Cisco Systems Linksys WRT320N Manuale utente

USER GUIDE

Dual-Band Wireless-N

Gigabit Router

Model: WRT320N

UK

English

BR

Português do Brasil

DE

Deutsch

ES

Español

FR

Français

IT

Italiano

NL

Nederlands

RU

Русский

USER GUIDE

Dual-Band Wireless-N

Gigabit Router

Model: WRT320N

About This Guide

i

Dual-Band Wireless-N Gigabit Router

About This Guide

Icon Descriptions

While reading through the User Guide you may see

various icons that call attention to specific items. Below is

a description of these icons:

NOTE: This tick indicates that there is a note of

interest and is something that you should pay

special attention to while using the product.

WARNING: This exclamation point indicates

that there is a caution or warning and it is

something that could damage your property or

product.

WEB: This globe icon indicates a noteworthy

website address or email address.

Online Resources

Website addresses in this document are listed without

http:// in front of the address because most current web

browsers do not require it. If you use an older web browser,

you may have to add http:// in front of the web address.

Resource Website

Linksys www.linksys.com

Linksys International www.linksys.com/international

Glossary www.linksys.com/glossary

Network Security www.linksys.com/security

Copyright and Trademarks

Linksys, Cisco and the Cisco Logo

are registered trademarks or

trademarks of Cisco Systems, Inc.

and/or its affiliates in the U.S. and

certain other countries. Copyright

reserved. Other brands and product

names are trademarks or registered

trademarks of their respective

holders.

Table of Contents

ii

Dual-Band Wireless-N Gigabit Router

Chapter 1: Product Overview 4

Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Placement Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2: Wireless Security Checklist 6

General Network Security Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Additional Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3: Advanced Conguration 7

Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .20

Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .21

Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .21

Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Appendix A: Troubleshooting 29

Appendix B: Specications 30

Appendix C: Warranty Information 31

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Exclusions and Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Obtaining Warranty Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Table of Contents

iii

Dual-Band Wireless-N Gigabit Router

Appendix D: Regulatory Information 33

FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Safety Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Avis d’Industrie Canada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Wireless Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Avis de non-responsabilité concernant les appareils sans l . . . . . . . . . . . . . . . . . .34

Declaration of Conformity with Regard to EU Directive 1999/5/EC (R&TTE Directive) . .35

Wireless Equipment (Wireless-N/G/A/B Products) . . . . . . . . . . . . . . . . . . . . . . . . .36

CE Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

National Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Product Usage Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Technical Documents on www.linksys.com/international . . . . . . . . . . . . . . . . . . . .37

User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste

Electric and Electronic Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Appendix E: Software Licence Agreement 42

Software in Linksys Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Software Licences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Chapter 1

Product Overview

4

Dual-Band Wireless-N Gigabit Router

Chapter 1:

Product Overview

Thank you for choosing the Linksys Dual-band Wireless-N

Gigabit Router. The Router lets you access the Internet via

a wireless connection or through one of its four switched

ports. You can also use the Router to share resources, such

as computers. A variety of security features help to protect

your data and your privacy while online. Security features

include WPA2 security, a Stateful Packet Inspection (SPI)

firewall and NAT technology. Configuring the Router is

easy using the provided browser-based utility.

Front Panel

1, 2, 3, 4 (Green/Blue) These numbered LEDs,

corresponding with the numbered ports on the

Router's back panel, serve two purposes. The

LED is solidly lit when the Router is connected

to a device through that port. It flashes to

indicates network activity. Green indicates

Gigabit speeds, and blue indicates 10/100

speeds.

Wi-Fi Protected Setup Button If you have

client devices, such as wireless adapters, that

support Wi-Fi Protected Setup, then you can

use Wi-Fi Protected Setup to automatically

configure wireless security for your wireless

network(s).

To use Wi-Fi Protected Setup, run the Setup

Wizard, or refer to the "Wireless > Basic Wireless

Settings" section of "Chapter 3: Advanced

Configuration".

Wi-Fi Protected Setup LED (Blue/Amber)

It lights up blue when wireless security is

enabled. The LED flashes blue for two minutes

during Wi-Fi Protected Setup.

The LED lights up amber if there is an error

during the Wi-Fi Protected Setup process. Make

sure the client device supports Wi-Fi Protected

Setup. Wait until the LED is off, and then try again.

The LED flashes amber when a Wi-Fi Protected

Setup session is active, and a second session

begins. The Router supports one session at a

time. Wait until the LED is off before starting the

next Wi-Fi Protected Setup session.

Wireless (Blue) The Wireless LED lights up

when the wireless feature is enabled. If the LED

is flashing, the Router is actively sending or

receiving data over the network.

Internet (Blue) The Internet LED lights up

when there is a connection made through the

Internet port. A flashing LED indicates network

activity over the Internet port.

Power (Blue) The Power LED lights up and will

stay on while the Router is powered on. When

the Router goes through its self-diagnostic

mode during every boot-up, this LED will flash.

When the diagnostic is complete, the LED will

be solidly lit.

Back Panel

Internet This Gigabit port is where you will

connect your cable or DSL Internet connection.

1, 2, 3, 4 These Gigabit ports (1, 2, 3, 4) connect

the Router to computers and other Ethernet

network devices on your wired network.

Reset There are two ways to reset the Router's

factory defaults. Either press and hold the Reset

Button for approximately five seconds, or restore

the defaults from Administration > Factory

Defaults in the Router's web-based utility.

Power The Power port is where you will

connect the power adapter.

Placement Positions

There are two ways to physically install the Router. The

first way is to place the Router horizontally on a surface.

The second way is to mount the Router on a wall.

Horizontal Placement

The Router has four rubber feet on its bottom panel. Place

the Router on a level surface near an electrical socket.

Chapter 1

Product Overview

5

Dual-Band Wireless-N Gigabit Router

Wall-Mounting Placement

The Router has two wall-mount slots on its bottom

panel. The distance between the slots is 152 mm

(6 inches).

Two screws are needed to mount the Router.

Suggested Mounting Hardware

2.5–3.0 mm

4–5 mm 1–1.5 mm

Note: Mounting hardware illustrations are not †

true to scale.

NOTE: Linksys is not responsible for damages

incurred by insecure wall-mounting hardware.

Follow these instructions:

Determine where you want to mount the Router. 1.

Make sure that the wall you use is smooth, flat, dry and

sturdy. Also make sure the location is within reach of

an electrical socket.

Drill two holes into the wall. Make sure the holes are 2.

152 mm (6 inches) apart.

Insert a screw into each hole and leave 3 mm 3.

(0.12 inches) of its head exposed.

Manoeuvre the Router so the wall-mount slots line up 4.

with the two screws.

Place the wall-mount slots over the screws and slide 5.

the Router down until the screws fit snugly into the

wall-mount slots.

152 mm

Wall Mounting Template

Print this page at 100% size.

Cut along the dotted line, and place on the wall to drill precise spacing.

Chapter 2

Wireless Security Checklist

6

Dual-Band Wireless-N Gigabit Router

Chapter 2:

Wireless Security Checklist

Wireless networks are convenient and easy to install, so

homes with high-speed Internet access are adopting them

at a rapid pace. Because wireless networking operates by

sending information over radio waves, it can be more

vulnerable to intruders than a traditional wired network.

Like signals from your mobile or cordless phones, signals

from your wireless network can also be intercepted. Since

you cannot physically prevent someone from connecting

to your wireless network, you need to take some additional

steps to keep your network secure.

1. Change the default wireless

network name or SSID

Wireless devices have a default wireless network name

or Service Set Identifier (SSID) set by the factory. This

is the name of your wireless network, and can be up to

32 characters in length. Linksys wireless products use

linksys as the default wireless network name. You should

change the wireless network name to something unique

to distinguish your wireless network from other wireless

networks that may exist around you, but do not use

personal information (such as your National Insurance

Number) because this information may be available for

anyone to see when browsing for wireless networks.

2. Change the default password

For wireless products such as access points and routers,

you will be asked for a password when you want to change

their settings. These devices have a default password set

by the factory. The Linksys default password is admin.

Hackers know these defaults and may try to use them

to access your wireless device and change your network

settings. To thwart any unauthorised changes, customise

the device's password so it will be hard to guess.

3. Enable MAC address filtering

Linksys routers give you the ability to enable Media Access

Control (MAC) address filtering. The MAC address is a

unique series of numbers and letters assigned to every

networking device. With MAC address filtering enabled,

wireless network access is provided solely for wireless

devices with specific MAC addresses. For example, you can

specify the MAC address of each computer in your home

so that only those computers can access your wireless

network.

4. Enable encryption

Encryption protects data transmitted over a wireless

network. Wi-Fi Protected Access (WPA/WPA2) and Wired

Equivalency Privacy (WEP) offer different levels of security

for wireless communication.

A network encrypted with WPA/WPA2 is more secure

than a network encrypted with WEP, because WPA/WPA2

uses dynamic key encryption. To protect the information

as it passes over the airwaves, you should enable the

highest level of encryption supported by your network

equipment.

WEP is an older encryption standard and may be the

only option available on some older devices that do not

support WPA.

General Network Security Guidelines

Wireless network security is useless if the underlying

network is not secure.

Password protect all computers on the network and •

individually password protect sensitive files.

Change passwords on a regular basis. •

Install anti-virus software and personal firewall •

software.

Disable file sharing (peer-to-peer). Some applications •

may open file sharing without your consent and/or

knowledge.

Additional Security Tips

Keep wireless routers, access points or gateways away •

from exterior walls and windows.

Turn wireless routers, access points or gateways •

off when they are not being used (at night, during

holidays).

Use strong passphrases that are at least eight characters •

in length. Combine letters and numbers to avoid using

standard words that can be found in the dictionary.

WEB: For more information on wireless

security, visit www.linksys.com/security

Chapter 3

Advanced Configuration

7

Dual-Band Wireless-N Gigabit Router

Chapter 3:

Advanced Configuration

After setting up the Router with the Setup Wizard (located

on the CD-ROM), the Router will be ready for use. However,

if you'd like to change its advanced settings, use the

Router's web-based utility. This chapter describes each

web page of the utility and each page's key functions. You

can access the utility via a web browser on a computer

connected to the Router.

The web-based utility has these main tabs: Setup,

Wireless, Security, Access Restrictions, Applications &

Gaming, Administration and Status. Additional tabs will

be available after you click one of the main tabs.

NOTE: When first installing the Router, you

should use the Setup Wizard on the Setup

CD-ROM. If you want to configure advanced

settings, use this chapter to learn about the

web-based utility.

How to access the Web-Based Utility

To access the web-based utility, launch the web browser on

your computer and enter the Router's default IP address,

192.168.1.1, in the Address field. Then, press Enter.

A login screen will appear. (Non-Windows XP users will

see a similar screen). Leave the User name field blank. The

first time you open the Web-based utility, use the default

password admin. (You can set a new password from the

Administration tab's Management screen). Click OK to

continue.

Login Screen

Setup > Basic Setup

The first screen that appears is the Basic Setup screen. This

allows you to change the Router's general settings.

Setup > Basic Setup

Internet Setup

The Internet Setup section configures the Router to your

Internet connection. Most of this information can be

obtained through your ISP.

Internet Connection Type

Select the type of Internet connection your ISP provides

from the drop-down menu. These are the available types:

Automatic Configuration - DHCP •

Static IP •

PPPoE •

PPTP •

L2TP •

Telstra Cable •

Automatic Configuration - DHCP

By default, the Router's Internet Connection Type is set

to Automatic Configuration - DHCP, which should be

kept only if your ISP supports DHCP or you are connecting

through a dynamic IP address. (This option usually applies

to cable connections).

Internet Connection Type > Automatic Configuration - DHCP

Chapter 3

Advanced Configuration

8

Dual-Band Wireless-N Gigabit Router

Static IP

If you are required to use a permanent IP address to

connect to the Internet, select Static IP.

Internet Connection Type > Static IP

Internet IP Address This is the Router's IP address, when

seen from the Internet. Your ISP will provide you with the

IP Address you need to specify here.

Subnet Mask This is the Router's Subnet Mask, as seen

by users on the Internet (including your ISP). Your ISP will

provide you with the Subnet Mask.

Default Gateway Your ISP will provide you with the IP

address of the ISP server.

DNS 1-3 Your ISP will provide you with at least one DNS

(Domain Name System) server IP address.

PPPoE

Some DSL-based ISPs use PPPoE (Point-to-Point Protocol

over Ethernet) to establish Internet connections. If you are

connected to the Internet through a DSL line, check with

your ISP to see if they use PPPoE. If they do, you will have

to enable PPPoE.

Internet Connection Type > PPPoE

Username and Password Enter the Username and

Password provided by your ISP.

Service Name If provided by your ISP, enter the Service

Name.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to elapse before

your Internet connection terminates. The default Max Idle

Time is 15 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

PPTP

Point-to-Point Tunneling Protocol (PPTP) is a service that

applies to connections in Europe only.

Internet Connection Type > PPTP

If your ISP supports DHCP or you are connecting through

a dynamic IP address, then select Obtain an IP Address

Automatically. If you are required to use a permanent IP

address to connect to the Internet, then select Specify an

IP Address. Then configure the following:

Specify an IP Address • This is the Router's IP address,

as seen from the Internet. Your ISP will provide you

with the IP Address you need to specify here.

Subnet Mask • This is the Router's Subnet Mask, as

seen by users on the Internet (including your ISP). Your

ISP will provide you with the Subnet Mask.

Default Gateway • Your ISP will provide you with the

IP address of the ISP server.

DNS 1-3 • Your ISP will provide you with at least one

DNS (Domain Name System) server IP address.

PPTP Server IP Address Your ISP will provide you with

the IP address of the PPTP server.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

Chapter 3

Advanced Configuration

9

Dual-Band Wireless-N Gigabit Router

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to elapse before

your Internet connection terminates. The default Max Idle

Time is 15 minutes.

Keep Alive: Redial Period

If you select this option, the

Router will periodically check your Internet connection. If

you are disconnected, then the Router will automatically

re-establish your connection. To use this option, select

Keep Alive. In the Redial Period field, you specify how often

you want the Router to check the Internet connection. The

default value is 30 seconds.

