Kenwood TH-F6A Manuale utente

Marca: Kenwood

Modello: TH-F6A

Categoria: Radio a due vie

Tipo: Manuale utente

Questo manuale è adatto anche per

TH-F7E

09 08 07 06 05 04 03 02 01 00

144/ 220/ 440 MHz FM TRIBANDER

TH-F6A

144/ 430 MHz FM DUAL BANDER

TH-F7E

INSTRUCTION MANUAL

KENWOOD CORPORATION

FM TRIBANDER TH-F6

MODELS COVERED BY THIS MANUAL

The models listed below are covered by this manual.

TH-F6A: 144/ 220/ 440 MHz FM Tri-band

Portable Transceiver

TH-F7E: 144/ 430 MHz FM Dual-band

Portable Transceiver

MARKET CODES

K-type: The Americas

E-type: Europe/ General

T-type: The United Kingdom

The market code is shown on the carton box.

Refer to the specifications {pages 53, 54} for the

information on available operating frequencies within

each model.

NOTICE TO THE USER

One or more of the following statements may be

applicable for this equipment.

FCC WARNING

This equipment generates or uses radio frequency energy.

Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in

the instruction manual. The user could lose the authority to

operate this equipment if an unauthorized change or

modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED

BY THE FCC

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation.

This equipment generates, uses and can generate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the dealer for technical assistance.

PRECAUTIONS

Please observe the following precautions to prevent

fire, personal injury, or transceiver damage:

• Do not transmit with high output power for

extended periods. The transceiver may overheat.

• Do not modify this transceiver unless instructed by

this manual or by KENWOOD documentation.

• When using a regulated power supply, connect the

specified DC cable (option) to the DC IN jack on

the transceiver. The supply voltage must be

between 12 V and 16 V to prevent damaging the

transceiver.

• When connecting the transceiver to a cigarette

lighter socket in a vehicle, use the specified

cigarette lighter cable (option).

• Do not expose the transceiver to long periods of

direct sunlight nor place the transceiver close to

heating appliances.

• Do not place the transceiver in excessively dusty

areas, humid areas, wet areas, nor on unstable

surfaces.

• If an abnormal odor or smoke is detected coming

from the transceiver, turn OFF the power

immediately and remove the battery case or the

battery pack from the transceiver. Contact your

authorized KENWOOD dealer, customer service,

or service station.

THANK YOU

Thank you for choosing this KENWOOD TH-F6A/

TH-F7E transceiver. It has been developed by a

team of engineers determined to continue the

tradition of excellence and innovation in KENWOOD

transceivers.

First, don’t let the size fool you. This small FM

portable transceiver features 2 m, 1.25 m (TH-F6A

only), and 70 cm amateur radio band operation plus

another all-mode 100 kHz to 1.3 GHz receiver (SSB

and CW are up to 470 MHz). In the meantime, as

you learn how to use this transceiver, you will also

find that KENWOOD is pursuing “user friendliness”.

For example, each time you change the Menu No. in

Menu mode, you will see a text message on the

display that lets you know what you are configuring.

Though user friendly, this transceiver is technically

sophisticated and some features may be new to you.

Consider this manual to be a personal tutorial from

the designers. Allow the manual to guide you through

the learning process now, then act as a reference in

the coming years.

FEATURES

• Ultra compact design

• 2 m, 1.25 m (TH-F6A only), and 70 cm amateur

radio band FM transceiver operation

• A separate wide band, all-mode receiver, built-in

• Dual-frequency receive within the same amateur

radio bands

• 400 memory channels plus 34 special function

memory channels (35 channels for TH-F6A)

• Long operation period with a Li-ion battery pack

• High output power (up to 5 W operation)

• Easy to control and select various functions with

Multi-scroll key

• 9600 bps Packet-ready data (Speaker/ Mic.) jack

• Built-in VOX function

• Meets MIL-STD 810C/ D/ E, Rain, Humidity,

Vibration, and Shock

SUPPLIED ACCESSORIES

After carefully unpacking the transceiver, identify the

items listed in the table below. We recommend you

keep the box and packing material in case you need

to repack the transceiver in the future.

yrosseccA rebmuNtraP

ytitnauQ

A6F-HT E7F-HT

)K( )E( )T(

koohtleBXX-3260-92J111

annetnA

XX-1870-09T1––

XX-9870-09T–11

partSXX-2430-96J111

retliFeniLXX-7141-97L–11

yrettabnoi-iLXX-9790-90W111

regrahC

XX-7290-80W1––

XX-8290-80W–1–

XX-9290-80W––1

noitcurtsnI

launaM

XX-1441-26B

)S/E(

111

XX-2441-26B

)I/F(

–1–

XX-3441-26B

)G/D(

–1–

ecitoNETT&RXX-7622-95B–11

dracytnarraW—111

WRITING CONVENTIONS FOLLOWED

The writing conventions described below have

been followed to simplify instructions and avoid

unnecessary repetition.

noitcurtsnI oDottahW

sserP ]YEK[ .esaelerdnasserP YEK .

sserP

]1YEK[ , ]2YEK[ .

sserP 1YEK esaeler,yliratnemom

1YEK sserpneht, 2YEK .

sserP

]YEK[)s1( .

dlohdnasserP YEK arofnwod

.dnoces

sserP

]2YEK[+]1YEK[ .

dlohdnasserP 1YEK neht,nwod

sserp 2YEK eromeraerehtfI.

dlohdnasserp,syekowtnaht

ehtlitnunrutniyekhcaenwod

.desserpneebsahyeklanif

sserP

][+]YEK[ .

sserp,FFOreviecsnartehthtiW

dlohdna YEK NOhctiwsneht,

gnisserpybrewopreviecsnarteht

][ .)REWOP(

Since the amateur radio bands are slightly different

from country to country, the following meter band

descriptions are used in this manual.

• 2 m band : 144 ~ 148 MHz or 144 ~ 146 MHz

• 1.25 m band: 222 ~ 225 MHz

• 70 cm band : 420 ~ 450 MHz or 430 ~ 440 MHz

CONTENTS

TONE FREQ. ID SCAN ......................................... 14

CHAPTER 6 MEMORY CHANNELS

SIMPLEX & REPEATER OR ODD-SPLIT MEMORY

CHANNEL? ........................................................... 15

STORING SIMPLEX FREQUENCIES OR

STANDARD REPEATER FREQUENCIES.........15

STORING ODD-SPLIT REPEATER

FREQUENCIES................................................. 15

RECALLING A MEMORY CHANNEL................. 16

Using the Tuning Control or / keys ...........16

Using a Numeric Keypad .............................. 16

CLEARING A MEMORY CHANNEL ...................16

MEMORY RECALL MODE ................................ 16

NAMING A MEMORY CHANNEL........................... 17

MEMORY CHANNEL GROUPS ............................18

RECALLING A MEMORY CHANNEL USING

MEMORY GROUP FUNCTION ......................... 18

ERASING MEMORY CHANNELS USING

MEMORY GROUP DELETE FUNCTION........... 18

MEMORY CHANNEL TRANSFER ......................... 18

MEMORY \ VFO TRANSFER..........................18

CHANNEL \ CHANNEL TRANSFER ............... 18

CALL CHANNEL.................................................... 19

RECALLING THE CALL CHANNEL...................19

REPROGRAMMING THE CALL CHANNEL ......19

INFORMATION CHANNELS..................................20

RECALLING AN INFORMATION CHANNEL ..... 20

REPROGRAMMING THE INFORMATION

CHANNEL .........................................................20

CHANNEL DISPLAY..............................................21

CHAPTER 7 SCAN

NORMAL SCAN ....................................................22

BAND SCAN ..................................................... 22

PROGRAM SCAN .............................................23

Storing Program Scan Frequency Range......23

Performing the Program Scan....................... 23

MHz SCAN ........................................................23

MEMORY SCAN .................................................... 24

ALL-CHANNEL SCAN ....................................... 24

GROUP SCAN ..................................................24

Memory Group Link ...................................... 24

CALL SCAN ........................................................... 25

PRIORITY SCAN .................................................... 25

PROGRAMMING PRIORITY CHANNELS ......... 25

USING PRIORITY SCAN................................... 25

INFORMATION CHANNEL SCAN ........................... 26

VISUAL SCAN ........................................................ 26

USING VISUAL SCAN (VFO) ............................ 26

USING VISUAL SCAN

(MEMORY CHANNEL) ...................................... 27

MEMORY CHANNEL LOCKOUT........................... 27

SCAN RESUME METHOD ....................................27

CHAPTER 8 SELECTIVE CALL

CTCSS and DCS ................................................... 28

CTCSS .................................................................. 28

USING CTCSS ..................................................28

MODELS COVERED BY THIS MANUAL

MARKET CODES

NOTICE TO USER

PRECAUTIONS

THANK YOU............................................................. i

FEATURES............................................................... i

SUPPLIED ACCESSORIES ..................................... i

WRITING CONVENTIONS FOLLOWED .................. i

CONTENTS............................................................. ii

CHAPTER 1 PREPARATION

INSTALLING THE Li-ion BATTERY PACK ............... 1

INSTALLING ALKALINE BATTERIES ......................1

INSTALLING THE ANTENNA .................................. 1

ATTACHING THE HAND STRAP............................. 1

INSTALLING THE BELT CLIP.................................. 1

CHARGING THE Li-ion BATTERY PACK.................2

CONNECTING TO A CIGARETTE LIGHTER

SOCKET..................................................................2

CONNECTING TO A REGULATED

POWER SUPPLY ....................................................2

CHAPTER 2 YOUR FIRST QSO

FIRST QSO .............................................................3

CHAPTER 3 GETTING ACQUAINTED

KEYS AND CONTROLS ..........................................4

DISPLAY .................................................................5

BASIC OPERATION

SWITCHING POWER ON/ OFF ..........................6

ADJUSTING VOLUME ........................................ 6

ADJUSTING SQUELCH ......................................6

SELECTING A BAND .......................................... 6

MULTI-SCROLL KEY...........................................6

TRANSMITTING..................................................7

Selecting Output Power .................................. 7

SELECTING A FREQUENCY .............................. 7

VFO mode ......................................................7

MHz mode ......................................................7

Direct Frequency Entry ................................... 7

CHAPTER 4 MENU SETUP

WHAT IS A MENU?..................................................9

MENU ACCESS ......................................................9

SELECTING A MENU LANGUAGE ......................... 9

MENU FUNCTION LIST .......................................... 9

ALPHABETICAL FUNCTION LIST......................... 11

CHAPTER 5 OPERATING THROUGH REPEATERS

OFFSET PROGRAMMING FLOW......................... 12

PROGRAMMING OFFSET................................ 12

Selecting Offset Direction.............................. 12

Selecting Offset Frequency ........................... 12

Activating Tone Function ............................... 13

Selecting a Tone Frequency.......................... 13

AUTOMATIC REPEATER OFFSET ....................... 13

REVERSE FUNCTION .......................................... 14

AUTOMATIC SIMPLEX CHECK (ASC).................. 14

iii

VOX.......................................................................41

VOX GAIN .........................................................41

VOX DELAY TIME .............................................41

VOX ON BUSY.................................................. 42

CHAPTER 12 WIRELESS REMOTE CONTROL

PREPARATION ..................................................... 43

CONTROL OPERATION........................................43

CHAPTER 13 OPTIONAL ACCESSORIES

OPTIONAL ACCESSORIES .................................. 44

CHAPTER 14 INTERFACING TO PERIPHERALS

SP/MIC JACK ........................................................45

SELECTING SP/MIC JACK FUNCTION ............45

SP/MIC......................................................... 45

TNC..............................................................45

PC................................................................46

CHAPTER 15 TROUBLESHOOTING

GENERAL INFORMATION .................................... 47

SERVICE...........................................................47

SERVICE NOTE ................................................47

CLEANING ........................................................47

BACKUP BATTERY............................................... 47

TROUBLESHOOTING........................................... 48

MICROPROCESSOR RESET ............................... 50

INITIAL SETTINGS............................................ 50

VFO RESET ......................................................50

MENU RESET ...................................................50

FULL RESET .....................................................50

PERFORMING RESET ..................................... 50

OPERATION NOTICES ......................................... 51

OPERATING VOLTAGE ....................................51

TUNING IN SSB/ CW MODE............................. 51

RECEIVING IN AM BAND ................................. 51

RECEIVING SIGNALS IN CITIES......................51

BEAT AND NOISE ............................................. 51

TRANSMISSION ............................................... 51

INTERNAL BEATS ............................................51

Internal Beats Frequency Formula ................ 52

CHAPTER 16 SPECIFICATIONS

SPECIFICATIONS ................................................. 53

CHAPTER 17 APPENDIX

TV CHANNELS (VHF) ...........................................55

TV CHANNELS (UHF) ...........................................56

MARINE CHANNELS (VHF) ..................................57

CITIZEN BAND CHANNELS..................................57

CHAPTER 18 INDEX

INDEX ................................................................... 58

SELECTING A CTCSS FREQUENCY ............... 28

CTCSS FREQ. ID SCAN ................................... 29

DCS.......................................................................29

USING DCS ...................................................... 29

SELECTING A DCS CODE................................ 29

DCS CODE ID SCAN ........................................ 30

CHAPTER 9 DTMF FUNCTIONS

MANUAL DIALING.................................................31

DTMF TX HOLD ................................................31

AUTOMATIC DIALER ............................................31

STORING A DTMF NUMBER IN MEMORY .......31

TRANSMITTING A STORED DTMF

NUMBER...........................................................32

ADJUSTING THE DTMF TONE

TRANSMISSION SPEED .................................. 32

ADJUSTING THE PAUSE DURATION .............. 32

DTMF LOCK.......................................................... 32

CHAPTER 10 UTILIZING THE B-BAND

ABOUT THE B-BAND ............................................ 33

B-BAND FREQUENCY...................................... 33

B-band Frequency Coverage (TH-F6A) ........ 33

B-band Frequency Coverage (TH-F7E) ........ 34

SELECTING A MODE FOR THE B-BAND ............. 34

LSB/ USB/ CW/ AM/ FM/ WFM .......................... 34

BAR ANTENNA ..................................................... 34

FINE TUNING........................................................ 35

ACTIVATING FINE TUNING ..............................35

Selecting a Fine Tuning Frequency Step.......35

CHAPTER 11 OPERATOR CONVENIENCES

APO (Auto Power OFF) ......................................... 36

ATTENUATOR.......................................................36

BATTERY LIFE......................................................36

BATTERY REMAINING ......................................... 36

BATTERY TYPE ................................................ 36

BATTERY SAVER.................................................. 37

BEAT SHIFT .......................................................... 37

BEEP FUNCTION.................................................. 37

DISPLAY CONTRAST ........................................... 37

FREQUENCY STEP SIZE ..................................... 37

LAMP .................................................................... 38

LOCK FUNCTION ................................................. 38

TUNE ENABLE..................................................38

MICROPHONE PF KEYS (OPTIONAL) .................38

MONITOR ............................................................. 39

NARROW BAND FM OPERATION........................39

POWER-ON MESSAGE ........................................ 39

PROGRAMMABLE VFO........................................ 39

SINGLE BAND OPERATION .................................40

TIME-OUT TIMER ................................................. 40

TONE ALERT ........................................................ 40

TX INHIBIT ............................................................ 40

TX POWER ........................................................... 41

VOLUME BALANCE.............................................. 41

PREPARATION

INSTALLING THE Li-ion BATTERY PACK

Note: Because the battery pack is provided uncharged, you must

charge the battery pack before using it with the transceiver. To

charge the battery pack, refer to “CHARGING THE Li-ion BATTERY

PACK” {page 2}.

1 Position the two grooves on the edge and two

hooks at the bottom of the battery pack over the

corresponding guides on the back of the

transceiver.

2 Slide the battery pack along the back of the

transceiver until the release latch on the top of the

transceiver locks the battery pack in place.

3 To remove the battery pack, push the release latch

on top, then slide the battery pack down.

INSTALLING ALKALINE BATTERIES

1 To open the battery case (BT-13), push the locking

tab in, then pull the cover back.

2 Insert (or remove) four AA (LR6) alkaline batteries.

• Be sure to match the battery polarities with

those marked in the bottom of the battery case.

3 Align the two tabs on the battery case cover, then

close the cover until the locking tabs click.

4 To install the battery case onto (or remove it from)

the transceiver, follow steps 1 to 3 of

“INSTALLING THE Li-ion BATTERY PACK”

{above}.

Note: When you use the alkaline batteries, access Menu No. 30

(BATTERY), then select “ALKALINE”. Otherwise, the battery

remaining cannot be measured correctly {page 36}.

INSTALLING THE ANTENNA

Hold the base of the supplied antenna, then screw

the antenna into the connector on the top panel of the

transceiver until secure.

ATTACHING THE HAND STRAP

If desired, you can attach the supplied hand strap to

the transceiver.

INSTALLING THE BELT CLIP

You can install the supplied belt clip to the transceiver

tightening the 2 supplied screws.

Tab

Screws

Strap

Tabs

Grooves

Latch

1 PREPARATION

CHARGING THE Li-ion BATTERY PACK

The Li-ion battery pack can be charged after it has

been installed onto the transceiver. The battery pack

is provided uncharged for safety purposes.

1 Confirm that the transceiver power is OFF.

• While charging the battery pack, leave the

transceiver power OFF.

2 Insert the charger plug into the DC IN jack of the

transceiver.

3 Plug the charger into an AC wall outlet.

• Charging starts and 2 LEDs on the top panel

lights orange.

4 It takes approximately 6.5 hours to charge an

empty PB-42L Li-ion battery pack. When charging

completes, the LEDs unlight; remove the charger

plug from the transceiver DC IN jack.

5 Unplug the charger from the AC wall outlet.

Note:

◆

If you turn the transceiver ON and press [F], [LOW/ BATT] while

charging the battery pack, “CHARGING” appears. “STANDBY”

appears when the charging completes.

◆

The transceiver becomes warm while charging the battery pack.

◆

If the charger plug is plugged into the DC IN jack before the

battery pack is attached, turn the transceiver ON and then OFF

again to initiate the charging.

◆

Exceeding the specified charge period shortens the useful

life of the Li-ion battery pack.

◆

The provided charger is designed to charge only the

provided PB-42L Li-ion battery pack. Charging other models

of battery packs may damage the charger and battery pack.

◆

Do not press [PTT] while charging.

◆

The battery pack must be kept in cool and dry place.

◆

Never leave the battery pack in the direct sun light.

CONNECTING TO A CIGARETTE LIGHTER

SOCKET

To connect the transceiver to the cigarette lighter

socket in your vehicle, use an optional PG-3J

Cigarette Lighter cable.

While the PG-3J is connected to the cigarette lighter

plug, the transceiver automatically start charging the

Li-ion battery pack (PB-42L). When you operate the

transceiver, it charges the Li-ion battery pack in back

ground. If the transceiver is turned OFF, the 2 LEDs

light orange while charging. When the charging

completes, they turn OFF {above}.

To connect with an external 24 V power source via a DC-DC

converter, only use the optional PG-3J Cigarette Lighter cable.

Using the PG-2W DC cable in this situation may cause a fire.

PG-2W

24V

12V

24V

PG-3J

12V

24V

PG-3J

Note: If the input voltage exceeds approximately 16.5 V, warning

beeps sound and “VOLTAGE ERROR” appears.

CONNECTING TO A REGULATED POWER

SUPPLY

To connect the transceiver to an appropriate

regulated power supply, use an optional PG-2W

DC cable.

1 Confirm that the power of both the transceiver and

the power supply are OFF.

2 Connect the optional PG-2W DC cable to the

power supply; the red lead to the positive (+)

terminal, and the black lead to the negative (–)

terminal.

