ProLights 240W moving spot Manuale utente

Categoria
Proiettori
Tipo
Manuale utente
USER MANUAL
MANUALE UTENTE
JETSPOT3
MOVING HEAD
EN - ITEN - IT
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals section on site www.musiclights.it
REV.003-11/18
1
JETSPOT3
Packing content
JETSPOT3
Mount bracket
User manual
TABLE OF CONTENTS
Safety
General instructionsGeneral instructions
Warnings and installation precautionsWarnings and installation precautions
1 Introduction
1. 1 Description 1. 1 Description
1. 2 Technical specications1. 2 Technical specications
1. 3 Operating elements and connections1. 3 Operating elements and connections
2 Installation
2. 1 Mounting2. 1 Mounting
3 Functions and settings
3. 1 Operation3. 1 Operation
3. 2 Basic3. 2 Basic
3. 3 Using the menu3. 3 Using the menu
3. 4 Menu structure3. 4 Menu structure
3. 5 Linking3. 5 Linking
3. 6 DMX address3. 6 DMX address
3. 7 DMX mode3. 7 DMX mode
3. 8 DMX addressing 3. 8 DMX addressing
3. 9 Fixture settings3. 9 Fixture settings
3. 10 Advanced 3. 10 Advanced
3. 11 Fixture information3. 11 Fixture information
3. 12 Operation in automatic mode 3. 12 Operation in automatic mode
3. 13 Automatic mode speed3. 13 Automatic mode speed
3. 14 Connection of the DMX line 3. 14 Connection of the DMX line
3. 15 Construction of the DMX termination 3. 15 Construction of the DMX termination
3. 16 DMX control3. 16 DMX control
3. 17 Colors and gobos3. 17 Colors and gobos
4 Maintenance
4. 1 Maintenance and cleaning the unit4. 1 Maintenance and cleaning the unit
4. 2 Fuse replacement4. 2 Fuse replacement
4. 3 Trouble shooting4. 3 Trouble shooting
2
2
3
3
5
6
7
7
8
8
10
10
10
10
11
13
13
14
14
15
15
16
20
21
21
22
JETSPOT3
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
The products referred to in this manual conform to the European Community Directives and are there-
fore marked with
.
The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
This unit is not for home use, only professional applications.
Never use the xture under the following conditions:
- in places wet;
- in places subject to vibrations or bumps;
- in places with an ambient temperature of over 45°C.
Make certain that no inammable liquids, water or metal objects enter the xture.
Do not dismantle or modify the xture.
All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
Always additionally secure the projector with the safety rope. When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the xture’s being used.
For inside use only. Not designed for outside use.
The minimum distance between the xture and surrounding walls must be more than 50 cm and the
air vents at the housing must not be covered in any case.
Install the xture in a well ventilated place.
Keep any inammable material at a safe distance from the xture.
The maximum temperature that can be reached on the external surface of the tting, in a thermally
steady state, is high. After power o, please cool down over 15 minutes.
Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally deformed.
Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
This product was designed and built strictly for the use indicated in this documentation. Any other use,
not expressly indicated here, could compromise the good condition/operation of the product and/or
be a source of danger.
We decline any liability deriving from improper use of the product.
