DTS FOS 100 FULL RGBW Manuale utente

GB

Made in Italy

FOS 100 FULL RGBW

FOS 100 FULL WHITE CT

User’s Manual rel 4.1 FC-CT

D.T.S. Illuminazione s.r.l. - ITALY

http://www.dts-lighting.it

FOS 100 SOLO FULL RGBW FOS 100 FULL RGBW

FOS 100 SOLO FULL WHITE CT FOS 100 FULL WHITE CT

FOS 100

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia

non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo

documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso

scritto della D.T.S .

DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di

design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei

prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and checked. However, no

responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,

photocopied or reproduced, in part or completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products

without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits

described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand

soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits

réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,

sans le consentement préalable de .

se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou

de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou

sur l'application des produits ou des circuits décrits.

D.T.S

D.T.S.

Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y

controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.

Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado

o reproducido, total o parcialmente, sin previa autorizaciónescrita de

se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter

estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de

ningún tipo sobre la utilización o sobre la aplicació

n de los productos o de los circuitos descritos.

D.T.S.

2

DESCRIPTION

M12 connection system between Power supply and LED bar (All versions)

Powercon + XLR connectors (FOS 100 SOLO IP20)

Harting connectors (FOS 100 SOLO IP65 )

FOS 100 is a new compact self-contained LED bar designed for colouring large surfaces with a uniform

projection, either indoor and outdoor.

FOS 100 can be used for many applications, such as: professional, for an ample range of special events;

theatre and television, for uniform background colours and cycloramas; architectural, for lighting building

facades, public and commercial spaces, monuments, etc.

FOS 100 is made on aluminium and steel offering high resistance to mechanical stress, with an IP65

protection rating.

FOS 100 length is 99 cm.

Various FOS 100 units can be easily connected together: the LEDs distribution pattern guarantees no

black spaces between the LEDs of in-line bars, and an even coverage of lighted surfaces.

FOS 100 is available with or without a Z10 integrated power supply.

The Z10 power supply is available either with IP65 or IP20 protection rating.

Three dedicated lenses sets (Spot, Medium flood, Wide flood) are available for each model, offering

different light beam projection angles.

FOS 100 SOLO can be controlled via any DMX lighting console.

FOS 100 range comprises various models, which employ different sets of LEDs tailored for distinct

applications:

FOS 100 FULL RGBW

FOS 100 FULL WHITE CT

FOS 100 FULL RGBW and FOS 100 SOLO FULL RGBW

15 x Ostar FULL RGBW LEDs • Integrated power supply (FOS 100 SOLO FULL RGBW)

FOS 100 FULL WHITE CT and FOS 100 SOLO FULL WHITE CT

15 x Ostar FULL WHITE LEDs • Integrated power supply (FOS 100 SOLO FULL WHITE CT)

All FOS 100 SOLO models are available with Z10 power supply IP65 or IP20 rated

All FOS 100 models are also available without integrated power supply

All FOS 100 models are also available with spot / medium flood / wide flood lenses

LED technology

FOS 100 / FOS 100 SOLO FULL RGBW: 15 x Ostar FULL RGBW LEDs

16 million colours; colour temperature range 2700°K ÷ 8000°K

FOS 100 / FOS 100 SOLO FULL WHITE CT: 15 x Ostar FULL WHITE LEDs

16 million colours; colour temperature range 2700°K ÷ 6500°K

No infrared emission; no ultraviolet emission

LEDs average lifespan: 100.000 hours

Optical units

3 lenses sets available (Spot, Medium flood, Wide flood)

Control

Via any DMX lighting console

Protection

FOS 100: IP65 protection level

FOS 100 SOLO: IP65 or IP20 protection level

Construction

FOS is made on aluminium and steel

Power supply

Integrated (FOS 100 SOLO) power supply / LED controller (Z10 IP65 or Z10 IP20);

External (FOS 100) dedicated Z1 PLUS (IP20 or IP65) or Z8 power supplies / LED controllers

Power consumption

Max 110W

Connection

3

FOS 100

MAIN ELECTRICAL CHARACTERISTICS (FOS 100 SOLO FULL RGBW / FULL WHITE CT)

Input Voltage Range : Vin 90 - 260 VAC

Frequency : 50 - 60 Hz

Power Factor (Pf) : 0.95 electronic PFC controller

Efficiency : 90% typical

Output:

Output Current : 350 mA @ 100% per channel (500mA @ 100% per channel in BOOST Mode)

Output Voltage : Vout 70V

Control Input:

Control Signal : DMX 512

Dimming System : Constant Current PWM

Address Range : DMX 512 channels addressable by display

ACCESSORIES

• Lenses set Spot available for each model

• Lenses set Medium flood available for each model

• Lenses set Wide flood available for each model

• 4x2xAWG24 Multipolar black cable (Code 0509C062)

• M12 female (8 poles) cable connector (Code 0520P050)

• M12 male (8 poles) cable connector (Code 0520P051)

• Z1 PLUS IP20 Power supply / LED controller (Code 03.LA.009P)

• Z1 PLUS IP65 Power supply / LED controller (Code 03.LA.009P.IP65)

• Z8 IP20 Power supply / LED controller (Code 03.LA.075.V2)

IMPORTANT SAFETY INFORMATION

Fire prevention:

Never locate the fixture on any flammable surface.

Minimum distance from flammable materials: 10 cm.

Replace any blown or damaged fuses only with those of identical value.

Prevention from electric shock:

High voltage is present inside the unit.

Unplug the unit prior to performing any operation which involves touching the inside of the unit.

This equipment must be grounded, do not connect to non-grounded supplies.

Use only AC supplies 90-260 V, 50-60 Hz.

FOS 100 SOLO IP20 model should never be located in position exposed to rain or in areas of

extreme humidity.

A good air ventilation is essential for proper equipment work.

Safety:

The external surface of the unit may exeed 50°C; never handle the unit until at least 5 minutes

have elapsed since the unit was turned off.

The use of a thermal magnetic circuit breaker is recommended for each FOS 100 SOLO unit.

4

FOS 100

UNIT DIMENSIONS:

FOS 100 SOLO FULL RGBW

FOS 100 SOLO FULL WHITE CT

990 mm

100 mm

Unit Dimensions

(LxWxH)

990 x 100 x 78 mm

Weight

7 Kg

78

mm

1

6

0

mm

140 mm

Packing Dimensions

(LxWxH)

1060 x 160 x 200 mm

Weight

8,5 Kg

5

FOS 100

Packing Dimensions

(LxWxH)

1060 x 160 x 200 mm

Weight

7 Kg

990 mm

56 mm

78

mm

1

6

0

mm

140 mm

Unit Dimensions

(LxWxH)

990 x 56 x 78 mm

Weight

5,5 Kg

UNIT DIMENSIONS:

FOS 100 FULL RGBW

FOS 100 FULL WHITE CT

6

FOS 100

INPUT/OUTPUT CONNECTIONS

FOS 100 SOLO IP20 FULL RGBW

FOS 100 SOLO IP20 FULL WHITE CT

Mains 90-260 V AC

50-60 Hz input Powercon

Female panel connector

DMX IN/OUT

XLR 5 pins Male / Female

Panel Connectors

7

Pin1

2

3

4

5

6

7

M12 LED output

Female panel connector

Mains 90-260 V AC

50-60 Hz output Powercon

Female panel connector

MAX load:

230 V AC = 20 FOS 100 SOLO

100 V AC = 10 FOS 100 SOLO

Pin1

2

3

4

5

6

7

M12 LED input

Male cable connector

FOS 100

LEDs Connector PinOut

4-GREEN - / WHITE 2 -

5-BLUE + / WHITE 3 +

6-BLUE - / WHITE 3 -

7-AMBER - / WHITE 4 -

8-AMBER + / WHITE 4 +

1-RED + / WHITE 1 +

2-RED - / WHITE 1 -

3-GREEN + / WHITE 2 +

7-

8

M12 LED output

Female panel connector

INPUT/OUTPUT CONNECTIONS

FOS 100 SOLO IP65 FULL RGBW

FOS 100 SOLO IP65 FULL WHITE CT

Mains 90-260 V Ac

50-60 Hz output ILME 5 pins

Female panel connector

MAX load:

230 V AC = 20 FOS 100 SOLO

100 V AC = 10 FOS 100 SOLO

DMX IN/OUT

ILME 4 pins Female

Panel Connectors

8

M12 LED output

Female panel connector

Mains 90-260 V Ac

50-60 Hz input cable

M12 LED input

Male cable connector

FEMALE PANEL

CONNECTOR

MAINS OUTPUT

1

3

2

4

FEMALE PANEL

CONNECTOR

DMX IN-OUT

LEDs Connector PinOut

FOS 100

Pin1

2

3

4

5

6

7

Pin1

2

3

4

5

6

7

8

DMX IN/OUT

ILME 4 pins Female

Panel Connectors

4-GREEN - / WHITE 2 -

5-BLUE + / WHITE 3 +

6-BLUE - / WHITE 3 -

7-AMBER - / WHITE 4 -

8-AMBER + / WHITE 4 +

1-RED + / WHITE 1 +

2-RED - / WHITE 1 -

3-GREEN + / WHITE 2 +

7-

INPUT/OUTPUT CONNECTIONS

FOS 100 FULL RGBW

FOS 100 FULL WHITE CT

FOS 100

M12 LED input

Male cable connector

LEDs Connector PinOut

For application where IP65 rating is not necessary, FOS 100 cabling connection can be

done with a standard UTP B2 category 5E cable.

The maximum distance between power supply and the unit should not exceed 100

meters (Z1 PLUS or Z10 LED Controller) or 50 meters (Z8 LED Controller).

For IP65 rating application, D.T.S. reccomend the use of a IP65/68 cable as the

Multipolar black cable (IP68) (D.T.S. Code: 0509C062).

The maximum distance between power supply and the unit should not exceed 100

meters (Z1 PLUS or Z10 LED Controller) or 50 meters (Z8 LED Controller).

TIA/EIA 568-

Pin1

2

3

4

5

6

7

8

9

4-GREEN - / WHITE 2 -

5-BLUE + / WHITE 3 +

6-BLUE - / WHITE 3 -

7-AMBER - / WHITE 4 -

8-AMBER + / WHITE 4 +

1-RED + / WHITE 1 +

2-RED - / WHITE 1 -

3-GREEN + / WHITE 2 +

7-

DMX SIGNAL CONNECTION:

FOS 100 SOLO IP20 FULL RGBW

FOS 100 SOLO IP20 FULL WHITE CT

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or

between units must be carried out using a two pair screened ø 0.5 mm.

P. S :

If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor Between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX

connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN

projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to

the DMX IN plug of the second one.

In this way, all the projectors are cascade connected.

The standard configuration of the FOS 100 SOLO is with XLR 5 pins connectors.

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

STANDARD

DMX 512

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

FOS 100

10

UNIT 1 UNIT 2 UNIT 3

DMX SIGNAL CONNECTION:

FOS 100 SOLO IP65 FULL RGBW

FOS 100 SOLO IP65 FULL WHITE CT

The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or

between units must be carried out using a two pair screened ø 0.5 mm.

P. S :

If the display showing the DMX address flashes, then one of the following errors has occurred:

- DMX signal not present

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest to use a DMX

terminator.

The DMX terminator is a male DMX cable connector with a 120 ohm resistor Between pin 2 and 3.

The DMX terminator must be plugged into the DMX out panel connector of the last unit connected to

the DMX line.

Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX

connector chassis. The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX

IN plug of the second one.

In this way, all the projectors are cascade connected.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE DMX CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

5

3

4 2

1

1=GND

2=DATA-

3=DATA+

CONTROLLER

STANDARD

DMX 512

MALE CABLE

CONNECTOR

DMX

120 OHM

11

FOS 100

DMX ADDRESS

Projector 1 A001

Projector 2 A011 If you want to select the next projector, just add “10”

Projector 3 A021

….. A….

projector 6 A051

Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX address. The numbers on the

display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the

projector is now controlled by the new DMX address.

TIPS: if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and

you get a faster selection.

FOS 100 SOLO FULL RGBW and FOS 100 SOLO FULL WHITE CT can be used in seven different

modes: 10 DMX channels mode (default), 6 DMX channels mode (Shutter + Dimmer + RGBA),

WALL mode (6 DMX channels; for use with DTS Wall mounted DMX controller 0514L007), M4CH

mode (5 DMX channels; Dimmer + RGBA), RGBA mode (4 channels), 1 DMX channel mode or

CUSTOM DMX mode (not yet implemented).

If you want to use the FOS 100 SOLO FULL RGBW or FULL WHITE CT in “WALL” mode, select

the “WALL” mode from the MODE menu and set the following addresses on the mixer: (To be

used only with DTS Wall mounted DMX controller 0514L007)

Projector 1 A001

Projector 2 A006

Projector 3 A012

….. A….

projector 6 A030

If you want to use the FOS 100 SOLO FULL RGBW or FULL WHITE CT in 10 channels mode,

select the 10 CH mode from the MODE menu and set the following addresses on the mixer:

FOS 100

12

If you want to select the next projector, just add “6”

DTS Wall mounted DMX controller 0514L007 assign 6 DMX

channels per unit also if some channels are not used

DISPLAY FUNCTIONS

The FOS 100 SOLO display panel shows all the available functions . Using these functions, it is

possible to change some of the parameters and add some functions. Changing the D.T.S. setting

can vary the functions of the unit so that it does not respond to the DMX 512 signal used to

control it. Carefully follow the instructions below before carrying out any variations or selections.

NOTE: the symbol shows which key has to be pushed to obtain the desired function.

Software version 5.03

FOS 100 SOLO FULL RGBW

FOS 100 SOLO FULL WHITE CT

FOS 100

13

DOWN

UP

ENTER

MENU

Up-DownMENU ENTER

DMX MODE

To select DMX mode : 10 DMX channels

mode (default), 6 DMX channels mode

(Shutter + Dimmer + RGBA), 15 DMX

channels mode, WALL mode (6 DMX

channels; for use with DTS Wall

mounted DMX controller 0514L007),

M4CH mode (5 DMX channels; Dimmer

+ RGBA), RGBA mode (4 channels), 1

DMX channel mode.

M4CH (5 CHANNELS)

Up-Down

ENTER

Up-Down

MENU

ENTERUp-Down

REVERSE DISPLAY

Reverses display's reading depending on

the mounting position

(On the ground or suspended).

Up-Down

Floor

position

Suspension

position

Up-DownENTER

DISPLAY STAND BY

To turn off the display (after 5 seconds)

or leave it always on.

Display OFF

Display

always ON

ENTER

Default DMX Mode = 10 CH

10 CHANNELS

Up-Down

Up-DownENTER

ENTER

Custom mode enabled

Show Custom settings

Parameters Setting on

Custom Mode

CUSTOM DMX mode let you set the

parameters for Shutter, Dimmer, Red,

Green, Blue, Amber, White, CTC, Macro

and Function to the desired DMX

channels.

AUX mode let you activate an external

ON-OFF control on IR connector.

(not implemented on FOS 100 SOLO)

15 CHANNELS

Up-Down

ENTER

WALL (6 CHANNELS)

Up-Down

ENTER

Up-Down

ENTER

6 CHANNELS

RGBA (4 CHANNELS)

Up-Down

ENTER

Shutter + Dimmer + RGBA

Dimmer + RGBA

1 CHANNEL

FOS 100

14

Up-Down

MENU

ENTERUp-Down

LED

RGBA Min/Max, Smooth, Compression,

Sync and Boost level values settings

Up-Down

Up-DownENTER

ENTER

Up-Down

Up-DownENTER

ENTER

RGBA MINIMUM VALUES

This menu allow to select the

minimum levels for Red, Green,

Blue and Amber

RGBA MAXIMUM VALUES

This menu allow to select the

maximum levels for Red, Green,

Blue and Amber

Default = 255

Default = 0

Default = 255

These settings have priority

on Master Dimmer channel

Up-Down

Up-DownENTER

ENTER

Range = Off-20

Default = 4

SMOOTH VALUE

This menu allow to select the value

of the delay (in milliseconds) for

RGBA and Dimmer channels

reaction to DMX or Program

variation.

Off=25 ms delay (Fast response)

20=250 ms delay (Slow response)

Off = 25 ms

Istant responce to DMX variation

20 = 250 ms

Smooth response to DMX variation

Up-Down

Up-DownENTER

ENTER

Linear = Linear

current output

COMPRESSION

This menu allow to select between

Linear current output or Quadratic

current output for LEDs

Default = Linear

Quadratic =

Linear light

output

ENTER

SYNC

This menu allow to adjust the PWM

frequency value (Hz) in order to

reduce flickering in the process of

your camera recordings

Up-Down

Up-DownENTER

Range = 610 Hz -10 KHz

Default = 610 Hz

ENTER

Boost mode activated

With BOOST active, the LED’s

current is set to 500 mA (30%

more gain).

Default = Disabled

Up-DownENTER

ENTER

BOOST DRIVING

This menu allow to increase the LED’s

current from 350 mA to 500 mA

Boost mode deactivated

Up-Down

ENTER

AUX MODE

External ON - OFF control on IR

connector (not implemented on

FOS 100 SOLO)

Up-Down

ENTER

MENU ENTER

Up-Down

Standard mode enabled:

(Default).

Extended mode enabled:

Rainbow effects on MACRO

channel.

ENTER

Up-Down

Up-DownENTER

ENTER

MACRO

MACRO Function, enable channel

mapping macro rainbow effects

STD (default)

Up-Down

Up-DownENTER

ENTER

Default = 0

Default = 255

15

FOS 100

Up-DownENTER ENTER

WHITE MACROS

16 macros for White color from

2800 to 6500 ° K

Up-DownENTER

ENTER

DIMMER

Dimmer level selectable by user

as on DMX channel 2 (Dimmer)

Dimmer level is active for all the

programs and macros

SHUTTER

Shutter level selectable by user

as on DMX channel 1 (Shutter)

Shutter level is active only for

CU01/CU16 and Wh01/Wh16

macros

ESC

Esc from Automatic Mode Menu

ENTER

MENU

Up-Down

Up-DownENTER ENTER

Up-Down

ENTER

AUTOMATIC MODE

Automatic demo game without

DMX controller

ChPr

Chase with 16 steps previously

created in REC MODE

Speed and Wait time selectable

by user

ENTER

Up-Down

CUPr

RGB values selectable by user

Rainbow (rAIn)

Rainbow colours effect.

Speed time selectable by user

ENTER

Up-Down

CU01-CU16

Color Macros as on DMX channel

8 (Macro)

Up-DownENTER ENTER

MENU

Up-Down

ENTER

REC MODE

In DMX Recorder Mode,it is

possible to create and store the

scenes of the ChPr by using an

external DMX controller.

The unit must be set to 10

channels MODE

FOS 100

16

Up-DownENTER

ENTER

MENU

Up-Down

ENTER

SLAVE MODE

Slave mode for ChPr program.

All slave units will be

synchronised with master unit,

running their own Chpr program.

Up-DownENTER

MENU

Up-Down

ENTER

INFRARED MODE

Infrared remote control.

By activating Ir MODE, it will be

possible to navigate trought the

unit functions by using the D.T.S.

infrared remote control.

D.T.S. Code :0514L008

NOTE:

External infrared remote sensor

needed.

D.T.S. Code :03.LA.016

NOT IMPLEMENTED ON FOS 100

EMERGENCY

Emergency operating mode.

By setting Emergency mode, it

will be possible to select one of

the 16 preprogrammed WHITE

cues that will then ran if DMX

signal is missing or not available.

Usefull for Emergency EXIT

ilumination on public areas.

Up-Down

MENU

Up-DownENTER

ENTER

Default = OFF

Default = White 1

Default = 255

ENTER

DMX Recorder Mode

For the programming of ChPr by using a DMX controller, besides the 10 channels necessary to control the unit a further 3

DMX channels are needed.

So that in RECORDER mode (via DMX) the unit will need 13 channels to be correctly programmed.

The three new DMX channels are:

DMX channel 11 = SCENES channel

From 0-10 = no function (r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016 )

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the

selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene has been

recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to

save the scene. If ChPr is not closed, by indicating the last scene ( Edit channel between 235-255), in playback mode all

16 scenes will be played through even if not programmed

Up-DownENTER

MENU

Up-Down

ENTER

FAN SPEED CONTROL

Internal Fan Speed control

selectable by user.

Range: OFF - 24 volt

Default : 12 volt

Fan Speed Control

Range: OFF - 24 volt

Default = 12 volt

Up-DownENTER

MENU

Up-Down

ENTER

WIRELESS DMX

Wireless DMX enabled/disabled.

Wireless DMX receiver kit on FOS

100 is available on request.

WIRELESS DMX Disabled

(Default)

WIRELESS DMX Enabled

Up-Down

ENTER

UNLINK = LOG OUT

ENTER

Up-DownENTER

LIFE TIME

This menu show the total UNIT life time

and the RGBA life time

Up-Down

MENU

ENTER

Up-Down

MENU

SOFTWARE

Software version

ENTER

TEST MODE

RGBA colours test with rainbow

Up-Down

MENU

FOS 100

17

.

