Husqvarna 253 RB Manuale del proprietario

H1153433-10,253RB,GB.fm Page 1 Friday, February 26, 2010 9:55 AM

KEY

T

O SYMBOLS

2

–

English

Symbols

W

ARNING! A clearing saw,

brushcutter or trimmer can be

dangerous if used incorrectly or

carelessly, and can cause serious or

fatal injury to the operator or others.

It is extremely important that you

read and understand the contents of

this operator’s manual.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

• A protective helmet where there

is a risk of falling objects

• Approved hearing protection

• Approved eye protection

Max. speed of output shaft, rpm

This product is in accordance with

applicable EC directives.

Watch out for thrown objects and

ricochets.

The operator of the machine must

ensure, while working, that no

persons or animals come closer than

15 metres.

Machines ﬁtted with saw blades or

grass blades can be thrown violently

to the side when the blade comes

into contact with a ﬁxed object. This is

called blade thrust. The blade is

capable of amputating an arm or leg.

Always keep people and animals at least 15 metres from

the machine.

Arrows which show limits for handle

positioning.

Always wear approved protective

gloves.

Wear sturdy, non-slip boots.

Only use non-metallic, ﬂexible

cutting attachments, i.e. trimmer

heads with trimmer cord.

Noise emission to the environment

according to the European

Community’s Directive. The

machine’s emission is speciﬁed in

chapter Technical data and on label.

Keep all parts of your body away from

hot surfaces.

Other symbols/decals on the mac

hine refer to

special certiﬁcation requirements for certain

markets.

Switch off the engine by moving the

stop switch to the STOP position

before carrying out any checks or

maintenance.

Always wear approved protective

gloves.

Regular cleaning is required.

Visual check.

50FT

15 m

50FT

1

5

m

H1153433-10,253RB,GB.fm Page 2 Friday, February 26, 2010 9:55 AM

CONTENTS

English

–

3

Contents

Note the f

ollowing before

starting:

Please read the oper

ator’s manual carefully.

KEY

TO SYMBOLS

Symbols

................................................................ 2

CONTENTS

Contents

............................................................... 3

Note the following before starting: ........................ 3

INTR

ODUCTION

Dear Customer

, .................................................... 4

WHA

T IS WHAT?

What is what on the br

ush cutter? ........................ 5

GENERAL SAFETY PRECA

UTIONS

Impor

tant .............................................................. 6

Personal protective equipment ............................. 6

Machine

′

s safety equipment ................................. 7

Cutting equipment ................................................ 10

ASSEMBL

Y

Fitting the ﬂ

exible drive shaft ................................ 12

Connecting throttle cable and stop switch wires ... 12

Fitting the J-handle .............................................. 13

Fitting blades and trimmer heads ......................... 13

Fitting the transport guard .................................... 15

Adjusting the harness and brush cutter ................ 15

FUEL HANDLING

Fuel saf

ety ............................................................ 17

Fuel ...................................................................... 17

Fuelling ................................................................. 18

ST

ARTING AND STOPPING

Chec

k before starting ........................................... 19

Starting and stopping ........................................... 19

W

ORKING TECHNIQUES

Gener

al working instructions ................................ 21

MAINTENANCE

Carb

urettor ........................................................... 24

Air ﬁlter ................................................................. 24

Fuel ﬁlter ............................................................... 24

Bevel gear ............................................................ 25

Spark plug ............................................................ 25

Drive shaft ............................................................ 25

Maintenance schedule ......................................... 27

TECHNICAL D

ATA

T

echnical data ...................................................... 28

EC-declaration of conformity ................................ 29

!

W

ARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

W

ARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use genuine

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

!

W

ARNING! A clearing saw, brushcutter

or trimmer can be dangerous if used

incorrectly or carelessly, and can cause

serious or fatal injury to the operator or

others. It is extremely important that you

read and understand the contents of this

operator’s manual.