3
JETSPOT3
- 1 - INTRODUCTION
1.1 DESCRIPTION
JETSPOT3 is a LED spot luminaire designed to deliver a stunning light level for its size and price. Ideal both
for installation and for rental, the JETSPOT3 focusses on maximising the light output from its LED source
to deliver a crisp, even beam from a compact size.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
Source: 240W high-power white LED
CT: 7.500K
CRI: 78
Luminous ux: 12’459lm
Lux: 13’389lx @3 m
Lux: 1’205lx @10 m
Source life expectancy: >30.000 h
OPTICS
Beam angle: 20°
Lens diameter: 74mm
Lens type: high-quality glass lens optics
Focus: motorised
COLOUR SYSTEM
Colour wheel: 7 dichroic lters + open on 2 independent colour wheels (7 + 7)
DYNAMIC EFFECTS
Rotating gobos: 7 rotating gobos + open, interchangeable, indexing
Gobo size: outer: 27,8 mm - image: 23 mm - thickness: 3 mm
Fixed gobos: 8 xed gobos + open, interchangeable
Gobo size: outer: 29,6 mm - image: 23,8 mm - thickness: 0,5 mm
Circular prism: 3f with bi-directional rotation, indexing
Frost: linear 0 - 100% frost lter
Iris: 5 ~ 100% motorised linear iris
Auto mode: built-in programs with execution speed adjustment
BODY
Pan angle: 540°
Tilt angle: 260°
Pan/Tilt resolution: 16 bit
Feedback: automatic repositioning after accidental movement
Body: aluminium structure with hi-resistance polycarbonate cover
Body colour: black, white nishing available
CONTROL
Protocols: DMX512, RDM
DMX channels: 17 / 19channel
RDM: RDM ready for xture remote monitor and settings
JETSPOT3
4
Display: black OLED high resolution display
Firmware upgrade: yes, via USB - DMX interface (UPBOX1) not included
Master/Slave: for synchronized operation of more units linked in a chain
ELECTRONICS
Dimmer: linear 0 ~ 100% electronic dimmer
Strobe / shutter: 0 ~ 30 Hz, electronic
Battery backup: battery backup for user operation without connecting to the main power
Operating temperature: -10° ~ +45°
Flicker: icker free operation
ELECTRICAL
Power supply: 100-240 V – 50/60 Hz
Power consumption (at 230V): 316W
Power consumption (at 120V): 322W
Output (at 230V): 12 units on a single power line
Output (at 120V): 6 units on a single power line
PHYSICAL
Cooling: forced air with low noise fan
Sospension and xing: any position with quick-lock omega brackets
Signal connection: Amphenol XLR 3p + 5p IN/OUT connectors
Power connection: Neutrik powerCON IN/OUT connectors
IP rating: 20
Dimensions (WxHxD): 355x500x257mm
Weight: 17,3kg
Fig.1
500
344
257
Technical drawing
5
JETSPOT3
Fig.2
1
2
A
B
3
4
7
8
5
6
10
119
1.3 OPERATING ELEMENTS AND CONNECTIONS
1. MOVING HEAD
2. ROTARY ARM
3. CONTROL PANEL with TFT display
and 4 button used to access
the control panel functions and
manage them.
4. LED INDICATOR
5. DMX IN (3-pole XLR): 1 = ground, 2
= DMX -, 3 = DMX +
6. DMX OUT ( 3-pole XLR): 1 =
ground, 2 = DMX -, 3 = DMX +
7. DMX IN (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
8. DMX OUT (5-pole XLR):
1 = ground, 2 = DMX-, 3 = DMX+,
4 N/C, 5 N/C
9. MAIN FUSE HOLDER: replace a
burnt-out fuse by one of the same
type only.
10. POWER IN (PowerCON IN):
for connection to a socket
(100-240V~/50-60Hz) via the
supplied mains cable.
11. POWER OUT: (PowerCON OUT) to
connect multiple units in series.
View A
View B
JETSPOT3
6
- 2 - INSTALLATION
2.1 MOUNTING
The JETSPOT3 may be set up on a solid and even surface. By means of the xing facilities of the baseplate,
the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For xing, stable
mounting clips are required. According to the gure, the bolts of the brackets are placed into the openings
provided in the base plate and turned clockwise until they lock (to the stop). Always ensure that the unit
is rmly xed to avoid vibration and slipping while operating. The mounting place must be of sucient
stability and be able to support a weight of 10 times of the units weight. When carrying out any installa-
tion, always comply scrupulously with all the regulations (particularly regarding safety) currently in force
in the country in which the xtures being used. Always additionally secure the projector with the safety
rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the maximum
fall of the projector will be 20 cm.
CLAMP
SAFETY
CABLE
Fig.3
OMEGA
BRACKETS
7
JETSPOT3
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to
reset all motors to their home position. Shortly after that the JETSPOT3 is ready for operation. To switch
o, disconnect the mains plug from the socket. For a more convenient operation it is recommended to
connect the unit to a socket which can be switched on and o via light switch.
3.2 BASIC
The control panel of JETSPOT3 has a display and 4 buttons for the complete programming and manage-
ment of the projector menu (g.4).
Fig.4 - Functions of the buttons
UP DOWN MENU ENTER
Increases the value
displayed or passes to
the previous item in a
menu
Decreases the value
displayed or passes to
the next item in the
menu
To enter in the main
menù or to return to the
top level
Conrms the displayed
value, or activates the
displayed function, or
enters the successive
menu
Reversal of the display
To activate this function, hold simultaneously for 3 seconds UP and DOWN buttons while the display
is in the rest mode. This status will be memorised and maintained even for the next time it will be
switched on.
