Dascom DL-820 Guida utente

User Guide DL-820 Thermal Desktop Label Printer

Tally Dascom DL-820 User Guide V1.0

I

Important Safety Instructions (English)

Read the following instructions thoroughly before starting up your printer.

 Never carry out maintenance or repair work yourself. Always contact a qualified service

technician.

 Keep this Operator’s Manual in a place which is easily accessible at all times.



Place the printer on a solid and even base so that it cannot fall.

 Never place the printer in the vicinity of inflammable gas or explosive substances.



Ensure the printer is connected to a socket with the correct mains voltage.

 Always disconnect the printer from the mains before opening the device to perform maintenance

work or remedy errors.

 Do not expose the printer to high temperatures, direct sunlight or dust.

 Keep all liquids away from the printer.

 Protect the printer from shock, impact and vibration.

 Make sure that the printer and computer are switched off before connecting the data cable.

 The print head will become very hot during printing; avoid contact with the print head after printing

has finished.

 Do not perform any operation or action in any way other than those provided in this manual.

When in doubt, contact your dealer or your customer support.

The device and mains-socket must all times be easily accessible.

Tally Dascom DL-820 User Guide V1.0

II

Wichtige Sicherheitshinweise (German)

Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen.



Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie

immer einen qualifizierten Servicetechniker.

 Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.



Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen

kann.

 Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven

Stoffen auf.

 Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.



Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den

Netzstecker an der Steckdose ziehen.



Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.



Keine Flüssigkeiten mit dem Drucker in Berührung bringen.



Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.

 Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel

angeschlossen wird.



Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen

lassen.



Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation

ab.

Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.

 Maschinenlärminformations – Verordnung – 3.GPSGV, der höchste Schalldruckpegel beträgt 70

dB(A) oder weniger gemäß EN ISO 7779.

Das Gerät und die Netzsteckdose müssen jeder Zeit leicht zugänglich sein.

Tally Dascom DL-820 User Guide V1.0

III

Consignes importantes de sécurité (French)

Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.

 Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un

dépanneur qualifié.

 Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.



Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de

substances explosives.

 Ne connecter l’imprimante à une prise que lorsque la tension est correcte.

 Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et

toujours débrancher le connecteur secteur de la prise murale.

 Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la

poussière.

 Ne pas mettre l’imprimante en contact avec des liquides.



Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.

 S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de

données.

 La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir quelques

instants avant d’y toucher.



N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel. En

cas de doute, veuillez contacter votre distributeur ou service après-vente.

Le dispositif et la prise principale doivent toujours être accessibles facilement.

Tally Dascom DL-820 User Guide V1.0

IV

Indicazioni di sicurezza importanti (Italian)

Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.

 Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un

tecnico

di assistenza qualificato.

 Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.

 Collocare la stampante su una superficie stabile, per evitare che cada a terra.

 Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.



Collegare la stampante a una presa di corrente con tensione adeguata.



Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire

sempre il connettore di rete dalla presa.

 Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.

 Evitare il contatto della stampante con liquidi.



Non esporre la stampante a colpi, scosse o vibrazioni.



Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione

dati.

 Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario

opportuno quindi lasciarla raffreddare qualche istante.

 Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale. In

caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.

Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili.

Tally Dascom DL-820 User Guide V1.0

V

Instrucciones de seguridad importantes (Spanish)

Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.

 Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico

de

servicio calificado.

 Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.

 Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.

 Nunca coloque la impresora en la vecindad de gases de fácil inflamabilidad o sunstancias

explosivas.

 Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.

 Cuando quiera desconectar la impresora de la red, apague la impresora y siempre tire la clavija de

alimentación del enchufe.



No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.



No ponga la impresora en contacto con fluidos.

 Nunca exponga la impresora a sacudidas, choques o vibraciones.



Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de datos.



La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, deje enfriarlo

algún tiempo antes de tocarla.

 No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala

en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio

post-venta.

El dispositivo y la toma de corriente deben estar ubicados de forma que sea fácil acceder a ellos.

Tally Dascom DL-820 User Guide V1.0

VI

Правила по технике безопасности. (Russian)

Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу

принтера.

 Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о

неисправностях квалифицированным сервисным техникам.



