XR 8 SPOT XR 8 SPOT
GB
User Manual Rel 1.0
Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S.
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione
dei prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or
circuits described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand soin.
Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits réservés. Ce
document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement, sans le
consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado o
reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
ARC 1200
XR 8 SPOT
2
ARC 1200
XR 8 SPOT
3
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 5
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
3- MOUNTING THE LAMP 6
3.1 Lamp alignment
4- VOLTAGE AND FREQUENCY 7
5- INSTALLATION 7
5.1 Safety cable
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION 8
6.1 Protection
7- DMX SIGNAL CONNECTION 9
7.1 DMX Addresses
7.2 Selecting the DMX address
8- DISPLAY FUNCTIONS 11
9- AUTOMATIC MODE 14
9.1 Game P
9.2 Rec Mode
10- PAN & TILT SPEED 15
11- FANS SPEED
12- ERROR MESSAGES
13- HIDDEN MENU 16
14- OPENING UP THE PROJECTOR HOUSING 17
15- REPLACING GOBOS
16- PERIODIC CLEANING 18
16.1 Lenses and reflectors
16.2 Fans and air passages
17- PERIODIC CONTROLS
18- DMX PROTOCOLS 19
19- GOBO WHEEL 30
20-COLOUR WHEEL 31
21- MOTORS CONTROL CARD 32
22- PAN & TILT CARD 33
23-CABLES RESEND CARD
24-DISPLAY CARD
25- LAMP ON-OFF CONTROL CARD
26- WIRING DIAGRAM 34
ARC 1200
XR 8 SPOT
4
1- TECHNICAL FEATURES
The XR 8 Spot is fitted with a Philips MSR 575/2 discharge lamp
(GX9,5 lampholder base), with a colour temperature of 7,200 °K and a luminous flux of
49,000 Lumens.
Duration is 750 hours, with replacement recommended before 1000 hours
Other recommended lamps: Philips 575 MSD (6.000K°-49.000 Lumens-3.000 hours)
The unit incorporates:
Motorized Focus system
Zoom (3 selectable beam aperture angles 11° / 15° / 18° with auto-focus)
Dimmer (emitted light is controlled by progressive and linear dimming).
Shutter (instantaneous shutter opening/closure)
Strobe: mechanical strobe effect (frequency variable from 0.85 flashes/sec to 10
flashes/sec).
Gobo wheel (7 indexable 16 bit gobos + open)
Colour wheel (8 colours + open)
Prism (indexable 3 facet prism rotating in both directions)
Frost Filter
Electronic or magnetic ballast
Pan: 540° in 3.9 seconds (8 or 16 bit) with auto repositioning system
Tilt: 320° in 2.6 seconds (8 or 16 bit) with auto repositioning system
USITT Standard DMX 512 input
20 DMX channels
4 -eight digit- LED display with 4 buttons
2 XLR connectors (In and Out) with 3 and 5 pins selectable by user
Power supply
Electronic ballast:
Universal power supply 90 - 245 V (50/60 Hz)
Electromagnetic ballast:
230 V 50-60 Hz
Power consumption: 750 W.
Remote Lamp on/off via DMX
Operating ambient temperature -10° / 40°
Weight
26 Kg (XR8 SPOT E.B.)
Dimensions (HxDxL)
Projector (670x450x470)
Weight 26 Kg
Packing Dimensions
(HxDxL)
800 x 550 x 440 mm
Weight
33.3 Kg
ARC 1200
XR 8 SPOT
5
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology present in the XR8 requires the assistance of specialised personnel for all
servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20.
XR8 uses a Philips 575 MSR/2 or MSD
3- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
1) Using a screwdriver, remove the 3 screws A,B, C, (photo 1) which fix the lamp holder.
2) Remove the lamp holder assembly (photo2).
3)Insert the lamp (photo 3).
The lamp used on XR 8 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The GX9,5 lamp socket is symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
4) Replace the lamp assembly and tighten the screws A,B,C, which were previously removed (photo4).
3.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.
Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.
