Abit IN9 32X Manuale utente

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IN9 32X

-MAX

Motherboard

Socket 775

User’s Manual

About this Manual:

This user’s manual contains all the information you may

need for setting up this motherboard. To read the user’s

manual of PDF format (readable by Adobe Reader), place

the “Driver & Utility CD” into the CD-ROM drive in your

system. The auto-run screen will appear, click the

“

Manual” tab to enter its submenu. If not, browse the

root directory of the CD-ROM via the File Manager, and

double click the “AUTORUN” file.

 IN9 32X-MAX:

NVIDIA nForce 680i SLI

NVIDIA nForce 590 SLI MCP

IN9 32X:

NVIDIA nForce 680i LT SLI

NVIDIA nForce 570 SLI MCP

 FSB 1333 MHz

 Dual Channel DDR2 800

 Triple PCI-E X16 Slots

 Dual Gigabit LAN

 8x SATA 3Gb/s including 2x

external SATA Connectors

 USB 2.0 / IEEE1394

 7.1-Channel HD Audio

 abit uGuru™

Technology

 abit Silent OTES™ Technology

 External CMOS Clearing

Switch

 Quick Power & Reset Button

 Vista HW Ready

ii IN9 32X/IN9 32X-MAX

IN9 32X/IN9 32X-MAX

User’s Manual

English + Multilingual QIG

P/N: 4310-0000-76

Rev. 4.00, March 2007

Copyri

g

ht and Warranty Notice

The information in this document is sub

j

ect to chan

g

e without notice and does not represent a

commitment on part of the vendor, who assumes no liability or responsibility for any errors that

may appear in this manual.

No warranty or representation, either expressed or implied, is made with respect to the quality,

accuracy or fitness for any particular part of this document. In no event shall the manufacturer be

liable for direct, indirect, special, incidental or consequential damages arising from any defect or

error in this manual or product.

Product names appearin

g

in this manual are for identification purpose only and trademarks and

product names or brand names appearin

g

in this document are the property of their respective

owners.

This document contains materials protected under International Copyri

g

ht Laws. All ri

g

hts reserved.

No part of this manual may be reproduced, transmitted or transcribed without the expressed

written permission of the manufacturer and authors of this manual.

If you do not properly set the motherboard settin

g

s, causin

g

the motherboard to malfunction or

fail, we cannot guarantee any responsibility.

The Following Information is Only for EU-member States:

Directive 2002/96/EC on Waste Electrical and Electronic Equipment

(WEEE): The use of the symbol indicates that this product may not be

treated as household waste. By Ensurin

g

this product is disposed of correctly,

you will help prevent potential ne

g

ative consequences for the environment

and human health, which could otherwise be cause by inappropriate waste

handling of this product. For more detailed information about recycling of this

product, please contact your local city office, your household waste disposal

service or the shop where you purchased the product.

