Linksys WAG200G Manuale utente

A Division of Cisco Systems, Inc.

®

Model No.

ADSL Home Gateway

Wireless-G

WAG354G (EU)

User Guide

WIRELESS

GHz

802.11g

2,4

Wireless-G ADSL Home Gateway

Copyright and Trademarks

Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco

rights reserved. Other brands and product names are trademarks or registered trademarks of their respective

holders.

How to Use this Guide

Your Guide to the Wireless-G ADSL Home Gateway has been designed to make understanding networking with

the Gateway easier than ever. Look for the following items when reading this User Guide:

In addition to these symbols, there are definitions for technical terms that are presented like this:

Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like

this:

Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.

This exclamation point means there is a Caution or

Warning and is something that could damage your

property or the Gateway.

word: definition.

This checkmark means there is a Note of interest and

is something you should pay special attention to while

using the Gateway.

This question mark provides you with a reminder about

something you might need to do while using the Gateway.

Figure 0-1: Sample Figure Description

WAG354G-EU-UG-50429C JL

Wireless-G ADSL Home Gateway

Table of Contents

Chapter 1: Introduction 1

Welcome 1

What’s in this User Guide? 2

Chapter 2: Planning Your Network 4

The Gateway’s Functions 4

IP Addresses 4

Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway 6

Ports and Reset Button on Side Panel 6

LEDs on Side Panel 7

The Top Panel 8

The Bottom Panel 9

Chapter 4: Connecting the Wireless-G ADSL Home Gateway 10

Overview 10

Wired Connection to a Computer 11

Wireless Connection to a Computer 12

Chapter 5: Configuring the Wireless-G ADSL Home Gateway 13

Overview 13

How to Access the Web-based Utility 15

The Setup Tab 15

The Wireless Tab 23

The Security Tab 28

The Access Restrictions Tab 30

The Applications and Gaming Tab 32

The Administration Tab 37

The Status Tab 43

Appendix A: Troubleshooting 47

Common Problems and Solutions 47

Frequently Asked Questions 55

Appendix B: Wireless Security 62

Security Precautions 62

Security Threats Facing Wireless Networks 62

Wireless-G ADSL Home Gateway

Appendix C: Finding the MAC Address and IP Address for Your

Ethernet Adapter 65

Windows 98 or Me Instructions 65

Windows 2000 or XP Instructions 66

Appendix D: Upgrading Firmware 67

Appendix E: Glossary 68

Appendix F: Regulatory Information 75

Appendix G: Warranty Information 80

Appendix H: Specifications 81

Appendix I: Contact Information 83

Wireless-G ADSL Home Gateway

List of Figures

Figure 2-1: Network 4

Figure 3-1: Ports and Reset Button on Side Panel 6

Figure 3-2: LEDs on Side Panel 7

Figure 3-3: Top Panel 8

Figure 3-4: Top Panel with Optional Antenna 8

Figure 3-5: Bottom Panel with Stand in Closed Position 9

Figure 3-6: Gateway Using Stand 9

Figure 4-1: Connect the ADSL Line 11

Figure 4-2: Connect a PC 11

Figure 4-3: Connect the Power 11

Figure 4-4: Connect the ADSL Line 12

Figure 4-5: Connect the Power 12

Figure 5-1: Login Screen 15

Figure 5-2: Basic Setup 15

Figure 5-3: RFC 1483 Bridged - Dynamic IP 16

Figure 5-4: RFC 1483 Bridged - Static IP 16

Figure 5-5: RFC 1483 Routed 17

Figure 5-6: RFC 2516 PPPoE 17

Figure 5-7: RFC 2364 PPPoA 18

Figure 5-8: Bridged Mode Only 18

Figure 5-9: Optional Settings 19

Figure 5-10: DynDNS.org 20

Figure 5-11: TZO.com 20

Figure 5-12: Advanced Routing 21

Figure 5-13: Routing Table 22

Figure 5-14: Basic Wireless Settings 23

Figure 5-15: WPA Pre-Shared Key 24

Figure 5-16: WEP 25

Figure 5-17: Wireless Network Access 26

Figure 5-18: MAC Address Filter List 26

Figure 5-19: Wireless Client MAC List 26

Figure 5-20: Advanced Wireless Settings 27

Wireless-G ADSL Home Gateway

Figure 5-21: Security 28

Figure 5-22: Firewall Log 29

Figure 5-23: Internet Access 30

Figure 5-24: Internet Policy Summary 30

Figure 5-25: List of PCs 31

Figure 5-26: Add/Edit Service 31

Figure 5-27: Single Port Forwarding 32

Figure 5-28: Port Range Forwarding 33

Figure 5-29: Port Triggering 34

Figure 5-30: DMZ 35