Данная инструкция должна быть всегда доступна каждому пользователю.

 Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.

 Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых

веществ.



Включайте принтер в розетку только с соответствующим напряжением.



Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем

выньте штекер из розетки.

 Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.

 Не допускайте попадания жидкости на принтер.



Нельзя подвергать принтер тряске, ударам и вибрации.



Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с

компьютером.

 Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то

время, прежде чем дотронуться до нее.



Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают

неясности, обращайтесь с вопросами к Вашим продавцам или в сервисный центр.

Устройство и розетка должны быть всегда легко доступна.

Tally Dascom DL-820 User Guide V1.0

VII

Instruções Importantes sobre Segurança (Portuguese)

Leia as instruções de segurança antes de usar a impressora.

 Consulte sempre um técnico qualificado para executar uma reparação .

 Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.



Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou

substâncias explosivas.

 Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.

 Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.

 Não exponha a impressora a temperaturas altas ou luz solar direta.



Não aproxime substâncias líquidas da impressora.



Proteja a impressora de choques, impactos e vibrações.

 Desligue a impressora e o computador antes de conectar o cabo da rede.

 A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de tocá-la.



Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de

dúvida, contate seu revendedor ou companhia de serviço.

A impressora e a tomada devem ser facilmente em todos os momentos acessíveis.

Tally Dascom DL-820 User Guide V1.0

VIII

Önemli

Güvenlik Talimatları (Turkish)

Lütfen,

yazıcıyı

i

ş

letim

e

geçirmeden

önce bu

güvenlik talimatlarını bütünüyle

dikkatleokuyun.



Ba

k

ı

m

ve

tamir çalışmalarını kesinlikle

ve

hiçbir

surette kendi

başınıza yapmayın; her

zamankalifiye

bir

uzmanse

r

v

i

s

-teknisyenin

e

haber verin.



Yazıcıyı, üzerinden

yere düşmesi

mümkün olmayacak

sabitve düz birzemineyerleştirin.



Yazıcıyı kesinlikle

ve

hiçbir

surette

kolayca yanabilecek

gaz veya

patlayıcı maddeler içeren

nesnelerin

yakınına koymayın.



Yazıcıakım

kablosunu

sadece

doğru gerilime

sahipbirprizetakın.



Yazıcıyı

şebeke

ağından ayırmak

is

te

d

i

ğ

i

n

i

z

de,

yazıcıyı kapatın

ve

ağ-fişini

her zaman

prizden

çıkartın.



Yazıcıyı

ne yüksek

ısılı

ne de

doğrudan

güneş

ışığına

ve toza

mâruz

kalan

mekânlarda bulundurun.



Yazıcı

hiçbir sıvı maddeyle

temasta

olmamalıdır.



Yazıcı hiçbir sarsıntıya, darbeye

veyat

i

tre

ş

ime

mâruz

kalmamalıdır.



Veri kablosu bağlanmadan

önce hem

yazıcının

hem de

bilgisayarın

kapalı

olduklarından

emin

olmalısınız.



Yazıcının başı

basma

esnasında

yüksek

ısıya ulaşıyor.

Bu yüzdenlütfen

dokunmadan

önce kısa süre

soğumasını

bekleyin.



Yazıcının işletimi

ve

kullanımında

bu

dokümantasyondaki talimatların

hiç

dışına çıkmayın.

Sorunlu

görünen hususlarda

lütfen

imâlatçınıza

veya

müşteri hizmetleri se

r

v

i

s

iniz

e başvurun.

Cihaz ve elektrik prizinin her zaman kolayca erişilebilir olması gerekir.

Tally Dascom DL-820 User Guide V1.0

IX

TRADEMARK ACKNOWLEDGEMENTS

“IBM” is a trademark of International Business Machines Corporation.

“EPSON” is a trademark of Epson America Incorporated.

“DEC” is a trademark of Digital Equipment Corporation.

“Centronics” is a trademark of Centronics Data Computer Corporation.

“DOS” is a trademark of Microsoft Corporation.

“SAP” is a trademark of SAP AG.

“Windows”, “Windows 7”,”Windows 8”, “Windows 10” , “Windows 95”, “Windows 98“, “Windows NT”,

“Windows 2000”, “Windows 2003/2008/2013 Server”, “Windows XP” and “Windows Vista” are trademarks

of Microsoft Corporation.

All other product names and company names appearing in this manual are the registered trademarks or

trademarks of the individual companies.

Tally Dascom DL-820 User Guide V1.0

Contents

CHAPTER 1 INTRODUCTION......................................................................................................................... 1

1.1 Features

......................................................................................................................................................

1

1.2 Specifications

.............................................................................................................................................

2

1.3 Consumables

.............................................................................................................................................

3

1.4 Size and Weight

........................................................................................................................................

4

1.5 Unpack and Inspect

..................................................................................................................................

5

1.6 Standard/optional components for the product

...................................................................................

7

1.7 Key components

..........................................................................................................................

8

1.8 Control Panel

........................................................................................................................

13

1.8.1 Normal/Setup modes operation

....................................................................................................

13

1.8.2 Four major setup menus

................................................................................................................

14

1.8.3 Sample for setup steps

...................................................................................................................

14

1.9 Displayed error messages

.....................................................................................................................

15

CHAPTER 2 INSTALLATION.........................................................................................................................16

2.1 Recommended installation procedures

...............................................................................................

16

2.2 Suitable installation site

........................................................................................................................

16

2.3 Connect the power

..................................................................................................................................

17

2.4 Adjust the media sensors

......................................................................................................................

18

2.4.1 Two types of media sensors

..........................................................................................................

18

2.4.2 Relocate the Gap Sensor

...............................................................................................................

19

2.4.3 Relocate the (Reflective) Black Mark Sensor

.............................................................................

19

2.5 Load the media

........................................................................................................................

20

2.5.1 Loading procedures

........................................................................................................................

20

2.5.2 Adjust the media thickness and width

..........................................................................................

22

2.6 Load the ribbon

........................................................................................................................

24

2.6.1 Loading procedures

........................................................................................................................

24

2.6.2 Resolve the wrinkled ribbon by adjusting the Ribbon Balance Gear

.....................................

25

2.6.3 Resolve the wrinkled ribbon by adjusting the Ribbon Supply Leveler

...................................

26

2.7 Connect the interface

.............................................................................................................................

27

CHAPTER 3 SOFTWARE INSTALLATION................................................................................................. 28

3.1 Installing the Driver

.................................................................................................................................

28

3.2 Installing the Configuration Tool

...........................................................................................................

32

3.3 Using the Configuration Tool

.................................................................................................................

35

3.3.1Setup for the media with black marks

...........................................................................................

35

3.3.2 Setup for the LAN connection

.......................................................................................................

37

3.4 Upgrading the Firmware

........................................................................................................................

38

CHAPTER 4 SUPPORT UTILITIES...............................................................................................................40

4.1 Configuration list (self-test page)

.........................................................................................................

40

4.2 Hex-dump

........................................................................................................................

41

4.3 Auto media registration

........................................................................................................................

41

CHAPTER 5 DIAGNOSTICS AND MAINTENANCE..................................................................................42

5.1 Diagnostics

...............................................................................................................................................

42

5.2 Restore factory default settings

............................................................................................................

43

5.3 Clear jammed media

..............................................................................................................................

43

5.4 Clean the print head

...............................................................................................................................

43

5.5 Cleaning

....................................................................................................................................................

44

Tally Dascom DL-820 User Guide V1.0

CHAPTER 6 INTERFACE SPECIFICATIONS............................................................................................ 45

6.1 USB

...........................................................................................................................................................

45

6.2 Ethernet

....................................................................................................................................................

45

6.3 Parallel

......................................................................................................................................................

46

6.4 Serial

.........................................................................................................................................................

47

6.5 Wifi

.............................................................................................................................................................

47

CHAPTER 7 OPTION INTRODUCTION.......................................................................................................49

7.1 Using the cutter.......................................................................................................................................49

7.2 Using the peeler......................................................................................................................................50

CHAPTER 8 CODE PAGES........................................................................................................................... 54

8.1 ASCII character set

.................................................................................................................................

54

8.2 CP 437 USA

.............................................................................................................................................

