STUDIO DUE CLEVER SPOT PLUG-IN M Manuale utente

Categoria
Illuminazione di comodità
Tipo
Manuale utente

Questo manuale è adatto anche per

User manual
Manuale d’uso
RGBW - MONOCHROMATIC
CleverClever
RDM
spotspot
this page is intentionally left blank / questa pagina è stata lasciata intenzionalmente bianca
rel.1_10/23 - Studio Due
3
INDEX
Page 4 Safety informations / Informazioni di sicurezza
Page 5 Introduction / Introduzione
Page 6 Technical features / Caratteristiche tecniche
Page 9 Main supply connection / Collegamento fonte di alimentazione
Page 10 DMX connections / Connessioni DMX
Page 11 Example of connections DMX-Controller / Esempi di collegamento DMX-Controller
Page 12 Setup and configuration (touch control panel) / Configurazione e settaggio (pannello di controllo touch)
Page 14 DMX Channels list / Lista canali DMX
Page 17 Physical / Dimensioni
Page 18 CE standards / Certificazioni CE
Page 19 Warranty / Garanzia
CLEVER SPOT RGBW CLEVER SPOT MONOCHROMATIC
rel. 1_10/23 - Studio Due 4
.................................................................................................................. ENG
SAFETY INFORMATION (service personnel)
IMPORTANT !
READ ALL CAUTIONS AND WARNINGS PRIOR TO OPERATE THIS EQUIPMENT.
INSTRUCTION TO PREVENT INJURY OR DAMAGE DUE TO ELECTRIC SHOCK, FIRE, MECHANICAL HAZARDS, DANGEROUS MATTERS.
• PROTECTION AGAINST DANGEROUS MATTERS
At the end of its life, must be collected separately. It shouldn’t be thrown as urban waste and neither released in the environment.
It must be collected from the nearest special waste collection point or consigned to your dealer that provides the service.
The incorrect waste disposal can damage the environment and the people for the presence of dangerous substances.
Sanctions are provided for an unauthorized disposal. ............................................................................................................................................................
• PROTECTION AGAINST FIRE
1) Maintain minimum distance of 0,2 meter to lighted objects.
2) Replace fuses (if present) only with the specified type and rating.
3) Do not install the fixture close to heat sources. Do not lay the connection cable on the fixture when it is warm.
4) Fixture designed to be installed on normally flammable surfaces. .....................................................................................................................................
• PROTECTION AGAINST ELECTRIC SHOCK
1) This equipment must be earthed.
2) Class I equipment. The power supply cord includes a protective earthing conductor as part of the cord.
3) Disconnect power before servicing (service personnel).
4) To replace the LEDs, contact: Studio Due Trade Srls.
5) If the external flexible cable of this appliance is damaged, it must only be replaced by the manufacturer,
its assistance service, or equivalent qualified personnel, in order to avoid dangers. ...........................................................................................................
• PROTECTION AGAINST MECHANICAL HAZARDS
1) Use secondary safety chain when fixing this equipment.
2) The protection screens and the lenses must be replaced with genuine parts only if they are visibly damaged and
their effectiveness has been reduced, for example, by cracks or deep scratches.
3) Do not look directly into the illuminated LEDs of the product for long periods of time. LED lamps can cause eye
damage or irritation. Do not look directly into the light source using an optical instrument that focuses on the light beams.
The device should be positioned so that there is no prolonged observation of the device at a distance
of less than 100cm. (RG1 – IEC/TR 62778:2014).
................................................................................................................... ITA
INFORMAZIONI DI SICUREZZA (personale di servizio)
IMPORTANTE !
LEGGERE ATTENTAMENTE TUTTI GLI AVVERTIMENTI PRIMA DI COMPIERE QUALUNQUE OPERAZIONE SU QUESTO APPARECCHIO.
ISTRUZIONI PER PREVENIRE LESIONI O DANNI DOVUTI AL FUOCO, ALLE SCOSSE ELETTRICHE, AI RISCHI MECCANICI ED A SOSTANZE PERICOLOSE.
•PROTEZIONE CONTRO SOSTANZE PERICOLOSE
A fine vita è oggetto di raccolta separata, non gettare nei comuni cassonetti di rifiuti urbani, né tantomeno nell’ambiente.
Può essere consegnato presso i centri di raccolta delle amministrazioni comunali, oppure presso i rivenditori che forniscono questo servizio.
Lo smaltimento errato può causare danni alle persone e all’ambiente per la possibile presenza di sostanze pericolose.
Sono previste sanzioni in caso di smaltimento abusivo dei suddetti prodotti. ..........................................................................................................................
•PROTEZIONE CONTRO IL FUOCO
1) Mantenere la distanza minima di 0,2 metri dagli oggetti illuminati.
2) Sostituire i fusibili (se presenti) solo con altri dello stesso tipo e valore.
3) Non installare il faro vicino fonti di calore. Non appoggiare il cavo di connessione sul faro quando questo è caldo.
4) Questo apparecchio è adatto per il montaggio su superfici normalmente infiammabili. .......................................................................................................
•PROTEZIONE CONTRO SCOSSE ELETTRICHE
1) Questo apparecchio necessita di messa a terra.