3 Connect the barrel plug on the DC cable to

the DC IN jack of the transceiver.

If the transceiver is turned OFF while a regulated

power supply is connected with the DC IN jack, it

automatically initiates charging the Li-ion battery pack

(PB-42L) {above}.

Note:

◆

If the DC power supply voltage is below 12.0 V DC, you may not

be able to charge the Li-ion battery pack (PB-42L).

◆

The supply voltage must be between 12.0 V and 16.0 V to

prevent damaging the transceiver. If input voltage exceeds

approximately 16.5 V, warning beeps sound and “VOLTAGE

ERROR” appears. Remove the DC IN jack plug immediately.

◆

If the DC power supply voltage is above 14.5 V DC and “H” (High

Power) is selected, “H” icon blinks and the output power is

reduced to “L” level (Low Power) automatically {page 41}.

DC IN jack

DC 12 V

DC-DC Converter

Fuses (4 A)

DC IN jack

Socket

YOUR FIRST QSO

FIRST QSO

Are you ready to give your transceiver a quick try?

Reading this page should get your voice on the air

right away. The instructions below are intended only

for a quick guide. If you encounter problems or there

is something you would like to know more, read the

detailed explanations given later in this manual.

FM TRIBANDER TH-F6

q Press and hold [ ] (POWER) briefly to switch

the transceiver power ON.

• A high pitched double beep sounds and then

“KENWOOD” and “HELLO !!” appear

momentarily. The various indicators and 2

frequencies appear on the LCD.

• The transceiver stores the parameters when it

is turned OFF. It automatically recalls these

parameters next time you turn the transceiver

ON again.

w Press [A/B] to select the frequency band on top.

• Each time you press [A/B], the “s” icon

moves, indicating which frequency band is

currently selected for operation.

e Turn the VOL control clockwise to the 11 o’clock

position.

r Press [BAND] until you select the amateur radio

band you wish to operate.

t Turn the Tuning control to select the receive

frequency.

• You may further turn the VOL control to adjust

the volume level of the signal.

y To transmit, hold the transceiver approximately

5 cm (2 inches) from your mouth.

u Press and hold the PTT switch, then speak in your

normal tone of voice.

i Release the PTT switch to receive.

o Repeat steps y, u and i to continue

communication.

GETTING ACQUAINTED

KEYS AND CONTROLS

FM TRIBANDER TH-F6

A/ B-band status LEDs

Green : Busy

Red : Transmitting

Orange: Charging

Tuning Control

VOL Control

Display

PTT switch

LAMP Key

Antenna

Speaker/ Mic.

Keypad

Power Switch

MONI Key

Multi-scroll

Key

SP/MIC jack

DC IN jack

Battery release

3 GETTING ACQUAINTED

q EL

Appears when the transmit output power is set to Low

(“L”) or Economic Low (“EL”) {pages 7, 41}.

w H

Appears when the transmit output power is set to

High (“H”) {pages 7, 41}.

e LSB

Appears when lower side band (LSB) is selected for

B-band {page 34}.

r USB

Appears when upper side band (USB) is selected for

B-band {page 34}.

t CW

Appears when CW is selected for B-band {page 34}.

y WFMN

“WFM” appears when wide FM mode is selected

{page 34}. “FM” appears when normal FM mode is

selected. “FMN” appears when narrow FM mode is

selected {page 39}.

u AM

“AM” appears when AM mode is selected {page 34}.

Appears when a Priority Scan is activated {page 25}.

o FINE

Appears when a Fine Tuning function is activated

{page 35}.

!0 VOX

Appears when the VOX function is activated

{page 41}.

Appears when the Automatic Simplex Check (ASC) is

activated {page 14}.

Appears when the Lock function is ON {page 38}.

Appears when the function key is pressed.

S-meter (RX) and relative RF power meter (TX).

!5 CT

“CT” appears when the CTCSS function is activated

{page 28}.

Appears when the Tone function is activated

{page 13}.

!7 DCS

Appears when the DCS function is activated

{page 29}.

!8 +/ –/

Appears when the repeater shift function is activated

{page 12}.

!9 R

Appears when the Reverse function is activated

{page 14}.

Appears when the Tone Alert function is activated

{page 40}.

Appears when the displayed memory channel has

been locked out {page 27}.

@2 Dot-matrix display

76 x 16 dot-matrix display. It displays various

information, such as the operating frequencies, menu

settings, and etc.

DISPLAY

2 3 4 5 6 7 8 9 10 11 12 13

3 GETTING ACQUAINTED

BASIC OPERATION

SWITCHING POWER ON/ OFF

1 Press [ ] (POWER) briefly to switch the

transceiver power ON.

• Upon power up, a high pitched double beep

sounds, followed by the frequencies and other

indicators.

2 To switch the transceiver OFF, press [ ]

(POWER) again.

• When you turn the transceiver OFF, a low

pitched double beep sounds.

• The transceiver stores the parameters when it

is turned OFF. It recalls these parameters next

time you turn the transceiver ON again.

ADJUSTING VOLUME

Turn the VOL control clockwise to increase the audio

output level and counterclockwise to decrease the

output level.

• If you are not receiving a signal, press and hold

[MONI] to unmute the speaker, then adjust the

VOL control to a comfortable audio output level.

ADJUSTING SQUELCH

The purpose of the Squelch is to mute the speaker

when no signals are present. With the squelch level

correctly set, you will hear sound only while actually

receiving signals. The higher the selected squelch

level, the stronger the signals must be, to receive.

The appropriate squelch level depends on the

ambient RF noise conditions. You can configure

independent threshold squelch levels for the A-band

and B-band.

1 Press [SQL].

• The current squelch level appears.

2 Turn the Tuning control or press [ ]/ [ ] to adjust

the level.

• Select the level at which the background noise

is just eliminated when no signal is present.

• The higher the level, the stronger the signals

must be, to receive.

• 6 different levels can be set

(-- -- -- -- --: level 0 ~ || || || || ||: level 5).

3 Press [ ] or [MNU] to store the new settings or

press [ ] to cancel without changing the current

setting.

Note:

When operating in USB, LSB and CW modes, the squelch

unmutes up to level 2.

SELECTING A BAND

By default, two frequencies are displayed on the

LCD. The frequency on top is called the A-band. The

bottom frequency is called the B-band.

Press [A/B] to select the A-band or B-band for

operation. Each time you press [A/B], the “s” icon

moves, indicating which band is currently selected for

operation. Usually, select the A-band to operate the

amateur band and select the B-band to receive the

various broadcasting stations, such as AM, FM, TV

(audio only) or another amateur band {page 33}.

MULTI-SCROLL KEY

This transceiver has a 4-way cursor key with a MENU

(“MNU”) key in the center.