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IN9 32X/IN9 32X-MAX iii

Contents

1. Hardware Setup ............................................................... 1-1

1.1 Specifications............................................................................... 1-1

1.2 Motherboard Layout ..................................................................... 1-2

1.3 Choosing a Computer Chassis ....................................................... 1-3

1.4 Installing Motherboard ................................................................. 1-3

1.5 Checking Jumper Settings............................................................. 1-4

1.5.1 CMOS Memory Clearing Header and Backup Battery .............. 1-4

1.6 Connecting Chassis Components ................................................... 1-6

1.6.1 ATX Power Connectors......................................................... 1-6

1.6.2 Front Panel Switches & Indicators Headers ........................... 1-7

1.6.3 FAN Power Connectors ........................................................ 1-8

1.6.4 Additional Cooling Fan for NB Heatsink ................................. 1-9

1.7 Installing Hardware.................................................................... 1-10

1.7.1 CPU Socket 775................................................................. 1-10

1.7.2 DDR2 Memory Slots........................................................... 1-12

1.7.3 PCI Express X16 Add-on Slots (Install Graphics Card) .......... 1-13

1.8 Connecting Peripheral Devices .................................................... 1-15

1.8.1 Floppy and IDE Disk Drive Connectors ................................ 1-15

1.8.2 Serial ATA Connectors ....................................................... 1-16

1.8.3 Additional USB 2.0 Port Headers......................................... 1-17

1.8.4 Additional IEEE1394 Port Header........................................ 1-17

1.8.5 Internal Audio Connectors.................................................. 1-18

1.8.6 Front Panel Audio Connection Header ................................. 1-18

1.8.7 S/PDIF Output Connection Header...................................... 1-20

1.8.8 PCI and PCI Express X1 Slot............................................... 1-20

1.8.9 Guru Panel Connection Header........................................... 1-21

1.9 Onboard Indicators and Buttons.................................................. 1-22

1.9.1 POST Code Displayer ......................................................... 1-22

1.9.2 Power Source Indicators .................................................... 1-23

1.9.3 Onboard Buttons ............................................................... 1-23

1.10 Connecting Rear Panel I/O Devices ........................................... 1-24

2. BIOS Setup....................................................................... 2-1

2.1 μGuru

™

Utility .............................................................................. 2-2

2.1.1 OC Guru ............................................................................. 2-2

2.1.2 ABIT EQ.............................................................................. 2-5

2.2 Standard CMOS Features............................................................ 2-11

2.3 Advanced BIOS Features ............................................................ 2-13

2.4 Advanced Chipset Features......................................................... 2-16

2.5 Integrated Peripherals................................................................ 2-18

iv IN9 32X/IN9 32X -MAX

2.6 Power Management Setup .......................................................... 2-21

2.7 PnP/PCI Configurations .............................................................. 2-23

2.8 Load Fail-Safe Defaults............................................................... 2-24

2.9 Load Optimized Defaults............................................................. 2-24

2.10 Set Password ........................................................................... 2-24

2.11 Save & Exit Setup..................................................................... 2-24

2.12 Exit Without Saving .................................................................. 2-24

3. Driver & Utility ................................................................. 3-1

3.1 CD-ROM AUTORUN ...................................................................... 3-1

3.2 nVidia nForce Chipset Driver ......................................................... 3-2

3.3 Realtek HD Audio Driver ............................................................... 3-2

3.4 Silicon Image 3132 SATA Driver.................................................... 3-3

3.5 AirPace Wi-Fi Wireless Driver ........................................................ 3-4

3.6 USB 2.0 Driver ............................................................................. 3-4

3.7 abit μGuru ................................................................................... 3-5

3.8 Build NVRaid Floppy Disk Under Windows Environment .................. 3-6

3.9 Build SIL3132 SATA Floppy Disk Under Windows Environment........ 3-7

3.10 Build SIL3132 RAID Floppy Disk Under Windows Environment ...... 3-8

3.11 Build A Driver Disk Under DOS Environment ................................ 3-9

4. Multilingual Quick Installation Guide .............................. 4-1

4.1 Français//Guide d'Installation Rapide............................................. 4-1

4.2 Deutsch//Kurze Installationsanleitung............................................ 4-2

4.3 Italiano//Guida all’installazione rapida ........................................... 4-3

4.4 Español//Guía rápida de instalación............................................... 4-4

4.5 Português//Guia de instalação rápida ............................................ 4-5

4.6 Русский//Краткое руководство по установке .............................. 4-6

4.7 Eesti//Kiirpaigaldusjuhend ............................................................ 4-7

4.8 Latviski//Ātrās instalēšanas instrukcija........................................... 4-8

4.9 Lietuvių//Trumpas instaliavimo vadovas ........................................ 4-9

4.10 Polski//Instrukcja szybkiej instalacji........................................... 4-10

4.11 Magyar//Gyorstelepítési útmutató.............................................. 4-11

4.12 Türkçe//Hızlı Kurulum Kılavuzu.................................................. 4-12

4.13 اللغة العربية//دليل التركيب السريع....................... 4-13

4.14 فارسی// راﻩنمای نصب سریع............................................... 4-14

4.15 日本語//クイックインストールガイド ...................................... 4-15

4.16 한국어//빠른 설치 가이드 ....................................................... 4-16

4.17 Bahasa Malaysia//Panduan Pemasangan Ringkas ....................... 4-17

4.18 ไทย//คู่มือการติดตั้งอย่างย่อ ........................................................ 4-18

4.19 繁體中文................................................................................. 4-19

4.19.1 規格............................................................................... 4-19

Hardware Setup

BIOS Setup

Driver & Utility Multilingual QIG Appendix

IN9 32X/IN9 32X-MAX v

4.19.2 快速安裝略說.................................................................. 4-20

4.20 简体中文................................................................................. 4-21