ENTERENTER

Up-Down

MENU

DEFAULT

To restore default settings

Internal Unit temperature.

(° Celsius)

ENTERENTER

Up-Down

MENU

TEMPERATURE

Internal Unit temperature

visualisation

.

FOS 100

18

SERVICE MENU

For technical personnel only

To operate this menu:

-Connect the unit to the main

-While reset is running, press the MENU and ENTER keys at the same time.

EXIT

Exit from Service menu.

CHANNELS

This menu allow to set 3 channels or 4 channels LEDs output mode

3 CH = RGB mode

4 CH = RGBA mode (Default)

PRODUCT MODEL SELECTION:

TITAN = for TITAN PLUS and FOS 100 units (Default)

STRIP = only for FOS 100 POWER units

DELTA 8 = only for DELTA 8 units

POWER LIMITATION PARAMETER

Range: 0% - 100%

100% (Default)

AUTOMATIC OPERATION (AUTO):

FOS 100 SOLO can work in automatic mode without a DMX controller. First of all connect the projectors

with a DMX cable (picture below). A maximum quantity of 32 slave units can be connected to the same

Master unit.

To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO

appears on the display, and press enter.

Now it is possible to choose between the different pre-programmed games (CUPr-RAIn-CU01/CU16-

Wh01/Wh16) or ChPr which is user programmable through REC mode. To confirm game activation press

ENTER on the selected GAME.

CUPr-RAIn-CU01/CU16-Wh01/Wh16

The first unit that will work as a Master should be placed in Automatic mode (AUTO), the other units

have to be placed in 10 DMX channels mode (MODE 10CH) and the DMX address should be set at A001.

For RaIn (rainbow) game it is possible to select the speed for the colour changhing (SPEE).

DIMMER function (in AUTOMATIC MODE) is active for all the programs.

SHUTTER function (in AUTOMATIC MODE) is active only for CU01/CU16 and Wh01/Wh16 macros.

ChPr MASTER/SLAVE

The first unit that will function as a Master must be set to Automatic mode (AUTO), the other units must

be set to Slave mode (SLAV), selectable through the menu. In this way all the Slave units will be

synchronised with the master and running their own ChPr game.

On the master unit it is possible to vary the Speed time (SPEE) for the colour changhing and the Wait

time (UAIt) between the steps.

Speed time and Wait time on the Master, have priority on the slave units.

NB: It is possible to run GA.Pr on the other units even though these do not have GA.Pr programmed.

You can do this by setting the units to 10 DMX channels mode and selecting DMX address A001.

MASTER SLAVE 1

SLAVE 2

SLAVE 32

FOS 100

19

Rec mode

It is possible to program your own game on the FOS 100 SOLO FULL RGBW / FOS 100 SOLO FULL

WHITE CT that will then run it in AUTO mode (ChPr).

Each unit can have its own programmed game.

In REC mode the unit must be set to 10 DMX channels mode.

To program the ChPr by using a DMX controller, you need 3 more channels in addition to the 10 channels

necessary to control the unit.

So that in RECORDER mode (via DMX) the unit will need 12/13 DMX channels to be correctly

programmed.

The three new DMX channels are:

DMX channel 11 = SCENES channel

From 0-10 = no function (r001)

From 11-255 are displayed the programmable scenes (max 16 scenes from M001 to M0016)

DMX channel 12 = EDIT channel:

-From 0-19 = no function

-From 20-234 the unit runs the configuration given by the received input DMX values.

With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to

record the selected scene.

-From 235-255 the unit runs the configuration given by the received input DMX values closing the

sequence as last scene.

With the channel REC it is possible to record the selected scene as last scene.

DMX channel 13 = RECORDING channel

Records the set scene with a variation between 0 to 255 (the display flashes indicating that the scene

has been recorded).It is advised that you keep the REC channel set to 0 and to run through the 255 only

once you have decided to save the scene. If ChPr is not closed, by indicating the last scene (Edit channel

between 235-255), in playback mode all 16 scenes will be played through even if not programmed.

FOS 100

20

La pagina sta caricando ...

DTS FOS 100 FULL RGBW Manuale utente

Questo manuale è adatto anche per

DTS FOS 100 FULL RGBW Manuale utente

in altre lingue

Documenti correlati

Altri documenti