H1153433-10,253RB,GB.fm Page 3 Friday, February 26, 2010 9:55 AM

4

–

English

INTR

ODUCTION

Dear Customer

,

Cong

ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,

when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production

of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-

powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot of different products,

from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor

driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our

highest priority. The business concept is to develop, manufacture and market motor driven products for forestry and

gardening as well as for building and construction industry. Husqvarna

′

s aim is also to be in the front edge according to

ergonomics, usability, security and environmental protection. That is the reason why we have developed many different

features to provide our products within these areas.

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very

long time to come. The purchase of one of our products gives you access to professional help with repairs and service

whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the

address of your nearest service workshop.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this

operator

′

s manual as a valuable document. By following its

′

content (using, service, maintenance etc) the life span and

the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get

the operator

′

s manual.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

H1153433-10,253RB,GB.fm Page 4 Friday, February 26, 2010 9:55 AM

English

–

5

WHA

T IS

WHA

T?

What is what on the brush cutter?

11

12

18

26

24

25

28

15

14

16

17

10

7

9

8

6

5

3

2

1

4

19

1

20

21

22

14

13

23

27

1

Blade

2 Grease ﬁller cap, bevel gear

3 Bevel gear

4 Cutting attachment guard

5 Shaft

6 J-handle

7 Throttle control

8 Stop switch

9 Throttle lockout

10 Shaft coupling

11 Starter handle

12 Fuel tank

13 Air ﬁlter cover

14 Cylinder cover

15 Spark plug cap and spark plug

16 Air purge

17 Choke control

18 Harness

19 Drive disc

20 Support ﬂange

21 Support cup

22 Locking nut

23 Trimmer head

24 Transport guard

25 Locking pin

26 Socket spanner

27 Screwdriver

28 Operator

′

s manual

H1153433-10,253RB,GB.fm Page 5 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECA

UTIONS

6

–

English

Impor

tant Personal protective equipment

HELMET

A protectiv

e helmet where there is a risk of falling objects

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor

then you must also wear approved protective goggles.

Approved protective goggles must comply with standard

ANSI Z87.1 in the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

IMPORTANT!

The machine is only designed for trimming grass.

The only accessories you can operate with this engine

unit are the cutting attachments we recommend in the

chapter on Technical data.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect

your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading ”Personal protective equipment”.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures

must be carried out by trained and qualiﬁed specialists.

See instructions under the heading Maintenance.

All covers, guards and handles must be ﬁtted before

starting. Ensure that the spark plug cap and ignition

lead are undamaged to avoid the risk of electric shock.

The machine operator must ensure that no people or

animals come closer than 15 metres while working.

When several operators are working in the same area

the safety distance should be at least twice the tree

height and no less than 15 metres.

!

W

ARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

!

W

ARNING! Running an engine in a

conﬁned or badly ventilated area can

result in death due to asphyxiation or

carbon monoxide poisoning.

IMPOR

TANT!

A clearing saw, brushcutter or trimmer can be

dangerous if used incorrectly or carelessly, and can

cause serious or fatal injury to the operator or others. It

is extremely important that you read and understand the

contents of this operator’s manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen.

Ask your dealer for help in choosing the right equipment.

!

W

ARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

H1153433-10,253RB,GB.fm Page 6 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECA

UTIONS

English

–

7

BOO

TS

Wear boots with steel toe-caps and non-slip sole.

CLOTHING

Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always

wear heavy, long pants. Do not wear jewellery, shorts

sandals or go barefoot. Secure hair so it is above shoulder

level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

Mac

hine

′

s safety equipment

This section descr

ibes the machine

′

s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

The life span of the machine can be reduced and the risk

of accidents can increase if machine maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest service workshop.

Thr

ottle lockout

The throttle loc

kout is designed to prevent accidental

operation of the throttle control. When you press the lock

(A) (i.e. when you grasp the handle) it releases the throttle

control (B). When you release the handle the throttle

control and the throttle lockout both move back to their

original positions. This movement is controlled by two

independent return springs. This arrangement means that

the throttle control is automatically locked at the idle

setting.

