 12V 20Ah

Generator.......................... 12V 192 W

Fuel: ...................... Commercial petrol

min. octane number 85 RON

(refer to fuel recommendations)

Fuel tank capacity: .............abt. 7.5 l

Fuel consumption: ......... 312 g/kWh

Fuel filter: ..........................feul-online

Air filter:.......... Dry filter element with

foamed preliminary filter

Carburetor:........................ Horizontal

float carburetor

Rated speed:......................3600 rpm

Top no-load speed: ..........4000 rpm

Idling speed: ......................1750 rpm

Engine oil:

Filling quantity................. approx. 1.7 l

Multi-grade oil

at ambient temperature -15° to +45°C:

SAE 10W-40 API-SE/SF (or higher)

at ambient temperature -25° to +15°C:

SAE 5W-20 API-SE/SF (or higher)

Lubrication system:

Oil circulation lubrication

Oil pressure:

in the idle run .................min. 0.35 bar

Oil filter......................... Filter cartridge

Noise level:

with flail mower 100 cm

In accordance with EN 12733 appendix B:

Noise level

at operator’s ear ........... L

P

= 92 dB(A)

In accordance with 2000/14/EC, appen-

dix III, part B, chapter 32 lawn mower:

Acoustic power level: L

W

= 104 dB(A)

Operability on Slopes:

Engine is suited for use on slopes (with

oil level at “max” = upper level mark)

possible up to...45° inclination (100%)

16 Hydrostatic Tool Carrier Taifun

33

3. Devices and Operating Elements

The tool carrier agria type 5900 Taifun

is a base power machine and is always

operated with an implement mounted.

Therefore, the machine is suited for all

common applications in farming and

forestry, as well as for winter service.

Available implements:

• Front implements for

– mowing

– sweeping

– snow clearing and tilling

– gravel and salt spreading

For a choice of further attachments refer

to our price-list.

Engine

l

The four-stroke petrol engine runs

on commercial petrol (refer to fuel

recommendations page 6).

Ignition System

The engine is equipped with a

contactless ignition system. We

recommend to have necessary check-

ups done by an expert only.

During the first 20 operating hours

(break-in period) do not use engine to

maximum power.

Even after break-in period never use

engine at higher speed than necessary

for the work in hand.

I

High engine speed is harm-

ful to any engine and consid-

erably affects its durability. This

applies especially for no load

operation. Any overspeed (have the

engine roar) can result in immediate

damage.

Cooling System

The cooling system is fan-cooled.

Therefore keep screen at recoil starter

and cooling fins of cylinder clean and

free from sucked-in plant trash.

Idling-speed

Always ensure that idling-speed is

adjusted correcty. At low speeds and

with the speed control lever set to idle,

the engine is supposed to run smoothly

and without run-out.

Air Filter

The air filter purifies the air intake. A

clogged filter reduces engine output.

Hydrostatic Tool Carrier Taifun 17

3

3. Devices and Operating Elements

Speed Control Lever

The speed control lever (B/9) on the

steering handle is for stepless setting

of engine speed from min. = idle to max.

= full throttle.

Engine Shut-off Switch

The tool carrier is equipped with an

electric shut-off switch (B/3). On

pressing the switch, the ignition is turned

off (engine is shut off).

Position “I” = Operation

Position “0” = Engine off

I

The engine shut-off switch also

serves to shut off the engine

in an emergency situation. Set the

switch to “0” for fast shut-off.

Safety circuit

The tool carrier is equipped with a safety

circuit lever (B/4). When releasing the

lever, the ignition system is turned off

(engine is shut off).

 Stop position: When releasing the

lever, the ignition system is turned off

(engine is shut off). Beware – engine

keeps running due to centrifugal mass.

Start position: For starting the

engine and for short breaks, pull the

clutch lever (B/5) and lock with pawl (B/6).

 Operating position: To operate the

machine press safety circuit lever (B/4).

W

Do not fasten safety circuit

lever.

I

The safety circuit lever also

serves to shut off the engine

in an emergency situation. Release

the safety circuit lever for fast engine

shut-off. The lever automatically goes to

STOP position.

B/3

B/4

B/6

B/5

Stop







max

min

18 Hydrostatic Tool Carrier Taifun

B/7

3

3. Devices and Operating Elements

Clutch

The tool carrier is

equipped with a

single disc dry

clutch which is

operated via the

clutch lever (B/5).

l

Watch for the

correct clutch

play to avoid

clutch slipping

away during

operation.

I

Do not park the machine with the

clutch pulled and the engine

running. This may damage the clutch

release bearing.

Ensure the lever is pulled (pawl locked

in place) when you park the machine

with the engine

stopped, other-

wise clutch pro-

blems may result

due to corrosion.

PTO-Shaft Connection

The speed-independent PTO (A/22) is

connected with a connection mechanism

(B/7). With the connection mechanism

drawn backwards, the PTO-drive is

connected, when slid forwards, the PTO-

drive is disconnected.

B/5

45

Hydrostatic Tool Carrier Taifun 19

B/12

3

3. Devices and Operating Elements

Transmission

The agria tool carrier is equipped with a

hydrostatic drive.

Setting the Driving Speed and

Direction

Twist-grip shift model

l

The driving speed forward or reverse

is steplessly set or changed with the twist

grip (B/10).

l

The zero-position is set, when the

marking at the twist grip is congruent

with the “0” at the pictogram.

l

When swiveling the twist grip clockwise,

the driving speed is steplessly increased

forwards.

l

When swiveling the twist grip anti

clockwise, the driving speed is steplessly

increased backwards.

l

The locking lever

can be used to

prevent the twist-

grip from turning

accidentally.

Locking lever

= locked

Locking lever

= unlocked

Lever shift model

l

The driving speed forward or reverse

is steplessly set or changed with the

forefinger or the thumb at the driving

lever (B/12).

l

The zero-position is set, when the

marking at the driving lever is congruent

with the “0” at the pictogram and is in

contact with the spring detent.

l

When turning the driving lever

forwards, the driving speed is steplessly

increased forwards and accordingly

backwards, if the driving lever is turned

backwards and down.

B/10 Marking

20 Hydrostatic Tool Carrier Taifun

3

3. Devices and Operating Elements

Coasting Operation

The machine can be coasted without

engine, if the idle shift is opened

(position “0”).

The idle shift (A/3) is arranged at the

right front of the tool carrier underneath

the hood and can be operated by turning

the shifting knob (or shifting lever).

The hydraulic drive is activated again,

when the idle shift is closed (position “I”).

Prior to starting the works, check shifting

position!

I

Coasting operation or towing

up to max. 4 km/h.

Trailing is not permitted!

Hydraulic Steering

With the hydraulic steering, the inner

wheel at the curve becomes slower up

to the standstill, the outer wheel at the

curve keeps it velocity.

Steering

l

By the steering

movement at the

steering handle, the

hydraulic steering is

activated with running

engine.

l

Steering only during

driving, not upon a

standstill.

l

The stronger the

steering movement, the

quicker the hydraulic

steering

Locking the Hydraulic Steering

By pulling and turning the shifting

mechanism (B/8), the hydraulic steering

is locked and steering is realized by

muscular strength.

When the lock is opened, the hydraulic

steering is connected again.

Use: Operation at the slope!

– similar to a differential lock!

or for lifting out an implement.

B/8

A/3

La pagina sta caricando ...

Agria 5900 Manuale del proprietario

Agria 5900 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti