Gigabyte GA-8VT880-L Manuale utente

When you installing AGP card, please make sure the following

notice is fully understood and practiced. If your AGP card has

"AGP 4X/8X(1.5V) notch"(show below), please make sure your AGP

card is AGP 4X/8X (1.5V).

Caution: AGP 2X(3.3V) card is not supported by VIA PT880. You might

experiencesystem unable to boot up normally. Please insert an AGP

4X/8X (1.5V) card

Example 1: Diamond Vipper V770 golden finger is compatible with

2X/4X mode AGP slot. It can be switched between AGP 2X(3.3V) or 4X

(1.5V) mode by adjusting the jumper. The factory default for this card is

2X(3.3V).

The GA-8VT880 Series motherboards might not function properly, if you

install this card without switching the jumper to 4X(1.5V) mode in it.

Example 2: Some ATi Rage 128 Pro graphics cards made by

"Power Color", the graphics card manufacturer & some SiS 305 cards,

their golden finger is compatible with 2X/4X mode AGP slot, but they

support 2X(3.3V) only. The GA-8VT880 Series motherboards might not

function properly, If you install this card in it.

Note : Although Gigabyte's AG32S(G) graphics card is based on

ATi Rage 128 Pro chip, the design of AG32S(G) is compliance

with AGP 4X(1.5V) specification. Therefore, AG32S (G)will work

fine with VIA PT880 based motherboards.

AGP 4X/8X notch

M The author assumes no responsibility for any errors or omissions

that may appear in this document nor does the author make a

commitment to update the information contained herein.

M Third-party brands and names are the property of theirrespective

owners.

M Please do not remove any labels on motherboard, thismay void the

warranty of this motherboard.

M Due to rapid change in technology, some of the specifications might

be out of date before publication of this booklet.

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8VT880 / GA-8VT880-L / GA-8VT880 Ultra

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive

o EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment

o EN 61000-3-2*

T EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”

o EN 55013

Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment

o EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”

o EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

T EN 50081-1

Generic emission standard Part 1:

Residual commercial and light industry

T EN 50082-1

Generic immunity standard Part 1:

Residual commercial and light industry

o EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment

o EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment

o EN 55082-2

T EN 55022

Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus

o ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)

o EN50091-2

o EN 55020

o DIN VDE 0855

o part 10

o part 12

(EC conformity marking)

T CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use

o EN 60950

o EN 60065

Safety of household and similar

electrical appliances

o EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp)

Date : November 25, 2003

T EN 60555-3

Timmy Huang

o EN 50091-1

Timmy Huang

Safety for information technology equipment

including electrical bussiness equipment

General and Safety requirments for

uninterruptible power systems (UPS)

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109

(a),Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible PartName:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature:

Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8VT880 / GA-8VT880-L / GA-8VT880 Ultra

Date:

ERIC LU

November 25,2003

USER'S MANUAL

GA-8VT880 Series

P4 Titan Series Motherboard

Pentium

®

4 Processor Motherboard

Rev. 1001

12ME-8VT880U-1001

- 2 -GA-8VT880 Series Motherboard

English

Table of Content

WARNING! ..............................................................................................4

Chapter 1 Introduction.............................................................................5

Features Summary....................................................................................... 5

GA-8VT880 Series Motherboard Layout...................................................... 8

Block Diagramt...................................................................................9

Chapter 2 Hardware Installation Process..............................................11

Step 1: Install the Central Processing Unit (CPU)...................................... 12

Step 1-1 : CPU Installation .............................................................................. 12

Step 1-2 : CPU Heat Sink Installation.............................................................. 13

Step 2: Install memory modules................................................................. 14

Step 3: Install expansion cards .................................................................. 17

Step 4: Connect ribbon cables, cabinet wires, and power supply.............. 18

Step 4-1 : I/O Back Panel Introduction ............................................................ 18

Step 4-2 : Connectors & Jumper Setting Introduction...................................... 20