55

8.3 CP 850

......................................................................................................................................................

56

8.4 CP 860 Portuguese

................................................................................................................................

57

8.5 CP 863 French

........................................................................................................................................

58

8.6 CP 865 Nordic

.........................................................................................................................................

59

8.7 CP 858 European

....................................................................................................................................

60

8.8 CP 866 Cyrillic

.........................................................................................................................................

61

8.9 CP 852 Latin

............................................................................................................................................

62

CHAPTER 9 COMMAND CODES................................................................................................................. 64

9.1 ZPL Command Set

.................................................................................................................................

64

9.2 EPL Command Set

.................................................................................................................................

68

Tally Dascom DL-820 User Guide V1.0

1

Chapter 1 Introduction

Dascom designs this competitive industrial thermal label printer with the resolution of 203 dpi

(dots per inch) printing at 8 ips (inches per second). Generous media storage and multiple

emulations supporting ZPL, EPL, TSPL best fit for medical, manufacturing, logistics, retail & service,

postal and education applications.

1.1 Features

Nearly 90



cap opening for effortless media and ribbon replacement.

Pull down to tear for easy cutting of short-width labels.

Generous storage for 360-meter ribbon and 203 mm diameter media to reduce frequent

replacement.

Movable media sensor for precise positioning of media with off-center registration maker.

Multiple interfaces: USB and LAN built-in, parallel option.

Other optional parts:

Cutter, label peeler

Tally Dascom DL-820 User Guide V1.0

2

1.2 Specifications

Print

Parameter

Print method

Direct thermal/Thermal transfer printing

Print width

Max. 108mm

Print speed

Max. 8 ips (203dpi)

Print head

Dot pitch: 0.125mm

Resolution

203DPIx203DPI

Fonts

Chinese

GB18030 24×24 (Simplified/Traditional Chinese)

Alphanumeric

Resident single byte (ZPL): Font A, Font B, Font D, Font E, Font F, Font G,

Font H, Font V0, Font GS, Font P, Font Q, Font R, Font S, Font T, Font U,

Font V

User-defined

User-defined fonts can be downloaded into FLASH, SDRAM.

Code Pages

EPL:

PC437;PC850;PC852;PC860;PC863;PC865;PC857;PC861;PC862;PC85

5;PC866; PC737;PC851;PC869;Windows 1252;Windows 1250;Windows

1251; Windows 1253;Windows 1254;Windows 1255

ZPL:

PC850, windows 1250, windows 1252, windows 1251, windows 1253,

windows 1254, windows 1256

Scalable

/Rotation

Zoom in 1~8 times in vertical or horizontal, rotate by 0

0

, 90

0

, 180

0

, 270

0

.

Graphics

processing

Graphics (Monochrome PCX, BMP) can be downloaded into SDRAM.

Barcodes

1D

ZPL:

Code11;Interleaved 2 of 5;Code 39;Code 49;Planet Code;

EAN-8;EAN-13;UPC-E;UPC-A;Code 93;Code 128;

Industrial 2 of 5;Standard 2 of 5;Codabar;MSI;Plessey

EPL:

EAN-8;EAN-13;UPC-E;UPC-A;Code 39;Code 93;Code 128; Interleaved 2

of 5

2D

ZPL:

PDF417;CODABLOCK;Maxicode;Aztec;QR Code; Data Matrix;

EPL:

PDF417;Maxicode;QR Code; Data Matrix;

Ribbon

OD

Max. φ70mm (2.7 in)

ID

φ25 mm (1 in)

Length

Max. 360 m

Width

25.4~114mm

Media

Handling

Media Spec.