L2TP

L2TP is a service that applies to connections in Israel only.

Internet Connection Type > L2TP

Server IP Address This is the IP address of the L2TP

Server. Your ISP will provide you with the IP Address you

need to specify here.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to elapse before

your Internet connection terminates. The default Max Idle

Time is 15 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

Telstra Cable

Telstra Cable is a service that applies to connections in

Australia only.

Internet Connection Type > Telstra Cable

Server IP Address This is the IP address of the Heartbeat

Server. Your ISP will provide you with the IP Address you

need to specify here.

Username and Password Enter the Username and

Password provided by your ISP.

Connect on Demand: Max Idle Time You can configure

the Router to cut the Internet connection after it has been

inactive for a specified period of time (Max Idle Time). If

your Internet connection has been terminated due to

inactivity, Connect on Demand enables the Router to

automatically re-establish your connection as soon as you

attempt to access the Internet again. To use this option,

select Connect on Demand. In the Max Idle Time field,

enter the number of minutes you want to elapse before

your Internet connection terminates. The default Max Idle

Time is 15 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify

with your ISP before making any changes.

Optional Settings

Host Name and Domain Name These fields allow you to

supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your

broadband Internet service has been configured with a

host and domain name. In most cases, leaving these fields

blank will work.

Chapter 3

Advanced Configuration

10

Dual-Band Wireless-N Gigabit Router

MTU MTU is the Maximum Transmission Unit. It specifies

the largest packet size permitted for Internet transmission.

Select Manual if you want to manually enter the largest

packet size that is transmitted. To have the Router select

the best MTU for your Internet connection, keep the

default setting, Auto.

Size When Manual is selected in the MTU field, this option

is enabled. Leave this value in the 1200 to 1500 range. The

default size depends on the Internet Connection Type:

DHCP, Static IP or Telstra: • 1500

PPPoE: • 1492

PPTP or L2TP: • 1460

Network Setup

The Network Setup section changes the settings on the

network connected to the Router's Ethernet ports. Wireless

setup is performed through the Wireless tab.

Router IP

This presents both the Router's IP Address and Subnet

Mask as seen by your network.

Router IP

DHCP Server Setting

The settings allow you to configure the Router's Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each

computer on your network. If you choose to enable the

Router's DHCP server option, make sure there is no other

DHCP server on your network.

DHCP Server Setting

DHCP Server DHCP is enabled by factory default. If you

already have a DHCP server on your network or you don't

want a DHCP server, then select Disabled (no other DHCP

features will be available).

DHCP Reservation Click this button if you want to assign

a fixed local IP address to a MAC address.

DHCP Reservation

You will see a list of DHCP clients with the following

information: Client Name, Interface, IP Address and

MAC Address.

DHCP Reservation

Select Clients from DHCP Table • Click the Select tick

box to reserve a client's IP address. Then click Add

Clients.

Manually Adding Client • To manually assign an IP

address, enter the client's name in the Enter Client

Name field. Enter the IP address you want it to have in

the Assign IP Address field. Enter its MAC address in the

To This MAC Address field. Then click Add.

Clients Already Reserved

A list of DHCP clients and their fixed local IP addresses

will be displayed at the bottom of the screen. If you

want to remove a client from this list, click Remove.

Click Save Settings to apply your changes or click

Cancel Changes to cancel your changes. To view the

most up-to-date information, click Refresh. To exit this

screen, click Close.

Start IP Address Enter a value for the DHCP server to

start with when is

suing IP addresses. Because the Router's

default IP address is 192.168.1.1, the Start IP Address must

be 192.168.1.2 or greater, but smaller than 192.168.1.253.

The default Starting IP Address is 192.168.1.100

.

Maximum Number of Users Enter the maximum

number of PCs that you want the DHCP server to assign

IP addresses to. This number cannot be greater than 253.

The default is 50.

IP Address Range Displayed here is the range of available

IP addresses.

Chapter 3

Advanced Configuration

11

Dual-Band Wireless-N Gigabit Router

Client Lease Time The Client Lease Time is the amount

of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the

amount of time, in minutes, that the user will be "leased"

this dynamic IP address. After the time is up, the user will

be automatically assigned a new dynamic IP address. The

default is 0 minutes, which means one day.

Static DNS 1-3

The Domain Name System (DNS) is how

the Internet translates domain or website names into

Internet addresses or URLs. Your ISP will provide you with at

least one DNS Server IP Address. If you wish to use another,

enter that IP Address in one of these fields. You can enter up

to three DNS Server IP Addresses here. The Router will use

these for quicker access to functioning DNS servers

.

WINS The Windows Internet Naming Service (WINS)

manages each PC's interaction with the Internet. If you

use a WINS server, enter that server's IP Address here.

Otherwise, leave this blank.