Make sure the throttle control is locked at the idle setting

when the throttle lockout is released.

Press the throttle lockout and make sure it returns to its

original position when you release it.

Check that the throttle control and throttle lockout move

freely and that the return springs work properly.

See instructions under the heading Start. Start the

machine and apply full throttle. Release the throttle and

check that the cutting attachment stops and remains at a

standstill. If the cutting attachment rotates with the throttle

in the idle position then the carburettor idle setting must

IMPORTANT! All servicing and repair work on the

machine requires special training. This is especially true

of the machine

′

s safety equipment. If your machine fails

any of the checks described below you must contact

your service agent. When you buy any of our products

we guarantee the availability of professional repairs and

service. If the retailer who sells your machine is not a

servicing dealer, ask him for the address of your nearest

service agent.

!

W

ARNING! Never use a machine with

faulty safety equipment. The machine’s

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

H1153433-10,253RB,GB.fm Page 7 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECA

UTIONS

8

–

English

be chec

ked. See instructions under the heading

Maintenance.

Stop s

witch

Use the stop s

witch to switch off the engine.

Start the engine and make sure the engine stops when

you move the stop switch to the stop setting.

Cutting attac

hment guard

This guard is intended to pre

vent loose objects from being

thrown towards the operator. The guard also protects the

operator from accidental contact with the cutting

attachment.

Check that the guard is undamaged and not cracked.

Replace the guard if it has been exposed to impact or is

cracked.

Always use the recommended guard for the cutting

attachment you are using. See chapter on Technical data.

Vibration damping system

Y

our machine is equipped with a vibration damping

system that is designed to minimize vibration and make

operation easier.

Using incorrectly wound cord or a blunt or incorrect

cutting attachment (wrong type or incorrectly ﬁled, see

instructions under the heading Filing the blade) increases

the level of vibration.

The machine

′

s vibration damping system reduces the

transfer of vibration between the engine unit/cutting

equipment and the machine

′

s handle unit.

Regularly check the vibration damping units for cracks or

deformation. Check that the vibration damping element is

undamaged and securely attached.

Mufﬂ

er

The m

ufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user. A mufﬂer

ﬁtted with a catalytic converter is also designed to reduce

harmful exhaust gases.

!

W

ARNING! Never use a cutting

attachment without an approved guard.

See the chapter on Technical data. If an

incorrect or faulty guard is ﬁtted this can

cause serious personal injury.

!

W

ARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. The risk

increases at low temperatures.

H1153433-10,253RB,GB.fm Page 8 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECA

UTIONS

English

–

9

Ne

ver use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to

the machine.

If the mufﬂer on your machine is ﬁtted with a spark

arrestor mesh this must be cleaned regularly. A blocked

mesh will cause the engine to overheat and may lead to

serious damage.

Loc

king nut

A loc

king nut is used to secure some types of cutting

attachment.

When ﬁtting, tighten the nut in the opposite direction to the

direction of rotation of the cutting attachment. To remove

it, undo the nut in the same direction as the cutting

attachment rotates. (CAUTION! The nut has a left-hand

thread.) Tighten the nut using the socket spanner.

The nylon lining inside the locking nut must not be so worn

that you can turn it by hand. The lining should offer a

resistance of at least 1.5 Nm. The nut should be replaced

after it has been put on approx. 10 times.

Harness

Chec

k that the harness is not damaged.

In an emergency situation, release yourself from machine

and harness according to the following method.

!

W

ARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

!

W

ARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

!

W

ARNING! Bear in mind that: The

exhaust fumes from the engine are hot

and may contain sparks which can start

a ﬁre. Never start the machine indoors or

near combustible material!

H1153433-10,253RB,GB.fm Page 9 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECAUTIONS

10 – English

Cutting equipment

This section describes how to choose and maintain your

cutting equipment in order to:

• Reduce the risk of blade thrust.

• Obtain maximum cutting performance.

• Extend the life of cutting equipment.

Cutting equipment

Grass blades and grass cutters are intended for cutting

coarse grass.

A trimmer head is intended for trimming grass.

General rules

Only use cutting attachments with the guards we

recommend! See the chapter on Technical data.

Keep the teeth of the blade correctly sharpened! Follow

our instructions and use the recommended ﬁle gauge. An

incorrectly sharpened or damaged blade increases the

risk of accidents.

Check the cutting attachment for damage or cracks. A

damaged cutting attachment should always be replaced.

Sharpening grass cutters and grass

blades

• See the cutting attachment packaging for correct

sharpening instructions. Sharpen blades and cutters

using a single-cut ﬂat ﬁle.

• Sharpen all edges equally to maintain the balance of

the blade.

IMPORTANT!

Only use cutting attachments with the guards we

recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to

check the correct way to load the cord and the correct

cord diameter.

Keep the teeth of the blade correctly sharpened! Follow

our recommendations. Also refer to the instructions on

the blade packaging.

!

WARNING! Always stop the engine

before doing any work on the cutting

attachment. This continues to rotate even

after the throttle has been released.

Ensure that the cutting attachment has

stopped completely and disconnect the

HT lead from the spark plug before you

start to work on it.

!

WARNING! Using an incorrect cutting

attachment or an incorrectly sharpened

blade increases the risk of blade thrust.

!

WARNING! Always discard a blade that is

bent, twisted, cracked, broken or

damaged in any other way. Never attempt

to straighten a twisted blade so that it

can be reused. Only use original blades

of the speciﬁed type.

H1153433-10,253RB,GB.fm Page 10 Friday, February 26, 2010 9:55 AM

GENERAL SAFETY PRECAUTIONS

English – 11

Trimmer head

• Only use the recommended trimmer heads and

trimmer cords. These have been tested by the

manufacturer to suit a particular engine size. This is

especially important when a fully automatic trimmer

head is used. Only use the recommended cutting

attachment. See the chapter on Technical data.

• Smaller machines generally require small trimmer

heads and vice versa. This is because when clearing

using a cord the engine must throw out the cord

radially from the trimmer head and overcome the

resistance of the grass being cleared.

• The length of the cord is also important. A longer cord

requires greater engine power than a shorter cord of

the same diameter.

• Make sure that the cutter on the trimmer guard is

intact. This is used to cut the cord to the correct length.

• To increase the life of the cord it can be soaked in

water for a couple of days. This will make the line

tougher so that it lasts longer.

IMPORTANT!

Always ensure the trimmer cord is wound tightly and

evenly around the drum, otherwise the machine will

generate harmful vibration.

H1153433-10,253RB,GB.fm Page 11 Friday, February 26, 2010 9:55 AM

ASSEMBLY

12 – English

Fitting the ﬂexible drive shaft

• Loosen two screws at the shaft coupling.

• Slide the ﬂexible shaft through the loops at the

cabling, and ﬁt the ﬂexible shaft to the shaft coupling.

Make sure the shaft engages correctly by turning it

and pushing at the same time.

• Tighten the two screws.

• Install the drive shaft sleeve in the clutch cover so that

the hole is positioned directly underneath the locking

button on the clutch cover.

• Make sure the shaft engages correctly by turning it

and pushing at the same time.

• Make sure the locking pin returns to its original

position, so that the drive shaft sleeve cannot come off

the clutch case.

Connecting throttle cable and

stop switch wires

• Place the throttle wire from the cabling (A) and the

throttle wire from the engine (B) in the plastic sleeve

as shown.

• Close the plastic sleeve.

• Plug the stop switch wires into the matching

connectors from the engine. Note that wire polarity is

not important.

H1153433-10,253RB,GB.fm Page 12 Friday, February 26, 2010 9:55 AM

ASSEMBLY

English – 13

Fitting the J-handle

• Position the handle on the shaft. Note that the handle

must be mounted below the arrow on the shaft.