Thickness 0.06~0.25mm

Width 19.6mm~120mm

Length 8.9~400mm

Max. OD φ203mm (8 in)

ID φ25.4 mm~76.2 mm (1 inch~3 inch)

Media cut

Tear bar, auto-cutter, peeler

Media type

Roll paper, fanfold paper

(continuous, non-continuous, continuous tag, wrist-band, normal media

and all sorts of receipts )

Control

Panel

Key

Four keys: Feed, Return, Pause, Cancel

LED indicator

One LED: Power

Screen

LCD

Detect

Function

Standard

sensors

Black mark sensor, Media sensor, Ribbon sensor, Machinery sensor

Optional kit

sensor

Label peel-off sensor

Emulation

Zebra

ZPL, EPL, TSPL

Tally Dascom DL-820 User Guide V1.0

3

Power

Supply

External power adapter

Input

AC 100V-240V, 50-60Hz

Output

DC 24V；1.5A

Memory

SDRAM

32MB

FLASH

8 MB

Interface

Standard

USB (2.0 Full-Speed)

Ethernet: 10M/100M

Optional

Parallel Centronics (IEEE-1284)

Software

Driver (Windows 32bit/64bit), Bartender, SDK system

Physical

Spec.

Dimensions

240(W)×440(D)×255(H)mm

Casing Color

Black

Weight

9.8kg

Operating

condition

0~45℃ 20%~95%RH (non-condensing)

Storage

condition

-20~60℃/≤95%RH (non-condensing)

Certification

CE, FCC

Optional kit

Cutter, Peeler

Reliability

TPH lifetime

150km

(Condition: use specific thermal roll paper and the print rate is 12%)

1.3 Consumables

Important: Use genuine media to ensure the best print quality. The special

designed paper, polyethylene and polyester media improve the performance

and the print head life.

This printer supports three classes of print media:

Adhesive Labels - individual label or continuous roll, with adhesive material on its back, laying

over a backing tape (liner).

Receipt - generally thermal sensitive paper in a roll.

Ticket & Tag - generally made of thick paper (max. 0.25 mm); with perforation between label.

The print media can be in a roll or fanfold.

Thermal sensitive media (direct thermal) must be used without ribbon.

Choose correct type of media for your application.

Tally Dascom DL-820 User Guide V1.0

4

1.4 Size and Weight

Width: ~240 mm

Length: ~ 440 mm

Height: ~255 mm

Weight: ~9.8kg

Front View

Rear View

Side View

Tally Dascom DL-820 User Guide V1.0

5

1.5 Unpack and Inspect

Unpack and inspect if any shipping damage or missing parts compared with the packing list:

Save all packing materials.

Check if any exterior damages.

Open the printer and inspect if any damages in the media compartment.

If you find shipping damage, keep the packing materials and notify the re-seller.

Contents in the packing list may vary according to your order.

Tally Dascom DL-820 User Guide V1.0

6

Packing List for Standard Order：

Parts

Quantity

Remark

Printer

1 set

Ribbon

1 roll

Wax base

Ribbon Rewinding Core

1 piece

Media Holder

1 piece

Thermal Paper

1 roll

Ribbon Spindles

2 pieces

Media Width Adjuster

1 piece

Power Cord

1 piece

USB Cable

1 piece

GIG

1 copy

CD

1 piece

Contents: User

Guide, GIG, Driver,

Configuration Tool

Tally Dascom DL-820 User Guide V1.0

7

1.6 Standard/optional components for the product

Product

Interfaces

Cutting

Sensor

USB

LAN

Serial

Parallel

WLAN

Blue

tooth

Tear

Cutter

Label

Peeler

Black

Mark

DL-820

√

X

O

X

√

O

√

Remarks: “√” denotes standard component.

“O” denotes optional component.

“X” denotes unavailable component.

Parallel (optional)

USB

LAN

Tally Dascom DL-820 User Guide V1.0

8

1.7 Key components

No.

Part Names

Descriptions

1

Transparent Window

Observe quantity of remained media.

2

Top Cover

Open to replace media or ribbon.

3

Control Panel

Configure the parameters and check the settings.

4

Rear Slot

An opening to load fanfold media

5

Power Socket

Socket for detachable power cord.

6

Power Switch

Turn on and off the printer

7

USB Interface

USB connection to PC (ex-factory standard interface)

8

LAN Interface

LAN connection to the server (ex-factory standard

interface)

9

Optional interface:

parallel

Optional interface to the PC. (Ordered separately)

2

1

6

9

7

5

3

8

4

La pagina si sta caricando...

Dascom DL-820 Guida utente

Dascom DL-820 Guida utente

in altre lingue

Documenti correlati

Altri documenti