/ keys

The / keys function in the same way as the

Tuning control. These keys change the frequencies,

memory channels, and other selections.

Note: You can use the Tuning control in place of the / keys for

most of the controls.

/ OK key

Press to move to the next step or complete the

setting in various modes, such as Menu mode,

CTCSS frequency selection, and DCS code selection.

/ ESC key

Press to move back or cancel the entry in various

modes, such as Menu mode, CTCSS frequency

selection, and direct frequency entry.

MNU key

Press to enter the Menu mode.

In Menu mode, you can select the desired menu

number by turning the Tuning control or pressing

[ ]/ [ ]. It also functions as [OK] key.

B-band

A-band

3 GETTING ACQUAINTED

TRANSMITTING

1 To transmit, hold the transceiver approximately

5 cm (2 inches) from your mouth, then press and

hold the PTT switch and speak into the

microphone in your normal tone of voice.

• The status LED on the top panel lights red and

bar-graph meter appears.

• If you press [PTT] while you are outside of the

transmission coverage, a high pitched error

beep sounds.

2 When you finish speaking, release the PTT switch.

Note: If you transmit continuously for more than 10 minutes, the

internal time-out timer generates a warning beep and the transceiver

stops transmitting. In this case, release the PTT switch and let the

transceiver cool down for a while, then press the PTT switch again to

resume transmitting {pages 40, 51}.

■ Selecting Output Power

Selecting lower transmission power is the best

way to reduce the battery consumption, if

communication is still reliable. You can configure

different power levels for transmission {page 41}.

Press [LOW].

• Each time you press [LOW], the indicator

cycles between “H” (high), “L” (low), and “EL”

(economic low).

Note:

◆

You can store different output power setting for the A and B-

band.

◆

When you change the output power, it is reflected to all

available amateur bands for A or B-band.

SELECTING A FREQUENCY

■ VFO Mode

This is the basic mode for changing the operating

frequency. Turn the Tuning control clockwise to

increase the frequency. Turn the Tuning control

counterclockwise to decrease the frequency. Or,

press [ ]/ [ ] to change the frequency.

■ MHz Mode

If the desired operating frequency is far away from

the current frequency, it is quicker to use the MHz

tuning mode.

To adjust the MHz digit:

1 Press [MHz].

• A MHz digit blinks.

2 Turn the Tuning control or press [ ]/ [ ] to

select the desired MHz digit.

3 After selecting the desired MHz digit, press

[MHz] to exit the mode and return to normal

VFO mode {above}.

4 You may further adjust the frequency using the

Tuning control or [ ]/ [ ].

Note: MHz mode does not function in AM band.

■ Direct Frequency Entry

In addition to turn the Tuning control or press

[ ]/ [ ], there is another way of selecting the

frequency. When the desired frequency is far

away from the current frequency, you can directly

enter a frequency from the numeric keypad.

1 Press [VFO].

• You must be in the VFO mode to make the

direct frequency entry.

2 Press [ENT].

• “– – – – – –” appears.

3 Press the numeric keys ([0] to [9]) to enter

your desired frequency. [MHz] can be used to

complete the MHz digits entry.

• Pressing [ENT] fills the remaining digits (the

digits you did not enter) with 0 and

completes the entry.

• To select 145.000 MHz for example, press

[1], [4], [5] then press [ENT] to complete

the entry.

• If you want to revise the MHz digits only,

press [VFO] in place of [ENT].

3 GETTING ACQUAINTED

Example 1 (100 MHz < f < 1000 MHz)

To enter 438.320 MHz:

Key in Display

[ENT] – –– –––

[4], [3], [8] 4 3 8. – – –

[3], [2], [0] 4 3 8. 3 2 0

Note: You do not have to press [MHz] when you are entering

3-digit MHz number.

Example 2

To enter 439.000 MHz:

Key in Display

[ENT] ––– –––

[4], [3], [9] 4 3 9. – – –

[ENT] 4 3 9. 0 0 0

Example 3

To revise 144.650 MHz to 145.650 MHz:

Key in Display

1 4 4. 6 5 0

[ENT] ––– –––

[1], [4], [5] 1 4 5. – – –

[VFO] 1 4 5. 6 5 0

Example 4 (f > 1000 MHz)

To enter 1250.500 MHz (B-band only):

Key in Display

[ENT] ––– –––

[1], [2], [5], [0] 12 5 0. – – –

[5] 12 5 0. 5 – –

[ENT] 12 5 0. 5 0 0

Example 5 (f < 100 MHz)

To enter 10.500 MHz (B-band only):

Key in Display

[ENT] ––– –––

[1], [0] 1 0 – – – –

[MHz] 1 0. – – –

[5] 1 0. 5 – –

[ENT] 1 0. 5 0 0 0

Note: When pressing the last [ENT], the Fine Tuning function is

automatically activated for 10.5000 MHz.

Example 6

To enter 810 kHz (B-band only):

Key in Display

[ENT] ––– –––

[0] 0 – – – – –

[MHz] 0. – – –

[8], [1], [0] 0. 8 1 0

Note:

◆

If the entered frequency does not match the current

frequency step size, the frequency is automatically rounded

down to the next available frequency.

◆

When the desired frequency cannot be entered exactly,

check whether the Fine Tuning function is ON or not

{page 35}, and then confirm the frequency step size

{page 37}.

◆

Some frequency ranges are blocked, due to government

regulations. Refer to the specifications {pages 53, 54} for the

TX/ RX coverage.

◆

If you turn the Tuning control or press [ ]/ [ ] while entering

the frequency, the transceiver clears the entry and recovers

the previous frequency and mode.

MENU SETUP

WHAT IS A MENU?

Many functions on this transceiver are selected or

configured via a software-controlled Menu, rather

than through the physical controls of the transceiver.

Once familiar with the Menu system, you will

appreciate the versatility it offers. You can customize

the various timings, settings, and programming

functions on this transceiver to meet your needs

without using many controls and switches.

MENU ACCESS

1 Press [MNU].

• The Menu No. and setting appear on the

display, along with a brief explanation of the

Menu No.

2 Turn the Tuning control or press [ ]/ [ ] to select

your desired Menu No.

• As you change the Menu No., a brief

explanation of each Menu No. appears.

3 Press [ ] or [MNU] to configure the parameter of

the currently selected Menu No.

4 Turn the Tuning control or press [ ]/ [ ] to select

your desired parameter.

5 Press [ ] or [MNU] to store the setting.

Otherwise, press [ ] or [PTT] to cancel.

MENU FUNCTION LIST

SELECTING A MENU LANGUAGE

You can select either English or Japanese (Katakana)

for the menu description. To switch the language:

1 Press [MNU].

2 Turn the Tuning control or press [ ]/ [ ] to select

Menu No. 27.

3 Press [ ] or [MNU].

4 Turn the Tuning control or press [ ]/ [ ] to select

either “ENGLISH” or “JAPANESE”.

5 Press [ ] or [MNU] to store the setting.

Otherwise, press [ ] or [PTT] to cancel.

• When you select “JAPANESE” in step 3 and

press [ ] or [MNU], all Menu explanations are

displayed in Japanese (Katakana). To return to

English mode, repeat step 1, 2 and 3 {above}

to access Menu No. 27, then select

“ENGLISH”. Press [ ] or [MNU] to display the

Menu mode in English.

Note: The menu language selection does not affect any other

modes, such as memory name {page 17} or DTMF name {page 31}.

yalpsiDehtnO

uneM

.oN

noitcnuF snoitceleS tluafeD

.feR

gaPe

EMUSERNACS1

dohtememusernacS

edomdetarepO-emiT:EMIT

edomdetarepO-reirraC:REIRRAC

edompotsdnakeeS:KEES

/REIRRAC/EMIT

KEES

EMIT72

KNILPRG.M2 noitarugifnockniLpuorGyromeM76543210skniLoN42

DOHTEMRM3 noitidnocllaceRyromeM

/SDNABLLA

DNABTNERRUC

LLA

SDNAB

OFVGORP4

egnarycneuqerfOFVelbammargorP

)ylnodnab-A(

—

eeS

ecnerefeR

egaP

TESFFOOTUA5 noitcnuftesffOretaepeRotuAFFO/NONO31

TESFFO6 ycneuqerftesfforetaepeR

zHM59.95~00.0

fospetsni

zHM50.0

eeS

ecnerefeR

egaP

ELBANEENUT7

ehtfoesutimreP gninuT syekehtnehwlortnoc

dekcolera

FFO/NOFFO83

TIBIHNIXT8 noissimsnartehttibihnIFFO/NOFFO04

KCAJCIM/PS9ehttceleS CIM/PS noitcnufkcajCP/CNT/CIM/PSCIM/PS

4 MENU SETUP

yalpsiDehtnO

uneM

.oN

noitcnuF snoitceleS tluafeD

.feR

gaPe

EROTSFMTD01seiromemFMTDnisrebmunFMTDerotS—ataDoN13

DPSFMTD11deepsnoissimsnartenotFMTDWOLS/TSAFTSAF23

DLOHFMTD21

neewtebsdnoces2rofnoissimsnartehtdloH

seirtneyekFMTD

FFO/NOFFO13

ESUAPFMTD31

FMTDgnittimsnartelihwnoitarudesuapehT

senot

/005/052/001

/0051/0001/057

sm0002

sm00523

KCOLFMTD41syekhtiwnoissimsnartFMTDelbasiDFFO/NOFFO23

GSMNO-RWP51egassemno-rewoPsretcarahc8

!!OLLEH

TSARTNOC61

tsartnocyalpsidDCL

mumixam:61~muminim:1

61~1873

REVASTAB71doirepffo-tuhsreviecerrevasyrettaB

/6.0/4.0/2.0/FFO

/0.3/0.2/0.1/8.0

.ces0.5/0.4

.ces0.173

OPA81noitcnufffOrewoPcitamotuA.nim06/03/FFO.nim0363

PEEBYEK91noitcnufpeeBFFO/NONO73

YSUBnoXOV02

sireviecerehtnehwnoissimsnartXOVwollA

ysub

FFO/NOFFO24

NIAGXOV12

ytivitisnesniagXOVehtteS

evitisnestsom:9~evisitnestsael:0

9~0414

YALEDXOV22emityaledXOVehttsujdA

/057/005/052

/0002/0051/0001

sm0003

sm00514

YEKLLAC32yekLLACehtrofnoitcnufatceleSzH0571/LLAC

LLAC

)A6F-HT(

zH0571

)E7F-HT(

DLOH057142

sienotzH0571anehwsutatsXTehtdloH

dettimsnart

FFO/NOFFO31

TFIHSTAEB52ycneuqerfkcolcUPClanretniehttfihSFFO/NOFFO73

TNARAB62zHM1.01wolebannetnarablanretninaelbanE

/DELBANE

DELBASID

DELBANE

EGAUGNAL72egaugnalunemehttceleS

/HSILGNE

ESENAPAJ

HSILGNE

TEKCAP82deepstekcapCNTlanretxenatceleSspb0069/0021spb002154

WORRANMF92noitarepodnabworranMFFFO/NOFFO93

YRETTAB03epytyrettabatceleS

/MUIHTIL

ENILAKLA

MUIHTIL

?TESER13edomteseratceleS

/TESEROFV/ON

/TESERUNEM

TESERLLUF

ON05

4 MENU SETUP

yalpsiDehtnO .oNuneM snoitceleS tluafeD gaP.feRe

OPA81setunim06/03/FFO.nim0363

TESFFOOTUA5 FFO/NONO31

TNARAB62DELBASID/DELBANEDELBANE43

YRETTAB03ENILAKLA/MUIHTILMUIHTIL63

REVASTAB71.ces0.5/0.4/0.3/0.2/0.1/8.0/6.0/4.0/2.0/FFO.ces0.173

TFIHSTAEB52FFO/NOFFO73

YEKLLAC32zH0571/LLAC

LLAC

/)E7F-HT(

zH0571

)A6F-HT(

TSARTNOC6161~1873

DLOHFMTD21FFO/NOFFO13

KCOLFMTD41FFO/NOFFO23

ESUAPFMTD31sm0002/0051/0001/057/005/052/001sm00523

DPSFMTD11WOLS/TSAFTSAF23

EROTSFMTD01— ataDoN13

WORRANMF92FFO/NOFFO93

PEEBYEK91FFO/NONO73

EGAUGNAL72ESENAPAJ/HSILGNEHSILGNE9

DOHTEMRM3 DNABTNERRUC/SDNABLLA

LLA

SDNAB

KNILPRG.M2 76543210skniLoN42

TESFFO6 zHM50.0fospetsnizHM59.95~00.0

eeS

ecnerefeR

egaP

TEKCAP82spb0069/0021spb002154

OFVGORP4 — —93

GSMNO-RWP51sretcarahc8!!OLLEH93

?TESER13TESERLLUF/TESERUNEM/TESEROFV/ONON05

EMUSERNACS1 KEES/REIRRAC/EMITEMIT72

KCAJCIM/PS9 CP/CNT/CIM/PSCIM/PS64,54

ELBANEENUT7 FFO/NOFFO83

TIBIHNIXT8 FFO/NOFFO04

YALEDXOV22sm0003/0002/0051/0001/057/005/052sm00514

NIAGXOV129~0414

YSUBnoXOV02FFO/NOFFO24

DLOH057142FFO/NOFFO31

ALPHABETICAL FUNCTION LIST

OPERATING THROUGH REPEATERS

Repeaters, which are often installed and maintained

by radio clubs, are usually located on mountain tops

or other elevated locations. Generally they operate at

higher ERP (Effective Radiated Power) than a typical

station. This combination of elevation and high ERP

allows communications over much greater distances

than communications without using repeaters.

Most repeaters use a receive and transmit frequency

pair with a standard or non-standard offset (odd-split).

In addition, some repeaters must receive a tone from

the transceiver to allow it to access. For details,

consult your local repeater reference.

OFFSET PROGRAMMING FLOW

If you store the above data in a memory channel, you

need not reprogram every time. See “MEMORY

CHANNELS” {page 15}.

PROGRAMMING OFFSET

First select an amateur radio repeater downlink

frequency on the A-band or B-band as described in

“SELECTING A FREQUENCY” {page 7}.

■ Selecting Offset Direction

Select whether the transmit frequency will be

higher (+) or lower (–) than the receive frequency.

Press [F], [REV] to select the offset direction.

• “+” or “–” appears, indicating which offset

direction is selected.

• To program –7.6 MHz offset on the TH-F7E

(430 MHz only), repeatedly press [F], [REV]

until “ ” appears.

If the offset transmit frequency falls outside the

allowable range, transmitting is inhibited. In this

case, adjust the receive frequency so that the

transmit frequency is within the band limits.

Note: While using an odd-split memory channel or transmitting,

you cannot change the offset direction.

■ Selecting Offset Frequency

To access a repeater which requires an odd-split

frequency pair, change the offset frequency from

the default which is used by most repeaters. The

default offset frequency on the 2 m band is

600 kHz (all models); the default on the 70 cm

band is 5.0 MHz (TH-F6A) or 1.6 MHz

(TH-F7E); the default on the 1.25 m band is

1.6 MHz (TH-F6A).

1 Press [BAND] to select an amateur radio band

you want to change the offset frequency.

2 Press [MNU].

3 Turn the Tuning control or press [ ]/ [ ] to

select Menu No. 6 (OFFSET).

4 Press [ ] or [MNU].

5 Turn the Tuning control or press [ ]/ [ ] to

select the appropriate offset frequency.

• The selectable range is from 0.00 MHz to

59.95 MHz in steps of 50 kHz.

6 Press [ ] or [MNU] to store the setting.

Otherwise, press [PTT] to cancel.

TH-F7E only: If you have selected “ ” for the offset direction,

you cannot change the default (–7.6 MHz) offset frequency.

Note: After changing the offset frequency, the new offset

frequency will also be used by Automatic Repeater Offset.

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

TX: 144.725 MHz

TX tone: 88.5 Hz

RX: 145.325 MHz

Select a band.

Select a receive frequency.

Select an offset direction.

Select an offset frequency.

(only when programming odd-split

repeater frequencies)

Activate the Tone function.

(If necessary)

Select a tone frequency.

(If necessary)

5 OPERATING THROUGH REPEATERS

■ Activating Tone Function

Press [TONE] to switch the Tone function ON (or

OFF).

•“” appears when the Tone function is ON.

Note: You cannot use the Tone and CTCSS/ DCS functions at

the same time. Switching the Tone function ON after activating

the CTCSS/ DCS deactivates the CTCSS/ DCS function.

TH-F7E only: When you access repeaters that require 1750 Hz

tones, you need not activate the Tone function. Press [CALL]

without pressing the PTT switch to transmit a 1750 Hz tone

(default setting).

■ Selecting a Tone Frequency

1 While the Tone function is ON, press [F],

[TONE].

2 Turn the Tuning control or press [ ]/ [ ] to

select the desired tone frequency.

3 Press [ ] or [MNU] to complete the setting.

Otherwise, press [PTT] to cancel.

Available Tone Frequencies

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

.oN

.qerF

)zH(

100.76214.79323.141435.602

203.96310.001422.641537.012

309.17415.301524.151631.812

404.47512.701627.651737.522

500.77619.011722.261831.922

607.97718.411829.761936.332

705.28818.811928.371048.142

804.58910.321039.971143.052

905.88023.721132.681241.452

015.19128.131238.291

118.49225.631335.302

Note: 42 different tones are available for the transceiver. These

42 tones includes 37 EIA standard tones and 5 non-standard

tones.

TH-F7E only:

◆

To transmit a 1750 Hz tone, simply press [CALL] without

pressing the PTT switch (default setting). Release [CALL] to

quit transmitting. You can also make the transceiver remain

in the transmit mode for 2 seconds after releasing [CALL]; a

1750 Hz tone is not continuously transmitted. Access Menu

No. 24 (1750 HOLD) and select “ON”.

◆

If you desire to assign [CALL] for recalling the Call channel

in place of transmitting the 1750 Hz tone, access Menu

No. 23 (CALL KEY) and select “CALL”.

AUTOMATIC REPEATER OFFSET

This function automatically selects an offset direction,

according to the frequency that you select on the

2 m and 1.25 m (TH-F6A only) bands. The

transceiver is programmed for offset direction as

shown below. To obtain an up-to-date band plan for

repeater offset direction, contact your national

Amateur Radio association.

TH-F6A (U.S.A. and Canada)

This complies with the standard ARRL band plan.

–

––

144.0 145.5 146.4 147.0 147.6

145.1 146.0 146.6 147.4 148.0 MHz

S: Simplex

–

222.0

225.0 MHz223.920

TH-F7E (Europe/ Others)

S: Simplex

–

144.0

146.0 MHz145.8145.6

Note: Automatic Repeater Offset does not function when Reverse is

ON. However, pressing [REV] after Automatic Repeater Offset has

selected an offset (split) status, exchanges the receive and transmit

frequencies.

1 Press [MNU].

2 Turn the Tuning control or press [ ]/ [ ] to select

Menu No. 5 (AUTO OFFSET).

3 Press [ ] or [MNU].

4 Turn the Tuning control or press [ ]/ [ ] switch

the function ON or OFF.

5 Press [ ] or [MNU] to store the setting.

Otherwise, press [PTT] to cancel.

Note: If you select the frequency within the amateur radio band on

the B-band, the Automatic Repeater Offset function is also activated

in any modes.

5 OPERATING THROUGH REPEATERS

REVERSE FUNCTION

The reverse function exchanges a separate receive

and transmit frequency. So, while using a repeater,

you can manually check the strength of a signal that

you receive directly from the other station. If the

station’s signal is strong, both stations should move

to a simplex frequency and free up the repeater.