Philips 575 MSR/2
Power 575W
Luminous flux 49,000 lm
Colour temperature 7.200°K
Lampbase GX9,5
Rated life 1,000 hours
6
Photo 2Photo 1 Photo 4Photo 3
Philips 575 MSD
Power 575W
Luminous flux 43,000 lm
Colour temperature 6.000°K
Lampbase GX9,5
Rated life 3,000 hours
Photo 5
XR 8 SPOT
4- VOLTAGE AND FREQUENCY
The XR 8 with electronic ballast can operate at 90-245 VOLT 50 or 60 Hz.
The XR 8 with electromagnetic ballast can operate at 230 VOLT 50 or 60 Hz.
5- INSTALLATION
XR8 may be either floor or ceiling mounted.
For floor mounting installations, the XR8 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR8 is moving.
Four quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps
provided in the box, to fix the unit in any position.
.
5.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR8 and to the suspension truss in
order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.
5.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
7
XR 8 SPOT
A
5.3- Movement
The projector has a maximum movement of 540° for Pan and 319° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
5.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.
5.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
5.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
6- MAINS CONNECTION
XR 8 with electronic ballast operate at 90-245 VOLT 50-60 Hz.
XR 8 with electromagnetic ballast operate at 230 VOLT 50-60 Hz
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 6,3 amps at 230V.
Strict adherence to regulatory norms is strongly recommended.
6.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR 8.
A good earth connection is essential for the correct operation of the projector.
7- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.
8
540°
319°
XR 8 SPOT
Electronic ballast
90-245V 50 / 60Hz
Electromagnetic ballast
230 V 50/60 Hz
Ensure that the conductors do not touch each other.Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
The standard configuration of the XR8 is with XLR 5 pins connection.
To convert to an XLR 3 pins configuration proceed as follows:
1) Remove the 2 screws fixing the display cover panel to the unit (photo 1).
2) Remove the screws that fix the XLR connectors to the panel (photo 2).
3) Rotate the electronic card by 180° (photo 3).
4) Place the 3 pins XLR connectors in the special holes and close.
For Installations where long distance DMX cable connections are needed,we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
Photo 2Photo 1 Photo 3
5
3
4 2
1
1=GND
2=DATA-
3=DATA+
CONTROLLER
S T A N D A R D
D M X 512
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
9
XR 8 SPOT
7.1-DMX Addresses
XR8 can be used in two different modes: 16 or 20 DMX (default) channels.
If you want to use the XR8 in 16 channels mode, select the 16 CH mode from the MODE menu and set
the following addresses on the mixer:
Projector 1 A001
Projector 2 A017 If you want to select the next projector, just add “16”
Projector 3 A033
….. A….
projector 6 A081
If you want to use the XR8 in 20 channels mode, select the 20 CH mode from the MODE menu and set
the following addresses:
Projector 1 A001
Projector 2 A021 If you want to select the next projector, just add “20”
Projector 3 A041
….. A….
Projector 6 A101
7.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
10
XR 8 SPOT
DMX IN
DMX OUT
DISPLAY
MAINS
electronic ballast
90-245V ~ 50-60 Hz
electromagnetic ballast
230V ~ 50-60 Hz
8- DISPLAY FUNCTIONS
11
MENU
ENTER
DOWN
UP
DISPLAY FUNCTIONS
The XR8 display panel shows all the available functions . Using these functions, it is possible to
change some of the parameters and add some functions. Changing the DTS setting can vary the
functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
Up-DownMENU ENTERUp-Down
PAN MOVEMENT INVERSION
To reverse Pan movement from left
to right and vice versa
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTERUp-Down
TILT MOVEMENT INVERSION
To reverse Tilt movement from
bottom upwards and vice versa
Up-Down
Counterclockwise
Clockwise
Up-DownMENU ENTER
DMX MODE
To select DMX mode : 20-16
channels
20 CHANNELS
(Pan & Tilt 16 bit)
16 CHANNELS
(Pan & Tilt 16 bit)
Up-Down
Up-Down
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
XR 8 SPOT
Up-Down
MENU
ENTERUp-Down
REVERSE DISPLAY
Reverses display's reading depending on
the mounting position
(On the ground or suspended).