Time Setting

Time Zone Select the time zone in which your network

functions from this drop-down menu. (You can even

automatically adjust for daylight saving time).

Time Setting

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Setup > DDNS

The Router offers a Dynamic Domain Name System (DDNS)

feature. DDNS lets you assign a fixed host and domain

name to a dynamic Internet IP address. It is useful when

you are hosting your own website, FTP server or other

server behind the Router.

Before you can use this feature, you need to sign

up for DDNS service with a DDNS service provider,

www.dyndns.org or www.TZO.com. If you do not want to

use this feature, keep the default setting, Disabled.

DDNS

DDNS Service

If your DDNS service is provided by DynDNS.org, then

select DynDNS.org from the drop-down menu. If your

DDNS service is provided by TZO, then select TZO.com.

The features available on the DDNS screen will vary,

depending on which DDNS service provider you use.

DynDNS.org

Setup > DDNS > DynDNS

Username Enter the Username for your DDNS account.

Password Enter the Password for your DDNS account.

Host Name The is the DDNS URL assigned by the DDNS

service.

System Select the DynDNS service you use: Dynamic,

Static or Custom. The default selection is Dynamic.

Mail Exchange (Optional) Enter the address of your mail

exchange server, so emails to your DynDNS address go to

your mail server.

Backup MX This feature allows the mail exchange server

to be a backup. To disable this feature, keep the default,

Disabled. To enable the feature, select Enabled. If you

are not sure which setting to select, keep the default,

Disabled.

Wildcard This setting enables or disables wildcards

for your host. For example, if your DDNS address is

myplace.dyndns.org and you enable wildcards, then

x.myplace.dyndns.org will work as well (x is the wildcard).

To disable wildcards, keep the default, Disabled. To enable

wildcards, select Enabled. If you are not sure which setting

to select, keep the default, Disabled.

Internet IP Address The Router's Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Update To manually trigger an update, click this button.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Chapter 3

Advanced Configuration

12

Dual-Band Wireless-N Gigabit Router

TZO.com

Setup > DDNS > TZO

E-mail Address, TZO Key and Domain Name Enter the

settings of the account you set up with TZO.

Internet IP Address The Router's Internet IP address is

displayed here. Because it is dynamic, it will change.

Status The status of the DDNS service connection is

displayed here.

Update To manually trigger an update, click this button.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Setup > MAC Address Clone

A MAC address is a 12-digit code assigned to a unique

piece of hardware for identification. Some ISPs will require

you to register a MAC address in order to access the

Internet. If you do not wish to re-register the MAC address

with your ISP, you may assign the MAC address you have

currently registered with your ISP to the Router with the

MAC Address Clone feature.

Setup > MAC Address Clone

MAC Address Clone

Enabled/Disabled To have the MAC Address cloned,

select Enabled.

MAC Address Enter the MAC Address registered with

your ISP here.

Clone My PC's MAC Click this button to clone the MAC

address of the computer you are using.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Setup > Advanced Routing

This screen is used to set up the Router's advanced

functions. Operating Mode allows you to select the

type(s) of advanced functions you use. Dynamic Routing

automatically adjusts how packets travel on your network.

Static Routing sets up a fixed route to another network

destination.

Setup > Advanced Routing

Advanced Routing

NAT

Enabled/Disabled If this Router is hosting your network's

connection to the Internet, keep the default, Enabled. If

another router exists on your network, select Disabled.

When the NAT setting is disabled, dynamic routing will be

enabled.

Dynamic Routing (RIP)

Enabled/Disabled This feature enables the Router to

automatically adjust to physical changes in the network's

layout and exchange routing tables with the other router(s).

The Router determines the network packets' route based

on the fewest number of hops between the source and

the destination. When the NAT setting is enabled, the

Dynamic Routing feature is automatically disabled. When

the NAT setting is disabled, this feature is available. Select

Enabled to use the Dynamic Routing feature.

Static Routing

A static route is a pre-determined pathway that network

information must travel to reach a specific host or network.

Enter the information described below to set up a new

static route.

Chapter 3

Advanced Configuration

13

Dual-Band Wireless-N Gigabit Router

Route Entries To set up a static route between the Router

and another network, select a number from the drop-

down list. Click Delete This Entry to delete a static route.

Enter Route Name Enter a name for the Route here,

using a maximum of 25 alphanumeric characters.

Destination LAN IP The Destination LAN IP is the address

of the remote network or host to which you want to assign

a static route.

Subnet Mask The Subnet Mask determines which portion

of a Destination LAN IP address is the network portion and

which portion is the host portion.

Gateway This is the IP address of the gateway device that

allows for contact between the Router and the remote

network or host.

Interface This interface tells you whether the Destination

IP Address is on the LAN & Wireless (Ethernet and wireless

networks) or the WAN (Internet).

Click Show Routing Table to view the static routes you

have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway and Interface are displayed. Click

Refresh to update the information. Click Close to exit

this screen.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this

screen.

There are two ways to configure the Router's wireless

network(s), manual and Wi-Fi Protected Setup.

Wi-Fi Protected Setup is a feature that makes it easy to set

up your wireless network. If you have client devices, such

as wireless adapters, that support Wi-Fi Protected Setup,

then you can use Wi-Fi Protected Setup.

Configuration View To manually configure your wireless

network, select Manual. Proceed to the "Basic Wireless

Settings" section. To use Wi-Fi Protected Setup, select

Wi-Fi Protected Setup. Proceed to the "Wi-Fi Protected

Setup" section.

Basic Wireless Settings

Wireless > Basic Wireless Settings (Manual Setup)

Wireless Band This is used to select the 2.4 GHz or

5.0 GHz band.

Network Mode From this drop-down menu, you can

select the wireless standards running on your network. If

you have Wireless-N, Wireless-G and Wireless-B devices in

your network, keep the default setting, Mixed. If you have

only Wireless-G and Wireless-B devices in your network,

select BG-Mixed. If you have only Wireless-N devices,

select Wireless-N Only. If you have only Wireless-G

devices, select Wireless-G Only. If you have only Wireless-B

devices, select Wireless-B Only. If you do not have any

wireless devices in your network, select Disabled.

Network Name (SSID) The SSID is the network name

shared among all points in a wireless network. The

SSID must be identical for all devices in the wireless

network. It is case-sensitive and must not exceed

32 characters (use any of the characters on the keyboard).

Make sure this setting is the same for all points in your

wireless network. For added security, you should change

the default SSID (linksys) to a unique name.

Channel Width Select Auto if you want the Router

to automatically determine the proper channel width

(20 MHz or 40 MHz) to use or select 20 MHz only (default)

if you want the Router to operate in Wireless-B and

Wireless-G mode only. For best performance, Auto is

recommended.

Wide Channel If you selected Wide - 40MHz Channel for

the Radio Band setting, then this setting will be available

for your primary Wireless-N channel. Select any channel

from the drop-down menu. If you are not sure which

channel to select, keep the default, Auto.

Channel Select a channel from 1 to 11 or Auto (default).

SSID Broadcast When wireless clients survey the local

area for wireless networks to associate with, they will

detect the SSID broadcast by the Router. To broadcast the

Chapter 3

Advanced Configuration

14

Dual-Band Wireless-N Gigabit Router

Router's SSID, keep the default setting, Enabled. If you

do not want to broadcast the Router's SSID, then select

Disabled.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Wi-Fi Protected Setup

There are three methods available. Use the method that

applies to the client device you are configuring.

Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)

NOTE: Wi-Fi Protected Setup configures one

client device at a time. Repeat the instructions

for each client device that supports Wi-Fi

Protected Setup.

Method #1

Use this method if your client device has a Wi-Fi Protected

Setup button.

Click or press the1. Wi-Fi Protected Setup button on

the client device.

Click the 2. Wi-Fi Protected Setup button on this

screen.

After the client device has been configured, click 3.

OK. Then refer back to your client device or its

documentation for further instructions.

Method #2

Use this method if your client device has a Wi-Fi Protected

Setup PIN number.

Enter the PIN number in the1. field on this screen.

Click 2. Register.

After the client device has been configured, click 3.

OK. Then refer back to your client device or its

documentation for further instructions.

Method #3

Use this method if your client device asks for the Router's

PIN number.

Enter the PIN number listed on this screen. (It is also 1.

listed on the label on the bottom of the Router).

After the client device has been configured, click 2.

OK. Then refer back to your client device or its

documentation for further instructions.

The Wi-Fi Protected Setup Status, Network Name (SSID),

Security, Encryption and Passphrase are displayed at the

bottom of the screen.

NOTE: If you have client devices that do not

support Wi-Fi Protected Setup, note the wireless

settings and then manually configure those

client devices.

Wireless > Wireless Security

The Wireless Security screen configures the security of

your wireless network. There are six wireless security

mode options supported by the Router: WPA Personal,

WPA Enterprise, WPA2 Personal, WPA2 Enterprise, RADIUS

and WEP. (WPA stands for Wi-Fi Protected Access, which

is a security standard stronger than WEP encryption. WEP

stands for Wired Equivalent Privacy, while RADIUS stands

for Remote Authentication Dial-In User Service). These

six are briefly discussed here. For detailed instructions

on configuring wireless security for the Router, refer to

"Chapter 2: Wireless Security."

Wireless Security

Security Mode

Select the security method for your wireless network. If

you do not want to use wireless security, keep the default,

Disabled.

WPA Personal

NOTE: If you are using WPA, always remember

that each device in your wireless network MUST

use the same WPA method and shared key or

else the network will not function properly.