Figure 5-31: QoS 36

Figure 5-32: Management 37

Figure 5-33: Allowed IP - IP Range 37

Figure 5-34: Reporting 39

Figure 5-35: System Log 39

Figure 5-36: Ping Test 40

Figure 5-37: Backup&Restore 40

Figure 5-38: Factory Defaults 41

Figure 5-39: Firmware Upgrade 41

Figure 5-40: Reboot 42

Figure 5-41: Gateway 43

Figure 5-42: Local Network 44

Figure 5-43: DHCP Active IP Table 44

Figure 5-44: ARP/RARP Table 44

Figure 5-45: Wireless 45

Figure 5-46: Networked Computers 45

Figure 5-47: DSL Connection 46

Figure C-1: IP Configuration Screen 65

Figure C-2: MAC Address/Adapter Address 65

Figure C-3: MAC Address/Physical Address 66

Figure D-1: Firmware Upgrade 67

1

Chapter 1: Introduction

Welcome

Wireless-G ADSL Home Gateway

Chapter 1: Introduction

Welcome

Thank you for choosing the Wireless-G ADSL Home Gateway. This Gateway will provide your computers with a

high-speed Internet connection as well as resources, including files and printers. Since the Gateway is wireless,

Internet access can be shared over the wired network as well as the wireless broadcast at up to 11Mbps for

Wireless-B or up to 54Mbps for Wireless-G.

How does the Gateway do all of this? By connecting the Internet, as well as your computers and peripherals, to

the Gateway, then the Gateway can direct and control communications for your network.

To protect your data and privacy, the Gateway features an advanced firewall to keep out Internet intruders.

Wireless transmissions can be protected by powerful data encryption. In addition, you can safeguard your family

with parental control features such as Internet access restrictions and keyword blocking. You can configure the

Gateway’s settings through the easy-to-use, browser-based utility.

But what does all of this mean?

Networks are useful tools for sharing Internet access and computer resources. You can access one printer from

different computers and access data located on another computer’s hard drive. Networks are even used for

playing multiplayer video games. So, networks not only are useful in homes and offices, but also can be fun.

PCs on a wired network create a LAN, or Local Area Network. They are connected with Ethernet cables, which is

why the network is called “wired”. PCs equipped with wireless cards or adapters can communicate without

cumbersome cables. By sharing the same wireless settings, within their transmission radius, they form a

wireless network. This is sometimes called a WLAN, or Wireless Local Area Network. Since the Gateway has

wireless capabilities, it can bridge your wired and wireless networks, letting them communicate with each other.

With your networks all connected, wired, wireless, and the Internet, you can now share files and Internet

access—and even play games. All the while, the Wireless-G ADSL Home Gateway protects your networks from

unauthorized and unwelcome users.

Linksys recommends using the Setup CD-ROM for first-time installation of the Gateway. If you do not wish to run

the Setup Wizard on the Setup CD-ROM, then use the instructions in this Guide to help you connect the Gateway,

set it up, and configure it to bridge your different networks. These instructions should be all you need to get the

most out of the Wireless-G ADSL Home Gateway.

lan (local area network): The computers and

networking products that make up the network in

your home or office.

nat (network address translation): NAT technology

translates IP addresses of a local area network to a

different IP address for the Internet.

wpa (wi-fi protected access): a wireless security

protocol using TKIP (Temporal Key Integrity Protocol)

encryption, which can be used in conjunction with a

RADIUS server.

spi (stateful packet inspection) firewall: a technology

that inspects incoming packets of information before

allowing them to enter the network.

firewall: Security measures that protect the

resources of a local network from intruders.

network: a series of computers or devices

connected for the purpose of data sharing,

storage, and/or transmission between users

2

Chapter 1: Introduction

What’s in this User Guide?

Wireless-G ADSL Home Gateway

What’s in this User Guide?