To return to the initial state, repeat the operation all over again.
JETSPOT3
8
3.3 USING THE MENU
1. Press the ENTER button to access the main menu.
2. Use the UP/DOWN button to select the menu to be used:
Connect;
Setup;
Advanced;
Information;
Stand alone;
3. Press ENTER to display the rst item in the selected menu.
4. Use the UP/DOWN button to select the menu items.
NOTE - The display can be in one of two conditions: rest status and setting status. When it is in the rest sta-
tus, the display shows the projectors DMX address. During menu setting status, after a wait time without
any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modied but not yet
conrmed with the ENTER button will be cancelled.
3.4 MENU STRUCTURE
MENU
1 CONNECT
ð
DMX Address
ð
Value (1-512)
DMX Mode
ð
Standard - 17CH
Extended - 19CH
2 SET UP
ð
Movement
ð
Pan Reverse
ð
YES/NO
Tilt Reverse
ð
YES/NO
Pan Feedback
ð
YES/NO
Tilt Feedback
ð
YES/NO
Screen
ð
Backlight
ð
ON
10s
20s
30s
Flip Display
ð
YES/NO
Warn Cue
ð
ON/OFF
Key Lock
ð
YES/NO
Fixture
ð
Fan mode
ð
Atuo/High
Temperature unit
ð
C°/F°
Auto Test
ð
Auto Test
Manual Test
ð
Pan
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
Dimmer
Shutter
Color1
Color2
ð
Value (000-255) for each function
9
JETSPOT3
Gobo1
R-Gobo1
Gobo2
Prism Rot
Focus
Frost
Iris
ð
Value (000-255) for each function
3 ADVANCED
ð
Reset
ð
All
ð
YES/NO
Pan
Tilt
Color1
Color2
Gobo1
Gobo2
Prism
Focus
Frost
Iris
Adjust
ð
Pan Oset
ð
Value (000-255) for each function
Tilt Oset
Color1 Oset
Color2 Oset
Gobo1 Oset
R-Gobo1 Oset
Gobo2 Oset
Prism Oset
Focus Oset
Frost Oset
Iris Oset
Factory Reload
ð
YES/NO
4 INFORMATION
ð
Fixture Time
Temperature
Fans Speed
Software Ver.
UID
5
STAND ALONE
ð
Play
ð
Master/Slave
ð
Master
Slave
Sequence
ð
Show 1
Show 2
Show 3
Show 4
JETSPOT3
10
3.5 LINKING
Several units may be interconnected in order to control all further slave units to the same eect of the
master unit.
1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.
2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units
are connected in a chain.
3.6 DMX ADDRESS
To enter the DMX mode, follow these steps:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.
Press the arrow keys to select the desired value (001-512).
Press the ENTER key to conrm the setting.
Press the MENU button repeatedly to exit the menu and save changes.
3.7 DMX MODE
The JETSPOT3 has more DMX channel congurations which can be accessed from the control panel.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, select the mode and press ENTER to conrm
your choice.
Press the MENU button repeatedly to exit the menu and save changes.
The unit is equipped with 3/5-pole XLR connections.
3.8 DMX ADDRESSING
For operation via light control unit with DMX512 protocol, is sucient connect the controller to JETSPOT3.
To able to operate the JETSPOT3 with a light controller, adjust the DMX start address for the rst a DMX
channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX chan-
nel, adjust the start address 33 on the JETSPOT3. The other functions of the light eect panel are then
automatically assigned to the following addresses.
An example with the start address 33 is shown below:
Speed
ð
Value (000-100%)
Number of
DMX channels
Start address
(example)
DMX Address
occupied
Next possible start
address for unit No. 1
Next possible start
address for unit No. 2
Next possible start
address for unit No. 3
19 33 33-52 53 72 91
21 33 33-54 55 76 97
11
JETSPOT3
3.9 FIXTURE SETTINGS
You can change the parameters for the device by following these steps:
MOVEMENT
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Set Up icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select Movement and press the ENTER but-
ton to enter the next menu.
Use the UP/DOWN button to select the option proposed and press the ENTER button to conrm the
setting.
- Pan Reverse - Pan rotation in the opposite direction. Select NO to deactivate the function (normal set-
ting); YES to activate the function (Pan Reverse).
- Tilt Reverse - Used for reversing tilt movement. Select NO to deactivate the function (normal setting);
YES to activate the function (Tilt Reverse).
- Pan/Tilt Feedbacks - Reorganization Pan/Tilt position after rolling away. Select NO to deactivate or YES
to activate the function.
Press the ENTER button to conrm your choice.
Press the MENU button repeatedly to exit the menu and save changes.
SCREEN
You can change the following parameters related to the display, following the same procedure:
Press the ENTER button to access the main menu.
Press the UP / DOWN keys to scroll the menu, select the Set Up icon, then press the ENTER button to
enter the next menu.
Press UP / DOWN to scroll through the menu, then select Screen, and press the ENTER button to enter
the next menu.
Fig.6 - Example 21 DMX channels conguration
DMX Address: 96DMX Address: 54DMX Address: 33 DMX Address: 75
. . . . . . . . . . . .
DMX512 Controller
JETSPOT3
12
Press UP / DOWN to scroll through the menu, and then select one of the following settings for the dis-
play and press the ENTER key to display it.
- Back Light - Backlight display Auto O. This feature allows you to automatically turn o the backlight
after a specied time that you can set using the arrow buttons. To have the display always on select
Always On or choose another value to turn o the display after the amount of time you choose.
- Flip Display - Orientation of the display. This function allows you to rotate the display 180° to get a
better view of the display when the unit is hanging upside down. Select YES to activate or NO to dis-
able this function.
- Key Lock - Lock keys. With this function, you can lock the buttons on the control panel. If this function
is activated, the keys are automatically locked. To disable or temporarily disable the key lock func-
tion, press the buttons in the following order to regain access to menu commands: UP, DOWN, UP,
DOWN, RIGHT. Select YES to activate or NO to disable.
Press the ENTER button to conrm your choice.
Press the LEFT button repeatedly to exit the menu and save changes.
FIXTURE
Fans Mode - Select this function to set the fans operation mode:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select UI Set, and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, and then select Fans Mode and press ENTER
to conrm.
Press the UP/DOWN button to select Auto Speed/High Speed, press the ENTER button to conrm your
choice.
Press the MENU button repeatedly to exit the menu and save changes
Temperature - Select this function to set the temperature unit measurement shown on the display:
Press the ENTER button to access the main menu.
Press the UP/DOWN to scroll through the menu, select the Set icon, then press the ENTER button to
enter the next menu.
Press the UP/DOWN to scroll through the menu, select UI Set, and press the ENTER button to enter the
next menu.
Press the UP/DOWN button to scroll through the menu, select Temperature C/F and press ENTER to
conrm.
Press the UP/DOWN button to select the unit of measure Celsius/Fahrenheit and press the ENTER but-
ton
to conrm your choice.
Press the MENU button repeatedly to exit the menu and save changes.
Auto and Manual test: with this menu, you can test all functions; with auto the moving head will start an auto
test, with manual you can choose each channel/function to test.
3.10 ADVANCED
Reset Functions
You can start a preset program to restore the selected function:
Press the ENTER button to access the main menu.
13
JETSPOT3
Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Reset and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select the function you wish to reset be-
tween All, Pan, Tilt, Color1, Color2, Gobo1, Gobo2, Prism, Focus, Frost, Iris.
Press the ENTER button to conrm your choice and wait for the recovery of the selected function.
Adjust
Adjusts the lamp. This function allows you to modify all the parameters of the lamp: Pan Oset, Tilt Oset,
Color1 Oset, Color2 Oset, Gobo1 Oset, R-Gobo1 Oset, Gobo2 Oset, Prism Oset, Focus Oset, Frost Oset, Iris Oset.
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Adjust and press the ENTER button to
enter the next menu.
Press the UP/DOWN button to select one of the parameters and press ENTER to edit the value (000-255)
through the UP/DOWN button.
Press the ENTER button to conrm your choice and then press the MENU button repeatedly to exit the
menu and save changes.
Factory Reload
Select this function to reset the unit to factory settings:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Advanced icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Factory Reload and press the ENTER button
to enter the next menu.
Press the UP/DOWN button to select YES or NO, then press the ENTER button to conrm.
3.11 FIXTURE INFORMATION
To view all the information on the device, proceed as follows:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the icon Information, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, then select one of the following information
and press the ENTER button to display it.
- Fixture Time - Through the Fixture Time function you can display the operating time of the projector.
- Temperature - Through the Temperature function can be displayed the temperature inside the xture,
near the lamp. The temperature can be displayed in degrees Celsius or Fahrenheit.
- Fans Speed - Through the Fans Speed function you can show on display the fan speed present near the
lamp. Velocity is expressed in RPM (revolutions per minute).
- Software Version - Through Software Version function you can display the currently installed software
version.
- UID - This option shows the RDM identication number.
Press the MENU button repeatedly to exit the menu.
RDM - With this function you can call up various submenus via RDM. This device is RDM ready. RDM stands
for “Remote Device Management” and makes remote control of devices connected to the DMX-bus possible.
JETSPOT3
14
Manual settings like adjusting the DMX starting address are no longer needed. RDM is integrated in DMX
without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1 and 2 so new
DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated in one DMX line.
If DMX splitters are used and RDM control is to be used, these splitters must support RDM.
3.12 OPERATIONS IN AUTOMATIC MODE
The unit independently runs through its show. Before you send an automatic program you need to set the
drive as Master/Alone:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, select Sequence and press ENTER to conrm
your choice.
Press the UP/DOWN button to select the mode of operation:
- Master, if the unit is connected in series with other units and it acts as the Master;
- Slave, if the unit is connected in series with other units and it acts as the Slave;
Press the ENTER button to conrm your choice.
Press the MENU button repeatedly to exit the menu and save changes.
The unit will go into automatic mode by executing the program automatically.
3.13 AUTOMATIC MODE SPEED
Select this function to set the value of the speed of the internal auto-shows:
Press the ENTER button to access the main menu.
Press the UP/DOWN button to scroll the menu, select the Stand Alone icon, then press the ENTER button
to enter the next menu.
Press the UP/DOWN button to scroll through the menu, select Play, and press the ENTER button to enter
the next menu.
Press the UP/DOWN button to scroll through the menu, then select Speed. and press ENTER to conrm.
Press the UP/DOWN button to adjust the speed, and then press the ENTER button to conrm your
choice.
Press the MENU button repeatedly to exit the menu and save changes.
15
JETSPOT3
Fig.7
Fig.8
3.14 CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-
ance and low capacity.
The following diagram shows the connection mode:
ATTENTION
The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would
cause faulty xture and controller operation.
Over long runs can be necessary to insert a DMX level matching amplier.
For those connections the use of balanced microphone cable is not recommended because it cannot
transmit control DMX data reliably.
Connect the controller DMX input to the DMX output of the rst unit.
Connect the DMX output to the DMX input of the following unit. Connect again the output to the input
of the following unit until all the units are connected in chain.
When the signal cable has to run longer distance is recommended to insert a DMX termination on the
last unit.
3.15 CONSTRUCTION OF THE DMX TERMINATION
The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-
es the end of the line: under certain conditions and with certain cable lengths, this could cause them to
cancel the original signals.
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR
connector, as shown in gure.
