Dascom DL-310 Guida utente

User Manual DL-310 Label & Barcode Printer

Tally Dascom DL-310 User Guide V1.2

I

Important Safety Instructions (English)

Read the following instructions thoroughly before starting up your printer.

• The device and mains-socket must all times be easily accessible.

• Never carry out maintenance or repair work yourself. Always contact a qualified service

technician.

• Keep this user guide in a place which is easily accessible at all times.

• Place the printer on a solid and even base so that it cannot fall.

• Never place the printer in the vicinity of inflammable gas or explosive substances.

• Ensure the printer is connected to a socket with the correct voltage.

• Always disconnect the printer from the power before opening the device to perform

maintenance work or remedy errors.

• Do not expose the printer to high temperatures, direct sunlight or dust.

• Keep all liquids away from the printer.

• Protect the printer from shock, impact and vibration.

• Make sure that both the printer and the computer are switched off before connecting the data

cable.

• The print head will become very hot during printing; avoid contact with the print head after

printing has finished.

• Do not perform any operation or action in any way other than those provided in this manual.

When in doubt, contact your dealer or your customer support.

Tally Dascom DL-310 User Guide V1.2

II

Wichtige Sicherheitshinweise (German)

Lesen Sie bitte diese Sicherheitshinweise durch, bevor Sie den Drucker in Betrieb nehmen.



Das Gerät und die Netzsteckdose müssen jeder Zeit leicht zugänglich sein.

 Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie

immer einen qualifizierten Servicetechniker.

 Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.

 Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen

kann.



Stellen Sie den Drucker keinesfalls in der Nähe von leicht entzündlichen Gasen oder explosiven

Stoffen auf.

 Den Drucker nur an eine Steckdose mit der richtigen Spannung anschließen.

 Wenn Sie den Drucker vom Netz trennen wollen, den Drucker ausschalten und immer den

Netzstecker an der Steckdose ziehen.



Den Drucker weder hohen Temperaturen noch direktem Sonnenlicht und Staub aussetzen.

 Keine Flüssigkeiten mit dem Drucker in Berührung bringen.



Den Drucker keinen Erschütterungen, Stößen oder Vibrationen aussetzen.

 Sicherstellen, dass der Drucker und der Computer ausgeschaltet sind, bevor das Datenkabel

angeschlossen wird.



Der Druckkopf wird während des Druckens heiß. Vor dem Berühren deshalb einige Zeit abkühlen

lassen.

 Weichen Sie bei der Bedienung des Druckers nicht von den Anweisungen in der Dokumentation

ab. Bei Unklarheiten wenden Sie sich bitte an Ihren Händler oder Ihren Kundendienst.

Tally Dascom DL-310 User Guide V1.2

III

Consignes importantes de sécurité (French)

Lire attentivement les instructions suivantes avant de mettre l’imprimante en service.



Le dispositif et la prise principale doivent toujours être accessibles facilement.

 Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un

dépanneur qualifié.

 Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.

 Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de

substances explosives.



Ne connecter l’imprimante à une prise que lorsque la tension est correcte.

 Pour déconnecter l’imprimante de l’alimentation principale, mettre l’imprimante hors tension et

toujours débrancher le connecteur secteur de la prise murale.

 Ne pas exposer l’imprimante à des températures élevées, à la lumière directe du soleil ou à la

poussière.



Ne pas mettre l’imprimante en contact avec des liquides.

 Ne pas exposer l’imprimante à des chocs, impacts ou vibrations.



S’assurer que l’imprimante et l’ordinateur sont hors tension avant de connecter le câble de

données.

 La tête d’impression est brûlante pendant l’impression. C’est pourquoi laissez-la refroidir

quelques instants avant d’y toucher.



N'exécutez aucune opération ni action d'une autre manière que celle indiquée dans ce manuel.

En cas de doute, veuillez contacter votre distributeur ou service après-vente.

Tally Dascom DL-310 User Guide V1.2

IV

Indicazioni di sicurezza importanti (Italian)

Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni.



Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili.

 Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un

tecnico di assistenza qualificato.

 Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.

 Collocare la stampante su una superficie stabile, per evitare che cada a terra.



Non collocare la stampante in prossimità di gas facilmente infiammabili o di sostanze esplosive.

 Collegare la stampante a una presa di corrente con tensione adeguata.

 Per scollegare la stampante dalla rete di alimentazione, spegnere la stampante e disinserire

sempre il connettore di rete dalla presa.



Non esporre la stampante ad elevate temperature né alla luce solare diretta e alla polvere.

 Evitare il contatto della stampante con liquidi.



Non esporre la stampante a colpi, scosse o vibrazioni.



Verificare che la stampante e il computer siano spenti prima di collegare il cavo di trasmissione

dati.

 Durante la stampa, la testina si surriscal-da notevolmente. Prima di toccarla, se necessario

opportuno quindi lasciarla raffreddare qualche istante.

 Non eseguire alcuna operazione o azione se non nella maniera descritta nel presente manuale.

In caso di dubbio, contattare il rivenditore o dalla società incaricata dell’assistenza.

Tally Dascom DL-310 User Guide V1.2

V

Instrucciones de seguridad importantes (Spanish)

Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio.



El dispositivo y la toma de corriente deben estar ubicados de forma que sea fácil acceder a ellos.

 Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un

técnico de servicio calificado.

 Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.

 Ponga la impresora sobre un superficie estable de manera que no pueda caer al suelo.



Nunca coloque la impresora en la vecindad de gases inflamables o sunstancias explosivas.

 Asegure conectar la impresora sólo a un enchufe con un voltaje correcto.

 Cuando quiera desconectar la impresora de la red, apague la impresora y siempre hale de la

clavija de alimentación del enchufe nunca del cable.



No exponga la impresora a temperaturas altas, a la luz solar directa y al polvo.

 No ponga la impresora en contacto con fluidos.



Nunca exponga la impresora a sacudidas, choques o vibraciones.



Asegúrese de que la impresora y el ordenador estén apagdos antes de conectar el cable de

datos.

 La cabeza de impresión se pone muy caliente durante la impresión. Por lo tanto, Déjela enfriarse

algún tiempo antes de tocarla.

 No permita que se realice cualquier operación o acción de una forma diferente a lo que se señala

en el manual. En caso de duda, póngase en contacto con su comerciante o con su servicio

post-venta.

Tally Dascom DL-310 User Guide V1.2

VI

Правила по технике безопасности. (Russian)

Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу

принтера.

 Устройство и розетка должны быть всегда легко доступна.

 Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о

неисправностях квалифицированным сервисным техникам.



Данная инструкция должна быть всегда доступна каждому пользователю.

 Установите принтер на ровном и стабильном месте так, чтобы он не смог упасть на пол.



Ни в коем случае не ставьте принтер вблизи легко воспламеняющихся газов и взрывчатых

веществ.

 Включайте принтер в розетку только с соответствующим напряжением.

 Если Вы хотите отключить принтер от напряжения, сначала выключите принтер сам и затем

выньте штекер из розетки.



Берегите принтер от нагревания, от попадания на него прямых солнечных лучей и пыли.

 Не допускайте попадания жидкости на принтер.



Нельзя подвергать принтер тряске, ударам и вибрации.

 Убедитесь, что принтер и компьютер выключены, только после этого соедините принтер с

компьютером.



Печатающая головка нагревается во время работы принтера. Поэтому подождите какое-то

время, прежде чем дотронуться до нее.

 Пользуйтесь принтером так, как это написано в документации. Если у Вас возникают

неясности, обращайтесь с вопросами к Вашим продавцам или в сервисный центр.

Tally Dascom DL-310 User Guide V1.2

VII

Instruções Importantes sobre Segurança (Portuguese)

Leia as instruções de segurança antes de usar a impressora.



A impressora e a tomada devem ser facilmente em todos os momentos acessíveis.

 Consulte sempre um técnico qualificado para executar uma reparação .



Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas.

 Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias

explosivas.



Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.

 Quando desligar a impressora da rede, desligue sempre a impressora e retire o cabo da tomada.

 Não exponha a impressora a temperaturas altas ou luz solar direta.



Não aproxime substâncias líquidas da impressora.

 Proteja a impressora de choques, impactos e vibrações.



Desligue a impressora e o computador antes de conectar o cabo da rede.



A cabeça da impressora pode ficar muito quente . Portanto, espere algum tempo antes de

tocá-la.

 Não faça nenhuma operação ou ação além das recomendadas neste manual. Em caso de dúvida,

contate seu revendedor ou companhia de serviço.

Tally Dascom DL-310 User Guide V1.2

VIII

Önemli Güvenlik Talimatları (Turkish)

Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun.



Cihaz ve elektrik prizinin her zaman kolayca erişilebilir olması gerekir.

 Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman

kalifiye bir uzman servis-teknisyenine haber verin.

 Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.

 Yazıcıyı kesinlikle ve hiçbir surette kolayca yanabilecek gaz veya patlayıcı maddeler içeren

nesnelerin yakınına koymayın.



Yazıcı akım kablosunu sadece doğru gerilime sahip bir prize takın.

 Yazıcıyı şebeke ağından ayırmak istediğinizde, yazıcıyı kapatın ve ağ-fişini her zaman prizden

çıkartın.

 Yazıcıyı ne yüksek ısılı ne de doğrudan güneş ışığına ve toza mâruz kalan mekânlarda bulundurun.



Yazıcı hiçbir sıvı maddeyle temasta olmamalıdır.

 Yazıcı hiçbir sarsıntıya, darbeye veya titreşime mâruz kalmamalıdır.



Veri kablosu bağlanmadan önce hem yazıcının hem de bilgisayarın kapalı olduklarından emin

olmalısınız.

 Yazıcının başı basma esnasında yüksek ısıya ulaşıyor. Bu yüzden lütfen dokunmadan önce kısa

süre soğumasını bekleyin.



Yazıcının işletimi ve kullanımında bu dokümantasyondaki talimatların hiç dışına çıkmayın. Sorunlu

görünen hususlarda lütfen imâlatçınıza veya müşteri hizmetleri servisinize başvurun.

Tally Dascom DL-310 User Guide V1.2

IX

TRADEMARK ACKNOWLEDGEMENTS

“IBM” is a trademark of International Business Machines Corporation.

“EPSON” is a trademark of Epson America Incorporated.

“DEC” is a trademark of Digital Equipment Corporation.

“Centronics” is a trademark of Centronics Data Computer Corporation.

“DOS” is a trademark of Microsoft Corporation.

“SAP” is a trademark of SAP AG.

“Windows”, “Windows 7”,”Windows 8”, “Windows 95”, “Windows 98“, “Windows NT”, “Windows

2000”, “Windows 2003/2008/2012/2012R2 Server”, “Windows XP” and “Windows Vista” are

trademarks of Microsoft Corporation.

All other product names and company names appearing in this manual are the registered

trademarks or trademarks of their repective holders.

Tally Dascom DL-310 User Guide V1.2

X

About This Manual

This manual provides information to operators of the DL-310 to describe basic operations to enable safe and

correct use of the printer.

Symbols Description

The symbols in this manual are identified by their level of importance, as defined below. Read the following

carefully before handling the product.

CAUTION: Provides information that must be observed to prevent damage to the

equipment or loss of date.

NOTE: Advises you of information that is essential to complete a task.

Related Software and Documents

Software/document name

Description

DL-310 User Manual

This manual.

DL-310 Maintenance Manual

This manual provides developer/ engineers

with additional technical information.

Tally Dascom DL-310 User Guide V1.2

TABLE OF CONTENTS

About This Manual

...................................................................................................................................

X

1 INTRODUCTION

.....................................................................................................................................

1

1.1 Features

..........................................................................................................................................

1

1.2 Printer specifications

......................................................................................................................

2

1.3 Print Media Types

...........................................................................................................................

4

1.4 External Dimension and Weight

.....................................................................................................

6

1.5 Unpacking

.......................................................................................................................................

7

1.6 Product Configuration

.....................................................................................................................

9

1.7 Printer Components

......................................................................................................................

10

1.8 Control Panel

.................................................................................................................................

13

1.8.1 LEDs Behavior

.........................................................................................................................

13

1.8.2 Feed Button Operation

...........................................................................................................

13

2 SETUP

...................................................................................................................................................

15

2.1 Flow of Setup

................................................................................................................................

15

2.2 Placing the Printer

.........................................................................................................................

15

2.3 Attaching Power

............................................................................................................................

16

2.4 Calibrate Sensor

............................................................................................................................

17

2.4.1 Calibrate Gap Sensor

..............................................................................................................

17

2.4.2 Calibrate Reflective Sensor

.....................................................................................................

17

2.5 Loading Roll Media

........................................................................................................................

19

2.6 Loading Transfer Ribbon

...............................................................................................................

21

2.7 Connecting to Computer

..............................................................................................................

24

2.7.1 Connecting USB interface

.......................................................................................................

25

2.7.2 Connecting serial interface

.....................................................................................................

25

2.7.3 Connecting parallel interface

.................................................................................................

26

2.7.4 Connecting Ethernet interface

...............................................................................................

26

2.7.5 Connecting Wlan Interface

.....................................................................................................

27

3 NETWORK SETUP AND CONFIGURATION

............................................................................................

28

3.1 Installing Driver

.............................................................................................................................

28

3.2 Installing Setup Tool

......................................................................................................................

34

3.3 Setup Tool Application

..................................................................................................................

38

3.3.1 Model and Interface Setting

...................................................................................................

38

3.3.2 Configuring Printer

.................................................................................................................

39

3.4 LAN Interface Setup

......................................................................................................................

41

3.5 WLAN Interface Setup

...................................................................................................................

43

3.6 Install Bluetooth Adapter Driver

...................................................................................................

45

3.7 Bluetooth Setup

............................................................................................................................

50

3.8 Update Firmware

..........................................................................................................................

52

3.9 Cutter and Peeler Setup（Option）

.............................................................................................

54

4 SETTING/CHECKING MODES

................................................................................................................

56

4.1 Print a Parameter Setting Page (Self-test Page)

............................................................................

56

4.2 Hexadecimal Dumping Mode

.......................................................................................................

58

Tally Dascom DL-310 User Guide V1.2

4.3 Auto Calibrate Label

......................................................................................................................

59

5 TROUBLESHOOTING AND MAINTENANCE

..........................................................................................

60

5.1 Common Issues

.............................................................................................................................

60

5.2 Resetting the Factory Default Values

............................................................................................

61

5.3 Removing Jammed Label

..............................................................................................................

61

5.4 Cleaning Thermal Print Head

........................................................................................................

62

5.5 Maintenance

.................................................................................................................................

62

6 COMMUNICATION INTERFACES SPECIFICATIONS

................................................................................

63

6.1 USB interface

.................................................................................................................................

63

6.2 Wi-Fi interface

...............................................................................................................................

63

6.3 Bluetooth Interface

.......................................................................................................................

63

6.4 Ethernet interface

.........................................................................................................................

63

6.5 Serial interface

..............................................................................................................................

64

6.6 Parallel interface

...........................................................................................................................

65

6.7 Power Supply

................................................................................................................................

66

7 CHARACTER CODE PAGES

....................................................................................................................

67

7.1 Common to all pages (International Character Set: USA)

.............................................................

67

7.2 International Character Sets

.........................................................................................................

68

7.3 [User-defined page]

......................................................................................................................

69

7.4 [PC437: USA, Standard Europe]

....................................................................................................

70

7.5 [PC850: Multilingual]

....................................................................................................................

71

7.6 [PC852: Latin2]

..............................................................................................................................

72

7.7 [PC858: Euro]

................................................................................................................................

73

7.8 [PC860: Portuguese]

.....................................................................................................................

74

7.9 [PC863: Canadian-French]

............................................................................................................

75

7.10 [PC865: Nordic]

...........................................................................................................................

76

7.11 [PC866: Cyrillic #2]

......................................................................................................................

77

7.12 [PC720: Arabic]

...........................................................................................................................

78

8 COMMAND SETS

..................................................................................................................................

79

8.1 ZPL Command Sets

........................................................................................................................

79

8.2 EPL Command Sets

.......................................................................................................................

85

8.3 TSPL Command Sets

......................................................................................................................

86

Appendix I: AUTOCUTTER（OPTION）

..................................................................................................

87

Appendix II: PEELER（OPTION）

...........................................................................................................

91

Appendix III: FCC STATEMENT

................................................................................................................

92

Appendix IV: DASCOM REPRESENTATIVES

..............................................................................................

93

Tally Dascom DL-310 User Guide V1.2

1

1 INTRODUCTION

The Dascom® DL-310 model is the best value in a desktop thermal printer. The DL-310 printer

provides thermal transfer and direct thermal printing at speeds up to 102mm per second at a 300

dpi (dots per inch) print density.

1.1 Features

• Easy to switch printer language between ZPL, EPL and TSC programming and label formats.

• Easy operation. With an open structure users can easily change paper roll and ribbon.

• Large media compartment. Ribbon as long as 300m and paper roll of Max. OD φ127mm can be

used. Therefore users can change the ribbon and paper roll less often so as to work more efficiently.

•Wide range of connectivity. The USB port is the standard interface. Serial/parallel/Ethernet/ Wi-Fi/

Bluetooth are optional interfaces. Various interface choices suit all needs.

The DL-310 printers offer these basic printer options:

• Auto cutter.

•Peeler.

This user guide provides all the information you need to operate your printer on a daily basis.

Tally Dascom DL-310 User Guide V1.2

2

1.2 Printer specifications

Print

Parameter

Print method

Direct thermal/Thermal transfer printing

Print width

106mm

Print speed

102mm/s (300DPI)

Print head

Dot pitch: 0.084mm

Resolution

300DPIx300DPI

Fonts

Chinese

GB18030 24×24 (Simplified/Traditional Chinese)

Alphanumeric

Resident single byte (ZPL): Font A, Font B, Font D, Font E, Font F, Font G,

Font H, Font V0, Font GS, Font P, Font Q, Font R, Font S, Font T, Font U,

Font V

User-defined

User-defined fonts can be downloaded into FLASH, SDRAM.

Code Pages

ZPL:

PC850, windows 1250, windows 1252, windows 1251, windows 1253,

windows 1254, windows 1256

Scalable/Rotation

Zoom in 1~8 times in vertical or horizontal, rotate by 0

0

, 90

0

, 180

0

, 270

0

.

Graphics

Graphics (Monochrome PCX, BMP) can be downloaded into SDRAM.

Barcodes

1D

ZPL:

Code11;Interleaved 2 of 5;Code 39;Code 49;Planet Code;

EAN-8;EAN-13;UPC-E;UPC-A;Code 93;Code 128;

Industrial 2 of 5;Standard 2 of 5;Codabar;MSI;Plessey

2D

ZPL:

PDF417;CODABLOCK;Maxicode;Aztec;QR Code;Data Matrix;

Ribbon

ID

φ25.4mm

OD

φ68mm

Length

300m

Width

33~110mm

Media Handling

Media Spec.

Thickness 0.06~0.18mm

Width 25~118mm

Length 8.9~400mm

Max. OD ∮127mm

Min. ID φ25.4/38.1mm

Media cut

Tear bar, auto-cutter, peeler

Media type

Roll paper, fold paper

(continuous, non-continuous, continuous tag, wrist-band, normal media

and all sorts of receipts )

Control Panel

Button

One Button: Feed

LED indicator

Three LEDs: Power, Error, Status (Paper out/Ribbon out)

Detect Function

Standard sensors

Black mark sensor, Media sensor, Ribbon sensor, Machinery sensor

Optional kit sensor

Label taken sensor

Emulation

Zebra, EPSON

ZPL, EPL, TSC

Power Supply

External power adapter

Input

AC 100V-240V, 50-60Hz

Output

24V DC, 2.15A

Memory

SDRAM

16MB

FLASH

8MB

Interface

Standard

USB (2.0 Full-Speed)

Optional

Serial (RS-232, DB25)

Parallel Centronics (IEEE-1284)

Ethernet: 10M/100M

Tally Dascom DL-310 User Guide V1.2

3

Wi-Fi (802.11b/g/n)

Bluetooth: SPP

Software

Driver (Windows 32bit/64bit), Bartender, SDK system

Physical Spec.

Dimensions

230(W)×290(D)×176(H)mm

Casing Color

Black

Weight

Approx 3kg

Operating condition

5～40℃/20～95%RH (non-condensing)

Storage condition

-20～60℃/≤95%RH (non-condensing)

Safety Regulation

Safety

CE (LVD/CB and EMC) and FCC/UL

EMC

Class B

Certificate

CCC, CE, FCC, UL, Energy star

Option

Cutter

Media width：25mm~118mm

Media thickness：0.06mm~0.18mm

Peeler

Media width：25.4mm-100mm

Media thickness：0.06mm~0.18mm

Reliability

TPH lifetime

150km

(Condition: use specific thermal roll paper and the print rate is 12%)

Tally Dascom DL-310 User Guide V1.2

4

1.3 Print Media Types

Important •Dascom strongly recommends the use of Dascom-brand supplies for

continuous high-quality printing.

Your printer can use various types of media:

• Standard media—Most standard (non-continuous) media uses an adhesive backing that sticks

individual labels or a continuous length of labels to a liner.

• Continuous roll media—Most continuous roll media is direct thermal media (similar to FAX paper)

and is used for receipt or ticket style printing.

• Tag stock—Tags are usually made from a heavy paper (up to 0.0075in./0.19mm thick). Tag stock

does not have adhesive or a liner, and it is typically perforated between tags.

For more information on basic media types, see the following table.

The printer typically uses roll media, but you can use fan-fold or other continuous media too. Use the

correct media for the type of printing you require. You must use direct thermal media. When

printing without a ribbon, you must use direct thermal media. When using ribbon, you must use

thermal transfer media.

Tally Dascom DL-310 User Guide V1.2

5

Media Type

How it looks

Description

Non-Continuous

Roll Media

Roll media is wound on a core that can be 1 to 1.5

in. (25.4 to 38.1 mm) in diameter. Labels have

adhesive backing that sticks them to a liner, and

gaps, holes, notches, or black marks separate them.

Tags are separated by perforations. Individual labels

are separated by one or more of the following

methods:

• Web media separates labels by gaps, holes, or

notches.

• Black mark media uses pre-printed black marks on

the back side of the media to indicate label

separations.

• Perforated media has perforations that allow the

labels or tags to be separated from each other

easily. The media may also have black marks or

other separations between labels or tags.

Non-Continuous

Fanfold Media

Fan-Fold media is folded in a zigzag pattern. Fanfold

media can have the same label separations as

non-continuous roll media.

The separations would fall on or near the folds.

Continuous Roll

Media

Roll media is wound on a core that can be 1 to 1.5

in. (25.4 to 38.1 mm) in diameter. Continuous roll

media does not have gaps, holes, notches, or black

marks to indicate label separations. This allows the

image to be printed anywhere on the label. A cutter

can be used to cut apart individual labels. With

continuous media, use the transmissive (gap)

sensor so the printer can detect when the media

runs out.

Tally Dascom DL-310 User Guide V1.2

6

1.4 External Dimension and Weight

 Width: Approximately 230 mm



Depth: Approximately 290 mm

 Height: Approximately 179.5 mm

 Mass: Approx. 3 kg (excluding power adapter)

Front View

Back view

Side view

Tally Dascom DL-310 User Guide V1.2

7

1.5 Unpacking

When you receive the printer, please check for possible shipping damage:

1. Inspect the outside of both the box and the printer for possible damage.

2. Open the top cover of the printer to see if the media compartments are in order.

If you discover shipping damage upon inspection:



Immediately notify the shipping company and file a damage report.

 Keep all packaging material for shipping company inspection.

 Notify your authorized Tally Dascom reseller.

The package contents vary with different customized order requirements.

DL-310 printer

Ribbon

Power cord

CD-ROM

Ribbon Rewind Paper Core

Power Adapter

Media

La pagina sta caricando ...

Dascom DL-310 Guida utente

Dascom DL-310 Guida utente

in altre lingue

Documenti correlati

Altri documenti