Chapter 3 BIOS Setup ..........................................................................35

The Main Menu (For example: BIOS Ver. :F1)........................................... 36

Standard CMOS Features.......................................................................... 38

Advanced BIOS Features........................................................................... 41

Integrated Peripherals ................................................................................ 43

Table of Content

English

- 3 -

Power Management Setup......................................................................... 48

PnP/PCI Configurations ............................................................................. 50

PC Health Status........................................................................................ 51

Frequency/Voltage Control......................................................................... 53

Load Fail-Safe Defaults.............................................................................. 56

Load Optimized Defaults ............................................................................ 57

Set Supervisor/User Password .................................................................. 58

Save & Exit Setup ...................................................................................... 59

Exit Without Saving ................................................................................... 60

Chapter 4 Technical Reference.............................................................63

Flash BIOS Method Introduction ................................................................ 63

@ BIOS Introduction .................................................................................. 78

Easy Tune 4

TM

Introduction......................................................................... 79

2-/4-/6-Channel Audio Function Introduction.............................................. 80

Jack-Sensing Introduction.......................................................................... 86

UAJ Introduction......................................................................................... 88

Xpress Recovery Introduction .................................................................... 90

SATA ATA BIOS Setting Utility Introduction ................................................ 93

Chapter 5 Appendix.............................................................................101

- 4 -GA-8VT880 Series Motherboard

English

WARNING!

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

other components.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don't line up with the holes on the base and there

are no slots to attach the spacers, do not become alarmed you can still attach the spacers to the

mounting holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so

be careful of your hands). In this way you can still attach the motherboard to the base without worrying

about short circuits. Sometimes you may need to use the plastic springs to isolate the screw from the

motherboard PCB surface, because the circuit wire may be near by the hole. Be careful, don't let the

screw contact any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may

damage the board or cause board malfunctioning.

Installing the motherboard to the chassis…

Introduction- 5 -

English

Form Factor  30.5cm x 24.4cm ATX size form factor, 4 layers PCB.

Motherboard  GA-8VT880 Series:

GA-8VT880 Ultra / GA-8VT800-L / GA-8VT880

CPU  Socket 478 for Intel® Micro FC-PGA2 Pentium® 4 processor

 Support Intel® Pentium® 4 (Northwood, Prescott) processor

 Support Intel® Pentium® 4 Processor with HT Technology

 Intel Pentium®4 800/533/400 MHz FSB

 2nd cache depends on CPU

Chipset  Chipset VIA PT880 HOST/AGP/Controller

 VT8237 I/O Controller Hub

Memory  4 184-pin DDR DIMM sockets

 Supports Dual Channel DDR400/DDR333/DDR266 DIMM

 Supports 128MB/256MB/512MB/1GB unbuffered DRAM

 Supports up to 4GB DRAM (Max)

I/O Control  IT8705

Slots  1 AGP 3.0 slot supports 8X/4X mode

 5 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE  2 IDE controllers on the VIA VT8237 PCI chipset

provides IDE HDD/CD-ROM (IDE1, IDE2) with PIO, Bus Master

(Ultra DMA33/ATA66/ATA100/ATA133) operation modes.

 IDE3 and IDE4 Compatible with RAID,Ultra ATA133/100.t

On-Board Peripherals  1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

 1 Parallel port supports Normal/EPP/ECP mode

 2 Serial ports (COMA and COMB)

 8 USB 2.0/1.1 ports (4 x Rear, 4 xFront by cable)

 3 IEEE1394 ports (by cable)

 1 IrDA connector for IR

 1 Front Audio Connector

Chapter 1 Introduction

Features Summary

to be continued......

t For GA-8VT880 Ultra * For GA-8VT880-L

- 6 -GA-8VT880 Series Motherboard

English

Hardware Monitor y CPU/System fan revolution detect

y CPU temperature detect

y CPU warning temperature

y System voltage detect

y CPU/System fan fail warning

y CPU Smart Fan control()

On-Board LAN(*,



) y Builit in Realtek 8110S Gigabit ()

y Builit in Realtek 8100C (*)

y 1 RJ45 port(*,



)

On-Board Sound y Realtek ALC658 CODEC (UAJ)

y Supports Jack Sensing function

y Line Out / 2 front speaker

y Line In / 2 rear speaker(by s/w switch)

y Mic In / center& subwoofer(by s/w switch)

y SPDIF Out /SPDIF In

y CD_In/ AUX_IN/ Game Connector

On-Board SATA RAID y Built in VT8237

y Supports Disk striping (RAID0) or DISK Mirroring (RAID1)

y Supports UDMA up to 150 MB/sec

y Up to 2 SATA Devices

(Note)

On-Board IDE RAID () y Onboard GigaRAID IT8212F chipset

y Supports data striping (RAID 0) or mirroring (RAID 1) or

striping+mirroring (RAID 0 + RAID 1)

y Supports JBOD function

y Supports concurrent dual ATA133 IDE controller operation

y Support ATAPI mode for HDD

y Supports IDE bus master operation

y Support ATA133/RAID mode switch by BIOS

y Displays status and error checking messages during boot-up

y Mirroring supports automatic background rebuilds

y Features LBA and Extended Interrupt 13 drive translation in

controller onboard BIOS

to be continued......

(Note) It is recommended to use SATA (1.5Gb/s) hard disks.



 For GA-8VT880 Ultra * For GA-8VT880-L

Introduction- 7 -

English

On-Board IEEE1394  Built-in VT6306

PS/2 Connector  PS/2 Keyboard interface and PS/2 Mouse interface

BIOS  Licensed AWARD BIOS

 Supports Dual BIOS (t)

 Supports Face Wizard

 Supports Q-Flash

Additional Features  PS/2 Keyboard power on by password

 PS/2 Mouse power on

 STR(Suspend-To-RAM)

 AC Recovery

 Poly fuse for keyboard over-current protection

 USB KB/Mouse wake up from S3

 Supports EasyTune 4

 Supports @BIOS

Overclocking  Over Voltage (DDR/AGP/CPU) by BIOS

 Over Clock (DDR/AGP/CPU/PCI) by BIOS

Please set the CPU host frequency in accordance with your processor's specifications.

We don't recommend you to set the system bus frequency over the CPU's specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets, SDRAM, Cards….etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires

all of the following platform components:

- CPU: An Intel

®

Pentium 4 Processor with HT Technology

- Chipset: An Intel

®

Chipset that supports HT Technology

- BIOS: A BIOS that supports HT Technology and has it enabled

- OS: An operation system that has optimizations for HT Technology

t For GA-8VT880 Ultra * For GA-8VT880-L

- 8 -GA-8VT880 Series Motherboard

English

GA-8VT880 Series Motherboard Layout

GA-8VT880 Ultra

KB_MS

COMA

ATX_12V

SOCKET478

CPU_FAN

ATX

FDD

IDE1

IDE3t

LPT

DDR2

USB

Hyper Threading

SPDIF_IO

F_PANEL

PCI5

MAIN

BIOS

F_USB2F_USB1

GAME

F_AUDIO

PWR_LED

CODEC

ITE8705F

BATTERY

VT8237

PCI2

PCI3

PCI4

AUX_IN

CLR_CMOS

SUR_CEN

PCI1

DDR3

DDR1

CD_IN

SYS_FAN

AGP

VIA PT880

COMB

RTL8110S t

DDR4

USB

/LAN

AUDIO

NB_FANt

IDE2

SATA1

SATA0

IDE4t

GigaRAID

IT8212 t

VIA VT6306

Backup

BIOS t

F1_1394

F2_1394

INFO_LINK

RTL8110C *

PWR_FANt

t

For GA-8VT880 Ultra * For GA-8VT880-L

IR

Introduction- 9 -

English

Block Diagram

"t" FOR GA-8VT880 Ultra Only. "* " FOR GA-8VT880-L Only.