Chapter 3

Advanced Configuration

15

Dual-Band Wireless-N Gigabit Router

Security Mode > WPA Personal

Passphrase Enter a Passphrase of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys.

The default Group Key Renewal period is 3600 seconds.

WPA2 Personal

Security Mode > WPA2 Personal

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the

type of algorithm, AES or TKIP or AES. The default is TKIP

or AES.

Passphrase Enter a Passphrase of 8-63 characters.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption keys.

The default Group Key Renewal period is 3600 seconds.

WPA Enterprise

This option features WPA used in co-ordination with a

RADIUS server. (This should only be used when a RADIUS

server is connected to the Router).

Security Mode > WPA Enterprise

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption

keys. The default Key Renewal period is 3600 seconds.

WPA2 Enterprise

This option features WPA2 used in co-ordination with a

RADIUS server. (This should only be used when a RADIUS

server is connected to the Router).

Security Mode > WPA2 Enterprise

Encryption WPA2 supports two encryption methods,

TKIP and AES, with dynamic encryption keys. Select the

type of algorithm, AES or TKIP or AES. The default is TKIP

or AES.

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Chapter 3

Advanced Configuration

16

Dual-Band Wireless-N Gigabit Router

Key Renewal Enter a Key Renewal period, which instructs

the Router how often it should change the encryption

keys. The default Key Renewal period is 3600 seconds.

RADIUS

This option features WEP used in co-ordination with a

RADIUS server. (This should only be used when a RADIUS

server is connected to the Router).

Security Mode > RADIUS

IMPORTANT: If you are using WEP encryption,

always remember that each device in your

wireless network MUST use the same WEP

encryption method and encryption key or else

your wireless network will not function properly.

RADIUS Server Enter the IP Address of the RADIUS

server.

RADIUS Port Enter the port number of the RADIUS

server. The default value is 1812.

Shared Secret Enter the key shared between the Router

and the server.

Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits).

The default is 40/64 bits (10 hex digits).

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate.

Key 1 If you did not enter a Passphrase, enter the WEP

key manually.

WEP

WEP is a basic encryption method, which is not as secure

as WPA.

Security Mode > WEP

Encryption Select a level of WEP encryption,

40/64 bits (10 hex digits) or 104/128 bits (26 hex digits).

The default is 40/64 bits (10 hex digits).

Passphrase Enter a Passphrase to automatically generate

WEP keys. Then click Generate.

Key 1 If you did not enter a Passphrase, enter the WEP

key manually.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Wireless > Wireless MAC Filter

Wireless access can be filtered by using the MAC addresses of

the wireless devices transmitting within your network's radius.

Wireless > Wireless MAC Filter

Chapter 3

Advanced Configuration

17

Dual-Band Wireless-N Gigabit Router

Wireless MAC Filter

Enabled/Disabled

To filter wireless users by MAC Address,

either permitting or blocking access, select Enabled. If you

do not wish to filter users by MAC Address, keep the default

setting, Disabled

.

Access Restriction

Prevent Select this to block wireless access by MAC

Address. This option is selected by default.

Permit Select this to allow wireless access by MAC

Address. This option is not selected by default.

MAC Address Filter List

Wireless Client List Click this to open the Wireless Client

List screen.

Wireless Client List

This screen shows computers and other devices on

the wireless network. The list can be sorted by Client

Name, Interface, IP Address, MAC Address and Status.

Select Save to MAC Address Filter List for any device

you want to add to the MAC Address Filter List. Then

click Add.

To retrieve the most up-to-date information, click

Refresh. To exit this screen and return to the Wireless

MAC Filter screen, click Close.

MAC 01-50 Enter the MAC addresses of the devices

whose wireless access you want to block or allow.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Wireless > Advanced Wireless Settings

This Advanced Wireless Settings screen is used to set up

the Router's advanced wireless functions. These settings

should only be adjusted by an expert administrator as

incorrect settings can reduce wireless performance.

Wireless > Advanced Wireless Settings

Advanced Wireless

AP Isolation This isolates all wireless clients and wireless

devices on your network from each other. Wireless devices

will be able to communicate with the Router but not

with each other. To use this function, select Enabled. AP

Isolation is disabled by default.

Frame Burst Enabling this option should provide your

network with greater performance, depending on the

manufacturer of your wireless products. To use this option,

keep the default Enabled. Otherwise, select Disabled.

Authentication Type The default is set to Auto, which

allows either Open System or Shared Key authentication

to be used. With Open System authentication, the sender

and the recipient do NOT use a WEP key for authentication.

With Shared Key authentication, the sender and recipient

use a WEP key for authentication. Select Shared Key to

only use Shared Key authentication.