To swap the transmit and receive frequencies:

Press [REV] to switch the Reverse function ON (or

OFF).

• “R” appears when the function is ON.

Note: You can turn the Reverse function ON when you are operating

in Simplex mode. However, it does not change the TX/ RX

frequency.

AUTOMATIC SIMPLEX CHECK (ASC)

While using a repeater, the ASC function periodically

checks the strength of a signal that you are receiving

directly from the other station. If the station’s signal is

strong enough to allow direct contact without a

repeater, “ ” indicator on the display starts blinking.

Press [REV] (1 s) to switch the function ON.

•“” appears when the function is ON.

• While direct contact is possible, “ ” blinks.

• To quit the function, press [REV].

Note:

◆

Pressing the PTT switch causes “ ” icon to quit blinking.

◆

ASC can be activated while operating in Simplex mode.

However, it does not change the TX/ RX frequencies.

◆

ASC does not function while scanning.

◆

Activating ASC while using Reverse switches Reverse OFF.

◆

If you recall a memory channel or the Call channel that contains

a Reverse ON status, ASC is switched OFF.

◆

ASC causes received audio to be momentarily intermitted every

3 seconds.

◆

ASC does not function when the band is not selected for

operation.

TONE FREQ. ID SCAN

This function scans through all tone frequencies to

identify the incoming tone frequency on a received

signal. You may use the function to find which tone

frequency is required by accessing your local

repeater.

1 While the Tone function is ON, press [F],

[TONE] (1 s) to start the Tone Freq. ID scan.

• When the transceiver receives the signal, the

scan starts.

• To reverse the scan direction, turn the Tuning

control or press [ ]/ [ ].

• To quit the function, press [PTT] or [ ].

• When the tone frequency is identified, a beep

sounds and the identified frequency appears.

2 Press [ ] to program the identified frequency in

place of the current tone frequency.

• Press [ ] if you do not want to program the

identified frequency.

• Press [ ]/ [ ] while the identified frequency is

blinking, to resume scanning.

Note: Some repeaters do not re-transmit the access tone in the

downlink signal. In this case, check the other station’s uplink signal

to detect the repeater access tone.

144.725 MHz

145.325 MHz

144.725 MHz

TX: 144.725 MHz TX: 144.725 MHz TX: 144.725 MHz TX: 145.325 MHz

RX: 145.325 MHz RX: 145.325 MHz RX: 145.325 MHz RX: 144.725 MHz

MEMORY CHANNELS

In memory channels, you can store frequencies and

related data that you often use. Then you need not

reprogram those data every time. You can quickly

recall a programmed channel through simple

operation. A total of 400 memory channels are

available for storing the frequencies, modes and

other operating conditions of the A and B-bands.

SIMPLEX & REPEATER OR

ODD-SPLIT MEMORY CHANNEL?

You can use each memory channel as a simplex &

repeater channel or an odd-split channel. Store only

one frequency to use as a simplex & repeater

channel or two separate frequencies to use as an

odd-split channel. Select either application for each

channel depending on the operations you have in

mind.

Simplex & repeater channels allow:

• Simplex frequency operation

• Repeater operation with a standard offset

(if an offset direction is stored)

Odd-split channels allow:

• Repeater operation with a non-standard offset

Note: Not only can you store data in memory channels, but you can

also overwrite existing data with new data.

The data listed below can be stored in each memory

channel:

retemaraP

&xelpmiS

retaepeR

tilpS-ddO

ycneuqerfevieceR

seY

ycneuqerftimsnarTseY

ycneuqerfenoTseYseY

NOenoTseYseY

ycneuqerfSSCTCseYseY

NOSSCTCseYseY

edocSCDseYseY

NOSCDseYseY

noitceridtesffOseYA/N

ycneuqerftesffOseYA/N

NOesreveRseYA/N

ezispetsycneuqerFseYseY

tuokcollennahcyromeMseYseY

emanlennahcyromeMseYseY

NOgninutENIFseYseY

noitcelesedoMseYseY

Yes: Can be stored in memory.

N/A: Cannot be stored in memory.

Note: The transmit frequency must be on the same band as the

receive frequency band (Odd-split channel).

STORING SIMPLEX FREQUENCIES OR

STANDARD REPEATER FREQUENCIES

1 Press [VFO].

2 Turn the Tuning control or press [ ]/ [ ] to select

your desired frequency in the amateur radio

bands.

• You can also directly enter desired frequency

using the keypad {page 7}.

3 If storing a standard repeater frequency, select the

following data:

• Offset direction {page 12}

• Tone function, if necessary {page 13}

• CTCSS/ DCS function, if necessary

{pages 28, 29}

If storing a simplex frequency, you may select

other related data (CTCSS or DCS settings, etc.).

4 Press [F].

• A memory channel number appears and blinks.

•“” indicates the current channel is empty; “ ”

appears if the channel contains data.

• Memory channel number L0/U0 ~ L9/U9

{page 23}, I–0 ~ I–9 {page 20}, and Pr1 and

Pr2 {page 25} are reserved for other functions.

5 Turn the Tuning control or press [ ]/ [ ] to select

the memory channel in which you want to store

the data.

6 Press [MR] ([ ] or [MNU]) to store the data to the

channel.

STORING ODD-SPLIT REPEATER FREQUENCIES

Some repeaters use a receive and transmit frequency

pair with a non-standard offset. If you store two

separate frequencies in a memory channel, you can

operate on those repeaters without programming the

offset frequency and direction.

1 Store the desired receive frequency and related

data by the procedure given for simplex or

standard repeater frequencies {above}.

2 Turn the Tuning control or press [ ]/ [ ] to select

the desired transmit frequency.

3 Press [F].

4 Turn the Tuning control or press [ ]/ [ ] to select

the memory channel you programmed in step 1.

5 Press [PTT]+[MR] ([PTT]+[ ] or [PTT]+[MNU]).

• The transmit frequency is stored in the memory

channel.

Note:

◆

When you recall an odd-split memory channel, “+” and “–” appear

on the display. To confirm the transmit frequency, press [REV].

◆

When you revise only the transmission frequency for the odd-split

channel, the frequency step size must be the same as the

original odd-split channel memory data.

La pagina sta caricando ...

Kenwood TH-F6A Manuale utente

Marca: Kenwood

Modello: TH-F6A

Categoria: Radio a due vie

Tipo: Manuale utente

Questo manuale è adatto anche per

TH-F7E

Scarica il pdf

rapporto

in altre lingue

English: Kenwood TH-F6A User manual

Kenwood TH-F6A Manuale utente

Questo manuale è adatto anche per

Kenwood TH-F6A Manuale utente

in altre lingue

Documenti correlati

Altri documenti