• Slide the spacer into the slot in the loop handle.

• Fit the nut and screw. Do not overtighten.

• Attach the J-handle to the loop handle using the three

screws, as shown.

• Now adjust the trimmer to give a comfortable working

position. Tighten the bolt/knob.

Fitting blades and trimmer heads

Fitting the guard extension

CAUTION! The guard extension shall always be ﬁtted

when using the trimmer head/plastic blades and

combination guard. The guard extension shall always be

removed when using the grass blade and combination

guard.

Hook the blade guard/combination guard (A) onto the

ﬁtting on the shaft and secure with the bolt.

Enter the guard extension guide in the slot of the

combination guard. Then click the guard extension into

position on the guard with the four quick-fasteners.

!

WARNING! Only grass blades/grass

cutters or trimmer heads/plastic blades

may be used when the J-handle is ﬁtted.

Saw blades must never be used with the

J-handle.

!

WARNING!

When ﬁtting the cutting attachment it is

extremely important that the raised

section on the drive disc/support ﬂange

engages correctly in the centre hole of

the cutting attachment. If the cutting

attachment is ﬁtted incorrectly it can

result in serious and/or fatal personal

injury.

!

WARNING! Never use a cutting

attachment without an approved guard.

See the chapter on Technical data. If an

incorrect or faulty guard is ﬁtted this can

cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be

used the machine must be equipped with the correct

handlebar, blade guard and harness.

H1153433-10,253RB,GB.fm Page 13 Friday, February 26, 2010 9:55 AM

ASSEMBLY

14 – English

The guard extension is removed easily using a

screwdriver, see illustration.

Fitting a blade guard, grass blade and

grass cutter

• Hook the blade guard/combination guard (A) onto the

ﬁtting on the shaft and secure with the bolt (L). Use the

recommended blade guard. See the Technical data

section. CAUTION! Ensure that the guard extension is

removed.

• Fit the drive disc (B) on the output shaft.

• Turn the blade shaft until one of the holes in the drive

disc aligns with the corresponding hole in the gear

housing.

• Insert the locking pin (C) in the hole to lock the shaft.

• Place the blade (D), support cup (E) and support

ﬂange (F) on the output shaft.

• Fit the nut (G). The nut must be tightened to a torque

of 35-50 Nm (3.5-5 kpm). Use the socket spanner in

the tool kit. Hold the shaft of the spanner as close to

the blade guard as possible. To tighten the nut, turn

the spanner in the opposite direction to the direction

of rotation (Caution! left-hand thread).

Fitting the trimmer guard and trimmer

head

• Fit the correct trimmer guard (A) for use with the

trimmer head. CAUTION! Ensure that the guard

extension is ﬁtted.

• Hook the trimmer guard/combination guard onto the

ﬁtting on the shaft and secure with the bolt (L).

• Fit the drive disc (B) on the output shaft.

• Turn the blade shaft until one of the holes in the drive

disc aligns with the corresponding hole in the gear

housing.

• Insert the locking pin (C) in the hole to lock the shaft.

• Screw on the trimmer head/plastic blades (H) in the

opposite direction to the direction of rotation.

• To dismantle, follow the instructions in the reverse

order.

A

L

G

E

D

F

B

C

B

A

M

L

H

A

L

C

M

H

H1153433-10,253RB,GB.fm Page 14 Friday, February 26, 2010 9:55 AM

ASSEMBLY

English – 15

Fitting the transport guard

• Insert the blade in the transport guard (A).

• Snap the two fasteners (B) into the slots (C) to secure

the transport guard.

Adjusting the harness and brush

cutter

Adjusting the backplate height

• Loosen the two fasteners holding the backplate.

• Loosen the backplate from the frame on one side.

• Move the backplate to the desired height and fasten it.

Make sure the pin aligns with one of the holes on the

frame, see picture.

Adjusting the harness

• Put on the harness.

• Tighten the waist strap so that it sits securely.