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
Pin1 : GND - Shield
Pin2 : - Negative
Pin3 : + Positive
Pin4 : N/C
Pin5 : N/C
Example:
3 pin XLR connector
JETSPOT3
16
3.16 DMX CONTROL
STANDARD EXTENDED
FUNCTION
DMX
Value
17 ch 19 ch
1 1 PAN 8 bit 000 - 255
2 2 PAN 16 bit 000 - 255
3 3 TILT8 bit 000 - 255
4 4 TILT 16 bit 000 - 255
5 5
MOVEMENT SPEED
Fastest to slowest 000 - 255
6 6
SHUTTER
Shutter closed
No function (shutter open)
Strobe eect slow to fast
No function (shutter open)
Pulse-eect in sequences
No function (shutter open)
Random strobe eect slow to fast
No function (shutter open)
000 - 031
032 - 063
064 - 095
096 - 127
128 - 159
160 - 191
192 - 223
224 - 255
7 7
DIMMER
Dimmer (close to open) 000 - 255
8 8
COLOR WHEEL 1
Selection
Open
Open+DARK RED
DARK RED
DARK RED + DARK BLUE
DARK BLUE
DARK BLUE + YELLOW
YELLOW
YELLOW + GREEN
GREEN
GREEN + LIGHT ORANGE
LIGHT ORANGE
LIGHT ORANGE + MAGENTA
MAGENTA
MAGENTA + UV
UV
UV+Open
Forward Spin
Stop to fast
Reverse Spin
Fast to Stop
Continuous
Positioning from OPEN to OPEN
000 - 003
004 - 007
008 - 011
012 - 015
016 - 019
020 - 023
024 - 027
028 - 031
032 - 035
036 - 039
040 - 043
044 - 047
048 - 051
052 - 055
056 - 059
060 - 063
064 - 095
096 - 127
128 - 255
9 9
COLOR WHEEL 2
Selection
Open
Open+CTO
CTO
000 - 003
004 - 007
008 - 011
17
JETSPOT3
STANDARD EXTENDED
FUNCTION
DMX
Value
17 ch 19 ch
9 9
CTO + JADE
JADE
JADE + CTB
CTB
CTB + PINK
PINK
PINK + LIGHT GREEN
LIGHT GREEN
LIGHT GREEN + DARK ORANGE
DARK ORANGE
DARK ORANGE + CYAN
CYAN
CYAN+Open
Forward Spin
Stop to fast
Reverse Spin
Fast to Stop
Continuous
Positioning from OPEN to OPEN
012 - 015
016 - 019
020 - 023
024 - 027
028 - 031
032 - 035
036 - 039
040 - 043
044 - 047
048 - 051
052 - 055
056 - 059
060 - 063
064 - 095
096 - 127
128 - 255
10
ROTATING GOBO MODE
Indexed
Forward Spin
Reverse Spin
Continuous
Shake (speed on each gobo)
TBD
000 - 015
032 - 047
048 - 063
064 - 079
080 - 095
096 - 255
11
ROTATING GOBO SELECTION
Index & Shake (shake from slow to fast)
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Forward Spin
Stop to fast
Reverse Spin
Fast to stop
Continuous
Positioning from OPEN to CYAN
000 - 031
032 - 063
064 - 095
096 - 127
128 - 159
160 - 191
192 - 223
224 - 255
000 - 255
000 - 255
000 - 255
10
ROTATING GOBO WHEEL
Indexed
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
000 - 005
006 - 010
011 - 015
016 - 020
021 - 025
JETSPOT3
18
STANDARD EXTENDED
FUNCTION
DMX
Value
17 ch 19 ch
10
Gobo 5
Gobo 6
Gobo 7
Shake
Gobo 1 (shake from slow to fast)
Gobo 2 (shake from slow to fast)
Gobo 3 (shake from slow to fast)
Gobo 4 (shake from slow to fast)
Gobo 5 (shake from slow to fast)
Gobo 6 (shake from slow to fast)
Gobo 7 (shake from slow to fast)
Forward Spin
Stop to fast
Reverse Spin
Stop to fast
026 - 030
031 - 035
036 - 040
041 - 055
056 - 070
071 - 085
086 - 100
101 - 115
116 - 130
131 - 145
146 - 200
201 - 255
11 12
GOBO ROTATION
Indexing
Gobo 1 (index rotation from 0° to 360°)
Forward Spin
Stop to fast
Stop
Reverse Spin
Fast to stop
000 - 191
192 - 221
222 - 225
226 - 255
12 13
FIXED GOBOS
Selection
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Shake
Gobo 1 (shake from slow to fast)
Gobo 2 (shake from slow to fast)
Gobo 3 (shake from slow to fast)
Gobo 4 (shake from slow to fast)
Gobo 5 (shake from slow to fast)
Gobo 6 (shake from slow to fast)
Gobo 7 (shake from slow to fast)
Gobo 8 (shake from slow to fast)
Forward Spin
Slow to fast
Reverse Spin
Fast to slow
000 - 005
006 - 009
010 - 013
014 - 017
018 - 021
022 - 025
026 - 029
030 - 033
034 - 037
038 - 051
052 - 065
066 - 079
080 - 093
094 - 107
108 - 121
122 - 135
136 - 149
150 - 202
203 - 255
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

ProLights 240W moving spot Manuale utente

Categoria
Proiettori
Tipo
Manuale utente

in altre lingue