Up-Down
Floor
position
Suspension
position
Up-DownENTER
Up-DownENTER
DISPLAY STAND BY
To turn off the display (after 5 seconds)
Or leave it always on.
Display OFF
Display
always ON
ENTER
ENTER
ENTER
ENTER
MENU ENTER
TEST MODE
Full test and single function test.
Up-Down
12
Up-Down
MENU
ENTER
DEFAULT
To restore default setting
ENTER
Up-Down
MENU ENTER
Fan control
To control the fan speed .
Up-Down
ENTER
Up-Down
(DEFAULT : 12 )
MENU ENTER
Up-Down
ENTER
ENTER
Up-Down
(DEFAULT : 2 )
SPEED control
Pan Tilt Speed control.
8- DISPLAY FUNCTIONS
PAN
TILT
DIMMER
SHUTTER
GOBO SHAKE
GOBO
GOBO ROT.
EFFECTS
EFFECTS ROT.
COLOR
FOCUS
ZOOM
ENTER
XR 8 SPOT
FROST
MENU
ENTER
AUTOMATIC MODE
Automatic game without DMX
controller
ENTER
Up-Down
Up-Down
Up-Down
ENTER
MENU
Up-Down
ENTER
Pcb 8 motors. Pcb PAN&TILT
MENU
Up-Down
ENTER
GOBO Rotation
Gobo Rotation during gobo scrolling
Up-Down
GOBO ROTATION DISABLE
GOBO ROTATION ENABLE
.
ENTER
ENTER
MENU
Up-Down
ENTER
FOCUS
Focus stepper motor settings
Up-Down
FOCUS STEPPER MOTOR TYPE 1
FOCUS STEPPER MOTOR TYPE 2
ENTER
ENTER
ALL
SOFTWARE
Software version
MENU
Up-Down
RESET
Al motors reset
RESET ENABLED VIA DMX
RESET DISABLED VIA DMX
TOTAL RESET
ENTER
ENTER
ENTER
ENTER
Up-Down
MENU
Up-Down
ENTER
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
Up-Down
ENTER
.
Up-Down
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
ENTER
Up-Down
ENTER
Up-Down
.
ENTER
ENTER
ENTER
Up-Down
ENTER
ENTER
ENTER
Up-Down
.
.
ENTER
PAN LOCK
LOCK THE PAN TO THE DESIRED VALUE
TILT LOCK
LOCK THE TILT TO THE DESIRED VALUE
PAN FREE
REMOVE POWER TO PAN MOTOR
TILT FREE
REMOVE POWER TO TILT MOTOR
MENU ENTER
TIMER
lamp life TIME (reset possible)
and total UNIT LIFE TIME (reset not possible)
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ENTER
13
8- DISPLAY FUNCTIONS
XR 8 SPOT
LAMP
Lamp always ON-always OFF
Or lamp ON-OFF selectable via DMX
ENTER
FORCED ON
ENTER
FORCED OFF
ENTER
ON / OFF VIA DMX (default)
MENU
Up-Down
ENTER
Up-Down
ENTER
Up-Down
ADJUST
To adjust the lamp with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and FOCUS
ENTER
ACC
Lamp strikes counter
ENTER
Up-Down
MENU ENTER
REC
Record mode
ENTER
Up-Down
MENU ENTER
Up-Down
Slave
Slave mode as run by GAM.P, Synchronised with master
ENTER
Up-Down
9- AUTOMATIC MODE (auto)
XR8 can work in automatic mode without a DMX controller.
First of all connect the projectors with a DMX cable (picture below).
To activate Auto mode on the first unit, use the menu to run through the different modes until AUTO
appears on the display, at this point press enter.
Now it is possible to select the Game P which is user programmable through REC mode.
To confirm game activation press ENTER.
9.1- Game P
The first unit that will function as a Master must be put in (AUTO) mode, the other projectors have to be
put in slave mode (selectable through the menu). This way all units will be synchronised with the master.
Please note that the projectors must be of the same model.
On the master unit it is possible to vary the speed of the GAME P (SPEE)
NB: It is possible to run GAME P on the other units even though these do not have GAME P programmed.
You can do this by setting the units to the same mode as the master is set before programming GAME P
(16CH DMX) and setting the DMX address to A001.
9.2-Rec Mode
It is possible to program your own game on the XR8 that will then run in AUTO mode (GAME P). Each
unit can have its own programmed game.
In REC mode each projector must be set to the same mode (16CH DMX).
For the programming of GAME P besides the channels necessary to control the unit a further 3 DMX
channels are needed. So that in REC mode if the 16CH mode is selected you will need 19 channels for the
program to work correctly.
Connect the unit to a DMX mixer/controller, every unit should be set to its own Address (See the
paragraph on DMX addresses). The projectors can also be of different models:XR8 Spot/Wash, XR7
Spot/Wash and XR 250 Spot/Wash. When you are in REC mode R.001 appears on the display (DMX
address).
MASTER
ARC 1200
XR 8 SPOT
14
OUT IN
OUT IN
OUT
SLAVE 1 SLAVE 2
The three new DMX channels are:
-Scene channel
-From 0-255 are displayed the programmable scenes (max 16 scenes M.001 M016)
-View channel:
-From 1-19 the unit runs the scene that has been saved in the unit memory and it is possible to
play through the other scenes using the scene channel.
-From 20-235 the unit runs the configuration given by the received input DMX values. With the
channel scene it is possible to pass from one scene to the next,while with REC it is possible to
record the selected scene.
-From 236-255 the unit runs the configuration given by the received DMX values from the
projector in that moment. It is possible to select a scene and then close the GAME P with the REC
channel.
-Recording channel (REC)
Records the set scene with a variation from 0 to 255 (the display flashes indicating that the scene has
been recorded).
You must keep the REC channel set to 0 and to run through the 255 only once you have decided to save
the scene. If GAME P is not closed, by indicating the last scene, in playback mode all 16 scenes will be
played through even if not programmed.
You can set the PAN and TILT motors at high speed on your XR8.
Press menu until you see SPEE.
Press ENTER and select a speed with UP-DOWN (there are 4 speeds). Confirm by pressing ENTER.
When you use speed 4 (the highest) PAN and TILT speed is very high and your projector may loose its
path. In this case, the encoder corrects the position.
Fan speed regulation makes it possible to reduce fan noise. However, the ambient temperature must be
less than 35° C.
12- ERROR MESSAGES:
10- PAN & TILT SPEED (SPEE) (default: 2)
11- FAN SPEED (FANS)( default: 12)
ERROR: COLOR WHEEL POSITION
ERROR: GOBO WHEEL POSITION
ERROR: ZOOM POSITION
ERROR: GOBO ROTATION POSITION
ERROR: INTERNAL
COMMUNICATION
ERROR: AUTO MODE INPUT
ERROR: ENCODER PAN
ERROR: ENCODER TILT
ERROR: DMX ADDRESS
ERROR: LOAD DATA
EEPROM
ERROR: SENSOR CIRCUIT
COLOR/ZOOM
ERROR: SENSOR CIRCUIT
GOBO/GOBO ROTATION
ERROR: SYNCHRONIZED
FREQUENCY MEASURE
(SYNCHRONISM FOR LAMP ON)
ARC 1200
XR 8 SPOT
15
Up-DownENTER
PAN ALIGNMENT
To align pan
ENTER
Up-DownENTER
TILT ALIGNMENT
To align tilt
ENTER
Up-Down
Up-Down
ENTER
Up-DownENTERUp-Down
GOBO WHEEL ALIGNMENT
To align gobo wheel
ENTER
Up-DownENTER
Up-Down
GOBOROTATION ALIGNMENT
To align gobo ROTATION
ENTER
Up-DownENTERUp-Down
FOCUS ALIGNMENT
To align focus
ENTER
Up-DownENTERUp-Down
COLOR WHEEL ALIGNMENT
To align color wheel
ENTER
Up-DownENTERUp-Down
SHUTTER ALIGNMENT
To align shutter
ENTER
Up-DownENTERUp-Down
PRISM ALIGNMENT
To align prism
ENTER
Up-DownENTERUp-Down
LENSES ALIGNMENT
To align Zoom lenses
ES.
ENTER
ARC 1200
XR 8 SPOT
16
13- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XR8 (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
Electronic calibration of the motors.
Reset EEPROM (Reset all settings. ATTENTION: by pressing this key you must
repeat all previous calibrations)
Exit from hidden menu.
16
17
14- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 2).
15- REPLACING GOBOS
XR8 uses a mechanical system which allows the fixture's gobos to be removed without the use of special
tools. Replacement gobos should be made of either heat resistant glass or metal.
An ever-increasing range of gobos is available from your D.T.S. sales network.
Gobo dimensions are as follows:
ø external = 27.9 mm
ø of image with defined edge = 24 mm
thickness = from 0.2 to 4 mm (see catalogue)
Replacing gobos on the rotating gobo wheel
When replacing gobos, ensure that the projector is switched off.
1) Open the projector housing as described above.
2) Remove the gobo holder to allow easier access to the gobo(photo 1 and 2).
3) Release the gobo retaining spring and carefully remove the gobo (photo 3).
4) Reverse the procedure to install a replacement gobo.
Photo 1
Photo 3
Photo 1
Photo 2
XR 8 SPOT
Photo 2
16- PERIODIC CLEANING
16.1- Lenses and reflectors
Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
16.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.
17- PERIODIC CONTROLS
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
Mechanical parts
Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them
if necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors;
refasten them if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR8.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.
Attention
Disconnect mains power prior to removing the projector housing.
18
XR 8 SPOT
16 CHANNELS MODE
1 PAN msb 540°
2 PAN lsb
3 TILT msb 270°
4 TILT lsb
5 SPEED MOVEMENT
6 DIMMER
7 SHUTTER
8 COLOUR
9 COLOUR PROPORTIONAL (Priority in color channel)
10 GOBO
11 GOBO ROTATION
12 PRISM/PRISM ROTATION
13 FOCUS
14 ZOOM
15 FROST (Priority on Zoom channel)
16 LAMP ON-OFF / RESET
18- DMX PROTOCOL
ARC 1200
XR 8 SPOT
19
DMX CHANNEL
1
Parameter: PAN msb
DMX CHANNEL
2
Parameter: PAN lsb
DMX CHANNEL
3
Parameter: TILT msb
DMX CHANNEL
4
Parameter: TILT lsb
DMX CHANNEL
5
Parameter: MOVEMENT SPEED
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
5
Standard
11-25
18
Fast movement
26-127
76
Vector mode from fast to slow
128-247
187
Variable time reaction to
DMX signal ( fast to slow)
248-255
251
Slow reaction time to DMX
signal
DMX CHANNEL
6
Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
-
-
0-8
4
Black-out
9-255
Proportional dimmer
DMX CHANNEL
7
Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9
5
Black-out
10-23
16
StrobE random speed
24-37
30
Strobe speed 1 min.
38-51
44
Strobe speed 2
52-65
58
Strobe speed 3
66-79
72
Strobe speed 4
80-93
86
Strobe speed 5
94-107
100
Strobe speed 6 max.
108-121
114
Pulse open speed 1 min.
122-135
128
Pulse open speed 2
136-149
142
Pulse open speed 3
150-163
156
Pulse open speed 4 max.
164-177
170
Pulse closed speed 1 min.
178-191
184
Pulse closed speed 2
192-205
198
Pulse closed speed 3
206-219
212
Pulse closed speed 4 max.
220-227
225
Colour and Gobo in black-out
228-233
230
Pan and Tilt in black-out
234-255
244
Open
DMX CHANNEL
8
Parameter: COLOUR
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-10
5
Colour1
11-21
16
Bicolour ½
22-32
27
Colour2
33-43
38
Bicolour 2/3
44-54
49
Colour3
55-65
60
Bicolour 3/4
66-76
71
Colour4
77-87
82
Bicolour 4/5
88-98
93
Colour5
99-109
104
Bicolour 5/6
110-120
115
Colour6
121-131
126
Bicolour 6/7
132-142
137
Colour7
143-153
148
Bicolour 7/8
154-164
159
Colour8
ARC 1200
XR 8 SPOT
20
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