4.20.1 规格............................................................................... 4-21

4.20.2 快速安装略说.................................................................. 4-22

5. Appendix .......................................................................... 5-1

5.1 POST Code Definitions.................................................................. 5-1

5.1.1 AWARD POST Code Definitions............................................. 5-1

5.1.2 AC2005 POST Code Definitions............................................. 5-4

5.2 Troubleshooting (How to Get Technical Support?).......................... 5-5

5.2.1 Q & A ................................................................................. 5-5

5.2.2 Technical Support Form....................................................... 5-8

5.2.3 Contact Information............................................................. 5-9

vi IN9 32X/IN9 32X -MAX

Hardware Setup

IN9 32X/IN9 32X-MAX 1-1

1. Hardware Setup

1.1 Specifications

CPU

• LGA775 socket for Intel Core 2 Quad /

EE / Duo & Pentium Dual Core / EE / D

/ 4 processor

• Supports FSB 1333MHz

Chipset

• IN9 32X-MAX:

NB: NVIDIA nForce 680i SLI

SB: NVIDIA nForce 590 SLI MCP

• IN9 32X:

NB: NVIDIA nForce 680i LT SLI

SB: NVIDIA nForce 570 SLI MCP

Memory

• 4x 240-pin DIMM slots support

maximum memory capacity up to 32GB

• Supports Dual Channel DDR2 800

Un-buffered ECC/Non-ECC memory

Graphics

• Two PCI-Express X16 slots support

NVIDIA Scalable Link Interface

LAN

• Dual NVIDIA Gigabit Ethernet

Audio

• Onboard 7.1-CH HD Audio CODEC

• Supports auto jack sensing and optical

S/PDIF In/Out

• HDMI Header ready (S/PDIF Header)

Serial ATA

• 6x internal SATA 3Gb/s supports SATA

RAID 0, 1, 0+1, 5, and JBOD

• 2x external SATA 3Gb/s connectors

supports SATA RAID 0, 1

IEEE1394

• Supports 2 Ports IEEE1394 at 400Mb/s

transfer rate

Expansion Slots

• 2x PCI-E X16 slots (X16 bandwidth)

• 1x PCI-E X16 slot (X8 bandwidth)

• 2x PCI-E X1 slots

• 2x PCI slots

Internal I/O Connectors

• 1x Floppy port

• 1x Ultra ATA 133 IDE connector

• 6x SATA 3Gb/s connectors

• 3x USB 2.0 headers

• 2x IEEE1394 headers

• 1x FP-Audio header

• 1x CD-In connector

• 1x S/PDIF Out header

• 1x GURU header

Rear Panel I/O

• 1x PS/2 Keyboard connector

• 1x PS/2 Mouse connector

• 1x External CMOS Clearing Switch

• 1x S/PDIF In connector

• 1x S/PDIF Out connector

• 2x eSATA connectors

• 1x 7.1-CH Audio connector

• 4x USB 2.0 connectors

• 2x RJ-45 Gigabit LAN connectors

abit Engineered

• abit uGuru

™

Technology

• abit Silent OTES

™

Technology

• External CMOS Clearing Switch

• Quick Power & Reset Button

RoHS

• 100% Lead-free process and RoHS

compliant

Miscellaneous

• ATX form factor (305mm x 245mm)

• Vista HW Ready

※ Specifications and information contained herein are subject to change without

notice.

1-2 IN9 32X/IN9 32X -MAX

1.2 Motherboard Layout

※ The motherboard and its component layouts illustrated in this manual were

mainly based on model “IN9 32X-MAX”, unless specifically stated.

For model “IN9 32X”, still you may refer to “IN9 32X-MAX”. They both have the

same location and definition in headers, connectors, and jumpers, except a

different chipset heatsink assembly.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-3

1.3 Choosing a Computer Chassis

• Choose a chassis big enough to install this motherboard.

• As some features for this motherboard are implemented by cabling connectors on the

motherboard to indicators and switches or buttons on the chassis, make sure your chassis

supports all the features required.

• If there is a possibility of adopting some more hard drives, make sure your chassis has

sufficient power and space for them.

• Most chassis have alternatives for I/O shield located at the rear panel. Make sure the I/O

shield of the chassis matches the I/O port configuration of this motherboard. You can find

an I/O shield specifically designed for this motherboard in its package.