2) Apparecchio di Classe I. Il conduttore di protezione deve far parte del cavo di alimentazione.
3) Disconnettere l’alimentazione prima di aprire l’apparecchio (personale di servizio).
4) Per la sostituzione dei LED contattare l’azienda: Studio Due Trade Srls
5) Se il cavo flessibile esterno di questo apparecchio è danneggiato, deve essere sostituito esclusivamente
dal costruttore, dal suo servizio di assistenza, o da personale qualificato equivalente, al fine di evitare pericoli. .................................................................
•PROTEZIONE CONTRO RISCHI MECCANICI
1) Usare la catena di sicurezza supplementare quando installate l’apparecchio.
2) Gli schermi di protezione e le lenti devono essere sostituiti sempre con ricambi originali se sono visibilmente danneggiati
e se la loro efficacia è stata ridotta, per esempio, da fessure o incisioni profonde.
3) Non guardare direttamente nei LED illuminati del prodotto per lunghi periodi di tempo. Le lampade a LED possono
causare danni o irritazione agli occhi. Non guardare direttamente nella sorgente luminosa utilizzando uno strumento
ottico che si concentra sui fasci di luce. L’apparecchio dovrebbe essere posizionato in modo che non sia prevista
un’osservazione prolungata dell’apparecchio ad una distanza inferiore di 100cm. (RG1 – IEC/TR 62778:2014).
rel.1_10/23 - Studio Due
5
.................................................................................................................. ENG
INTRODUCTION
CHECK THAT THE FIXTURE HAS NOT BEEN DAMAGED DURING TRANSPORT. IF IT HAS BEEN DAMAGED OR IT DOES NOT WORK, ADDRESS THE
SELLER. WHETHER THE FIXTURE HAS BEEN SHIPPED TO YOU DIRECTLY, PLEASE CONTACT THE SHIPPING COMPANY.
ONLY THE CONSIGNEE (PERSON OR COMPANY) CAN CLAIM FOR THESE DAMAGES.
Thank you for choosing one of the CLEVER SPOT series appliances, our small and compact IP67 projector. Suitable for permanent architectural installations,
is flexible for mounting on poles, walls or on the ground.
RDM control and configuration. RGBW or Monochromatic version. Plug-in version.
• Standard fixture colour finishing is grey RAL 9006 (standard)
Optional: Black RAL 9005 - White RAL 9010 - Any RAL.
• Art. 220810 CLEVER SPOT RGBW
• Art. 220820 CLEVER SPOT M RDM (monochromatic)
• Art. 220800 CLEVER SPOT PLUG-IN M (monochromatic)
To obtain the best performances and for a correct functioning of this unit for the years to come, we suggest you to read carefully this manual before
connecting or putting the fixture into use. By doing so you will gain experience with its commands and connections and you will be easily able to use it.
YOUR REFERENCE
Always remember to give the serial number and to specify the model any time you address the seller for information or assistance.
BASIC KIT
• Fixture
• Main Power: 3x0,75mm cable
• DMX signal: 3pin IP67 connector (male-female)
• User manual
• Studio Due warranty
• CE standards
................................................................................................................... ITA
INTRODUZIONE
CONTROLLATE CHE L’APPARECCHIO NON ABBIA SUBITO ALCUN DANNO DURANTE IL TRASPORTO. SE AVESSE SUBITO DEI DANNI O SE NON DOVESSE
FUNZIONARE, RIVOLGETEVI AL VOSTRO RIVENDITORE. SE L’APPARECCHIO VI È STATO SPEDITO DIRETTAMENTE, RIVOLGETEVI SUBITO ALLA DITTA DI
TRASPORTO.
SOLO IL DESTINATARIO (LA PERSONA O DITTA RICEVENTE L’APPARECCHIO) PUÒ RECLAMARE PER QUESTO TIPO DI DANNI.
Grazie per aver scelto uno degli apparecchi della serie CLEVER SPOT, il nostro piccolo e compatto proiettore IP67. Adatto per installazioni architettoniche
permanenti, è ideale per il montaggio su pali, pareti o sul terreno.
Controllo e configurazione RDM versione RGBW o Monocromatico. Versione Plug-in.
• Finitura standard colore grigio RAL 9006 (standard)
Optional: Nero RAL 9005 - Bianco RAL 9010 - Qualsiasi RAL
• Art. 220810 CLEVER SPOT RGBW
• Art. 220820 CLEVER SPOT M RDM (monochromatic)
• Art. 220800 CLEVER SPOT PLUG-IN M (monochromatic)
Per ottenere il meglio delle prestazioni ed un corretto funzionamento negli anni di questa unità, Vi consigliamo di leggere attentamente questo manuale
prima di collegarla e metterla in uso. In questo modo acquisirete familiarità con i suoi comandi e collegamenti affinché possiate utilizzarla facilmente.
VOSTRA REFERENZA
Citate sempre il numero del modello e di serie ogni volta che Vi rivolgete al vostro rivenditore per informazioni o assistenza.