H1153433-10,253RB,GB.fm Page 15 Friday, February 26, 2010 9:55 AM

ASSEMBLY

16 – English

• Tighten the chest strap.

• Adjust the chest strap vertically if needed and make

sure it ﬁts well.

• Adjust the shoulder straps to distribute the load evenly

across your shoulders.

• Loosen or tighten the waist strap so that approx. 70%

of the load is on your waist and 30% on your

shoulders.

H1153433-10,253RB,GB.fm Page 16 Friday, February 26, 2010 9:55 AM

FUEL HANDLING

English – 17

Fuel safety

Never start the machine:

1 If you have spilt fuel on it. Wipe off the spillage and

allow remaining fuel to evaporate.

2 If you have spilt fuel on yourself or your clothes,

change your clothes. Wash any part of your body that

has come in contact with fuel. Use soap and water.

3 If the machine is leaking fuel. Check regularly for

leaks from the fuel cap and fuel lines.

Transport and storage

• Store and transport the machine and fuel so that there

is no risk of any leakage or fumes coming into contact

with sparks or naked ﬂames, for example, from

electrical machinery, electric motors, electrical relays/

switches or boilers.

• When storing and transporting fuel always use

approved containers intended for this purpose.

• When storing the machine for long periods the fuel

tank must be emptied. Contact your local petrol

station to ﬁnd out where to dispose of excess fuel.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• The transport guard must always be ﬁtted to the

cutting attachment when the machine is being

transported or in storage.

• Secure the machine during transport.

Fuel

CAUTION! The machine is equipped with a two-stroke

engine and must always been run using a mixture of

petrol and two-stroke oil. It is important to accurately

measure the amount of oil to be mixed to ensure that the

correct mixture is obtained. When mixing small amounts

of fuel, even small inaccuracies can drastically affect the

ratio of the mixture.

Petrol

CAUTION! Always use a quality petrol/oil mixture at least

90 octane (RON). If your machine is equipped with a

catalytic converter (see chapter on Technical data) always

use a good quality unleaded petrol/oil mixture. Leaded

petrol will destroy the catalytic converter.

Use low-emission petrol, also known as alkylate petrol, if

it is available.

• The lowest octane recommended is 90 (RON). If you

run the engine on a lower octane grade than 90 so-

called knocking can occur. This gives rise to a high

engine temperature, which can result in serious

engine damage.

• When working at continuous high revs a higher octane

rating is recommended.

Two-stroke oil

• For best results and performance use HUSQVARNA

two-stroke engine oil, which is specially formulated for

our air-cooled two-stroke engines.

• Never use two-stroke oil intended for water-cooled

engines, sometimes referred to as outboard oil (rated

TCW).

• Never use oil intended for four-stroke engines.

• A poor oil quality and/or too high oil/fuel ratio may

jeopardise function and decrease the life time of

catalytic converters.

• Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB

formulated for air-cooled, two-stroke engines.

!

WARNING! Take care when handling fuel.

Bear in mind the risk of ﬁre, explosion

and inhaling fumes.

!

WARNING! Fuel and fuel fumes are

highly inﬂammable and can cause

serious injury when inhaled or allowed to

come in contact with the skin. For this

reason observe caution when handling

fuel and make sure there is adequate

ventilation.

Petrol, litre

Two-stroke oil, litre

2% (1:50) 3% (1:33)

5 0,10 0,15

10 0,20 0,30

15 0,30 0,45

20 0,40 0,60

H1153433-10,253RB,GB.fm Page 17 Friday, February 26, 2010 9:55 AM

FUEL HANDLING

18 – English

Mixing

• Always mix the petrol and oil in a clean container

intended for fuel.

• Always start by ﬁlling half the amount of the petrol to

be used. Then add the entire amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount of

petrol.

• Mix (shake) the fuel mixture thoroughly before ﬁlling

the machine’s fuel tank.

• Do not mix more than one month’s supply of fuel at a

time.