Basic Rate The Basic Rate setting is not actually one rate

of transmission but a series of rates at which the Router

can transmit. The Router will advertise its Basic Rate to the

other wireless devices in your network, so they know which

rates will be used. The Router will also advertise that it will

automatically select the best rate for transmission. The

default setting is Default, when the Router can transmit

at all standard wireless rates (1-2Mbps, 5.5Mbps, 11Mbps,

18Mbps and 24Mbps). Other options are 1-2Mbps, for

use with older wireless technology and All, when the

Router can transmit at all wireless rates. The Basic Rate

is not the actual rate of data transmission. If you want to

specify the Router's rate of data transmission, configure

the Transmission Rate setting.

Transmission Rate The rate of data transmission should

be set depending on the speed of your wireless network.

You can select from a range of transmission speeds or you

can select Auto to have the Router automatically use the

fastest possible data rate and enable the Auto-Fallback

feature. Auto-Fallback will negotiate the best possible

Chapter 3

Advanced Configuration

18

Dual-Band Wireless-N Gigabit Router

connection speed between the Router and a wireless

client. The default is Auto.

N Transmission Rate The rate of data transmission

should be set depending on the speed of your Wireless-N

networking. You can select from a range of transmission

speeds or you can select Auto to have the Router

automatically use the fastest possible data rate and enable

the Auto-Fallback feature. Auto-Fallback will negotiate the

best possible connection speed between the Router and a

wireless client. The default is Auto.

CTS Protection Mode The Router will automatically

use CTS (Clear-To-Send) Protection Mode when your

Wireless-N and Wireless-G products are experiencing

severe problems and are not able to transmit to the

Router in an environment with heavy 802.11b traffic. This

function boosts the Router's ability to catch all Wireless-N

and Wireless-G transmissions but will severely decrease

performance. The default is Auto.

Beacon Interval Enter a value between 1 and 65,535

milliseconds. The Beacon Interval value indicates the

frequency interval of the beacon. A beacon is a packet

broadcast by the Router to synchronise the wireless

network. The default value is 100.

DTIM Interval This value, between 1 and 255, indicates

the interval of the Delivery Traffic Indication Message

(DTIM). A DTIM field is a countdown field informing

clients of the next window for listening to broadcast

and multicast messages. When the Router has buffered

broadcast or multicast messages for associated clients, it

sends the next DTIM with a DTIM Interval value. Its clients

hear the beacons and awaken to receive the broadcast

and multicast messages. The default value is 1.

Fragmentation Threshold This value specifies the

maximum size for a packet before data is fragmented

into multiple packets. If you experience a high packet

error rate, you may slightly increase the Fragmentation

Threshold. Setting the Fragmentation Threshold too low

may result in poor network performance. Only minor

reduction of the default value is recommended. In most

cases, it should remain at its default value of 2346.

RTS Threshold Should you encounter inconsistent data

flow, only a minor reduction of the default value, 2347,

is recommended. If a network packet is smaller than the

preset RTS threshold size, the RTS/CTS mechanism will

not be enabled. The Router sends Request to Send (RTS)

frames to a particular receiving station and negotiates

the sending of a data frame. After receiving an RTS, the

wireless station responds with a Clear to Send (CTS) frame

to acknowledge the right to begin transmission. The RTS

Threshold value should remain at its default value of

2347.

Click Save Settings to apply your changes or click Cancel

Changes to cancel your changes.

Security > Firewall

The Firewall screen is used to configure a firewall that can

filter out various types of unwanted traffic on the Router's

local network.

Security > Firewall

Firewall

SPI Firewall Protection To use firewall protection,

keep the default selection, Enabled. To turn off firewall

protection, select Disabled.

Internet Filter

Filter Anonymous Internet Requests This feature

makes it more difficult for outside users to work their

way into your network. This feature is selected by default.

Deselect the feature to allow anonymous Internet

requests

.

Filter Multicast Multicasting allows for multiple

transmissions to specific recipients at the same time. If

multicasting is permitted, then the Router will allow IP

multicast packets to be forwarded to the appropriate

computers. Select this feature to filter multicasting. This

feature is not selected by default.

Filter Internet NAT Redirection This feature uses port

forwarding to block access to local servers from local

networked computers. Select this feature to filter Internet

NAT redirection. It is not selected by default.

Filter IDENT (Port 113) This feature keeps port 113 from

being scanned by devices outside of your local network.

This feature is selected by default. Deselect this feature to

disable it.

Web Filter

Proxy Use of WAN proxy servers may compromise the

Gateway's security. Denying Proxy will disable access to

any WAN proxy servers. Select this feature to enable proxy

filtering. Deselect the feature to allow proxy access

.

Java Java is a programming language for websites. If you

deny Java, you run the risk of not having access to Internet

La pagina sta caricando ...

Cisco Systems Linksys WRT320N Manuale utente

Questo manuale è adatto anche per

Cisco Systems Linksys WRT320N Manuale utente

in altre lingue

Altri documenti