CONFEZIONE BASE
• Apparecchio
• Ingresso Rete: 3x0,75mm
• Segnale DMX: connettore 3pin IP67 (maschio-femmina)
• Manuale d’uso
• Garanzia Studio Due
• Dichiarazione CE
OPTIONAL ACCESSORIES
- Snoot
ACCESSORI OPZIONALI
- Snoot
rel. 1_10/23 - Studio Due 6
.................................................................................................................. ENG / ITA
TECHNICAL FEATURES / CARATTERISTICHE TECNICHE
CLEVER SPOT RGBW (art.220810)
Small wash LED spot with 7 RGBW full color LEDs. Remote configura�on by
DRS Setup device. IP 67 protection rating.
Technical Specification
LED type RGBW multi-chip with white 4000K
Number of LEDs 7
LED expected lifetime (hrs) 50000
Lumen MAX 865
Red lumen (lm) 210
Green lumen (lm) 330
Blu lumen (lm) 130
White lumen (lm) 325
CRI >80
Lenses 10°x30°
12°
24°
30°x10°
36°
Filters None
f 30°
f 60°
f 80°
f 12°x 60°
Connectors and cables Main Power: 3x0,75mm cable
DMX signal: 3pin IP67 connector (male-female)
Control type Protocol USITT DMX512 - RDM
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
Functions Dedicated DMX channel for white balance from 2000K to 10000K
DMX or Auto Mode with Master-Slave function
Intelligent temperature control
Continuous dimming 0-100%
Smooth dimming function
Halogen simulation
CYM simulation
Flicker-free function
Setup RDM/DRS
DMX channels 10ch - 9ch - 4ch
Input range 100 - 277 VAC; 47/63 Hz
Power (W) 15
Current 0,1@230VAC
Inrush current 45A@230V
Tilt 360°
IP protection rating 67
IK grade protection 07
Operating temperature -30°C +45°C
Sizes l x p x h (mm) 165 x 70 x 160
Weight (Kgs) 1,1
Materials Ultra clear 4mm tempered glass
PMMA lenses
All aluminium alloy
Polyester powder coated
Mounting systems Surface
Truss (optional)
Colour finishing Grey RAL 9006 (standard)
Black RAL 9005 (optional)
White RAL 9010 (optional)
Any RAL (optional)
Marine Grade treatment None
Yes
Product Category Spot
Accessories - Snoot None
Yes
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
2 / 3
CLEVER SPOT RGBW (art.220810)
Small wash LED spot with 7 RGBW full color LEDs. Remote configura�on by
DRS Setup device. IP 67 protection rating.
Technical Specification
LED type RGBW multi-chip with white 4000K
Number of LEDs 7
LED expected lifetime (hrs) 50000
Lumen MAX 865
Red lumen (lm) 210
Green lumen (lm) 330
Blu lumen (lm) 130
White lumen (lm) 325
CRI >80
Lenses 10°x30°
12°
24°
30°x10°
36°
Filters None
f 30°
f 60°
f 80°
f 12°x 60°
Connectors and cables Main Power: 3x0,75mm cable
DMX signal: 3pin IP67 connector (male-female)
Control type Protocol USITT DMX512 - RDM
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
rel.1_10/23 - Studio Due
7
WW W
warm neutral cool
BGR A
.................................................................................................................. ENG / ITA
TECHNICAL FEATURES / CARATTERISTICHE TECNICHE
CLEVER SPOT M RDM (it. 220820)
Small wash LED spot with 4 High Power Monochroma�c LEDs. Remote
configuration by DRSW Setup device. IP 67 protection rating.
Technical Specification
LED type WHITE 2700 K
BIANCO 3000 K
WHITE 4000 K
WHITE 6500 K
RED
GREEN
BLUE
AMBER
Number of LEDs 4 White 4000K LEDs 3535 1.8A max
LED expected lifetime (hrs) 50000
Lumen MAX 1800
Lenses 4°
10°x30°
15°
25°
40°
60°
Filters None
f 30°
f 60°
f 80°
f 4° x 60°
Connectors and cables Main Power: 3x0,75mm cable
DMX signal: 3pin IP67 connector (male-female)
Control type Protocol USITT DMX512 - RDM
Functions DMX or Auto Mode with Master-Slave function
Intelligent temperature control
Continuous dimming 0-100%
Smooth dimming function
Halogen simulation
Flicker-free function
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
DMX channels 3ch - 1ch
Input range 100 - 277 VAC; 47/63 Hz
Power (W) 13
Current 60mA@230VAC
Inrush current 45A@230V
Tilt 360°
IP protection rating 67
IK grade protection 07
Operating temperature -30°C +45°C
Sizes l x p x h (mm) 165 x 70 x 160
Weight (Kgs) 1,1
Materials Ultra clear 4mm tempered glass
PMMA lenses
All aluminium alloy
Polyester powder coated
Mounting systems Surface
Truss (optional)
Colour finishing Grey RAL 9006 (standard)
Black RAL 9005 (optional)
White RAL 9010 (optional)
Any RAL (optional)
Marine Grade treatment None
Yes
Product Category Spot
Accessories - Snoot None
Yes
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
2 / 3
CLEVER SPOT M RDM (it. 220820)
Small wash LED spot with 4 High Power Monochroma�c LEDs. Remote
configuration by DRSW Setup device. IP 67 protection rating.
Technical Specification
LED type WHITE 2700 K
BIANCO 3000 K
WHITE 4000 K
WHITE 6500 K
RED
GREEN
BLUE
AMBER
Number of LEDs 4 White 4000K LEDs 3535 1.8A max
LED expected lifetime (hrs) 50000
Lumen MAX 1800
Lenses 4°
10°x30°
15°
25°
40°
60°
Filters None
f 30°
f 60°
f 80°
f 4° x 60°
Connectors and cables Main Power: 3x0,75mm cable
DMX signal: 3pin IP67 connector (male-female)
Control type Protocol USITT DMX512 - RDM
Functions DMX or Auto Mode with Master-Slave function
Intelligent temperature control
Continuous dimming 0-100%
Smooth dimming function
Halogen simulation
Flicker-free function
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
rel. 1_10/23 - Studio Due 8
WW W
warm neutral cool
BGR A
.................................................................................................................. ENG / ITA
TECHNICAL FEATURES / CARATTERISTICHE TECNICHE
CLEVER SPOT PLUG-IN M (art.220800)
Small wash LED spot with 4 High Power Monochroma�c LEDs. PLUG-IN
version. IP 67 protection rating.
Technical Specification
LED type WHITE 2700 K
BIANCO 3000 K
WHITE 4000 K
WHITE 6500 K
RED
GREEN
BLUE
AMBER
Number of LEDs 4 White 4000K LEDs 3535 1.8A max
LED expected lifetime (hrs) 50000
Lumen MAX 1800
Lenses 4°
10°x30°
15°
25°
40°
60°
Filters None
f 30°
f 60°
f 80°
f 4° x 60°
Connectors and cables Main Power: 3x0,75mm cable
Control type Plug-in
Input range 100 - 277 VAC; 47/63 Hz
Power (W) 13
Current 60mA@230VAC
Inrush current 45A@230V
Tilt 360°
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
IP protection rating 67
IK grade protection 07
Operating temperature -30°C +45°C
Sizes l x p x h (mm) 165 x 70 x 160
Weight (Kgs) 1,1
Materials Ultra clear 4mm tempered glass
PMMA lenses
All aluminium alloy
Polyester powder coated
Mounting systems Surface
Truss (optional)
Colour finishing Grey RAL 9006 (standard)
Black RAL 9005 (optional)
White RAL 9010 (optional)
Any RAL (optional)
Marine Grade treatment None
Yes
Product Category Spot
Accessories - Snoot None
Yes
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
2 / 3
CLEVER SPOT PLUG-IN M (art.220800)
Small wash LED spot with 4 High Power Monochroma�c LEDs. PLUG-IN
version. IP 67 protection rating.
Technical Specification
LED type WHITE 2700 K
BIANCO 3000 K
WHITE 4000 K
WHITE 6500 K
RED
GREEN
BLUE
AMBER
Number of LEDs 4 White 4000K LEDs 3535 1.8A max
LED expected lifetime (hrs) 50000
Lumen MAX 1800
Lenses 4°
10°x30°
15°
25°
40°
60°
Filters None
f 30°
f 60°
f 80°
f 4° x 60°
Connectors and cables Main Power: 3x0,75mm cable
Control type Plug-in
Input range 100 - 277 VAC; 47/63 Hz
Power (W) 13
Current 60mA@230VAC
Inrush current 45A@230V
Tilt 360°
Studio Due Trade S.r.l.
Sede operativa: Strada Poggino, 100 - 01100 Viterbo (I)
IT14078001006
1 / 3
rel.1_10/23 - Studio Due
9
.................................................................................................................. ENG / ITA
CONNECTION TO THE MAIN POWER / CONNESSIONE ALLA RETE ELETTRICA
This equipment must be earthed.
Class I equipment. The power supply cord includes a protective earthing conductor as part of the cord.
IMPORTANT: to ensure the protection rating of the fixture, in case of replacement of the conductor cable, refer to the CONDUCTOR SIZE TABLE
Questo apparecchio necessita di messa a terra.
Apparecchio di Classe I. Il conduttore di protezione deve far parte del cavo di alimentazione.
IMPORTANTE: per garantire il grado di protezione dell’apparecchio, in caso di sostituzione del cavo di alimentazione, fare riferimento alla TABELLA
SEZIONE CONDUTTORE.
ATTENTION - HIGH VOLTAGE!
ALWAYS DISCONNECT THE MAINS SUPPLY BEFORE ACCESS TO THE CONNECTION AREA.
ATTENZIONE - ALTA TENSIONE!
SCOLLEGARE SEMPRE L’ALIMENTAZIONE PRIMA DI APRIRE IL VANO DEI COLLEGAMENTI.
MAIN IN
Ingresso rete
BROWN / 100/277Vac - 50-60Hz
BLUE / NEUTRAL
GREEN-YELLOW / GROUND
MAIN IN CONNECTION
UNIVERSAL MAIN VOLTAGE
100-277V~ /50-60Hz
PIN SIGNAL
(L) Live
(N) Neutral
(G) Ground
Metal
Anti-Condensation
Valve
CONDUCTOR SIZES / SEZIONE CONDUTTORE
(length / lunghezza < 20mt.)
MAINS VOLTAGE CROSS SELECTIONAL AREAS
230V 3X1 mm2 (minimum)
POWER INPUT / INGRESSO ALIMENTAZIONE
The Cable Gland can accept a Cable diameter from 6mm to 10mm
Il Pressacavo può accettare Cavi di diametro da 6mm a 10mm
rel. 1_10/23 - Studio Due 10
DMX IN/OUT
.................................................................................................................. ENG / ITA
CONNECTION TO THE DMX SIGNAL / CONNESSIONE AL SEGNALE DMX
DMX TERMINAL LINE
The wrong connection of the terminal line or its non-connection are probably the most frequent reasons of the lower DMX
signal.
The terminator is a terminal resistor fitted at the end of the cable. (see pict. 1)
The terminal resistor should have the same value as the impedance of the connection cable (120 Ohm).
It is recommanded that all DMX 512 systems have the terminal resistor fitted in the end of DMX line.
TERMINALE LINEA DMX
L’incorretto o il mancato collegamento del terminale di linea è probabilmente la più comune causa del difettoso funzionamento
della linea DMX.
Il terminale di linea DMX consiste in una resistenza posta alla fine della linea. (vedere fig. 1)
La resistenza terminale dovrebbe avere lo stesso valore dell’impedenza del cavo di collegamento (120 Ohm).
E’ raccomandato per tutti i sistemi DMX 512, di inserire il teminale di linea nel connettore di uscita DMX dell’ultimo apparecchio
collegato.
PIN
1SHIELD GROUND/RETURN/OV
2 )DETREVNI,-(TNEMELPMOCATADROTCUDNOCRENNI
3 INNER CONDUCTOR DATA TRUE ( +, NON INVERTED)
DMX inputDMX output
Termination resistor
Terminale di linea
120 Ohm
DMX inputDMX output
120 Ohm
Termination resistor
Terminale di linea
PIN
1SHIELD GROUND/RETURN/OV
2 )DETREVNI,-(TNEMELPMOCATADROTCUDNOCRENNI
3 INNER CONDUCTOR DATA TRUE ( +, NON INVERTED)
DMX inputDMX output
Termination resistor
Terminale di linea
120 Ohm
DMX inputDMX output
120 Ohm
Termination resistor
Terminale di linea
pict. 1
PIN
1SHIELD GROUND/RETURN/OV
2 )DETREVNI,-(TNEMELPMOCATADROTCUDNOCRENNI
3 INNER CONDUCTOR DATA TRUE ( +, NON INVERTED)
DMX inputDMX output
Termination resistor
Terminale di linea
120 Ohm
DMX inputDMX output
120 Ohm
Termination resistor
Terminale di linea
1
2
3
ø 14mm
Female connector
ø 14mm
Male connector
rel.1_10/23 - Studio Due
11
.................................................................................................................. ENG / ITA
EXAMPLE OF CONNECTION DMX CONTROLLER - FIXTURES / ESEMPIO DI COLLEGAMENTO CENTRALINA - FARI
DMX
fixture 1 fixture 2 fixture 3 fixture 4
TL
NORMAL
Address
set-up 4ch
=C001
Address
set-up 4ch
=C005
Address
set-up 4ch
=C009
Address
set-up 4ch
=C013
fixture 2 fixture 3 fixture 4
TL
MASTER / SLAVE
Set up = MASTER set-up = SLAVE set-up = SLAVE set-up = SLAVE
fixture 1
NORMAL AND MASTER/SLAVE FUNCTIONS / FUNZIONI NORMAL E MASTER/SLAVE
Example 1/ Esempio 1
DMX
Last fixture/
Ultimo apparecchio
Termination resistor/
Terminale di linea
Example 2 / Esempio 2
DMX
line 1 / linea 1
line 2 / linea 2
DMX 1 out DMX 2 out
Connection controller-spot to
1 DMX 512 output over 150 mt. long
Collegamento centralina-spot ad una sola
linea di uscita DMX 512 lunga oltre 150 mt.
LINE > 150 mt. (with microphonic or audio cable)
LINEA > 150 mt. (con cavo microfonico o audio)
DMX
Example 3 / Esempio 3
SIGNAL AMPLIFIER
AMPLIFICATORE
DI SEGNALE
DMX out
DMX out
TL=
Terminal Line
for example fixture set-up at 4 channels
TL
TL
TL
TL
fixture /
apparecchio
fixture /
apparecchio fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio
fixture /
apparecchio fixture /
apparecchio
fixture /
apparecchio
Last fixture/
Ultimo apparecchio
Termination resistor/
Terminale di linea
fixture /
apparecchio
fixture /
apparecchio fixture /
apparecchio
fixture /
apparecchio
Last fixture/
Ultimo apparecchio
Termination resistor/
Terminale di linea
Last fixture/
Ultimo apparecchio
Termination resistor/
Terminale di linea
fixture /
apparecchio fixture /
apparecchio
rel. 1_10/23 - Studio Due 12
.................................................................................................................. ENG
SETUP AND CONFIGURATION BY DRS - DMX REMOTE SETUP
The DRS it’s a new concept of professional LED Lighting fixtures suitable for outdoor permanent installations.
The LED Lighting fixtures can be driven via DMX through a specific electronic device, the DRS DMX Remote Setup, that grant the
possibility to set up the scenarios and the games remotely.
These LED Lighting fixtures have installed on board a series of programs including the stand alone function.
The DRS is a simple set up commander that linked with the DMX input of a LED Lighting fixture allow to program all the functions of the luminaire.
It’s than possible to assign the DMX channel or use the Master/Slave function.
The device is powered through battery.
DRS è il nuovo concetto dell’illuminazione LED per uso professionale nelle installazioni esterne permanenti.
Gli apparecchi LED possono essere controllati e configurati tramite uno specifico controller: il DRS, DMX Remote Setup, il quale consente di programmare e
configurare scene e giochi di luce in modalità remota.
Questi apparecchi LED hanno installati a bordo una serie di giochi che includono la funzione stand alone.
Il DRS, DMX Remote Setup, è un semplice set-up commander che collegato via DMX ad un’apparecchio consente la sua programmazione e configurazione.
E’ possibile assegnare agli apprecchi collegati i canali DMX o utilizzazre la funzione Master/Slave.
Il DRS è alimentato a batterie.
DMX line
XRL - LLT
connector
MAIN Power
Powered through
battery
RDM CONSOLE
.................................................................................................................. ITA
SETTAGGIO E CONFIGURAZIONE TRAMITE DRS - DMX REMOTE SETUP
rel.1_10/23 - Studio Due
13
.................................................................................................................. ITA
SETTAGGIO E CONFIGURAZIONE TRAMITE DRS - DMX REMOTE SETUP
Per effettuare la programmazione dei vari parametri di un apparecchio, è necessario procedere come segue:
• Disconnettere l’apparecchio da configurare da altri dispositivi DMX/RDM
• Collegare il cavo DMX dell’apparecchio da configurare, al programmatore DRS
• Accendere il programmatore DRS ed attendere che visualizzi la scritta 8888
• Se il programmatore DRS individua un dispositivo DRS compatibile, visualizza per qualche istante la scritta Conn e,
successivamente, visualizza il nome dell’apparecchio e la relativa versione software
• Se il programmatore DRS non individua alcun dispositivo DRS compatibile o è presente qualche malfunzionamento il display
visualizzerà la scritta SCAn
• Una volta terminata la sequenza di riconoscimento, viene visualizzato il primo menu dell’apparecchio
• I pulsanti UP/DOWN permettono di scorrere la lista dei menu
Il pulsante ENTER permettere di entrare in un menu o di confermare una opzione in caso di lampeggio del parametro
• Il pulsante ESC annulla una operazione o torna al livello di menu inferiore.
.................................................................................................................. ENG
SETUP AND CONFIGURATION BY DRS - DMX REMOTE SETUP
To make the set-up of the various fixture parameter, proceed as follow:
•Disconnect the fixture to set-up from the other DMX/RDM devices
• Connect the DMX cable of the fixture to the DRS commander
Switch on the DRS commander and wait for the 8888 sign
If the DRS commander detects a compatible DRS device, displays shortly the Conn written and afterwards,
displays the name of the fixture and its software version.
If the DRS commander dont’ detects any compatible DRS device or is present any malfunction, the display
shows the SCAn written
When the detection sequence is finished, the display shows the first menu
The UP/DOWN buttons allow to scroll forward/backward the menu list
The ENTER button allow to confirm the selected option (if the parameter is flashing)
• The ESC button allow to delete the operation and return to a previus menu level
dimmable version only / solo versione dimmerabile
rel. 1_10/23 - Studio Due 14
Switching on the fixture you can see the model and the software version. For example:
All’accensione, viene visualizzato il modello di apparecchio e la versione software. Per esempio:
--> MEGAW... --> 1_00 - than it’s shown the fist menu / poi viene visualizzato il primo menu
Address (Addr) Set the DMX channel address / Imposta il canale DMX
> Select the channel number .. c001 .. c002 .. whit the UP/DOWN buttons. Press ENTER.
> Selezionate il canale desidarato .. c001 .. c002 .. con i tasti UP/DOWN. Premere ENTER.
Auto Mode (ModE) Set the DMX, SLAVE or MASTER mode / Imposta la modalità DMX, SLAVE o MASTER
> Select the value no .. sl .. pr01 .. pr02 .. with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desidarato no .. sl .. pr01 .. pr02 .. con i tasti UP/DOWN. Premere ENTER.
Auto Speed (PrSP) Set the preset execution speed / Imposta la velocità di esecuzione dei giochi interni
> Select the value +400% .. -400% with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desiderato +400% .. -400% con i tasti UP/DOWN. Premere ENTER.
Wireless enable (ULEn) Enable or disable the wireless reception / Consente o non consente la ricezione wireless. (ON, OFF)
The cable reception is disabled / La ricezione via cavo viene disabilita
> Select the value on .. off .. with the UP/DOWN buttons. The written is flashing, press ENTER.
> Selezionate il valore desidarato on .. off .. con i tasti UP/DOWN. La scritta lampeggia, premere ENTER.
Wireless unlink (ULPA) Remove the link from the fixture to the associated transmitter (PA?). Press ENTER.
Elimina il link tra l’apparecchio e il trasmettitore al quale è stato associato. Premere ENTER.
Wireless bridge (ULbr) If wireless is ON, enable the transmission of the received data by cable to the other fixtures
Se il wireless è attivo, consente la trasmissione dati agli altri apprecchi collegati via cavo. (ON, OFF)
> Select the value on .. off .. with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desidarato on .. off .. con i tasti UP/DOWN. Premere ENTER.
Scene (Scne)
N. Channels (nChn) Set the DMX channels of the fixture / Imposta il numero di canali DMX dell’apparecchio. (10, 7, 6, 5)
> Select the value, e.g. .. 7.. 5 etc. with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desidarato, per esempio .. 7 .. 5 etc. con i tasti UP/DOWN. Premere ENTER.
Flicker free function (FLcr) Flicker free function / Funzione flicker free. (F1, F2)
> Select the value f1 .. f2
> Selezionate il valore desidarato f1 .. f2
.................................................................................................................. ENG / ITA
DRS MENU’ LIST / ELENCO MENU DRS
If ON: For each color or menu it is possible to varying and than set-up the value from
0 to 255 without having to confirm with the ENTER key.
These functions are auto-save.
Se ON: Per ogni singolo colore o menu, è possibile variare e quindi impostare il
valore da 0 a 255 senza dover confermare con il tasto ENTER.
Queste funzioni si salvano automaticamente.
ch1
ch2
ch3
ch4
ch5
ch6
rel.1_10/23 - Studio Due
15
DMX Channels list 9Ch / Lista dei canali DMX 9Ch
8 BIT FUNCTION 0 31 63 95 127 159 191 233 255
CH1 RED
CH2 GREEN
CH3 BLUE
CH4 WHITE
CH5 STROBE
FLASH 0,4Hz / 25Hz
2 -127
OPEN
0 - 1
RAINBOW - FLASH 0,4Hz / 25Hz
128 -255
CH6 DIMMER
CH7 LED FADE
TIME
FAST - 0,1 sec.
0 = CUT SLOW
25,5 sec.
LINEAR
CH8 RAINBOW
CH9 BALANCED
WHITE 0 - 15 NORMAL 16 - 255
WW CW
Smooth Dimming (SMth) Set the interpolation type for the smooth dimming function
Imposta il tipo di interpolazione per la funzione smooth dimming. (OFF, Sd1, Sd2, Sd3)
> Select the value oFF .. LoW .. MId .. hIGh with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desidarato oFF .. LoW .. MId .. hIGh con i tasti UP/DOWN. Premere ENTER.
Halogen Simulation (HALS) Set the alogen simulation function mode
Imposta il funzionamento della modalità simulazione lampada alogena. (OFF, Mod1, Mod2)
> Select the value oFF .. MId1 .. MId2 with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desiderato oFF .. MId1 .. MId2 con i tasti UP/DOWN. Premere ENTER.
CYM Emulation (CYMS) Set the fixture to work in CYM or RGB emulation system
Imposta l’apparecchio per funzionare come emulatore di sistema CYM o RGB. (CYM, RGB)
> Select the value off >> RGB or on >> CYM with the UP/DOWN buttons. Press ENTER.
> Selezionate il valore desiderato off >> RGB oppure on >> CYM con i tasti UP/DOWN. Premere ENTER.
Test (tESt) Enables the test of the fixture and execute a factory program to check the right functioning/
Abilita il test dell’apparecchio ed esegue un programma di fabbrica per verificarne il funzionamento. (T-ON)
> Select the value t-on with the UP/DOWN buttons. T-on is flashing: test in progress. Press any key to exit.
> Selezionate il valore t-on con i tasti UP/DOWN. T-on lampeggia: test in corso. Premere qualsiasi tasto per uscire.
Reset (rSEt) Execute a reset of the electronic section / Esegue un reset della parte elettronica. (rS?)
Format (FrMt) Restore the factory setting (Require confirmation).
Ripristina le impostazioni di fabbrica (Viene chiesta conferma). (Fm?)
rel. 1_10/23 - Studio Due 16
DMX Channels list 5Ch / Lista dei canali DMX 5Ch
DMX Channels list 4Ch / Lista dei canali DMX 4Ch
8 BIT FUNCTION 0 31 63 95 127 159 191 233 255
CH1 RED
CH2 GREEN
CH3 BLUE
CH4 WHITE
CH5 DIMMER
8 BIT FUNCTION 0 31 63 95 127 159 191 233 255
CH1 RED
CH2 GREEN
CH3 BLUE
CH4 WHITE
rel.1_10/23 - Studio Due
17
DMX
512
DMX
512
8 BIT FUNCTION 0 31 63 95 127 159 191 233 255
CH1 DIMMER
CH2 STROBE
FLASH 0,4Hz / 25Hz
2 -127
OPEN
0 - 1
RAINBOW - FLASH 0,4Hz / 25Hz
128 -255
CH3 LED FADE
TIME
FAST - 0,1 sec.
0 = CUT SLOW
25,5 sec.
LINEAR
8 BIT FUNCTION 0 31 63 95 127 159 191 233 255
CH1 DIMMER
.................................................................................................................. ENG / ITA
DMX CHANNELS MONOCHROMATIC / CANALI DMX MONOCROMATICO
- (*) DMX line for Dimmable version. (setting 3ch or 1ch)
--------------------------------------------------------------------------------------------------------------
- (*) linea DMX versione Dimmerabile. (settaggio 3ch o 1ch)
PHYSICAL / DIMENSIONI
165
160
70
Ø 1020x10
160
40
rel. 1_10/23 - Studio Due 18
Art. 220810 CLEVER SPOT RGBW
Art. 220820 CLEVER SPOT M RDM (monochromatic)
Art. 220800 CLEVER SPOT PLUG-IN M (monochromatic)
VITERBO, 10/05/23
23
Data di apposizione:
Date of marking:
Doc. 2208 REV 1 - 05/23
CLEVER SPOT
IP67
EMC Directive: 2014/30/EU
EN 55103-1:2009 + A1:2012
EN 55015:2014
EN 55103-2:2009
EN 61547:2009
EN 61000-3-2:2014
EN 61000-3-3:2013
Low Voltage Directive: 2014/35/EU
EN 60598-1:2015
EN 62471:2008
EN 60529:1991 + A1:2000 + A2:2013
EN 60598.2.5:2015
ROBERTO FRAIOLI
General Manager
2011/65/EU: RoHS2 Directive
La ditta:
The firm:
dichiara sotto la propria responsabilità che il prodotto:
declare under our sole responsability that the product:
Studio Due Trade s.r.l.
Dichiarazione di conformità
Declaration of conformity
Studio Due Trade s.r.l.
R.E.A. 1494819 ∙ C.F. / P. Iva 14078001006
legal seat: via Raffaele Battistini, 35 ∙ 00151 Roma
operational headquarters: str. Poggino, 100 ∙ 01100 Viterbo (Italy)
tel. 0761.352520 ∙ fax. 0761.352653
è conforme alle norme:
is in conformity with the standard:
rel.1_10/23 - Studio Due
19
Warranty CARD
WARRANTY / GARANZIA
Company name: ................................................................................................................................
Mr./Mrs./Miss: ..................................................................................................................................
Address: ............................................................................................................................................
Tel. or E-mail : ..................................................................................................................................
Dealer: .............................................................................................
SALE CONDITIONS
1) Price quoted are not inclusive of lamp and package.
Package charge is 2% on the net price for all the items.
These prices should be subject to possible variations for eventual rises of production costs or duties.
The goods travel at the expense, risk and peril of the customer.
Claims for possible damages during the freight, must be notified to the carrier.
Any claim must be notified within 8 days from the recept of the goods.
The buyer is responsable of the right installation and use of the apparatus.
All the apparatuses are guaranteed for one year against defects of manifacture or materials.
Defects and breakeges caused by wrong connection or use of the apparatuses are not subject to guarantee.
The lamp is excluded from the warranty.
For any dispute is competent the Tribunal of Viterbo.
CONDIZIONI DI VENDITA
1) I prezzi riportati sono esclusi di IVA, lampada ed imballaggio.
Il costo di imballaggio è del 2% sul prezzo netto per tutti gli articoli.
Detti prezzi possono essere soggetti a possibili variazioni per eventuali aumenti dei costi di produzione o imposte.
La merce viaggia a rischio e pericolo del committente, anche se in porto franco.
Reclami per possibili danni durante il trasporto, dovranno essere fatti esclusivamente al vettore.
Eventuali osservazioni sulle merci ricevute dovranno esserci notificate entro e non oltre 8 giorni dal ricevimento delle medesime. Sui ritardi dei pagamenti
verrà conteggiato l’interesse commerciale.
L’acquirente si impegna a comunicare la propria esatta ragione sociale e partita IVA al momento dell’ordine e sotto la propria responsabilità di verificarla in
fattura.
L’acquirente è responsabile della corretta installazione ed uso delle apparecchiature.
Tutte le apparecchiature godono della garanzia di un anno contro difetti di fabbricazione o di materiali, sono esclusi dalla garanzia danni derivanti da un cattivo
uso o installazione delle apparecchiature.
Le lampade restano comunque escluse dalla garanzia.
Per ogni controversia è competente il Foro di Viterbo.
Studio Due - ©
The features on this brochure are not binding: they can be changed without notice.
Le caratteristiche riportate su questo catalogo non sono impegnative: possono essere soggette a variazioni senza preavviso.
Head Office: STUDIO DUE s.r.l. (I)
Str. Poggino, 100 - 01100 Viterbo (Italy)
tel. +39.0761.352520
fax +39.0761.352653
www.studiodue.com
for technical info
STUDIO DUE (UK)
3 Encon Court Owl Close
Moulton Park Industrial Estate
Northampton England UK - NN3 6 HZ
tel. +44.1933.650.820
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

STUDIO DUE CLEVER SPOT PLUG-IN M Manuale utente

Categoria
Illuminazione di comodità
Tipo
Manuale utente
Questo manuale è adatto anche per