RJ45(*,t)

RTL8110St

RTL8100C*

2 Serial

ATA

Pentium 4

Socket 478

CPU

VIA PT880

VT8237

CPUCLK+/- (100/133/200MHz)

System Bus

400/533/800MHz

266/333/400MHz

GCLKNB

HCLK+/- (100/133/200MHz)

66MHz

33 MHz

14.318 MHz

48 MHz

33 MHz

LPC BUS

AGP 8X/4X

AGPCLK

(66MHz)

5 PCI

PCICLK

(33MHz)

8 USB

(2.0/1.1)

Ports

ATA33/66/

100/133

IDE Channels

Floppy

LPT Port

PS/2 KB/Mouse

COM

Ports

CLK GEN

GCLKNB

CPUCLK+/- (100/133/200MHz)

AGPCLK (66MHz)

HCLK+/- (100/133/200MHz)

PCICLK (33MHz)

USBCLK (48MHz)

14.318 MHz

33 MHz

ITE8705

Game Port

BIOS/

Dual BIOSt

48 MHz

VCLK (66MHz)

DDR

AC97 Link

MIC

LINE-IN

LINE-OUT

AC97

CODEC

IDE3t

IEEE1394

VT6306

IDE4t

GigaRAID

IT8212t

48 MHz

3 IEEE1394

- 10 -GA-8VT880 Series Motherboard

English

- 11 - Hardware Installation Process

English

To set up your computer, you must complete the following steps:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Connect ribbon cables, cabinet wires, and power supply

Chapter 2 Hardware Installation Process

Congratulations you have accomplished the hardware installation!

Turn on the power supply or connect the power cable to the power outlet. Continue with

the BIOS/software installation.

Step 2

Step 4

Step 1

Step 4

Step 3

- 12 -GA-8VT880 Series Motherboard

English

Step 1: Install the Central Processing Unit (CPU)

Step 1-1: CPU Installation

Pin1 indicator

3. CPU Top View

2. Pull the rod to the 90-degree directly.

4. Locate Pin 1 in the socket and look

for a (golden) cut edge on the CPU

upper corner. Then insert the CPU

into the socket.

Angling the

rod to 65

0

Socket

Actuation

Lever

Pin1 indicator

1. Angling the rod to 65-degree maybe feel a

kind of tight, and then continue pull the rod

to 90-degree when a noise "cough" made.

Before installing the processor , adhere to the following warning:

If you do not match the CPU socket Pin 1 and CPU cut edge well, it will

cause improper installation. Please change the insert orientation.

Please make sure the CPU type is supported by the motherboard.

- 13 - Hardware Installation Process

English

Step 1-2 : CPU Cooling Fan Installation

1. Please use Intel approved cooling fan.

2. We recommend you to apply the thermal tape to provide better heat conduction

between your CPU and cooling fan.

(The CPU cooling fan might stick to the CPU due to the hardening of the thermal

paste. During this condition if you try to remove the cooling fan, you might pull the

processor out of the CPU socket alone with the cooling fan, and might damage the

processor. To avoid this from happening, we suggest you to either use thermal

tape instead of thermal paste, or remove the cooling fan with extreme caution.)

3. Make sure the CPU fan power cable is plugged in to the CPU fan connector, this

completes the installation.

Please refer to CPU cooling fan user's manual for more detail installation procedure.

2. Make sure the CPU fan is plugged to

the CPU fan connector, than install

complete.

1. Fasten the cooling fan supporting-base

onto the CPU socket on the

mainboard.

Before installing the CPU Cooling Fan , adhere to the following warning:

- 14 -GA-8VT880 Series Motherboard

English

The motherboard has 4 dual inline memory module (DIMM) sockets. The BIOS will automatically

detects memory type and size. To install the memory module, just push it vertically into the DIMM

socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary

between sockets.

Step 2: Install memory modules

DDR

Notch

Before installing the processor and heatsink, adhere to the following warning:

1.When RAM_LED is ON, do not install/remove DIMM from socket.

2.Please note that the DIMM module can only fit in one direction due to the one notches.

Wrong orientation will cause improper installation. Please change the insert orientation.

1. The DIMM slot has a notch, so the DIMM

memory module can only fit in one direction.

2. Insert the DIMM memory module vertically into

the DIMM slot. Then push it down.

3. Close the plastic clip at both edges of the DIMM

slots to lock the DIMM module.

Reverse the installation steps when you wish

to remove the DIMM module.

- 15 - Hardware Installation Process

English

Below are the explanations:

1. One, or three memory modules are installed: The Dual Channel Technology will not operate

when one, three, memory modules are installed and they will only work as Single Channel.

2. Two DDR memory modules are installed (the same memory size and type): The Dual Chan-

nel Technology will operate when two DDR memory modules are inserted individually into

Channel A and Channel B (DIMM 1 pairs up with DIMM 3, DIMM 2 and DIMM 4). However,

if the two DDR memory modules are inserted into the same Channel (DIMM 1,2 or DIMM 3,

4) then Dual Channel Technology will not operate.

3. Three memory modules are installed: Please note that The Dual Channel Technology will

not operate when three DDR memory modules are installed; part of them will not be detected.

4. If four DDR memory modules are installed (two pairs of DDR memory modules with the

same memory size and type): The Dual Channel Technology will operate when a pair of

DDR memory modules are inserted into DIMM1, 3 and another pair into DIMM 2,4.

Dual Channel DDR:

GA-8VT880 Series supports Dual Channel Technology.

When Dual Channel Technology is activated, the bandwidth of memory bus will be double the original one,

with the fastest speed at 6.4GB/s DDR400.

GA-8VT880 Series includes four DIMM slots, and each Channel has 2 DIMMs as following:

Channel A : DIMM 1, 2

Channel B : DIMM 3, 4

DDR Introduction

Established on the existing SDRAM infrastructure, DDR (Double Data Rate) memory is a high perfor-

mance and cost-effective solution that allows easy adoption for memory vendors, OEMs, and system

integrators.

DDR memory is a great evolutionary solution for the PC industry that builds on the existing

SDRAM architecture, yet make the awesome advances in solving the system performance bottle-

neck by doubling the memory bandwidth. Nowadays, with the highest bandwidth of 3.2GB/s of

DDR400 memory and complete line of DDR400/333/266/200 memory solutions, DDR memory is

the best choice for building high performance and low latency DRAM subsystem that are suitable

for servers, workstations, and full range of desktop PCs.

- 16 -GA-8VT880 Series Motherboard

English

The following tables include all memory-installed combination types:

(If you wish to use memory-installed combination type, please use it in unity with BIOS(FORCE Dual/FORCE

Single/ Auto)

2 memory modules

4 memory modules

DIMM 1 DIMM 2 DIMM 3 DIMM 4

DS/SS X DS/SS X

X DS/SS X DS/SS

DS/SS DS/SS DS/SS DS/SS

l Figure 1: Dual Channel Technology (DS: Double Side, SS: Single Side)

l Figure 2: Single Channel Technology (DS: Double Side, SS: Single Side)

1 memory modules

2 memory modules

DIMM 1 DIMM 2 DIMM 3 DIMM 4

DS/SS X X X

X DS/SS X X

X X DS/SS X

X X X DS/SS

DS/SS DS/SS X X

X X DS/SS DS/SS

DS/SS X X DS/SS

X DS/SS DS/SS X

La pagina sta caricando ...

Gigabyte GA-8VT880-L Manuale utente

Questo manuale è adatto anche per

Gigabyte GA-8VT880-L Manuale utente

in altre lingue

Documenti correlati

Altri documenti