• If the machine is not used for some time the fuel tank

should be emptied and cleaned.

Fuelling

• Always use a fuel container with an anti-spill valve.

• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Ensure that the fuel is well mixed by shaking the

container before ﬁlling the tank.

!

WARNING! The catalytic converter

mufﬂer gets very hot during and after

use. This also applies during idling. Be

aware of the ﬁre hazard, especially when

working near ﬂammable substances and/

or vapours.

!

WARNING! Taking the following

precautions, will lessen the risk of ﬁre:

Do not smoke or place hot objects near

fuel.

Always shut off the engine before

refuelling.

Always stop the engine and let it cool for

a few minutes before refuelling.

When refuelling, open the fuel cap slowly

so that any excess pressure is released

gently.

Tighten the fuel cap carefully after

refuelling.

Always move the machine away from the

refuelling area before starting.

H1153433-10,253RB,GB.fm Page 18 Friday, February 26, 2010 9:55 AM

STARTING AND STOPPING

English – 19

Check before starting

• Never use the machine without a guard nor with a

defective guard.

• All covers must be correctly ﬁtted and undamaged

before you start the machine.

• Check the blade to ensure that no cracks have formed

at the bottom of the teeth or by the centre hole. The

most common reason why cracks are formed is that

sharp corners have been formed at the bottom of the

teeth while sharpening or that the blade has been

used with dull teeth. Discard a blade if cracks are

found.

• Check that the support ﬂange is not cracked due to

fatigue or due to being tightened too much. Discard

the support ﬂange if it is cracked.

• Ensure the locking nut has not lost its captive force.

The nut lock should have a locking force of at least 1.5

Nm. The tightening torque of the locking nut should be

35-50 Nm.

• Check that the blade guard is not damaged or

cracked. Replace the blade guard if it is exposed to

impact or is cracked.

• Check that the trimmer head and trimmer guard are

not damaged or cracked. Replace the trimmer head or

trimmer guard if they have been exposed to impact or

are cracked.

Starting and stopping

Starting

Ignition: Set the stop switch to the start position.

Primer bulb: Press the air purge repeatedly until fuel

begins to ﬁll the bulb. The bulb need not be completely

ﬁlled.

!

WARNING! The complete clutch cover

and shaft must be ﬁtted before the

machine is started, otherwise the clutch

can come loose and cause personal

injury.

Always move the machine away from the

refuelling area before starting. Place the

machine on a ﬂat surface. Ensure the

cutting attachment cannot come into

contact with any object.

Make sure no unauthorised persons are

in the working area, otherwise there is a

risk of serious personal injury. The safety

distance is 15 metres.

H1153433-10,253RB,GB.fm Page 19 Friday, February 26, 2010 9:55 AM

STARTING AND STOPPING

20 – English

Choke: Set the choke control in the choke position.

Hold the body of the machine on the ground using your

left hand (CAUTION! Not with your foot!). Grip the starter

handle, slowly pull out the cord with your right hand until

you feel some resistance (the starter pawls grip), now

quickly and powerfully pull the cord.

Never twist the

starter cord around your hand.

Repeat pulling the cord until the engine starts. When the

engine starts. return choke control to run position and

apply full throttle; the throttle will automatically disengage

from the start setting.

CAUTION! Do not pull the starter cord all the way out and

do not let go of the starter handle when the cord is fully

extended. This can damage the machine.

CAUTION! Do not put any part of your body in marked

area. Contact can result in burns to the skin, or electrical

shock if the spark plug cap has been damaged. Always

use gloves. Do not use a machine with damaged spark

plug cap.

Stopping

Stop the engine by switching off the ignition.

!

WARNING! When the engine is started

with the choke in either the choke or

start throttle positions the cutting

attachment will start to rotate

immediately.

H1153433-10,253RB,GB.fm Page 20 Friday, February 26, 2010 9:55 AM

La pagina sta caricando ...

Husqvarna 253 RB Manuale del proprietario

Husqvarna 253 RB Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti