DTS ECO 500 Guida d'installazione
- Categoria
- Gate Opener
- Tipo
- Guida d'installazione
1
Base plate-mounting instructions
E-EEEE
DTS ECO 500
SLIDING GATE MOTOR
INSTALLATION MANUAL
DTS SECURITY
P.O.BOX 3399
EDENVALE
1610
TELEPHONE 086 1000 387
Spartan +2711 392 5540 (H/O)
Pretoria +2712 361 5528
Alberton +2711 907 8846
Natal +2731 916 4002
www.dtssecurity.co.za
2
BASE PLATE MOUNTING INSTRUCTIONS
1. Assemble base plate by fastening M10x30 Hex set screws into base plate from under
the base plate up and tightening into position.
2. Mount base plate with bolts 160mm from the centre of the gate track and centre of base plate a
minimum of 250mm away from the gate opening.
3. Secure the base plate to the gate track by welding the base plate directly to the gate track. (Ensuring
a distance of 160mm from centre of gate track to centre of fastening screws).
4. Fit all required cabling through hole provided in base plate.
5. Support the back of the base plate with 40x40x3 angle iron (not provided) or similar off cut steel
knocked approximately 300 to 400mm into the ground.
6. Fill area below and around the base plate with approximately 300x400x300 concrete to ensure that
the motor will be secure.
7. NOTE - For SAFETY reasons, ALL motors should be fitted with a set of IR beams.
Gearbox mounting instructions
1. Fit gearbox over mounting bolts protruding from base plate.
2. Slide gate fully open and closed, insuring pinion gear has approximately 5mm clearance to gate at
all times.
3. Fasten gearbox down firmly to base plate using M10 washers and nuts.
How to override the gate motor for manual operation
1. Unlock and open the override lever on the gearbox.
2. The gate can now be opened and closed manually.
Rack mounting instructions
1. Unlock and open manual override lever fully to disengage gearbox. (See above).
2. Using a 2.5 to 3mm spacer between the pinion gear and the rack, mount the rack
using Tek screws No12x20 (not provided) and screw the rack to the gate starting
from the tail of the gate and ensuring that the rack is mounted level.
(A 2.5 to 3mm spacer can also be put between motor and base plate when fitting rack. This must be
removed once the rack is in place).
NB: Ensure that one of the screws attaching the nylon rack to the angle is in line with the
read switch or limit switch spring when the gate is fully closed and open position.
3
Limit switch actuator mounting instructions
1. Remove the screw attaching the nylon rack to the angle that is closest to the position of the spring
on the motor when the gate is in the close and open position.
2. Fit limit switch actuators with screws provided onto the nylon rack.
3. Setting the gate close actuator – Close the gate with approximately 120mm gap between gate and
close stopper. Now move the actuator until the close LED lights up. Fasten the actuator.
4. Setting the gate open actuator – Open the gate with approximately 120mm gap between gate and
open stopper. Now move the actuator until the open LED lights up. Fasten the actuator.
5. (The gate must never bump against the close or open end stoppers).
Spring limit actuator
Important:
For safety reasons, a solid stop must be fitted at both ends of the gate to prevent the gate
from moving past its full open or close position.
Low voltage Plug in transformer.
Connect 16volt AC from the transformer to the charger board marked as 16 VAC supply.
Low voltage on board (OBT) transformer – 220V at gate.
Connect 220V AC to input side of Eco500/16volt AC transformer (black & brown wires), or to
NEL (Neutral/Earth/ Live) connector on side of transformer, then connect the output wires (red) to
the charger board marked as 16 VAC supply.
DO NOT CONNECT 220V DIRECTLY TO PCB
WHEN 220V IS USED AT GATE MOTOR, A SEPARATE DOUBLE POLE ISOLATOR MUST
BE FITTED WITHIN 1METER FROM THE MOTOR.
4
Diagram to connect IR Beams to PCB
Note: If sentry beams are fitted, then SBEAM, N/C on the PCB must be connected to N/O on the RX.
Pedestrian Opening (Default 1 meter / 8 seconds auto close)
Load setting
To adjust the load turn the load pot to determine the load setting (Minimum, anticlockwise & Maximum, clockwise).
PCB Control card.
(Please note, can only connect a low voltage power supply and therefore cannot be modified as a High excess motor)
5
ON BOARD RECEIVER PROGRAMMING
The onboard receiver is designed to work with most rolling code transmitters.
The button used for BT LRN CANNOT be used for PD LRN and vice versa.
To individually erase transmitters:
To erase a button from the receiver, in case of incorrect programming i.e. blue button should be for BT LRN
and not PD LRN.
Simply push and hold the BT LRN button for 5 seconds, the RX led will light up and the Close & Open
led will flash once. Release the BT LRN button. Now push and release the TX button you want to erase, the RX, Close &
Open led will flash twice as confirmation. The TX is erased and can be re-learned into correct input.
To master erase:
Push and hold the BT LRN button, after 5 seconds the RX led will light up. Keep holding for another 5 - 10
seconds then the Close & Open will start flashing. Release BT LRN button. The RX led will flash 5 times as
indicating, all transmitters erased.
Note: When memory full & trying to program remote (TX) no.32,
the Close & Open led will give a burst of
rapid flashes for 1.5 seconds after releasing the BT LRN button indicating, receiver (RX) is full.
The RX will abort programming automatically.
A TX must then be deleted before a next TX can be programmed to the RX.
If a transmitter is already programmed, the RX led will go off on the 1
st
press from the TX.
PROGRAMMING A
TRANSMITTER (TX) FOR FULL
OPEN OPERATION – BT LRN
(Version 1.3)
PROGRAMMING A
TRANSMITTER FOR
PEDESTRIAN OPERATION - PD
LRN (Version 1.3)
1. Push the BT LRN button, the
RX led will go on.
2. Push the required button on the
transmitter, at arms length from
PCB once, the Rx led will flash.
Press the same button again, the
RX, Close & Open led will flash 3
times for a full Keelog transmitter
or twice for other transmitters.
3.
Repeat Step 1 and 2 for additional
transmitters. Up to 31 transmitter
(Slots) signals can be
programmed as a joint
combination between BT LRN &
PD LRN.
1. Push the PD LRN button, the
RX led will go on.
2. Push the required button on the
transmitter, at arms length from
PCB once, the Rx led will flash.
Press the same button again, the
RX, Close & Open led will flash 3
times for a full Keelog transmitter
or twice for other transmitters.
3. Repeat Step 1 and 2 for additional
transmitters. Up to 31 transmitter
(Slots) signals can be programmed
as a joint combination between BT
LRN & PD LRN.
6
ELECTRONICS
FEATURES:
1. Standard mode.
2. Easy motor direction change. (via jumper)
3. Auto close facility. (Infra red beams must be fitted if auto close is activated).
1. Standard Mode. (No function selected).
When the gate is activated it will open and can be stopped in mid cycle by pressing the
transmitter or manual push button. Pressing the transmitter or push button can reverse the
gate. In standard mode the gate will remain on its open limit until it is triggered to close.
If main power fails, the motor will still operate until battery reaches 9.5Volt
.
Change to
manual by overriding the motor by the override lever. When the main power comes on
again, lock in the override lever and the motor will function as normal.
2. Easy motor direction change.
By selecting the jumper, the motor direction and the limit wires are changed
automatically. (Please note: the gate must close on first trigger after power up).
3. Auto close. (20 seconds, fixed) (Infra-red beams must be fitted if auto close is selected).
When Auto close is selected via the jumper on the PCB and the Gate opens to the open
limit, the gate will wait the factory default time before automatically closing. If the gate is
triggered while the gate is in its closing cycle it will stop and reopen.
If the transmitter or manual push button is pressed while the gate is in its opening cycle, the
gate will stop and close after the factory default auto close time (from any position, not
only from the open limit).
4. Pedestrian function
A default auto close time (8 Seconds) and opening distance (Approximately 1 meter) has
been preprogrammed and cannot be changed.
List of LED indications.
NB – When connecting intercoms to the control card (IT and CMN), please ensure that your intercom
trigger output is potential free (ZERO voltage). If not, a gate relay module must be fitted.
-
LED ON when open limit is activated. (gate
open).
- LED OFF when close limit is activated. (gate closed).
- LED flashing SLOW (1 sec. on/1 sec. off) (gate is in motion).
- LED flashes 2 long/3 short continuously (gate is stopped midway).
- LED flashes fast (250ms on/250ms off) continuously. (gate in overload).
- LED flashes 3 fast flashes every 1.5 seconds. (Battery low, <11VDC).
7
TROUBLESHOOTING
SYMPTOMS
CAUSES
ACTION
When pressing the remote transmitter or
manual push button the gate operator
will not respond at all.
PCB responds but gate will not open.
The gate opens but will not close.
The gate when closing stops and reverses
or when opening stops.
Gate does not remain open.
The unit opens partially and stops and
then auto closes.
When gate reaches a limit actuator, the
unit does not stop running.
Gate motor is jumping teeth on the rack.
Gate jams in the open or closed position
and is not easy to manually release.
Gate opens pedestrian when full open
trigger is given.
Gate auto opens
Open & Close Led flashes
simultaneously
Transmitter battery flat.
Transmitter or manual push button is
physically damaged.
Transmitter has not been programmed into
the receiver memory or manual push button
is not connected to the PCB or push button.
Motor/Load fuse is faulty or motor brushes
not making contact with armature.
Safety infra-red beams are obstructed or the
beams equipment/cabling are faulty or
incorrectly wired.
The unit is sensing an obstruction
The infra-red beam has been triggered.
Another trigger has been received by the
control card.
Auto close has been activated.
Another user has triggered the unit.
The pedestrian (PT) mode on the PCB is
being triggered.
A transmitter code has been programmed
incorrectly into the pedestrian (PD LRN)
function of the receiver.
Limit input wired incorrectly (out of sync’
with the motor direction.)
Limit switch is faulty.
Pinion to rack spacing is incorrect.
Rack is insufficiently fastened to gate leaf.
Debris on track.
Gate is running too far.
Gate is running past its limit actuator.
Gate is overloading in the close position
after it received a pedestrian trigger.
Jumper for motor direction is
incorrectly selected and auto close is
active.
Receiving a trigger from somewhere
else.
The gate motor was over loaded.
Replace transmitter battery.
Check with supplier.
Follow the receiver setup instructions.
Check wiring between PCB and push
button.
Replace fuse. (Fast blow fuse).
Repair or replace motor brushes.
Clear obstruction, repair or replace safety
infra-red beams equipment/cable, fix
incorrect wiring connections.
Clear obstruction or adjust load sensing.
Clear obstruction.
Check with other operators on the system.
De-activate auto close or use auto close
override.
Check with other operators on the
system.
Check equipment /cabling attached to the
pedestrian (PT) on the PCB input.
Delete the transmitter and re-program the
transmitter into the receivers (BT LRN) as
per instructions.
Re-wire
Change limit switch or check with supplier.
Re-align.
Re-align and correct fastening.
Clean track.
Adjust the limit actuators until there is a gap
between gate and stoppers of approximately
10 – 15 mm
Replace the switch, rewire correctly or
check limit spring assembly.
Move the closing limit actuator towards the
closing cycle approximately 10mm.
Select correct positioning of motor
direction jumper.
Check wiring to inputs CMN & IT
connections on PCB.
Master erase onboard RX and re-learn
all transmitters.
Find and fix the cause for overloading
the motor.
8
Manufacturers warranty
.
• All motors manufactured by DTS Security carry a 24 month factory warranty
from date of invoice. (Excluding batteries & Remote controls).
• Batteries & remote controls carry a 12 months warranty.
(Remote batteries are consumables and therefore carry NO warranty)
• All goods are warranted to be free from faulty components and manufacture.
• Faulty goods will be repaired or replaced at the sole discretion of DTS Security
Products, free of charge.
• This warranty is subject to the goods being returned to the premises of DTS
Security Products.
• This warranty excludes lightning damage, insect damage and damage caused
by faulty installation.
• In the event of the goods being supplied by dealer, merchant, agent or duly
appointed installer of DTS Security Products, the claim must be directed to
that supplier.
• The carriage of goods is for the customer’s account.
• This warranty is only valid if the correct installation and application of goods,
as laid out in the applicable documentation accompanying said goods, is
adhered to.
• All warranty claims must be accompanied by the original invoice.
• The liability of DTS Security Products and / or their distributors is limited as
herein set out DTS Security Products and / or their distributors will not be liable
for consequential, incident damage or injury howsoever arising.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
DTS ECO 500 Guida d'installazione
- Categoria
- Gate Opener
- Tipo
- Guida d'installazione
in altre lingue
- English: DTS ECO 500 Installation guide
Altri documenti
-
BFT Deimos Ultra BT A Manuale utente
-
-
-
-
-
Elvox RS04 Istruzioni per l'uso
-
-
-
-