1.4 Installing Motherboard

Most computer chassis have a base with many

mounting holes to allow the motherboard to be

securely attached, and at the same time, prevent

the system from short circuits. There are two

ways to attach the motherboard to the chassis

base: (1) with studs, or (2) with spacers.

Basically, the best way to attach the board is

with studs. Only if you are unable to do this

should you attach the board with spacers. Line up the holes on the board with the mounting

holes on the chassis. If the holes line up and there are screw holes, you can attach the board

with studs. If the holes line up and there are only slots, you can only attach with spacers. Take

the tip of the spacers and insert them into the slots. After doing this to all the slots, you can

slide the board into position aligned with slots. After the board has been positioned, check to

make sure everything is OK before putting the chassis back on.

※ Always power off the computer and unplug the AC power cord before adding or

removing any peripheral or component. Failing to so may cause severe damage

to your motherboard and/or peripherals. Plug in the AC power cord only after

you have carefully checked everything.

To install this motherboard:

1. Locate all the screw holes on the

motherboard and the chassis base.

2. Place all the studs or spacers needed on

the chassis base and have them tightened.

3. Face the motherboard’s I/O ports toward

the chassis’s rear panel.

4. Line up all the motherboard’s screw holes

with those studs or spacers on the chassis.

5. Install the motherboard with screws and

have them tightened.

※ To prevent shorting the PCB circuit,

please REMOVE the metal studs or

spacers if they are already fastened

on the chassis base and are without

mounting-holes on the motherboard

to align with.

Face the chassis’s rear panel.

1-4 IN9 32X/IN9 32X -MAX

1.5 Checking Jumper Settings

• For a 2-pin jumper, plug the

jumper cap on both pins will

make it CLOSE (SHORT).

Remove the jumper cap, or

plug it on either pin

(reserved for future use) will

leave it at OPEN position.

SHORT OPEN

OPEN

• For 3-pin jumper, pin 1~2 or pin 2~3 can be

shorted by plugging the jumper cap in.

Pin 1~2 SHORT

Pin 2~3 SHORT

1.5.1 CMOS Memory Clearing Header and Backup Battery

The time to clear the CMOS memory occurs when (a)

the CMOS data becomes corrupted, (b) you forgot the

supervisor or user password preset in the BIOS menu,

(c) you are unable to boot-up the system because the

CPU ratio/clock was incorrectly set in the BIOS menu,

or (d) whenever there is modification on the CPU or

memory modules.

This header uses a jumper cap to clear the CMOS

memory and have it reconfigured to the default values

stored in BIOS.

• Pins 1 and 2 shorted

(Default): Normal

operation.

• Pins 2 and 3 shorted:

Clear CMOS memory.

To clear the CMOS memory and load in the default values:

1. Power off the system.

2. Set pin 2 and pin 3 shorted by the jumper cap. Wait for a few seconds. Set the jumper

cap back to its default settings --- pin 1 and pin 2 shorted.

3. Power on the system.

4. For incorrect CPU ratio/clock settings in the BIOS, press <Del> key to enter the BIOS

setup menu right after powering on system.

5. Set the CPU operating speed back to its default or an appropriate value.

6. Save and exit the BIOS setup menu.

※ Another easy way to clear the CMOS memory can be done by switching

“EZ-CCMOS1”, see the section of “Connecting Rear Panel I/O Devices” in this

manual for detail.

※ The C.C. POST Code appears when either the external “EZ-CCMOS1” switch or

the internal “CCMOS1” jumper is not set to its normal position.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-5

CMOS Backup Battery:

An onboard battery saves the CMOS memory to keep the BIOS information stays on even after

disconnected your system with power source. Nevertheless, this backup battery exhausts after

some five years. Once the error message like “CMOS BATTERY HAS FAILED” or “CMOS

checksum error” displays on monitor, this backup battery is no longer functional and has to

be renewed.

To renew the backup battery:

1. Power off the system and disconnect with AC power source.

2. Remove the exhausted battery.

3. Insert a new CR2032 or equivalent battery. Pay attention to its polarity. The “+” side is its

positive polarity.

4. Connect AC power source and power on the system.

5. Enter the BIOS setup menu. Reconfigure the setup parameters if necessary.

CAUTION:

※ Danger of explosion may arise if the battery is incorrectly renewed.

※ Renew only with the same or equivalent type recommended by the battery

manufacturer.

※ Dispose of used batteries according to the battery manufacturer’s instructions.

1-6 IN9 32X/IN9 32X -MAX

1.6 Connecting Chassis Components

1.6.1 ATX Power Connectors

These connectors provide the connection from an ATX power supply. As the plugs from the

power supply fit in only one orientation, find the correct one and push firmly down into these

connectors.

ATXPWR1: ATX 24-Pin Power Connector

The power supply with 20-pin or 24-pin cables can both be connected to this 24-pin connector.

Connect from pin-1 for either type. However, a 20-pin power supply may cause the system

unstable or even unbootable for the sake of insufficient electricity. A minimum power of 300W

or higher is recommended.

ATX12V1: ATX 12V 8-Pin Power Connector

This connector supplies power to CPU. The system will not start without connecting power to

this one.

ATX4P1: Auxiliary 12V Power Connector

This connector provides an auxiliary power source for devices added on PCI Express slots.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-7

1.6.2 Front Panel Switches & Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel.

Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure

below stands for positive polarity for the LED connection. Please pay attention when connecting

these headers. A wrong orientation will only result in the LED not lighting, but a wrong

connection of the switches could cause system malfunction.

• HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis front panel.

• RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis front panel.

• SPKR (Pin 13, 15, 17, 19):

Connects to the System Speaker cable of chassis.

• SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there is one) of chassis front panel.

• PWR (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

• PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

1-8 IN9 32X/IN9 32X -MAX

1.6.3 FAN Power Connectors

These connectors each provide power to the cooling fans installed in your system.

• CPUFAN1: CPU Fan Power Connector

• SYSFAN1: System Fan Power Connector

• AUXFAN1~4: Auxiliary Fan Power Connector

※ These fan connectors are not jumpers. DO NOT place jumper caps on these

connectors.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-9

1.6.4 Additional Cooling Fan for NB Heatsink

To attach an additional chipset cooling fan for model

“IN9 32X-MAX”

:

Inside the motherboard package you can find a pair of retention clips. These retention clips are

used to fasten an additional cooling-fan attached onto the north bridge heatsink to blow away

the heatwave radiated from the heatsink.

As shown in the photo, you will have to buy

an additional three-wire cooling fan in

40x40x10mm size: (You may have to

consider the wire length according to which

fan power connector you want to connect

to.)

1. Power off your system.

2. Put the fan with its airflow direction

down on the chipset heatsink.

3. Secure the retention clips.

Make sure

not to jam the fan blades.

4. Plug the fan power connector to the

three-pin SYSFAN or AUXFAN header.

5. Check to see the fan will not be jiggled. Now you have finished the attachment.

To attach an additional chipset cooling fan for model

“IN9 32X”

:

There are no retention clips provided. There are two screw-holes located at the bottom of the

NB heatsink for fan attachment.

As shown in the photo, you will have to buy

an additional three-wire cooling fan in

40x40x10mm size, and prepare two Machine

Screws (

Pan Head M3 x P0.5 x 10 mm)

for attachment: (You may have to consider

the wire length according to which fan power

connector you want to connect to.)

1. Power off your system. Remove the VGA

card if you had it already installed on slot

PCIEXP1.

2. Attach the fan to the NB heatsink, either

with its airflow direction toward or away

from the chipset heatsink.

3. Secure the fan with two screws. (Slot

PCIEXP1 might be in the way when

fastening the screw, please proceed with care.)

4. Plug the fan power connector to the three-pin SYSFAN or AUXFAN header.

5. Now you have finished the attachment.

1-10 IN9 32X/IN9 32X -MAX

1.7 Installing Hardware

※ DO NOT scratch the motherboard when installing hardware. An accidental

scratch of a tiny surface-mount component may seriously damage the

motherboard.

※ In order to protect the contact pins, please pay attention to these notices:

1. A maximum 20 cycles of CPU installation is recommended.

2. Never touch the contact pins with fingers or any object.

3. Always put on the cap when the CPU is not in use.

1.7.1 CPU Socket 775

※ The installation procedures vary with different types of CPU fan-and-heatsink

assembly. The one shown here is served for demo only. For detailed

information on how to install the one you bought, refer to its installation

guidelines.

1. Place the board so that the lever-hook of

the socket is on your left side. Use your left

thumb and forefinger to hold the lever hook,

pull it away from the retention tab. Rotate

the lever to fully open position.

2. Use your right-thumb to raise the load

plate. Lift it up to fully open position.

3. Use your right thumb and forefinger to

grasp the CPU package. Be sure to grasp on

the edge of the substrate, and face the Pin-1

indicator toward the bottom-left side. Aim at

the socket and place the CPU package

vertical down into the socket.

4. Visually inspect if the CPU is seated well

into the socket. The alignment key must be

located in the notch of package.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-11

5. Use your left hand to hold the load plate,

and use your right thumb to peel the cap off.

The cap plays an important role in

protecting contact pins. In order to

prevent bent pin, PUT ON the cap after

operation or testing.

6. Lower the plate onto the CPU package.

Engage the load lever while gently pressing

down the load plate.

7. Secure the lever with the hook under

retention tab.

8. Place the heatsink and fan assembly onto

the socket. Align the four fasteners toward

the four mounting holes on the motherboard.

9. Press each of the four fasteners down

into the mounting holes. Rotate the fastener

clock-wise to lock the heatsink and fan

assembly into position.

10. Attach the four-pin power plug from the

heatsink and fan assembly to the CPU FAN

connector.

※ A higher fan speed will be helpful for better airflow and heat-dissipation.

Nevertheless, stay alert to not touch any heatsink since a high temperature

generated by the working system is still possible.

1-12 IN9 32X/IN9 32X -MAX

1.7.2 DDR2 Memory Slots

• To reach the optimum performance in dual-channel configurations, install identical DDR2

DIMM pairs for each channel.

• Install DIMMs with the same CAS latency. To reach the optimum compatibility, obtain

memory modules from the same vendor.

※ Usually there is no hardware or BIOS setup required after adding or removing

memory modules, but you will have to clear the CMOS memory first if any

memory module related problem occurs.

To install system memory:

1. Power off the computer and unplug the

AC power cord before installing or

removing memory modules.

2. Locate the DIMM slot on the board.

3. Hold two edges of the DIMM module

carefully, keep away from touching its

connectors.

4. Align the notch key on the module with

the rib on the slot.

5. Firmly press the module into the slots until the ejector tabs at both sides of the slot

automatically snap into the mounting notch. Do not force the DIMM module in with extra

force as the DIMM module only fits in one direction.

6. To remove the DIMM modules, push the two ejector tabs on the slot outward

simultaneously, and then pull out the DIMM module.

※ Static electricity can damage the electronic components of the computer or

optional boards. Before starting these procedures, ensure that you are

discharged of static electricity by touching a grounded metal object briefly.

Hardware Setup

IN9 32X/IN9 32X-MAX 1-13

1.7.3 PCI Express X16 Add-on Slots (Install Graphics Card)

These slots support the connections of graphics cards that comply with PCI Express

specifications. This motherboard provides triple PCI-Express X16 slots:

One PCIE graphics card installation (Normal Mode):

Insert your PCIE graphics card into [PCIEXP1] (MASTER) slot.

※ The [PCIEXP3] slot supports up to X8 bandwidth only.

1-14 IN9 32X/IN9 32X -MAX

Two PCIE graphics cards installation (SLI Mode):

To install two SLI-ready graphics cards under SLI Mode, you will need to:

• Prepare two identical NVIDIA certified, SLI-ready PCI Express X16 graphics cards (the

same model from the same manufacturer).

• Make sure the graphics card driver supports the NVIDIA SLI technology. Download the

latest driver form NVIDIA website (

www.nvidia.com).

• Make sure your power supply unit is sufficient to provide the minimum power required.

※ The following illustration is served for DEMO only. All the devices, including the

motherboard, the graphics cards, the SLI Bridge Connector, or the SLI bracket,

may not be exactly the same type, shape, or model as the one you bought.

1. Insert two identical SLI-ready graphics

cards into both PCIEXP1 and PCIEXP2

slots.

※ The NVIDIA SLI technology

currently supports the Windows

XP operating system only.

2. Bridge connecting two graphics cards

with the “SLI Connector Card” (fit in

both directions).

Insert and secure the SLI supporting

bracket.

La pagina sta caricando ...

Abit IN9 32X Manuale utente

Questo manuale è adatto anche per

Abit IN9 32X Manuale utente

in altre lingue

Documenti correlati

Altri documenti