This user guide covers the steps for setting up and using the Wireless-G ADSL Home Gateway.

• Chapter 1: Introduction

This chapter describes applications of the Wireless-G ADSL Home Gateway and this User Guide.

• Chapter 2: Planning Your Network

This chapter describes the basics of networking.

• Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway

This chapter describes the physical features of the Gateway.

• Chapter 4: Connecting the Wireless-G ADSL Home Gateway

This chapter instructs you on how to connect the Gateway to your network.

• Chapter 5: Configuring the Wireless-G ADSL Home Gateway

This chapter explains how to use the Web-based Utility to configure the settings on the Gateway.

• Appendix A: Troubleshooting

This appendix describes some problems and solutions, as well as frequently asked questions, regarding

installation and use of the Wireless-G ADSL Home Gateway.

• Appendix B: Wireless Security

This appendix explains the risks of wireless networking and some solutions to reduce the risks.

• Appendix C: Finding the MAC Address and IP Address for your Ethernet Adapter.

This appendix describes how to find the MAC address for your computer’s Ethernet adapter so you can use

the MAC filtering and/or MAC address cloning feature of the Gateway.

• Appendix D: Upgrading Firmware

This appendix instructs you on how to upgrade the firmware on the Gateway if you should need to do so.

• Appendix E: Glossary

This appendix gives a brief glossary of terms frequently used in networking.

• Appendix F: Specifications

This appendix provides the technical specifications for the Gateway.

• Appendix G: Warranty Information

This appendix supplies the warranty information for the Gateway.

3

Chapter 1: Introduction

What’s in this User Guide?

Wireless-G ADSL Home Gateway

• Appendix H: Regulatory Information

This appendix supplies the regulatory information regarding the Gateway.

• Appendix I: Contact Information

This appendix provides contact information for a variety of Linksys resources, including Technical Support.

4

Chapter 2: Planning Your Network

The Gateway’s Functions

Wireless-G ADSL Home Gateway

Chapter 2: Planning Your Network

The Gateway’s Functions

A Gateway is a network device that connects two networks together.

In this instance, the Gateway connects your Local Area Network (LAN), or the group of computers in your home or

office, to the Internet. The Gateway processes and regulates the data that travels between these two networks.

The Gateway’s NAT feature protects your network of computers so users on the public, Internet side cannot “see”

your computers. This is how your network remains private. The Gateway protects your network by inspecting

every packet coming in through the Internet port before delivery to the appropriate computer on your network.

The Gateway inspects Internet port services like the web server, ftp server, or other Internet applications, and, if

allowed, it will forward the packet to the appropriate computer on the LAN side.

Remember that the Gateway’s ports connect to two sides. The LAN ports connect to the LAN, and the ADSL port

connects to the Internet. The LAN ports transmit data at 10/100Mbps.

IP Addresses

What’s an IP Address?

IP stands for Internet Protocol. Every device on an IP-based network, including computers, print servers, and

Gateways, requires an IP address to identify its “location,” or address, on the network. This applies to both the

Internet and LAN connections. There are two ways of assigning an IP address to your network devices. You can

assign static IP addresses or use the Gateway to assign IP addresses dynamically.

Static IP Addresses

A static IP address is a fixed IP address that you assign manually to a computer or other device on the network.

Since a static IP address remains valid until you disable it, static IP addressing ensures that the device assigned

it will always have that same IP address until you change it. Static IP addresses must be unique and are

commonly used with network devices such as server computers or print servers.

NOTE: Since the Gateway is a device that connects

two networks, it needs two IP addresses—one for

the LAN, and one for the Internet. In this User Guide,

you’ll see references to the “Internet IP address”

and the “LAN IP address.”

Since the Gateway uses NAT technology, the only IP

address that can be seen from the Internet for your

network is the Gateway’s Internet IP address.

However, even this Internet IP address can be

blocked, so that the Gateway and network seem

invisible to the Internet—see the Block WAN

Requests description under Security in “Chapter 5:

Configuring the Wireless-G ADSL Home Gateway.”

Figure 2-1: Network

ip (internet protocol): a protocol used to send data

over a network

5

Chapter 2: Planning Your Network

IP Addresses

Wireless-G ADSL Home Gateway

Since you use the Gateway to share your DSL Internet connection, contact your ISP to find out if they have

assigned a static IP address to your account. If so, you will need that static IP address when configuring the

Gateway. You can get that information from your ISP.

Dynamic IP Addresses

A dynamic IP address is automatically assigned to a device on the network, such as computers and print servers.

These IP addresses are called “dynamic” because they are only temporarily assigned to the computer or device.

After a certain time period, they expire and may change. If a computer logs onto the network (or the Internet) and

its dynamic IP address has expired, the DHCP server will automatically assign it a new dynamic IP address.

DHCP (Dynamic Host Configuration Protocol) Servers

Computers and other network devices using dynamic IP addressing are assigned a new IP address by a DHCP

server. The computer or network device obtaining an IP address is called the DHCP client. DHCP frees you from

having to assign IP addresses manually every time a new user is added to your network.

A DHCP server can either be a designated computer on the network or another network device, such as the

Gateway. By default, the Gateway’s DHCP Server function is enabled.

If you already have a DHCP server running on your network, you must disable one of the two DHCP servers. If you

run more than one DHCP server on your network, you will experience network errors, such as conflicting IP

addresses. To disable DHCP on the Gateway, see the DHCP section in “Chapter 5: Configuring the Wireless-G

ADSL Home Gateway.”

6

Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway

Ports and Reset Button on Side Panel

Wireless-G ADSL Home Gateway

Chapter 3: Getting to Know the Wireless-G ADSL Home

Gateway

Ports and Reset Button on Side Panel

The Gateway’s ports and Reset button are located on a side panel.

Line The Line port connects to the ADSL line.

Ethernet (1-4) The Ethernet ports connect to your computers and other network devices.

Reset Button There are two ways to reset the Gateway's factory defaults. Either press the Reset Button, for

approximately ten seconds, or restore the defaults from the Factory Defaults screen of the

Administration tab in the Gateway’s Web-based Utility.

Power The Power port is where you will connect the power adapter.

IMPORTANT: Resetting the Gateway to factory

defaults will erase all of your settings

(including Internet connection, wireless, and

other settings) and replace them with the

factory defaults. Do not reset the Gateway if

you want to retain these settings.

Figure 3-1: Ports and Reset Button on Side Panel

7

Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway

LEDs on Side Panel

Wireless-G ADSL Home Gateway

LEDs on Side Panel

The Gateway's LEDs, which indicate network activity, are located on the other side panel.

POWER Green. The POWER LED lights up when the Gateway is powered on.

WIRELESS Green. The WIRELESS LED lights up whenever there is a successful wireless connection. If the

LED is flashing, the Gateway is actively sending or receiving data to or from one of the devices

on the network.

ETHERNET (1-4) Green. The ETHERNET LED serves two purposes. If the LED is continuously lit, the Gateway is

successfully connected to a device through the LAN port. If the LED is flashing, it is an

indication of any network activity.

DSL Green. The DSL LED lights up whenever there is a successful DSL connection. The LED blinks

while the Gateway is establishing the ADSL connection.

INTERNET Green. The INTERNET LED lights up green when an Internet connection to the Internet Service

Provider (ISP) is established. The INTERNET LED lights up red when the connection to the ISP

fails.

Figure 3-2: LEDs on Side Panel

8

Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway

The Top Panel

Wireless-G ADSL Home Gateway

The Top Panel

The Gateway comes with a built-in antenna; however, you can attach an optional antenna. (Note: This antenna is

currently not available in Europe.) The Linksys 5dBi High Gain Antenna for SMA Connectors (model number:

HGA5S) is available for increased range. The Gateway’s SMA port for the optional antenna is located on the top

panel. To access the SMA port, push the tab. To attach the antenna, insert the base of the antenna into the SMA

port and tighten it clockwise by hand.

Figure 3-3: Top Panel

Figure 3-4: Top Panel with Optional

Antenna

Tab

Antenna Base

SMA Port

Optional Linksys 5dBi Antenna (model number: HGA5S)

Note: This antenna is currently not available in Europe, and Linksys does not support or

recommend use of an external antenna with this product in Europe.

9

Chapter 3: Getting to Know the Wireless-G ADSL Home Gateway

The Bottom Panel

Wireless-G ADSL Home Gateway

The Bottom Panel

The Gateway has a built-in stand available. If you place the Gateway flat on a surface, then you can leave the

stand in the closed position. However, if you want the Gateway to be upright, swivel the stand clockwise 90º and

position the Gateway accordingly.

Figure 3-5: Bottom Panel with Stand in

Closed Position

Figure 3-6: Gateway Using Stand

10

Chapter 4: Connecting the Wireless-G ADSL Home Gateway

Overview

Wireless-G ADSL Home Gateway

Chapter 4: Connecting the Wireless-G ADSL Home Gateway

Overview

The installation technician from your ISP should have left the setup information for the modem with you after

installing your broadband connection. If not, you can call your ISP to request that data.

After you have the setup information you need for your specific type of Internet connection, you can begin

installation and setup of the Gateway.

If you want to use a computer with an Ethernet adapter to configure the Gateway, continue to “Wired Connection

to a Computer.” If you want to use a computer with a wireless adapter to configure the Gateway, continue to

“Wireless Connection to a Computer.”

11

Chapter 4: Connecting the Wireless-G ADSL Home Gateway

Wired Connection to a Computer

Wireless-G ADSL Home Gateway

Wired Connection to a Computer

1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.

2. Connect a phone cable from the Line port on the Gateway’s side panel to the wall jack of the ADSL line. A

small device called a microfilter (not included) may be necessary between each phone and wall jack to

prevent interference. Contact your ISP if you have any questions.

3. Connect one end of an Ethernet network cable to one of the Ethernet ports (labeled 1-4) on the back of the

Gateway, and the other end to an Ethernet port on a computer.

Repeat this step to connect more computers, a switch, or other network devices to the Gateway.

4. Connect the power adapter to the Gateway’s Power port, and then plug the power adapter into a power outlet.

The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The

Power LED will flash for a few seconds, and then it will be solidly lit when the self-test is complete. If the LED

flashes for one minute or longer, see “Appendix A: Troubleshooting.”

5. Power on one of your computers that is connected to the Gateway.

Go to “Chapter 5: Configuring the Wireless-G ADSL Home Gateway.”

Figure 4-2: Connect a PC

Figure 4-1: Connect the ADSL Line

Figure 4-3: Connect the Power

NOTE: You should always plug the Gateway’s power adapter into a power strip with

surge protection.

IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure to only place

the microfilters between the phone and the wall jack and not between the Gateway and the wall

jack or your ADSL will not connect.

For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden,

Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used between

the Gateway and the wall jack, because the microfilter will have the RJ-11 connector.

Annex B users (E1 and DE versions of the Gateway) must use the included special cable to connect

the Gateway to the wall jack (RJ-45 to RJ-12). If you require splitters or special jacks, please

contact your service provider.

NOTE:

A small device called a microfilter (not included) may be necessary between each phone

and wall jack to prevent interference. Contact your ISP if you have any questions.

12

Chapter 4: Connecting the Wireless-G ADSL Home Gateway

Wireless Connection to a Computer

Wireless-G ADSL Home Gateway

Wireless Connection to a Computer

If you want to use a wireless connection to access the Gateway, follow these instructions:

1. Make sure that all of your network’s hardware is powered off, including the Gateway and all computers.

2. Connect a phone cable from the Line port on the Gateway’s back panel to the wall jack of the ADSL line. A

small device called a microfilter (not included) may be necessary between each phone and wall jack to

prevent interference. Contact your ISP if you have any questions.

3. Connect the power adapter to the Power port, and then plug the power adapter into a power outlet.

The Power LED on the front panel will light up green as soon as the power adapter is connected properly. The

Power LED will flash for a few seconds, and then it will be solidly lit when the self-test is complete. If the LED

flashes for one minute or longer, see “Appendix A: Troubleshooting.”

4. Power on one of the computers on your wireless network(s).

5. For initial access to the Gateway through a wireless connection, make sure the computer’s wireless adapter

has its SSID set to linksys (the Gateway’s default setting), and its wireless security is disabled. After you have

accessed the Gateway, you can change the Gateway and this computer’s adapter settings to match your usual

network settings.

Go to “Chapter 5: Configuring the Wireless-G ADSL Home Gateway.”

NOTE: You should always change the SSID from its

default, linksys, and enable wireless security.

NOTE:

A small device called a microfilter (not included) may be necessary between each phone

and wall jack to prevent interference. Contact your ISP if you have any questions.

IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure you only place

the microfilters between the phone and the wall jack and not between the Gateway and the wall jack

or your ADSL will not connect.

For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden, Switzerland,

United Kingdom, etc.), except for ISDN users, the microfilter has to be used between the Gateway and

the wall jack, because the microfilter will have the RJ-11 connector.

Annex B users (E1 and DE versions of the Gateway) must use the included special cable to connect

the Gateway to the wall jack (RJ-45 to RJ-12). If you require splitters or special jacks, please contact

your service provider.

Figure 4-4: Connect the ADSL Line

Figure 4-5: Connect the Power

13

Chapter 5: Configuring the Wireless-G ADSL Home Gateway

Overview

Wireless-G ADSL Home Gateway

Chapter 5: Configuring the Wireless-G ADSL Home Gateway

Overview

Follow the steps in this chapter and use the Gateway’s web-based utility to configure the Gateway. This chapter

will describe each web page in the Utility and each page’s key functions. The utility can be accessed via your web

browser through use of a computer connected to the Gateway. For a basic network setup, most users only have to

use the following screens of the Utility:

• Basic Setup. On the Basic Setup screen, enter the settings provided by your ISP.

• Management. Click the Administration tab and then the Management tab. The Gateway’s default username

and password is admin. To secure the Gateway, change the Password from its default.

There are seven main tabs: Setup, Wireless, Security, Access Restrictions, Applications & Gaming, Administration,

and Status. Additional tabs will be available after you click one of the main tabs.

Setup

• Basic Setup. Enter the Internet connection and network settings on this screen.

• DDNS. To enable the Gateway’s Dynamic Domain Name System (DDNS) feature, complete the fields on this

screen.

• Advanced Routing. On this screen, you can alter NAT and routing configurations.

Wireless

• Basic Wireless Settings. You can choose your wireless network settings on this screen.

• Wireless Security. Configure your wireless security settings on this screen.

• Wireless Access. This screen lets you control access to your wireless network.

• Advanced Wireless Settings. On this screen you can access the advanced wireless network settings.

NOTE: For added security, you should change

the password through the Administration tab.

HAVE YOU: Enabled TCP/IP on your

computers? Computers communicate over the

network with this protocol. Refer to Windows

Help for more information on TCP/IP.

14

Chapter 5: Configuring the Wireless-G ADSL Home Gateway

Overview

Wireless-G ADSL Home Gateway

Security

On this screen you can disable or enable the firewall, set up filters, block WAN requests, and enable or disable

Virtual Private Networks (VPN) PassThrough.

Access Restrictions

• Internet Access. This screen allows you to control the Internet usage and traffic on your local network.

Applications & Gaming

• Single Port Forwarding. Use this screen to set up common services or applications that require forwarding on

a single port.

• Port Range Forwarding. To set up public services or other specialized Internet applications that require

forwarding on a range of ports, use this screen.

• Port Triggering. To set up triggered ranges and forwarded ranges for Internet applications, click this tab.

• DMZ. To allow one local computer to be exposed to the Internet for use of special-purpose services, use this

screen.

• QoS. Use Quality of Service (QoS) to assign different priority levels to different types of data transmissions.

Administration

• Management. On this screen, alter Gateway access, Simple Network Management Protocol (SNMP), Universal

Plug and Play (UPnP), IGMP-Proxy (IGMP stands for Internet Group Multicast Protocol), and wireless

management settings.

• Reporting. If you want to view or save activity logs, click this tab.

• Diagnostics. Use this screen to run a Ping test.

• Backup&Restore. On this screen, you can back up or restore the Gateway’s configuration.

• Factory Defaults. If you want to restore the Gateway’s factory default settings, use this screen.

• Firmware Upgrade. Click this tab if you want to upgrade the Gateway’s firmware.

• Reboot. If you need to do a hard or soft reboot of the Gateway, use this screen.

vpn (virtual private network): a security

measure to protect data as it leaves one

network and goes to another over the Internet.

La pagina sta caricando ...

Linksys WAG200G Manuale utente

Questo manuale è adatto anche per

Linksys WAG200G Manuale utente

in altre lingue

Documenti correlati

Altri documenti